11.4 Capacitors and Dielectrics
A capacitor is two conductors that hold equal and opposite charges: $C=Q/V$, $C=\varepsilon_0A/d$ for parallel plates, $K$ times more with a dielectric between them, and it stores energy $\tfrac12CV^2$ — which we follow through series and parallel networks and through the sharing of charge.
A camera flash charges for a second or two and then releases its energy in a thousandth of a second. A defibrillator stores a few hundred joules and delivers them through a patient's chest. The touch screen of a phone senses your finger because your finger changes how much charge tiny electrodes can hold. Every one of these uses a capacitor — two conductors separated by an insulator — and every one depends on the ideas of this section: how much charge a pair of conductors holds per volt, how an insulating material between them increases that, and how much energy is stored.
We start with what happens to an insulator in an electric field (it becomes polarised, and weakens the field inside it), then define capacitance and work it out for parallel plates with and without a dielectric slab, combine capacitors in series and in parallel, and finally find the energy stored — including the surprising energy loss when two charged capacitors are joined. We use the potential and the conductor results of § 11.3 and the field of a charged plane sheet from § 11.2. Capacitors are among the most predictable topics of NEET physics: $C=K\varepsilon_0A/d$, series and parallel networks (often drawn as a circuit), what happens to $Q$, $V$, $E$ and $U$ when a slab is inserted or the plates are moved — with the battery connected or not — and the energy $\tfrac12CV^2$, including the energy lost when charge is shared.
Conductors, insulators and dielectrics
In a conductor (a metal, a salt solution) some charges are free to move through the whole material. In an insulator (glass, mica, paper, plastic, dry air) every electron is bound to its own atom or molecule; it can be shifted a little, but not carried away. Put each in a uniform external field $\mathbf E_0$. In the conductor, free electrons drift until the charges induced on its surfaces produce a field that exactly cancels $\mathbf E_0$ inside — the field inside becomes zero (§ 11.3). In an insulator the charges can only shift slightly, so the induced charges cancel only part of the field. Insulators studied from this point of view are called dielectrics.
Polar and non-polar molecules. In a non-polar molecule (for example $\mathrm{O_2}$, $\mathrm{N_2}$, $\mathrm{H_2}$, $\mathrm{CO_2}$, $\mathrm{CH_4}$) the centre of the positive charges coincides with the centre of the negative charges, so the molecule has no dipole moment of its own. An external field pulls the two centres slightly apart and induces a small dipole moment along the field. A polar molecule (for example $\mathrm{H_2O}$, $\mathrm{HCl}$, $\mathrm{NH_3}$) has a permanent dipole moment, because its charge centres do not coincide. Without a field these dipoles point in random directions and their moments cancel; a field exerts a torque on each (§ 11.3, Result 11.21) and partly lines them up, against the jostling of thermal motion. Either way, the material ends up with a net dipole moment along the field.
A dielectric is an insulating material in which an electric field produces (or lines up) molecular dipoles. The electric polarisation $\mathbf P$ of a dielectric is its net dipole moment per unit volume (unit $\text{C/m}^2$). For most materials (linear, isotropic) $\mathbf P$ is proportional to the field inside: $\mathbf P=\varepsilon_0\chi\,\mathbf E$, where the dimensionless number $\chi$ is the electric susceptibility.
Why the field is reduced. Think of a dielectric slab placed with its faces perpendicular to $\mathbf E_0$. Inside the slab the shifted positive and negative charges still balance, but on the face towards which the field points a thin layer of positive charge is left uncovered, and on the opposite face a layer of negative charge. These bound (induced) surface charges have density $\sigma_b=P$. Like two oppositely charged sheets, they make a field $\sigma_b/\varepsilon_0$ inside the slab, pointing against $\mathbf E_0$. So the field inside is $E=E_0-P/\varepsilon_0=E_0-\chi E$, which gives $E=\dfrac{E_0}{1+\chi}$.
The dielectric constant (relative permittivity) $K$ of a material is the factor by which it reduces a field:
$$K=\frac{E_0}{E}=1+\chi=\frac{\varepsilon}{\varepsilon_0},$$where $\varepsilon=K\varepsilon_0$ is the permittivity of the material. $K=1$ for vacuum, $1.0006$ for air (taken as $1$), about $2$–$4$ for paper, plastics and oils, $5$–$10$ for glass and mica and $80$ for water; for a metal, $K\to\infty$. The dielectric strength of a material is the largest field it can withstand without breaking down (conducting): about $3\times10^6\ \text{V/m}$ for dry air and over $10^7\ \text{V/m}$ for mica.
When point charges are embedded in a large uniform medium of dielectric constant $K$ (filling all the space round them), the force, field and potential are all reduced by the factor $K$:
$$F=\frac{1}{4\pi\varepsilon_0K}\frac{q_1q_2}{r^2},\qquad E=\frac{kq}{Kr^2},\qquad V=\frac{kq}{Kr}.$$That is, replace $\varepsilon_0$ by $\varepsilon=K\varepsilon_0$. For a slab of dielectric in a uniform field $E_0$ (faces perpendicular to it): $E=E_0/K$ inside, and the bound charge density on its faces is $\sigma_b=P=\varepsilon_0(E_0-E)=\varepsilon_0E_0\left(1-\dfrac1K\right)$.
A slab of dielectric constant $K$ is placed in a uniform field $E_0$ with its faces perpendicular to the field. The field inside the slab is
Capacitors and the parallel-plate capacitor
Give a conductor a charge $Q$ and its potential rises in proportion: for an isolated sphere, $V=kQ/R$. The ratio $Q/V$ measures how much charge the conductor can take per volt. It is far more useful for a pair of conductors carrying equal and opposite charges, because then the field is concentrated in the space between them.
A capacitor is a system of two conductors (the plates), insulated from each other, carrying charges $+Q$ and $-Q$. If $V$ is the potential difference between them, the capacitance is
$$C=\frac{Q}{V}.$$Its SI unit is the farad: $1\ \text{F}=1\ \text{C/V}$ (practical sizes are $\mu\text{F}$, $\text{nF}$, $\text{pF}$). $C$ depends only on the size, shape and separation of the conductors and on the medium between them — not on $Q$ or $V$. The symbol is two parallel lines ⊣⊢. For a single isolated conductor, $C=Q/V$ with $V$ measured from infinity; an isolated sphere of radius $R$ has $C=4\pi\varepsilon_0R=R/k$.
Even the whole Earth, with $R=6.4\times10^6\ \text{m}$, has only $C=R/k=7.1\times10^{-4}\ \text{F}=711\ \mu\text{F}$ as an isolated sphere — the farad is a very large unit. Two plates close together do much better.
The parallel-plate capacitor. Take two flat metal plates of area $A$, a distance $d$ apart, with $d$ much smaller than the size of the plates. Charges $+Q$ and $-Q$ spread uniformly over their inner faces with densities $\pm\sigma$, $\sigma=Q/A$. Each sheet makes a field $\sigma/2\varepsilon_0$ (§ 11.2). Between the plates the two fields point the same way and add; outside they cancel:
$$E=\frac{\sigma}{\varepsilon_0}=\frac{Q}{\varepsilon_0A}\ \text{(between)},\qquad E=0\ \text{(outside)}.$$The field is uniform, so $V=Ed=\dfrac{Qd}{\varepsilon_0A}$, and $C=Q/V$:
For two parallel plates of area $A$ a distance $d$ apart in vacuum (or air), with $d$ small compared with the plate size so that the field is uniform between them and the bending of field lines at the edges ("fringing") can be ignored:
$$C_0=\frac{\varepsilon_0A}{d},\qquad E=\frac{\sigma}{\varepsilon_0}=\frac{V}{d}.$$$C$ grows with the area and falls as the plates move apart.
With a dielectric. Fill the whole gap with a dielectric of constant $K$, keeping the charge $Q$ fixed. The field between the plates drops to $E_0/K$, so $V$ drops to $V_0/K$ and the capacitance rises to $KC_0$ — this is in fact the best way to measure $K$. Now suppose the slab has thickness $t\lt d$ and the same area as the plates. With free charge density $\sigma$ on the plates, the field is $\sigma/\varepsilon_0$ in the air gaps (total thickness $d-t$) and $\sigma/K\varepsilon_0$ in the slab. Adding the potential drops,
$$V=\frac{\sigma}{\varepsilon_0}(d-t)+\frac{\sigma}{K\varepsilon_0}t=\frac{Q}{\varepsilon_0A}\left(d-t+\frac tK\right).$$For plates of area $A$ and separation $d$:
- gap completely filled with a dielectric of constant $K$: $\ C=\dfrac{K\varepsilon_0A}{d}=KC_0$;
- a dielectric slab of thickness $t$ (covering the full area, parallel to the plates): $\ C=\dfrac{\varepsilon_0A}{d-t+t/K}$;
- a metal slab of thickness $t$ (the limit $K\to\infty$): $\ C=\dfrac{\varepsilon_0A}{d-t}$.
The answer does not depend on where the slab sits between the plates. Each slab acts as if it shortened the gap: a dielectric by $t(1-1/K)$, a metal by its whole thickness $t$.
In Interactive 1 choose charged to 12 V, then isolated, and set $d=2.0\ \text{mm}$, $t=1.0\ \text{mm}$, $K=4$. When the slab is fully in, what is the voltage across the plates?
An air-filled parallel-plate capacitor is charged and then disconnected from the battery. Its plates are pulled apart until the gap is doubled. The potential difference between the plates
Combinations of capacitors
Capacitors are connected together to obtain a value not available on its own, or to share a high voltage between several capacitors so that none breaks down. Two basic ways of connecting them lead to simple rules. In each case the equivalent capacitance is the single capacitor that would store the same charge when connected across the same total voltage.
In parallel, one plate of each capacitor is joined to one terminal and the other plates to the other terminal, so all have the same potential difference $V$. The charges $Q_i=C_iV$ add: $Q=(C_1+C_2+\cdots)V$. In series, the capacitors are joined end to end. A charge $+Q$ put on the first plate induces $-Q$ on the facing plate; the isolated piece of conductor between two capacitors has zero net charge, so $+Q$ appears on the next plate, and so on. All carry the same charge $Q$, and the voltages $V_i=Q/C_i$ add: $V=Q\left(\dfrac1{C_1}+\dfrac1{C_2}+\cdots\right)$.
Parallel (same $V$, charges add, $Q_i\propto C_i$): $\qquad C=C_1+C_2+\cdots+C_n$.
Series (same $Q$, voltages add, $V_i\propto1/C_i$): $\qquad\dfrac1C=\dfrac1{C_1}+\dfrac1{C_2}+\cdots+\dfrac1{C_n}$.
For two in series, $C=\dfrac{C_1C_2}{C_1+C_2}$ and the supply voltage divides as $V_1=\dfrac{C_2}{C_1+C_2}V$, $V_2=\dfrac{C_1}{C_1+C_2}V$ — the smaller capacitor takes the larger share. A series combination is smaller than its smallest member; a parallel one is larger than its largest. $n$ equal capacitors $C$: $nC$ in parallel, $C/n$ in series.
Dielectric arrangements are combinations. If two dielectrics fill the gap side by side (each covering part of the plate area, each the full thickness), both parts have the same voltage: they are in parallel, $C=\dfrac{\varepsilon_0}{d}(K_1A_1+K_2A_2)$. If they are stacked in layers (each covering the whole area, thicknesses $t_1+t_2=d$), the same charge passes through both: they are in series, $\dfrac1C=\dfrac{1}{\varepsilon_0A}\left(\dfrac{t_1}{K_1}+\dfrac{t_2}{K_2}\right)$. The partial slab of Result 11.24 is just a layer of dielectric in series with a layer of air.
- Find groups that are clearly in parallel (both ends joined to the same two points) or in series (joined end to end with nothing else connected at the junction). Replace each group by its equivalent, and repeat.
- For the whole network, $Q_\text{total}=C_\text{eq}V$.
- Work back out: capacitors in series with the battery carry $Q_\text{total}$; across a parallel group, find the common voltage and then each charge $Q_i=C_iV_i$.
- Check: the voltages round any loop add up to the supply voltage, and the charges arriving at any junction balance.
- A bridge of five capacitors with $C_1/C_2=C_3/C_4$ is balanced: the middle capacitor carries no charge and can be removed.
You have three $2\ \mu\text{F}$ capacitors and must use all three. Which of these equivalent capacitances can you not make?
Energy stored and sharing of charge
Charging a capacitor means moving charge from one plate to the other against the growing voltage between them. Suppose at some moment the plates hold $\pm q$, so the voltage is $q/C$. Moving a further $dq$ needs work $dW=\dfrac{q}{C}\,dq$. Charging from $0$ to $Q$:
$$W=\int_0^Q\frac qC\,dq=\frac{Q^2}{2C}.$$This work is stored as electric potential energy, and it can be recovered when the capacitor discharges.
A capacitor of capacitance $C$ with charge $Q$ and voltage $V$ stores energy
$$U=\frac{Q^2}{2C}=\frac12CV^2=\frac12QV.$$For a parallel-plate capacitor, $U=\tfrac12(\varepsilon_0A/d)(Ed)^2=\tfrac12\varepsilon_0E^2\times(Ad)$, so the energy can be thought of as stored in the field, with energy density (energy per unit volume) $u=\tfrac12\varepsilon_0E^2$ — or $\tfrac12K\varepsilon_0E^2$ in a dielectric. The plates attract each other with force $F=\dfrac{Q^2}{2\varepsilon_0A}=\tfrac12QE$ (each plate feels the field $\sigma/2\varepsilon_0$ of the other only).
A battery of emf $V$ that charges an uncharged capacitor to $V$ supplies energy $QV=CV^2$; only half, $\tfrac12CV^2$, is stored. The other half is lost as heat in the connecting resistance (and radiation), however small the resistance.
Inserting a dielectric — two different situations. What happens to $Q$, $V$, $E$ and $U$ when a slab of constant $K$ is pushed in to fill the gap depends on whether the battery is still connected.
| quantity | battery connected ($V$ fixed) | isolated ($Q$ fixed) |
|---|---|---|
| capacitance | $KC_0$ | $KC_0$ |
| charge | $KQ_0$ | $Q_0$ |
| voltage | $V_0$ | $V_0/K$ |
| field between plates | $E_0$ | $E_0/K$ |
| energy stored | $KU_0$ | $U_0/K$ |
In both cases the slab is pulled in by the field. With the plates isolated, the energy that disappears, $U_0(1-1/K)$, is the work done on the slab. With the battery connected, the battery supplies $(K-1)Q_0V_0$: half goes into the extra stored energy and half into work on the slab.
Sharing of charge. Take a capacitor $C_1$ charged to $V_1$ and a capacitor $C_2$ charged to $V_2$, and join them — positive plate to positive plate, negative to negative. Charge flows until the two voltages are equal. No charge can leave the joined pair of upper plates, so the total charge on them is conserved: $C_1V_1+C_2V_2=(C_1+C_2)V$.
When $C_1$ (at $V_1$) and $C_2$ (at $V_2$) are joined with like plates together, the common potential and the energy lost are
$$V=\frac{C_1V_1+C_2V_2}{C_1+C_2},\qquad\Delta U=U_\text{before}-U_\text{after}=\frac{C_1C_2\,(V_1-V_2)^2}{2(C_1+C_2)}.$$If they are joined with opposite plates together, replace $V_2$ by $-V_2$: $V=\dfrac{C_1V_1-C_2V_2}{C_1+C_2}$ and $\Delta U=\dfrac{C_1C_2(V_1+V_2)^2}{2(C_1+C_2)}$. Charge is conserved, but energy is always lost (unless $V_1=V_2$): it becomes heat in the connecting wires and electromagnetic radiation. When $C_2$ is uncharged, the fraction lost is $\dfrac{C_2}{C_1+C_2}$.
In Interactive 2 set $C_1=3\ \mu\text{F}$ at $V_1=40\ \text{V}$ and $C_2=1\ \mu\text{F}$ uncharged ($V_2=0$), like plates together. What fraction of the stored energy is lost when the switch is closed?
(b) A $4\ \mu\text{F}$ capacitor charged to $100\ \text{V}$ is disconnected from the supply and connected across an identical uncharged capacitor. The energy lost in the process is (A) zero (B) $0.005\ \text{J}$ (C) $0.01\ \text{J}$ (D) $0.02\ \text{J}$.
1. Battery connected or not? Read the question twice. Connected: $V$ stays fixed, so $Q=CV$ and $U=\tfrac12CV^2$ rise and fall with $C$. Disconnected (isolated): $Q$ stays fixed, so $V=Q/C$ and $U=Q^2/2C$ fall when $C$ rises. Most wrong answers about inserting a slab or moving the plates mix the two.
2. Series and parallel the wrong way round. Capacitors in parallel add (like resistors in series); in series their reciprocals add. Series capacitors carry the same charge, and the smaller capacitor takes the larger share of the voltage.
3. Capacitance is geometry and medium only. $C=K\varepsilon_0A/d$ does not depend on $Q$ or $V$; "$C\propto Q$" in a statement is false. A partial slab gives $\dfrac{\varepsilon_0A}{d-t+t/K}$, not $KC_0$; a metal slab gives $\dfrac{\varepsilon_0A}{d-t}$.
4. Energy is not conserved when charge is shared. The common voltage comes from conservation of charge; the energy afterwards is always less. A battery that charges a capacitor supplies $CV^2$ and only half of it is stored.
5. The field in a dielectric. A slab of dielectric constant $K$ reduces the field inside it to $E_0/K$; it does not make it zero (only a metal does). Polar molecules ($\mathrm{H_2O}$, $\mathrm{HCl}$, $\mathrm{NH_3}$) have permanent dipole moments; non-polar ones ($\mathrm{O_2}$, $\mathrm{CO_2}$, $\mathrm{CH_4}$) acquire induced moments only in a field.
6. Units. $\mu\text{F}\times\text{V}=\mu\text{C}$ and $\mu\text{F}\times\text{V}^2=\mu\text{J}$; areas in $\text{m}^2$ ($100\ \text{cm}^2=0.010\ \text{m}^2$), gaps in metres. Parallel plates of laboratory size have capacitances of picofarads.
A parallel-plate capacitor stays connected to a battery while its plate separation is doubled. The energy stored in it
Exercises
Take $\varepsilon_0=8.85\times10^{-12}\ \text{C}^2\text{N}^{-1}\text{m}^{-2}$ and $k=9.0\times10^9\ \text{N m}^2\text{C}^{-2}$; the medium is air ($K=1$) unless stated.
- 1 A capacitor holds $60\ \mu\text{C}$ when connected across $12\ \text{V}$. Find its capacitance.
- 2 Find the capacitance of two circular plates of radius $6.0\ \text{cm}$, $2.0\ \text{mm}$ apart.
- 3 Find the capacitance of an isolated metal sphere of radius $9.0\ \text{cm}$.
- 4 What plate separation gives $1.0\ \text{nF}$ with plates of area $0.050\ \text{m}^2$?
- 5 Air breaks down at $3.0\times10^6\ \text{V/m}$. Find the largest voltage and the largest charge for the capacitor of part 2.
- 6 A slab with $K=5.0$ is placed in a uniform field of $1.0\times10^5\ \text{V/m}$, faces perpendicular to the field. Find the field inside and the bound surface charge density.
- 7 Give two examples each of polar and non-polar molecules, and describe how each kind responds to an applied field.
- 8 Two charges repel with $0.80\ \text{N}$ in air and with $0.32\ \text{N}$ when immersed, at the same separation, in a large volume of oil. Find the dielectric constant of the oil.
- 1 Find its capacitance in air.
- 2 Find its capacitance when the gap is completely filled with a material of $K=6.0$.
- 3 Find its capacitance with a slab of $K=6.0$ and thickness $1.5\ \text{mm}$ (full area) in the gap.
- 4 Find its capacitance with a metal slab $1.5\ \text{mm}$ thick (full area) in the gap.
- 5 Explain why, in parts 3 and 4, it does not matter whether the slab touches one plate or sits in the middle.
- 6 A slab $2.0\ \text{mm}$ thick raises the capacitance to $1.5$ times its air value. Find its dielectric constant.
- 7 Find the capacitance when half of the plate area is filled across the full gap with a material of $K=5.0$, the other half being air.
- 8 In the arrangement of part 3 the capacitor is connected to $100\ \text{V}$. Find the field in the air gap and in the slab.
- 1 Find the equivalent capacitance of $2.0$, $3.0$ and $6.0\ \mu\text{F}$ in series.
- 2 Find the equivalent capacitance of the same three in parallel.
- 3 The series combination of part 1 is connected across $12\ \text{V}$. Find the charge on each capacitor and the voltage across the $2.0\ \mu\text{F}$ one.
- 4 Capacitors of $4\ \mu\text{F}$ can each safely take $100\ \text{V}$. What is the least number needed to make a combination of $4\ \mu\text{F}$ that can take $300\ \text{V}$?
- 5 A $4.0\ \mu\text{F}$ and a $12\ \mu\text{F}$ capacitor in series are connected in parallel with a $2.0\ \mu\text{F}$ capacitor across $20\ \text{V}$. Find the charge on the $12\ \mu\text{F}$ capacitor.
- 6 In a bridge, $C_1=2.0$ and $C_2=4.0\ \mu\text{F}$ are in series on one branch, $C_3=3.0$ and $C_4=6.0\ \mu\text{F}$ in series on the other, and a $5.0\ \mu\text{F}$ capacitor joins the two junctions. Find the equivalent capacitance between the ends.
- 7 Two capacitors have an equivalent capacitance of $9.0\ \mu\text{F}$ in parallel and $2.0\ \mu\text{F}$ in series. Find them.
- 8 Explain why capacitors in series carry equal charges even when their capacitances differ.
- 1 Find the energy stored in a $50\ \mu\text{F}$ capacitor charged to $200\ \text{V}$.
- 2 Find the energy density in air where the field is $2.0\times10^5\ \text{V/m}$.
- 3 An $8.0\ \mu\text{F}$ capacitor is charged to $100\ \text{V}$ and disconnected. A slab with $K=4.0$ is pushed in to fill the gap. Find the new voltage and the new stored energy (in mJ).
- 4 Repeat part 3 with the battery left connected. Find the new stored energy and the energy supplied by the battery during the insertion.
- 5 A $6.0\ \mu\text{F}$ capacitor charged to $120\ \text{V}$ is connected to an uncharged $3.0\ \mu\text{F}$ capacitor. Find the common voltage and the energy lost.
- 6 A $12\ \text{V}$ battery charges an uncharged $5.0\ \mu\text{F}$ capacitor through a resistor. Find the energy supplied by the battery and the heat produced.
- 7 The plates of an isolated capacitor of area $0.010\ \text{m}^2$ carry $\pm0.20\ \mu\text{C}$. Find the force of attraction between them.
- 8 Capacitors of $2.0\ \mu\text{F}$ at $100\ \text{V}$ and $3.0\ \mu\text{F}$ at $50\ \text{V}$ are joined with opposite plates together. Find the common voltage and the energy lost.
E1. NEET · MCQ An air-filled parallel-plate capacitor has capacitance $5\ \mu\text{F}$. The separation between its plates is doubled and the space between them is completely filled with a dielectric of dielectric constant $4$. The new capacitance is (A) $40\ \mu\text{F}$ (B) $10\ \mu\text{F}$ (C) $2.5\ \mu\text{F}$ (D) $20\ \mu\text{F}$
E2. NEET · MCQ Statement I: When a dielectric slab is inserted between the plates of a charged capacitor that has been disconnected from the battery, the energy stored in the capacitor decreases. Statement II: Capacitors connected in series all have the same potential difference across them. In the light of these statements, choose the correct option. (A) Both Statement I and Statement II are correct (B) Both Statement I and Statement II are incorrect (C) Statement I is correct but Statement II is incorrect (D) Statement I is incorrect but Statement II is correct
E3. NEET · MCQ Assertion (A): Placing an uncharged metal slab of thickness $d/2$ between the plates of a parallel-plate capacitor of plate separation $d$, parallel to the plates, doubles its capacitance. Reason (R): The electric field inside the metal slab is zero, so the whole potential difference appears across the remaining gap of total thickness $d/2$. Choose the correct option. (A) Both A and R are true and R is the correct explanation of A (B) Both A and R are true but R is not the correct explanation of A (C) A is true but R is false (D) A is false but R is true
E4. NEET · MCQ Two identical capacitors each have capacitance $C$, and $V$ is a potential difference. Match List-I with List-II.
List-I: (a) the equivalent capacitance of the two in series (b) the equivalent capacitance of the two in parallel (c) the energy stored in one capacitor charged to $V$ (d) the charge on one capacitor charged to $V$
List-II: (i) $2C$ (ii) $\dfrac C2$ (iii) $CV$ (iv) $\tfrac12CV^2$
Choose the correct answer: (A) a-i, b-ii, c-iv, d-iii (B) a-ii, b-i, c-iv, d-iii (C) a-ii, b-iv, c-i, d-iii (D) a-ii, b-i, c-iii, d-iv
E5. NEET · MCQ In the circuit shown, the capacitors are initially uncharged and the battery has been connected for a long time. The charge on the $3\ \mu\text{F}$ capacitor is (A) $24\ \mu\text{C}$ (B) $12\ \mu\text{C}$ (C) $36\ \mu\text{C}$ (D) $18\ \mu\text{C}$
E6. NEET · MCQ How many of the following statements are correct?
(i) The capacitance of a parallel-plate capacitor is directly proportional to the charge on its plates.
(ii) Filling the gap of a parallel-plate capacitor with a dielectric increases its capacitance.
(iii) The energy stored per unit volume in the field between the plates of an air capacitor is $\tfrac12\varepsilon_0E^2$.
(iv) When two charged capacitors at different voltages are joined, the total charge is conserved but the stored energy decreases.
(v) The equivalent capacitance of capacitors in series is greater than the largest of them.
(A) One (B) Two (C) Three (D) Four
Research question. Does a home-made capacitor of kitchen foil and paper obey $C=K\varepsilon_0A/d$, and what is the dielectric constant of the paper?
Why it matters. Capacitive sensing is everywhere: phone and tablet touch screens, fuel-level gauges in aircraft, humidity sensors in weather stations, and the soil-moisture probes that let farmers in dry regions water only when crops need it. All of them work because a capacitance changes when the gap or the dielectric between two electrodes changes (Result 11.24). Measuring the dielectric constant of a material is also a standard test in the electrical industry — for cable insulation, circuit boards and the films inside the capacitors of electric-vehicle inverters.
What to do.
- Cut two rectangles of aluminium foil, about $15\ \text{cm}\times20\ \text{cm}$, each with a tab for connection. Measure the thickness of one sheet of printer paper by measuring a stack of $100$ sheets with a ruler or screw gauge.
- Place one, two, three, … up to eight sheets of paper between the foils, with a heavy book on top to press them flat. Measure the capacitance each time with a multimeter that has a capacitance range.
- Plot $C$ against $1/d$ (where $d$ is the total paper thickness). Is it a straight line? Find its slope, and from it $K=\text{slope}/(\varepsilon_0A)$.
- Repeat with a plastic sheet or a thin sheet of glass of the same total thickness and compare.
- Measure the capacitance with the foils slightly offset so that they overlap over only half the area. Does $C$ halve?
Tools: Aluminium foil, printer paper, a ruler or screw gauge, a multimeter with a capacitance range (or a simple RC timing circuit with a stopwatch), books for weight, a spreadsheet for the graph.
Hand in: Your table of $C$ and $d$, the graph of $C$ against $1/d$ with the fitted line, your value of $K$ for paper with an uncertainty, and a paragraph on the main sources of error (air gaps, edges, how hard the sheets are pressed).
Going further. Hold a hand flat a few millimetres above (not touching) the top foil and watch the reading. Explain the change — this is the principle of a touch sensor.
🧪 Self-check quiz
Q1. A capacitor holds a charge of $20\ \mu\text{C}$ when the potential difference across it is $5\ \text{V}$. Its capacitance is
Q2. A $2\ \mu\text{F}$ and a $3\ \mu\text{F}$ capacitor are joined in series, and this pair is connected in parallel with a $0.8\ \mu\text{F}$ capacitor. The equivalent capacitance is
Q3. The energy stored in a $10\ \mu\text{F}$ capacitor charged to $200\ \text{V}$ is
Q4. A parallel-plate capacitor holding charge $Q$ stays connected to its battery while a dielectric of dielectric constant $4$ is slid in to fill the gap completely. The charge on the capacitor becomes
Q5. Which of these molecules has a permanent electric dipole moment?