Chapter 19 ยท Introduction

Chapter 19 โ€” Electronic Devices

A few impurity atoms per million turn silicon into n-type or p-type material; join the two and you get a pโ€“n junction that lets current pass one way only. That one-way valve becomes rectifiers, LEDs, photodiodes, solar cells and voltage regulators โ€” and switching circuits that compute with 0s and 1s through logic gates.

A phone charger, an LED bulb, the solar panel on a roof and the processor inside a laptop look nothing alike, yet they are all built from the same material: silicon, purified to one foreign atom in a billion and then deliberately "spoiled" with a few atoms of phosphorus or boron per million. That tiny amount of impurity raises the conductivity of silicon tens of thousands of times and decides whether the current is carried by electrons or by holes. Put a p-type layer against an n-type layer and you have the most important device of the twentieth century โ€” the pโ€“n junction diode, a one-way valve for electric current. India's solar parks, the $230\ \text{V}$-to-$5\ \text{V}$ adapter on every desk and the white LEDs that replaced filament bulbs all rest on how such a junction behaves.

This chapter builds the story in three steps. First, semiconductors: energy bands and the band gap separate conductors, insulators and semiconductors; electrons and holes carry current; doping makes n-type and p-type material obeying the mass-action law $n_en_h=n_i^2$; and a pโ€“n junction forms a depletion layer and a barrier potential that make its Iโ€“V characteristic one-sided. Second, diode circuits: with the ideal or $0.7\ \text{V}$ model you can solve any circuit with diodes, build half-wave and full-wave rectifiers, and use the special diodes โ€” the LED, the photodiode, the solar cell and the Zener diode as a voltage regulator. Third, logic gates: OR, AND, NOT, NAND and NOR, their truth tables and waveforms, De Morgan's theorems, and why NAND or NOR alone can build every other gate.

NEET usually asks a couple of questions from this chapter, and they are among the quickest marks in the physics section: short MCQs on the dopant that makes a given type, the minority-carrier concentration, the junction under forward and reverse bias, the output of a rectifier, the bias and characteristic of each special diode, the currents of a Zener regulator, and the gate hidden in a truth table, a waveform or a small circuit. The NEET (UG) syllabus for this unit โ€” semiconductors; the semiconductor diode and its Iโ€“V characteristics in forward and reverse bias; the diode as a rectifier; the Iโ€“V characteristics of the LED, the photodiode, the solar cell and the Zener diode; the Zener diode as a voltage regulator; and the logic gates OR, AND, NOT, NAND and NOR โ€” is covered completely by the three sections below.

Energy bands, $E_g$โ†’Electrons & holesโ†’Doping: $n_en_h=n_i^2$โ†’pโ€“n junction, barrierโ†’Forward & reverse biasโ†’Rectifierโ†’LED, photodiode, solar cellโ†’Zener regulatorโ†’OR, AND, NOTโ†’NAND, NOR: universal
๐ŸŽฏ By the end of this chapter you canโ€ฆ
  • classify solids as conductors, insulators and semiconductors from their energy bands, and use the band gap with $hc=1240\ \text{eV nm}$;
  • explain intrinsic and extrinsic (n-type and p-type) semiconductors, use the mass-action law $n_en_h=n_i^2$, and find conductivity from $\sigma=e(n_e\mu_e+n_h\mu_h)$;
  • explain the depletion layer and barrier potential of a pโ€“n junction, and how forward and reverse bias change them;
  • draw and read the Iโ€“V characteristic of a diode, and find its static and dynamic resistance;
  • solve circuits with ideal diodes and with the $0.7\ \text{V}$ model, and find the output peak, frequency and average value of half-wave and full-wave rectifiers;
  • explain the working and Iโ€“V characteristics of the LED, the photodiode and the solar cell, and which bias each one uses;
  • analyse a Zener voltage regulator: decide whether it regulates, and find the series, load and Zener currents;
  • write the truth tables and Boolean expressions of OR, AND, NOT, NAND and NOR gates, draw output waveforms, use De Morgan's theorems and identify the single gate equivalent to a combination;
  • solve NEET multiple-choice questions that mix all three sections in every format the paper uses โ€” single answer, statement I / II, assertionโ€“reason, matching lists, "how many are correct" and graph or diagram reading โ€” quickly, by eliminating options.

Two silicon diodes (each $0.7\ \text{V}$ when conducting) have their anodes connected to inputs A and B and their cathodes joined to an output that is connected to earth through a $1\ \text{k}\Omega$ resistor. Input A is at $5\ \text{V}$ and input B at $0\ \text{V}$. What is the output?

Choose the OR circuit and set $A=5\ \text{V}$, $B=0\ \text{V}$. The readouts show D1 forward, D2 reverse, $V_\text{out}=4.3\ \text{V}$ and a current of $4.3\ \text{mA}$ in the resistor, so the output is logic $1$. Diode A conducts and holds the output $0.7\ \text{V}$ below its input (the $0.7\ \text{V}$ model of Section 19.2); diode B then has $0\ \text{V}$ on its anode and $4.3\ \text{V}$ on its cathode โ€” reverse biased, an open switch (Section 19.1). Try all four input pairs: the output is high if A or B is high โ€” an OR gate (Section 19.3). Then switch to the AND circuit, where the diodes are reversed and the resistor goes to $+5\ \text{V}$: now the output is high only when both inputs are high.
Teaser โ€” Logic Gates Made of Diodes

Two silicon diodes and one $1\ \text{k}\Omega$ resistor make a logic gate. Each input is either $0\ \text{V}$ (logic $0$) or $5\ \text{V}$ (logic $1$); an output above $2.5\ \text{V}$ counts as logic $1$. Choose the circuit, click the input buttons, and see which diode is forward biased (green, carrying current) and which is reverse biased (grey). Press Play to see the current flow.

diode D1 (from A)โ€”
diode D2 (from B)โ€”
output voltage, current in Rโ€”
logic output Yโ€”

Sections in this chapter

๐ŸŽฏ Chapter mixed test NEET ยท MCQ

Eight NEET-style questions drawn from all three sections and shuffled, as the paper does โ€” and several of them need an idea from one section and a circuit from another. Answer each one and press Submit (NEET marking: $+4$ correct, $-1$ wrong, $0$ unanswered), or press โฑ Take as a timed test. The test clock is generous: at real NEET pace โ€” about a minute per question โ€” you should finish all eight in ten minutes, so try to beat it comfortably. Take $hc=1240\ \text{eV nm}$, and try every question before you open any solution.

E1. NEET ยท MCQ An LED is to emit red light of wavelength $620\ \text{nm}$. The band gap of its semiconductor, and the way the LED must be biased, are (A) $2.0\ \text{eV}$; reverse bias (B) $2.0\ \text{eV}$; forward bias (C) $0.50\ \text{eV}$; forward bias (D) $2.0\ \text{eV}$; no bias is needed

Band gap Each photon carries about $E_g$ (Sections 19.1 and 19.2): $E_g\approx\dfrac{1240}{620}=2.0\ \text{eV}$.
Bias Light comes from electrons and holes recombining after being injected across the junction, which needs forward bias (Section 19.2).
Answer (B).
โฑ Shortcut (C) divides the wrong way round ($620/1240$); (A) and (D) describe the photodiode and the solar cell. LED = forward, always.

E2. NEET ยท MCQ Statement I: When a pโ€“n junction is forward biased, its potential barrier is lowered and its depletion layer becomes narrower. Statement II: A Zener diode is made from lightly doped p and n regions, which gives it a wide depletion layer and a low breakdown voltage. In the light of these statements, choose the correct option. (A) Both Statement I and Statement II are correct (B) Both Statement I and Statement II are incorrect (C) Statement I is correct but Statement II is incorrect (D) Statement I is incorrect but Statement II is correct

Statement I The applied voltage opposes the barrier, which falls to $V_0-V$, and majority carriers are pushed towards the junction (Section 19.1). Correct.
Statement II A Zener diode is heavily doped: its depletion layer is very thin, so a few volts already give a field strong enough for breakdown (Section 19.2). Incorrect.
Answer (C).
โฑ Shortcut Statement II contradicts itself: a wide depletion layer means a weak field, which would need a high voltage to break down.

E3. NEET ยท MCQ Assertion (A): The reverse current of a silicon diode (below breakdown) increases when the diode is heated. Reason (R): Heating breaks more covalent bonds in the crystal, increasing the number of minority carriers. Choose the correct option. (A) Both A and R are true and R is the correct explanation of A (B) Both A and R are true but R is not the correct explanation of A (C) A is true but R is false (D) A is false but R is true

Assertion True โ€” the reverse saturation current roughly doubles for every $10^\circ\text{C}$ rise (Section 19.1).
Reason True, and it is the explanation: the reverse current is the drift of minority carriers, whose number is set by thermal generation of electronโ€“hole pairs, not by the reverse voltage.
Answer (A).
โฑ Shortcut Reverse current = minority carriers = thermally made. Anything that makes more pairs (heat or light) raises it.

E4. NEET ยท MCQ Match List-I with List-II.
List-I: (a) the majority carriers in an n-type semiconductor (b) the bias at which a photodiode is used (c) the gate whose output is 1 only when all its inputs are 0 (d) the sign of the fixed ions on the p side of a depletion layer
List-II: (i) NOR (ii) negative (iii) electrons (iv) reverse
Choose the correct answer: (A) a-iii, b-ii, c-i, d-iv (B) a-ii, b-iv, c-i, d-iii (C) a-iii, b-iv, c-ii, d-i (D) a-iii, b-iv, c-i, d-ii

Match (a) n-type: electrons, iii (Section 19.1). (b) photodiode: reverse bias, iv (Section 19.2). (c) NOR, i (Section 19.3). (d) the p side loses holes and uncovers negative acceptor ions: negative, ii (Section 19.1).
Answer (D) a-iii, b-iv, c-i, d-ii.
โฑ Shortcut Only one item in List-II is a gate, so c-i โ€” that removes (C). Only (iv) is a bias, so b-iv โ€” that removes (A). (B) gives the carriers a "negative" label instead of naming them.

E5. NEET ยท MCQ The graph shows how the load voltage $V_L$ of a Zener regulator varies with its input voltage $V_{in}$. The series resistance is $200\ \Omega$ and the load is $600\ \Omega$. When $V_{in}=12\ \text{V}$, the current through the Zener diode is (A) $30\ \text{mA}$ (B) $10\ \text{mA}$ (C) $20\ \text{mA}$ (D) $60\ \text{mA}$
246810121424680Vin (V)VL (V)

Read The flat part of the graph gives $V_Z=6\ \text{V}$; at $V_{in}=12\ \text{V}$ the regulator is on the flat part, so $V_L=6\ \text{V}$. (Below $8\ \text{V}$ the line is the divider $V_{in}\times\tfrac{600}{800}$ and the Zener is off.)
Currents $I_s=\dfrac{12-6}{200}=30\ \text{mA}$, $\ I_L=\dfrac{6}{600}=10\ \text{mA}$, $\ I_Z=30-10=20\ \text{mA}$ (Section 19.2).
Answer (C).
โฑ Shortcut (A) is the series current, (B) the load current, (D) forgets to subtract $V_Z$ ($12/200$). The kink at $(8\ \text{V},\ 6\ \text{V})$ checks the data: $8\times\tfrac{600}{800}=6$ โœ“.

E6. NEET ยท MCQ How many of the following statements are correct?
(i) A bridge rectifier of silicon diodes gives an output peak about $1.4\ \text{V}$ below the input peak.
(ii) $\overline{A+B}=\overline{A}\cdot\overline{B}$.
(iii) An n-type semiconductor carries a net negative charge.
(iv) A NOR gate is a universal gate.
(v) The ripple of a half-wave rectifier working on the $50\ \text{Hz}$ mains has a frequency of $100\ \text{Hz}$.
(A) Two (B) Three (C) Four (D) Five

Check each (i) โœ“ โ€” two diodes conduct in series in each half-cycle (Section 19.2). (ii) โœ“ โ€” De Morgan (Section 19.3). (iii) โœ— โ€” doped crystals are neutral (Section 19.1). (iv) โœ“ (Section 19.3). (v) โœ— โ€” a half-wave output repeats at $f=50\ \text{Hz}$; $100\ \text{Hz}$ is the full-wave value.
Answer (B) three statements: (i), (ii) and (iv).
โฑ Shortcut Statements (iii) and (v) are two of the chapter's most-tested slips โ€” learn to spot them on sight.

E7. NEET ยท MCQ A germanium diode and a silicon diode are connected in parallel, both pointing the same way, and the pair is connected in series with a $100\ \Omega$ resistor across a $6.0\ \text{V}$ battery so that both diodes are forward biased. Using the usual constant-voltage-drop model for each material, the current drawn from the battery is (A) $53\ \text{mA}$ (B) $50\ \text{mA}$ (C) $60\ \text{mA}$ (D) $57\ \text{mA}$

Which diode? The germanium diode starts conducting at $0.3\ \text{V}$ (Section 19.1) and then holds the voltage across the parallel pair at $0.3\ \text{V}$ โ€” too little for the silicon diode, which needs $0.7\ \text{V}$. Only the germanium diode conducts (Section 19.2).
Current $I=\dfrac{6.0-0.3}{100}=0.057\ \text{A}=57\ \text{mA}$.
Answer (D).
โฑ Shortcut Parallel diodes: the lowest knee wins and the drops do not add. (A) uses the silicon drop, (B) adds both drops as if in series, (C) treats the diodes as ideal.

E8. NEET ยท MCQ Inputs $A$ and $B$ feed a NOR gate, whose output is $P$. Input $A$ and $P$ then feed a second NOR gate, whose output is $Y$. Then (A) $Y=\overline{A}\cdot B$ (B) $Y=A\cdot\overline{B}$ (C) $Y=\overline{A+B}$ (D) $Y=A+B$

Algebra $Y=\overline{A+P}=\overline{A}\cdot\overline{P}$ (De Morgan, Section 19.3), and $\overline{P}=\overline{\overline{A+B}}=A+B$. So $Y=\overline{A}\cdot(A+B)=\overline{A}A+\overline{A}B=\overline{A}\cdot B$.
Check $A=0$, $B=1$: $P=0$, $Y=\overline{0+0}=1$ โœ“; $A=1$: $Y=\overline{1+P}=0$ whatever $B$ is โœ“.
Answer (A).
โฑ Shortcut A NOR fed with $A=1$ is stuck at 0, so $Y$ can be 1 only with $A=0$ โ€” that leaves (A) and (C). Then try $A=0$, $B=1$: (A) gives 1, (C) gives 0, and the circuit gives 1.
โœ… Before you start
Semiconductors extend the ideas of current, drift velocity, mobility and resistivity (Section 12.1), and diode circuits are solved with Kirchhoff's laws (Section 12.2). The barrier of a junction is an electric field and a potential difference (Section 11.3). Rectifiers start from an alternating supply, so recall peak and rms values (Section 14.3). LEDs, photodiodes and solar cells exchange photons with the crystal, $E=hc/\lambda$ (Section 17.1), and energy bands grow out of the discrete energy levels of single atoms (Section 18.2). Logic gates need no physics at all โ€” only careful bookkeeping with $0$ and $1$.