14.1 Faraday's Law, Lenz's Law and Motional EMF
Change the magnetic flux through a circuit and an emf appears in it: $\varepsilon=-N\,d\Phi_B/dt$. The minus sign is Lenz's law — the induced current always opposes the change — and a conductor moving through a field carries its own emf, $\varepsilon=Blv$.
In 1831 Michael Faraday wound two coils of wire on one iron ring, connected a battery to the first and a galvanometer to the second, and watched. With a steady current in the first coil, the galvanometer showed nothing. But at the instant he closed the switch the needle kicked one way, and at the instant he opened it the needle kicked the other way. Pushing a bar magnet into a coil did the same thing; holding the magnet still inside the coil did nothing. Joseph Henry in America found the same effect at about the same time. A magnetic field can drive a current — but only while something is changing.
That discovery, electromagnetic induction, is how almost all the world's electricity is generated: in power stations, wind turbines and car alternators a magnet and a coil move relative to each other. It also runs induction cooktops, wireless phone chargers, card readers and the guitar pick-up. In this section we define magnetic flux, state Faraday's law for the size of the induced emf and Lenz's law for its direction, show that Lenz's law is energy conservation in disguise, and work out the emf of a conductor moving through a field — a rod sliding on rails and a rod or disc spinning in a field — the problems JEE Main asks every year.
Magnetic flux and electromagnetic induction
Faraday's experiments all have one feature in common. In each case, the number of magnetic field lines threading the coil was changing: the magnet came nearer (more lines), went away (fewer lines), or the current in the first coil grew or died away. The quantity that measures "how much field passes through a surface" is the magnetic flux, defined exactly like the electric flux of Section 11.2.
For a flat surface of area $A$ in a uniform magnetic field $\mathbf B$, the magnetic flux through the surface is
$$\Phi_B=\mathbf B\cdot\mathbf A=BA\cos\theta,$$where the area vector $\mathbf A$ has magnitude $A$ and points along the normal to the surface, and $\theta$ is the angle between $\mathbf B$ and that normal. If the field varies over the surface, divide it into small pieces and add: $\Phi_B=\displaystyle\int\mathbf B\cdot d\mathbf A$. Flux is a scalar (it can be positive, negative or zero). Its SI unit is the weber: $1\ \text{Wb}=1\ \text{T m}^2$; dimensions $[\text{ML}^2\text{T}^{-2}\text{A}^{-1}]$. For a coil of $N$ identical turns the total flux linkage is $N\Phi_B$.
The formula shows the three ways to change the flux through a loop: change the field $B$ (move a magnet, change a current), change the area $A$ (slide a rod along rails, squeeze the loop), or change the angle $\theta$ (rotate the coil — the principle of the generator, taken up in Section 14.3). Flux is greatest, $BA$, when the field is perpendicular to the plane of the loop ($\theta=0^\circ$), and zero when the field lies in the plane ($\theta=90^\circ$).
Electromagnetic induction is the production of an emf in a circuit whenever the magnetic flux linked with it changes. The emf is called the induced emf; if the circuit is closed it drives an induced current $I=\varepsilon/R$, where $R$ is the total resistance of the circuit. The emf exists even if the circuit is open — then it simply appears as a potential difference across the gap.
An induced emf is not produced by charges at rest, so it is not an electrostatic effect. A changing magnetic field produces an induced electric field whose lines close on themselves; it pushes charges round the loop, and the work it does on unit charge in one trip round is the emf. (An electrostatic field could never do that: its work round a closed path is zero.)
A flat loop of area $A$ lies in a uniform field $B$ that makes an angle of $30^\circ$ with the plane of the loop. The flux through the loop is
Faraday's law and the induced current
Faraday found that the size of the induced emf depends not on how large the flux is, but on how fast it changes: push the magnet in quickly and the galvanometer kicks hard; push it slowly and the kick is small; hold it still and there is none. Coils with more turns give proportionally more emf, because each turn contributes the same emf and the turns are in series.
The emf induced in a coil of $N$ turns equals the negative of the rate of change of the flux linked with it:
$$\varepsilon=-N\frac{d\Phi_B}{dt}.$$If the flux changes by $\Delta\Phi_B$ in a time $\Delta t$, the average induced emf is $\varepsilon_\text{av}=-N\dfrac{\Delta\Phi_B}{\Delta t}$. The law holds whatever causes the change — a changing field, a changing area or a changing orientation. The minus sign gives the direction of the emf (Lenz's law, below); for magnitudes we use $|\varepsilon|=N\left|\dfrac{d\Phi_B}{dt}\right|$.
For a coil whose area and orientation are fixed in a field perpendicular to its plane, $\varepsilon=-NA\,\dfrac{dB}{dt}$. For a loop whose area changes in a fixed perpendicular field, $\varepsilon=-NB\,\dfrac{dA}{dt}$. If both change, use the product rule on $\Phi_B=BA$.
The charge that flows. If the coil is part of a closed circuit of total resistance $R$, the induced current is $I=\dfrac{|\varepsilon|}{R}=\dfrac{N}{R}\left|\dfrac{d\Phi_B}{dt}\right|$. The charge that passes in a short time $dt$ is $dq=I\,dt=\dfrac{N}{R}|d\Phi_B|$. Adding these up while the flux changes steadily in one direction:
When the flux linked with a coil of $N$ turns changes by $\Delta\Phi_B$ (always in the same direction), the charge that flows through a circuit of total resistance $R$ is
$$q=\frac{N\,|\Delta\Phi_B|}{R}.$$It depends only on the total change of flux and the resistance — not on how quickly the change happens. If the flux first falls and then rises, the current reverses: the net charge is still $N|\Phi_\text{final}-\Phi_\text{initial}|/R$, but the total charge that has passed (counting both directions) is $N/R$ times the sum of the separate changes.
This is why a "search coil" connected to a ballistic galvanometer measures magnetic fields: flip the coil over in the field (or pull it out of the field), and the charge that flows tells you $\Delta\Phi_B$, whether you did it quickly or slowly.
- Write the flux through one turn, $\Phi_B=BA\cos\theta$, as a function of time (or find its initial and final values). Check which angle you are given.
- Differentiate for the instantaneous emf, or divide $\Delta\Phi_B$ by $\Delta t$ for the average emf; multiply by $N$.
- Current: $I=\varepsilon/R_\text{total}$ (coil resistance plus anything in series). Charge: $q=N|\Delta\Phi_B|/R$, with no time needed.
- Direction: use Lenz's law (next subsection), not the minus sign by itself.
A bar magnet is pushed fully into a coil connected to a resistor, once slowly and once quickly. Compared with the slow push, the quick push gives
Lenz's law and conservation of energy
Faraday's law gives the size of the emf. Its direction was stated in 1834 by Heinrich Lenz in a form that is easy to use and easy to remember.
The direction of an induced current is such that it opposes the change in magnetic flux that produces it. (If the circuit is open, the induced emf has the direction in which such a current would flow.) This is the meaning of the minus sign in $\varepsilon=-N\,d\Phi_B/dt$.
Read the law carefully: the induced current opposes the change, not the field. If the flux through a loop is increasing, the induced current makes its own field opposite to the external field inside the loop. If the flux is decreasing, the induced current makes a field in the same direction, trying to keep the flux up. To turn "field inside the loop" into a direction of current, use the right-hand rule for a loop: curl the fingers of your right hand along the current, and your thumb points along the field inside the loop. Equivalently, a loop whose current looks anticlockwise from one side presents a north face to that side; clockwise means a south face.
- North pole pushed towards a coil. The flux through the coil increases; the coil opposes this by turning its near face into a north pole, which repels the magnet. Seen from the magnet, the current is anticlockwise.
- North pole pulled away. The flux decreases; the near face becomes a south pole, which attracts the magnet back. Seen from the magnet, the current is clockwise.
Either way, the coil resists the motion: you must do work to push the magnet in and work to pull it out. That work is exactly where the electrical energy comes from.
Why it cannot be the other way. Suppose the induced current helped the change: an approaching north pole would meet a south face and be pulled in faster, which would increase the flux faster, which would increase the current and the pull — a magnet given the slightest nudge would accelerate for ever, producing kinetic energy and electrical energy from nothing. Lenz's law is therefore required by the law of conservation of energy: the mechanical work done against the opposing magnetic force equals the electrical energy generated, which ends up as heat $I^2R$ in the circuit. We will check this balance exactly for the sliding rod in the next subsection.
In Interactive 1 set $N=100$ turns, magnet strength $1.0\ \text{mWb}$ and speed $0.50\ \text{m/s}$: the peak emf reads $0.859\ \text{V}$. Predict the peak emf when you raise the speed to $1.00\ \text{m/s}$.
A bar magnet is dropped, north pole downward, through a horizontal copper ring. While the magnet is below the ring and moving away from it, the magnet's acceleration is
Motional emf
So far the flux changed because the field changed. Now keep the field steady and move a conductor through it. Take a straight rod of length $l$ moving with velocity $\mathbf v$ through a uniform field $\mathbf B$, with $l$, $\mathbf v$ and $\mathbf B$ mutually perpendicular. Each free electron in the rod moves with the rod, so it feels a magnetic force $q\mathbf v\times\mathbf B$ along the rod. Electrons pile up at one end, leaving the other end positive, until the electric field $E$ they create balances the magnetic force: $qE=qvB$. The potential difference between the ends is then $El=Blv$. The rod acts like a cell — its emf comes from the magnetic force on the moving charges.
The same answer comes from Faraday's law. Let the rod slide along two parallel rails a distance $l$ apart, joined at one end, so that it closes a rectangle whose length $x$ grows at the rate $dx/dt=v$. The flux through the rectangle is $\Phi_B=Blx$, so $|\varepsilon|=\dfrac{d\Phi_B}{dt}=Bl\dfrac{dx}{dt}=Blv$.
A straight conductor of length $l$ moving with velocity $\mathbf v$ in a uniform magnetic field $\mathbf B$ has an emf between its ends of
$$\varepsilon=Blv\qquad(l,\ \mathbf v,\ \mathbf B\ \text{mutually perpendicular}).$$In general only the components count: $\varepsilon=(\mathbf v\times\mathbf B)\cdot\mathbf l$. The emf is zero if the rod moves along its own length, or parallel to $\mathbf B$, or if the rod lies along $\mathbf B$. The end towards which $\mathbf v\times\mathbf B$ points is the positive end (positive charges are pushed there). For a curved wire moving with velocity $\mathbf v$, $l$ is replaced by the length of the straight line joining its ends, projected perpendicular to $\mathbf v$ and $\mathbf B$.
The rod on rails — energy balance. Join the rails through a resistor $R$ (rod and rails of negligible resistance). The current is $I=\dfrac{Blv}{R}$, and the field exerts a force on the current-carrying rod of size $F_B=BIl=\dfrac{B^2l^2v}{R}$, directed against the velocity (Lenz's law). To keep the rod moving at constant speed an agent must push with an equal force, delivering power
$$P=F_Bv=\frac{B^2l^2v^2}{R}=\frac{\varepsilon^2}{R}=I^2R,$$exactly the rate at which heat is produced in the resistor. Mechanical work becomes electrical energy becomes heat — Lenz's law and energy conservation in one line.
A rod of mass $m$ and length $l$ slides on smooth horizontal rails joined through a resistance $R$, in a uniform vertical field $B$. The magnetic braking force is $\dfrac{B^2l^2v}{R}$, proportional to the speed. Writing $\tau=\dfrac{mR}{B^2l^2}$:
- Pulled by a constant force $F$ from rest: $m\dfrac{dv}{dt}=F-\dfrac{B^2l^2v}{R}$, so $v=v_t\left(1-e^{-t/\tau}\right)$ with terminal speed $v_t=\dfrac{FR}{B^2l^2}$.
- Given a speed $v_0$ and released: $v=v_0e^{-t/\tau}$; it stops after a distance $x=\dfrac{mv_0R}{B^2l^2}$, and all of its kinetic energy $\tfrac12mv_0^2$ becomes heat.
- A rod sliding down vertical rails reaches $v_t=\dfrac{mgR}{B^2l^2}$ (put $F=mg$).
(The exponentials follow from separating the variables: $\dfrac{dv}{v_t-v}=\dfrac{dt}{\tau}$ integrates to $\ln\dfrac{v_t}{v_t-v}=\dfrac t\tau$. The stopping distance comes from $m\,v\dfrac{dv}{dx}=-\dfrac{B^2l^2v}{R}$, so $m\,dv=-\dfrac{B^2l^2}{R}dx$: the speed falls linearly with distance.)
A rotating rod. A rod of length $l$ rotates with angular velocity $\omega$ about one end, in a plane perpendicular to a uniform field $B$. Different parts of the rod move at different speeds: a small piece $dr$ at distance $r$ from the axis moves at $v=\omega r$ and contributes $d\varepsilon=B(\omega r)\,dr$. Adding up from $0$ to $l$:
The emf between the ends of a rod of length $l$ rotating about one end with angular speed $\omega$, in a plane perpendicular to a uniform field $B$, is
$$\varepsilon=\int_0^lB\omega r\,dr=\tfrac12B\omega l^2.$$It is the emf of a rod moving with its average speed $\tfrac12\omega l$. A metal disc of radius $R$ rotating about its axis parallel to $B$ (Faraday's disc) has emf $\tfrac12B\omega R^2$ between centre and rim — it behaves like many such rods in parallel. Between two points at distances $r_1$ and $r_2$ from the axis on the same rod, $\varepsilon=\tfrac12B\omega(r_2^2-r_1^2)$.
In Interactive 2 choose "pulled by a constant force" with $B=0.50\ \text{T}$, $R=2.0\ \Omega$, $F=0.20\ \text{N}$: the rod settles at $10.0\ \text{m/s}$ with $1.00\ \text{A}$. Predict the terminal speed when you raise $B$ to $1.00\ \text{T}$.
1. Angle with the plane or with the normal? $\Phi_B=BA\cos\theta$ uses the angle between $\mathbf B$ and the normal. "Field at $30^\circ$ to the plane" means $\theta=60^\circ$.
2. Induced charge does not depend on time. $q=N|\Delta\Phi_B|/R$ — the speed of the change cancels. But if the flux turns back during the interval, the net and the total charge differ: split at the turning point.
3. Lenz's law opposes the change, not the field. A decreasing flux produces a current whose field is in the same direction as the external field. And the opposing force always slows the motion — a falling magnet has $a\lt g$ both above and below a ring.
4. Motional emf needs perpendicular components. $\varepsilon=Blv$ only when $l$, $v$ and $B$ are mutually perpendicular; a rod moving along its length or along $B$ has no emf. For a rotating rod use $\tfrac12B\omega l^2$ (not $B\omega l^2$); a rod spinning about its midpoint has zero emf between its ends.
5. Magnetic braking grows with speed. The force on a rod on rails is $B^2l^2v/R$, so a constant pull gives a terminal speed $FR/B^2l^2$, not a constant acceleration. Don't forget the resistance of the rod itself if it is given — it adds to $R$.
A metal rod of length $l$ rotates about its midpoint with angular speed $\omega$ in a plane perpendicular to a uniform field $B$. The emf between its two ends is
Exercises
Unless told otherwise, fields are uniform, rails are smooth and the resistance of rods and rails is negligible. Take $g=9.8\ \text{m/s}^2$.
- 1 A rectangular loop $20\ \text{cm}\times10\ \text{cm}$ is in a field of $0.50\ \text{T}$ whose direction makes $30^\circ$ with the normal to the loop. Find the flux through it.
- 2 Through what angle (between $\mathbf B$ and the normal) must a loop be turned from the position of maximum flux for the flux to fall to half its maximum?
- 3 A coil of $500$ turns and area $4.0\ \text{cm}^2$ lies perpendicular to a field that falls steadily from $0.80\ \text{T}$ to zero in $0.10\ \text{s}$. Find the induced emf.
- 4 The coil of part 3 has a total resistance of $8.0\ \Omega$. Find the induced current and the charge that flows.
- 5 The flux through each turn of a $20$-turn coil is $\Phi_B=(5t^2+3t+2)\ \text{mWb}$ ($t$ in s). Find the induced emf at $t=3.0\ \text{s}$.
- 6 A $100$-turn coil of area $50\ \text{cm}^2$ lies perpendicular to a field $B=B_0\sin\omega t$ with $B_0=0.020\ \text{T}$ and $\omega=100\pi\ \text{rad/s}$. Find the largest emf induced.
- 7 A flexible circular loop in a perpendicular field of $0.50\ \text{T}$ is shrinking: at the instant its radius is $10\ \text{cm}$, the radius decreases at $2.0\ \text{mm/s}$. Find the emf, in mV.
- 8 A search coil of $50$ turns and area $20\ \text{cm}^2$ lies perpendicular to a field of $0.30\ \text{T}$. It is flipped over through $180^\circ$; the total resistance of the circuit is $3.0\ \Omega$. Find the charge that flows.
- 1 The north pole of a magnet is moved away from the face of a coil. What pole appears on that face, and which way does the current circulate as seen from the magnet?
- 2 Two coaxial loops A and B face each other. A switch is closed so that a current starts in A, anticlockwise as seen from B. Say whether the current induced in B circulates in the same sense as A's current or the opposite sense (both seen from the same side) while A's current grows, once it is steady, and when the switch is opened.
- 3 A square loop is being pulled to the right out of a region where the field points into the page. Find the direction of the induced current and of the magnetic force on the loop.
- 4 A rectangular loop moves away from a long straight wire that carries a steady current, staying in the same plane. Is the loop attracted or repelled by the wire while it moves? Explain with Lenz's law.
- 5 A magnet falls through a copper ring. At the instant the middle of the magnet is at the ring, what is the induced current, and what is the magnet's acceleration?
- 6 A square loop of side $10\ \text{cm}$ and resistance $0.50\ \Omega$ is pulled out of a field of $0.40\ \text{T}$ (perpendicular to the loop) at a steady $2.0\ \text{m/s}$, with one side still inside the field. Find the force needed and the power delivered by it.
- 7 Show that if induced currents aided the change of flux, a magnet near a coil could gain kinetic energy without limit. What law would this break?
- 8 For the loop of part 6, find the work done in pulling it completely out of the field, and say where that energy goes.
- 1 A rod $0.50\ \text{m}$ long moves at $4.0\ \text{m/s}$ perpendicular to itself and to a field of $0.25\ \text{T}$. Find the emf.
- 2 The axle of a truck, $1.5\ \text{m}$ long, moves horizontally at $30\ \text{m/s}$ where the vertical component of the Earth's field is $4.0\times10^{-5}\ \text{T}$. Find the emf between the ends of the axle, in mV.
- 3 A rod $0.50\ \text{m}$ long lies in a plane perpendicular to a $0.40\ \text{T}$ field and moves in that plane at $5.0\ \text{m/s}$ in a direction making $60^\circ$ with its own length. Find the emf.
- 4 An aircraft with a wing span of $40\ \text{m}$ flies horizontally at $250\ \text{m/s}$ where the vertical component of the Earth's field is $3.0\times10^{-5}\ \text{T}$. Find the emf between the wing tips. Could a voltmeter on board measure it?
- 5 A rod $20\ \text{cm}$ long rotates about one end at $50\ \text{rad/s}$ in a plane perpendicular to a $0.40\ \text{T}$ field. Find the emf between its ends.
- 6 A bicycle wheel with $10$ metal spokes, each $0.50\ \text{m}$ long, turns at $2.0\ \text{rev/s}$ with its axle parallel to a field of $4.0\times10^{-4}\ \text{T}$. Find the emf between the axle and the rim, in mV. Does it depend on the number of spokes?
- 7 A rod $0.30\ \text{m}$ long slides at a steady $2.0\ \text{m/s}$ on rails joined by a $1.5\ \Omega$ resistor, in a perpendicular field of $0.50\ \text{T}$. Find the current and the force needed to keep the speed constant.
- 8 For part 7, find the mechanical power supplied and show that it equals the rate of heating of the resistor.
- 1 A rod of mass $20\ \text{g}$ and length $0.50\ \text{m}$ slides without friction down a pair of vertical rails joined at the top by a $0.80\ \Omega$ resistor, in a horizontal field of $0.40\ \text{T}$ perpendicular to the rails' plane. Find its terminal speed.
- 2 A rod of mass $0.050\ \text{kg}$ and length $0.25\ \text{m}$ on horizontal rails joined by a $0.50\ \Omega$ resistor, in a vertical field of $0.80\ \text{T}$, is given a speed of $6.0\ \text{m/s}$ and released. How far does it slide before stopping? How much heat is produced?
- 3 For part 2, find the total charge that flows through the resistor.
- 4 A square loop of side $20\ \text{cm}$ and resistance $0.40\ \Omega$ moves at a steady $1.0\ \text{m/s}$ through a region $50\ \text{cm}$ wide containing a field of $0.50\ \text{T}$ perpendicular to the loop. Describe the emf as a function of time and find the total heat produced while the loop crosses the region.
- 5 A rod slides on rails $0.20\ \text{m}$ apart, forming a rectangle with the closed end. At one instant the rod is $0.50\ \text{m}$ from the closed end and moving away at $2.0\ \text{m/s}$, while the perpendicular field is $0.10\ \text{T}$ and increasing at $0.40\ \text{T/s}$. Find the emf at that instant.
- 6 A wire bent into a semicircle of radius $10\ \text{cm}$ moves at $3.0\ \text{m/s}$ in its own plane, perpendicular to the diameter joining its ends, in a perpendicular field of $0.50\ \text{T}$. Find the emf between its ends.
- 7 Each blade of a helicopter rotor is $5.0\ \text{m}$ long and turns at $6.0\ \text{rev/s}$ in a horizontal plane where the vertical component of the Earth's field is $4.0\times10^{-5}\ \text{T}$. Find the emf between the hub and a blade tip, in mV.
E1. JEE Main · MCQ A coil of $100$ turns, each of area $0.010\ \text{m}^2$, is connected in a circuit of total resistance $10\ \Omega$. It is placed with its plane perpendicular to a uniform field of $0.50\ \text{T}$ and then turned through $90^\circ$ in $0.10\ \text{s}$, so that its plane becomes parallel to the field. The charge that flows through the circuit is (A) $0.50\ \text{C}$ (B) $0.050\ \text{C}$ (C) $0.10\ \text{C}$ (D) $5.0\ \text{mC}$
E2. JEE Main · Numerical A conducting rod of length $0.40\ \text{m}$ is pulled along smooth horizontal rails by a constant force of $0.80\ \text{N}$. The rails are joined by a $0.50\ \Omega$ resistor and lie in a vertical uniform field of $0.50\ \text{T}$; other resistances are negligible. After a long time, what is the rate of heating of the resistor, in watts? Give the answer to the nearest integer.
E3. JEE Main · MCQ A small copper ring lies flat on a table. A bar magnet held vertically above it with its south pole downward is released and falls towards the ring. As seen from above, while the magnet approaches the ring, (A) the induced current is anticlockwise and the magnet is attracted (B) the induced current is anticlockwise and the magnet is repelled (C) the induced current is clockwise and the magnet is repelled (D) there is no induced current until the magnet enters the ring
E4. JEE Main · Numerical A metal rod $2.0\ \text{m}$ long rotates at $50\ \text{rad/s}$ in a plane perpendicular to a uniform field of $0.30\ \text{T}$, about an axis through a point $0.50\ \text{m}$ from one end. Find the emf, in volts, between the two ends of the rod. Give the answer to the nearest integer.
E5. JEE Main · MCQ The flux through a single loop of resistance $2.0\ \Omega$ is $\Phi_B=(t^2-4t)\ \text{mWb}$, with $t$ in seconds. The total charge that passes a point of the loop between $t=0$ and $t=4\ \text{s}$, counting both directions of flow, is (A) zero (B) $2.0\ \text{mC}$ (C) $4.0\ \text{mC}$ (D) $8.0\ \text{mC}$
E6. JEE Main · Numerical A coil of $50$ turns, each of area $0.040\ \text{m}^2$, has a resistance of $4.0\ \Omega$ and is connected to an external $6.0\ \Omega$ resistor. A uniform field perpendicular to the coil falls steadily from $0.80\ \text{T}$ to $0.20\ \text{T}$ in $0.30\ \text{s}$. Find the charge, in mC, that flows through the external resistor. Give the answer to the nearest integer.
Research question. When a magnet is dropped through a coil from different heights, how does the peak induced emf depend on its speed — and does the area under each emf pulse stay the same, as Faraday's law predicts?
Why it matters. Linear generators — a magnet sliding through a coil — power shake-to-charge torches, harvest energy from the bobbing of ocean-wave buoys in Portugal, Scotland and Australia, and are being tested in road surfaces and footwear. Seismometers and the pick-ups of electric guitars work the same way in reverse: they turn a motion into an emf. Designing any of them starts from $\varepsilon=-N\,d\Phi_B/dt$.
What to do.
- Wind a coil of a few hundred turns of thin enamelled wire on a plastic tube wide enough for a small strong magnet to fall through freely.
- Connect the coil to a data logger, an oscilloscope, or a laptop's microphone input through a simple voltage divider (free sound-recording software then shows the emf against time).
- Drop the magnet through the coil from heights of $5$, $10$, $20$, $40$ and $80\ \text{cm}$ above it. Record the two emf pulses each time.
- For each drop, read the peak emf and estimate the area under each pulse (count squares or sum the samples). Compute the speed at the coil, $v=\sqrt{2gh}$.
- Plot the peak emf against $v$, and the pulse area against $v$.
Tools: Plastic tube, enamelled copper wire, a neodymium magnet, metre rule, data logger or oscilloscope (or a laptop with sound software), spreadsheet.
Hand in: Your two graphs with a line of best fit, a short explanation of why the second pulse is larger than the first and of opposite sign, and a comparison of the pulse areas with $N\Phi_\text{max}$.
Going further. Repeat with a copper or aluminium tube around the coil. What happens to the pulses, and why? (The answer leads straight into eddy currents, Section 14.2.)
🧪 Self-check quiz
Q1. One weber is equal to
Q2. The minus sign in Faraday's law $\varepsilon=-N\,d\Phi_B/dt$ expresses
Q3. The charge that flows through a closed coil when the flux through it changes depends on
Q4. A straight conductor moves through a uniform magnetic field with its velocity parallel to the field. The emf induced between its ends is
Q5. A rod of length $l$ rotates with angular speed $\omega$ about one end in a plane perpendicular to a field $B$. If both $l$ and $\omega$ are doubled, the emf between its ends becomes