5.3 Moment of Inertia
Mass tells you how hard a body is to accelerate; moment of inertia $I=\sum m_ir_i^2$ tells you how hard it is to spin. It depends on the axis as well as the mass, and two theorems — parallel axes and perpendicular axes — let you move from one axis to another without integrating again.
Try spinning a long broom about its middle, then about one end: the same broom, the same hands, but the second is far harder to start and to stop. A potter's wheel has a heavy stone rim so that it keeps turning between kicks; a gymnast tucks into a ball to turn a somersault quickly and stretches out to slow down; the flywheel in a car engine carries most of its mass at the outside edge. In each case what matters is not just how much mass there is, but how far from the axis it sits.
For straight-line motion the resistance to a change of velocity is the mass $m$. For rotation about an axis the corresponding resistance is the moment of inertia $I$. In this section we define it, find its value for the simple bodies NEET uses again and again (rods, rings, discs, cylinders, spheres, plates), and prove the two theorems that convert a known moment of inertia about one axis into the value about another. NEET expects the standard results to be recalled instantly: most questions are a table value, one theorem and a line of arithmetic, or a ratio of moments of inertia or radii of gyration. In Section 5.4 we put $I$ to work in $\tau=I\alpha$ and in the rotational kinetic energy $\tfrac12I\omega^2$. We use the ideas of a rigid body and its centre of mass from Section 5.1, and angular velocity from Section 2.4.
Moment of inertia and radius of gyration
Take a rigid body turning with angular velocity $\omega$ about a fixed axis. Every particle of the body moves in a circle about the axis. A particle of mass $m_i$ at perpendicular distance $r_i$ from the axis has speed $v_i=\omega r_i$ — the same $\omega$ for every particle, because the body is rigid — so its kinetic energy is $\tfrac12m_i\omega^2r_i^2$. Adding over all the particles,
$$K=\sum_i\tfrac12m_iv_i^2=\tfrac12\Big(\sum_im_ir_i^2\Big)\omega^2 .$$Compare this with $K=\tfrac12mv^2$ for a body moving in a straight line. The bracket plays exactly the part that the mass plays there: it is the "rotational mass" of the body for this axis. A particle near the axis contributes little, because it hardly moves; a particle far out contributes a lot, and its contribution grows as the square of the distance.
The moment of inertia of a system of particles about a given axis is
$$I=\sum_im_ir_i^2=m_1r_1^2+m_2r_2^2+\dots,$$where $r_i$ is the perpendicular distance of the particle $m_i$ from the axis. For a continuous body, divide it into mass elements $dm$ at perpendicular distance $r$ from the axis:
$$I=\int r^2\,dm .$$$I$ is a scalar, always positive; its SI unit is $\text{kg m}^2$ and its dimensions are $[\text{M}\text{L}^2]$.
Three things decide the moment of inertia: the mass of the body, how that mass is distributed, and the position and direction of the axis. A body has no single moment of inertia — it has one value for every axis, and you must always say which axis you mean. What $I$ does not depend on is how fast the body turns, or whether it turns at all: like mass, it is a property of the body (and the chosen axis), not of its motion.
It is often convenient to describe $I$ by a single length. Imagine squeezing the whole mass $M$ of the body into a thin ring (or a point) at a distance $k$ from the axis, chosen so that the moment of inertia is unchanged: $Mk^2=I$.
The radius of gyration $k$ of a body of mass $M$ about a given axis is the distance from the axis at which the whole mass could be concentrated without changing the moment of inertia:
$$I=Mk^2,\qquad k=\sqrt{\frac{I}{M}} .$$For $n$ equal particles, $k^2=\dfrac{r_1^2+r_2^2+\dots+r_n^2}{n}$: the radius of gyration is the root-mean-square distance of the mass from the axis. Like $I$, it depends on the axis; its unit is the metre.
A large $k$ means the mass lies, on average, far from the axis. Two bodies of the same mass can have very different moments of inertia: a ring and a disc of the same mass and radius have $k=R$ and $k=R/\sqrt2$ respectively, so the ring's $I$ is twice the disc's.
Why $r$ is a perpendicular distance. A particle moves in a circle whose radius is its perpendicular distance from the axis, not its distance from some chosen point on the axis. For a particle at $(x,y,z)$ the perpendicular distances from the three coordinate axes are $\sqrt{y^2+z^2}$, $\sqrt{z^2+x^2}$ and $\sqrt{x^2+y^2}$. Mixing these up is a common source of wrong answers, especially for spheres.
Every particle of a rigid body is moved to twice its present perpendicular distance from a fixed axis, keeping the mass the same. The moment of inertia about that axis
Moments of inertia of simple bodies
For a continuous body we cut it into elements whose distance from the axis is (nearly) the same throughout the element — thin strips for a rod, thin rings for a disc, thin shells for a sphere — and add their contributions with an integral. The method is always the same: write $dm$ in terms of the density and the size of the element, multiply by $r^2$, integrate.
Thin uniform rod, axis perpendicular to the rod through its centre. Let the rod have mass $M$ and length $L$, so its mass per unit length is $\lambda=M/L$. A small piece of length $dx$ at distance $x$ from the centre has $dm=\lambda\,dx$ and contributes $x^2\,dm$:
$$I_\text{cm}=\int_{-L/2}^{L/2}\frac{M}{L}x^2\,dx=\frac{M}{L}\cdot\frac{x^3}{3}\Big|_{-L/2}^{L/2}$$ $$=\frac{M}{L}\cdot\frac{2}{3}\cdot\frac{L^3}{8}=\frac{ML^2}{12}.$$About a perpendicular axis through one end, $x$ runs from $0$ to $L$: $I=\dfrac{M}{L}\cdot\dfrac{L^3}{3}=\dfrac{ML^2}{3}$, four times as much.
Thin ring (or thin-walled hollow cylinder), axis through the centre perpendicular to its plane. Every element is at the same distance $R$, so $I=\int R^2\,dm=R^2\int dm=MR^2$. The same holds for a thin cylindrical shell about its own axis, whatever its length: lengthening the tube along the axis does not move any mass farther from it.
Uniform disc (or solid cylinder), axis through the centre perpendicular to its face. With mass per unit area $\sigma=M/(\pi R^2)$, a thin ring of radius $r$ and width $dr$ has area $2\pi r\,dr$ and mass $dm=\sigma\,2\pi r\,dr$; all of it is at distance $r$:
$$I=\int_0^R r^2\,\sigma\,2\pi r\,dr=2\pi\sigma\frac{R^4}{4}$$ $$=\frac{M}{\pi R^2}\cdot\frac{\pi R^4}{2}=\frac{MR^2}{2}.$$A solid cylinder is a pile of such discs, so it too has $I=\tfrac12MR^2$ about its axis, for any length.
Thin spherical shell and solid sphere, axis along a diameter. For a sphere the perpendicular distance from a diameter is not the distance from the centre, so the integrals take a little more work; we quote the results. A thin spherical shell has $I=\tfrac23MR^2$. (One quick argument: by symmetry the shell has the same $I$ about the $x$-, $y$- and $z$-axes, and adding the three gives $\sum m(y^2+z^2+z^2+x^2+x^2+y^2)$ $=2\sum mR^2=2MR^2$, so each is $\tfrac23MR^2$.) Building a solid sphere from thin shells of radius $r$ and mass $dm=\tfrac{3M}{R^3}r^2\,dr$, each contributing $\tfrac23r^2\,dm$, gives
$$I=\int_0^R\frac23r^2\cdot\frac{3M}{R^3}r^2\,dr$$ $$=\frac{2M}{R^3}\cdot\frac{R^5}{5}=\frac25MR^2 .$$| Body | Axis | $I$ | $k$ |
|---|---|---|---|
| thin rod, length $L$ | ⟂ to the rod, through its centre | $\tfrac{1}{12}ML^2$ | $\tfrac{L}{2\sqrt3}$ |
| thin rod, length $L$ | ⟂ to the rod, through one end | $\tfrac13ML^2$ | $\tfrac{L}{\sqrt3}$ |
| thin ring or thin-walled hollow cylinder, radius $R$ | central axis (⟂ to the plane of the ring) | $MR^2$ | $R$ |
| thin ring, radius $R$ | a diameter | $\tfrac12MR^2$ | $\tfrac{R}{\sqrt2}$ |
| disc or solid cylinder, radius $R$ | central axis | $\tfrac12MR^2$ | $\tfrac{R}{\sqrt2}$ |
| disc, radius $R$ | a diameter | $\tfrac14MR^2$ | $\tfrac R2$ |
| annular disc, radii $R_1$, $R_2$ | central axis | $\tfrac12M(R_1^2+R_2^2)$ | $\sqrt{\tfrac{R_1^2+R_2^2}{2}}$ |
| thin spherical shell, radius $R$ | a diameter | $\tfrac23MR^2$ | $\sqrt{\tfrac23}\,R$ |
| solid sphere, radius $R$ | a diameter | $\tfrac25MR^2$ | $\sqrt{\tfrac25}\,R$ |
| rectangular plate, sides $a$, $b$ | through the centre, in the plane, parallel to side $b$ | $\tfrac{1}{12}Ma^2$ | $\tfrac{a}{2\sqrt3}$ |
| rectangular plate, sides $a$, $b$ | through the centre, ⟂ to the plate | $\tfrac{1}{12}M(a^2+b^2)$ | $\sqrt{\tfrac{a^2+b^2}{12}}$ |
All bodies are uniform (constant density). The diameter results and the perpendicular-plate result follow from the theorems below.
Read the table as a story about distribution. For axes through the centre the coefficient of $MR^2$ falls from $1$ (ring: all mass at $R$) to $\tfrac23$ (shell: some mass near the axis) to $\tfrac12$ (disc: much mass near the centre) to $\tfrac25$ (solid sphere: mass concentrated near the axis in three dimensions). For the rectangular plate about an axis parallel to side $b$, only the dimension $a$ across the axis matters; the plate is just a row of rods of length $a$.
Choose the disc with $M=2.0\ \text{kg}$ and $R=0.50\ \text{m}$ in the widget. What share of its moment of inertia comes from the outer half of the disc (the part with $r\gt R/2$)?
A thin ring and a uniform disc have the same mass $M$ and the same radius $R$. About their central axes, $I_\text{ring}/I_\text{disc}$ is
The parallel axes theorem
The table gives $I$ about axes through the centre of mass. Problems often need an axis somewhere else — a rod swinging about one end, a disc turning about a nail through its rim, a door on its hinges. There is no need to integrate again.
Let $I_\text{cm}$ be the moment of inertia of a body of mass $M$ about an axis through its centre of mass. Then about any parallel axis at perpendicular distance $d$ from it,
$$I=I_\text{cm}+Md^2 .$$It holds for every body (flat or three-dimensional, uniform or not). The two axes must be parallel, and one of them must pass through the centre of mass.
Proof. Take the $z$-axis along the axis through the centre of mass, with the centre of mass at the origin, and let the new axis be parallel to it, passing through $(d,0)$ in the $xy$-plane. A particle at $(x_i,y_i,z_i)$ has squared distance $x_i^2+y_i^2$ from the first axis and $(x_i-d)^2+y_i^2$ from the second. So
$$I=\sum m_i\big[(x_i-d)^2+y_i^2\big]$$ $$=\sum m_i(x_i^2+y_i^2)-2d\sum m_ix_i+d^2\sum m_i .$$The first sum is $I_\text{cm}$ and the last is $Md^2$. The middle sum is $Mx_\text{cm}=0$, because the centre of mass is at the origin. That cancellation is exactly why one axis must pass through the centre of mass: for two arbitrary parallel axes the cross term does not vanish.
Two consequences are worth remembering. First, since $Md^2\ge0$, the moment of inertia is smallest about the axis through the centre of mass, among all axes in a given direction. Second, to go from one off-centre axis $A$ to another parallel axis $B$, go through the centre: $I_B=I_A-Md_A^2+Md_B^2$, never $I_A+M(\text{distance }AB)^2$.
In the widget choose the rod ($3.0\ \text{kg}$, $1.0\ \text{m}$) and slide the axis from the centre to one end ($d=0.50\ \text{m}$). By what factor does $I$ grow?
A body of mass $M$ has moment of inertia $I_A$ about an axis $A$ at distance $d$ from its centre of mass. Axis $B$ is parallel to $A$, at distance $2d$ from the centre of mass on the other side (so $A$ and $B$ are $3d$ apart). Then $I_B$ equals
The perpendicular axes theorem
For a flat body — a plate, a ring, a disc, a wire frame lying in a plane — there is a second short cut, which links the moment of inertia about an axis perpendicular to the plane with the moments about two axes lying in the plane.
A plane lamina is a body whose mass lies entirely in one plane, with negligible thickness: a thin plate, disc, ring or flat frame of wire.
For a plane lamina in the $xy$-plane, the moment of inertia about an axis $z$ perpendicular to the plane equals the sum of the moments of inertia about two perpendicular axes $x$ and $y$ lying in the plane and meeting the $z$-axis at the same point:
$$I_z=I_x+I_y .$$The point need not be the centre of mass. The theorem does not apply to three-dimensional bodies such as spheres, cubes or thick cylinders.
Proof. Every particle of the lamina has $z_i=0$. Its perpendicular distance from the $z$-axis satisfies $r_i^2=x_i^2+y_i^2$, while its distance from the $x$-axis is $|y_i|$ and from the $y$-axis is $|x_i|$. Hence $I_z=\sum m_i(x_i^2+y_i^2)$ $=\sum m_iy_i^2+\sum m_ix_i^2$ $=I_x+I_y$. For a solid body the distance from the $x$-axis would be $\sqrt{y_i^2+z_i^2}$, the $z_i^2$ terms would not cancel, and the result fails.
Diameters of a ring and a disc. By symmetry a ring has the same $I_d$ about every diameter. Two perpendicular diameters and the central axis meet at the centre, so $I_d+I_d=MR^2$ and $I_d=\tfrac12MR^2$. For a disc, $2I_d=\tfrac12MR^2$ gives $I_d=\tfrac14MR^2$. For a square plate of side $a$ the axes through the centre parallel to the sides each have $\tfrac1{12}Ma^2$, so $I_z=\tfrac16Ma^2$; and since the two diagonals are also perpendicular axes through the centre with equal moments (by symmetry), each diagonal also has $\tfrac1{12}Ma^2$. In fact a square lamina has the same moment of inertia about every axis through its centre in its plane.
Combining the two theorems gives every "tangent" result NEET asks for. For a disc: tangent in its plane $=\tfrac14MR^2+MR^2=\tfrac54MR^2$; tangent perpendicular to its plane (axis through a rim point) $=\tfrac12MR^2+MR^2=\tfrac32MR^2$. For a ring: $\tfrac32MR^2$ and $2MR^2$.
- Split the body into standard pieces (rods, rings, discs, spheres, plates). For a body with a hole, treat it as the full body minus the removed piece, with masses in proportion to area or volume.
- For each piece, start from its table value about an axis through its own centre of mass, parallel to the required axis. If the piece is flat and you need an in-plane axis, use the perpendicular axes theorem first.
- Shift each piece to the required axis with $I=I_\text{cm}+Md^2$, where $d$ is the distance from that piece's centre of mass.
- Add (or subtract) the moments — all about the same axis. Check the answer is positive and has units of $\text{kg m}^2$.
(b) The radius of gyration of a thin uniform rod of length $L$ about an axis perpendicular to it through a point $L/4$ from one end is (A) $\dfrac L4$ (B) $L\sqrt{\dfrac{7}{48}}$ (C) $\dfrac{L}{2\sqrt3}$ (D) $L\sqrt{\dfrac{7}{12}}$.
1. Measuring $d$ from the wrong place. In $I=I_\text{cm}+Md^2$, $d$ is the distance between the new axis and the parallel axis through the centre of mass. A rod turning about a point $L/3$ from one end has $d=L/2-L/3=L/6$, giving $\tfrac{1}{12}ML^2+\tfrac{1}{36}ML^2=\tfrac19ML^2$; using $d=L/3$ (the distance from the end) gives the wrong $\tfrac{7}{36}ML^2$. Never shift directly between two off-centre axes.
2. The perpendicular axes theorem on a solid body. It holds only for a plane lamina, with the two in-plane axes and the perpendicular axis all meeting at one point. For a solid sphere $I_x+I_y=\tfrac45MR^2\ne I_z$.
3. What $I$ depends on. Mass, its distribution, and the position and direction of the axis — not the angular velocity or the torque applied. Statement questions also try "a body has a fixed moment of inertia": it has one value for every axis.
4. Square roots. $k=\sqrt{I/M}$, so a ratio of radii of gyration is the square root of the ratio of the moments of inertia. A ring and a disc of the same mass and radius: $I$ in the ratio $2:1$, $k$ in the ratio $\sqrt2:1$ — the options will contain both.
5. Taking $r$ as the distance from the centre. $r$ in $\sum mr^2$ is the perpendicular distance from the axis. That is why a spherical shell has $\tfrac23MR^2$, not $MR^2$, about a diameter.
6. The wrong shape, or a hole. Hollow cylinder = ring ($MR^2$); solid cylinder = disc ($\tfrac12MR^2$), whatever the length. Annular disc: $\tfrac12M(R_1^2+R_2^2)$ — a plus sign. For a hole, subtract the removed piece's $I$ about the same axis, and divide by the remaining mass to find $k$.
The moment of inertia of a uniform disc of mass $M$ and radius $R$ about a diameter is
Exercises
All bodies are uniform unless stated otherwise. "Rod" means a thin rod; "light" means of negligible mass.
- 1 Find the moment of inertia of a $0.50\ \text{kg}$ particle at a perpendicular distance of $0.40\ \text{m}$ from an axis.
- 2 Two $2.0\ \text{kg}$ balls are fixed at the ends of a light rod $0.60\ \text{m}$ long. Find $I$ about an axis perpendicular to the rod through (a) its midpoint, (b) one of the balls.
- 3 Four $1.0\ \text{kg}$ particles sit at the corners of a square of side $0.20\ \text{m}$, joined by light rods. Find $I$ about (a) the axis through the centre perpendicular to the square, (b) one side, (c) a diagonal.
- 4 A $5.0\ \text{kg}$ wheel has $I=0.20\ \text{kg m}^2$ about its axle. Find its radius of gyration.
- 5 Express the radius of gyration of a uniform disc about its central axis in terms of its radius $R$, and evaluate it for $R=0.30\ \text{m}$.
- 6 State the SI unit and the dimensions of moment of inertia and of radius of gyration. Does either depend on the angular velocity of the body?
- 7 Particles of mass $1.0$, $2.0$ and $3.0\ \text{kg}$ are at $(0,0)$, $(0.30\ \text{m},0)$ and $(0,0.40\ \text{m})$ in the $xy$-plane. Find $I$ about (a) the $z$-axis, (b) the $x$-axis, (c) the $y$-axis. Check that (a) = (b) + (c).
- 8 Show that a two-particle system ($m_1$, $m_2$ a distance $d$ apart) has $I=\mu d^2$ about a perpendicular axis through its centre of mass, where $\mu=\dfrac{m_1m_2}{m_1+m_2}$. Evaluate $I$ for a carbon monoxide molecule ($m_\text{C}=12\ \text{u}$, $m_\text{O}=16\ \text{u}$, $1\ \text{u}=1.66\times10^{-27}\ \text{kg}$, $d=1.13\times10^{-10}\ \text{m}$).
- 1 Find $I$ of a thin ring of mass $0.80\ \text{kg}$ and radius $0.25\ \text{m}$ about its central axis.
- 2 Find $I$ of a disc of mass $2.0\ \text{kg}$ and diameter $0.40\ \text{m}$ about its central axis.
- 3 Find $I$ of a solid sphere of mass $3.0\ \text{kg}$ and radius $0.10\ \text{m}$ about a diameter.
- 4 Find $I$ of a thin spherical shell of the same mass and radius as in part 3, about a diameter.
- 5 A rod of mass $0.80\ \text{kg}$ and length $1.5\ \text{m}$. Find $I$ about a perpendicular axis through (a) its centre, (b) one end.
- 6 A rectangular plate of mass $1.2\ \text{kg}$ measures $0.60\ \text{m}\times0.40\ \text{m}$. Find $I$ about (a) the axis through its centre in its plane parallel to the $0.40\ \text{m}$ sides, (b) the axis through its centre perpendicular to the plate.
- 7 A solid cylinder of mass $4.0\ \text{kg}$, radius $0.15\ \text{m}$ and length $0.50\ \text{m}$ turns about its own axis. Find $I$. Would a cylinder twice as long, of the same mass and radius, have a different $I$ about this axis?
- 8 Two uniform discs have the same mass and the same thickness, but the density of the first is twice that of the second. Find the ratio $I_1/I_2$ of their moments of inertia about their central axes.
- 9 Derive $I=\tfrac13ML^2$ for a rod about a perpendicular axis through one end directly from $I=\int r^2\,dm$.
- 1 Find $I$ of a disc of mass $2.0\ \text{kg}$ and radius $0.20\ \text{m}$ about an axis perpendicular to it through a point on its rim.
- 2 A rod of mass $0.50\ \text{kg}$ and length $1.2\ \text{m}$ turns about a perpendicular axis $0.30\ \text{m}$ from one end. Find $I$.
- 3 Find $I$ of a solid sphere of mass $2.0\ \text{kg}$ and radius $0.15\ \text{m}$ about a tangent.
- 4 A $4.0\ \text{kg}$ body has $I=0.90\ \text{kg m}^2$ about an axis $A$ that is $0.30\ \text{m}$ from its centre of mass. Find $I$ about (a) the parallel axis through the centre of mass, (b) a parallel axis $0.50\ \text{m}$ from the centre of mass.
- 5 At what distance from the centre of a disc of radius $0.25\ \text{m}$ must a perpendicular axis be placed so that $I$ about it is twice $I_\text{cm}$?
- 6 A pendulum consists of a rod (mass $0.40\ \text{kg}$, length $1.0\ \text{m}$) pivoted at its top end, with a solid sphere (mass $1.0\ \text{kg}$, radius $0.10\ \text{m}$) fixed with its centre at the rod's lower end. Find $I$ about the pivot. By how much would treating the sphere as a point mass change the answer?
- 7 Two rods, each of mass $0.50\ \text{kg}$ and length $0.60\ \text{m}$, are joined at their ends to form an L. Find $I$ about the axis through the joint perpendicular to the plane of the L.
- 8 Use the parallel axes theorem to explain why, among all axes in a given direction, the moment of inertia is least for the one through the centre of mass.
- 1 Find $I$ of a disc of mass $1.0\ \text{kg}$ and radius $0.30\ \text{m}$ about a diameter.
- 2 Find $I$ of the same disc about a tangent lying in its plane.
- 3 Find $I$ of a ring of mass $0.60\ \text{kg}$ and radius $0.10\ \text{m}$ about a tangent in its plane.
- 4 A square plate of side $0.50\ \text{m}$ has mass $2.0\ \text{kg}$. Find $I$ about (a) a diagonal, (b) the axis through its centre perpendicular to it, (c) the axis through one corner perpendicular to it.
- 5 For a ring, find the ratio of $I$ about a tangent perpendicular to its plane to $I$ about a tangent in its plane.
- 6 A disc of radius $0.30\ \text{m}$ has mass $9.0\ \text{kg}$. A circular piece of radius $0.10\ \text{m}$, centred $0.15\ \text{m}$ from the disc's centre, is cut out. Find $I$ of the remaining body about the axis through the original centre perpendicular to its plane.
- 7 A wire of mass $0.40\ \text{kg}$ and length $1.2\ \text{m}$. Find $I$ (a) when straight, about a perpendicular axis through its centre, (b) when bent into a circular ring, about the axis through the ring's centre perpendicular to its plane. Find the ratio (a)/(b).
E1. NEET · MCQ The moment of inertia of a uniform disc of mass $2.0\ \text{kg}$ and radius $0.20\ \text{m}$ about a tangent lying in its plane is (A) $0.020\ \text{kg m}^2$ (B) $0.10\ \text{kg m}^2$ (C) $0.12\ \text{kg m}^2$ (D) $0.040\ \text{kg m}^2$
E2. NEET · MCQ Match List-I (uniform bodies of mass $M$ and radius $R$) with List-II (moment of inertia).
List-I: (a) thin ring about a diameter (b) disc about a tangent perpendicular to its plane (c) solid sphere about a tangent (d) thin spherical shell about a diameter
List-II: (i) $\tfrac23MR^2$ (ii) $\tfrac75MR^2$ (iii) $\tfrac12MR^2$ (iv) $\tfrac32MR^2$
Choose the correct answer: (A) a-iii, b-ii, c-iv, d-i (B) a-i, b-iv, c-ii, d-iii (C) a-iii, b-iv, c-ii, d-i (D) a-iv, b-iii, c-ii, d-i
E3. NEET · MCQ Statement I: The parallel axes theorem $I=I_\text{cm}+Md^2$ may be applied between any two parallel axes of a body, with $d$ the distance between them. Statement II: Of all the axes in a given direction, the moment of inertia of a body is least about the one through its centre of mass. In the light of these statements, choose the correct option. (A) Both Statement I and Statement II are correct (B) Both Statement I and Statement II are incorrect (C) Statement I is correct but Statement II is incorrect (D) Statement I is incorrect but Statement II is correct
E4. NEET · MCQ Assertion (A): A solid cylinder and a thin-walled hollow cylinder of the same mass and radius have the same moment of inertia about their axes. Reason (R): The moment of inertia of a cylinder about its own axis does not depend on its length. Choose the correct option. (A) Both A and R are true and R is the correct explanation of A (B) Both A and R are true but R is not the correct explanation of A (C) A is true but R is false (D) A is false but R is true
E5. NEET · MCQ The figure shows a uniform square plate $ABCD$ of mass $M$ and side $a$, and four axes: $1$ through the centre parallel to $AB$, $2$ along the diagonal $AC$, $3$ along the side $AB$ (all three in the plane of the plate), and $4$ through the centre perpendicular to the plate. Their moments of inertia satisfy (A) $I_1\lt I_2\lt I_4\lt I_3$ (B) $I_1=I_2\lt I_4\lt I_3$ (C) $I_1=I_2=I_4\lt I_3$ (D) $I_2\lt I_1\lt I_3\lt I_4$
E6. NEET · MCQ How many of the following statements are correct?
(i) The radius of gyration of a uniform disc of radius $R$ about its central axis is $R/\sqrt2$.
(ii) The moment of inertia of a body about a fixed axis increases when the body spins faster.
(iii) The perpendicular axes theorem can be used to find the moment of inertia of a solid sphere about a diameter.
(iv) The moment of inertia of a thin uniform rod about a perpendicular axis through one end is $\tfrac13ML^2$.
(v) A thin spherical shell has a larger moment of inertia about a diameter than a solid sphere of the same mass and radius.
(A) Three (B) Two (C) Four (D) Five
Research question. How well can a real rotating object — a bicycle wheel, a ceiling-fan rotor or a cricket bat swung about the handle — be modelled as a combination of the standard bodies in Result 5.10?
Why it matters. Engineers rarely integrate $\int r^2\,dm$ for a real part. They split it into rods, rings, discs and plates, add the pieces with the parallel axes theorem, and check against a measurement or a computer model. Bicycle designers fight to cut rim mass because rim mass dominates the wheel's $I$; bat makers and racket makers quote a "swing weight", which is a moment of inertia about the handle; turbine and flywheel designers trade mass against radius. Knowing which parts of an object carry most of its $I$ tells you where design changes will pay off.
What to do.
- Choose an object you can weigh in parts or estimate part by part: a bicycle wheel (rim, tyre, spokes, hub) is ideal. Measure every dimension with a metre scale or tape and estimate each part's mass (kitchen scale, manufacturer's data or density × volume).
- Model each part: rim + tyre as a ring, each spoke as a rod about one end (its inner end near the axle), the hub as a small solid cylinder. Write down $I$ of each part about the axle.
- Add the parts. Make a table of each part's percentage share of the total. How much comes from the rim and tyre alone? Compare with the widget's "outer-half share".
- Find the radius of gyration $k$ and compare it with the rim radius.
- Optional measurement: wrap a string round the axle, hang a known small mass and time its fall from rest; the method of Section 5.4 then gives a measured $I$ to compare with your model.
Tools: Metre scale or tape, kitchen scale, a spreadsheet; optionally string, a $100$–$200\ \text{g}$ mass and a phone stopwatch.
Hand in: A labelled sketch of the model, the table of parts with their $I$ and percentage shares, the total $I$ and $k$, and one paragraph on which simplification you trust least and why.
Going further. A racing team wants to cut the wheel's $I$ by $10\%$. Is it cheaper (in grams removed) to lighten the rim or the hub? Use your table to argue for an answer.
🧪 Self-check quiz
Q1. The moment of inertia of a rigid body about an axis does not depend on
Q2. The radius of gyration of a thin uniform rod of length $L$ about a perpendicular axis through one end is
Q3. A uniform disc has moment of inertia $I$ about its central axis (perpendicular to its plane). Its moment of inertia about a tangent lying in its plane is
Q4. The moment of inertia of a uniform solid sphere of mass $M$ and radius $R$ about a tangent is
Q5. The perpendicular axes theorem $I_z=I_x+I_y$ can be applied to