Chapter 14 · Electromagnetic Induction and Alternating Currents

14.3 Alternating Current Circuits, Resonance and Transformers

A voltage that swings back and forth fifty times a second: how a rotating coil makes it, why we quote its rms value, how resistors, inductors and capacitors oppose it, why a series LCR circuit resonates at $\omega_0=1/\sqrt{LC}$, why the average power is $V_\text{rms}I_\text{rms}\cos\phi$, and how a transformer trades voltage for current.

The socket in an Indian home does not supply a steady voltage. Its voltage rises to about $325\ \text{V}$, falls through zero, swings to $-325\ \text{V}$ and back again fifty times every second. Yet the label on the meter, the heater and the phone charger all say "$230\ \text{V}$". Why that number? And why did the whole world settle on this back-and-forth alternating current (AC) rather than the steady direct current (DC) of a battery? The short answer is the transformer: with AC, a pair of coils on an iron core can raise the voltage to hundreds of kilovolts for transmission across a country — cutting the heating losses in the wires enormously — and lower it again to a safe value at your door. Nothing so simple works for DC.

AC also brings new physics. An inductor or a capacitor, which in a steady DC circuit is just a short circuit or a gap, now opposes the current in a way that depends on frequency, and pushes the current out of step with the voltage. Combine a resistor, an inductor and a capacitor in series and the circuit picks out one frequency at which the current is largest — resonance, the principle by which a radio selects one station out of hundreds. In this section we make AC with a rotating coil, define the rms value, treat $R$, $L$ and $C$ with rotating arrows called phasors, solve the series LCR circuit, find the power it takes and finish with the transformer. We use Faraday's law and self-inductance from § 14.1 and § 14.2, and the capacitor from Chapter 11.

Alternating voltage, the AC generator and rms values

The simplest alternating voltage is a sine function of time. Every steady AC source in this section — mains supply, a signal generator, a rotating generator — gives one.

📘 Definition 14.6 — Alternating voltage and current

A (sinusoidal) alternating voltage is one that varies with time as

$$v=v_m\sin\omega t,$$

and an alternating current varies as $i=i_m\sin(\omega t-\phi)$. Here $v_m$ and $i_m$ are the peak values (amplitudes), $\omega$ is the angular frequency in $\text{rad/s}$, $\nu=\omega/2\pi$ the frequency in hertz, $T=1/\nu$ the period, and $\phi$ the phase difference between the voltage and the current. Indian mains has $\nu=50\ \text{Hz}$, so $\omega=100\pi\ \text{rad/s}\approx314\ \text{rad/s}$ and $T=20\ \text{ms}$.

Making AC: the AC generator. A coil of $N$ turns, each of area $A$, is turned at a steady angular speed $\omega$ in a uniform magnetic field $\mathbf B$, about an axis in its plane and perpendicular to $\mathbf B$. Let $\theta=\omega t$ be the angle between the normal to the coil and $\mathbf B$. The flux linkage is $N\Phi_B=NBA\cos\omega t$, and Faraday's law (§ 14.1) gives the induced emf

$$\varepsilon=-\frac{d(N\Phi_B)}{dt}=NBA\omega\sin\omega t .$$

The ends of the coil are joined to two slip rings that turn with it; fixed carbon brushes pressing on the rings take the alternating emf out to the circuit. The mechanical work needed to turn the coil (against the magnetic force on the induced current, by Lenz's law) comes from a turbine driven by steam, falling water or wind.

📐 Result 14.11 — Emf of an AC generator

A coil of $N$ turns and area $A$ rotating at constant angular speed $\omega$ about an axis perpendicular to a uniform field $B$ produces

$$\varepsilon=\varepsilon_0\sin\omega t,\qquad \varepsilon_0=NBA\omega .$$

The emf is largest when the plane of the coil is parallel to $\mathbf B$ (flux zero but changing fastest) and zero when the plane is perpendicular to $\mathbf B$ (flux largest but momentarily not changing). The frequency of the AC equals the number of revolutions per second; doubling the speed doubles both $\varepsilon_0$ and the frequency.

Which value do we quote? The average of a sine over a whole cycle is zero, so the ordinary average is useless for AC. What matters for heating is $i^2$: a resistor $R$ dissipates power $i^2R$ whichever way the current flows. So we define the steady current that would give the same average heating.

📘 Definition 14.7 — Root-mean-square (rms) value

The rms value of a periodic current is the square root of the mean of $i^2$ over one period:

$$I_\text{rms}=\sqrt{\langle i^2\rangle}.$$

Equivalently, it is the value of the steady (DC) current that produces the same average power in a resistor. The rms voltage is defined in the same way. AC ammeters and voltmeters are calibrated to read rms values, and ratings such as "$230\ \text{V}$ mains" or "$5\ \text{A}$ socket" are rms values.

For a sine, $i^2=i_m^2\sin^2\omega t$. Over a whole cycle $\sin^2\omega t$ and $\cos^2\omega t$ have the same average (one is the other shifted by a quarter period), and they add up to $1$ at every instant, so each averages to $\tfrac12$. Hence $\langle i^2\rangle=i_m^2/2$.

📐 Result 14.12 — Rms and mean values of a sinusoidal quantity

For $i=i_m\sin\omega t$ (and likewise for a sinusoidal voltage):

$$I_\text{rms}=\frac{i_m}{\sqrt2}\approx0.707\,i_m,\qquad V_\text{rms}=\frac{v_m}{\sqrt2}.$$

The mean over a full cycle is $0$; the mean over a half cycle (one positive loop) is $\dfrac{2i_m}{\pi}\approx0.637\,i_m$, from the area $\displaystyle\int_0^{\pi}\sin x\,dx=2$ under one loop. These results hold only for sine waves: for any other waveform go back to the definition and average $i^2$.

So $230\ \text{V}$ mains has a peak of $230\sqrt2=325\ \text{V}$ and swings through about $650\ \text{V}$ from crest to trough — the insulation of every appliance must withstand the peak, not the rms value. For waveforms that are not sine waves, the definition gives, for example: a square wave switching between $+I_0$ and $-I_0$ has $I_\text{rms}=I_0$ (since $i^2=I_0^2$ always); a half-wave rectified sine (one loop on, one loop off) has $I_\text{rms}=i_m/2$; and a current $i=I_1+i_m\sin\omega t$ (a steady part plus a sine) has $I_\text{rms}=\sqrt{I_1^2+i_m^2/2}$, because the cross term $2I_1i_m\sin\omega t$ averages to zero.

✏️ Example 1 — A small AC generator
A rectangular coil of $50$ turns, each $8.0\ \text{cm}\times10\ \text{cm}$, rotates at $3000$ revolutions per minute about an axis perpendicular to a uniform field of $0.40\ \text{T}$. (a) Find the peak emf and the rms emf. (b) Find the emf at the instant the plane of the coil makes $30^\circ$ with the field. (c) The generator (of negligible resistance) is connected to a $20\ \Omega$ resistor. Find the average power delivered.
(a) $A=0.080\times0.10=8.0\times10^{-3}\ \text{m}^2$; $3000\ \text{rpm}=50\ \text{rev/s}$, so $\omega=2\pi\times50=100\pi\ \text{rad/s}$. $\varepsilon_0=NBA\omega=50\times0.40\times8.0\times10^{-3}\times100\pi=50.3\ \text{V}$; $\varepsilon_\text{rms}=50.3/\sqrt2=35.5\ \text{V}$.
(b) The plane at $30^\circ$ to $\mathbf B$ means the normal is at $60^\circ$ to $\mathbf B$, so $\omega t=60^\circ$: $\varepsilon=50.3\sin60^\circ=43.5\ \text{V}$.
(c) $P=\dfrac{\varepsilon_\text{rms}^2}{R}=\dfrac{\varepsilon_0^2}{2R}=\dfrac{(50.3)^2}{40}=63.2\ \text{W}$.
Check With the plane parallel to $\mathbf B$ the formula gives $\varepsilon_0\sin90^\circ=\varepsilon_0$, the maximum — as it should: the sides of the coil then cut the field lines head-on.
✏️ Example 2 — Rms values of four waveforms
Find the rms value of each current: (a) $i=4\sin\omega t+3\cos\omega t$ (in amperes); (b) a half-wave rectified sine of peak $4.0\ \text{A}$ — and also its mean value over a full cycle; (c) a current of $6.0\ \text{A}$ that flows for one-third of each period and is zero for the rest; (d) $i=3+4\sin\omega t$ (in amperes).
(a) Two sinusoids of the same frequency, a quarter period apart, add to one sinusoid of amplitude $\sqrt{4^2+3^2}=5\ \text{A}$. So $I_\text{rms}=5/\sqrt2=3.54\ \text{A}$.
(b) $i^2$ is $i_m^2\sin^2\omega t$ for half the period and $0$ for the other half, so $\langle i^2\rangle=\tfrac12\cdot\tfrac12i_m^2$ and $I_\text{rms}=i_m/2=2.0\ \text{A}$. Mean: one loop of average $2i_m/\pi$ for half the time, so $\langle i\rangle=i_m/\pi=1.27\ \text{A}$.
(c) $\langle i^2\rangle=\tfrac13\times36=12\ \text{A}^2$, so $I_\text{rms}=\sqrt{12}=3.46\ \text{A}$.
(d) $\langle i^2\rangle=9+\tfrac{16}{2}+\langle24\sin\omega t\rangle=9+8+0=17\ \text{A}^2$; $I_\text{rms}=\sqrt{17}=4.12\ \text{A}$ — not $3+4/\sqrt2$.
⏱ Shortcut Only for a pure sine is $I_\text{rms}=i_m/\sqrt2$. For anything else write down $i^2$, average it over one period, take the root.

An AC voltmeter connected across the mains reads $230\ \text{V}$. Which statement is correct?

Resistor, inductor and capacitor on AC: phasors and reactance

Connect a single element to an AC source $v=v_m\sin\omega t$. What current flows, and is it in step with the voltage? A picture makes the answers easy to remember and to combine.

📘 Definition 14.8 — Phasor

A phasor is an arrow from the origin whose length equals the peak value of a sinusoidal quantity and which rotates anticlockwise with angular velocity $\omega$. At time $t$ it makes angle $\omega t+\alpha$ with the $x$-axis, and its projection on the $y$-axis, $v_m\sin(\omega t+\alpha)$, is the instantaneous value. Quantities of the same frequency keep fixed angles between their phasors, so the phase difference is the angle between the arrows; and adding the quantities is the same as adding their phasors as vectors.

Resistor. Ohm's law holds at every instant: $i=v/R=(v_m/R)\sin\omega t$. The current is in phase with the voltage, with $i_m=v_m/R$; the two phasors lie along the same line.

Inductor (pure, no resistance). The source voltage must equal the back-emf: $v=L\,\dfrac{di}{dt}$ (§ 14.2). Integrating $\dfrac{di}{dt}=\dfrac{v_m}{L}\sin\omega t$ gives

$$i=-\frac{v_m}{\omega L}\cos\omega t=\frac{v_m}{\omega L}\sin\!\left(\omega t-\frac{\pi}{2}\right).$$

The current lags the voltage by $\pi/2$ (a quarter cycle): the voltage is largest when the current is changing fastest, which is when the current passes through zero. The peak current is $i_m=v_m/X_L$ with $X_L=\omega L$.

Capacitor. The charge follows the voltage, $q=Cv=Cv_m\sin\omega t$, and the current is its rate of change:

$$i=\frac{dq}{dt}=\omega Cv_m\cos\omega t=\frac{v_m}{1/\omega C}\sin\!\left(\omega t+\frac{\pi}{2}\right).$$

The current leads the voltage by $\pi/2$: the capacitor charges fastest as the voltage passes through zero, and the current stops just as the voltage reaches its peak. The peak current is $i_m=v_m/X_C$ with $X_C=1/\omega C$.

📘 Definition 14.9 — Reactance

The reactance of an element is the ratio of the peak (or rms) voltage across it to the peak (or rms) current through it when the voltage and current are $90^\circ$ out of phase. Its SI unit is the ohm.

  • Inductive reactance $\ X_L=\omega L=2\pi\nu L$ — grows with frequency; for DC ($\nu=0$) an ideal inductor is a short circuit.
  • Capacitive reactance $\ X_C=\dfrac{1}{\omega C}=\dfrac{1}{2\pi\nu C}$ — falls with frequency; for DC a capacitor is an open circuit (it blocks steady current once charged).
📐 Result 14.13 — Single elements on an AC source

For a source $v=v_m\sin\omega t$ across a single ideal element:

ElementOppositionCurrentPhase of $i$Average power
$R$$R$$v_m/R$in phase$V_\text{rms}I_\text{rms}$
$L$$X_L=\omega L$$v_m/X_L$lags by $\pi/2$$0$
$C$$X_C=1/\omega C$$v_m/X_C$leads by $\pi/2$$0$

The same ratios hold for rms values: $I_\text{rms}=V_\text{rms}/X$.

Why is the average power zero for a pure inductor or capacitor? In one quarter cycle the element takes energy from the source and stores it (in the magnetic field of the inductor, $\tfrac12Li^2$, or the electric field of the capacitor, $\tfrac12Cv^2$); in the next quarter it gives all of it back. The instantaneous power $vi$ is positive and negative for equal times. A current flows and an ammeter reads it — but no energy is used up. A memory aid: in ELI the ICE man, $E$ (voltage) comes before $I$ in an inductor $L$, and $I$ comes before $E$ in a capacitor $C$.

✏️ Example 3 — An inductor and a capacitor on the mains
A pure inductor of $0.20\ \text{H}$ and, separately, a capacitor of $40\ \mu\text{F}$ are connected across a $220\ \text{V}$, $50\ \text{Hz}$ supply. (a) Find the reactance of each and the rms current each draws. (b) At what frequency would the two have equal reactances? (c) Find the average power taken by each, and explain why the ammeter still shows a current.
(a) $X_L=2\pi\times50\times0.20=62.8\ \Omega$, $I=\dfrac{220}{62.8}=3.50\ \text{A}$, lagging by $90^\circ$. $X_C=\dfrac{1}{2\pi\times50\times40\times10^{-6}}=79.6\ \Omega$, $I=\dfrac{220}{79.6}=2.76\ \text{A}$, leading by $90^\circ$.
(b) $2\pi\nu L=\dfrac{1}{2\pi\nu C}$ gives $\nu=\dfrac{1}{2\pi\sqrt{LC}}=\dfrac{1}{2\pi\sqrt{0.20\times40\times10^{-6}}}=56.3\ \text{Hz}$. (We meet this frequency again as the resonant frequency.)
(c) Zero for both. Energy flows into the element for a quarter cycle and back to the source the next quarter; the rms current $3.50\ \text{A}$ or $2.76\ \text{A}$ is real, but it carries energy back and forth without using any.
Check Raise the frequency and $X_L$ rises while $X_C$ falls: above $56.3\ \text{Hz}$ the capacitor would draw the larger current, below it the inductor.

In Interactive 1 choose the capacitor ($20\ \mu\text{F}$ on $220\ \text{V}$ rms) at $\nu=50\ \text{Hz}$. Now raise the frequency to $100\ \text{Hz}$. What happens to the rms current, and how does the current wave sit relative to the voltage wave?

At $50\ \text{Hz}$ the readouts show $X_C=159\ \Omega$ and $I_\text{rms}=1.38\ \text{A}$; at $100\ \text{Hz}$, $X_C=79.6\ \Omega$ and $I_\text{rms}=2.76\ \text{A}$ — doubled, because $X_C=1/2\pi\nu C$ halves. The current phasor stays $90^\circ$ ahead of the voltage phasor, and the current wave reaches its crest a quarter period before the voltage wave. Switch to the inductor ($0.50\ \text{H}$) to see the opposite: $X_L=157\ \Omega$, $I=1.40\ \text{A}$ at $50\ \text{Hz}$, falling to $0.70\ \text{A}$ at $100\ \text{Hz}$, with the current lagging. The mean power readout stays $0$ for both.
Interactive 1 — Phasors for R, L and C

A $220\ \text{V}$ (rms) source drives a single element: a $100\ \Omega$ resistor, a $0.50\ \text{H}$ inductor or a $20\ \mu\text{F}$ capacitor. On the left the voltage phasor (red) and current phasor (blue) rotate; their projections on the vertical axis trace the waves on the right. Press Play, change the element and the frequency, and watch the phase gap and the current.

50 Hz
$R$ or $X$—
$I_\text{rms}$—
current vs voltage—
mean power—

A capacitor is connected to an AC source of fixed rms voltage. If the frequency of the source is doubled, the rms current

The series LCR circuit: impedance and resonance

Now put a resistor $R$, an inductor $L$ and a capacitor $C$ in series across $v=v_m\sin\omega t$. The same current $i=i_m\sin(\omega t-\phi)$ flows through all three, so draw its phasor first, along the $x$-axis. Then the voltage phasors are: $V_R=i_mR$ along the current, $V_L=i_mX_L$ a quarter turn ahead (up), and $V_C=i_mX_C$ a quarter turn behind (down). $V_L$ and $V_C$ point in opposite directions, so they partly cancel, leaving $V_L-V_C$. Kirchhoff's loop rule holds at every instant, so the source phasor is the vector sum:

$$v_m=\sqrt{V_R^2+(V_L-V_C)^2}=i_m\sqrt{R^2+(X_L-X_C)^2}.$$
📘 Definition 14.10 — Impedance

The impedance $Z$ of an AC circuit is the ratio of the peak (or rms) source voltage to the peak (or rms) current, $Z=v_m/i_m=V_\text{rms}/I_\text{rms}$, whatever the phase difference. Its SI unit is the ohm. It is the AC counterpart of resistance, and it depends on frequency.

📐 Result 14.14 — Series LCR circuit

For $R$, $L$ and $C$ in series across a sinusoidal source of angular frequency $\omega$:

$$Z=\sqrt{R^2+(X_L-X_C)^2},\qquad \tan\phi=\frac{X_L-X_C}{R},$$

where $\phi$ is the angle by which the source voltage leads the current ($i=i_m\sin(\omega t-\phi)$). If $X_L\gt X_C$ the circuit is inductive ($\phi\gt0$, current lags); if $X_L\lt X_C$ it is capacitive ($\phi\lt0$, current leads). The impedance triangle has sides $R$, $X_L-X_C$ and hypotenuse $Z$, so $\cos\phi=R/Z$. For an RL circuit put $X_C=0$; for an RC circuit put $X_L=0$.

A striking consequence: voltmeters across $R$, $L$ and $C$ read $V_R$, $V_L$, $V_C$, and these rms readings do not add up to the source voltage. They add like the sides of a right-angled triangle, $V^2=V_R^2+(V_L-V_C)^2$ — the voltages reach their peaks at different instants.

🧭 Problem-solving strategy — Series AC circuits
  1. Find $\omega=2\pi\nu$, then $X_L=\omega L$ and $X_C=1/\omega C$ (missing elements: $X=0$).
  2. $Z=\sqrt{R^2+(X_L-X_C)^2}$ and $I_\text{rms}=V_\text{rms}/Z$.
  3. Phase: $\tan\phi=(X_L-X_C)/R$, $\cos\phi=R/Z$; say whether the current lags (inductive) or leads (capacitive).
  4. Element voltages $V_R=IR$, $V_L=IX_L$, $V_C=IX_C$ — check $V^2=V_R^2+(V_L-V_C)^2$.
  5. Power: $P=V_\text{rms}I_\text{rms}\cos\phi=I_\text{rms}^2R$ (next subsection).
✏️ Example 4 — A complete series LCR calculation
A $60\ \Omega$ resistor, a $0.16\ \text{H}$ inductor and a $12.5\ \mu\text{F}$ capacitor are in series across a source of rms voltage $200\ \text{V}$ and angular frequency $1000\ \text{rad/s}$. Find (a) the impedance and the rms current; (b) the readings of AC voltmeters across each element; (c) the phase angle, and whether the current leads or lags; (d) the average power taken from the source.
Find the average power in (d) before you open the solution:
(a) $X_L=1000\times0.16=160\ \Omega$; $X_C=\dfrac{1}{1000\times12.5\times10^{-6}}=80\ \Omega$. $Z=\sqrt{60^2+80^2}=100\ \Omega$; $I=\dfrac{200}{100}=2.0\ \text{A}$.
(b) $V_R=2.0\times60=120\ \text{V}$, $V_L=2.0\times160=320\ \text{V}$, $V_C=2.0\times80=160\ \text{V}$. Check: $\sqrt{120^2+(320-160)^2}=200\ \text{V}$ ✓ — although $120+320+160=600\ \text{V}$, and $V_L$ alone exceeds the source voltage.
(c) $\tan\phi=\dfrac{80}{60}$, $\phi=53^\circ$; $X_L\gt X_C$, so the circuit is inductive and the current lags the voltage by $53^\circ$.
(d) $P=I^2R=4.0\times60=240\ \text{W}$ (equally $VI\cos\phi=200\times2.0\times0.60=240\ \text{W}$).
⏱ Shortcut Spot the triangle: $R:(X_L-X_C)=60:80=3:4$, so $Z=100\ \Omega$ and $\cos\phi=0.6$ at once.

Resonance. As the source frequency changes, $X_L$ rises and $X_C$ falls. At one frequency they are equal, $V_L$ and $V_C$ cancel exactly, and the impedance is as small as it can be, $Z=R$.

📐 Result 14.15 — Resonance in a series LCR circuit

A series LCR circuit driven at a variable frequency is in resonance when $X_L=X_C$, that is at

$$\omega_0=\frac{1}{\sqrt{LC}},\qquad \nu_0=\frac{1}{2\pi\sqrt{LC}} .$$

At resonance: $Z=R$ (minimum), the current $I_\text{rms}=V_\text{rms}/R$ is a maximum, the current is in phase with the source ($\phi=0$), and the voltages across $L$ and $C$ are equal and opposite — each can be much larger than the source voltage. Below $\omega_0$ the circuit is capacitive; above it, inductive. Resonance needs both $L$ and $C$: an RL or RC circuit has none. The resonant frequency does not depend on $R$.

How sharp is the peak? A small resistance gives a tall, narrow peak (the circuit responds strongly only very near $\omega_0$); a large resistance gives a low, broad one. Two measures are used. The half-power frequencies $\omega_1$ and $\omega_2$ are where the power has fallen to half its peak value, i.e. where $I=I_\text{max}/\sqrt2$ and $Z=\sqrt2R$, which means $|X_L-X_C|=R$. The bandwidth is $\Delta\omega=\omega_2-\omega_1=R/L$.

📘 Definition 14.11 — Quality factor

The quality factor (Q-factor) of a series LCR circuit measures the sharpness of its resonance:

$$Q=\frac{\omega_0}{\Delta\omega}=\frac{\omega_0L}{R}=\frac{1}{\omega_0CR}=\frac1R\sqrt{\frac{L}{C}} .$$

It is a pure number. At resonance $V_L=V_C=Q\,V$, so $Q$ is also the factor by which the voltage across the inductor (or capacitor) exceeds the source voltage. A large $Q$ means a sharp, selective resonance.

Radio tuning uses exactly this. The aerial picks up signals from every station at once; the tuning circuit is an LC combination with a variable capacitor, and turning the knob changes $C$ until $\nu_0$ matches the wanted station. A high $Q$ lets that station through strongly and rejects its neighbours.

✏️ Example 5 — Tuning to resonance
A series circuit has $R=20\ \Omega$, $L=0.10\ \text{H}$ and $C=10\ \mu\text{F}$, driven by a $100\ \text{V}$ (rms) source of variable frequency. Find (a) the resonant angular frequency and frequency; (b) the rms current and the power at resonance; (c) the rms voltage across the capacitor at resonance; (d) the Q-factor and the bandwidth, and the two half-power angular frequencies.
Find the capacitor voltage at resonance, (c), first:
(a) $\omega_0=\dfrac{1}{\sqrt{0.10\times10\times10^{-6}}}=\dfrac{1}{10^{-3}}=1000\ \text{rad/s}$; $\nu_0=\dfrac{1000}{2\pi}=159\ \text{Hz}$.
(b) $Z=R=20\ \Omega$: $I=\dfrac{100}{20}=5.0\ \text{A}$; $P=I^2R=25\times20=500\ \text{W}$.
(c) $X_C=\dfrac{1}{1000\times10\times10^{-6}}=100\ \Omega$ ($=X_L$ ✓): $V_C=5.0\times100=500\ \text{V}$ — five times the supply voltage.
(d) $Q=\dfrac{\omega_0L}{R}=\dfrac{100}{20}=5.0$ (and $V_C=QV=500\ \text{V}$ ✓). $\Delta\omega=\dfrac{R}{L}=200\ \text{rad/s}$ ($31.8\ \text{Hz}$). Solving $\omega L-\dfrac{1}{\omega C}=\pm R$ gives $\omega_{1,2}=\sqrt{\left(\tfrac{R}{2L}\right)^2+\omega_0^2}\mp\tfrac{R}{2L}=1005\mp100$: $905\ \text{rad/s}$ and $1105\ \text{rad/s}$.
Check $1105-905=200=R/L$ ✓. The half-power points sit almost symmetrically about $\omega_0$ when $Q$ is large, $\omega_{1,2}\approx\omega_0\mp\tfrac{R}{2L}$.

In Interactive 2 set $L=0.50\ \text{H}$, $C=20\ \mu\text{F}$ and $R=50\ \Omega$, and press Play to sweep the frequency. Where is the peak of the current, how high is it — and what happens when you raise $R$ to $100\ \Omega$?

The readout shows $\nu_0=1/2\pi\sqrt{LC}=50.3\ \text{Hz}$ and $Q=3.16$. With the frequency slider at $50.5\ \text{Hz}$ (nearest to $\nu_0$) the readouts are $Z=50.0\ \Omega$, $I_\text{rms}=4.40\ \text{A}$, $\phi\approx1^\circ$ and $P=968\ \text{W}$ — the peak current is $V/R=220/50=4.4\ \text{A}$. With $R=100\ \Omega$ the resonant frequency is still $50.3\ \text{Hz}$ ($R$ does not appear in $\omega_0$), but the peak falls to $2.20\ \text{A}$ and $Q$ halves to $1.58$: a lower, broader curve. Away from resonance $R$ matters much less: at $30\ \text{Hz}$ the current is $1.23\ \text{A}$ with $R=50\ \Omega$ and $1.11\ \text{A}$ with $R=100\ \Omega$.
Interactive 2 — Series LCR Circuit: Phasors and the Resonance Curve

A $220\ \text{V}$ (rms) source of variable frequency drives $R$, $L$ and $C$ in series. Left: the voltage phasors (current along the horizontal) — $V_R$ green, $V_L$ red, $V_C$ blue, and the source voltage $V$ purple. Right: the rms current against frequency, with the half-power level dashed. Press Play to sweep the frequency through resonance; change $R$ to see the peak sharpen or flatten.

50 Ω0.50 H20 μF30 Hz
impedance $Z$—
$I_\text{rms}$—
phase $\phi$—
$\nu_0$ and $Q$—
power $P$—
🚀 Beyond JEE Main (JEE Advanced) — LC oscillations

LC oscillations are not in the JEE Main 2026 syllabus list (LC circuits are listed for JEE Advanced 2026; the topic is not in the CBSE syllabus). This box is for interest only; nothing here is used in the exercises, the Exam corner or the quiz.

Charge a capacitor $C$ to charge $q_0$ and connect it across an ideal inductor $L$, with no source and no resistance. The loop rule gives $L\dfrac{di}{dt}+\dfrac{q}{C}=0$ with $i=dq/dt$, so $\dfrac{d^2q}{dt^2}=-\dfrac{1}{LC}\,q$ — the equation of simple harmonic motion. The charge oscillates as $q=q_0\cos\omega_0t$ with $\omega_0=1/\sqrt{LC}$, exactly the resonant frequency above, and the current peaks at $i_0=\omega_0q_0$. Energy passes back and forth between the capacitor's electric field, $q^2/2C$, and the inductor's magnetic field, $\tfrac12Li^2$, like a mass on a spring swapping potential and kinetic energy ($L$ plays the part of mass, $1/C$ of the spring constant). With $L=0.10\ \text{H}$ and $C=10\ \mu\text{F}$ the circuit rings at $159\ \text{Hz}$. A real circuit has some resistance, so the oscillations die away — which is why a driven LCR circuit responds most strongly at its natural frequency $\omega_0$.

A series LCR circuit is driven at its resonant frequency. Which statement is correct?

Power in AC circuits, wattless current and the transformer

In an AC circuit the power delivered by the source at each instant is $p=vi$. With $v=v_m\sin\omega t$ and $i=i_m\sin(\omega t-\phi)$, the identity $2\sin A\sin B=\cos(A-B)-\cos(A+B)$ gives

$$p=\tfrac12v_mi_m\left[\cos\phi-\cos(2\omega t-\phi)\right].$$

The second term oscillates at twice the source frequency and averages to zero over a cycle. What remains is a steady average.

📐 Result 14.16 — Average power in an AC circuit

For a sinusoidal source driving a circuit in which the current differs in phase from the voltage by $\phi$, the average power taken from the source is

$$P=\tfrac12v_mi_m\cos\phi=V_\text{rms}I_\text{rms}\cos\phi .$$

In a series LCR circuit $\cos\phi=R/Z$, so $P=I_\text{rms}^2R$: only the resistance dissipates energy; the inductor and capacitor store and return it.

📘 Definition 14.12 — Power factor and wattless current

The power factor of an AC circuit is $\cos\phi=\dfrac{P}{V_\text{rms}I_\text{rms}}$ ($=R/Z$ for a series circuit). The product $V_\text{rms}I_\text{rms}$ is called the apparent power (unit volt-ampere, $\text{VA}$).

Resolve the current phasor into a component $I_\text{rms}\cos\phi$ in phase with the voltage and a component $I_\text{rms}\sin\phi$ at $90^\circ$ to it. Only the first carries power. The second, $I_\text{rms}\sin\phi$, is the wattless current: it flows in the wires (and heats them) but transfers no average power to the load.

The extremes: a pure resistor, or any series circuit at resonance, has $\phi=0$ and power factor $1$; a pure inductor or capacitor has $\phi=\pm90^\circ$ and power factor $0$ — all its current is wattless. Why does this matter? Electric companies must send the full current $I_\text{rms}$ down their lines, losing $I_\text{rms}^2R_\text{line}$ as heat, but are paid only for $V_\text{rms}I_\text{rms}\cos\phi$. Factories with large motors (inductive loads) therefore add capacitors in parallel to bring $\cos\phi$ close to $1$, reducing the current for the same useful power.

Choke coil. To run a low-voltage device from the mains you could put a resistor in series to drop the extra voltage — but the resistor would waste energy as heat. An inductor with very little resistance (a choke) drops the voltage instead, with almost no power loss, because its current is nearly wattless. Older fluorescent tubes used a choke for this reason.

The transformer. Two coils — the primary with $N_p$ turns and the secondary with $N_s$ turns — are wound on the same laminated soft-iron core. An alternating current in the primary sets up an alternating flux, and the iron core guides almost all of it through the secondary as well. Each turn of either coil links the same flux $\Phi_B$, so by Faraday's law the emfs are $\varepsilon_p=-N_p\,d\Phi_B/dt$ and $\varepsilon_s=-N_s\,d\Phi_B/dt$. If the primary resistance is negligible its emf balances the applied voltage, and if the secondary current is small (or the secondary resistance negligible) its terminal voltage equals its emf.

📐 Law 14.17 — The ideal transformer

For an ideal transformer (no flux leakage, no resistance in the windings, no energy lost in the core):

$$\frac{V_s}{V_p}=\frac{N_s}{N_p}=\frac{I_p}{I_s},\qquad V_pI_p=V_sI_s .$$

If $N_s\gt N_p$ it is a step-up transformer (voltage raised, current lowered); if $N_s\lt N_p$, step-down. A transformer conserves power, not voltage; it does not change the frequency; and it does not work on steady DC, because a steady current gives no changing flux. For a real transformer, the efficiency is $\eta=\dfrac{\text{output power}}{\text{input power}}=\dfrac{V_sI_s}{V_pI_p}\lt1$.

Large transformers reach efficiencies above $95\%$. The energy that is lost goes in four ways, each with its remedy:

Why transmit at high voltage? A power station must deliver power $P$ over lines of resistance $R_\text{line}$. Sent at voltage $V$, the current is $I=P/V$ and the line loss is $I^2R_\text{line}=\dfrac{P^2R_\text{line}}{V^2}$. Raising the voltage $50$ times cuts the loss $2500$ times. So the generator's output is stepped up to hundreds of kilovolts, carried across the country, and stepped down in stages (to $33\ \text{kV}$, $11\ \text{kV}$, and finally $230\ \text{V}$) near the consumer.

✏️ Example 6 — Stepping up for transmission
A power of $120\ \text{kW}$ is to be sent from a generator whose output is $220\ \text{V}$ to a town through lines of total resistance $0.20\ \Omega$. (a) Find the current and the power lost in the lines if the power is sent at $220\ \text{V}$. (b) The voltage is first stepped up to $11\ \text{kV}$ by an ideal transformer. Find the turns ratio, the line current and the line loss. (c) At the town an ideal step-down transformer with $1000$ turns in its primary brings the voltage back to about $220\ \text{V}$. How many turns has its secondary, and roughly what current does it supply? (Ignore the small voltage drop in the lines.)
Find the line loss in (b) before you open the solution:
(a) $I=\dfrac{120\,000}{220}=545\ \text{A}$; loss $=I^2R=545^2\times0.20=5.95\times10^4\ \text{W}\approx59.5\ \text{kW}$ — half the power wasted in the wires.
(b) $N_s:N_p=11\,000:220=50:1$. $I=\dfrac{120\,000}{11\,000}=10.9\ \text{A}$; loss $=10.9^2\times0.20=23.8\ \text{W}$, about $0.02\%$ of the power.
(c) Turns ratio $1:50$ again: $N_s=\dfrac{1000}{50}=20$ turns. Current $I_s=I_p\times\dfrac{N_p}{N_s}=10.9\times50=545\ \text{A}$ — the large current now flows only in the short local wiring.
⏱ Shortcut Loss $\propto1/V^2$: raising $V$ by $50$ divides the loss by $2500$: $59\,500/2500=23.8\ \text{W}$ ✓.
⚠️ JEE Main traps

1. Rms versus peak. "$220\ \text{V}$ AC" and meter readings are rms values; the peak is $\sqrt2$ times larger. $I_\text{rms}=i_m/\sqrt2$ only for a sine wave — for a square wave, a rectified wave or "DC plus AC", average $i^2$ yourself.

2. Adding voltages arithmetically. In a series AC circuit $V\ne V_R+V_L+V_C$; use $V^2=V_R^2+(V_L-V_C)^2$. A voltmeter across $L$ or $C$ may read more than the source.

3. $\omega$ versus $\nu$. $X_L=\omega L=2\pi\nu L$ and $X_C=1/2\pi\nu C$. Forgetting the $2\pi$ (or using $50$ where $100\pi$ is meant) is the commonest slip; read whether the problem gives $\nu$ or $\omega$.

4. Power is not $VI$. $P=V_\text{rms}I_\text{rms}\cos\phi=I_\text{rms}^2R$. Pure $L$ and $C$ take zero average power even though a current flows; and $V^2/R$ uses the voltage across $R$ only, not the source voltage.

5. Transformer rules. Voltage goes with turns, current goes against them ($I_p/I_s=N_s/N_p$); power, not voltage, is conserved; and a transformer on DC gives no output.

A coil of negligible resistance draws an rms current of $2.0\ \text{A}$ from a $220\ \text{V}$, $50\ \text{Hz}$ supply. The average power it takes is

Exercises

Treat inductors as pure (no resistance) and transformers as ideal unless told otherwise. Voltages and currents are rms values unless they are called peak values.

I
Alternating voltage, the AC generator and rms values.
  • 1 A voltage is $v=311\sin(100\pi t)$ volts. Find its peak value, rms value, frequency and period.
  • 2 Find the peak value and the peak-to-peak value of the $230\ \text{V}$ mains voltage.
  • 3 A $100\ \Omega$ heater is connected to $230\ \text{V}$ mains. Find the rms current, the peak current and the average power.
  • 4 A generator coil of $100$ turns, each of area $0.020\ \text{m}^2$, rotates at $50\ \text{rev/s}$ in a field of $0.50\ \text{T}$. Find the peak and rms emf.
  • 5 The coil of part 4 is turned twice as fast. What are the new peak emf and frequency?
  • 6 For $50\ \text{Hz}$ AC, find the time taken for the current to rise from zero to its peak, and from zero to half its peak.
  • 7 A sinusoidal current has peak $5.0\ \text{A}$. Find its mean value over a half cycle and over a full cycle.
  • 8 A current is $2.0\ \text{A}$ for half of each period and zero for the other half. Find its rms value. Compare with a square wave switching between $+2.0\ \text{A}$ and $-2.0\ \text{A}$.
1 $v_m=311\ \text{V}$; $V_\text{rms}=311/\sqrt2=220\ \text{V}$; $\omega=100\pi$, so $\nu=50\ \text{Hz}$ and $T=0.020\ \text{s}$.
2 $v_m=230\sqrt2=325\ \text{V}$; peak-to-peak $2v_m=651\ \text{V}$.
3 $I_\text{rms}=230/100=2.3\ \text{A}$; $i_m=2.3\sqrt2=3.25\ \text{A}$; $P=V_\text{rms}I_\text{rms}=529\ \text{W}$.
4 $\varepsilon_0=NBA\omega=100\times0.50\times0.020\times100\pi=314\ \text{V}$; $\varepsilon_\text{rms}=222\ \text{V}$.
5 $\varepsilon_0\propto\omega$ and $\nu$ = revolutions per second: $628\ \text{V}$ at $100\ \text{Hz}$.
6 Zero to peak is a quarter period: $T/4=5.0\ \text{ms}$. Half peak: $\omega t=\pi/6$, $t=T/12=1.67\ \text{ms}$ — the current rises fastest near zero.
7 Half cycle: $2i_m/\pi=10/\pi=3.18\ \text{A}$; full cycle: $0$.
8 $\langle i^2\rangle=\tfrac12\times4.0=2.0\ \text{A}^2$, $I_\text{rms}=\sqrt2=1.41\ \text{A}$. The square wave has $i^2=4.0\ \text{A}^2$ always, so $I_\text{rms}=2.0\ \text{A}$.
II
Reactance: inductors and capacitors on AC.
  • 1 Find the reactance of a $0.20\ \text{H}$ inductor at $50\ \text{Hz}$ and at $1.0\ \text{kHz}$.
  • 2 Find the reactance of a $10\ \mu\text{F}$ capacitor at $50\ \text{Hz}$ and at $1.0\ \text{kHz}$.
  • 3 At what frequency does a $2.0\ \mu\text{F}$ capacitor have a reactance of $1.0\ \text{k}\Omega$?
  • 4 A $0.35\ \text{H}$ inductor is connected to $220\ \text{V}$, $50\ \text{Hz}$. Find the rms current and the average power.
  • 5 Find the rms current drawn by a $50\ \mu\text{F}$ capacitor from $220\ \text{V}$, $50\ \text{Hz}$ mains.
  • 6 An inductor and a capacitor draw equal currents from the same $50\ \text{Hz}$ supply. The frequency is raised to $100\ \text{Hz}$ (same voltage). Find the ratio $I_C/I_L$.
  • 7 Explain why a capacitor blocks DC but passes AC, and why an ideal inductor connected straight to a DC battery would draw an ever-growing current.
  • 8 The current in a $0.10\ \text{H}$ inductor is $i=2.0\sin(100\pi t)$ amperes. Write the voltage across it and give its peak value.
1 $X_L=2\pi\nu L$: $62.8\ \Omega$ at $50\ \text{Hz}$; $1.26\ \text{k}\Omega$ at $1.0\ \text{kHz}$.
2 $X_C=1/2\pi\nu C$: $318\ \Omega$ at $50\ \text{Hz}$; $15.9\ \Omega$ at $1.0\ \text{kHz}$.
3 $\nu=\dfrac{1}{2\pi CX_C}=\dfrac{1}{2\pi\times2.0\times10^{-6}\times1000}=79.6\ \text{Hz}$.
4 $X_L=100\pi\times0.35=110\ \Omega$; $I=220/110=2.00\ \text{A}$, lagging by $90^\circ$; average power $0$.
5 $X_C=\dfrac{1}{100\pi\times50\times10^{-6}}=63.7\ \Omega$; $I=220/63.7=3.46\ \text{A}$.
6 $I_C\propto\nu$ doubles, $I_L\propto1/\nu$ halves: $I_C/I_L=4$.
7 For DC ($\nu=0$), $X_C\to\infty$: once charged, the capacitor carries no steady current. For AC it charges and discharges continually, so current flows in the wires. An ideal inductor has $X_L=0$ for DC and no resistance, so $L\,di/dt=\varepsilon$ makes the current grow steadily — in practice limited only by the resistance of the wire and the battery.
8 $v=L\dfrac{di}{dt}=0.10\times2.0\times100\pi\cos(100\pi t)=62.8\cos(100\pi t)\ \text{V}$: peak $62.8\ \text{V}$, leading the current by $90^\circ$.
III
Series LCR circuits and resonance.
  • 1 A series circuit has $R=40\ \Omega$, $X_L=100\ \Omega$, $X_C=70\ \Omega$ on a $200\ \text{V}$ supply. Find $Z$, the current and the phase angle, and say whether the current leads or lags.
  • 2 Find the readings of voltmeters across $R$, $L$ and $C$ in part 1 and show that they combine to give the supply voltage.
  • 3 $R=300\ \Omega$, $L=1.0\ \text{H}$ and $C=20\ \mu\text{F}$ are in series across $220\ \text{V}$, $50\ \text{Hz}$. Find the current and the power factor.
  • 4 Find the resonant angular frequency and frequency of a circuit with $L=25\ \text{mH}$ and $C=10\ \mu\text{F}$.
  • 5 What capacitance in series with a $0.20\ \text{H}$ inductor gives resonance at $50\ \text{Hz}$?
  • 6 $R=10\ \Omega$, $L=0.10\ \text{H}$, $C=10\ \mu\text{F}$ in series on a $100\ \text{V}$ variable-frequency source. Find the current at resonance, the voltage across the inductor then, and the Q-factor.
  • 7 Find the bandwidth $\Delta\omega$ and $\Delta\nu$ of the circuit in part 6.
  • 8 A radio tuning circuit has a $25\ \mu\text{H}$ coil. What capacitance tunes it to a $1.0\ \text{MHz}$ station?
  • 9 Below its resonant frequency, is a series LCR circuit inductive or capacitive? Explain using the reactances, and say what happens above resonance.
1 $Z=\sqrt{40^2+30^2}=50\ \Omega$; $I=200/50=4.0\ \text{A}$; $\tan\phi=30/40$, $\phi=37^\circ$; inductive, so the current lags by $37^\circ$.
2 $V_R=160\ \text{V}$, $V_L=400\ \text{V}$, $V_C=280\ \text{V}$; $\sqrt{160^2+(400-280)^2}=\sqrt{25\,600+14\,400}=200\ \text{V}$ ✓.
3 $X_L=100\pi\times1.0=314\ \Omega$, $X_C=\dfrac{1}{100\pi\times20\times10^{-6}}=159\ \Omega$; $Z=\sqrt{300^2+155^2}=338\ \Omega$; $I=220/338=0.651\ \text{A}$; $\cos\phi=300/338=0.888$ (lagging).
4 $\omega_0=\dfrac{1}{\sqrt{25\times10^{-3}\times10\times10^{-6}}}=\dfrac{1}{5.0\times10^{-4}}=2000\ \text{rad/s}$; $\nu_0=318\ \text{Hz}$.
5 $C=\dfrac{1}{\omega^2L}=\dfrac{1}{(100\pi)^2\times0.20}=5.07\times10^{-5}\ \text{F}=50.7\ \mu\text{F}$.
6 $\omega_0=1000\ \text{rad/s}$; $I=V/R=10\ \text{A}$; $X_L=100\ \Omega$, $V_L=10\times100=1000\ \text{V}$; $Q=\omega_0L/R=10$ (so $V_L=QV$ ✓).
7 $\Delta\omega=R/L=100\ \text{rad/s}$; $\Delta\nu=100/2\pi=15.9\ \text{Hz}$.
8 $C=\dfrac{1}{4\pi^2\nu^2L}=\dfrac{1}{4\pi^2\times10^{12}\times25\times10^{-6}}=1.01\times10^{-9}\ \text{F}=1.01\ \text{nF}$.
9 Below $\omega_0$, $X_C=1/\omega C$ is larger than $X_L=\omega L$, so $X_L-X_C\lt0$: capacitive, current leads. Above $\omega_0$, $X_L\gt X_C$: inductive, current lags.
IV
Power, wattless current and transformers.
  • 1 A circuit draws $5.0\ \text{A}$ from $220\ \text{V}$ with the current lagging by $60^\circ$. Find the average power.
  • 2 A coil draws $4.0\ \text{A}$ from a $12\ \text{V}$ DC supply and $2.4\ \text{A}$ from a $12\ \text{V}$, $50\ \text{Hz}$ AC supply. Find its resistance, its inductance, its power factor on AC and the power it takes on AC.
  • 3 A load draws $5.0\ \text{A}$ at power factor $0.80$. Find the wattless current and the in-phase (active) current.
  • 4 A transformer has $2300$ turns in its primary on $230\ \text{V}$ mains. How many secondary turns give $6.0\ \text{V}$? If the secondary supplies $2.0\ \text{A}$, find the primary current.
  • 5 A step-up transformer with turns ratio $1:20$ is fed with $230\ \text{V}$. Find the output voltage, and the input current when the output current is $0.10\ \text{A}$.
  • 6 A transformer delivers $900\ \text{W}$ while its primary takes $4.5\ \text{A}$ from $230\ \text{V}$ mains (power factor $1$). Find its efficiency.
  • 7 $100\ \text{kW}$ is sent through lines of total resistance $0.50\ \Omega$. Find the line loss at $2.5\ \text{kV}$ and at $250\ \text{V}$.
  • 8 Explain why a transformer core is laminated and made of soft iron, and why a transformer connected to a DC supply gives no output.
  • 9 A series LCR circuit with $R=20\ \Omega$ is on a $100\ \text{V}$ variable-frequency source. Find the power at resonance, and at a frequency where $X_L-X_C=20\ \Omega$.
1 $P=VI\cos\phi=220\times5.0\times0.50=550\ \text{W}$.
2 DC: $R=12/4.0=3.0\ \Omega$. AC: $Z=12/2.4=5.0\ \Omega$, $X_L=\sqrt{25-9}=4.0\ \Omega$, $L=\dfrac{4.0}{100\pi}=12.7\ \text{mH}$. $\cos\phi=R/Z=0.60$; $P=I^2R=2.4^2\times3.0=17.3\ \text{W}$.
3 $\sin\phi=0.60$: wattless $5.0\times0.60=3.0\ \text{A}$; active $5.0\times0.80=4.0\ \text{A}$.
4 $N_s=2300\times\dfrac{6.0}{230}=60$ turns; $I_p=I_s\dfrac{N_s}{N_p}=2.0\times\dfrac{60}{2300}=0.052\ \text{A}$.
5 $V_s=20\times230=4600\ \text{V}$; $I_p=20\times0.10=2.0\ \text{A}$.
6 Input $230\times4.5=1035\ \text{W}$; $\eta=900/1035=0.870=87.0\%$.
7 At $2.5\ \text{kV}$: $I=40\ \text{A}$, loss $40^2\times0.50=800\ \text{W}$ ($0.8\%$). At $250\ \text{V}$: $I=400\ \text{A}$, loss $80\ \text{kW}$ — $80\%$ of the power.
8 Thin insulated laminations cut the paths of eddy currents induced in the core, reducing their heating; soft iron is easily magnetised and demagnetised, so the hysteresis loss each cycle is small. On DC the flux is steady after switching on, so no emf is induced in the secondary (and the primary, with only its small resistance, draws a large current and may burn out).
9 At resonance $P=V^2/R=10\,000/20=500\ \text{W}$. With $X_L-X_C=R$: $Z=20\sqrt2\ \Omega$, $I=100/28.3=3.54\ \text{A}$, $P=I^2R=250\ \text{W}$ — this is a half-power frequency.
🎯 Exam corner JEE Main · MCQJEE Main · Numerical

E1. JEE Main · MCQ A series circuit with $R=30\ \Omega$, $X_L=90\ \Omega$ and $X_C=50\ \Omega$ is connected to a $100\ \text{V}$ (rms) AC source. The power factor and the average power taken by the circuit are (A) $0.6$ and $200\ \text{W}$ (B) $0.6$ and $120\ \text{W}$ (C) $0.8$ and $160\ \text{W}$ (D) $0.75$ and $120\ \text{W}$

Impedance $Z=\sqrt{30^2+(90-50)^2}=50\ \Omega$; $I=100/50=2.0\ \text{A}$.
Power $\cos\phi=R/Z=0.6$; $P=I^2R=4.0\times30=120\ \text{W}$ (or $100\times2.0\times0.6$).
Answer (B).
⏱ Shortcut (A) is $VI$, forgetting the power factor; (C) uses $X/Z$ instead of $R/Z$.

E2. JEE Main · Numerical A coil of inductance $0.10\ \text{H}$ and resistance $10\ \Omega$ is connected in series with a capacitor $C$ across a $200\ \text{V}$ (rms) source of variable frequency. When the frequency is adjusted for resonance, the rms voltage across the capacitor is $1000\ \text{V}$. Find $C$ in $\mu\text{F}$. Give the answer to the nearest integer.

Q-factor At resonance $V_C=QV$: $Q=1000/200=5$.
Frequency $Q=\dfrac{\omega_0L}{R}$: $\omega_0=\dfrac{5\times10}{0.10}=500\ \text{rad/s}$.
Capacitance $C=\dfrac{1}{\omega_0^2L}=\dfrac{1}{250\,000\times0.10}=4.0\times10^{-5}\ \text{F}=40\ \mu\text{F}$.
Answer $40$.
⏱ Shortcut $Q=\dfrac1R\sqrt{\dfrac LC}$ gives $C=\dfrac{L}{Q^2R^2}=\dfrac{0.10}{25\times100}=40\ \mu\text{F}$ in one line.

E3. JEE Main · MCQ The current in a circuit is $i=3+4\sin\omega t$ amperes. The reading of an rms (hot-wire) ammeter in the circuit is (A) $5\ \text{A}$ (B) $3+2\sqrt2\ \text{A}$ (C) $\tfrac{7}{\sqrt2}\ \text{A}$ (D) $\sqrt{17}\ \text{A}$

Square $i^2=9+24\sin\omega t+16\sin^2\omega t$.
Average $\langle\sin\omega t\rangle=0$, $\langle\sin^2\omega t\rangle=\tfrac12$: $\langle i^2\rangle=9+8=17\ \text{A}^2$.
Answer (D) $\sqrt{17}\approx4.12\ \text{A}$.
⏱ Shortcut For DC plus a sine, $I_\text{rms}=\sqrt{I_\text{dc}^2+i_m^2/2}$. (B) adds the two "rms" parts as if they were in step; (C) treats $7$ as a sine amplitude.

E4. JEE Main · Numerical A step-down transformer reduces $2200\ \text{V}$ to $220\ \text{V}$ and supplies $9.9\ \text{kW}$ to a load. If its efficiency is $90\%$, find the current in its primary coil in amperes. Give the answer to the nearest integer.

Input $P_\text{in}=\dfrac{P_\text{out}}{\eta}=\dfrac{9900}{0.90}=11\,000\ \text{W}$.
Current $I_p=\dfrac{P_\text{in}}{V_p}=\dfrac{11\,000}{2200}=5.0\ \text{A}$.
Answer $5$.
⏱ Shortcut The trap answer $4.5\ \text{A}$ uses the output power; a lossy transformer takes more from the primary than it delivers.

E5. JEE Main · MCQ A coil connected to a $200\ \text{V}$, $50\ \text{Hz}$ supply takes an rms current of $4.0\ \text{A}$ and consumes $480\ \text{W}$. The wattless component of the current is (A) $2.4\ \text{A}$ (B) $4.0\ \text{A}$ (C) $3.2\ \text{A}$ (D) $0.8\ \text{A}$

Power factor $\cos\phi=\dfrac{P}{VI}=\dfrac{480}{800}=0.60$, so $\sin\phi=0.80$.
Wattless $I\sin\phi=4.0\times0.80=3.2\ \text{A}$.
Answer (C).
⏱ Shortcut (A) $=I\cos\phi$ is the active (power-carrying) component — the opposite one.

E6. JEE Main · Numerical A lamp rated $60\ \text{W}$, $120\ \text{V}$ is to be run at its rated values from a $200\ \text{V}$, $50\ \text{Hz}$ supply by putting a pure inductor in series with it. Find the reactance of the inductor in ohms. Give the answer to the nearest integer.

Lamp $I=P/V=60/120=0.50\ \text{A}$ (and $R=120^2/60=240\ \Omega$).
Phasors $V_L=\sqrt{200^2-120^2}=160\ \text{V}$ — not $200-120=80\ \text{V}$.
Reactance $X_L=V_L/I=160/0.50=320\ \Omega$ (so $L=320/100\pi=1.02\ \text{H}$).
Answer $320$.
⏱ Shortcut $200:120:160=5:3:4$ — the voltage triangle is a 3-4-5 triangle. A choke wastes no power; a $160\ \Omega$ resistor (from $80\ \text{V}/0.5\ \text{A}$) could not even do the job.
🔬 Research–Teaching NexusResearch-tutored · optional, about 60 minutes

Research question. How sharply does a series LCR circuit pick out its resonant frequency, and how does the resistance in the circuit change that sharpness?

Why it matters. Resonant circuits are everywhere in modern technology. A radio or television tuner, the coils that charge a phone wirelessly, the RF coils of a hospital MRI scanner, metal detectors at airports and the contactless chips in bank cards and metro passes all rely on an LC circuit tuned to one frequency. Engineers choose the quality factor deliberately: high $Q$ for selecting one signal among many, lower $Q$ when a range of frequencies must pass. Power engineers meet resonance as a hazard: the capacitors added to factories for power-factor correction can resonate with the inductance of the supply and produce damaging overvoltages.

What to do.

  1. Build a series circuit from a coil (a few tens of millihenries — a solenoid or a small transformer winding), a capacitor of a few microfarads and a $10$–$100\ \Omega$ resistor. Drive it from a signal generator, or from a phone or laptop headphone output playing tones from a free tone-generator app.
  2. Keeping the source amplitude fixed, measure the voltage across the resistor with a multimeter (AC range) at frequencies from well below to well above $\nu_0=1/2\pi\sqrt{LC}$. The current is $V_R/R$.
  3. Plot the current against frequency. Read off the peak frequency and the two frequencies where the current is $1/\sqrt2$ of its peak.
  4. Compute $Q=\nu_0/\Delta\nu$ and compare it with $\tfrac1R\sqrt{L/C}$, remembering to include the coil's own resistance in $R$.
  5. Repeat with a larger resistor and overlay the two curves.

Tools: Coil, capacitor, resistors, signal generator or phone/laptop tone app, digital multimeter, breadboard and leads, spreadsheet or graph paper.

Hand in: A table and graph of current against frequency for both resistances, your measured $\nu_0$ and $Q$ compared with the predicted values, and a paragraph explaining the differences.

Going further. Measure $V_L$ and $V_C$ at resonance. Are they equal, and is each about $Q$ times the source voltage? Then find out how a wireless charging pad and its phone are both tuned to the same frequency, and why the charging becomes much less efficient if the phone is moved off-centre.

Instructor note: phone and laptop outputs are low-voltage and safe; never use mains for this experiment. Cheap multimeters lose accuracy above a few kHz, so choose $L$ and $C$ to put $\nu_0$ between about $200\ \text{Hz}$ and $2\ \text{kHz}$ (e.g. $L=50\ \text{mH}$, $C=1\ \mu\text{F}$ gives $712\ \text{Hz}$). The coil's resistance usually dominates $R$ and its iron core (if any) adds losses, so measured $Q$ values come out below the simple formula — a useful discussion point.

🧪 Self-check quiz

0/5 correct

Q1. The peak value of an alternating voltage whose rms value is $220\ \text{V}$ is about

Q2. In a pure capacitor connected to an AC source, the current

Q3. In a series LCR circuit $R=8\ \Omega$, $X_L=10\ \Omega$ and $X_C=16\ \Omega$. The impedance and the nature of the circuit are

Q4. The resonant frequency of a series LCR circuit is $\nu_0$. If the capacitance is made four times as large (with $L$ and $R$ unchanged), the resonant frequency becomes

Q5. An ideal transformer has $100$ turns in its primary and $500$ turns in its secondary. If the primary is connected to $220\ \text{V}$ AC and draws $5.0\ \text{A}$, the secondary voltage and current are