Chapter 5 · Solutions

5.3 Colligative Properties and the van't Hoff Factor

Dissolve a non-volatile solute and four properties of the solvent shift together: its vapour pressure falls, its boiling point rises, its freezing point falls and an osmotic pressure appears. All four depend only on how many solute particles are present — which lets you weigh molecules you cannot see, and the van't Hoff factor $i$ tells you whether they split up or pair up in solution.

On a winter morning in Srinagar or Shimla, road crews spread salt on icy roads, and the ice turns to slush even though the air is below $0\ ^\circ\mathrm{C}$. A car radiator in Ladakh is filled with water mixed with ethylene glycol so that it neither freezes at night nor boils over on a long climb. A hospital drip is not pure water but $0.9\%$ saline, because pure water pumped into a vein would make the red blood cells swell and burst. On the coast near Chennai, desalination plants push seawater at high pressure against plastic membranes and collect fresh drinking water on the other side. And a biochemist who has isolated a new protein finds its molar mass — perhaps $60\,000\ \mathrm{g\,mol^{-1}}$ — by measuring a pressure of a couple of hundred pascals.

All of these rest on one fact. When a non-volatile solute is dissolved in a solvent, the solvent's "escaping tendency" is reduced, and four measurable properties change: the vapour pressure falls, the boiling point rises, the freezing point falls and an osmotic pressure appears. In dilute solutions each change depends only on the number of solute particles, not on what they are — they are colligative properties (from the Latin colligatus, "bound together"). In this section we build all four from Raoult's law of Section 5.2, use them to find molar masses, and then explain the "abnormal" molar masses that appear when solutes dissociate into ions or associate into clusters, using the van't Hoff factor. The concentration units — mole fraction, molality and molarity — are those of Section 5.1.

Colligative properties and the relative lowering of vapour pressure

Picture the surface of pure water in a closed flask. Molecules at the surface with enough energy escape into the vapour; vapour molecules strike the surface and are recaptured. At equilibrium the two rates balance, and the pressure of the vapour is the vapour pressure $p_1^\circ$ of the pure solvent. Now dissolve some glucose. Glucose molecules have essentially no tendency to evaporate, but they occupy part of the solution — and, more importantly, mixing makes the liquid more disordered, so the solvent molecules have less "reason" to leave. Fewer solvent molecules escape per second, and the vapour pressure settles at a lower value $p_1$. The amount of the lowering does not care whether the particles are glucose, urea or sucrose; it cares only about the fraction of particles that are not solvent.

📘 Definition 5.10 — Colligative property

A colligative property of a solution is a property that, for a dilute solution, depends only on the number of solute particles (molecules or ions) present in a given amount of solvent, and not on their chemical nature, size or mass. The four colligative properties are:

  1. the relative lowering of vapour pressure of the solvent;
  2. the elevation of the boiling point;
  3. the depression of the freezing point;
  4. the osmotic pressure.

Conditions: the solution is dilute (so that it behaves ideally, obeying Raoult's law for the solvent); the solute is non-volatile (for vapour pressure and boiling point); and on freezing, only pure solid solvent separates (for freezing point). If the solute dissociates or associates, "number of particles" means the number actually present in solution — the subject of the last part of this section.

From Raoult's law. For a solution of a non-volatile solute (component 2) in a solvent (component 1), only the solvent contributes to the vapour, and Raoult's law gives $p_1=x_1p_1^\circ$, where $x_1$ is the mole fraction of the solvent. The lowering is $\Delta p_1=p_1^\circ-p_1=p_1^\circ(1-x_1)=x_2\,p_1^\circ$. The lowering $\Delta p_1$ itself depends on the solvent (through $p_1^\circ$), but the relative lowering does not:

📐 Result 5.6 — Relative lowering of vapour pressure

For a solution of a non-volatile, non-electrolyte solute that obeys Raoult's law, the relative lowering of the vapour pressure of the solvent equals the mole fraction of the solute:

$$\frac{p_1^\circ-p_1}{p_1^\circ}=x_2=\frac{n_2}{n_1+n_2}.$$

Rearranging gives the equivalent exact form (useful for numericals):

$$\frac{p_1^\circ-p_1}{p_1}=\frac{n_2}{n_1}=\frac{w_2\,M_1}{M_2\,w_1}.$$

For a dilute solution $n_2\ll n_1$, so $x_2\approx n_2/n_1$ and the relative lowering is proportional to the molality $m$ of the solute: $\dfrac{\Delta p_1}{p_1^\circ}\approx\dfrac{m\,M_1}{1000}$ (with $M_1$ in $\mathrm{g\,mol^{-1}}$). Here $w_1, w_2$ are the masses and $M_1, M_2$ the molar masses of solvent and solute.

To see where the exact form comes from: $\dfrac{p_1^\circ-p_1}{p_1}=\dfrac{x_2p_1^\circ}{x_1p_1^\circ}=\dfrac{x_2}{x_1}=\dfrac{n_2}{n_1}$. It needs no "dilute" approximation and is the quickest route to a molar mass when the vapour pressure of the solution is given.

Molar mass from vapour pressure. Solving the exact form for $M_2$:

$$M_2=\frac{w_2\,M_1\,p_1}{w_1\,(p_1^\circ-p_1)}.$$

The dilute version replaces $p_1$ by $p_1^\circ$ in the numerator. In practice vapour-pressure lowering is small and awkward to measure accurately — a $0.1\ \mathrm{mol\,kg^{-1}}$ aqueous solution lowers the vapour pressure by only $0.18\%$ — so the method is rarely used in the laboratory, but it is a favourite of examiners because it links directly to Raoult's law.

✏️ Example 1 — Vapour pressure over a glucose solution
$18.0$ g of glucose ($\mathrm{C_{6}H_{12}O_{6}}$, $M=180\ \mathrm{g\,mol^{-1}}$) is dissolved in $178.2$ g of water at $25\ ^\circ\mathrm{C}$, where the vapour pressure of pure water is $23.76\ \mathrm{mm\,Hg}$. (a) Find the mole fraction of glucose and the vapour pressure of the solution. (b) Find the molality of the solution. (c) What mass of urea ($\mathrm{CO(NH_{2})_{2}}$, $60\ \mathrm{g\,mol^{-1}}$) in the same mass of water would give the same vapour pressure?
Moles $n_2=\dfrac{18.0}{180}=0.100\ \mathrm{mol}$; $n_1=\dfrac{178.2}{18.0}=9.90\ \mathrm{mol}$; $x_2=\dfrac{0.100}{10.00}=0.0100$.
(a) $p_1=x_1p_1^\circ=0.990\times23.76=23.52\ \mathrm{mm\,Hg}$, a lowering of $0.24\ \mathrm{mm\,Hg}$ — exactly $1.00\%$ of $p_1^\circ$.
(b) $m=\dfrac{n_2}{w_1/1000}=\dfrac{0.100}{0.1782}=0.561\ \mathrm{mol\,kg^{-1}}$.
(c) The same vapour pressure needs the same mole fraction, i.e. the same number of solute molecules: $0.100\ \mathrm{mol}$ of urea $=6.00$ g. One-third the mass of glucose does the same job, because each urea molecule is one-third as heavy.
Check Dilute form: $\dfrac{mM_1}{1000}=\dfrac{0.561\times18}{1000}=0.0101\approx x_2$ ✓.
✏️ Example 2 — Molar mass from the lowering of vapour pressure
At $25\ ^\circ\mathrm{C}$ pure benzene ($\mathrm{C_{6}H_{6}}$, $78\ \mathrm{g\,mol^{-1}}$) has a vapour pressure of $12.70\ \mathrm{kPa}$. When $5.00$ g of a non-volatile, non-electrolyte solid is dissolved in $78.0$ g of benzene, the vapour pressure falls to $12.39\ \mathrm{kPa}$. (a) Find the molar mass of the solid using the exact relation. (b) What value does the "dilute" approximation $x_2\approx n_2/n_1$ with $\Delta p/p_1^\circ$ give, and how large is the error?
Find the molar mass from the exact relation before you open the solution:
Data $n_1=\dfrac{78.0}{78}=1.00\ \mathrm{mol}$; $\Delta p=12.70-12.39=0.31\ \mathrm{kPa}$.
(a) Exact $\dfrac{\Delta p}{p_1}=\dfrac{n_2}{n_1}$: $n_2=1.00\times\dfrac{0.31}{12.39}=0.0250\ \mathrm{mol}$, so $M_2=\dfrac{5.00}{0.0250}=200\ \mathrm{g\,mol^{-1}}$.
(b) Approximate $\dfrac{\Delta p}{p_1^\circ}=\dfrac{0.31}{12.70}=0.0244\approx\dfrac{n_2}{n_1}$ gives $n_2=0.0244\ \mathrm{mol}$ and $M_2=205\ \mathrm{g\,mol^{-1}}$ — about $2.5\%$ too high, because a mole fraction of $0.024$ is not really "very small".
Lesson When the solution's vapour pressure is given, use $\Delta p/p_1=n_2/n_1$: it is exact and no harder. Use the dilute form only when the problem says "dilute" or gives the relative lowering directly.

Equal masses of glucose ($180\ \mathrm{g\,mol^{-1}}$) and sucrose ($342\ \mathrm{g\,mol^{-1}}$) are dissolved in equal masses of water. Which solution shows the larger relative lowering of vapour pressure?

Elevation of boiling point and depression of freezing point

A liquid boils when its vapour pressure equals the external pressure — at $1\ \mathrm{atm}$ ($101.3\ \mathrm{kPa}$) for the "normal" boiling point. Because the solution's vapour pressure is lower than the pure solvent's at every temperature, the solution has to be heated further before its vapour pressure reaches $1\ \mathrm{atm}$. Its boiling point $T_b$ is higher than that of the solvent, $T_b^\circ$, by $\Delta T_b=T_b-T_b^\circ$.

A liquid freezes at the temperature where the liquid and the solid have the same vapour pressure — there the two phases are in equilibrium. When a dilute solution freezes, the crystals that separate are pure solid solvent (sea ice is almost fresh). The vapour-pressure curve of the solid solvent is untouched by the solute, but the solution's curve has been pushed down, so the two curves now meet at a lower temperature: the freezing point falls by $\Delta T_f=T_f^\circ-T_f$. The interactive below draws both crossings.

📘 Definition 5.11 — Boiling-point elevation, freezing-point depression and the molal constants

The elevation of boiling point $\Delta T_b=T_b-T_b^\circ$ and the depression of freezing point $\Delta T_f=T_f^\circ-T_f$ are, for dilute solutions, proportional to the molality $m$ of the solute:

$$\Delta T_b=K_b\,m,\qquad \Delta T_f=K_f\,m.$$

The proportionality constants depend only on the solvent. $K_b$ is the molal elevation constant or ebullioscopic constant; $K_f$ is the molal depression constant or cryoscopic constant. Each equals the change of temperature that a $1\ \mathrm{mol\,kg^{-1}}$ solution would show if it stayed ideal, and is measured in $\mathrm{K\,kg\,mol^{-1}}$.

Why molality and not molarity? Molality is moles of solute per kilogram of solvent. It is fixed by two masses, so it does not change as the solution is heated or cooled — unlike molarity, whose volume expands with temperature. For the dilute solution $x_2\approx n_2/n_1=mM_1/1000$, so a temperature shift that is proportional to $x_2$ is proportional to $m$.

What fixes $K_b$ and $K_f$? Combining Raoult's law with the way vapour pressure changes with temperature (the Clausius–Clapeyron relation) gives, for $M_1$ in $\mathrm{g\,mol^{-1}}$ and the enthalpies in $\mathrm{J\,mol^{-1}}$:

📐 Result 5.7 — Boiling-point elevation and freezing-point depression

For a dilute solution of a non-electrolyte of molality $m$ (non-volatile for boiling; pure solvent freezing out for freezing):

$$\Delta T_b=K_b\,m,\qquad \Delta T_f=K_f\,m,$$ $$K_b=\frac{R\,(T_b^\circ)^2\,M_1}{1000\,\Delta_{vap}H},\qquad K_f=\frac{R\,(T_f^\circ)^2\,M_1}{1000\,\Delta_{fus}H}.$$

With $m=\dfrac{1000\,w_2}{M_2\,w_1}$ ($w_1, w_2$ in grams), the molar mass of the solute follows from either measurement:

$$M_2=\frac{1000\,K_b\,w_2}{\Delta T_b\,w_1}=\frac{1000\,K_f\,w_2}{\Delta T_f\,w_1}.$$

$\Delta T$ is a temperature difference, so it has the same value in kelvin and in degrees Celsius.

Two consequences of the formulas for $K$ are worth knowing. First, both constants contain only solvent properties — its molar mass, its normal boiling or freezing point and its enthalpy of vaporisation or fusion — confirming that the effect is colligative. Second, the enthalpy of fusion of most solvents is much smaller than their enthalpy of vaporisation, so $K_f$ is usually larger than $K_b$. For water $\Delta_{fus}H=6.01\ \mathrm{kJ\,mol^{-1}}$ but $\Delta_{vap}H=40.7\ \mathrm{kJ\,mol^{-1}}$, and $K_f$ is $3.6$ times $K_b$. Freezing-point measurements are therefore more sensitive, and they are done at low temperature, where a delicate solute is safe.

Solvent$T_b^\circ/\mathrm{K}$$K_b/(\mathrm{K\,kg\,mol^{-1}})$$T_f^\circ/\mathrm{K}$$K_f/(\mathrm{K\,kg\,mol^{-1}})$
water373.150.52273.151.86
ethanol351.51.20155.71.99
benzene353.32.53278.65.12
ethanoic (acetic) acid391.13.07289.83.90
camphor——452about 40

The enormous $K_f$ of camphor is used in a quick laboratory method for organic compounds: a few milligrams of the compound melted with camphor lowers its melting point by several kelvin, which an ordinary thermometer can read.

✏️ Example 3 — Antifreeze for a mountain radiator
A car radiator holds $5.00$ kg of water. (a) What mass of ethylene glycol (ethane-1,2-diol, $\mathrm{C_{2}H_{6}O_{2}}$, $62\ \mathrm{g\,mol^{-1}}$) must be added so that the coolant does not freeze above $-10.0\ ^\circ\mathrm{C}$? (b) What is the boiling point of this coolant at $1\ \mathrm{atm}$? (c) Why is methanol, which is cheaper and lighter, a poor choice? Take $K_f=1.86$ and $K_b=0.52\ \mathrm{K\,kg\,mol^{-1}}$ for water.
Molality $\Delta T_f=10.0\ \mathrm{K}$, so $m=\dfrac{\Delta T_f}{K_f}=\dfrac{10.0}{1.86}=5.38\ \mathrm{mol\,kg^{-1}}$.
(a) $n=5.38\times5.00=26.9\ \mathrm{mol}$; mass $=26.9\times62=1.67\times10^{3}\ \mathrm{g}=1.67$ kg.
(b) $\Delta T_b=K_bm=0.52\times5.38=2.8\ \mathrm{K}$; the coolant boils at about $102.8\ ^\circ\mathrm{C}$ — antifreeze is also "anti-boil".
(c) Methanol is volatile (it boils at $65\ ^\circ\mathrm{C}$): it evaporates from a hot engine, and a volatile solute raises the vapour pressure instead of lowering it, so the boiling-point formula does not apply. Ethylene glycol is practically non-volatile.
Check A $5.4\ \mathrm{mol\,kg^{-1}}$ solution is far from dilute, so these are estimates; real coolant tables give a slightly lower freezing point for this mixture. NEET problems always intend the simple formula.
✏️ Example 4 — How many atoms in a molecule of sulphur?
(a) A solution of $0.256$ g of sulphur in $20.0$ g of carbon disulphide boils $0.120\ \mathrm{K}$ higher than pure $\mathrm{CS_{2}}$. Taking $K_b(\mathrm{CS_{2}})=2.40\ \mathrm{K\,kg\,mol^{-1}}$, find the molar mass of dissolved sulphur and its molecular formula ($A_r(\mathrm{S})=32$). (b) Calculate $K_f$ for water from $\Delta_{fus}H=6.01\ \mathrm{kJ\,mol^{-1}}$ at $273.15\ \mathrm{K}$, with $R=8.314\ \mathrm{J\,mol^{-1}\,K^{-1}}$ and $M_1=18.015\ \mathrm{g\,mol^{-1}}$.
(a) Molar mass $M_2=\dfrac{1000\,K_b\,w_2}{\Delta T_b\,w_1}=\dfrac{1000\times2.40\times0.256}{0.120\times20.0}=256\ \mathrm{g\,mol^{-1}}$.
Formula Atoms per molecule $=\dfrac{256}{32}=8$: sulphur dissolves as $\mathrm{S_{8}}$ molecules (the crown-shaped rings found in the solid).
(b) $K_f=\dfrac{R(T_f^\circ)^2M_1}{1000\,\Delta_{fus}H}=\dfrac{8.314\times(273.15)^2\times18.015}{1000\times6010}=1.86\ \mathrm{K\,kg\,mol^{-1}}$.
Units $\dfrac{(\mathrm{J\,mol^{-1}\,K^{-1}})(\mathrm{K^2})(\mathrm{g\,mol^{-1}})}{(\mathrm{g\,kg^{-1}})(\mathrm{J\,mol^{-1}})}=\mathrm{K\,kg\,mol^{-1}}$ ✓ — the "1000" carries grams to kilograms.
Check The same formula with $\Delta_{vap}H=40.66\ \mathrm{kJ\,mol^{-1}}$ at $373.15\ \mathrm{K}$ gives $K_b=0.513\ \mathrm{K\,kg\,mol^{-1}}$, matching the tabulated $0.52$.

In the boiling and freezing lab, choose water, the solute NaCl ($i=2$) and $m=0.50\ \mathrm{mol\,kg^{-1}}$. Where does the solution freeze?

With water, NaCl ($i=2$) and $m=0.50$ the readouts show $\Delta T_b=0.52\ \mathrm{K}$, $\Delta T_f=1.86\ \mathrm{K}$, boils at $100.52\ ^\circ\mathrm{C}$ and freezes at $-1.86\ ^\circ\mathrm{C}$. Each formula unit gives two ions, $\mathrm{Na^{+}}$ and $\mathrm{Cl^{-}}$, so there are $1.0\ \mathrm{mol}$ of particles per kilogram — the solvent "sees" the same crowd as in $1.0\ \mathrm{mol\,kg^{-1}}$ glucose. On the left panel the red solution curve meets the blue ice curve about $1.83\ \mathrm{K}$ below the pure-water crossing, and on the right it reaches the $1\ \mathrm{atm}$ line $0.52\ \mathrm{K}$ late (the verdict line quotes these curve crossings; the small gap from $1.86$ is the dilute-solution approximation). Switch the solvent to benzene with the non-electrolyte: the same molality now shifts the freezing point by $5.12\ \mathrm{K}$ per mol kg⁻¹ — the constants belong to the solvent.
Interactive 1 — Boiling and Freezing Lab: Vapour-Pressure Curves

Two close-ups of the vapour-pressure diagram. Left: near the freezing point — the pure liquid solvent (grey dashed), the solution (red) and the solid solvent (blue); freezing happens where the liquid curve meets the solid curve. Right: near the boiling point — boiling happens where the curve reaches the $1\ \mathrm{atm}$ line (purple). Choose the solvent, the solute (its van't Hoff factor $i$) and the molality; the solution curve is drawn from Raoult's law, $p=x_1p^\circ$. Play sweeps a thermometer through both panels.

0.30 mol/kg
$\Delta T_b=iK_bm$—
$\Delta T_f=iK_fm$—
boils at (1 atm)—
freezes at—

Solutions of urea, each of molality $0.10\ \mathrm{mol\,kg^{-1}}$, are made in water ($K_b=0.52$) and in benzene ($K_b=2.53\ \mathrm{K\,kg\,mol^{-1}}$). Which statement is correct?

Osmosis and osmotic pressure

Tie a piece of animal bladder or a cellophane sheet over the mouth of a thistle funnel, fill the funnel with sugar solution and dip it into pure water. Over hours the liquid in the funnel's stem climbs, sometimes by tens of centimetres. Water has passed into the solution through the membrane, while the sugar has not passed out. The membrane lets small solvent molecules through but blocks the solute — it is semipermeable.

📘 Definition 5.12 — Semipermeable membrane, osmosis and osmotic pressure

A semipermeable membrane (SPM) is a film that allows solvent molecules to pass but not solute particles. Natural examples are cell membranes and animal bladders; artificial ones are cellophane, parchment, cellulose acetate and a gelatinous precipitate of copper(II) hexacyanidoferrate(II) deposited in the walls of a porous pot.

Osmosis is the spontaneous net flow of solvent through a semipermeable membrane from the pure solvent into a solution (or from a more dilute solution into a more concentrated one).

The osmotic pressure $\pi$ of a solution is the excess pressure that must be applied to the solution to just stop osmosis when it is separated from the pure solvent by a semipermeable membrane. In the thistle-funnel experiment it equals the hydrostatic pressure $h\rho g$ of the raised column once the flow has stopped.

Why the solvent moves. On each side of the membrane solvent molecules hit the pores and some pass through. On the solution side some of the "hits" are made by solute particles that cannot pass, and the solvent there has a lower escaping tendency — the same reduced escaping tendency that lowers its vapour pressure. More solvent therefore crosses into the solution than out of it. Pressing on the solution raises the escaping tendency of its solvent; at an extra pressure $\pi$ the two flows balance.

In 1887 J. H. van't Hoff noticed that the osmotic pressures measured by the botanist Wilhelm Pfeffer for sugar solutions obeyed a law of exactly the same form as the ideal-gas equation, with the solute particles playing the part of the gas molecules.

📐 Law 5.8 — The van't Hoff equation for osmotic pressure

For a dilute solution of a non-electrolyte containing $n_2$ moles of solute in a volume $V$ of solution at absolute temperature $T$:

$$\pi=\frac{n_2}{V}RT=CRT,$$

where $C$ is the molarity of the solution. With $V$ in litres and $R=0.083\ \mathrm{L\,bar\,mol^{-1}\,K^{-1}}$, $\pi$ is in bar ($R=0.0821\ \mathrm{L\,atm\,mol^{-1}\,K^{-1}}$ gives atm; $R=8.314\ \mathrm{J\,mol^{-1}\,K^{-1}}$ with $C$ in $\mathrm{mol\,m^{-3}}$ gives Pa). Since $n_2=w_2/M_2$:

$$M_2=\frac{w_2\,R\,T}{\pi\,V}.$$

Conditions: dilute solution, a membrane that is truly impermeable to the solute, and no dissociation or association of the solute (otherwise see the van't Hoff factor below). Solutions with equal molarity of solute particles at the same temperature have equal osmotic pressures.

Why it has the gas-law form. Pressing on a liquid with extra pressure $\pi$ raises the escaping tendency of each mole of its solvent by about $\pi\bar V_1$ (where $\bar V_1$ is the molar volume of the solvent). Dissolving the solute lowered it by an amount proportional to $RTx_2$ — the same lowering that appears in Result 5.6. At balance $\pi\bar V_1\approx RTx_2\approx RT\,n_2/n_1$, and since $n_1\bar V_1\approx V$ for a dilute solution, $\pi\approx n_2RT/V$. Osmotic pressure is the fourth face of one and the same effect.

The best method for big molecules. Osmotic pressure is large even for very dilute solutions: a $0.010\ \mathrm{mol\,L^{-1}}$ solution at $300\ \mathrm{K}$ has $\pi=0.25\ \mathrm{bar}$, enough to hold up a column of water $2.5$ m high, while its freezing point falls by only $0.019\ \mathrm{K}$. For polymers and proteins, whose molar masses are in the tens of thousands, a solution of a gram or so per $100$ mL contains so few moles that $\Delta T_f$ and $\Delta T_b$ are immeasurably small — but $\pi$ is still a few hundred pascals, a few centimetres of water. Osmotic pressure is measured at room temperature, so heat-sensitive biomolecules are not damaged, and it uses molarity, which is natural for solutions made up in volumetric flasks.

Property measuredMolar mass fromBest suited to
relative lowering of vapour pressure$M_2=\tfrac{w_2M_1p_1}{w_1\Delta p}$theory and exam problems; hard to measure precisely
elevation of boiling point$M_2=\tfrac{1000K_bw_2}{\Delta T_bw_1}$solutes stable at the boiling point
depression of freezing point$M_2=\tfrac{1000K_fw_2}{\Delta T_fw_1}$small organic molecules (larger $K_f$; camphor method)
osmotic pressure$M_2=\tfrac{w_2RT}{\pi V}$polymers, proteins and other macromolecules
📘 Definition 5.13 — Isotonic, hypertonic and hypotonic solutions

Two solutions that have the same osmotic pressure at a given temperature are isotonic; when they are separated by a semipermeable membrane there is no net osmosis. For non-electrolytes, isotonic solutions have equal molar concentrations ($C_1=C_2$, i.e. $\dfrac{w_1}{M_1V_1}=\dfrac{w_2}{M_2V_2}$); in general they have equal concentrations of solute particles.

Compared with a reference solution, a solution of higher osmotic pressure is hypertonic and one of lower osmotic pressure is hypotonic. Solvent flows by osmosis from the hypotonic solution into the hypertonic one.

Cells and tonicity. The fluid inside a red blood cell has an osmotic pressure of about $7.7$ bar at body temperature ($37\ ^\circ\mathrm{C}$), the same as that of a $0.9\%$ (mass/volume) sodium chloride solution — "normal saline". In an isotonic solution the cell keeps its shape. In a hypotonic solution (say $0.3\%$ NaCl, or pure water) water flows in, the cell swells and may burst (haemolysis). In a hypertonic solution ($2\%$ NaCl) water flows out and the cell shrivels (crenation). That is why intravenous fluids are made isotonic with blood. The same principle explains why a raw mango or a cucumber placed in strong brine shrinks, why salt and sugar preserve food (bacteria lose water and die), why limp flowers revive in fresh water, and why people stranded at sea must not drink seawater.

Reverse osmosis. If a pressure greater than $\pi$ is applied to the solution side, the net flow of solvent is reversed: pure solvent is squeezed out of the solution through the membrane. This is reverse osmosis. Seawater (about $0.6\ \mathrm{mol\,L^{-1}}$ NaCl) has an osmotic pressure near $30$ bar, so desalination plants pump it at $50$–$70$ bar against membranes of cellulose acetate or thin-film polyamide, which let water through but reject most dissolved ions. Household "RO" water purifiers work the same way on a small scale.

✏️ Example 5 — Weighing a protein with a column of water
A solution containing $1.26$ g of a purified protein in $200\ \mathrm{mL}$ of aqueous solution has an osmotic pressure of $2.61\ \mathrm{mbar}$ ($2.61\times10^{-3}\ \mathrm{bar}$) at $300\ \mathrm{K}$. (a) Find the molar mass of the protein ($R=0.083\ \mathrm{L\,bar\,mol^{-1}\,K^{-1}}$). (b) How high a column of solution (density $1.0\ \mathrm{g\,mL^{-1}}$, $g=9.8\ \mathrm{m\,s^{-2}}$) does this pressure support? (c) Estimate the depression of the freezing point of the same solution, and explain why osmometry is preferred.
Find the molar mass first:
(a) $M_2=\dfrac{w_2RT}{\pi V}=\dfrac{1.26\times0.083\times300}{2.61\times10^{-3}\times0.200}=6.0\times10^{4}\ \mathrm{g\,mol^{-1}}$.
(b) $\pi=2.61\times10^{-3}\ \mathrm{bar}=261\ \mathrm{Pa}$. $h=\dfrac{\pi}{\rho g}=\dfrac{261}{1000\times9.8}=0.0266\ \mathrm{m}=2.7\ \mathrm{cm}$ — easy to read on a scale.
(c) Moles of protein $=\dfrac{1.26}{6.0\times10^{4}}=2.1\times10^{-5}\ \mathrm{mol}$ in about $0.200$ kg of water: $m\approx1.05\times10^{-4}\ \mathrm{mol\,kg^{-1}}$, so $\Delta T_f=1.86\times1.05\times10^{-4}=2.0\times10^{-4}\ \mathrm{K}$.
Why osmometry A shift of $0.0002\ \mathrm{K}$ is far below what an ordinary laboratory thermometer can resolve, while $2.7$ cm of liquid is easily measured — and at room temperature the protein is not denatured.
Check Units: $\dfrac{\mathrm{g}\times\mathrm{L\,bar\,mol^{-1}\,K^{-1}}\times\mathrm{K}}{\mathrm{bar}\times\mathrm{L}}=\mathrm{g\,mol^{-1}}$ ✓.

In the osmosis cell set $C=0.15\ \mathrm{mol\,L^{-1}}$, solute NaCl ($i=2$), $T=310\ \mathrm{K}$ and applied pressure $P=0$. How does this solution compare with blood (particle concentration about $0.30\ \mathrm{mol\,L^{-1}}$)?

With $C=0.15$, $i=2$, $T=310\ \mathrm{K}$, $P=0$ the readouts show $\pi=7.72\ \mathrm{bar}$, a supported column of $78.8$ m of water, net driving pressure $\pi-P=7.72\ \mathrm{bar}$ (osmosis into the solution) and "isotonic with blood". The particle concentration is $iC=0.30\ \mathrm{mol\,L^{-1}}$ — this is roughly normal saline. Now raise $P$ to $10$ bar: $P\gt\pi$, the arrows reverse and the solution level falls — reverse osmosis squeezes water out. Set $P=7.5$: almost no net flow, because the applied pressure nearly balances $\pi$.
Interactive 2 — Osmosis Cell: Osmotic Pressure and Reverse Osmosis

A U-tube is divided by a semipermeable membrane (dashed): pure water on the left, solution on the right, and a piston that can press on the solution with pressure $P$. Small blue dots are water molecules, which can cross; red dots are solute particles, which cannot. Choose the molarity $C$, the solute, the temperature and $P$, then Play. The level difference settles where the hydrostatic head balances $\pi-P$ (heights not to scale); the bar chart compares $\pi=iCRT$ with $P$.

0.10 M300 K0.0 bar
$\pi=iCRT$—
water column held—
net $\pi-P$—
compared with blood—

Red blood cells are placed in a $0.30\%$ (mass/volume) NaCl solution. What happens?

Abnormal molar masses and the van't Hoff factor

Dissolve $0.100$ mol of sodium chloride in a kilogram of water and the freezing point falls by about $0.35\ \mathrm{K}$ — nearly twice the $0.186\ \mathrm{K}$ expected from $\Delta T_f=K_fm$. If you used the formula $M_2=1000K_fw_2/(\Delta T_fw_1)$ you would "find" a molar mass of about $31\ \mathrm{g\,mol^{-1}}$ instead of $58.5$. On the other hand, ethanoic (acetic) acid dissolved in benzene gives a freezing-point depression only a little over half the expected value and an apparent molar mass near $120\ \mathrm{g\,mol^{-1}}$, double its formula mass of $60$.

The colligative formulas are not wrong; the solute particle count is. Sodium chloride is an ionic solid that falls apart in water into $\mathrm{Na^{+}(aq)}$ and $\mathrm{Cl^{-}(aq)}$ — two particles per formula unit. Ethanoic acid molecules in benzene, a non-polar solvent that cannot hydrogen-bond to them, pair up through two hydrogen bonds into dimers, halving the particle count:

📘 Definition 5.14 — Abnormal molar mass and the van't Hoff factor

A molar mass obtained from a colligative property that differs from the true (formula) molar mass because the solute dissociates or associates in solution is called an abnormal molar mass. The van't Hoff factor $i$ measures the extent of dissociation or association:

$$i=\frac{\text{normal (formula) molar mass}}{\text{abnormal (observed) molar mass}},$$ $$i=\frac{\text{observed colligative property}}{\text{colligative property calculated for no dissociation or association}},$$ $$i=\frac{\text{total moles of solute particles after dissociation or association}}{\text{moles of solute dissolved (formula units)}}.$$

$i=1$ for a solute that stays as single molecules (glucose, urea, sucrose); $i\gt1$ for dissociation (electrolytes); $i\lt1$ for association.

📐 Result 5.9 — Colligative laws including the van't Hoff factor

For a dilute solution of a solute with van't Hoff factor $i$:

$$\frac{p_1^\circ-p_1}{p_1^\circ}=i\,x_2\ \ (\text{dilute}),\qquad \Delta T_b=i\,K_b\,m,$$ $$\Delta T_f=i\,K_f\,m,\qquad \pi=i\,C\,R\,T.$$

When a solution contains several solutes, their particles simply add: $\Delta T_f=K_f\sum i_jm_j$ and $\pi=RT\sum i_jC_j$. The product $iC$ (or $im$) is the concentration of solute particles; solutions with equal $iC$ at the same temperature are isotonic.

Now relate $i$ to the degree of dissociation $\alpha$ (the fraction of formula units that dissociate) or the degree of association $\alpha$ (the fraction of molecules that associate).

Dissociation. Let one formula unit give $n$ ions, $\mathrm{A_{x}B_{y}}\rightarrow x\,\mathrm{A^{y+}}+y\,\mathrm{B^{x-}}$ with $n=x+y$. Start with $1$ mol; $\alpha$ mol dissociate, leaving $1-\alpha$ mol undissociated and producing $n\alpha$ mol of ions. Total particles $=1-\alpha+n\alpha$.

Association. Let $n$ molecules join into one cluster, $n\,\mathrm{A}\rightleftharpoons\mathrm{A_{n}}$. Of $1$ mol, $\alpha$ mol associate, forming $\alpha/n$ mol of clusters and leaving $1-\alpha$ mol single. Total particles $=1-\alpha+\alpha/n$.

📐 Result 5.10 — The van't Hoff factor and the degree of dissociation or association

Dissociation into $n$ ions per formula unit, degree of dissociation $\alpha$:

$$i=1+(n-1)\,\alpha,\qquad \alpha=\frac{i-1}{n-1}.$$

Association of $n$ molecules into one, degree of association $\alpha$:

$$i=1-\left(1-\frac1n\right)\alpha,\qquad \alpha=\frac{1-i}{1-1/n}.$$

For complete dissociation ($\alpha=1$) $i=n$: $\mathrm{NaCl}$ and $\mathrm{KCl}$ $2$, $\mathrm{CaCl_{2}}$ and $\mathrm{K_{2}SO_{4}}$ $3$, $\mathrm{AlCl_{3}}$ and $\mathrm{K_{3}[Fe(CN)_{6}]}$ $4$, $\mathrm{Al_{2}(SO_{4})_{3}}$ and $\mathrm{K_{4}[Fe(CN)_{6}]}$ $5$ (a complex ion counts as one particle). For complete dimerisation ($n=2$, $\alpha=1$) $i=\tfrac12$.

Strong electrolytes in practice. Even a salt that is completely ionised gives an $i$ slightly below the ideal value $n$: at $0.05\ \mathrm{mol\,kg^{-1}}$ the measured $i$ is about $1.9$ for NaCl and about $1.3$ for $\mathrm{MgSO_{4}}$. Oppositely charged ions attract one another and some move about as short-lived ion pairs, which count as single particles. The effect grows with concentration and with ionic charge, and disappears on strong dilution. When a problem says "assume complete dissociation", use $i=n$; when it gives a measured $\Delta T$, the formula $\alpha=(i-1)/(n-1)$ gives an apparent degree of dissociation, which is how NEET problems treat weak and strong electrolytes alike.

Counting ions in complexes. Colligative measurements helped Alfred Werner work out the structure of coordination compounds: a solution of the compound with formula $\mathrm{CoCl_{3}\cdot6NH_{3}}$ behaves as if each formula unit gives four particles, showing it to be $\mathrm{[Co(NH_{3})_{6}]^{3+}}$ with three free $\mathrm{Cl^{-}}$ ions. Only ions outside the coordination sphere are free particles in solution.

🧭 Problem-solving strategy — Colligative-property problems
  1. Identify the property and its concentration unit: mole fraction for vapour pressure, molality (per kg of solvent) for $\Delta T_b$ and $\Delta T_f$, molarity (per L of solution) for $\pi$.
  2. Count the particles: decide $i$ — $1$ for non-electrolytes, $n$ for complete dissociation, $1+(n-1)\alpha$ or $1-(1-1/n)\alpha$ for partial dissociation or association. Add the contributions of several solutes.
  3. Choose consistent units: masses in g with the "1000", $\Delta T$ in K, $R=0.083\ \mathrm{L\,bar\,mol^{-1}\,K^{-1}}$ (or $0.0821$ for atm), $T$ in kelvin.
  4. Solve for the unknown: a temperature shift, a molar mass, $i$ or $\alpha$. For "abnormal molar mass" use $i=M_\text{normal}/M_\text{observed}$.
  5. Check: $\Delta T_f\gt\Delta T_b$ for water; $i\gt1$ for electrolytes and $i\lt1$ for associating solutes; $0\le\alpha\le1$.
✏️ Example 6 — A weak acid in water and benzoic acid in benzene
(a) A $0.100\ \mathrm{mol\,kg^{-1}}$ aqueous solution of a weak monobasic acid HA freezes at $-0.2046\ ^\circ\mathrm{C}$ ($K_f=1.86\ \mathrm{K\,kg\,mol^{-1}}$). Find $i$ and the degree of dissociation of HA. (b) $2.44$ g of benzoic acid ($\mathrm{C_{6}H_{5}COOH}$, $122\ \mathrm{g\,mol^{-1}}$) dissolved in $50.0$ g of benzene ($K_f=5.12\ \mathrm{K\,kg\,mol^{-1}}$) lowers its freezing point by $1.23\ \mathrm{K}$. Find the van't Hoff factor, the observed molar mass and the degree of association, assuming the acid forms dimers.
Find the degree of association in (b) before opening the solution:
(a) i Expected for no dissociation: $K_fm=1.86\times0.100=0.186\ \mathrm{K}$. Observed $0.2046\ \mathrm{K}$, so $i=\dfrac{0.2046}{0.186}=1.10$.
(a) α $\mathrm{HA}\rightleftharpoons\mathrm{H^{+}}+\mathrm{A^{-}}$, $n=2$: $\alpha=\dfrac{i-1}{n-1}=0.10$ — the acid is $10\%$ ionised. (Treating molality as molarity, the ionisation constant of Unit 6 would be $\dfrac{C\alpha^2}{1-\alpha}=\dfrac{0.100\times0.010}{0.90}=1.1\times10^{-3}$.)
(b) i $m=\dfrac{2.44/122}{0.0500}=0.400\ \mathrm{mol\,kg^{-1}}$; expected $\Delta T_f=5.12\times0.400=2.048\ \mathrm{K}$; $i=\dfrac{1.23}{2.048}=0.60$.
(b) M and α Observed molar mass $=\dfrac{122}{0.60}=203\ \mathrm{g\,mol^{-1}}$ (directly: $\dfrac{1000\times5.12\times2.44}{1.23\times50.0}=203$). Dimers: $i=1-\tfrac{\alpha}{2}$, so $\alpha=2(1-0.60)=0.80$ — $80\%$ of the molecules are paired.
Check Particles per mole dissolved: $0.20$ single $+\,0.40$ dimers $=0.60$ ✓; and $122\lt203\lt244$, between the monomer and the full dimer.
✏️ Example 7 — NEET style: one solution, two colligative properties
An aqueous solution of glucose freezes at $-0.372\ ^\circ\mathrm{C}$. At $1$ atm the same solution boils at ($K_f=1.86$, $K_b=0.52\ \mathrm{K\,kg\,mol^{-1}}$) (A) $100.372\ ^\circ\mathrm{C}$ (B) $100.104\ ^\circ\mathrm{C}$ (C) $101.33\ ^\circ\mathrm{C}$ (D) $100.052\ ^\circ\mathrm{C}$
Eliminate first (10 s) Both shifts are proportional to the same $i\,m$ (Result 5.7), and for water $K_b\lt K_f$, so $\Delta T_b$ must be smaller than $\Delta T_f=0.372$ K. Options (A) ($\Delta T_b=0.372$ K) and (C) ($1.33$ K) are out.
Ratio $\dfrac{\Delta T_b}{\Delta T_f}=\dfrac{K_b}{K_f}$, so $\Delta T_b=0.372\times\dfrac{0.52}{1.86}=0.104$ K.
Check through the molality $m=\dfrac{0.372}{1.86}=0.200\ \mathrm{mol\,kg^{-1}}$; $\Delta T_b=0.52\times0.200=0.104$ K ✓.
Answer (B) $100.104\ ^\circ\mathrm{C}$.
⏱ Shortcut You never need the molar mass of glucose or the amount of water: the ratio of two colligative properties of one solution is just the ratio of the solvent's constants. Option (C) multiplies by $\tfrac{1.86}{0.52}$ instead of dividing; (D) halves the right answer, as if glucose dimerised.
⚠️ NEET traps

1. Count particles, not atoms. $\mathrm{K_{4}[Fe(CN)_{6}]}$ gives $4\,\mathrm{K^{+}}$ and one complex ion, $i=5$ (not $11$, not $1$); $\mathrm{[Co(NH_{3})_{6}]Cl_{3}}$ gives $4$ ions; mercury(I) chloride gives the single ion $\mathrm{Hg_{2}^{2+}}$. Glucose, urea and sucrose have $i=1$; ethanoic and benzoic acids in benzene have $i$ close to $\tfrac12$.

2. Molality or molarity? $\Delta T_b$ and $\Delta T_f$ use moles per kilogram of solvent; $\pi=iCRT$ uses moles per litre of solution. "$5\%$ by mass" means $5$ g of solute in $95$ g of solvent.

3. Which way up is $i$? $i=\dfrac{\text{observed colligative property}}{\text{calculated}}=\dfrac{M_\text{normal}}{M_\text{observed}}$. An observed molar mass larger than normal means association ($i\lt1$); a smaller one means dissociation ($i\gt1$).

4. Read the direction word. The solution with the largest $i\,m$ has the lowest freezing point and vapour pressure but the highest boiling point and osmotic pressure. "Highest freezing point" therefore asks for the smallest $i\,m$.

5. $K_b$ and $K_f$ belong to the solvent. They do not depend on the solute; their unit is $\mathrm{K\,kg\,mol^{-1}}$. For water $K_f=1.86$ is larger than $K_b=0.52$, so a solution freezes further below $0\ ^\circ\mathrm{C}$ than it boils above $100\ ^\circ\mathrm{C}$; for benzene $K_f=5.12$ and $K_b=2.53$.

6. Units of $R$ and $T$. With $C$ in $\mathrm{mol\,L^{-1}}$ use $R=0.083\ \mathrm{L\,bar}$ or $0.0821\ \mathrm{L\,atm\,mol^{-1}\,K^{-1}}$ and $T$ in kelvin. A temperature difference is the same in K and in °C.

7. Osmosis and cells. Solvent flows through the membrane from the dilute side (or pure solvent) into the concentrated side. Red blood cells are isotonic with about $0.9\%$ NaCl: in a weaker (hypotonic) solution they swell and may burst; in a stronger (hypertonic) one they shrink. Reverse osmosis needs a pressure greater than $\pi$ applied to the solution side.

8. Lowering versus relative lowering. The relative lowering $\dfrac{p_{1}^{\circ}-p_{1}}{p_{1}^{\circ}}$ equals $x_{2}$, the mole fraction of the solute, and is colligative; the vapour pressure of the solution itself, and even the lowering $\Delta p_{1}$, depend on the solvent.

Assuming complete dissociation, the van't Hoff factor of potassium hexacyanidoferrate(II), $\mathrm{K_{4}[Fe(CN)_{6}]}$, in water is

Exercises

Unless stated otherwise, for water take $K_f=1.86$ and $K_b=0.52\ \mathrm{K\,kg\,mol^{-1}}$; for benzene $K_f=5.12$ and $K_b=2.53\ \mathrm{K\,kg\,mol^{-1}}$; $R=0.083\ \mathrm{L\,bar\,mol^{-1}\,K^{-1}}$. Molar masses: H 1, C 12, N 14, O 16, Na 23, S 32, Cl 35.5, K 39, Ca 40.

I
Colligative properties and the relative lowering of vapour pressure.
  • 1 Find the relative lowering of vapour pressure of a solution of $6.0$ g of urea ($60\ \mathrm{g\,mol^{-1}}$) in $90$ g of water.
  • 2 The vapour pressure of pure water at $25\ ^\circ\mathrm{C}$ is $3.17\ \mathrm{kPa}$. Find the vapour pressure of the solution in part 1.
  • 3 The vapour pressure of an aqueous glucose solution is $98.0\%$ of that of pure water at the same temperature. Find the mole fraction of glucose and the molality of the solution.
  • 4 At a certain temperature pure benzene has a vapour pressure of $95.0\ \mathrm{mm\,Hg}$. A solution of $10.0$ g of a non-volatile non-electrolyte in $100$ g of benzene has a vapour pressure of $92.13\ \mathrm{mm\,Hg}$. Find the molar mass of the solute using the exact relation.
  • 5 What mass of sucrose ($342\ \mathrm{g\,mol^{-1}}$) must be dissolved in $180$ g of water to lower its vapour pressure by exactly $1.0\%$?
  • 6 Show that for a dilute solution $\dfrac{\Delta p_1}{p_1^\circ}\approx\dfrac{mM_1}{1000}$, and use it to find the relative lowering for a $0.50\ \mathrm{mol\,kg^{-1}}$ aqueous solution.
  • 7 Explain why the relative lowering $\Delta p_1/p_1^\circ$ is a colligative property while the lowering $\Delta p_1$ itself, for the same mole fraction of solute, is different in different solvents.
  • 8 $10$ g each of urea ($60$) and glucose ($180$) are dissolved separately in $100$ g of water. Find the ratio of their relative lowerings of vapour pressure, exactly and approximately.
1 $n_2=0.10$, $n_1=5.0\ \mathrm{mol}$: $\dfrac{\Delta p}{p^\circ}=x_2=\dfrac{0.10}{5.10}=0.0196$.
2 $p=p^\circ(1-x_2)=3.17\times0.9804=3.11\ \mathrm{kPa}$.
3 $x_2=1-0.980=0.020$. Per mole of solution: $0.020$ mol glucose in $0.980$ mol ($17.64$ g) of water, so $m=\dfrac{0.020}{0.01764}=1.13\ \mathrm{mol\,kg^{-1}}$.
4 $n_1=\dfrac{100}{78}=1.282\ \mathrm{mol}$; $\dfrac{\Delta p}{p}=\dfrac{2.87}{92.13}=0.03115=\dfrac{n_2}{n_1}$, so $n_2=0.03994\ \mathrm{mol}$ and $M_2=\dfrac{10.0}{0.03994}=250\ \mathrm{g\,mol^{-1}}$. (The dilute form would give $258$.)
5 $n_1=10.0\ \mathrm{mol}$. $x_2=0.010$ means $\dfrac{n_2}{n_2+10.0}=0.010$, so $n_2=\dfrac{10.0}{99}=0.101\ \mathrm{mol}$ and the mass is $0.101\times342=34.5$ g. (The dilute form $n_2\approx0.010\times10.0$ gives $34.2$ g.)
6 Dilute: $x_2\approx\dfrac{n_2}{n_1}=\dfrac{m\times(w_1/1000)}{w_1/M_1}=\dfrac{mM_1}{1000}$. For $m=0.50$: $\dfrac{0.50\times18}{1000}=0.0090$ (exact $x_2=\dfrac{0.50}{0.50+55.5}=0.0089$).
7 $\Delta p_1=x_2p_1^\circ$: the relative lowering $x_2$ depends only on the proportion of solute particles, but the absolute lowering is that fraction of the solvent's own vapour pressure, so a volatile solvent (large $p_1^\circ$, e.g. ether) shows a larger $\Delta p_1$ than water for the same $x_2$.
8 Urea: $n_2=0.1667$, $x_2=\dfrac{0.1667}{5.556+0.1667}=0.0291$. Glucose: $n_2=0.0556$, $x_2=\dfrac{0.0556}{5.611}=0.00990$. Ratio $=2.94$; approximately the inverse ratio of molar masses, $180/60=3$.
II
Elevation of boiling point and depression of freezing point.
  • 1 Find the boiling point and the freezing point of a solution of $9.0$ g of glucose ($180\ \mathrm{g\,mol^{-1}}$) in $250$ g of water at $1\ \mathrm{atm}$.
  • 2 $1.00$ g of a non-electrolyte dissolved in $50.0$ g of benzene lowers its freezing point by $0.40\ \mathrm{K}$. Find the molar mass of the solute.
  • 3 Pure benzene boils at $80.10\ ^\circ\mathrm{C}$. Find the boiling point of a solution of $2.56$ g of naphthalene ($\mathrm{C_{10}H_{8}}$) in $100$ g of benzene.
  • 4 What mass of ethylene glycol ($62\ \mathrm{g\,mol^{-1}}$) must be added to $2.0$ kg of water so that the solution does not freeze above $-6.0\ ^\circ\mathrm{C}$?
  • 5 For any dilute aqueous solution of a non-electrolyte, find the ratio $\Delta T_f/\Delta T_b$. If such a solution freezes at $-0.93\ ^\circ\mathrm{C}$, at what temperature does it boil?
  • 6 Calculate $K_b$ for water from $\Delta_{vap}H=40.7\ \mathrm{kJ\,mol^{-1}}$ at $373\ \mathrm{K}$ ($R=8.314\ \mathrm{J\,mol^{-1}\,K^{-1}}$, $M_1=18\ \mathrm{g\,mol^{-1}}$).
  • 7 A $2.0\%$ (by mass) aqueous solution of a non-electrolyte freezes at $-0.632\ ^\circ\mathrm{C}$. Find the molar mass of the solute and suggest what it might be.
  • 8 In the camphor method, $10.0$ mg of an organic compound melted with $1.00$ g of camphor ($K_f=40\ \mathrm{K\,kg\,mol^{-1}}$) lowers the melting point by $2.0\ \mathrm{K}$. Find its molar mass, and explain why camphor is used.
  • 9 Explain, using vapour-pressure curves, why a solution freezes at a lower temperature than the solvent, and why the formula $\Delta T_f=K_fm$ fails if the solute crystallises together with the solvent.
1 $m=\dfrac{0.050}{0.250}=0.20\ \mathrm{mol\,kg^{-1}}$. $\Delta T_b=0.52\times0.20=0.104\ \mathrm{K}$: boils at $100.104\ ^\circ\mathrm{C}$. $\Delta T_f=1.86\times0.20=0.372\ \mathrm{K}$: freezes at $-0.372\ ^\circ\mathrm{C}$.
2 $M_2=\dfrac{1000\times5.12\times1.00}{0.40\times50.0}=256\ \mathrm{g\,mol^{-1}}$.
3 $M(\mathrm{C_{10}H_{8}})=128$; $m=\dfrac{2.56/128}{0.100}=0.200\ \mathrm{mol\,kg^{-1}}$; $\Delta T_b=2.53\times0.200=0.506\ \mathrm{K}$; boils at $80.61\ ^\circ\mathrm{C}$.
4 $m=\dfrac{6.0}{1.86}=3.23\ \mathrm{mol\,kg^{-1}}$; $n=6.45\ \mathrm{mol}$; mass $=6.45\times62=400$ g.
5 $\dfrac{\Delta T_f}{\Delta T_b}=\dfrac{K_f}{K_b}=\dfrac{1.86}{0.52}=3.58$. $m=\dfrac{0.93}{1.86}=0.50$, so $\Delta T_b=0.26\ \mathrm{K}$: boils at $100.26\ ^\circ\mathrm{C}$.
6 $K_b=\dfrac{8.314\times373^2\times18}{1000\times40\,700}=0.512\ \mathrm{K\,kg\,mol^{-1}}$.
7 $2.0$ g solute in $98.0$ g water: $M_2=\dfrac{1000\times1.86\times2.0}{0.632\times98.0}=60\ \mathrm{g\,mol^{-1}}$ — consistent with urea, $\mathrm{CO(NH_{2})_{2}}$ (or ethanoic acid, but that would ionise slightly).
8 $M_2=\dfrac{1000\times40\times0.0100}{2.0\times1.00}=200\ \mathrm{g\,mol^{-1}}$. Camphor's huge $K_f$ turns a few milligrams of sample into a depression of several kelvin, readable with an ordinary thermometer, and it dissolves most organic compounds when molten.
9 At the freezing point the liquid and the solid solvent have equal vapour pressures. The solute lowers the liquid's curve but not the pure solid's, so the curves now cross at a lower temperature. If the solute enters the solid (a solid solution forms), the solid's vapour pressure is lowered too, and the simple shift $K_fm$ no longer applies (the freezing point may even rise).
III
Osmotic pressure, tonicity and reverse osmosis.
  • 1 Find the osmotic pressure of a $0.050\ \mathrm{mol\,L^{-1}}$ glucose solution at $27\ ^\circ\mathrm{C}$.
  • 2 A solution of $2.0$ g of a polymer in $250\ \mathrm{mL}$ of solution has an osmotic pressure of $1.66\times10^{-3}\ \mathrm{bar}$ at $300\ \mathrm{K}$. Find the molar mass of the polymer.
  • 3 A $1.8\%$ (mass/volume) glucose solution is isotonic with a urea solution. Find the mass/volume percentage of urea.
  • 4 The osmotic pressure of blood is $7.7$ bar at $310\ \mathrm{K}$. Assuming complete dissociation, find the mass/volume percentage of NaCl that is isotonic with blood.
  • 5 Predict and explain what happens to red blood cells placed in (a) $0.3\%$ NaCl and (b) $2\%$ NaCl solution.
  • 6 Treating seawater as $0.60\ \mathrm{mol\,L^{-1}}$ NaCl (fully dissociated) at $298\ \mathrm{K}$, find the minimum pressure needed to desalinate it by reverse osmosis.
  • 7 A $0.10\ \mathrm{mol\,L^{-1}}$ glucose solution (A) and a $0.10\ \mathrm{mol\,L^{-1}}$ NaCl solution (B) are separated by a semipermeable membrane. In which direction does water flow, and which solution is hypertonic?
  • 8 $1.0$ g of a protein of molar mass $50\,000\ \mathrm{g\,mol^{-1}}$ is dissolved to make $100\ \mathrm{mL}$ of solution at $300\ \mathrm{K}$. Find its osmotic pressure in pascals and the height of the water column it supports ($\rho=1000\ \mathrm{kg\,m^{-3}}$, $g=9.8\ \mathrm{m\,s^{-2}}$).
1 $\pi=CRT=0.050\times0.083\times300=1.245\ \mathrm{bar}$, about $1.2\ \mathrm{bar}$.
2 $M=\dfrac{wRT}{\pi V}=\dfrac{2.0\times0.083\times300}{1.66\times10^{-3}\times0.250}=1.2\times10^{5}\ \mathrm{g\,mol^{-1}}$.
3 Glucose: $\dfrac{18\ \mathrm{g\,L^{-1}}}{180}=0.10\ \mathrm{mol\,L^{-1}}$. Urea at $0.10\ \mathrm{mol\,L^{-1}}$ is $6.0\ \mathrm{g\,L^{-1}}$, i.e. $0.60\%$.
4 $iC=\dfrac{7.7}{0.083\times310}=0.299\ \mathrm{mol\,L^{-1}}$; with $i=2$, $C=0.150\ \mathrm{mol\,L^{-1}}$ $=0.150\times58.5=8.75\ \mathrm{g\,L^{-1}}$, i.e. $0.875\%$ — close to the $0.9\%$ of normal saline.
5 (a) $0.3\%$ is hypotonic: water enters, the cells swell and may burst (haemolysis). (b) $2\%$ is hypertonic: water leaves, the cells shrink (crenation).
6 $\pi=iCRT=2\times0.60\times0.083\times298=29.7\ \mathrm{bar}$; any pressure above this reverses osmosis (plants use about twice as much to get a useful flow rate).
7 Particle concentrations: A $0.10$, B $2\times0.10=0.20\ \mathrm{mol\,L^{-1}}$. B is hypertonic; water flows from A into B.
8 $C=\dfrac{1.0/50\,000}{0.100}=2.0\times10^{-4}\ \mathrm{mol\,L^{-1}}=0.20\ \mathrm{mol\,m^{-3}}$. $\pi=0.20\times8.314\times300=499\ \mathrm{Pa}$ (with $R=0.083$: $4.98\times10^{-3}\ \mathrm{bar}=498\ \mathrm{Pa}$). $h=\dfrac{499}{1000\times9.8}=0.051\ \mathrm{m}=5.1\ \mathrm{cm}$.
IV
The van't Hoff factor and abnormal molar masses.
  • 1 Assuming complete dissociation, write $i$ for $\mathrm{K_{2}SO_{4}}$, $\mathrm{K_{3}[Fe(CN)_{6}]}$, $\mathrm{[Co(NH_{3})_{6}]Cl_{3}}$ and $\mathrm{Al_{2}(SO_{4})_{3}}$.
  • 2 A $0.10\ \mathrm{mol\,kg^{-1}}$ aqueous solution of $\mathrm{CaCl_{2}}$ freezes at $-0.48\ ^\circ\mathrm{C}$. Find $i$ and the apparent degree of dissociation.
  • 3 Arrange in order of increasing boiling point: $0.10\ \mathrm{mol\,kg^{-1}}$ sucrose, $0.10\ \mathrm{mol\,kg^{-1}}$ KCl, $0.05\ \mathrm{mol\,kg^{-1}}$ $\mathrm{MgCl_{2}}$ (complete dissociation).
  • 4 A $0.20\ \mathrm{mol\,kg^{-1}}$ aqueous solution of a weak monobasic acid freezes at $-0.4464\ ^\circ\mathrm{C}$. Find the percentage dissociation of the acid.
  • 5 Ethanoic acid ($60\ \mathrm{g\,mol^{-1}}$) in benzene shows an observed molar mass of $114\ \mathrm{g\,mol^{-1}}$. Find $i$ and the degree of association (dimers).
  • 6 Find the osmotic pressure of a $0.050\ \mathrm{mol\,L^{-1}}$ $\mathrm{K_{2}SO_{4}}$ solution at $300\ \mathrm{K}$, assuming complete dissociation.
  • 7 The molar mass of NaCl found from the freezing point of a dilute aqueous solution is $31.5\ \mathrm{g\,mol^{-1}}$. Find $i$ and the apparent degree of dissociation.
  • 8 A $0.020\ \mathrm{mol\,kg^{-1}}$ aqueous solution of the complex $\mathrm{CoCl_{3}\cdot4NH_{3}}$ freezes at $-0.0744\ ^\circ\mathrm{C}$. How many particles does each formula unit give, and what is the structural formula of the complex (cobalt is six-coordinate)?
  • 9 A solution contains $0.010$ mol of NaCl and $0.020$ mol of glucose in $500$ g of water. Find its freezing point, assuming NaCl is fully dissociated.
1 $\mathrm{K_{2}SO_{4}}$: $2\,\mathrm{K^{+}}+\mathrm{SO_{4}^{2-}}$, $i=3$. $\mathrm{K_{3}[Fe(CN)_{6}]}$: $3\,\mathrm{K^{+}}+\mathrm{[Fe(CN)_{6}]^{3-}}$, $i=4$. $\mathrm{[Co(NH_{3})_{6}]Cl_{3}}$: $\mathrm{[Co(NH_{3})_{6}]^{3+}}+3\,\mathrm{Cl^{-}}$, $i=4$. $\mathrm{Al_{2}(SO_{4})_{3}}$: $2\,\mathrm{Al^{3+}}+3\,\mathrm{SO_{4}^{2-}}$, $i=5$.
2 $i=\dfrac{0.48}{1.86\times0.10}=2.58$; $n=3$, so $\alpha=\dfrac{2.58-1}{2}=0.79$.
3 $im$: sucrose $0.10$, $\mathrm{MgCl_{2}}$ $0.15$, KCl $0.20$. Increasing boiling point: sucrose $\lt$ $\mathrm{MgCl_{2}}$ $\lt$ KCl.
4 $i=\dfrac{0.4464}{1.86\times0.20}=1.20$; $\alpha=\dfrac{i-1}{2-1}=0.20$, i.e. $20\%$.
5 $i=\dfrac{60}{114}=0.526$; $\alpha=\dfrac{1-i}{1-\tfrac12}=2(1-0.526)=0.947$ — almost $95\%$ dimerised.
6 $\pi=iCRT=3\times0.050\times0.083\times300=3.74\ \mathrm{bar}$.
7 $i=\dfrac{58.5}{31.5}=1.86$; $\alpha=\dfrac{1.86-1}{1}=0.86$, an apparent $86\%$ (the "missing" $14\%$ reflects ion-pairing, not true non-dissociation).
8 $i=\dfrac{0.0744}{1.86\times0.020}=2.0$: two particles, one complex cation and one $\mathrm{Cl^{-}}$. With six-coordinate cobalt, four $\mathrm{NH_{3}}$ and two $\mathrm{Cl}$ are ligands: $\mathrm{[Co(NH_{3})_{4}Cl_{2}]Cl}$.
9 Particles: $2\times0.010+0.020=0.040\ \mathrm{mol}$ in $0.500$ kg, i.e. $0.080\ \mathrm{mol\,kg^{-1}}$. $\Delta T_f=1.86\times0.080=0.149\ \mathrm{K}$; freezes at $-0.149\ ^\circ\mathrm{C}$.
🎯 Exam corner NEET · MCQ

Six original problems in the NEET style — one correct option each, marked $+4$ / $-1$ / $0$. For water use $K_f=1.86$ and $K_b=0.52\ \mathrm{K\,kg\,mol^{-1}}$; take $R=0.083\ \mathrm{L\,bar\,mol^{-1}\,K^{-1}}$. Aim for about a minute per problem; the ⏱ steps show the fast route.

E1. NEET · MCQ Given below are two statements. Statement I: Assuming complete dissociation, the osmotic pressure of $0.10\ \mathrm{M}$ NaCl at $300$ K is twice that of $0.10\ \mathrm{M}$ glucose at the same temperature. Statement II: In reverse osmosis, water passes from a concentrated solution into a dilute one when a pressure smaller than the osmotic pressure is applied to the concentrated side. Choose the correct answer. (A) Both Statement I and Statement II are true (B) Both Statement I and Statement II are false (C) Statement I is true but Statement II is false (D) Statement I is false but Statement II is true

Statement I $\pi=iCRT$ (Result 5.9): NaCl has $i=2$, glucose $i=1$, with the same $C$ and $T$. True.
Statement II A pressure smaller than $\pi$ only slows ordinary osmosis, which still carries water into the concentrated solution. The flow reverses only when the applied pressure exceeds $\pi$ (Definition 5.12). False.
Answer (C).
⏱ Shortcut In osmosis questions look for the words "greater" and "smaller": the osmotic pressure is the exact pressure at which nothing flows, so reversal always needs more than $\pi$.

E2. NEET · MCQ Assertion (A): The molar mass of ethanoic acid found from the depression of the freezing point of its solution in benzene is nearly twice its formula mass of $60\ \mathrm{g\,mol^{-1}}$. Reason (R): In benzene, ethanoic acid molecules pair up into dimers held together by two hydrogen bonds. (A) Both A and R are true and R is the correct explanation of A (B) Both A and R are true but R is not the correct explanation of A (C) A is true but R is false (D) A is false but R is true

Reason True: in a non-polar solvent the $-\mathrm{COOH}$ groups of two molecules hydrogen-bond to each other, forming $\mathrm{(CH_{3}COOH)_{2}}$.
Assertion and link Dimerisation halves the number of particles, $i\approx\tfrac12$, so $\Delta T_f$ is about half the expected value and the "observed" molar mass, $M_\text{normal}/i$, comes out near $120\ \mathrm{g\,mol^{-1}}$ (Result 5.10). R is the cause of A.
Answer (A).

E3. NEET · MCQ Match List-I (compound, completely dissociated in water) with List-II (van't Hoff factor $i$).
List-I: P. $\mathrm{K_{4}[Fe(CN)_{6}]}$ · Q. $\mathrm{[Co(NH_{3})_{5}Cl]Cl_{2}}$ · R. $\mathrm{Al(NO_{3})_{3}}$ · S. $\mathrm{MgSO_{4}}$
List-II: I. $2$ · II. $3$ · III. $4$ · IV. $5$
Choose the correct answer. (A) P-IV, Q-III, R-II, S-I (B) P-IV, Q-II, R-III, S-I (C) P-II, Q-IV, R-III, S-I (D) P-IV, Q-II, R-I, S-III

Count the free ions P: $4\,\mathrm{K^{+}}+\mathrm{[Fe(CN)_{6}]^{4-}}$, $i=5$ (IV). Q: only the two chlorides outside the bracket are free, $\mathrm{[Co(NH_{3})_{5}Cl]^{2+}}+2\,\mathrm{Cl^{-}}$, $i=3$ (II). R: $\mathrm{Al^{3+}}+3\,\mathrm{NO_{3}^{-}}$, $i=4$ (III). S: $\mathrm{Mg^{2+}}+\mathrm{SO_{4}^{2-}}$, $i=2$ (I).
Answer (B) P-IV, Q-II, R-III, S-I.
⏱ Shortcut Option (A) counts the chlorine inside the coordination sphere as a free ion. A ligand inside the square bracket never leaves it in solution — that is how colligative measurements revealed the structures of such complexes.

E4. NEET · MCQ The graph shows the vapour pressure of pure water and of an aqueous solution of a non-volatile non-electrolyte near $100\ ^\circ\mathrm{C}$. The horizontal dashed line is the external pressure, $1$ atm. The freezing point of the same solution is (A) $-0.52\ ^\circ\mathrm{C}$ (B) $-0.93\ ^\circ\mathrm{C}$ (C) $-3.72\ ^\circ\mathrm{C}$ (D) $-1.86\ ^\circ\mathrm{C}$ 99.6100.00100.52100.8temperature / °C 99100101102103 vapour pressure / kPa 101.3 kPa pure watersolution

Read the graph A liquid boils where its vapour pressure reaches the external pressure. Water does so at $100.00\ ^\circ\mathrm{C}$, the solution — whose vapour pressure is lower at every temperature — at $100.52\ ^\circ\mathrm{C}$. So $\Delta T_b=0.52$ K.
Molality $m=\dfrac{\Delta T_b}{K_b}=\dfrac{0.52}{0.52}=1.0\ \mathrm{mol\,kg^{-1}}$ (Result 5.7).
Freezing point $\Delta T_f=K_fm=1.86$ K, so the solution freezes at $-1.86\ ^\circ\mathrm{C}$.
Answer (D) $-1.86\ ^\circ\mathrm{C}$.
⏱ Shortcut $\Delta T_f=\Delta T_b\times\dfrac{K_f}{K_b}$. Option (A) copies $\Delta T_b$ as if $K_f$ were equal to $K_b$; (C) doubles the answer, as if the solute were an electrolyte with $i=2$ — but the same $i$ appears in both laws and cancels.

E5. NEET · MCQ How many of the following statements are correct? (i) The relative lowering of the vapour pressure of a solution equals the mole fraction of the solute. (ii) The cryoscopic constant $K_f$ of a solvent depends on the nature of the solute. (iii) $0.10\ \mathrm{M}$ NaCl and $0.10\ \mathrm{M}$ glucose are isotonic at the same temperature. (iv) Red blood cells placed in $0.50\%$ (mass/volume) NaCl solution swell. (v) Osmotic pressure is the preferred colligative property for finding the molar masses of proteins and polymers. (vi) $\Delta T_b$ for a $1.0\ \mathrm{mol\,kg^{-1}}$ aqueous solution of urea is $0.52$ K. (vii) Desalination by reverse osmosis needs a pressure greater than the osmotic pressure of seawater. (viii) Association of solute molecules increases the observed depression of freezing point. (A) $5$ (B) $4$ (C) $6$ (D) $3$

Correct (i) ✓ (Result 5.6); (iv) ✓ — $0.50\%$ is hypotonic to blood (about $0.9\%$), so water enters the cells (Definition 5.13); (v) ✓ — large, easily measured at room temperature; (vi) ✓ — $\Delta T_b=K_bm$ with $i=1$; (vii) ✓.
Wrong (ii) $K_f$ is a property of the solvent alone; (iii) NaCl gives twice as many particles, so it is hypertonic to the glucose; (viii) association reduces the number of particles and so the observed $\Delta T_f$.
Answer (A) $5$.
⏱ Shortcut Tick or cross each statement in the margin as you go; with eight statements, counting in your head is where marks are lost.

E6. NEET · MCQ A $0.10\ \mathrm{M}$ aqueous solution of a weak monobasic acid HA is $20\%$ dissociated at $300$ K. Its osmotic pressure is (A) $2.49$ bar (B) $4.98$ bar (C) $2.99$ bar (D) $0.30$ bar

van't Hoff factor $\mathrm{HA\rightleftharpoons H^{+}+A^{-}}$, $n=2$: $i=1+(n-1)\alpha=1+0.20=1.20$ (Result 5.10).
Osmotic pressure $\pi=iCRT=1.20\times0.10\times0.083\times300=2.99$ bar (Result 5.9).
Answer (C) $2.99$ bar.
⏱ Shortcut $CRT=0.10\times0.083\times300=2.49$ bar is option (A) — the value with $i=1$. A weak acid must give a little more, never twice as much (B, which assumes complete dissociation). So the answer lies just above $2.49$: $2.49\times1.2=2.99$.
🔬 Research–Teaching NexusResearch-tutored · optional, about 60 minutes

Research question. What is the osmotic pressure of the sap inside potato cells — and is it closer to that of blood, of seawater, or of a sports drink?

Why it matters. Every living cell controls its water by osmosis. Hospitals in every country must make intravenous fluids isotonic with blood; farmers irrigating with slightly salty groundwater (as in parts of Rajasthan, Australia and California) see crops wilt when the soil water becomes hypertonic to the roots; food scientists use brines and syrups to draw water out of microbes. Plant physiologists measure tissue "water potential" by the simple method below.

What to do.

  1. Make sucrose solutions of $0$, $0.1$, $0.2$, $0.3$, $0.4$, $0.5$ and $0.6\ \mathrm{mol\,L^{-1}}$ ($34.2$ g of sugar per $100\ \mathrm{mL}$ is $1.0\ \mathrm{mol\,L^{-1}}$; dilute from it).
  2. Cut equal cylinders or strips of raw potato (about $4$ cm long), blot them and weigh each to $0.01$ g on a kitchen scale.
  3. Leave three strips in each solution for at least $45$ minutes at room temperature, then blot and re-weigh.
  4. Plot the percentage change in mass against the sucrose concentration. Read off the concentration $C_0$ at which the mass does not change — the solution isotonic with the cell sap.
  5. Calculate the osmotic pressure of the sap, $\pi=C_0RT$, and compare it with blood ($7.7$ bar) and seawater (about $28$ bar).

Tools: Potatoes, a cork borer or knife, sugar, measuring cylinder, kitchen scale (0.01 g), thermometer, a spreadsheet for the graph.

Hand in: Your table of masses, the graph with the interpolated $C_0$, the osmotic pressure with units and an estimate of its uncertainty, and one paragraph explaining what happened to the strips in the strongest and weakest solutions in terms of osmosis.

Going further. Repeat with sodium chloride solutions. Using the van't Hoff factor, predict the NaCl concentration that should be isotonic with the sap, and test the prediction. Does $i\approx2$ hold, or does the membrane let some NaCl through?

Instructor note: potato tuber cells typically give $C_0\approx0.25$–$0.35\ \mathrm{mol\,L^{-1}}$ sucrose, i.e. $\pi\approx6$–$9$ bar at room temperature, close to blood. Results scatter by $\pm0.05\ \mathrm{mol\,L^{-1}}$; triplicates and careful blotting matter more than precise timing. With NaCl the isotonic point is usually near $0.15\ \mathrm{mol\,L^{-1}}$, supporting $i\approx2$, though slow leakage of ions can blur the result over long soaks.

🧪 Self-check quiz

0/5 correct

Q1. A colligative property of a dilute solution depends on

Q2. Assuming complete dissociation of the salts, which aqueous solution has the highest boiling point?

Q3. The molar mass of a newly isolated protein is best determined from measurements of

Q4. Barium chloride is $80\%$ dissociated in a dilute aqueous solution. Its van't Hoff factor is

Q5. Which of the following is not a colligative property?