Chapter 14 ยท Introduction

Chapter 14 โ€” Electromagnetic Induction and Alternating Currents

A changing magnetic flux drives an emf round a circuit. From that single fact come Lenz's law, motional emf, eddy currents, self- and mutual inductance, the AC generator, the behaviour of R, L and C on alternating current, resonance and the transformer.

In 1831 Michael Faraday wound two coils on an iron ring, connected one to a battery and the other to a galvanometer, and saw the needle kick โ€” but only at the instant he closed or opened the switch. A steady current in the first coil did nothing to the second; a changing one drove a current through it. That flicker of a needle is the reason you can read this page. Every power station spins coils in magnetic fields to generate an alternating voltage; transformers step it up to hundreds of kilovolts for the transmission lines and down again to $230\ \text{V}$ for your home; induction cooktops heat a steel pan with currents induced inside the pan itself; and metro trains brake by turning their motors into generators.

The chapter begins with Faraday's law, $\varepsilon=-N\dfrac{d\Phi_B}{dt}$: an emf appears whenever the magnetic flux through a circuit changes โ€” because the field changes, the area changes, or the coil turns. The minus sign is Lenz's law: the induced current always opposes the change that causes it, which is energy conservation in disguise. A rod moving through a field carries a motional emf $Blv$. Changing currents induce currents in lumps of metal (eddy currents), in a neighbouring coil (mutual inductance $M$) and in their own coil (self-inductance $L$, storing energy $\tfrac12LI^2$). A coil rotating in a field gives an alternating emf $NBA\omega\sin\omega t$; on AC, an inductor and a capacitor oppose the current through reactances $\omega L$ and $\dfrac{1}{\omega C}$, a series LCR circuit has impedance $Z$ and resonates at $\omega_0=\dfrac{1}{\sqrt{LC}}$, only the resistance takes power, $V_\text{rms}I_\text{rms}\cos\phi$, and the transformer trades voltage for current.

These ideas reach well beyond the power station. An MRI scanner picks up its image signal as a tiny emf induced in receiver coils by the precessing magnetic moments of hydrogen nuclei in the body; transcranial magnetic stimulation uses a pulsed coil held against the scalp to induce currents in the brain tissue beneath it; a cochlear implant receives its power and its sound signal through the skin by mutual induction between a coil worn outside and a coil under the skin; and the induction loop laid round a hall lets a hearing aid fitted with a small pick-up coil receive the sound directly as an induced emf.

NEET sets questions on this unit every year, almost always as short MCQs: the flux through a coil and the average induced emf, the direction of an induced current by Lenz's law, the emf of a moving or rotating rod, the uses of eddy currents, the self-inductance of a solenoid and the energy $\tfrac12LI^2$, rms values, reactances, the impedance and resonance of a series LCR circuit, the power factor and the transformer. The NEET (UG) syllabus for the unit โ€” electromagnetic induction, Faraday's law, induced emf and current, Lenz's law, eddy currents, self and mutual induction; alternating currents, peak and rms values of alternating current and voltage, reactance and impedance, the series LCR circuit and resonance, power in AC circuits and wattless current, the AC generator and the transformer โ€” is covered completely by the three sections below, together with the motional emf, rotating rods and the energy stored in an inductor that NEET questions also use.

Flux $\Phi_B=BA\cos\theta$โ†’$\varepsilon=-N\tfrac{d\Phi_B}{dt}$โ†’Lenz's lawโ†’Motional emf $Blv$โ†’Eddy currentsโ†’$L$, $M$ and $\tfrac12LI^2$โ†’AC generatorโ†’rms, reactance, $Z$โ†’Resonance & powerโ†’Transformer
๐ŸŽฏ By the end of this chapter you canโ€ฆ
  • calculate magnetic flux $\Phi_B=BA\cos\theta$, and the induced emf, current and charge when it changes, $\varepsilon=-N\dfrac{d\Phi_B}{dt}$ and $q=\dfrac{N|\Delta\Phi_B|}{R}$;
  • use Lenz's law to find the direction of an induced current and explain it through conservation of energy;
  • find motional emfs โ€” $Blv$ for a sliding rod, $\tfrac12B\omega l^2$ for a rotating rod or disc โ€” and the magnetic braking force and terminal speed of a rod on rails;
  • explain eddy currents, their uses (braking, damping, induction heating) and how laminated cores reduce them;
  • find the self-inductance of a solenoid, the mutual inductance of two coils, the potential difference across an inductor and the energy $\tfrac12LI^2$ it stores;
  • derive the emf $NBA\omega\sin\omega t$ of an AC generator and use peak, rms and mean values of alternating quantities;
  • use reactance, impedance and phasors for R, L, C and series LCR circuits, and find the resonant frequency and the quality factor;
  • calculate average power, the power factor and wattless current, and solve ideal and real transformer problems;
  • solve NEET multiple-choice questions that mix all three sections in every format the paper uses โ€” single answer, statement I / II, assertionโ€“reason, matching lists, "how many are correct" and graph reading โ€” quickly, by eliminating options.

A coil of $100$ turns, each of area $0.010\ \text{m}^2$, spins in a field of $0.50\ \text{T}$ at $25$ revolutions per second. If you make it spin twice as fast ($50$ rev/s), what happens to the peak emf?

Set the frequency to $25\ \text{Hz}$ and then to $50\ \text{Hz}$. The peak flux linkage stays at $NBA=0.50\ \text{Wb}$, but the peak emf rises from $78.5\ \text{V}$ to $157.1\ \text{V}$ (rms $55.5\ \text{V}$ to $111.1\ \text{V}$), and the graph shows twice as many cycles in the same time. Faraday's law depends on how fast the flux changes, not on how large it is: $\varepsilon_0=NBA\omega$ (Section 14.3), so doubling $\omega$ doubles the peak emf as well as the frequency. Watch the coil too: the emf is largest when the plane of the coil is parallel to $\mathbf B$ โ€” when the flux through it is zero but changing fastest.
Teaser โ€” The AC Generator

A flat coil of $N=100$ turns, each of area $A=0.010\ \text{m}^2$, rotates at a steady rate between the poles of a magnet that produces a uniform field $B=0.50\ \text{T}$. Left: the coil seen along its axis of rotation, with its normal $\hat{\mathbf n}$. Right: the flux linkage $N\Phi_B$ (blue) and the induced emf (red) over the first $100\ \text{ms}$. Choose the rotation frequency and press Play (the rotation is shown slowed down $50$ times).

25 Hz
peak flux linkage $NBA$โ€”
peak emf $\varepsilon_0=NBA\omega$โ€”
rms emf ยท periodโ€”

Sections in this chapter

๐ŸŽฏ Chapter mixed test NEET ยท MCQ

Eight NEET-style questions that move between the three sections in no fixed order, as the paper does โ€” and several of them need ideas from two sections at once. Answer each one and press Submit (NEET marking: $+4$ correct, $-1$ wrong, $0$ unanswered), or press โฑ Take as a timed test. The test clock is generous: at real NEET pace โ€” about a minute per question โ€” you should finish all eight in ten minutes, so try to beat it comfortably. Try them before you open any solution.

E1. NEET ยท MCQ A coil of $100$ turns, each of area $0.020\ \text{m}^2$, rotates at $50$ revolutions per second about an axis perpendicular to a uniform magnetic field of $0.50\ \text{T}$. The peak emf induced in it is about (A) $50\ \text{V}$ (B) $314\ \text{V}$ (C) $222\ \text{V}$ (D) $157\ \text{V}$

ฯ‰ $\omega=2\pi\nu=100\pi\ \text{rad/s}$.
Peak emf $\varepsilon_0=NBA\omega=100\times0.50\times0.020\times100\pi=100\pi\approx314\ \text{V}$ (Section 14.3, from Faraday's law of Section 14.1).
Answer (B) $314\ \text{V}$.
โฑ Shortcut $NBA=1.0\ \text{Wb}$, so $\varepsilon_0$ is just $\omega$ in volts. (A) uses $\nu$ in place of $\omega$; (C) is the rms value, $\varepsilon_0/\sqrt2$; (D) is half the peak.

E2. NEET ยท MCQ Statement I: The self-inductance of a coil depends on the current flowing through it. Statement II: Lenz's law is a consequence of the law of conservation of energy. In the light of these statements, choose the correct option. (A) Both Statement I and Statement II are correct (B) Both Statement I and Statement II are incorrect (C) Statement I is correct but Statement II is incorrect (D) Statement I is incorrect but Statement II is correct

Statement I $L=N\Phi_B/I$, but $N\Phi_B$ is proportional to $I$, so $L$ depends only on the turns, the size and shape of the coil and its core (Section 14.2). Incorrect.
Statement II If the induced current aided the change of flux, a tiny push on a magnet would make it run away with ever more kinetic energy and heat โ€” energy from nothing (Section 14.1). Correct.
Answer (D).
โฑ Shortcut "$L$, $M$, $C$ and $R$ are properties of the device, never of the current or voltage" โ€” Statement I fails that test.

E3. NEET ยท MCQ A rod of length $0.50\ \text{m}$ is moved at a steady $4.0\ \text{m/s}$ along smooth horizontal rails joined by a $2.0\ \Omega$ resistor, in a uniform vertical field of $0.50\ \text{T}$. Other resistances are negligible. The force needed to keep the rod moving at this speed is (A) $0.125\ \text{N}$ (B) $0.25\ \text{N}$ (C) $0.50\ \text{N}$ (D) $1.0\ \text{N}$

Emf and current $\varepsilon=Blv=0.50\times0.50\times4.0=1.0\ \text{V}$ and $I=\dfrac{\varepsilon}{R}=0.50\ \text{A}$ (Section 14.1).
Force At steady speed the pull balances the magnetic force on the current: $F=BIl=0.50\times0.50\times0.50=0.125\ \text{N}$.
Answer (A) $0.125\ \text{N}$.
โฑ Shortcut Power check: $Fv=0.125\times4.0=0.50\ \text{W}=\dfrac{\varepsilon^2}{R}$ โœ“. (C) is the current in amperes and (D) the emf in volts โ€” numbers, but not forces; (B) uses $l$ once instead of twice in $B^2l^2v/R$.

E4. NEET ยท MCQ The graph shows the voltage $v$ across a single ideal circuit element (solid curve) and the current $i$ through it (dashed curve), both against time. The element is (A) a resistor (B) an inductor (C) a capacitor (D) a resistor and an inductor in series
tT/4T/23T/4Tvi

Read the phase The current reaches its peak at $t=0$, a quarter of a period before the voltage reaches its peak at $\tfrac T4$. So the current leads the voltage by exactly $\tfrac{\pi}{2}$.
Identify A resistor keeps $i$ in phase with $v$; an inductor makes $i$ lag by $\tfrac{\pi}{2}$; an RL combination makes it lag by less than $\tfrac{\pi}{2}$. Only a capacitor makes the current lead by $\tfrac{\pi}{2}$ (Section 14.3).
Answer (C) a capacitor.
โฑ Shortcut Whichever curve peaks first, leads. Current first โ‡’ "ICE" โ‡’ capacitor.

E5. NEET ยท MCQ Assertion (A): The emf of an AC generator is greatest at the instant the plane of its coil is perpendicular to the magnetic field. Reason (R): The magnetic flux through the coil is greatest when the plane of the coil is perpendicular to the field. Choose the correct option. (A) Both A and R are true and R is the correct explanation of A (B) Both A and R are true but R is not the correct explanation of A (C) A is true but R is false (D) A is false but R is true

Reason With the plane perpendicular to $\mathbf B$, the normal is along $\mathbf B$ and $\Phi_B=BA$, its greatest value (Section 14.1). True.
Assertion At that instant the flux is at a maximum, so it is momentarily not changing: the emf is zero. The emf is greatest when the plane is parallel to $\mathbf B$, where the flux is zero but changing fastest (Section 14.3). False.
Answer (D).
โฑ Shortcut Flux $\propto\cos\omega t$, emf $\propto\sin\omega t$: one is largest when the other is zero.

E6. NEET ยท MCQ Match each effect in List-I with an example of it in List-II.
List-I: (a) eddy currents (b) self-induction (c) mutual induction (d) motional emf
List-II: (i) a transformer (ii) an induction furnace (iii) a spark across a switch that breaks a circuit containing a large coil (iv) an emf between the ends of the axle of a moving railway carriage
Choose the correct answer: (A) a-i, b-iii, c-ii, d-iv (B) a-ii, b-i, c-iii, d-iv (C) a-ii, b-iii, c-i, d-iv (D) a-iv, b-iii, c-i, d-ii

Match (a) A furnace heats a metal charge with the eddy currents a rapidly alternating field induces in it โ€” ii (Section 14.2). (b) Breaking a circuit makes its own current fall fast, and the coil's back emf drives the spark โ€” iii. (c) A transformer's changing primary current induces the secondary emf โ€” i (Sections 14.2 and 14.3). (d) The axle is a conductor moving through the vertical component of the Earth's field โ€” iv (Section 14.1).
Answer (C) a-ii, b-iii, c-i, d-iv.
โฑ Shortcut "Transformer = two coils = mutual": c-i leaves only (C) and (D), and the axle is plainly a moving conductor, d-iv.

E7. NEET ยท MCQ A series circuit of $R=10\ \Omega$, $L=0.10\ \text{H}$ and $C=10\ \mu\text{F}$ is connected to a $50\ \text{V}$ (rms) source whose frequency is adjusted to resonance. The rms voltage across the inductor is (A) $50\ \text{V}$ (B) $500\ \text{V}$ (C) $250\ \text{V}$ (D) zero

Resonance $\omega_0=\dfrac{1}{\sqrt{LC}}=\dfrac{1}{\sqrt{0.10\times10^{-5}}}=1000\ \text{rad/s}$, and $Z=R$, so $I_\text{rms}=\dfrac{50}{10}=5.0\ \text{A}$ (Section 14.3).
Inductor $X_L=\omega_0L=100\ \Omega$, so $V_L=I_\text{rms}X_L=500\ \text{V}$ โ€” ten times the source voltage; $V_C$ is the same $500\ \text{V}$ in antiphase.
Answer (B) $500\ \text{V}$.
โฑ Shortcut $V_L=\dfrac{X_L}{R}V=\dfrac{100}{10}\times50$. (D) confuses "$V_L$ and $V_C$ cancel" with "each is zero"; (A) assumes no element can exceed the source voltage.

E8. NEET ยท MCQ How many of the following statements are correct?
(i) If the flux through a coil varies sinusoidally with time, the induced emf is zero at the instants when the flux is greatest.
(ii) An inductor $L$ carrying a current $I$ stores energy $\tfrac12LI^2$.
(iii) The mean value of a sinusoidal current over one complete cycle is $0.637$ times its peak value.
(iv) In a step-down transformer the current in the secondary is larger than the current in the primary.
(v) Eddy-current losses in a transformer are reduced by using a solid iron core.
(A) Three (B) Two (C) Four (D) Five

Check each (i) โœ“ โ€” the emf is the slope of the flux graph, which is zero at a peak (Sections 14.1 and 14.3). (ii) โœ“ (Section 14.2). (iii) โœ— โ€” over a full cycle the mean is zero; $0.637\,i_m=\tfrac{2}{\pi}i_m$ is the mean over a half cycle. (iv) โœ“ โ€” power is conserved, so a lower voltage comes with a larger current. (v) โœ— โ€” a laminated core reduces them; a solid core makes them worse.
Answer (A) three statements: (i), (ii) and (iv).
โฑ Shortcut Both false statements change one word of a true one: "complete" for "half", "solid" for "laminated". Read every word.
โœ… Before you start
You need the magnetic field of a long wire, a loop and a solenoid (Section 13.1), the force $I\mathbf L\times\mathbf B$ on a wire and the torque on a coil (Section 13.2); the flux idea copies electric flux (Section 11.2). Circuits use Ohm's law, electrical power and Kirchhoff's laws (Section 12.1, Section 12.2), and capacitors and the energy $\tfrac12CV^2$ (Section 11.4). Alternating quantities are sinusoidal functions with an amplitude, angular frequency and phase, exactly as in SHM (Section 10.1), and phasors are rotating vectors added by the rules of Section 2.2. From mathematics: differentiating $\sin\omega t$ and $\cos\omega t$, and the derivative as a rate of change.