Chapter 12 · Introduction

Chapter 12 — Current Electricity

Charges in motion. Electrons drifting slowly through a metal give the current, Ohm's law and resistance; a cell with an emf and an internal resistance drives it; and Kirchhoff's two rules, the Wheatstone bridge and the metre bridge let you solve and measure any circuit.

Flip a switch and the room lights up at once — yet the electrons in the copper wire crawl along at a fraction of a millimetre per second, slower than an ant. Start a car on a cold morning and the headlights dim while the starter motor turns, because the battery's own internal resistance eats part of its voltage when it delivers a large current. An electric heater glows red while the cable feeding it stays cool, though both carry the same current. A fuse melts, an LED refuses to light when connected the wrong way round, and a laboratory metre bridge measures an unknown resistance to a fraction of a percent using nothing but a wire, a jockey and a galvanometer that reads zero. All of this is current electricity, and every part of it can be calculated.

The chapter begins inside the conductor: a current $I=\dfrac{dq}{dt}$ is carried by free electrons with a small drift velocity, $I=neAv_d$, and from their collisions come Ohm's law $V=IR$, the resistivity in $R=\dfrac{\rho L}{A}$, its change with temperature, and the heating $P=I^2R$. Then come real circuits: resistors in series and parallel, the emf $\varepsilon$ and internal resistance $r$ of a cell, terminal voltage $V=\varepsilon-Ir$, combinations of cells, and Kirchhoff's laws — the junction rule (charge is conserved) and the loop rule (energy is conserved) — that solve any network. Finally the Wheatstone bridge and its laboratory form, the metre bridge, which measure resistance by finding a null. Current electricity is one of the most heavily tested units of JEE Main, and a favourite of the numerical-answer section.

$I=\tfrac{dq}{dt}$→Drift velocity, $I=neAv_d$→Ohm's law $V=IR$→$R=\tfrac{\rho L}{A}$→$R_T=R_0[1+\alpha\Delta T]$→$P=I^2R$→Series & parallel→emf & internal resistance→Kirchhoff's laws→Wheatstone & metre bridge
🎯 By the end of this chapter you can…
  • define current and current density, and use $I=neAv_d$, relaxation time and mobility $\mu=\dfrac{v_d}{E}$ to explain conduction in a metal;
  • state Ohm's law and its conditions, use $R=\dfrac{\rho L}{A}$ (including wires that are stretched or reshaped), and tell ohmic from non-ohmic conductors by their V–I graphs;
  • use $R_T=R_0\left[1+\alpha(T-T_0)\right]$ and calculate electrical energy and power, $P=VI=I^2R=\dfrac{V^2}{R}$;
  • reduce series–parallel networks, and use potential and current dividers;
  • use emf, internal resistance and $V=\varepsilon-Ir$ (discharging) or $V=\varepsilon+Ir$ (charging), and find the condition and value of maximum power transfer;
  • combine cells in series and in parallel, and choose the arrangement of cells that gives the largest current;
  • apply Kirchhoff's junction and loop rules with consistent sign conventions to solve multi-loop circuits;
  • use the balance condition $\dfrac PQ=\dfrac RS$ of the Wheatstone bridge, symmetry shortcuts, and the metre-bridge formula $X=R\,\dfrac{100-l}{l}$ with end errors;
  • solve JEE Main MCQ and numerical-answer problems on current electricity.

A cell of emf $12\ \text{V}$ and internal resistance $1\ \Omega$ drives a current through $R_1=3\ \Omega$ and $R_2=2\ \Omega$ in series. What is the potential difference across the terminals of the cell?

Set $R_2=2\ \Omega$. The current is $I=\dfrac{\varepsilon}{R_1+R_2+r}=\dfrac{12}{6}$, so the readout shows $I=2.00\ \text{A}$, and the cell loses $Ir=2\ \text{V}$ inside itself: the terminal voltage reads $10.00\ \text{V}$ (Section 12.2). In the graph, the potential climbs $12\ \text{V}$ through the emf, slips $2\ \text{V}$ across $r$, then falls $6\ \text{V}$ across $R_1$ and $4\ \text{V}$ across $R_2$ — back to where it started, which is Kirchhoff's loop rule. The power in $R_2$ is $8.00\ \text{W}$. Now try $R_2=8\ \Omega$: $I=1\ \text{A}$, terminal voltage $11\ \text{V}$, and the power in $R_2$ is again $8\ \text{W}$, because $2\times8=(r+R_1)^2$.
Teaser — Where Does the Voltage Go?

A cell of emf $\varepsilon=12\ \text{V}$ and internal resistance $r=1\ \Omega$ drives a current round a loop through $R_1=3\ \Omega$ and a variable resistor $R_2$ (connecting wires have no resistance). The dots show the direction of the conventional current, moving faster when $I$ is larger. The graph is the potential at each point, going once round the loop from the negative terminal. Choose $R_2$ and press Play.

8 Ω
current $I=\tfrac{\varepsilon}{R_1+R_2+r}$—
terminal voltage $\varepsilon-Ir$—
power in $R_2$—

Sections in this chapter

🎯 Chapter mixed test JEE Main · MCQJEE Main · Numerical

Eight problems drawn from all three sections and shuffled, as in the real paper; several need two sections at once. Answer each one and press Submit (NTA marking: $+4$ correct, $-1$ wrong, $0$ unanswered), or press ⏱ Take as a timed test for the real-exam experience: $8$ questions at the JEE Main pace of $2.4$ minutes each, with the NTA question palette. Draw the circuit before you calculate.

E1. JEE Main · MCQ Two wires of the same metal, with lengths in the ratio $1:2$ and radii in the ratio $2:1$, are connected in series to a battery. The ratio $v_1:v_2$ of the drift speeds of the free electrons in them is (A) $1:2$ (B) $4:1$ (C) $1:4$ (D) $1:1$

Same current In series the same current $I$ flows through both wires, and $I=neAv_d$ with the same $n$ (Result 12.1), so $v_d\propto\dfrac1A\propto\dfrac{1}{r^2}$.
Ratio $\dfrac{v_1}{v_2}=\dfrac{r_2^2}{r_1^2}=\dfrac{1}{4}$ — the lengths do not matter.
Answer (C) $1:4$.
⏱ Shortcut Electrons drift faster where the wire is thinner. (B) inverts the ratio; (A) wrongly uses the lengths.

E2. JEE Main · Numerical Resistors of $4\ \Omega$ and $12\ \Omega$ are connected in parallel, and the pair is connected in series with a $2\ \Omega$ resistor across a battery of emf $24\ \text{V}$ and internal resistance $1\ \Omega$. Find the power dissipated in the $4\ \Omega$ resistor, in watts. Give the answer to the nearest integer.

Reduce $4\parallel12=\dfrac{4\times12}{16}=3\ \Omega$ (Result 12.7); total resistance $3+2+1=6\ \Omega$, so $I=\dfrac{24}{6}=4\ \text{A}$ (Result 12.8).
Current divider $I_4=\dfrac{12}{16}\times4=3\ \text{A}$; $P=I_4^2R=9\times4$ (Law 12.5).
Answer $36\ \text{W}$, i.e. $36$.
⏱ Shortcut The voltage across the pair is $4\times3=12\ \text{V}$, so $P_4=\dfrac{V^2}{R}=\dfrac{144}{4}$. Forgetting the internal resistance gives $I=4.8\ \text{A}$ and $51.8\ \text{W}$.

E3. JEE Main · MCQ A wire $50\ \text{cm}$ long with a cross-section of $1.0\ \text{mm}^2$ is placed in the right gap of a metre bridge, and a $4\ \Omega$ resistor in the left gap. The null point is $40\ \text{cm}$ from the left end. The resistivity of the material of the wire is (A) $1.2\times10^{-5}\ \Omega\,\text{m}$ (B) $5.3\times10^{-6}\ \Omega\,\text{m}$ (C) $3.0\times10^{-6}\ \Omega\,\text{m}$ (D) $1.2\times10^{-7}\ \Omega\,\text{m}$

Metre bridge $X=R\,\dfrac{100-l}{l}=4\times\dfrac{60}{40}=6\ \Omega$ (Law 12.16).
Resistivity $\rho=\dfrac{XA}{L}=\dfrac{6\times1.0\times10^{-6}}{0.50}=1.2\times10^{-5}\ \Omega\,\text{m}$ (Definition 12.6).
Answer (A).
⏱ Shortcut The null point is nearer the left end, so the left gap holds the smaller resistance: $X\gt4\ \Omega$. (B) comes from the inverted ratio, $X=\tfrac83\ \Omega$; (D) forgets that $1\ \text{mm}^2=10^{-6}\ \text{m}^2$.

E4. JEE Main · Numerical A heater coil has a resistance of $100\ \Omega$ at $20^\circ\text{C}$, and the temperature coefficient of resistance of its wire is $4.0\times10^{-4}\ \text{K}^{-1}$. Find the power it draws from a $240\ \text{V}$ supply when it is working at $520^\circ\text{C}$, in watts. Give the answer to the nearest integer.

Hot resistance $R=R_0\left[1+\alpha(T-T_0)\right]=100\,(1+4.0\times10^{-4}\times500)=120\ \Omega$ (Result 12.4).
Power $P=\dfrac{V^2}{R}=\dfrac{240^2}{120}$ (Law 12.5).
Answer $480\ \text{W}$, i.e. $480$.
⏱ Shortcut Using the cold resistance gives $576\ \text{W}$ — the switch-on surge, not the working power. A metal's resistance rises as it heats, so its power falls.

E5. JEE Main · MCQ A battery of emf $10\ \text{V}$ and internal resistance $0.5\ \Omega$ is being charged with a current of $2\ \text{A}$. The potential difference across its terminals is (A) $9\ \text{V}$ (B) $11\ \text{V}$ (C) $10\ \text{V}$ (D) $12\ \text{V}$

Direction While charging, the current is driven into the positive terminal, against the emf, so the charger must supply the emf plus the drop across $r$ (Result 12.8).
Numbers $V=\varepsilon+Ir=10+2\times0.5$.
Answer (B) $11\ \text{V}$.
⏱ Shortcut Discharging: $V\lt\varepsilon$; charging: $V\gt\varepsilon$. (A) is the discharging value.

E6. JEE Main · Numerical In a bridge network $ABCD$, $AB=3\ \Omega$, $BC=6\ \Omega$, $AD=6\ \Omega$, $DC=12\ \Omega$, and a galvanometer of resistance $50\ \Omega$ is connected between $B$ and $D$. A cell of emf $13\ \text{V}$ and internal resistance $0.5\ \Omega$ is connected across $A$ and $C$. Find the total power dissipated in the bridge network, in watts. Give the answer to the nearest integer.

Balanced? $\dfrac{AB}{BC}=\dfrac36=\dfrac12$ and $\dfrac{AD}{DC}=\dfrac{6}{12}=\dfrac12$: the bridge is balanced (Section 12.3), no current flows through the galvanometer, and its $50\ \Omega$ does not matter.
Reduce Two branches $3+6=9\ \Omega$ and $6+12=18\ \Omega$ in parallel: $\dfrac{9\times18}{27}=6\ \Omega$. Then $I=\dfrac{13}{6+0.5}=2\ \text{A}$ (Result 12.8).
Answer $P=I^2R=4\times6=24\ \text{W}$, i.e. $24$.
⏱ Shortcut Always test $PS=QR$ first ($3\times12=6\times6$): a balanced bridge's middle arm can simply be deleted.

E7. JEE Main · MCQ The potential difference across a metal wire is doubled while its temperature is kept constant. Which statement is correct? (A) The relaxation time doubles (B) The number density of free electrons doubles (C) The mobility of the electrons doubles (D) The drift speed doubles, while the resistance is unchanged

Field Doubling $V$ doubles the field $E=V/L$ inside the wire. At a fixed temperature $\tau$, $n$ and $\mu=\dfrac{e\tau}{m}$ are properties of the metal and do not change (Definitions 12.3, 12.4).
Drift $v_d=\mu E$ doubles, so $I=neAv_d$ doubles and $R=\dfrac VI$ stays the same — Ohm's law (Law 12.3).
Answer (D).
⏱ Shortcut Only a change of temperature (or material) changes $\tau$, $\mu$ and $\rho$; a change of voltage changes only $E$, $v_d$ and $I$.

E8. JEE Main · Numerical A cell of emf $12\ \text{V}$ and internal resistance $2\ \Omega$ and a cell of emf $6\ \text{V}$ and internal resistance $1\ \Omega$ are connected in parallel, positive terminal to positive terminal, across a $2\ \Omega$ resistor. Find the power dissipated in the $2\ \Omega$ resistor, in watts. Give the answer to the nearest integer.

Kirchhoff Let $V$ be the potential of the common positive line (negative line at $0$). Kirchhoff's junction rule (Section 12.2): $\dfrac{12-V}{2}+\dfrac{6-V}{1}=\dfrac{V}{2}$, so $12=2V$ and $V=6\ \text{V}$.
Power Current in the resistor $\dfrac62=3\ \text{A}$; $P=\dfrac{V^2}{R}=\dfrac{36}{2}$.
Answer $18\ \text{W}$, i.e. $18$.
⏱ Shortcut Equivalent cell (Result 12.11): $\varepsilon_\text{eq}=\dfrac{12\times1+6\times2}{3}=8\ \text{V}$, $r_\text{eq}=\tfrac23\ \Omega$, $I=\dfrac{8}{2+\frac23}=3\ \text{A}$. Notice that the $6\ \text{V}$ cell carries no current at all: the terminal voltage equals its emf.
✅ Before you start
This chapter is built on Chapter 11: charge and its conservation (Section 11.1), the electric field that pushes the electrons, and potential difference as work per unit charge, $V=\dfrac{W}{q}$ (Section 11.3). Drift velocity uses $\mathbf F=m\mathbf a$ for an electron in a field (Section 3.1), power is the rate of doing work (Section 4.2), and the temperature coefficient of resistance is handled like thermal expansion (Section 7.5). The metre bridge is also a laboratory experiment, so keep the error analysis of Section 1.3 handy. From mathematics: solving two or three simultaneous linear equations, and ratio and proportion.