Chapter 12 · Current Electricity

12.2 Cells, Combinations of Resistors and Kirchhoff's Laws

Real circuits join resistors in series and in parallel, use cells that have an emf $\varepsilon$ and an internal resistance $r$ (so the terminal voltage is $V=\varepsilon-Ir$), and combine several cells. Kirchhoff's two laws — charge is conserved at a junction, energy round a loop — solve any such network.

A torch has two or three cells end to end; a car's battery is six cells in one box; the lights in a house are all connected so that each gets the full mains voltage, while the bulbs of a cheap decorative string share it. Look closely at any of these and two questions keep coming up: how do several resistors or cells act together, and why does a battery's voltage drop when it is working hard — why do the headlights dim while the starter motor turns?

This section answers both. We find the single resistance equivalent to resistors in series and in parallel, and learn to reduce a network step by step. We then look inside a cell: its emf $\varepsilon$ and internal resistance $r$ explain why its terminal voltage depends on the current, and when it delivers the most power. After combining cells in series and in parallel, we finish with Kirchhoff's laws, which solve circuits that cannot be reduced to series and parallel at all. NEET draws several questions a year from this section: equivalent resistances (including wires that are cut, joined or bent into loops), the terminal voltage of a cell that is discharging or being charged, reversed and parallel cells, maximum power transfer, and short two-battery problems that Kirchhoff's laws — or the node method — settle in a few lines.

Resistors in series and in parallel

Throughout this section connecting wires are taken to have zero resistance, so every point along a plain wire is at the same potential. Points joined by a plain wire are electrically one point — a node — however the wire is drawn.

📘 Definition 12.9 — Equivalent resistance

The equivalent resistance of a combination of resistors between two terminals A and B is the single resistance $R_\text{eq}$ that would draw the same current $I$ from the same potential difference $V_{AB}$: $R_\text{eq}=V_{AB}/I$.

Series. Resistors are in series when they are joined end to end with no branch between them, so that the same current $I$ passes through each. The potential drops across them add: $V=IR_1+IR_2+\dots+IR_n$, that is, $V=I(R_1+\dots+R_n)$.

Parallel. Resistors are in parallel when each is connected directly between the same two nodes, so that each has the same potential difference $V$ across it. The currents through them add (charge is conserved at the node): $I=\dfrac{V}{R_1}+\dfrac{V}{R_2}+\dots$.

📐 Result 12.6 — Resistors in series
$$R_\text{eq}=R_1+R_2+\dots+R_n .$$

The current is common and the voltage divides in proportion to the resistances: $V_k=\dfrac{R_k}{R_\text{eq}}V$ (a potential divider). $R_\text{eq}$ is larger than the largest resistor; $n$ equal resistors $R$ give $nR$.

📐 Result 12.7 — Resistors in parallel
$$\frac1{R_\text{eq}}=\frac1{R_1}+\frac1{R_2}+\dots+\frac1{R_n}.$$

The voltage is common and the current divides in inverse proportion to the resistances. For two resistors $R_\text{eq}=\dfrac{R_1R_2}{R_1+R_2}$ and the current divides as $I_1=\dfrac{R_2}{R_1+R_2}I$, $\ I_2=\dfrac{R_1}{R_1+R_2}I$ (a current divider). $R_\text{eq}$ is smaller than the smallest resistor; $n$ equal resistors $R$ give $R/n$.

In series the larger resistor takes the larger share of the voltage and of the power ($P=I^2R$); in parallel the smaller resistor takes the larger share of the current and of the power ($P=V^2/R$). Two useful special results: a wire of resistance $R$ cut into $n$ equal pieces gives pieces of $R/n$, and those pieces in parallel give $R/n^2$; a uniform wire bent into a closed loop is two arcs in parallel between any two points on it.

🧭 Problem-solving strategy — Reducing a resistor network
  1. Label the nodes. Every point joined by plain wire gets the same label; a resistor with both ends at the same node is short-circuited and carries no current — remove it.
  2. Redraw the network between the two terminals with the nodes in a row. Resistors joining the same pair of nodes are in parallel; a chain through nodes with nothing else attached is in series.
  3. Replace the innermost series or parallel groups first, redraw and repeat.
  4. If the network is symmetric about the line joining the terminals, points that are mirror images are at the same potential; a resistor between two such points carries no current and may be removed.
  5. Work back out with the current and voltage dividers to find the current through, or the voltage across, any single resistor.
✏️ Example 1 — A three-resistor network
A $6\ \Omega$ and a $3\ \Omega$ resistor are connected in parallel, and the pair is connected in series with a $4\ \Omega$ resistor across an ideal $12\ \text{V}$ battery. Find (a) the equivalent resistance, (b) the current from the battery, (c) the current in each resistor, and (d) the power dissipated in each.
(a) $6\parallel3=\dfrac{6\times3}{6+3}=2\ \Omega$; in series with $4\ \Omega$: $R_\text{eq}=6\ \Omega$.
(b) $I=\dfrac{12}{6}=2.0\ \text{A}$, all of which passes through the $4\ \Omega$ resistor.
(c) The pair has $V=2.0\times2=4.0\ \text{V}$ across it: $I_6=\dfrac{4.0}{6}=0.67\ \text{A}$, $\ I_3=\dfrac{4.0}{3}=1.33\ \text{A}$. (Current divider: $I_6=\dfrac{3}{9}\times2.0$ ✓.)
(d) $P_4=2.0^2\times4=16\ \text{W}$, $\ P_6=\dfrac{4.0^2}{6}=2.7\ \text{W}$, $\ P_3=\dfrac{4.0^2}{3}=5.3\ \text{W}$.
Check Total $16+2.67+5.33=24\ \text{W}=VI=12\times2.0$ ✓.
✏️ Example 2 — A wire bent into a circle
A uniform wire of resistance $12\ \Omega$ is bent into a circle. Find the resistance between (a) the ends of a diameter, (b) two points on the circle that subtend a right angle at the centre. (c) The same wire, straight, is instead cut into four equal pieces that are joined in parallel. Find the resistance of the bundle.
(a) Two semicircles of $6\ \Omega$ in parallel: $R=3.0\ \Omega$.
(b) The arcs are a quarter and three quarters of the wire: $3\ \Omega$ and $9\ \Omega$ in parallel, $R=\dfrac{3\times9}{12}=2.25\ \Omega$.
(c) Each piece is $3\ \Omega$; four in parallel give $\dfrac34=0.75\ \Omega=\dfrac{12}{4^2}$.
⏱ Shortcut For arcs that are fractions $f$ and $1-f$ of a loop of resistance $R$: $R_{AB}=f(1-f)R$. It is largest, $R/4$, for a diameter.

Three identical resistors $R$ are connected so that two of them are in parallel and the third is in series with that pair. The equivalent resistance is

Emf, internal resistance and terminal voltage

A cell keeps charge flowing round a circuit. Outside the cell, positive charge moves from the high-potential terminal to the low one, losing potential energy in the resistors. Inside the cell it must be carried back "uphill", from the negative terminal to the positive one, against the electric field. That needs a non-electrostatic force — in a chemical cell it comes from the chemical reactions at the electrodes — which does work on the charge.

📘 Definition 12.10 — Electromotive force (emf)

The emf $\varepsilon$ of a source is the work done by its non-electrostatic forces per unit charge carried from its negative to its positive terminal inside it: $\varepsilon=W/q$. Its unit is the volt. Despite the name it is not a force. On open circuit (no current) the potential difference between the terminals equals the emf.

📘 Definition 12.11 — Internal resistance

The internal resistance $r$ of a cell is the resistance of the material inside it (electrolyte and electrodes) to the current flowing through the cell. A real cell behaves like an ideal emf $\varepsilon$ in series with a resistor $r$. For a fresh dry cell $r$ is a fraction of an ohm; a car battery has $r$ of a few hundredths of an ohm; $r$ grows as a cell ages.

Connect the cell to an external resistor $R$. The same current flows through $R$ and through $r$, so the emf is shared between the two: $\varepsilon=IR+Ir$. The voltage the outside circuit sees — the terminal voltage — is what is left after the drop $Ir$ inside the cell.

📐 Result 12.8 — Current and terminal voltage of a cell

A cell of emf $\varepsilon$ and internal resistance $r$ connected to an external resistance $R$ drives a current

$$I=\frac{\varepsilon}{R+r},$$

and its terminal voltage is

  • when it delivers current (discharging, current leaving the $+$ terminal): $\ V=\varepsilon-Ir=\dfrac{\varepsilon R}{R+r}\lt\varepsilon$;
  • when it is being charged (current forced into the $+$ terminal by a larger source): $\ V=\varepsilon+Ir\gt\varepsilon$;
  • on open circuit ($I=0$): $V=\varepsilon$; on short circuit ($R=0$): $V=0$ and $I_\text{sc}=\varepsilon/r$, the largest current the cell can give.

The graph of $V$ against $I$ for a cell is a straight line with intercept $\varepsilon$ on the $V$-axis, slope $-r$, and intercept $\varepsilon/r$ on the $I$-axis.

This is why headlights dim when a car's starter motor is running: the motor draws a current of a hundred amperes or more, and even a few hundredths of an ohm inside the battery then drops several volts. It also tells us how to measure $\varepsilon$ and $r$: an ideal voltmeter across the cell on open circuit reads $\varepsilon$; with a known $R$ connected it reads $V$, and then $r=\left(\dfrac{\varepsilon}{V}-1\right)R$. Two readings $(I_1,V_1)$ and $(I_2,V_2)$ give two equations $V=\varepsilon-Ir$ to solve for both.

Energy and power. The cell converts chemical energy at the rate $\varepsilon I$; of this, $I^2r$ is wasted as heat inside the cell and $VI=I^2R$ is delivered to the load, so the efficiency is $\eta=\dfrac{VI}{\varepsilon I}=\dfrac{R}{R+r}$. The power in the load,

$$P=I^2R=\frac{\varepsilon^2R}{(R+r)^2},$$

is zero both for $R=0$ (no voltage) and for $R\to\infty$ (no current), so it has a maximum in between. Setting $dP/dR=0$ gives $(R+r)^2-2R(R+r)=0$, i.e. $R=r$.

📐 Result 12.9 — Maximum power transfer

A source of emf $\varepsilon$ and internal resistance $r$ delivers the greatest power to an external resistance when $R=r$:

$$P_{\max}=\frac{\varepsilon^2}{4r},\qquad\text{with efficiency } \eta=50\%.$$

Any two load resistances $R_1$, $R_2$ that receive the same power satisfy $R_1R_2=r^2$.

✏️ Example 3 — Discharging and charging
(a) A cell of emf $1.5\ \text{V}$ and internal resistance $0.50\ \Omega$ is connected to a $2.5\ \Omega$ resistor. Find the current, the terminal voltage and the short-circuit current. (b) A $12\ \text{V}$ battery of internal resistance $0.40\ \Omega$ is being charged with a current of $5.0\ \text{A}$. Find the potential difference across its terminals, the power supplied by the charger, the rate at which energy is stored in the battery and the rate of heating inside it.
(a) $I=\dfrac{1.5}{2.5+0.50}=0.50\ \text{A}$; $\ V=\varepsilon-Ir=1.5-0.25=1.25\ \text{V}$ (check: $IR=1.25$ ✓); $\ I_\text{sc}=\dfrac{1.5}{0.50}=3.0\ \text{A}$.
(b) Charging, so $V=\varepsilon+Ir=12+5.0\times0.40=14\ \text{V}$.
Powers Charger supplies $VI=14\times5.0=70\ \text{W}$; stored as chemical energy $\varepsilon I=60\ \text{W}$; heat inside $I^2r=10\ \text{W}$. ($70=60+10$ ✓.)
Note A charger must supply more than the battery's emf, because it also has to push the current through $r$.
✏️ Example 4 — Finding $\varepsilon$ and $r$ from two readings
An ideal voltmeter across a cell reads $1.40\ \text{V}$ when the cell is connected to a $7.0\ \Omega$ resistor and $1.20\ \text{V}$ when it is connected to a $3.0\ \Omega$ resistor. (a) Find the emf and internal resistance of the cell. (b) Find the greatest power the cell can deliver to an external resistor, the resistor needed and the efficiency then. (c) Find the other load resistance that would receive the same power as the $7.0\ \Omega$ resistor.
Find the emf and internal resistance before you open the solution:
Currents $I_1=\dfrac{1.40}{7.0}=0.20\ \text{A}$, $\ I_2=\dfrac{1.20}{3.0}=0.40\ \text{A}$.
(a) $1.40=\varepsilon-0.20r$ and $1.20=\varepsilon-0.40r$. Subtracting: $0.20=0.20r$, so $r=1.0\ \Omega$ and $\varepsilon=1.40+0.20=1.6\ \text{V}$.
(b) $R=r=1.0\ \Omega$: $P_{\max}=\dfrac{\varepsilon^2}{4r}=\dfrac{2.56}{4}=0.64\ \text{W}$, at $50\%$ efficiency.
(c) $R_1R_2=r^2$: $R_2=\dfrac{1.0}{7.0}=0.14\ \Omega$. Check: $P(7)=\dfrac{2.56\times7}{64}=0.28\ \text{W}$, $P(1/7)=\dfrac{2.56/7}{(8/7)^2}=0.28\ \text{W}$ ✓.
⏱ Shortcut The slope of the $V$–$I$ line is $-r$: $r=\dfrac{1.40-1.20}{0.40-0.20}=1.0\ \Omega$, then extend the line to $I=0$ for $\varepsilon$.

In Interactive 1 set $\varepsilon=6.0\ \text{V}$ and $r=2.0\ \Omega$, and press Play to sweep the load $R$ from $0$ to $20\ \Omega$. For which load is the power in $R$ greatest, and how large is it?

At $R=2.0\ \Omega$ the readouts show $I=1.50\ \text{A}$, $V=3.00\ \text{V}$, $P=4.50\ \text{W}$ and efficiency $50\%$ — the peak of the $P$–$R$ curve, $\varepsilon^2/4r$. At $R=4.0\ \Omega$ you get $I=1.00\ \text{A}$, $V=4.00\ \text{V}$, $P=4.00\ \text{W}$ (efficiency $66.7\%$): more efficient but less power. At $R=0$ the current is the short-circuit value $3.0\ \text{A}$ but the terminal voltage, and so the load power, is zero — the $18\ \text{W}$ $(=\varepsilon I)$ is all wasted inside the cell.
Interactive 1 — A Real Cell: Terminal Voltage and Power

A cell of emf $\varepsilon$ and internal resistance $r$ drives a load $R$. The left graph is the cell's terminal voltage against current, $V=\varepsilon-Ir$; the right graph is the power delivered to the load against $R$. Move the sliders, or press Play to sweep $R$ and watch the working point move along both graphs.

6.0 V2.0 Ω4.0 Ω
current $I$—
terminal $V$—
power in $R$—
efficiency—

The potential difference across the terminals of a battery is found to be greater than its emf. This means that

Combinations of cells

One cell often cannot give the voltage or the current a job needs, so cells are grouped. Replace each cell by its ideal emf in series with its internal resistance, and the rules follow from Results 12.6–12.8.

📐 Result 12.10 — Cells in series

Cells joined $+$ to $-$ in a chain act as one cell with

$$\varepsilon_\text{eq}=\varepsilon_1+\varepsilon_2+\dots,\qquad r_\text{eq}=r_1+r_2+\dots$$

A cell connected the wrong way round (its $+$ to the $+$ of its neighbour) subtracts its emf but still adds its internal resistance. With $n$ identical cells of which $m$ are reversed, $\varepsilon_\text{eq}=(n-2m)\varepsilon$ and $r_\text{eq}=nr$. $n$ identical cells in series with a load $R$ give $I=\dfrac{n\varepsilon}{R+nr}$.

Cells in parallel. Join the positive terminals of two cells together at A and the negative terminals at B. Let $V=V_A-V_B$. The current leaving each cell's $+$ terminal is $I_1=\dfrac{\varepsilon_1-V}{r_1}$ and $I_2=\dfrac{\varepsilon_2-V}{r_2}$, and their sum is the current $I$ to the external circuit:

$$I=\frac{\varepsilon_1}{r_1}+\frac{\varepsilon_2}{r_2}-V\left(\frac1{r_1}+\frac1{r_2}\right),$$

so

$$V=\frac{\varepsilon_1r_2+\varepsilon_2r_1}{r_1+r_2}-I\,\frac{r_1r_2}{r_1+r_2}.$$

This has exactly the form $V=\varepsilon_\text{eq}-Ir_\text{eq}$ of a single cell.

📐 Result 12.11 — Cells in parallel

Two cells with like terminals joined act as one cell with

$$\varepsilon_\text{eq}=\frac{\varepsilon_1r_2+\varepsilon_2r_1}{r_1+r_2},$$ $$r_\text{eq}=\frac{r_1r_2}{r_1+r_2}.$$

For several cells: $\dfrac{\varepsilon_\text{eq}}{r_\text{eq}}=\sum\dfrac{\varepsilon_i}{r_i}$, $\ \dfrac1{r_\text{eq}}=\sum\dfrac1{r_i}$ (a cell connected the other way enters with $-\varepsilon_i$). For $n$ identical cells in parallel, $\varepsilon_\text{eq}=\varepsilon$ and $r_\text{eq}=r/n$, so $I=\dfrac{\varepsilon}{R+r/n}$: no more voltage, but more current is possible and each cell supplies only $1/n$ of it.

With unequal cells in parallel the weaker cell may be charged by the stronger one: if $V\gt\varepsilon_2$, the current $I_2=(\varepsilon_2-V)/r_2$ is negative. Even with no load at all, a current $\dfrac{\varepsilon_1-\varepsilon_2}{r_1+r_2}$ circulates between them, wasting energy — which is why cells of different emf should not be put in parallel.

Mixed grouping. $N=mn$ identical cells arranged in $m$ parallel rows, each of $n$ cells in series, form a source of emf $n\varepsilon$ and internal resistance $nr/m$, giving

$$I=\frac{n\varepsilon}{R+\dfrac{nr}{m}}=\frac{mn\varepsilon}{mR+nr}.$$

For a fixed number of cells the product $mR\cdot nr=Nr R$ is fixed, so the denominator $mR+nr$ is least when $mR=nr$: the current is greatest when the internal resistance of the battery, $nr/m$, equals the external resistance $R$ — the same condition as Result 12.9. For example, $24$ cells of $1.5\ \text{V}$ and $0.50\ \Omega$ driving $3.0\ \Omega$: $nr/m=3$ with $mn=24$ gives $n=12$, $m=2$ and $I=\dfrac{12\times1.5}{3.0+3.0}=3.0\ \text{A}$. In short: if $R\gg r$, put the cells in series; if $R\ll r$, put them in parallel.

✏️ Example 5 — A strong cell and a weak cell
A cell of emf $6.0\ \text{V}$ and internal resistance $1.0\ \Omega$ and a cell of emf $3.0\ \text{V}$ and internal resistance $1.0\ \Omega$ are connected in parallel (positive terminals together) across a $2.5\ \Omega$ resistor. (a) Find the equivalent emf and internal resistance, and the current in the resistor. (b) Find the current through each cell and say what is happening to the $3.0\ \text{V}$ cell. (c) Compare with the two cells in series across the same resistor, first aiding and then opposing each other.
(a) $\varepsilon_\text{eq}=\dfrac{6.0\times1.0+3.0\times1.0}{2.0}=4.5\ \text{V}$, $\ r_\text{eq}=0.50\ \Omega$; $\ I=\dfrac{4.5}{2.5+0.50}=1.5\ \text{A}$.
(b) Terminal voltage $V=IR=3.75\ \text{V}$. Cell 1: $I_1=\dfrac{6.0-3.75}{1.0}=2.25\ \text{A}$ out of its $+$ terminal. Cell 2: $I_2=\dfrac{3.0-3.75}{1.0}=-0.75\ \text{A}$: $0.75\ \text{A}$ flows into its $+$ terminal — it is being charged. ($2.25-0.75=1.5$ ✓.)
(c) Aiding: $I=\dfrac{9.0}{2.5+2.0}=2.0\ \text{A}$. Opposing: $I=\dfrac{3.0}{4.5}=0.67\ \text{A}$ — the internal resistances still add.
Check In (b) cell 1's terminal voltage is $6.0-2.25\times1.0=3.75\ \text{V}$ and cell 2's is $3.0+0.75\times1.0=3.75\ \text{V}$ — the same, as it must be for cells in parallel ✓.

Two identical cells, each of emf $\varepsilon$ and internal resistance $r$, are connected in parallel. Compared with one cell, the pair has

Kirchhoff's laws

Many circuits — two batteries in different branches, for instance — cannot be reduced to series and parallel combinations. Gustav Kirchhoff (1845) gave two rules that solve any network of resistors and sources carrying steady currents. They are the circuit forms of two conservation laws.

📐 Law 12.12 — Kirchhoff's laws

Junction rule (first law). At any junction of a circuit the sum of the currents entering equals the sum of the currents leaving:

$$\sum I_\text{in}=\sum I_\text{out}$$

It expresses conservation of charge: with steady currents, charge cannot pile up at a junction.

Loop rule (second law). Round any closed loop of a circuit, the algebraic sum of the changes in potential is zero:

$$\sum\Delta V=0,\quad\text{i.e.}\quad\sum\varepsilon=\sum IR$$

(each term with its sign, as below).

It expresses conservation of energy: the electrostatic field is conservative, so a charge taken round a loop and back to its start has the same potential energy as before.

Sign conventions for the loop rule. Go round the loop in a chosen direction and add the changes in potential:

🧭 Problem-solving strategy — Solving a circuit with Kirchhoff's laws
  1. Draw the circuit and mark an assumed direction and symbol for the current in every branch. The guess does not matter: a negative answer just means the current flows the other way.
  2. Use the junction rule at once to write some currents in terms of others (a circuit with $b$ branches and $j$ junctions needs $b$ unknowns and gives $j-1$ independent junction equations).
  3. Choose enough independent loops — each new loop should include at least one branch not yet used — and write the loop rule for each with consistent signs.
  4. Solve the simultaneous equations. Check with a loop you did not use, or with the power balance.
  5. Node method (often faster): put one node at $0\ \text{V}$, call the other node's potential $V$, write each branch current as $(\text{potential difference}+\text{emf})/R$ and set their sum at the node to zero — one equation for a two-node circuit.
✏️ Example 6 — Two batteries, three branches
Two nodes A (top) and B (bottom) are joined by three branches. The left branch contains a $10\ \text{V}$ battery (positive terminal towards A) in series with $R_1=2.0\ \Omega$; the right branch contains a $4.0\ \text{V}$ battery (positive terminal towards A) in series with $R_2=4.0\ \Omega$; the middle branch is a resistor $R_3=4.0\ \Omega$. The batteries have negligible internal resistance. Find the current in each branch, the potential of A relative to B, and say whether the $4.0\ \text{V}$ battery is being charged or discharged.
Find the current in the middle resistor first:
Set-up Assume $I_1$ up the left branch, $I_2$ up the right branch, $I_3$ down the middle. Junction A: $I_1+I_2=I_3$.
Loops Left loop (B → left branch → A → middle → B): $+10-2I_1-4I_3=0$. Right loop (B → right branch → A → middle → B): $+4.0-4I_2-4I_3=0$.
Solve Substitute $I_3=I_1+I_2$: $6I_1+4I_2=10$ and $4I_1+8I_2=4$. Then $I_1=2.0\ \text{A}$, $I_2=-0.50\ \text{A}$, $I_3=1.5\ \text{A}$.
Meaning $I_2$ is negative: $0.50\ \text{A}$ flows down the right branch, into the $+$ terminal of the $4.0\ \text{V}$ battery, which is being charged. $V_A-V_B=I_3R_3=6.0\ \text{V}$.
⏱ Shortcut Node method in one line: $\dfrac{10-V}{2}+\dfrac{4-V}{4}=\dfrac{V}{4}$ gives $V=6.0\ \text{V}$, then each current is read off. Check the power: $10\times2.0=20\ \text{W}$ supplied $=2.0^2\times2+0.5^2\times4+1.5^2\times4+4.0\times0.50=8+1+9+2$ ✓.

In Interactive 2 set $\varepsilon_1=6.0\ \text{V}$, $\varepsilon_2=3.0\ \text{V}$, $R_1=2.0\ \Omega$, $R_2=1.0\ \Omega$ and $R_3=2.0\ \Omega$. What current flows through the $3.0\ \text{V}$ battery?

The readouts show $V_A=3.00\ \text{V}$, $I_1=1.50\ \text{A}$, $I_2=0$ and $I_3=1.50\ \text{A}$. Node method: $V_A=\dfrac{\varepsilon_1/R_1+\varepsilon_2/R_2}{1/R_1+1/R_2+1/R_3}=\dfrac{3+3}{2}=3.0\ \text{V}$, exactly equal to $\varepsilon_2$, so there is no potential difference across $R_2$ and no current through the second battery. The left battery alone drives $6.0/(2.0+2.0)=1.5\ \text{A}$ round the outer loop through $R_1$ and $R_3$. Raise $\varepsilon_2$ above $3\ \text{V}$ and it starts to discharge; lower it and it is charged.
Interactive 2 — Kirchhoff Solver: Two Batteries, Three Branches

Two ideal batteries in the outer branches and a resistor in the middle, all between nodes A and B (B is at $0\ \text{V}$). Set the emfs and resistances; the solver applies Kirchhoff's laws and the moving dots show the direction and size of the current in every branch (faster = larger). A battery whose current enters its $+$ terminal is being charged. Press Play to start or stop the charge flow.

6.0 V3.0 V2.0 Ω1.0 Ω2.0 Ω
$I_1$ (up, left)—
$I_2$ (up, right)—
$I_3$ (down, middle)—
$V_A$—
✏️ Example 7 — NEET-style: reversed cells and a voltmeter reading
(a) Twelve identical cells, each of emf $1.5\ \text{V}$ and internal resistance $0.50\ \Omega$, are meant to be joined in series, but three of them are connected the wrong way round. The emf and internal resistance of the battery are (A) $9.0\ \text{V}$ and $6.0\ \Omega$ (B) $13.5\ \text{V}$ and $4.5\ \Omega$ (C) $9.0\ \text{V}$ and $4.5\ \Omega$ (D) $4.5\ \text{V}$ and $6.0\ \Omega$.
(b) An ideal voltmeter connected across a cell reads $2.0\ \text{V}$ on open circuit and $1.6\ \text{V}$ when a $4.0\ \Omega$ resistor is connected across the cell. The internal resistance of the cell is (A) $0.80\ \Omega$ (B) $1.0\ \Omega$ (C) $1.25\ \Omega$ (D) $0.40\ \Omega$.
(a) Emf Each reversed cell cancels one correctly connected cell and removes its own contribution: $\varepsilon_\text{eq}=(n-2m)\varepsilon=(12-6)\times1.5=9.0\ \text{V}$ (Result 12.10).
(a) Resistance Every cell, reversed or not, still adds its internal resistance: $r_\text{eq}=12\times0.50=6.0\ \Omega$.
Answer (a) (A). (B) subtracts the reversed cells only once ($9\times1.5$); (C) also drops their internal resistance.
(b) Current The open-circuit reading is the emf, $\varepsilon=2.0\ \text{V}$. With the resistor connected, $I=\dfrac{V}{R}=\dfrac{1.6}{4.0}=0.40\ \text{A}$.
(b) Lost volts $\varepsilon-V=Ir$ (Result 12.8): $r=\dfrac{2.0-1.6}{0.40}=1.0\ \Omega$.
Answer (b) (B) $1.0\ \Omega$. (A) divides the lost volts by the current the cell would give through $4\ \Omega$ alone, $2.0/4.0=0.50\ \text{A}$; (C) is just $\varepsilon/V$; (D) takes the lost volts, $0.40\ \text{V}$, as if they were the resistance.
⏱ Shortcut One line for (b): $r=R\,\dfrac{\varepsilon-V}{V}=4.0\times\dfrac{0.4}{1.6}=1.0\ \Omega$. For (a) remember "reversed: emf $-2\varepsilon$ each, resistance unchanged".
⚠️ NEET traps

1. Emf is not a force, and not always the terminal voltage. The emf is work per unit charge (volts). The terminal voltage equals it only on open circuit; it is $\varepsilon-Ir$ while the cell delivers current and $\varepsilon+Ir$ while it is being charged. On short circuit it is zero. Find the actual direction of the current in the cell first.

2. Reversed cells. In a series chain each reversed cell changes the total emf by $-2\varepsilon$ (it cancels a good cell as well as losing its own), but its internal resistance still adds: $n$ cells with $m$ reversed give $(n-2m)\varepsilon$ and $nr$.

3. Identical cells in parallel do not add their emfs. $n$ identical cells in parallel have emf $\varepsilon$ and internal resistance $r/n$. Use series when $R\gg r$, parallel when $R\ll r$.

4. Maximum power is not maximum efficiency. The load gets the most power, $\varepsilon^2/4r$, when $R=r$ — at only $50\%$ efficiency. A statement that "the efficiency is maximum when $R=r$" is false.

5. Cut, joined and bent wires. A wire of resistance $R$ cut into $n$ equal pieces joined in parallel gives $R/n^2$. Bent into a circle, it is two arcs in parallel: $R/4$ across a diameter. $n$ equal resistors give $nR$ in series and $R/n$ in parallel, so the ratio series : parallel is $n^2:1$.

6. Which conservation law? Kirchhoff's junction rule is conservation of charge; the loop rule is conservation of energy. Statement questions swap them. In the loop rule, $-IR$ across a resistor in the direction of the assumed current and $+\varepsilon$ from $-$ to $+$ through a cell; a negative answer is a direction, not an error.

You apply the loop rule to a circuit with assumed currents and find $I_2=-0.4\ \text{A}$. This means

Exercises

Connecting wires have negligible resistance, and meters are ideal unless told otherwise.

I
Resistors in series and in parallel.
  • 1 Resistors of $2\ \Omega$, $3\ \Omega$ and $5\ \Omega$ are connected in series across $20\ \text{V}$. Find the current and the voltage across the $5\ \Omega$ resistor.
  • 2 The same three resistors are connected in parallel across $20\ \text{V}$. Find the equivalent resistance and the total current.
  • 3 List all the resistances that can be made by using all three of three $4\ \Omega$ resistors.
  • 4 A wire of resistance $16\ \Omega$ is cut into four equal pieces, which are then joined in parallel. Find the resistance of the combination.
  • 5 A current of $3.0\ \text{A}$ divides between a $4\ \Omega$ and a $12\ \Omega$ resistor in parallel. Find the current in the $4\ \Omega$ resistor.
  • 6 A uniform wire of resistance $18\ \Omega$ is bent into an equilateral triangle. Find the resistance between two corners.
  • 7 Two resistors have an equivalent resistance of $9\ \Omega$ in series and $2\ \Omega$ in parallel. Find them.
  • 8 A $2\ \Omega$ resistor is in series with a parallel pair: $6\ \Omega$ in one branch and $4\ \Omega$ in series with $2\ \Omega$ in the other. The combination is connected to an ideal $10\ \text{V}$ battery. Find the current in the $4\ \Omega$ resistor.
1 $R=10\ \Omega$, $I=2.0\ \text{A}$, $V_5=10\ \text{V}$.
2 $\dfrac1R=\dfrac12+\dfrac13+\dfrac15=\dfrac{31}{30}$, $R=0.968\ \Omega$; $\ I=\dfrac{20}{0.968}=20.7\ \text{A}$.
3 All series $12\ \Omega$; all parallel $\tfrac43\ \Omega$; two in parallel plus one in series $4+2=6\ \Omega$; two in series in parallel with one $\dfrac{8\times4}{12}=\tfrac83\ \Omega$.
4 Pieces of $4\ \Omega$; four in parallel: $1.0\ \Omega$ $(=16/4^2)$.
5 $I_4=3.0\times\dfrac{12}{16}=2.25\ \text{A}$ (and $0.75\ \text{A}$ in the $12\ \Omega$).
6 Sides of $6\ \Omega$: one side in parallel with the other two, $\dfrac{6\times12}{18}=4.0\ \Omega$.
7 $R_1+R_2=9$, $\dfrac{R_1R_2}{R_1+R_2}=2$ so $R_1R_2=18$: the roots of $x^2-9x+18=0$, i.e. $3\ \Omega$ and $6\ \Omega$.
8 Branches $6\ \Omega$ and $6\ \Omega$ in parallel: $3\ \Omega$; total $5\ \Omega$, $I=2.0\ \text{A}$, which splits equally: $1.0\ \text{A}$ in the $4\ \Omega$ resistor.
II
Emf, internal resistance and power.
  • 1 A cell of emf $2.0\ \text{V}$ and internal resistance $0.50\ \Omega$ is connected to a $3.5\ \Omega$ resistor. Find the current and the terminal voltage.
  • 2 A cell reads $1.5\ \text{V}$ on open circuit and $1.2\ \text{V}$ when a $2.0\ \Omega$ resistor is connected. Find its internal resistance.
  • 3 Find the short-circuit current of a $12\ \text{V}$ battery of internal resistance $0.050\ \Omega$. Why is a short circuit dangerous?
  • 4 A $12\ \text{V}$ battery of internal resistance $0.50\ \Omega$ is charged with a current of $2.0\ \text{A}$. Find its terminal voltage.
  • 5 The $V$–$I$ graph of a cell meets the $V$-axis at $3.0\ \text{V}$ and the $I$-axis at $6.0\ \text{A}$. Find $\varepsilon$ and $r$.
  • 6 Find the maximum power a $9.0\ \text{V}$ battery of internal resistance $1.5\ \Omega$ can deliver to an external resistor.
  • 7 A cell of emf $6.0\ \text{V}$ and internal resistance $1.0\ \Omega$ has a terminal voltage of $5.0\ \text{V}$. Find the external resistance and the efficiency.
  • 8 A battery delivers the same power to a $4.0\ \Omega$ resistor as to a $9.0\ \Omega$ resistor. Find its internal resistance.
1 $I=\dfrac{2.0}{4.0}=0.50\ \text{A}$; $V=2.0-0.25=1.75\ \text{V}$.
2 $r=\left(\dfrac{\varepsilon}{V}-1\right)R=(1.25-1)\times2.0=0.50\ \Omega$.
3 $I_\text{sc}=\dfrac{12}{0.050}=240\ \text{A}$: the huge current overheats wires and the battery and can start a fire.
4 $V=\varepsilon+Ir=12+1.0=13\ \text{V}$.
5 $\varepsilon=3.0\ \text{V}$; $I_\text{sc}=\varepsilon/r$ gives $r=\dfrac{3.0}{6.0}=0.50\ \Omega$.
6 $P_{\max}=\dfrac{\varepsilon^2}{4r}=\dfrac{81}{6.0}=13.5\ \text{W}$ (with $R=1.5\ \Omega$).
7 $Ir=1.0\ \text{V}$, so $I=1.0\ \text{A}$ and $R=\dfrac{5.0}{1.0}=5.0\ \Omega$; $\eta=\dfrac{5.0}{6.0}=83\%$.
8 $\dfrac{\varepsilon^2R_1}{(R_1+r)^2}=\dfrac{\varepsilon^2R_2}{(R_2+r)^2}$ simplifies to $r^2=R_1R_2=36$, so $r=6.0\ \Omega$.
III
Combinations of cells.
  • 1 Six cells, each of emf $1.5\ \text{V}$ and internal resistance $0.25\ \Omega$, are connected in series to a $4.5\ \Omega$ resistor. Find the current.
  • 2 The same six cells are connected in parallel to the $4.5\ \Omega$ resistor. Find the current, and compare.
  • 3 Ten cells, each of emf $2.0\ \text{V}$ and internal resistance $0.50\ \Omega$, are meant to be in series, but two are connected the wrong way round. Find the current in an external $7.0\ \Omega$ resistor.
  • 4 Cells of $2.0\ \text{V}$, $0.50\ \Omega$ and $1.5\ \text{V}$, $0.25\ \Omega$ are connected in parallel. Find the emf and internal resistance of the combination.
  • 5 Twelve cells, each of emf $2.0\ \text{V}$ and internal resistance $1.0\ \Omega$, are to send the largest possible current through a $3.0\ \Omega$ resistor. How should they be grouped, and what is the current?
  • 6 Two identical cells send the same current through a resistor $R$ whether they are joined in series or in parallel. Show that $R$ equals the internal resistance of one cell.
  • 7 A $12\ \text{V}$ cell and a $6.0\ \text{V}$ cell, each of internal resistance $2.0\ \Omega$, are connected in parallel with no external load. Find the current circulating and the voltage across the terminals.
1 $\varepsilon=9.0\ \text{V}$, $r=1.5\ \Omega$: $I=\dfrac{9.0}{6.0}=1.5\ \text{A}$.
2 $\varepsilon=1.5\ \text{V}$, $r=\dfrac{0.25}{6}=0.042\ \Omega$: $I=\dfrac{1.5}{4.54}=0.33\ \text{A}$. With $R\gg r$, the series grouping is far better.
3 $\varepsilon_\text{eq}=(10-2\times2)\times2.0=12\ \text{V}$, $r=10\times0.50=5.0\ \Omega$: $I=\dfrac{12}{12}=1.0\ \text{A}$.
4 $\varepsilon=\dfrac{2.0\times0.25+1.5\times0.50}{0.75}=1.67\ \text{V}$; $\ r=\dfrac{0.50\times0.25}{0.75}=0.17\ \Omega$.
5 $mn=12$ and $\dfrac{nr}{m}=R$: $n=3m$, so $m=2$ rows of $n=6$ cells. $I=\dfrac{6\times2.0}{3.0+3.0}=2.0\ \text{A}$.
6 $\dfrac{2\varepsilon}{R+2r}=\dfrac{\varepsilon}{R+r/2}$ gives $2R+r=R+2r$, so $R=r$.
7 $I=\dfrac{12-6.0}{2.0+2.0}=1.5\ \text{A}$ round the pair; $V=12-1.5\times2.0=9.0\ \text{V}$ (also $6.0+1.5\times2.0=9.0\ \text{V}$ ✓, the $6.0\ \text{V}$ cell being charged).
IV
Kirchhoff's laws.
  • 1 At a junction, currents of $3\ \text{A}$ and $5\ \text{A}$ enter and a current of $2\ \text{A}$ leaves along a third wire. Find the current in the fourth wire and its direction.
  • 2 A single loop contains a $12\ \text{V}$ and a $3.0\ \text{V}$ battery opposing each other, each of internal resistance $0.50\ \Omega$, and resistors of $2.0\ \Omega$ and $4.0\ \Omega$. Find the current.
  • 3 Nodes A and B are joined by three branches: a $12\ \text{V}$ battery with $3.0\ \Omega$; a $6.0\ \text{V}$ battery with $6.0\ \Omega$ (both batteries with $+$ towards A, internal resistance negligible); and a $2.0\ \Omega$ resistor. Find the current in the $2.0\ \Omega$ resistor.
  • 4 In part 3 find $V_A-V_B$ and the current in each battery.
  • 5 In part 3, to what value must the $6.0\ \text{V}$ battery be changed so that no current flows through it?
  • 6 Three cells of emf $2.0\ \text{V}$, $4.0\ \text{V}$ and $6.0\ \text{V}$, each of internal resistance $1.0\ \Omega$, are connected in parallel (all $+$ terminals together) with no external load. Find the common terminal voltage and the current in each cell.
  • 7 A $6.0\ \text{V}$ battery of internal resistance $1.0\ \Omega$ is connected to $6.0\ \Omega$ and $3.0\ \Omega$ resistors in parallel. Find the current in the $3.0\ \Omega$ resistor.
  • 8 Use Kirchhoff's laws to derive the emf and internal resistance of two cells in parallel (Result 12.11).
1 $3+5=2+I$: $I=6\ \text{A}$, leaving the junction.
2 $I=\dfrac{12-3.0}{0.50+0.50+2.0+4.0}=\dfrac{9.0}{7.0}=1.29\ \text{A}$.
3 $\dfrac{12-V}{3}+\dfrac{6-V}{6}=\dfrac V2$: $24-2V+6-V=3V$, $V=5.0\ \text{V}$; $I_3=\dfrac{5.0}{2.0}=2.5\ \text{A}$.
4 $V_A-V_B=5.0\ \text{V}$; $12\ \text{V}$ battery: $\dfrac{12-5}{3}=2.33\ \text{A}$; $6.0\ \text{V}$ battery: $\dfrac{6-5}{6}=0.17\ \text{A}$, both discharging ($2.33+0.17=2.5$ ✓).
5 No current through it means $V_A=\varepsilon_2$, and then the $12\ \text{V}$ battery drives $3.0\ \Omega$ and $2.0\ \Omega$ in series: $V_A=12\times\dfrac{2.0}{5.0}=4.8\ \text{V}=\varepsilon_2$.
6 Currents out of the $+$ terminals sum to zero: $(2-V)+(4-V)+(6-V)=0$, $V=4.0\ \text{V}$. The $6\ \text{V}$ cell gives $2.0\ \text{A}$, the $4\ \text{V}$ cell none, and $2.0\ \text{A}$ flows into the $2\ \text{V}$ cell, charging it.
7 $6\parallel3=2\ \Omega$; $I=\dfrac{6.0}{3.0}=2.0\ \text{A}$; $V=4.0\ \text{V}$; $I_3=\dfrac{4.0}{3.0}=1.33\ \text{A}$.
8 With external current $I$ and terminal voltage $V$: loop rule in each cell gives $I_k=(\varepsilon_k-V)/r_k$; the junction rule $I_1+I_2=I$ then gives $V=\dfrac{\varepsilon_1r_2+\varepsilon_2r_1}{r_1+r_2}-I\dfrac{r_1r_2}{r_1+r_2}$, which is $V=\varepsilon_\text{eq}-Ir_\text{eq}$.
🎯 Exam corner NEET · MCQ

E1. NEET · MCQ Statement I: Kirchhoff's junction rule follows from the conservation of electric charge. Statement II: Kirchhoff's loop rule follows from the conservation of linear momentum of the charge carriers. In the light of these statements, choose the correct option. (A) Both Statement I and Statement II are correct (B) Both Statement I and Statement II are incorrect (C) Statement I is correct but Statement II is incorrect (D) Statement I is incorrect but Statement II is correct

Statement I With steady currents no charge can pile up at a junction, so what flows in must flow out (Law 12.12). Correct.
Statement II The loop rule says the potential changes round a closed loop add to zero: a charge taken round the loop returns with the same potential energy. That is conservation of energy, not of momentum. Incorrect.
Answer (C).
⏱ Shortcut Junction — charge; loop — energy. Anything else in either statement makes it false.

E2. NEET · MCQ A cell drives a current of $1.0\ \text{A}$ through a $2.0\ \Omega$ resistor and a current of $0.50\ \text{A}$ through a $5.0\ \Omega$ resistor. The emf and internal resistance of the cell are (A) $2.5\ \text{V}$, $0.50\ \Omega$ (B) $3.0\ \text{V}$, $0.50\ \Omega$ (C) $4.0\ \text{V}$, $2.0\ \Omega$ (D) $3.0\ \text{V}$, $1.0\ \Omega$

Equations $\varepsilon=I(R+r)$ (Result 12.8): $\varepsilon=1.0\,(2.0+r)$ and $\varepsilon=0.50\,(5.0+r)$.
Solve $2.0+r=2.5+0.50r$, so $0.50r=0.50$: $r=1.0\ \Omega$ and $\varepsilon=3.0\ \text{V}$.
Answer (D).
⏱ Shortcut Test the options in the first condition, $\varepsilon/(2+r)=1$: only (A), (C) and (D) pass. Then the second, $\varepsilon/(5+r)=0.5$: only (D) passes.

E3. NEET · MCQ Assertion (A): While a storage battery is being charged, the potential difference across its terminals is greater than its emf. Reason (R): During charging, the current flows through the battery from its positive terminal to its negative terminal, so the potential drop across its internal resistance adds to the emf. Choose the correct option. (A) Both A and R are true and R is the correct explanation of A (B) Both A and R are true but R is not the correct explanation of A (C) A is true but R is false (D) A is false but R is true

Reason The charger forces current into the $+$ terminal, so inside the battery it flows from $+$ to $-$. The terminal voltage must provide both the emf and the drop $Ir$: true.
Assertion That is $V=\varepsilon+Ir\gt\varepsilon$ (Result 12.8): true, and it follows directly from R.
Answer (A).
⏱ Shortcut Discharging: current leaves $+$, $V=\varepsilon-Ir$. Charging: current enters $+$, $V=\varepsilon+Ir$.

E4. NEET · MCQ Three identical resistors, each of resistance $R$, are connected in four different ways. Match each arrangement in List-I with its equivalent resistance in List-II.
List-I: (a) all three in series (b) all three in parallel (c) two in parallel, and the pair in series with the third (d) two in series, and the pair in parallel with the third
List-II: (i) $\tfrac23R$ (ii) $3R$ (iii) $\tfrac13R$ (iv) $\tfrac32R$
Choose the correct answer: (A) a-ii, b-iii, c-i, d-iv (B) a-iii, b-ii, c-iv, d-i (C) a-ii, b-i, c-iv, d-iii (D) a-ii, b-iii, c-iv, d-i

Match (a) $3R$ (Result 12.6): ii. (b) $R/3$ (Result 12.7): iii. (c) $\dfrac R2+R=\dfrac32R$: iv. (d) $\dfrac{2R\times R}{2R+R}=\dfrac23R$: i.
Answer (D) a-ii, b-iii, c-iv, d-i.
⏱ Shortcut The largest value goes with all-series and the smallest with all-parallel: a-ii and b-iii leave only (A) and (D). Then "two in parallel plus one" must exceed $R$, so c-iv: (D).

E5. NEET · MCQ The graph shows how the terminal voltage $V$ of a cell changes with the current $I$ it delivers. The emf of the cell, its internal resistance, and the greatest power it can deliver to an external resistor are, respectively, (A) $6\ \text{V}$, $2\ \Omega$, $4.5\ \text{W}$ (B) $6\ \text{V}$, $0.5\ \Omega$, $18\ \text{W}$ (C) $3\ \text{V}$, $2\ \Omega$, $1.125\ \text{W}$ (D) $6\ \text{V}$, $2\ \Omega$, $18\ \text{W}$
123246I (A)V (V)0

Read the graph $V=\varepsilon-Ir$ (Result 12.8): the intercept on the $V$-axis is $\varepsilon=6\ \text{V}$, and the intercept on the $I$-axis is the short-circuit current $\varepsilon/r=3\ \text{A}$, so $r=2\ \Omega$ (the magnitude of the slope).
Maximum power At $R=r$: $P_{\max}=\dfrac{\varepsilon^2}{4r}=\dfrac{36}{8}=4.5\ \text{W}$ (Result 12.9).
Answer (A).
⏱ Shortcut $18\ \text{W}$ is $\varepsilon I_\text{sc}$, the rate at which the shorted cell turns chemical energy into heat inside itself — the load then gets nothing. The maximum load power is always a quarter of $\varepsilon I_\text{sc}$.

E6. NEET · MCQ How many of the following statements are correct?
(i) The emf of $n$ identical cells connected in parallel is equal to the emf of one cell.
(ii) $n$ identical resistors of resistance $R$ connected in parallel have an equivalent resistance $R/n$.
(iii) A cell delivers power to an external resistor with $100\%$ efficiency when the external resistance equals its internal resistance.
(iv) The internal resistance of a cell increases as the cell ages.
(v) The potential difference across the terminals of a short-circuited cell equals its emf.
(A) Two (B) Three (C) Four (D) Five

Check each (i) ✓ (Result 12.11). (ii) ✓ (Result 12.7). (iii) ✗ — at $R=r$ the power is greatest but the efficiency $R/(R+r)$ is only $50\%$. (iv) ✓ (Definition 12.11). (v) ✗ — on short circuit $V=\varepsilon-I_\text{sc}r=0$.
Answer (B) three statements: (i), (ii) and (iv).
⏱ Shortcut Open circuit: $V=\varepsilon$. Short circuit: $V=0$. Matched load: half of $\varepsilon$ across the load, half lost inside.
🔬 Research–Teaching NexusResearch-tutored · optional, about 45 minutes

Research question. How does the internal resistance of an AA cell change as it is used up, and how does that limit what the cell can power?

Why it matters. Battery engineers for phones, electric vehicles and medical implants track internal resistance as a key sign of a cell's health: as a battery ages its $r$ rises, its terminal voltage sags under load (Result 12.8) and it can no longer deliver high power, even when it still holds charge. Grid-scale storage, drones and pacemakers are all designed around this. The measurement needs only a cell, a resistor and a voltmeter.

What to do.

  1. Measure the open-circuit voltage $\varepsilon$ of a fresh AA cell with a digital voltmeter.
  2. Connect a known resistor (about $4$–$10\ \Omega$) across it for a few seconds and read the terminal voltage $V$. Compute $r=(\varepsilon/V-1)R$.
  3. Repeat with two or three other resistors and plot $V$ against $I=V/R$; the slope gives $r$ and the intercept $\varepsilon$.
  4. Discharge the cell through a small lamp or resistor, stopping every 30 minutes to repeat steps 1–3, until the lamp is dim.
  5. Plot $\varepsilon$ and $r$ against time of use, and calculate $\varepsilon^2/4r$, the largest power the cell could deliver, at each stage.

Tools: AA cells (fresh and used), digital multimeter, resistors of a few ohms, a small lamp or a $10\ \Omega$ resistor for discharging, a clock, a spreadsheet.

Hand in: Your tables, the $V$–$I$ graphs at the start and the end, the graphs of $\varepsilon$ and $r$ against time, and a paragraph explaining why a "flat" cell may still show nearly $1.5\ \text{V}$ on an open-circuit voltmeter.

Going further. Compare an alkaline cell with a zinc–carbon cell, or with a rechargeable NiMH cell of the same size. Which keeps a low internal resistance longest, and which would you choose for a high-current device such as a camera flash?

Instructor note: fresh alkaline AA cells typically show $r\approx0.1$–$0.3\ \Omega$, rising several-fold as they discharge, while $\varepsilon$ falls only slowly at first. Keep each load connection brief so the cell does not warm up or recover during the reading. A common surprise is that a used cell's open-circuit voltage looks healthy — the point of the exercise.

🧪 Self-check quiz

0/5 correct

Q1. Three identical resistors connected in series have an equivalent resistance of $9\ \Omega$. Connected in parallel, their equivalent resistance is

Q2. A uniform wire of resistance $16\ \Omega$ is bent into a circle. The resistance between two diametrically opposite points of the circle is

Q3. A $12\ \text{V}$ battery of internal resistance $0.50\ \Omega$ is being charged with a current of $2.0\ \text{A}$. The potential difference across its terminals is

Q4. Kirchhoff's loop rule, $\sum\Delta V=0$ round any closed loop, is a statement of the conservation of

Q5. A battery of emf $10\ \text{V}$ and internal resistance $2.0\ \Omega$ is connected to a variable external resistor. The greatest power that can be delivered to the resistor is