Chapter 3 · Laws of Motion

3.2 Free-Body Diagrams and Connected Bodies

Isolate each body, draw every force on it, write $\sum\mathbf{F}=m\mathbf{a}$ for each, and tie the equations together with the string's constraint. Lifts and accelerating cars are handled with one extra force: the pseudo force $-m\mathbf{a}_0$.

A crane lifts a container; a lift carries ten people up a tower; a goods train of fifty wagons is pulled by one locomotive; a rope over a pulley raises a bucket of cement while a counterweight comes down. In each case several bodies move together, pushing or pulling on each other through contact surfaces, ropes and couplings. The engineer needs every one of those internal forces — the tension in each coupling, the force on each pulley bracket, the load on the lift floor — because that is what breaks if the design is wrong.

Newton's laws (Section 3.1) are enough to find all of them. What you need is a method: isolate one body at a time, draw a free-body diagram showing every force on it, write the second law for it, and connect the bodies through constraint relations that say how their accelerations are linked by the strings. This section develops that method for blocks in contact, strings and rods, the Atwood machine and pulley systems, and then for observers who are themselves accelerating — a passenger in a lift or a car — using pseudo forces. Surfaces in this section are smooth; friction is added in Section 3.3.

Contact forces and free-body diagrams

Apart from gravity, every force in a mechanics problem is a contact force: the electrical push and pull between the atoms of two surfaces that touch, or between a body and a string attached to it. We split each contact force into a part perpendicular to the surfaces and a part along them.

📘 Definition 3.5 — Normal force, tension, ideal strings and pulleys

The normal force $N$ is the component of the contact force between two surfaces perpendicular to them. It always pushes (a surface cannot pull), and it takes whatever value is needed to stop one body passing into the other. If the calculated $N$ becomes zero, the bodies are just losing contact. (The component along the surfaces is friction — Section 3.3.)

Tension $T$ is the pull exerted by a taut string, rope, cable or chain on a body attached to it, directed along the string, away from the body. A string can pull but never push; a slack string has $T=0$.

An ideal string is massless and inextensible: the tension is the same at every point of it, and bodies tied to it move with the same speed along it. An ideal pulley is massless and frictionless: an ideal string passes over it with the same tension on both sides; only the direction of the pull changes.

Why a massless string has the same tension everywhere. Take a short piece of string of mass $\Delta m$ with tension $T_1$ pulling one end and $T_2$ the other. The second law gives $T_1-T_2=\Delta m\,a$. If $\Delta m=0$, then $T_1=T_2$ whatever the acceleration. For a heavy rope of mass $M$ and length $L$ pulled along a smooth floor by a force $F$ with a block of mass $m$ at the far end, the whole system has $a=\dfrac{F}{M+m}$, and the tension at a distance $x$ from the pulled end must accelerate everything beyond that point:

$$T(x)=\left(m+M\,\frac{L-x}{L}\right)a .$$

The tension falls steadily from $F$ at the pulled end to $ma$ at the block. A uniform rope hanging at rest has tension equal to the weight of the rope below each point — largest at the top.

📘 Definition 3.6 — Free-body diagram

A free-body diagram (FBD) is a sketch of one chosen body, shown on its own, with an arrow for every force that acts on it, each labelled with its symbol. Forces the body exerts on other bodies are not drawn, and neither is "$m\mathbf{a}$" — acceleration is the result of the forces, not one of them.

🧭 Problem-solving strategy — Newton's laws for one or many bodies
  1. Isolate each body and draw its FBD: weight $mg$ downwards; then one force for every contact — a normal force from each surface, a tension along each string, any applied push or pull.
  2. Choose axes for each body along and perpendicular to its acceleration (along an incline for a block on an incline, vertical for a hanging block). Different bodies may use different axes.
  3. Write $\sum F_x=ma_x$ and $\sum F_y=ma_y$ for each body. Use one symbol for each unknown tension and acceleration.
  4. Add the constraints: bodies tied by a taut ideal string have equal accelerations along it; bodies pressed together move together; for movable pulleys use the string-length method (next-but-one subsection).
  5. Solve, then check: a negative acceleration means you guessed the direction wrongly (repeat with the other direction if the sign matters); check a limiting case and that every $N$ and $T$ is positive.

Treating a system as one body. When several bodies move with the same acceleration, you may draw one FBD around all of them. The internal forces (contact forces between them, tensions in the strings joining them) cancel in pairs by the third law, so $\sum\mathbf{F}_\text{ext}=(m_1+m_2+\dots)\mathbf{a}$. This gives the acceleration in one line; then isolate a single body to find an internal force.

📐 Result 3.7 — Bodies pushed or pulled together

A horizontal force $F$ acts on a row of blocks $m_1,m_2,\dots,m_n$ in contact on a smooth horizontal floor (or joined by light horizontal strings). All move with

$$a=\frac{F}{m_1+m_2+\dots+m_n},$$

and the force between any two neighbouring blocks (contact force or string tension) equals (total mass beyond that joint) $\times\,a$ — the mass on the side away from the applied force.

✏️ Example 1 — Three crates pushed along a smooth floor
Crates of $2.0\ \text{kg}$, $3.0\ \text{kg}$ and $5.0\ \text{kg}$ stand in a row, touching, on a smooth floor. A horizontal force of $40\ \text{N}$ pushes the $2.0\ \text{kg}$ crate towards the others. (a) Find the acceleration. (b) Find the contact force between the $2.0\ \text{kg}$ and $3.0\ \text{kg}$ crates and between the $3.0\ \text{kg}$ and $5.0\ \text{kg}$ crates. (c) Repeat (b) if the same force pushes the $5.0\ \text{kg}$ crate from the other side instead.
(a) System One FBD round all three: the only horizontal external force is $40\ \text{N}$. $a=\dfrac{40}{10}=4.0\ \text{m/s}^2$.
(b) Isolate the $5.0\ \text{kg}$ crate: only $N_{35}$ pushes it, so $N_{35}=5.0\times4.0=20\ \text{N}$. Isolate the $2.0\ \text{kg}$ crate: $40-N_{23}=2.0\times4.0$, so $N_{23}=32\ \text{N}$.
(c) Now the "beyond" masses change: between $5.0$ and $3.0$: $(3.0+2.0)\times4.0=20\ \text{N}$; between $3.0$ and $2.0$: $2.0\times4.0=8.0\ \text{N}$.
Check Middle crate in (b): net force $32-20=12\ \text{N}=3.0\times4.0$ ✓. The acceleration is the same either way; the contact forces are not — they are largest next to the push.

Blocks of $1.0\ \text{kg}$ and $4.0\ \text{kg}$ touch on a smooth floor. A horizontal $10\ \text{N}$ force pushes the $1.0\ \text{kg}$ block against the $4.0\ \text{kg}$ one. The contact force between them is

Connected bodies: strings, pulleys and the Atwood machine

The simplest pulley problem is the Atwood machine: two masses hanging on either side of an ideal pulley, joined by an ideal string. It was built in 1784 to "slow down gravity" so that uniformly accelerated motion could be timed by eye, and it is still the cleanest test of the method.

Let $m_1\gt m_2$, so $m_1$ moves down and $m_2$ up with the same acceleration $a$ (the string is inextensible). FBD of $m_1$: weight $m_1g$ down, tension $T$ up. FBD of $m_2$: weight $m_2g$ down, tension $T$ up. Taking each body's direction of motion as positive,

$$m_1g-T=m_1a,\qquad T-m_2g=m_2a .$$

Adding eliminates $T$: $(m_1-m_2)g=(m_1+m_2)a$. Substituting back gives the tension.

📐 Result 3.8 — The Atwood machine and the table pulley

For two masses $m_1\gt m_2$ on an ideal string over an ideal fixed pulley:

$$a=\frac{(m_1-m_2)\,g}{m_1+m_2},\qquad T=\frac{2m_1m_2\,g}{m_1+m_2}.$$

The tension lies between $m_2g$ and $m_1g$, and the force on the pulley's support is $2T$, which is less than the total weight $(m_1+m_2)g$ while the masses accelerate.

For a block $m_1$ on a smooth horizontal table pulled by a string that passes over a pulley at the edge to a hanging mass $m_2$:

$$a=\frac{m_2\,g}{m_1+m_2},\qquad T=\frac{m_1m_2\,g}{m_1+m_2}.$$

The pattern behind both formulas is worth remembering: $a$ = (net driving force along the string) / (total mass moving). For a block $m_1$ on a smooth incline of angle $\theta$ tied over a pulley at the top to a hanging $m_2$, the driving force is $m_2g-m_1g\sin\theta$ (if positive, $m_2$ goes down), so $a=\dfrac{(m_2-m_1\sin\theta)g}{m_1+m_2}$. The tension then follows from either body's own equation.

✏️ Example 2 — An Atwood machine
Masses of $3.0\ \text{kg}$ and $5.0\ \text{kg}$ hang from the ends of a light string over a light frictionless pulley and are released from rest. Find (a) the acceleration, (b) the tension, (c) the force on the hook holding the pulley, and (d) the distance each mass moves in the first $2.0\ \text{s}$.
Find (a) and (b) yourself before you open the solution:
(a) $a=\dfrac{(5.0-3.0)(9.8)}{8.0}=2.45\ \text{m/s}^2$; the $5.0\ \text{kg}$ mass goes down.
(b) From the $3.0\ \text{kg}$ mass: $T=3.0(9.8+2.45)=36.75\ \text{N}\approx36.8\ \text{N}$. (Formula: $\dfrac{2(3.0)(5.0)(9.8)}{8.0}$, the same.)
(c) The string pulls down on the pulley on both sides: $2T=73.5\ \text{N}$ — less than the total weight $78.4\ \text{N}$.
(d) $s=\tfrac12at^2=\tfrac12(2.45)(2.0)^2=4.9\ \text{m}$ (one up, one down).
Check $5.0\ \text{kg}$ mass: $49-36.75=12.25=5.0\times2.45$ ✓. Equal masses would give $a=0$, $T=mg$; a very light $m_2$ gives $a\to g$, $T\to2m_2g\to0$ ✓.

A $4.0\ \text{kg}$ block on a smooth table is tied over the edge pulley to a hanging $3.0\ \text{kg}$ block. Once released, the tension in the string is

Choose "table and hanging mass", $m_1=4.0\ \text{kg}$, $m_2=3.0\ \text{kg}$ and read: $a=4.2\ \text{m/s}^2$, $T=16.8\ \text{N}$, weight $m_2g=29.4\ \text{N}$, "m₂ moves down". The tension is what accelerates the table block, $T=m_1a=4.0\times4.2$; the hanging block accelerates downwards, so the string must pull it with less than its weight: $29.4-16.8=12.6=3.0\times4.2$. Tension equals $m_2g$ only if nothing accelerates.
Interactive 1 — Pulley Lab: Free-Body Diagrams That Move

Choose a set-up — an Atwood machine, a block on a smooth table, or a block on a smooth incline — and set the masses (and the angle). The forces on each block are drawn to scale: weight (black), tension (purple) and normal force (green). Press Play to release the system from rest. Notice that the tension is always the same on both sides of the pulley, and that it is not equal to the weight of the hanging block unless nothing accelerates.

4.0 kg3.0 kg30°
acceleration $a$—
tension $T$—
weight $m_2g$—
motion—
✏️ Example 3 — A block on an incline pulled by a hanging mass
A $4.0\ \text{kg}$ block A rests on a smooth incline of $30^\circ$. A light string tied to A runs parallel to the incline, over a light pulley at the top, to a hanging $3.0\ \text{kg}$ block B. The system is released from rest. Find the acceleration, the tension, and the speed of B after it has fallen $1.0\ \text{m}$.
Find the tension before you open the solution:
Direction Pull of B: $m_Bg=29.4\ \text{N}$. Component of A's weight down the slope: $m_Ag\sin30^\circ=19.6\ \text{N}$. B wins, so B goes down and A up the slope.
Equations B: $29.4-T=3.0a$. A (along the slope, up positive): $T-19.6=4.0a$. (Perpendicular to the slope, $N=m_Ag\cos30^\circ=33.9\ \text{N}$; it does no work and drops out.)
Solve Adding: $9.8=7.0a$, $a=1.4\ \text{m/s}^2$. Then $T=3.0(9.8-1.4)=25.2\ \text{N}$.
Speed $v=\sqrt{2as}=\sqrt{2(1.4)(1.0)}=1.67\ \text{m/s}$.
Check A: $25.2-19.6=5.6=4.0\times1.4$ ✓. This is the default set-up of Interactive 1 — try it there.

An Atwood machine carries $2.0\ \text{kg}$ and $6.0\ \text{kg}$ masses ($g=10\ \text{m/s}^2$). While they move, the tension in the string is

Pulley systems and constraint relations

When every pulley is fixed, the bodies on a single string all move with the same speed along it. A movable pulley — one that hangs in a loop of the string and moves with its load — changes that. If the string has two strands supporting the pulley, pulling the free end through $1\ \text{m}$ shortens each strand by only $\tfrac12\ \text{m}$, so the load rises half as far, half as fast, with half the acceleration. In return, each strand needs carry only half the load: a movable pulley trades distance for force.

📘 Definition 3.7 — Constraint relation

A constraint relation is an equation linking the positions — and so the velocities and accelerations — of bodies that are connected by inextensible strings (or rigid rods, or surfaces in contact). For an ideal string it comes from the fact that its total length is constant.

🧭 Problem-solving strategy — The string-length method
  1. Measure the position of each moving body or pulley from a fixed reference (a fixed pulley, the ceiling), with a chosen positive direction for each.
  2. Write the length of each string as the sum of its straight segments in terms of these positions (the bits wrapped round pulleys are constant and can be dropped).
  3. Set $L=\text{constant}$ and differentiate twice: $\dfrac{dL}{dt}=0$ gives the velocity relation, $\dfrac{d^2L}{dt^2}=0$ the acceleration relation.
  4. Use that relation with the second-law equations. For a light movable pulley the net force must be zero (mass $\times$ acceleration $=0$), so the tensions on it balance: two strands of tension $T$ pull up with $2T$.

For example, suppose block A slides on a table, its string runs over a fixed pulley at the edge, down and under a movable pulley P, and up to a hook on the ceiling, while block B hangs from P. Measure A's distance $x_A$ from the fixed pulley and P's depth $y_P$ below the ceiling. The string length is $x_A+2y_P+\text{constant}$. Constant length gives $\Delta x_A=-2\,\Delta y_P$: if A moves towards the pulley by $2\ \text{cm}$, P and B descend $1\ \text{cm}$. In magnitude, $a_A=2a_B$, and the tension that pulls A is half the force holding up B.

✏️ Example 4 — A table block and a movable pulley
In the arrangement just described, block A ($4.0\ \text{kg}$) is on a smooth horizontal table and block B ($6.0\ \text{kg}$) hangs from the light movable pulley. All strings are light and the strands at P are vertical. The system is released from rest. Find the accelerations of A and B and the tension in the string.
Find the acceleration of A before you open the solution:
Constraint From $x_A+2y_P=\text{constant}$: $a_A=2a_B$ (A towards the pulley while B goes down). Let $a_B=a$, so $a_A=2a$.
FBDs A: tension $T$ towards the pulley, so $T=m_Aa_A=4.0(2a)=8.0a$. B with P: weight $m_Bg$ down, two strands $2T$ up, so $m_Bg-2T=m_Ba$.
Solve $6.0(9.8)-16a=6.0a$, so $58.8=22a$ and $a_B=2.67\ \text{m/s}^2$ downward; $a_A=5.35\ \text{m/s}^2$ towards the pulley.
Tension $T=8.0\times2.673=21.4\ \text{N}$.
Check B: $58.8-2(21.38)=16.0=6.0\times2.67$ ✓. Shortcut form: $a_B=\dfrac{m_Bg}{m_B+4m_A}$ — the table block counts four times because it moves twice as far and is pulled with half the force.

A load hangs from a light movable pulley supported by two vertical strands of one string; one end is tied to the ceiling. The free end is pulled upwards with an acceleration of $4.0\ \text{m/s}^2$. The load accelerates upwards at

Accelerating frames: lifts and pseudo forces

Stand on a bathroom scale in a lift. As the lift starts upwards the reading jumps; as it slows near the top the reading dips; if the cable broke it would read zero. The scale reads the normal force $N$ it exerts on you — that is what you feel as your "weight". Your true weight $mg$ never changes.

📐 Result 3.9 — Apparent weight in a lift

A person of mass $m$ stands on a scale in a lift whose acceleration is $a$ upwards (take $a$ negative if the acceleration is downwards). In the ground frame, $N-mg=ma$, so the scale reads the apparent weight

$$N=m(g+a).$$

Only the acceleration matters, not the velocity: moving up or down at constant speed, $N=mg$. Speeding up going up, or slowing down going down ($a$ up): $N\gt mg$. Speeding up going down, or slowing down going up ($a$ down): $N\lt mg$. In free fall ($a=-g$), $N=0$ — weightlessness. The same rule gives the tension in a lift cable, $T=(M+m)(g+a)$, and the reading of a spring balance hanging in the lift.

✏️ Example 5 — A ride on a bathroom scale
A $50\ \text{kg}$ student stands on a scale in a lift. Find the scale reading (in newtons, and in "kg" as a scale calibrated in kilograms would show) when the lift (a) moves up with acceleration $2.0\ \text{m/s}^2$, (b) moves up at a steady $3.0\ \text{m/s}$, (c) moves up but slows down at $2.0\ \text{m/s}^2$, (d) falls freely after its cable snaps.
(a) $a=+2.0$: $N=50(9.8+2.0)=590\ \text{N}$, shown as $\dfrac{590}{9.8}=60.2\ \text{kg}$.
(b) $a=0$: $N=490\ \text{N}$, $50.0\ \text{kg}$ — the steady speed is irrelevant.
(c) Moving up but slowing: acceleration is downward, $a=-2.0$: $N=50(9.8-2.0)=390\ \text{N}$, $39.8\ \text{kg}$.
(d) $a=-g$: $N=0$. Student and scale fall together; the scale reads zero.
Check The direction of the velocity never entered — only the direction of the acceleration. Interactive 2 runs exactly this kind of ride.

A $60\ \text{kg}$ passenger rides with the lift acceleration set to $2.0\ \text{m/s}^2$. On the way down, while the lift is slowing to a stop at the ground floor, the scale reads

Set mass $=60\ \text{kg}$, lift acceleration $=2.0\ \text{m/s}^2$, free fall "no", press Play and watch the phase "slowing down, going down" (between $t=13$ and $15\ \text{s}$): acceleration $2\ \text{m/s}^2$ (up +), scale reading $708\ \text{N}$, scale shows $72.2\ \text{kg}$, above the dashed $mg=588\ \text{N}$. Slowing a downward motion needs an upward acceleration, so $N=m(g+a)=60(9.8+2.0)=708\ \text{N}$. The $468\ \text{N}$ reading appears earlier, while the lift speeds up going down.
Interactive 2 — A Lift Ride on a Bathroom Scale

A passenger stands on a scale in a lift that goes up and then comes down again: speed up, steady, slow down, pause — each way. Set the passenger's mass and how hard the lift accelerates; tick the free-fall option to cut the cable on the way down (an emergency brake catches it). The graph traces the scale reading $N=m(g+a)$ against time with the true weight $mg$ dashed. Inside the cabin the forces are drawn in the lift's own frame: $N$ (green), $mg$ (black) and the pseudo force $-m\mathbf{a}$ (amber, dashed), which balance exactly.

60 kg2.0 m/s²
phase—
acceleration (up +)—
scale reading $N$—
scale shows—

Pseudo forces. We solved Example 5 in the ground frame, which is inertial. The student, however, sees herself at rest in the lift, yet the forces $N$ and $mg$ on her are unequal. Newton's laws fail in the lift's frame because that frame is accelerating. They can be rescued by adding one fictitious force to every body.

📘 Definition 3.8 — Non-inertial frame and pseudo force

A frame of reference that accelerates relative to an inertial frame is a non-inertial frame. To use Newton's second law in a frame moving with acceleration $\mathbf{a}_0$ (without rotation), add to every body of mass $m$ a pseudo force

$$\mathbf{F}_\text{pseudo}=-m\,\mathbf{a}_0,$$

directed opposite to the frame's acceleration. It is not exerted by any body, has no third-law partner and does not appear in the ground frame; it simply accounts for the acceleration of the observer.

📐 Result 3.10 — Newton's second law in an accelerating frame

In a frame with acceleration $\mathbf{a}_0$, the acceleration $\mathbf{a}_\text{rel}$ of a body measured in that frame satisfies

$$\sum\mathbf{F}_\text{real}-m\mathbf{a}_0=m\,\mathbf{a}_\text{rel}.$$

A body at rest in the frame ($\mathbf{a}_\text{rel}=\mathbf{0}$) is in equilibrium under the real forces plus the pseudo force. Two important cases: a bob hanging in a vehicle with horizontal acceleration $a_0$ settles with its string at angle $\theta$ to the vertical where $\tan\theta=\dfrac{a_0}{g}$ (tilted backwards) and $T=m\sqrt{g^2+a_0^2}$; inside a lift with upward acceleration $a_0$, everything behaves as if gravity were $g_\text{eff}=g+a_0$.

Use either frame — never a mixture. The ground-frame method is always correct; the pseudo-force method often turns a dynamics problem into an equilibrium problem, which is quicker. In the lift frame, the student is at rest under $N$ up, $mg$ down and the pseudo force $ma_0$ down: $N=m(g+a_0)$, exactly as before.

✏️ Example 6 — A pendulum in a car and a block on a wedge
(a) A $0.20\ \text{kg}$ bob hangs by a string from the roof of a car accelerating at $3.0\ \text{m/s}^2$ on a straight level road. Find the angle the string makes with the vertical and its tension. (b) A block rests on the smooth face of a wedge inclined at $37^\circ$. With what horizontal acceleration must the wedge be pushed so that the block stays at rest relative to it? (Take $\tan37^\circ=0.75$, $\cos37^\circ=0.80$.) How large is the normal force then, compared with the block's weight?
(a) Car frame The bob is at rest under $mg$ down, the pseudo force $ma_0$ backwards and $T$ along the string. Equilibrium: $T\sin\theta=ma_0$, $T\cos\theta=mg$, so $\tan\theta=\dfrac{3.0}{9.8}$ and $\theta=17.0^\circ$, tilted towards the back.
(a) Tension $T=m\sqrt{g^2+a_0^2}=0.20\sqrt{96.04+9.0}=2.05\ \text{N}$ (more than $mg=1.96\ \text{N}$).
(b) Wedge frame Push the wedge towards the incline face so that the pseudo force $ma_0$ on the block points away from the face, horizontally. Along the incline, the pseudo force's component $ma_0\cos37^\circ$ (up the slope) must balance $mg\sin37^\circ$ (down the slope): $a_0=g\tan37^\circ=9.8\times0.75=7.35\ \text{m/s}^2$.
(b) Normal Perpendicular: $N=mg\cos37^\circ+ma_0\sin37^\circ=\dfrac{mg}{\cos37^\circ}=1.25\,mg$ — the block presses harder than its weight.
Check Ground frame for (b): $N\cos37^\circ=mg$ and $N\sin37^\circ=ma_0$ give the same two answers, with no pseudo force — the horizontal component of $N$ is what accelerates the block.
⚠️ JEE Main traps

1. Setting tension equal to the hanging weight. $T=m_2g$ only if nothing accelerates. In an Atwood machine $m_2g\lt T\lt m_1g$; in the table set-up $T=\dfrac{m_1m_2g}{m_1+m_2}\lt m_2g$.

2. Writing $N=mg$ by habit. Find $N$ from the perpendicular equation each time: on an incline $N=mg\cos\theta$, in a lift $N=m(g+a)$, on an accelerated wedge $N=mg/\cos\theta$.

3. Velocity instead of acceleration in lift problems. "Moving down and slowing down" means the acceleration is upward, so the reading is more than $mg$.

4. Wrong constraint for a movable pulley. Two strands supporting the pulley: the load moves half as far as the free end ($a_\text{load}=\tfrac12a_\text{end}$) and the pull on the load is $2T$. Derive it from the string length rather than guessing.

5. Mixing frames. Add the pseudo force $-m\mathbf{a}_0$ only when you write the equations in the accelerating frame, and then add it to every body; never add it in the ground frame. Force on a fixed pulley's support is the vector sum of the two tensions ($2T$ only if both strands are parallel).

A lift is moving upwards but slowing down as it nears the top floor. Compared with your true weight $mg$, a bathroom scale under you reads

Exercises

Take $g=9.8\ \text{m/s}^2$ unless told otherwise. All surfaces are smooth; strings and pulleys are light and frictionless.

I
Normal force, tension and free-body diagrams.
  • 1 A $1.0\ \text{kg}$ ball hangs at rest by a string against a smooth vertical wall, with the string at $30^\circ$ to the wall. Draw its FBD and find the tension and the normal force from the wall.
  • 2 An $8.0\ \text{kg}$ box on a smooth floor is pushed with $30\ \text{N}$ directed $30^\circ$ below the horizontal. Find the normal force and the acceleration.
  • 3 A $2.0\ \text{kg}$ block hangs from the ceiling by string 1; a $3.0\ \text{kg}$ block hangs from the first by string 2. Find both tensions at rest, and again when the ceiling (a lift roof) accelerates upwards at $2.0\ \text{m/s}^2$.
  • 4 A uniform rope of mass $1.0\ \text{kg}$ and length $2.0\ \text{m}$ hangs vertically from a hook. Find the tension at its midpoint and at the top.
  • 5 A uniform rope of mass $2.0\ \text{kg}$ pulls an $8.0\ \text{kg}$ block on a smooth floor; a $50\ \text{N}$ horizontal force acts on the free end of the rope. Find the acceleration and the tension at the block and at the middle of the rope.
  • 6 A $5.0\ \text{kg}$ block is released on a smooth incline of $37^\circ$. Taking $\sin37^\circ=0.60$, find the normal force and the acceleration.
  • 7 A $3.0\ \text{kg}$ block on a smooth floor is pulled by a string at $53^\circ$ above the horizontal with tension $20\ \text{N}$ ($\sin53^\circ=0.80$). Find $N$ and the acceleration. What tension would just lift the block off the floor?
1 Forces: $mg$ down, $T$ along the string, $N$ horizontal from the wall. $T\cos30^\circ=mg$: $T=11.3\ \text{N}$; $N=T\sin30^\circ=mg\tan30^\circ=5.66\ \text{N}$.
2 $N=78.4+30\sin30^\circ=93.4\ \text{N}$; $a=\dfrac{30\cos30^\circ}{8.0}=3.25\ \text{m/s}^2$.
3 At rest: $T_1=5.0g=49\ \text{N}$, $T_2=3.0g=29.4\ \text{N}$. Accelerating: $T_1=5.0(11.8)=59\ \text{N}$, $T_2=3.0(11.8)=35.4\ \text{N}$.
4 Midpoint supports half the rope: $T=0.50\times9.8=4.9\ \text{N}$; top: $9.8\ \text{N}$.
5 $a=\dfrac{50}{10}=5.0\ \text{m/s}^2$; at the block $T=8.0\times5.0=40\ \text{N}$; at the middle $T=(8.0+1.0)\times5.0=45\ \text{N}$.
6 $N=49\times0.80=39.2\ \text{N}$; $a=9.8\times0.60=5.88\ \text{m/s}^2$ down the slope.
7 $N=29.4-20(0.80)=13.4\ \text{N}$; $a=\dfrac{20(0.60)}{3.0}=4.0\ \text{m/s}^2$. Lift-off when $T\sin53^\circ=mg$: $T=\dfrac{29.4}{0.80}=36.75\ \text{N}\approx36.8\ \text{N}$.
II
Connected bodies.
  • 1 Blocks of $4.0\ \text{kg}$ and $6.0\ \text{kg}$ touch on a smooth floor. A $20\ \text{N}$ horizontal force pushes the $4.0\ \text{kg}$ block. Find the contact force. What is it if the force pushes the $6.0\ \text{kg}$ block instead?
  • 2 Blocks of $2.0\ \text{kg}$ and $3.0\ \text{kg}$ are joined by a light string on a smooth floor. A $15\ \text{N}$ force pulls the $3.0\ \text{kg}$ block away from the other. Find the acceleration and the tension.
  • 3 A locomotive exerts a net horizontal pull of $40\,000\ \text{N}$ on a train of five identical $20\,000\ \text{kg}$ coaches. Find the acceleration and the tension in the coupling between the 1st and 2nd coaches and between the 4th and 5th.
  • 4 Masses of $2.0\ \text{kg}$ and $3.0\ \text{kg}$ hang over a pulley (Atwood machine). Find the acceleration and the tension.
  • 5 In an Atwood machine the acceleration is $g/4$. Find the ratio of the larger to the smaller mass.
  • 6 A $6.0\ \text{kg}$ block on a smooth table is joined by a string over a pulley at the edge to a hanging $2.0\ \text{kg}$ block. Find the acceleration and the tension.
  • 7 A smooth wedge has faces at $60^\circ$ and $30^\circ$ to the horizontal meeting at a pulley at the top. A $2.0\ \text{kg}$ block on the $60^\circ$ face is tied over the pulley to a $3.0\ \text{kg}$ block on the $30^\circ$ face. Which way do they move? Find the acceleration and the tension.
  • 8 A $5.0\ \text{kg}$ block on a smooth $30^\circ$ incline is tied over a pulley at the top to a hanging $1.0\ \text{kg}$ block. Which way do they move? Find the acceleration and the tension.
1 $a=2.0\ \text{m/s}^2$; contact $=6.0\times2.0=12\ \text{N}$; pushed from the other side, $4.0\times2.0=8.0\ \text{N}$.
2 $a=\dfrac{15}{5.0}=3.0\ \text{m/s}^2$; $T=2.0\times3.0=6.0\ \text{N}$.
3 $a=\dfrac{40\,000}{100\,000}=0.40\ \text{m/s}^2$; 1st–2nd coupling pulls four coaches: $32\,000\ \text{N}$; 4th–5th pulls one: $8000\ \text{N}$.
4 $a=\dfrac{1.0\times9.8}{5.0}=1.96\ \text{m/s}^2$; $T=\dfrac{2(2.0)(3.0)(9.8)}{5.0}=23.5\ \text{N}$.
5 $\dfrac{m_1-m_2}{m_1+m_2}=\dfrac14$ gives $4m_1-4m_2=m_1+m_2$, so $\dfrac{m_1}{m_2}=\dfrac53$.
6 $a=\dfrac{2.0\times9.8}{8.0}=2.45\ \text{m/s}^2$; $T=6.0\times2.45=14.7\ \text{N}$.
7 Down-slope pulls: $2.0(9.8)\sin60^\circ=17.0\ \text{N}$ versus $3.0(9.8)\sin30^\circ=14.7\ \text{N}$; the $2.0\ \text{kg}$ block slides down. $a=\dfrac{2.27}{5.0}=0.455\ \text{m/s}^2$; $T=14.7+3.0(0.455)=16.1\ \text{N}$.
8 $5.0(9.8)(0.5)=24.5\ \text{N}$ down the slope beats $9.8\ \text{N}$: the $5.0\ \text{kg}$ block slides down, the $1.0\ \text{kg}$ rises. $a=\dfrac{14.7}{6.0}=2.45\ \text{m/s}^2$; $T=1.0(9.8+2.45)=12.25\ \text{N}\approx12.2\ \text{N}$.
III
Pulley systems and constraints.
  • 1 A $20\ \text{kg}$ load hangs from a light movable pulley. One end of the string is tied to the ceiling and the other is pulled vertically upwards. What force holds the load at rest? If the free end is pulled up $1.0\ \text{m}$, how far does the load rise?
  • 2 In part 1, what force raises the load with an acceleration of $1.0\ \text{m/s}^2$? What is the acceleration of the free end of the string?
  • 3 In the arrangement of Example 4, A has mass $1.0\ \text{kg}$ and B has mass $2.0\ \text{kg}$. Find $a_A$, $a_B$ and the tension.
  • 4 One end of a string is fixed to the ceiling; the string passes down under a movable pulley carrying a load, up over a fixed pulley, and its free end is pulled down at a steady $0.60\ \text{m/s}$. How fast does the load rise?
  • 5 In an ideal pulley block, an $80\ \text{kg}$ load is supported by four strands of one string. What effort holds it at rest, and how much string must be pulled to lift the load by $1.0\ \text{m}$?
  • 6 In Exercise II.6 the string leaves the pulley horizontally on one side and vertically on the other. Find the magnitude and direction of the force the string exerts on the pulley.
  • 7 The pulley of the Atwood machine in Exercise II.4 hangs from a spring balance. What does the balance read while the masses move? Compare it with the total weight.
1 $2T=mg$: $T=\dfrac{20\times9.8}{2}=98\ \text{N}$. String length $2y+\text{const}$: the load rises $0.50\ \text{m}$.
2 $2T-mg=ma$: $T=\dfrac{20(9.8+1.0)}{2}=108\ \text{N}$; the free end accelerates at $2.0\ \text{m/s}^2$.
3 $a_B=\dfrac{m_Bg}{m_B+4m_A}=\dfrac{19.6}{6.0}=3.27\ \text{m/s}^2$; $a_A=6.53\ \text{m/s}^2$; $T=m_Aa_A=6.53\ \text{N}$.
4 Two strands support the load, so it rises at half the speed of the free end: $0.30\ \text{m/s}$.
5 $4T=mg$: $T=\dfrac{784}{4}=196\ \text{N}$; each strand shortens by $1.0\ \text{m}$, so $4.0\ \text{m}$ of string is pulled.
6 Two perpendicular pulls of $14.7\ \text{N}$: resultant $\sqrt2\times14.7=20.8\ \text{N}$, at $45^\circ$ below the horizontal, towards the table.
7 $2T=2\times23.52=47.0\ \text{N}$, less than the total weight $49\ \text{N}$ (the system's centre of mass is accelerating downwards).
IV
Lifts and pseudo forces.
  • 1 A $60\ \text{kg}$ man stands in a lift accelerating upwards at $1.5\ \text{m/s}^2$. Find the normal force on him.
  • 2 Find the normal force when the lift moves down at a steady $3.0\ \text{m/s}$.
  • 3 Find the normal force when the lift is moving down and slowing at $2.0\ \text{m/s}^2$.
  • 4 Find the normal force when the lift accelerates downwards at $2.0\ \text{m/s}^2$. In the same lift, what does a spring balance read for a hanging $1.0\ \text{kg}$ mass?
  • 5 A $800\ \text{kg}$ lift carries passengers of total mass $300\ \text{kg}$. The cable can safely take $15\,000\ \text{N}$. Find the greatest safe upward acceleration.
  • 6 A pendulum hangs from the roof of a bus accelerating at $2.0\ \text{m/s}^2$. Find the angle of the string with the vertical, and say which way it tilts.
  • 7 A smooth $30^\circ$ incline is fixed inside a trolley. With what horizontal acceleration must the trolley move for a block on the incline to stay at rest relative to it?
  • 8 A lift is accelerating upwards at $2.2\ \text{m/s}^2$. A coin is dropped from $1.5\ \text{m}$ above its floor. How long does the coin take to reach the floor?
  • 9 A $70\ \text{kg}$ man on a scale (calibrated in kg) in a lift sees it read $84\ \text{kg}$. Find the lift's acceleration. Can you tell whether the lift is moving up or down?
1 $N=60(9.8+1.5)=678\ \text{N}$.
2 $a=0$: $N=588\ \text{N}$.
3 Acceleration is upward: $N=60(9.8+2.0)=708\ \text{N}$.
4 $N=60(9.8-2.0)=468\ \text{N}$; balance reads $1.0(7.8)=7.8\ \text{N}$ (about $0.80\ \text{kg}$ on a kg scale).
5 $T=(M+m)(g+a)$: $a=\dfrac{15\,000}{1100}-9.8=3.84\ \text{m/s}^2$.
6 $\tan\theta=\dfrac{2.0}{9.8}$: $\theta=11.5^\circ$, tilted towards the back of the bus.
7 $a_0=g\tan30^\circ=5.66\ \text{m/s}^2$, directed towards the side the incline faces (so the pseudo force pushes the block up the slope).
8 In the lift frame $g_\text{eff}=9.8+2.2=12\ \text{m/s}^2$: $t=\sqrt{\dfrac{2(1.5)}{12}}=0.50\ \text{s}$.
9 $m(g+a)=84g$ gives $a=g\left(\tfrac{84}{70}-1\right)=0.20g=1.96\ \text{m/s}^2$ upward. No: it may be speeding up going up or slowing down going down — only the acceleration is known.
🎯 Exam corner JEE Main · MCQJEE Main · Numerical

E1. JEE Main · MCQ Blocks of $2\ \text{kg}$ and $4\ \text{kg}$ are in contact on a smooth horizontal floor. A horizontal force of $12\ \text{N}$ is applied to the $2\ \text{kg}$ block, pushing it against the $4\ \text{kg}$ block. The contact force between them is (A) $4\ \text{N}$ (B) $6\ \text{N}$ (C) $8\ \text{N}$ (D) $12\ \text{N}$

System $a=\dfrac{12}{6}=2\ \text{m/s}^2$.
Isolate The $4\ \text{kg}$ block is pushed only by the contact force: $N=4\times2=8\ \text{N}$.
Answer (C). (A) is the answer if the force were applied to the $4\ \text{kg}$ block.
⏱ Shortcut Contact force $=F\times\dfrac{\text{mass beyond the joint}}{\text{total mass}}=12\times\dfrac46$.

E2. JEE Main · Numerical Two masses of $3\ \text{kg}$ and $7\ \text{kg}$ are connected by a light inextensible string passing over a light frictionless pulley. Taking $g=10\ \text{m/s}^2$, find the tension in the string (in N) while they move. Give the answer to the nearest integer.

Acceleration $a=\dfrac{(7-3)(10)}{10}=4\ \text{m/s}^2$.
Tension $3\ \text{kg}$ mass: $T=3(10+4)=42\ \text{N}$.
Answer $42$.
⏱ Shortcut $T=\dfrac{2m_1m_2g}{m_1+m_2}=\dfrac{2(21)(10)}{10}$ — the harmonic-mean form, always between the two weights ($30$ and $70\ \text{N}$).

E3. JEE Main · MCQ A $60\ \text{kg}$ person stands on a weighing machine in a lift that is moving downwards and slowing down at $2\ \text{m/s}^2$. Taking $g=10\ \text{m/s}^2$, the machine reads (A) $720\ \text{N}$ (B) $480\ \text{N}$ (C) $600\ \text{N}$ (D) $840\ \text{N}$

Direction Moving down and slowing: the acceleration is upward, $a=+2\ \text{m/s}^2$.
Reading $N=m(g+a)=60(12)=720\ \text{N}$.
Answer (A). (B) is the trap of taking "downwards" as the direction of acceleration.

E4. JEE Main · Numerical A $4\ \text{kg}$ block on a smooth incline of $30^\circ$ is connected by a light string, parallel to the incline and passing over a light pulley at the top, to a hanging $6\ \text{kg}$ block. Taking $g=10\ \text{m/s}^2$, find the tension in the string (in N). Give the answer to the nearest integer.

Acceleration Driving force $60-4(10)\sin30^\circ=40\ \text{N}$; total mass $10\ \text{kg}$: $a=4\ \text{m/s}^2$, hanging block down.
Tension Hanging block: $T=6(10-4)=36\ \text{N}$. Check with the other block: $36-20=16=4\times4$ ✓.
Answer $36$.

E5. JEE Main · MCQ A small bob hangs by a light string from the roof of a train that is moving with a constant acceleration $a$ on a straight horizontal track. In equilibrium relative to the train, the string makes with the vertical an angle (A) $\tan^{-1}(g/a)$ (B) $\sin^{-1}(a/g)$ (C) $\cos^{-1}(a/g)$ (D) $\tan^{-1}(a/g)$, tilted towards the rear

Train frame Bob at rest under $mg$ down, pseudo force $ma$ backwards and $T$. $T\sin\theta=ma$, $T\cos\theta=mg$.
Divide $\tan\theta=\dfrac ag$.
Answer (D).
⏱ Shortcut The string lines up with the effective gravity $\mathbf{g}-\mathbf{a}$; limiting case $a=0$ must give $\theta=0$, which only (D) does.

E6. JEE Main · Numerical Block A of mass $2\ \text{kg}$ lies on a smooth horizontal table. A light string tied to A passes over a fixed pulley at the edge of the table, goes down and under a light movable pulley from which block B of mass $8\ \text{kg}$ hangs, and its other end is fixed to a support directly above. The strands at the movable pulley are vertical. Taking $g=10\ \text{m/s}^2$, find the acceleration of A (in $\text{m/s}^2$). Give the answer to the nearest integer.

Constraint String length $x_A+2y_B=\text{constant}$, so $a_A=2a_B$.
Equations A: $T=2(2a_B)=4a_B$. B: $80-2T=8a_B$, so $80=16a_B$ and $a_B=5\ \text{m/s}^2$.
Answer $a_A=2a_B=10$.
⏱ Shortcut $a_B=\dfrac{m_Bg}{m_B+4m_A}=\dfrac{80}{16}$. Don't stop at $a_B$ — the question asks for A.
🔬 Research–Teaching NexusResearch-tutored · optional, about 45 minutes

Research question. How large are the accelerations of real lifts — and do they stay within the comfort limits that lift engineers design for?

Why it matters. Lift designers in high-rise buildings from Mumbai to Dubai to Shanghai must move people quickly without making them uncomfortable. Passengers start to notice accelerations of about $1\ \text{m/s}^2$, and most international guidelines keep ordinary passenger lifts near or below $1.0$–$1.5\ \text{m/s}^2$; the rate of change of acceleration ("jerk") is limited too. Every smartphone contains an accelerometer that measures exactly the quantity the bathroom scale does: the apparent gravity $g+a$.

What to do.

  1. Install a free sensor app that logs the phone's accelerometer (vertical component, in $\text{m/s}^2$). Place the phone flat on the floor of a lift and record a full ride up several floors and back down.
  2. Read the steady value at rest — it should be close to $9.8\ \text{m/s}^2$ — then the peak values while starting and stopping. Subtract to get the lift's acceleration $a$ in each phase.
  3. Integrate: the area under the $a$–$t$ graph during start-up gives the cruising speed. Multiply by the cruising time and compare the total with the height of the floors climbed.
  4. Predict what a $60\ \text{kg}$ passenger's bathroom scale would read in each phase using $N=m(g+a)$.

Tools: Smartphone with a sensor-logging app, a lift (or a fast escalator for a gentler test), spreadsheet; optionally a bathroom scale to check the prediction directly.

Hand in: An annotated $a$–$t$ graph of one ride, a table of the start and stop accelerations with the predicted scale readings, and a comparison of your measured cruise speed and travel distance with the building's floor heights.

Going further. Compare two different lifts (an old one and a new one) or the same lift going up and going down. Which has the larger jerk? Explain why designers limit jerk as well as acceleration.

Instructor note: typical office lifts show $|a|\approx0.6$–$1.2\ \text{m/s}^2$ for $1$–$2\ \text{s}$ and cruise at $1$–$2.5\ \text{m/s}$; tall-building express lifts reach $5$–$10\ \text{m/s}$ but still accelerate gently over longer times. Phones may report $g+a$ or $a$ alone depending on the app ("linear acceleration" removes gravity) — a good discussion of what an accelerometer actually measures. Integration errors grow with time, so the distance check is only good to about $10$–$20\%$.

🧪 Self-check quiz

0/5 correct

Q1. A box of mass $m$ on a smooth floor is pulled by a rope at an angle $\theta$ above the horizontal with tension $T$. The normal force on the box is

Q2. In an Atwood machine with two equal masses, the masses are given a push so that one moves up and the other down. Afterwards they

Q3. A person standing on a weighing machine in a lift sees the reading drop to zero. The lift is

Q4. In a frame of reference moving with acceleration $\mathbf{a}_0$, Newton's second law can be used for a body of mass $m$ if we add a pseudo force equal to

Q5. A load hangs from a light movable pulley supported by two vertical strands of one string. If the free end of the string is pulled up with acceleration $a$, the load rises with acceleration