Chapter 7 · Introduction

Chapter 7 — Properties of Solids and Liquids

Real solids stretch and real fluids flow. This chapter measures how solids resist deformation, how pressure builds up in a fluid at rest and changes in one that moves, why a liquid surface behaves like a stretched skin, and how heat expands, warms, melts and travels through matter.

A monsoon raindrop falls from a cloud two kilometres up. With no air it would hit the ground at about $200\ \text{m/s}$, faster than a bullet from an air rifle; in fact it lands at a few metres per second and does no harm. A mechanic lifts a car with one hand on a hydraulic jack. A steel ship floats while a steel needle sinks — yet a dry needle laid gently on water can rest on the surface. Railway lines are laid with gaps between the rails, a bridge rests on rollers at one end, and the steel cables of a lift are chosen so that they stretch, but only a little. Ice cubes cool a drink far more than the same mass of cold water, and a vacuum flask keeps tea hot for hours.

All of these belong to the properties of bulk matter, the widest unit of the NEET (UG) physics syllabus. You will first see how solids resist stretching, squeezing and shearing (elasticity: stress, strain and the three moduli). Then fluids at rest: pressure that grows with depth, Pascal's law and Archimedes' principle. Then fluids in motion: the equation of continuity, Bernoulli's principle, and viscosity, which sets the terminal velocity of that raindrop. Then the liquid surface itself: surface tension, the extra pressure inside drops and bubbles and the rise of water in a thin tube. Finally heat: thermal expansion, calorimetry and change of state, and heat transfer by conduction, convection and radiation — which lead straight into thermodynamics in Chapter 8.

NEET sets questions on this unit every year, almost always as short MCQs: a ratio of extensions or the energy stored in a stretched wire; a U-tube, a hydraulic lift or a floating block; a speed of efflux or the $r^2$ law of terminal velocity; the excess pressure in a drop or a bubble and the height of capillary rise; a calorimetry, conduction or radiation ratio. The NEET (UG) syllabus for the unit — elastic behaviour, Hooke's law and the three moduli; pressure due to a fluid column, the effect of gravity on it and Pascal's law; viscosity, Stokes' law, terminal velocity, streamline and turbulent flow, critical velocity and Bernoulli's principle; surface energy and surface tension, the angle of contact, excess pressure, drops, bubbles and capillary rise; heat, temperature, thermal expansion, specific heat capacity, calorimetry, latent heat and the three modes of heat transfer — is covered by the five sections below.

Stress & strain→Hooke's law & moduli→$p=p_0+\rho gh$→Pascal & Archimedes→Continuity & Bernoulli→Viscosity & terminal velocity→Surface tension→Excess pressure & capillary rise→Expansion & calorimetry→Conduction & radiation
🎯 By the end of this chapter you can…
  • define stress, strain, Young's modulus, bulk modulus and modulus of rigidity, read the stress–strain curve, and find the extension and the stored elastic energy of wires, including wires in series and wires stretched by their own weight;
  • find the pressure at a depth in a liquid, convert between gauge and absolute pressure, use barometers and U-tube manometers, and find the force on a dam and the pressure in an accelerating liquid;
  • apply Pascal's law to hydraulic machines and Archimedes' principle to floating and immersed bodies, apparent weight and relative density;
  • use the equation of continuity and Bernoulli's principle for pipes, the speed of efflux, the Venturi meter and dynamic lift;
  • use the coefficient of viscosity, Stokes' law and the terminal velocity of a sphere, and tell streamline from turbulent flow with the Reynolds number and the critical velocity;
  • use surface tension and surface energy for films, drops and bubbles, the angle of contact, the excess pressures $\dfrac{2S}{R}$ and $\dfrac{4S}{R}$, and the capillary rise $h=\dfrac{2S\cos\theta}{\rho gr}$;
  • convert between temperature scales and calculate linear, area and volume expansion, thermal stress and the error of a pendulum clock;
  • solve calorimetry problems with specific and latent heats, including ice–water mixtures in which the final state must first be found;
  • calculate the rate of conduction through single and composite slabs, and radiated power with the Stefan–Boltzmann and Wien laws;
  • solve NEET multiple-choice questions that mix all five sections in every format the paper uses — single answer, statement I / II, assertion–reason, matching lists, "how many are correct" and graph reading — quickly, by eliminating options.

In the teaser below a tank on the ground is kept filled with water to a depth of $2.0\ \text{m}$, and you can open a small hole in its side at any height. Which hole throws its jet farthest along the ground?

Set $h=0.10\ \text{m}$: gauge pressure $18.6\ \text{kPa}$, jet speed $6.10\ \text{m/s}$, but range only $0.87\ \text{m}$ — the water reaches the ground almost at once. At $h=1.00\ \text{m}$ the readouts show $9.8\ \text{kPa}$, $4.43\ \text{m/s}$ and the largest range, $2.00\ \text{m}$. At $h=0.50\ \text{m}$ and $h=1.50\ \text{m}$ the range is the same, $1.73\ \text{m}$. The jet speed comes from pressure (or Bernoulli), $v=\sqrt{2g(H-h)}$, the time of fall from $h=\tfrac12gt^2$, and their product $x=2\sqrt{h(H-h)}$ is greatest when $h=H-h$, i.e. halfway up, where it equals $H$.
Teaser — Holes in a Water Tank

A tank standing on level ground is kept full to a depth $H=2.0\ \text{m}$ by a tap. Choose the height $h$ of a small hole in its side: the pressure at the hole sets the speed of the jet, and the height sets how long the water takes to reach the ground. Each height you try leaves a dot where its jet lands. ($\rho=1000\ \text{kg/m}^3$, $g=9.8\ \text{m/s}^2$.)

0.30 m
gauge pressure at the hole, ρg(H − h)—
speed of the jet, √(2g(H − h))—
time to reach the ground—
range along the ground—

Sections in this chapter

🎯 Chapter mixed test NEET · MCQ

Eight NEET-style questions that hop between all five sections in no fixed order, as the paper does — and three of them need ideas from more than one section. Answer each one and press Submit (NEET marking: $+4$ correct, $-1$ wrong, $0$ unanswered), or press ⏱ Take as a timed test. The test clock is generous: at real NEET pace — about a minute per question — you should finish all eight in ten minutes, so try to beat it comfortably. Try them before you open any solution.

E1. NEET · MCQ Two wires A and B of the same material have lengths in the ratio $1:2$ and diameters in the ratio $2:1$. They are stretched by equal forces, within the proportional limit. The ratio of the elastic energies stored, $U_A:U_B$, is (A) $1:8$ (B) $1:4$ (C) $8:1$ (D) $1:2$

Formula With equal forces use $U=\dfrac{F^2L}{2AY}\propto\dfrac{L}{d^2}$ (Section 7.1).
Ratio $\dfrac{U_A}{U_B}=\dfrac{L_A}{L_B}\cdot\dfrac{d_B^2}{d_A^2}=\dfrac12\times\dfrac14=\dfrac18$.
Answer (A) $1:8$.
⏱ Shortcut A is shorter and thicker, so it stretches less and stores less: (C) is out. (B) forgets the length, (D) forgets the diameter.

E2. NEET · MCQ Statement I: The excess pressure inside a soap bubble of radius $R$ and surface tension $S$ is $\dfrac{2S}{R}$. Statement II: The height to which water rises in a clean glass capillary tube is inversely proportional to the radius of the tube. In the light of these statements, choose the correct option. (A) Both Statement I and Statement II are correct (B) Both Statement I and Statement II are incorrect (C) Statement I is correct but Statement II is incorrect (D) Statement I is incorrect but Statement II is correct

Statement I A soap bubble has two surfaces, inside and outside, so its excess pressure is $\dfrac{4S}{R}$; $\dfrac{2S}{R}$ belongs to a drop, which has one (Section 7.4). Incorrect.
Statement II $h=\dfrac{2S\cos\theta}{\rho gr}\propto\dfrac1r$. Correct.
Answer (D).
⏱ Shortcut Count the surfaces: a drop or an air bubble inside a liquid has one ($2S/R$), a soap bubble in air two ($4S/R$).

E3. NEET · MCQ Ice at $-40\ ^\circ\text{C}$ is heated at a constant rate until the water formed begins to boil; the graph shows its temperature against time. Taking the specific heat of water as $4200\ \text{J kg}^{-1}\text{K}^{-1}$, the specific latent heat of fusion of ice given by the graph is (A) $3.4\times10^4\ \text{J/kg}$ (B) $3.36\times10^5\ \text{J/kg}$ (C) $4.2\times10^5\ \text{J/kg}$ (D) $1.68\times10^5\ \text{J/kg}$
021020−40−20020406080100time t (min)temperature (°C)ABCD

Read the graph BC (melting at $0\ ^\circ\text{C}$) lasts $10-2=8\ \text{min}$; CD (water warming by $100\ \text{K}$) lasts $20-10=10\ \text{min}$. The heater supplies the same heat every minute.
Compare heats Per kilogram, $\dfrac{L_f}{c_w\times100}=\dfrac{8}{10}$, so $L_f=0.8\times4200\times100=3.36\times10^5\ \text{J/kg}$ (Section 7.5).
Answer (B) $3.36\times10^5\ \text{J/kg}$.
⏱ Shortcut Heat ∝ time on such a graph. (C) uses the whole $10\ \text{min}$ for melting; (D) mixes the specific heat of ice (the graph gives $2100\ \text{J kg}^{-1}\text{K}^{-1}$: $40\ \text{K}$ in $2\ \text{min}$, twice water's rate) with water's heating time.

E4. NEET · MCQ Assertion (A): A small steel ball dropped into a tall jar of oil soon falls with a constant speed. Reason (R): The buoyant force on the ball increases with its speed until it balances the ball's weight. Choose the correct option. (A) Both A and R are true and R is the correct explanation of A (B) Both A and R are true but R is not the correct explanation of A (C) A is true but R is false (D) A is false but R is true

Assertion The ball reaches its terminal velocity within milliseconds (Section 7.3). True.
Reason The buoyant force $\tfrac43\pi r^3\sigma g$ depends only on the volume displaced (Section 7.2), not on the speed. It is the viscous drag $6\pi\eta rv$ that grows until drag $+$ buoyancy $=$ weight. False.
Answer (C).
⏱ Shortcut Of the three forces on a falling sphere, only the drag depends on the speed.

E5. NEET · MCQ Match List-I with List-II ($S$ is the surface tension).
List-I: (a) excess pressure inside a liquid drop of radius $R$ (b) excess pressure inside a soap bubble of radius $R$ (c) height of capillary rise in a tube of radius $r$ (d) work done in increasing the area of a soap film by $\Delta A$
List-II: (i) $\dfrac{2S}{R}$ (ii) $\dfrac{4S}{R}$ (iii) $\dfrac{2S\cos\theta}{\rho gr}$ (iv) $2S\,\Delta A$
Choose the correct answer: (A) a-i, b-ii, c-iii, d-iv (B) a-ii, b-i, c-iii, d-iv (C) a-i, b-ii, c-iv, d-iii (D) a-i, b-iv, c-iii, d-ii

Match (a) one surface: $2S/R$ (i). (b) two surfaces: $4S/R$ (ii). (c) Jurin's law (iii). (d) a film has two faces, so its surface energy grows by $S\times2\Delta A$ (iv) (Section 7.4).
Answer (A).
⏱ Shortcut Only (iii) has the dimensions of a length and only (iv) of an energy, which fixes (c) and (d) and removes (C) and (D); "drop = one surface" removes (B).

E6. NEET · MCQ Two rods of the same length and cross-section, with thermal conductivities $K$ and $2K$, are joined end to end and lagged along their sides. The free end of the rod of conductivity $K$ is kept at $100\ ^\circ\text{C}$ and the free end of the other rod at $0\ ^\circ\text{C}$. In the steady state, the temperature of the junction is (A) $50\ ^\circ\text{C}$ (B) $66.7\ ^\circ\text{C}$ (C) $25\ ^\circ\text{C}$ (D) $33.3\ ^\circ\text{C}$

Same heat current In the steady state the same heat flows through both rods each second (Section 7.5): $\dfrac{KA(100-T)}{L}=\dfrac{2KA(T-0)}{L}$.
Solve $100-T=2T$, so $T=\dfrac{100}{3}=33.3\ ^\circ\text{C}$.
Answer (D) $33.3\ ^\circ\text{C}$.
⏱ Shortcut The poorer conductor takes the larger share of the temperature drop — here two thirds of $100\ ^\circ\text{C}$. (A) treats the rods as equal; (B) gives the larger drop to the better conductor.

E7. NEET · MCQ A metal block of relative density $8.0$ hangs from a steel wire, which is stretched by $0.80\ \text{mm}$. The block is then completely immersed in water, the wire staying out of the water. The extension of the wire becomes (A) $0.10\ \text{mm}$ (B) $0.70\ \text{mm}$ (C) $0.80\ \text{mm}$ (D) $0.91\ \text{mm}$

Buoyancy The buoyant force is $\rho_wVg=\dfrac{W}{8}$, so the tension falls to $\dfrac78W$ (Section 7.2).
Hooke The extension is proportional to the tension (Section 7.1): $0.80\times\dfrac78=0.70\ \text{mm}$.
Answer (B) $0.70\ \text{mm}$.
⏱ Shortcut The water can only reduce the pull on the wire, which removes (C) and (D); (A) is the change, not the new extension.

E8. NEET · MCQ How many of the following statements are correct?
(i) A perfectly incompressible liquid would have an infinite bulk modulus.
(ii) A hydraulic press multiplies force but not energy.
(iii) Bernoulli's equation applies unchanged to the turbulent flow of a viscous liquid.
(iv) The surface tension of a liquid generally decreases as its temperature rises.
(v) Heat can travel through a vacuum by convection.
(A) One (B) Two (C) Three (D) Four

Check each (i) ✓ — $B=-\Delta p/(\Delta V/V)$ with $\Delta V=0$ (Section 7.1). (ii) ✓ — $F_1d_1=F_2d_2$ (Section 7.2). (iii) ✗ — Bernoulli assumes steady, non-viscous flow (Section 7.3). (iv) ✓ — Section 7.4. (v) ✗ — convection needs a moving fluid; only radiation crosses a vacuum (Section 7.5).
Answer (C) three statements, (i), (ii) and (iv).
⏱ Shortcut One statement per section is a typical NEET mix: answer each from its own section's key idea and mark ✓ / ✗ as you go.
✅ Before you start
Most of this chapter is Newton's laws applied to matter in bulk, so revise forces in equilibrium and free-body diagrams (Section 3.1, Section 3.2) — buoyancy, viscous drag and terminal velocity are all force balances. Bernoulli's principle is the work–energy theorem for a moving fluid, and the energy of a stretched wire is the spring energy $\tfrac12kx^2$, so you need Section 4.1 and Section 4.2; a jet of water from a tank is a horizontal projectile (Section 2.3). Stokes' law is a classic dimensional-analysis result (Section 1.2), and the laboratory methods here (Young's modulus, capillary rise, viscosity by a falling ball, the method of mixtures) use the error analysis of Section 1.3. From Class 9 and 10 science, recall density, pressure, flotation, and the idea of heat and temperature.