Chapter 7 · Properties of Solids and Liquids

7.2 Fluid Pressure and Buoyancy

In a fluid at rest the pressure depends only on depth, $p=p_0+\rho gh$. From that one result come barometers and manometers, the force on a dam, Pascal's law and the hydraulic lift — and Archimedes' buoyant force $\rho_\text{f}Vg$, which decides what floats and how deep.

A dam is built far thicker at its base than at its top. A diver's ears hurt a few metres below the surface of a swimming pool, while a mountaineer's crisp packet puffs up near the summit. A garage mechanic lifts a two-tonne car by pumping a small handle. A steel ship weighing fifty thousand tonnes floats, while a steel bolt sinks. A nurse measures blood pressure with the cuff at the level of the heart, not around the ankle. All of these are explained by how pressure behaves in a fluid that is at rest — the subject called hydrostatics.

The key fact is simple: in a fluid at rest, the pressure at a point is the same in every direction and grows steadily with depth, because each layer of fluid must hold up the weight of the fluid above it. In this section we define pressure, derive $p=p_0+\rho gh$, and use it on barometers, manometers, U-tubes and dam walls. We see what happens to fluid pressure when "gravity" changes — in an accelerating lift or a braking tanker — and then derive Pascal's law (the principle of every hydraulic machine) and Archimedes' principle (the principle of everything that floats). Section 7.1 met the bulk modulus; here we treat liquids as incompressible, which that section showed is an excellent approximation.

Pressure in a fluid at rest

📘 Definition 7.8 — Fluid and pressure

A fluid is a substance that can flow — a liquid or a gas. It has no shape of its own and, at rest, cannot sustain a tangential (shearing) force: any such force makes it flow. Therefore the force that a fluid at rest exerts on any surface in contact with it is normal to that surface.

If the normal force exerted by a fluid on a small area $\Delta A$ is $\Delta F$, the pressure at that point is

$$p=\lim_{\Delta A\to0}\frac{\Delta F}{\Delta A},\qquad\text{and for a uniform force }p=\frac{F}{A}.$$

Pressure is a scalar: at a point it has a size but no direction — the force it produces on a surface is always along the normal to that surface. SI unit: the pascal, $1\ \text{Pa}=1\ \text{N/m}^2$; dimensions $[\mathrm{M\,L^{-1}T^{-2}}]$. Other units in use: $1\ \text{bar}=10^5\ \text{Pa}$; $1\ \text{atm}=1.013\times10^5\ \text{Pa}=760\ \text{mm of mercury (mm Hg)}$; $1\ \text{torr}=1\ \text{mm Hg}=133\ \text{Pa}$.

Same in every direction. Take a tiny triangular wedge of fluid at rest. The fluid outside pushes normally on each of its faces, and the forces must balance (the wedge's weight becomes negligible as it shrinks, since weight scales as volume but the surface forces scale as area). Resolving the forces shows that the pressure on the sloping face equals the pressure on each of the other faces, whatever the angle of the slope. So at a point in a fluid at rest the pressure is the same in all directions — the fluid pushes sideways and upwards just as hard as downwards.

📘 Definition 7.9 — Density and relative density

The density of a substance is its mass per unit volume, $\rho=\dfrac{m}{V}$ (unit $\text{kg/m}^3$). The relative density (specific gravity) is the ratio of its density to the density of water at $4^\circ\text{C}$, $1.0\times10^3\ \text{kg/m}^3$; it is a pure number. Typical densities: water $1.0\times10^3$, sea water $1.03\times10^3$, mercury $13.6\times10^3$, ice $917$, air (at sea level, $20^\circ\text{C}$) $1.2\ \text{kg/m}^3$.

How pressure changes with depth. Consider a vertical cylinder of liquid of cross-section $A$ inside a liquid of density $\rho$ at rest, with its top at depth $h_1$ and its bottom at depth $h_2$. The sideways forces on its curved surface cancel. Vertically, three forces act: the push $p_1A$ of the liquid above, down; the push $p_2A$ of the liquid below, up; and the cylinder's weight $\rho A(h_2-h_1)g$, down. The cylinder is in equilibrium, so

$$p_2A=p_1A+\rho A(h_2-h_1)g\quad\Longrightarrow\quad p_2-p_1=\rho g(h_2-h_1).$$
📐 Result 7.5 — Pressure due to a fluid column

In a liquid of uniform density $\rho$ at rest, in a uniform gravitational field $g$, the pressure at depth $h$ below the free surface is

$$p=p_0+\rho gh ,$$

where $p_0$ is the pressure at the surface (the atmospheric pressure, for an open vessel). Consequences:

  • Pressure depends only on the depth, not on the shape or the width of the vessel, nor on how much liquid there is.
  • All points at the same depth in the same connected liquid at rest have the same pressure: horizontal planes are surfaces of equal pressure, and the free surface is horizontal.
  • The extra pressure $\rho gh$ is the weight of a column of liquid of height $h$ and unit cross-section.

Conditions: the fluid is at rest, incompressible (constant $\rho$) and in a uniform $g$. For a gas over large heights (the atmosphere) $\rho$ falls with height, and the formula holds only over small height differences.

The hydrostatic paradox. Three vessels with the same base area — one straight-sided, one flaring outwards, one narrowing upwards — are filled with water to the same depth. They hold very different amounts of water, yet the pressure on each base is the same, $p_0+\rho gh$, so the force of the water on each base is the same, $\rho ghA$. There is no contradiction: in the flared vessel the sloping walls carry part of the water's weight, and in the narrowing vessel the walls push down on the water, adding to the force on the base. Interactive 1 shows the base force and the weight side by side.

✏️ Example 1 — A diver and a submarine window
Take the density of sea water as $1030\ \text{kg/m}^3$ and atmospheric pressure as $1.013\times10^5\ \text{Pa}$. (a) Find the gauge pressure (pressure above atmospheric) and the absolute pressure on a diver $20\ \text{m}$ below the surface. Express the absolute pressure in atmospheres. (b) A research submarine at a depth of $200\ \text{m}$ has a circular window $30\ \text{cm}$ in diameter; the air inside is at atmospheric pressure. Find the net force of the water on the window.
(a) gauge $p-p_0=\rho gh=1030\times9.8\times20=2.02\times10^5\ \text{Pa}$.
(a) absolute $p=1.013\times10^5+2.02\times10^5=3.03\times10^5\ \text{Pa}$, almost exactly $3.0\ \text{atm}$: every $10\ \text{m}$ of sea water adds about one atmosphere.
(b) The atmosphere pushes on both faces of the window (on the sea side through the water, and directly on the inside), so only the gauge pressure produces a net force: $\rho gh=1030\times9.8\times200=2.02\times10^6\ \text{Pa}$. Area $\pi(0.15)^2=7.07\times10^{-2}\ \text{m}^2$; $F=2.02\times10^6\times7.07\times10^{-2}=1.4\times10^5\ \text{N}$ inwards — the weight of about $15$ tonnes.
Check Units: $\text{kg/m}^3\times\text{m/s}^2\times\text{m}=\text{kg}\,\text{m}^{-1}\text{s}^{-2}=\text{N/m}^2$ ✓. The window's diameter enters squared, so a window twice as wide needs to bear four times the force.

Three vessels have the same base area: A is straight-sided, B widens upwards, C narrows upwards. Each is filled with water to the same depth. The force exerted by the water on the base is

Atmospheric pressure, gauges and the effect of gravity

We live at the bottom of an ocean of air. The weight of the air above each square metre of the ground produces the atmospheric pressure, about $1.0\times10^5\ \text{Pa}$ at sea level. We do not feel it because the fluids in our bodies are at a similar pressure and push outwards equally.

📘 Definition 7.10 — Atmospheric, gauge and absolute pressure

Atmospheric pressure $p_0$ is the pressure of the air at a given place; its standard sea-level value is $1\ \text{atm}=1.013\times10^5\ \text{Pa}$. The absolute pressure $p$ is the actual pressure at a point. The gauge pressure is the excess over atmospheric pressure, $p-p_0$; it is what a tyre gauge or a blood-pressure meter reads. At depth $h$ in an open liquid, the gauge pressure is $\rho gh$.

The mercury barometer. Fill a long glass tube with mercury, close it with a finger, and invert it into a dish of mercury. The mercury falls until the column is about $76\ \text{cm}$ high, leaving a nearly perfect vacuum ($p\approx0$) at the top. The pressure at the level of the dish's surface is $p_0$ outside the tube and $\rho gh$ inside it, so

$$p_0=\rho_\text{Hg}\,g\,h .$$

With $\rho_\text{Hg}=13.6\times10^3\ \text{kg/m}^3$ and $h=0.760\ \text{m}$ this gives $1.013\times10^5\ \text{Pa}$. A water barometer would need a tube $13.6$ times taller, about $10.3\ \text{m}$; this is also the greatest height from which a suction pump can lift water.

The open-tube manometer. A U-tube contains a liquid of density $\rho_m$; one arm is connected to a vessel of gas, the other is open to the air. If the liquid stands $h$ higher in the open arm, the gas pressure exceeds atmospheric by $\rho_mgh$: the gauge pressure is read directly as a height. A U-tube with two immiscible liquids compares densities: at the level of the interface the pressures in the two arms are equal, so $\rho_1h_1=\rho_2h_2$ for the columns standing above that level.

✏️ Example 2 — Oil and water in a U-tube
A U-tube open at both ends contains water. Oil, which does not mix with water, is poured into the left arm until the oil column is $12.0\ \text{cm}$ long. The water in the right arm then stands $10.0\ \text{cm}$ above the level of the oil–water interface in the left arm. (a) Find the density of the oil. (b) Which free surface is higher, and by how much?
Find the density of the oil before you open the solution:
Equal level Draw a horizontal line through the interface. Below it the U-tube contains only water, a single connected liquid at rest, so the pressure on this line is the same in both arms.
Balance Left arm: $p_0+\rho_\text{oil}g(0.120)$. Right arm: $p_0+\rho_wg(0.100)$. Equating, $\rho_\text{oil}=1000\times\dfrac{10.0}{12.0}=833\ \text{kg/m}^3$.
(b) The oil surface is $12.0\ \text{cm}$ above the line and the water surface $10.0\ \text{cm}$, so the oil surface is higher by $2.0\ \text{cm}$ — the lighter liquid needs a taller column to balance.
Trap Equating pressures at the level of the free surfaces, or at any level that cuts through the oil, gives nonsense: the rule "same depth, same pressure" holds only within one connected liquid.

Force on a vertical wall. The water pressure on a dam or an aquarium wall grows from zero (gauge) at the surface to $\rho gH$ at the bottom, so the total force cannot be found as "pressure × area". For a vertical rectangular wall of width $w$ holding water of depth $H$, a horizontal strip of height $dy$ at depth $y$ has area $w\,dy$ and feels the force $\rho gy\,w\,dy$. Adding up the strips:

$$F=\int_0^H\rho g\,w\,y\,dy=\tfrac12\rho gwH^2 ,$$

which is the average gauge pressure $\tfrac12\rho gH$ times the area $wH$. Because the deeper strips push harder, the resultant acts below the middle of the wall.

📐 Result 7.6 — Force of a liquid on a vertical wall

A liquid of density $\rho$ at rest, of depth $H$, presses on a vertical rectangular wall of width $w$ (atmospheric pressure acts on both sides) with a horizontal force

$$F=\tfrac12\rho gwH^2 ,$$

acting at a height $H/3$ above the base (depth $2H/3$). Its moment about the base of the wall is $\tau=\dfrac{\rho gwH^3}{6}$. The force on the horizontal base of the vessel is $\rho gHA_\text{base}$.

✏️ Example 3 — The force on a dam
The vertical face of a small dam is $50\ \text{m}$ wide and holds back water $20\ \text{m}$ deep. (a) Find the total horizontal force of the water on the dam. (b) Find the moment of this force about the base of the dam. (c) If the water level rises to $30\ \text{m}$, by what factor do the force and the moment increase?
Find the total force on the dam before you open the solution:
(a) $F=\tfrac12\rho gwH^2=\tfrac12\times1000\times9.8\times50\times20^2=9.8\times10^7\ \text{N}$.
(b) The strip at depth $y$ is at height $H-y$ above the base: $\tau=\displaystyle\int_0^H\rho gwy\,(H-y)\,dy=\rho gw\left(\tfrac{H^3}{2}-\tfrac{H^3}{3}\right)=\dfrac{\rho gwH^3}{6}=\dfrac{1000\times9.8\times50\times8000}{6}=6.5\times10^8\ \text{N m}$.
Where $\tau/F=\dfrac{H}{3}=6.7\ \text{m}$ above the base: the resultant acts one third of the way up.
(c) $F\propto H^2$: $(30/20)^2=2.25$ times. $\tau\propto H^3$: $(1.5)^3=3.4$ times. A dam's tendency to topple grows with the cube of the water depth — which is why dams are so much thicker at the base.

The effect of gravity on fluid pressure. The pressure increase $\rho gh$ exists only because each layer must hold up the weight of the layers above it. Change the "effective gravity" and the pressure changes too. In a vessel accelerating upwards at $a$ (a lift starting to rise), the column of liquid above a point must be both supported and accelerated, so $\Delta p\cdot A-\rho Ahg=\rho Aha$, and the pressure difference becomes $\rho(g+a)h$. In a lift accelerating downwards at $a$ it is $\rho(g-a)h$; in free fall ($a=g$) the liquid is weightless and the pressure is the same throughout. In a tank accelerating horizontally at $a$, a horizontal column of liquid of length $\ell$ needs a net force $\rho A\ell a$, so the pressure must grow towards the back of the tank, and the free surface tilts.

📐 Result 7.7 — Pressure in an accelerating liquid

For a liquid that moves with its container as a rigid body with constant acceleration $\mathbf{a}$, the pressure behaves as in a liquid at rest in an effective gravity $\mathbf{g}_\text{eff}=\mathbf{g}-\mathbf{a}$:

  • vertical acceleration $a$ upwards: $p=p_0+\rho(g+a)h$; downwards: $p=p_0+\rho(g-a)h$; free fall: $p=p_0$ throughout;
  • horizontal acceleration $a$: the free surface (and every surface of equal pressure) tilts at an angle $\theta$ to the horizontal with $\tan\theta=\dfrac{a}{g}$, rising towards the rear; along a horizontal line the pressure increases towards the rear by $\rho a$ per metre.

In Interactive 1, choose water, set the depth to $h=0.50\ \text{m}$ with the lift at rest ($a=0$), and switch between the three vessel shapes. What happens to the force on the base and to the weight of the water?

The base readout shows $98.0\ \text{N}$ for all three shapes ($\rho ghA=1000\times9.8\times0.50\times0.020$), while the weight of water is $98.0\ \text{N}$ (straight), $127\ \text{N}$ (widening) and $83.3\ \text{N}$ (narrowing). The base feels only the pressure at its depth; the sloping walls carry or add the difference. Now set $a=+2.0\ \text{m/s}^2$: the base force rises to $118\ \text{N}$ because $g_\text{eff}=11.8\ \text{m/s}^2$; at $a=-9.8\ \text{m/s}^2$ (free fall) every gauge reading drops to zero.
Interactive 1 — Pressure with Depth, Vessel Shape and "Gravity"

A vessel with a base of area $0.020\ \text{m}^2$ stands in a lift. Choose the liquid, the vessel shape and the liquid depth $h$; the lift's acceleration $a$ (positive = upwards) changes the effective gravity $g+a$. Drag the probe, or press Play to lower it through the liquid: the graph on the right plots the gauge pressure against depth — a straight line of slope $\rho(g+a)$. Compare the force on the base with the weight of the liquid as you change the shape.

0.50 m0.30 m0 m/s²
gauge pressure at probe—
absolute pressure—
force on base (gauge)—
weight of liquid $m(g+a)$—

A bucket of water stands on the floor of a lift. The cable snaps and the lift falls freely. While it falls, the gauge pressure at a point $10\ \text{cm}$ below the water surface is

Pascal's law and hydraulic machines

Squeeze a closed plastic bottle full of water anywhere and the water squirts out equally hard from pinholes all over it. The extra pressure you create at one point is felt everywhere in the liquid. This follows from Result 7.5: the pressure at any point is the surface pressure plus $\rho gh$; raising the pressure at one point by $\Delta p$ raises it by the same $\Delta p$ everywhere, since the $\rho gh$ differences are fixed by the depths.

📐 Law 7.8 — Pascal's law

A change in pressure applied to an enclosed incompressible fluid at rest is transmitted undiminished to every point of the fluid and to the walls of its container.

Equivalently: in a fluid at rest (neglecting gravity), the pressure is the same at all points; with gravity, points at the same level have the same pressure, and the difference between two levels is $\rho gh$.

The hydraulic lift. Two cylinders of cross-sections $A_1$ (small) and $A_2$ (large), fitted with pistons, are connected and filled with oil. A force $F_1$ on the small piston creates a pressure $p=F_1/A_1$, which acts on the large piston too, giving an upward force $F_2=pA_2$.

📐 Result 7.9 — Hydraulic machines

For a hydraulic lift with pistons at the same level (frictionless, light pistons, incompressible fluid):

$$F_2=F_1\,\frac{A_2}{A_1},\qquad d_2=d_1\,\frac{A_1}{A_2},\qquad F_1d_1=F_2d_2 .$$

The force is multiplied by the area ratio, but the large piston moves a distance smaller by the same ratio (the volume of fluid pushed out of one cylinder enters the other), so the work output equals the work input: a hydraulic machine multiplies force, never energy. If the pistons are at different heights, use $p_1+\rho gh_1=p_2+\rho gh_2$ for the pressures under them.

The same principle runs hydraulic presses (for baling cotton or forging metal), car jacks, the arms of excavators and aircraft control surfaces, and the brakes of every car: the driver's foot pushes a small piston in the master cylinder, and the pressure is transmitted through the brake fluid to larger pistons at all four wheels, which press the brake pads with equal and much larger forces. A bubble of air in the brake line is dangerous because air is compressible: the pedal then squashes the bubble instead of transmitting the pressure.

✏️ Example 4 — A garage car hoist
In a car hoist the small piston has diameter $2.0\ \text{cm}$ and the large piston $30\ \text{cm}$. A car of mass $1200\ \text{kg}$ rests on the large piston. (a) With both pistons at the same level, what force on the small piston holds the car up? (b) How far must the small piston be pushed to raise the car by $10\ \text{cm}$? (c) Suppose instead that the small piston is $1.0\ \text{m}$ higher than the large one and the oil has density $800\ \text{kg/m}^3$. Find the force needed on the small piston. (Pistons light and frictionless.)
(a) $\dfrac{A_1}{A_2}=\left(\dfrac{2.0}{30}\right)^2=\dfrac1{225}$. $F_1=mg\,\dfrac{A_1}{A_2}=\dfrac{1200\times9.8}{225}=52\ \text{N}$ — the weight of about $5\ \text{kg}$.
(b) Equal volumes: $d_1=d_2\,\dfrac{A_2}{A_1}=0.10\times225=22.5\ \text{m}$. A real hoist does this in many short strokes, with a valve that stops the oil flowing back.
(c) Gauge pressure under the large piston: $p_2=\dfrac{11760}{\pi(0.15)^2}=1.664\times10^5\ \text{Pa}$. The small piston is $1.0\ \text{m}$ higher, where the pressure is less by $\rho gh=800\times9.8\times1.0=7840\ \text{Pa}$: $p_1=1.585\times10^5\ \text{Pa}$, so $F_1=p_1\times\pi(0.010)^2=49.8\ \text{N}$.
Check Work: in (a)–(b) $F_1d_1=52.3\times22.5=1.18\times10^3\ \text{J}$ and $mg\times0.10=1.18\times10^3\ \text{J}$ ✓ — no energy is gained. In (c) the oil column of height $1.0\ \text{m}$ in the tube helps a little.

In a hydraulic lift the large piston has $50$ times the area of the small one. The small piston is pushed down $10\ \text{cm}$. The large piston rises by

Buoyancy and Archimedes' principle

A bucket of water feels lighter while it is still under the surface of a well; a beach ball is hard to hold under water. Every body immersed in a fluid is pushed up, because the pressure on its lower parts is greater than the pressure on its upper parts.

Take a rectangular block of height $\ell$ and horizontal faces of area $A$, completely immersed in a liquid of density $\rho_\text{f}$ with its top face at depth $h$. The sideways pushes on the vertical faces cancel. The liquid pushes down on the top face with $(p_0+\rho_\text{f}gh)A$ and up on the bottom face with $(p_0+\rho_\text{f}g(h+\ell))A$. The net upward force is

$$F_B=\rho_\text{f}g\,\ell A=\rho_\text{f}Vg ,$$

the weight of liquid that would fill the block's volume $V$ — independent of the depth $h$. For a body of any shape, imagine replacing it by fluid of the same shape: that "fluid body" would be in equilibrium, so the surrounding fluid must push it up with a force equal to its weight. The surrounding fluid does not know what is inside the surface, so it pushes up on the real body with the same force.

📐 Law 7.10 — Archimedes' principle

A body wholly or partly immersed in a fluid at rest experiences an upward force, the buoyant force (upthrust), equal to the weight of the fluid it displaces:

$$F_B=\rho_\text{f}\,V_\text{sub}\,g ,$$

where $V_\text{sub}$ is the volume of the body below the fluid surface. The buoyant force acts vertically upwards through the centre of buoyancy, the centre of mass of the displaced fluid. It does not depend on the body's own density or mass. In a container accelerating vertically, $g$ is replaced by $g_\text{eff}=g+a$ (Result 7.7).

A body of density $\rho$ and volume $V$, released fully under the surface, feels its weight $\rho Vg$ down and $\rho_\text{f}Vg$ up. It sinks if $\rho\gt\rho_\text{f}$, rises if $\rho\lt\rho_\text{f}$ and stays where it is if they are equal. A rising body breaks the surface and settles with just enough of its volume submerged to displace its own weight.

📐 Result 7.11 — Floating bodies and apparent weight
  • Law of flotation: a floating body displaces its own weight of fluid. For a uniform body of density $\rho$ in a liquid of density $\rho_\text{f}$, the fraction of its volume submerged is $$\frac{V_\text{sub}}{V}=\frac{\rho}{\rho_\text{f}}\qquad(\rho\lt\rho_\text{f}).$$
  • Apparent weight of a body fully immersed in a liquid (e.g. read on a spring balance): $W'=W-F_B=W\left(1-\dfrac{\rho_\text{f}}{\rho}\right)$.
  • Relative density by weighing: $\dfrac{\rho}{\rho_w}=\dfrac{W}{W-W'_\text{water}}=\dfrac{\text{weight in air}}{\text{loss of weight in water}}$.
  • The fraction submerged does not change in a lift accelerating up or down, since both the weight and the buoyant force are multiplied by $g_\text{eff}/g$.

Newton's third law in buoyancy. The liquid pushes up on the immersed body with $F_B$, so the body pushes down on the liquid with $F_B$. If a beaker of water stands on a scale and a block hanging from a spring balance is lowered into it, the scale reading rises by exactly $F_B$ while the spring balance reading falls by $F_B$ — the total supported is still the weight of beaker, water and block. Interactive 2 shows both readings. A ship floats stably when its centre of buoyancy shifts sideways as it heels, giving a righting torque; a ship sails a little lower in fresh river water than in denser sea water, which is why cargo ships carry load-line marks for both.

✏️ Example 5 — Is the crown pure gold?
A gold-coloured ornament weighs $2.50\ \text{N}$ in air and $2.30\ \text{N}$ when hung from a spring balance fully immersed in water. (a) Find its volume and its relative density. (b) Pure gold has relative density $19.3$. If the ornament is an alloy of gold and silver (relative density $10.5$), find the fraction of gold by mass. (c) What would the balance read with the ornament fully immersed in an oil of relative density $0.80$?
(a) Loss of weight $=F_B=0.20\ \text{N}=\rho_wVg$: $V=\dfrac{0.20}{1000\times9.8}=2.04\times10^{-5}\ \text{m}^3=20.4\ \text{cm}^3$. Relative density $=\dfrac{2.50}{0.20}=12.5$ — not pure gold.
(b) Volumes add: for mass fraction $x$ of gold, $\dfrac1{12.5}=\dfrac{x}{19.3}+\dfrac{1-x}{10.5}$. So $0.0800-0.0952=x(0.0518-0.0952)$ and $x=0.35$: about $35\%$ gold by mass.
(c) The buoyant force is proportional to the liquid's density: $0.80\times0.20=0.16\ \text{N}$; the balance reads $2.50-0.16=2.34\ \text{N}$.
⏱ Shortcut Relative density = weight in air ÷ loss of weight in water. The loss in any liquid ÷ the loss in water = that liquid's relative density.
✏️ Example 6 — A cube floating between oil and water
A beaker contains water with a layer of oil (density $800\ \text{kg/m}^3$) on top. A wooden cube of side $10\ \text{cm}$ and density $860\ \text{kg/m}^3$ is placed in it; the oil layer is deep enough that the cube floats with part of it in each liquid and its top below the oil surface. (a) How much of the cube's height is in the water? (b) Check your answer by finding the difference in the forces of the liquids on the cube's bottom and top faces. (c) The oil is now poured off. How deep does the cube float in water alone?
Find how much of the cube's height lies in the water before you open the solution:
Why both $860\gt800$, so the cube sinks through the oil; $860\lt1000$, so it floats on the water: it settles at the interface.
(a) Archimedes for each liquid displaced: $\rho_cA\ell g=\rho_wAxg+\rho_oA(\ell-x)g$, so $860(10)=1000x+800(10-x)$, giving $200x=600$, $x=3.0\ \text{cm}$ in water and $7.0\ \text{cm}$ in oil.
(b) Going from the top face to the bottom face, the pressure increases by $\rho_og(0.070)+\rho_wg(0.030)=548.8+294=842.8\ \text{Pa}$. Times the face area $0.010\ \text{m}^2$: $8.43\ \text{N}$ up, equal to the weight $860\times10^{-3}\times9.8=8.43\ \text{N}$ ✓.
(c) In water alone the fraction submerged is $\dfrac{860}{1000}=0.86$: $8.6\ \text{cm}$ of the cube is under water.
Insight The oil above the cube pushes down on its top face, but it also raises the pressure at the bottom face by exactly the same amount, so any extra oil above the cube changes nothing. That is why Archimedes' principle works layer by layer.

In Interactive 2 the beaker of water and its stand read $19.6\ \text{N}$ on the scale. Set the block's density to $2700\ \text{kg/m}^3$ (aluminium; the block is a $10\ \text{cm}$ cube) and lower it until it is completely under water, still hanging from the spring balance. What does the scale under the beaker read now?

Lower the block fully: the readouts show buoyant force $9.80\ \text{N}$ ($\rho_wVg=1000\times10^{-3}\times9.8$), spring balance $16.7\ \text{N}$ (the weight $26.5\ \text{N}$ minus $9.80\ \text{N}$) and scale $29.4\ \text{N}$. The water pushes up on the block with $F_B$, so the block pushes down on the water with $F_B$ (Newton's third law): the scale gains exactly what the spring balance loses. Only if the string is cut and the block rests on the bottom does the scale carry the full weight.
Interactive 2 — Buoyancy Lab: Spring Balance and Scale

A cube of side $10\ \text{cm}$ hangs from a spring balance above a wide beaker standing on a scale (beaker and liquid weigh $19.6\ \text{N}$; the beaker is wide enough that the rise of the liquid level can be ignored). Choose the block's density and the liquid, and lower the block, or press Play. The graph shows how the buoyant force (blue) and the spring-balance reading (red) change with the depth of the block's lower face. A block less dense than the liquid floats: the string goes slack and the scale carries its whole weight. $g=9.8\ \text{m/s}^2$.

2700 kg/m³6.0 cm
weight of block $W$—
buoyant force $F_B$—
spring balance—
scale under beaker—
🧭 Problem-solving strategy — Hydrostatics problems
  1. Pressure at a point: start from a free surface (or a known pressure) and add $\rho gh$ going down, subtract going up, one liquid at a time.
  2. U-tubes and manometers: pick the horizontal level of the lowest interface and equate the pressures in the two arms there — only within one connected liquid.
  3. Walls and dams: pressure varies with depth, so integrate (or use the average pressure $\tfrac12\rho gH$ for a vertical rectangle from the surface down).
  4. Accelerating containers: replace $g$ by $g_\text{eff}=g+a$ (vertical) or tilt the surfaces of equal pressure by $\tan\theta=a/g$ (horizontal).
  5. Floating and sinking: draw the forces on the body — weight, buoyant force $\rho_\text{f}V_\text{sub}g$, string tension or normal force — and apply equilibrium. Then use Newton's third law for what the container and scale feel.
⚠️ JEE Main traps

1. Gauge or absolute? $\rho gh$ is the gauge pressure. Add $p_0$ only when the question asks for the total (absolute) pressure; forces on windows and walls with air on the other side use the gauge pressure.

2. "Same level, same pressure" across different liquids. It holds only inside one connected liquid at rest. In a U-tube with two liquids, equate pressures at the level of the interface, not at the free surfaces.

3. Pressure × area for a wall. On a vertical wall the pressure varies, so the force is $\tfrac12\rho gwH^2$ (the average pressure), not $\rho gH\times wH$; and it acts at $H/3$ from the bottom, not at the middle.

4. Hydraulic lift energy. Forces scale as the areas (diameter squared), distances inversely; the work in equals the work out. A factor of $10$ in diameter is a factor of $100$ in force.

5. Buoyancy in a lift, and the scale reading. The fraction submerged of a floating body does not change when the lift accelerates. A body hanging from a string into a beaker adds $F_B$ (not its weight) to the scale reading.

A cargo ship sails from a river (fresh water) into the sea (denser salt water) without changing its load. The ship

Exercises

Take $g=9.8\ \text{m/s}^2$, $\rho_\text{water}=1.0\times10^3\ \text{kg/m}^3$, $\rho_\text{Hg}=13.6\times10^3\ \text{kg/m}^3$ and $p_0=1.013\times10^5\ \text{Pa}$ unless a part says otherwise. Liquids are incompressible and at rest relative to their containers.

I
Pressure and depth.
  • 1 Find the gauge pressure at the bottom of a swimming pool $2.5\ \text{m}$ deep.
  • 2 Find the absolute pressure at the bottom of the pool in part 1.
  • 3 At what depth in sea water ($1030\ \text{kg/m}^3$) is the absolute pressure $3.0\ \text{atm}$?
  • 4 How tall a column of water exerts a pressure of $1\ \text{atm}$?
  • 5 A tall narrow jar and a wide bowl both contain water $20\ \text{cm}$ deep. Compare the pressures at their bottoms. Does the wide bowl's bottom feel a larger force? Explain.
  • 6 A blood-pressure reading of $120\ \text{mm Hg}$ is a gauge pressure. Express it in pascals.
  • 7 A standing person's brain is $0.45\ \text{m}$ above the heart. Taking the density of blood as $1060\ \text{kg/m}^3$, how much lower (in mm Hg) is the arterial pressure in the head than at the heart? Why is blood pressure measured with the cuff at heart level?
  • 8 Find the difference in pressure between two points in a lake, one $3.0\ \text{m}$ vertically below the other.
1 $\rho gh=1000\times9.8\times2.5=2.45\times10^4\ \text{Pa}$.
2 $p=1.013\times10^5+0.245\times10^5=1.26\times10^5\ \text{Pa}$.
3 Gauge pressure $2.0\ \text{atm}=2.026\times10^5\ \text{Pa}$: $h=\dfrac{2.026\times10^5}{1030\times9.8}=20\ \text{m}$ ($20.1\ \text{m}$).
4 $h=\dfrac{1.013\times10^5}{1000\times9.8}=10.3\ \text{m}$.
5 Equal pressures, $p_0+\rho g(0.20)$, since only the depth matters. The force on each bottom is pressure × area, so the bowl's larger bottom does feel a larger force — in proportion to its area, not to the amount of water.
6 $\rho_\text{Hg}gh=13.6\times10^3\times9.8\times0.120=1.60\times10^4\ \text{Pa}$.
7 $\Delta p=1060\times9.8\times0.45=4.68\times10^3\ \text{Pa}$; in mm Hg: $\dfrac{4675}{13.6\times10^3\times9.8}=0.035\ \text{m}=35\ \text{mm Hg}$. Readings taken at other levels would differ by $\rho gh$ of blood; measuring at heart level gives the pressure the heart produces.
8 $\Delta p=\rho g\Delta h=1000\times9.8\times3.0=2.94\times10^4\ \text{Pa}$, whatever the depths of the two points.
II
Barometers, manometers, walls and accelerating liquids.
  • 1 A mercury barometer on a hill reads $74.0\ \text{cm}$. Find the atmospheric pressure there.
  • 2 An open-tube mercury manometer connected to a gas cylinder shows the mercury $15.0\ \text{cm}$ higher in the open arm. Find the gauge and the absolute pressure of the gas.
  • 3 In a U-tube, a $15\ \text{cm}$ column of oil balances a $12\ \text{cm}$ column of water (both measured from the interface level). Find the density of the oil.
  • 4 A U-tube contains mercury. Water is poured into one arm until the water column is $27.2\ \text{cm}$ long. Find the difference between the mercury levels in the two arms.
  • 5 An aquarium's front glass is $1.2\ \text{m}$ wide and the water is $0.60\ \text{m}$ deep. Find the force of the water on the glass.
  • 6 At what height above the bottom of the glass in part 5 does this force act?
  • 7 A bucket of water is in a lift accelerating upwards at $2.0\ \text{m/s}^2$. Find the gauge pressure $30\ \text{cm}$ below the surface. What would it be if the lift were falling freely?
  • 8 A tanker lorry full of water to within a short distance of the top accelerates horizontally at $3.0\ \text{m/s}^2$. Taking $g=10\ \text{m/s}^2$, at what angle to the horizontal does the water surface settle, and which end is higher?
1 $p_0=13.6\times10^3\times9.8\times0.740=9.86\times10^4\ \text{Pa}$.
2 Gauge $=13.6\times10^3\times9.8\times0.150=2.00\times10^4\ \text{Pa}$; absolute $=1.013\times10^5+0.200\times10^5=1.21\times10^5\ \text{Pa}$.
3 $\rho_\text{oil}(15)=1000(12)$: $\rho_\text{oil}=800\ \text{kg/m}^3$.
4 At the level of the water–mercury interface: $\rho_wh_w=\rho_\text{Hg}h$, so $h=\dfrac{27.2}{13.6}=2.0\ \text{cm}$ (mercury higher in the other arm).
5 $F=\tfrac12\rho gwH^2=\tfrac12\times1000\times9.8\times1.2\times0.36=2.1\times10^3\ \text{N}$.
6 At $H/3=0.20\ \text{m}$ above the bottom.
7 $\rho(g+a)h=1000\times11.8\times0.30=3.5\times10^3\ \text{Pa}$ ($3540\ \text{Pa}$). In free fall $g_\text{eff}=0$, so the gauge pressure is zero at every depth.
8 $\tan\theta=\dfrac{a}{g}=0.30$, $\theta=16.7^\circ$; the surface is higher at the rear (the water "piles up" at the back as the lorry speeds up).
III
Pascal's law and hydraulic machines.
  • 1 The small piston of a hydraulic press has area $5.0\ \text{cm}^2$ and the large one $250\ \text{cm}^2$. A force of $200\ \text{N}$ acts on the small piston. Find the force on the large piston.
  • 2 In part 1 the small piston moves down $10\ \text{cm}$. How far does the large piston move?
  • 3 Compare the work done on the small piston with the work done by the large piston in parts 1–2. What does this show?
  • 4 A $1500\ \text{kg}$ car rests on the large piston (radius $15\ \text{cm}$) of a hoist; the small piston has radius $2.5\ \text{cm}$; both are at the same level. What force on the small piston holds the car?
  • 5 Find the gauge pressure of the oil in the hoist of part 4.
  • 6 In a car's brakes, the driver's pedal pushes the master-cylinder piston (area $2.0\ \text{cm}^2$) with $400\ \text{N}$. Each of the four wheel cylinders has a piston of area $6.0\ \text{cm}^2$. Find the force on each wheel piston and the total.
  • 7 Why does an air bubble in the brake fluid make the brakes feel "spongy" and weak?
  • 8 A hydraulic lift has a large piston of diameter $40\ \text{cm}$ carrying a load of $2000\ \text{kg}$ and a small piston of diameter $4.0\ \text{cm}$ placed $1.5\ \text{m}$ higher. The oil's density is $900\ \text{kg/m}^3$. Find the force needed on the small piston, and compare it with the value if both pistons were at the same level.
1 $F_2=200\times\dfrac{250}{5.0}=1.0\times10^4\ \text{N}$.
2 $d_2=10\ \text{cm}\times\dfrac{5.0}{250}=0.20\ \text{cm}=2.0\ \text{mm}$.
3 $200\times0.10=20\ \text{J}$ and $1.0\times10^4\times0.0020=20\ \text{J}$: equal. The press multiplies force but not energy (ideal, frictionless).
4 $F_1=mg\left(\dfrac{r_1}{r_2}\right)^2=14700\times\left(\dfrac{2.5}{15}\right)^2=\dfrac{14700}{36}=408\ \text{N}$.
5 $p=\dfrac{14700}{\pi(0.15)^2}=2.1\times10^5\ \text{Pa}$, about two atmospheres above atmospheric.
6 $p=\dfrac{400}{2.0\times10^{-4}}=2.0\times10^6\ \text{Pa}$, transmitted to every wheel: $F=2.0\times10^6\times6.0\times10^{-4}=1200\ \text{N}$ each, $4800\ \text{N}$ in total.
7 Pascal's law needs an incompressible fluid. Air is easily compressed, so pushing the pedal first squashes the bubble; the pressure rises less, the pedal travels further, and the pads press weakly.
8 $p_2=\dfrac{2000\times9.8}{\pi(0.20)^2}=1.560\times10^5\ \text{Pa}$; at the small piston, $1.5\ \text{m}$ higher, $p_1=p_2-900\times9.8\times1.5=1.428\times10^5\ \text{Pa}$; $F_1=p_1\times\pi(0.020)^2=179\ \text{N}$. At the same level it would be $19600/100=196\ \text{N}$.
IV
Buoyancy and floating.
  • 1 Find the buoyant force on a stone of volume $400\ \text{cm}^3$ fully immersed in water.
  • 2 The stone in part 1 has mass $1.2\ \text{kg}$. What does a spring balance read when the stone hangs from it fully immersed in water?
  • 3 Find the relative density of the stone.
  • 4 An iceberg (ice density $917\ \text{kg/m}^3$) floats in sea water ($1030\ \text{kg/m}^3$). What percentage of its volume is above the surface?
  • 5 A wooden block floats in water with $60\%$ of its volume submerged and in an oil with $75\%$ submerged. Find the densities of the wood and the oil.
  • 6 A raft $2.0\ \text{m}\times1.5\ \text{m}\times0.20\ \text{m}$ is made of wood of density $600\ \text{kg/m}^3$. What is the largest mass it can carry in fresh water without its top going under?
  • 7 A beaker of water on a scale reads $25.0\ \text{N}$. A metal block of weight $15.0\ \text{N}$ and volume $5.0\times10^{-4}\ \text{m}^3$, hanging from a spring balance, is lowered until it is fully immersed (not touching the bottom). Find the readings of the spring balance and the scale.
  • 8 A weather balloon holds $4.0\ \text{m}^3$ of helium (density $0.18\ \text{kg/m}^3$) in air of density $1.2\ \text{kg/m}^3$; the envelope and instruments have a mass of $2.0\ \text{kg}$. Find the net upward force on the balloon at launch (neglect the volume of the envelope and instruments).
1 $F_B=\rho_wVg=1000\times4.0\times10^{-4}\times9.8=3.92\ \text{N}$.
2 $W=1.2\times9.8=11.76\ \text{N}$; reading $=11.76-3.92=7.84\ \text{N}$.
3 $\dfrac{W}{F_B}=\dfrac{11.76}{3.92}=3.0$ (or $\rho=\dfrac{1.2}{4.0\times10^{-4}}=3000\ \text{kg/m}^3$).
4 Submerged fraction $\dfrac{917}{1030}=0.890$, so $11\%$ is above the surface.
5 $\rho_\text{wood}=0.60\times1000=600\ \text{kg/m}^3$; in the oil $0.75\rho_\text{oil}=600$, so $\rho_\text{oil}=800\ \text{kg/m}^3$.
6 Fully submerged, the raft ($V=0.60\ \text{m}^3$) displaces $600\ \text{kg}$ of water and has mass $360\ \text{kg}$: it can carry $240\ \text{kg}$.
7 $F_B=1000\times5.0\times10^{-4}\times9.8=4.9\ \text{N}$. Spring balance $15.0-4.9=10.1\ \text{N}$; scale $25.0+4.9=29.9\ \text{N}$. The total, $40.0\ \text{N}$, is unchanged.
8 $F_B=1.2\times4.0\times9.8=47.0\ \text{N}$; weight of helium $0.18\times4.0\times9.8=7.06\ \text{N}$; weight of the rest $19.6\ \text{N}$. Net upward force $=47.0-7.06-19.6=20\ \text{N}$ ($20.4\ \text{N}$).
🎯 Exam corner JEE Main · MCQJEE Main · Numerical

E1. JEE Main · MCQ The pistons of a hydraulic lift, at the same level, have diameters of $2.0\ \text{cm}$ and $20\ \text{cm}$. Taking $g=10\ \text{m/s}^2$, the least force on the small piston that can support a load of $1000\ \text{kg}$ on the large piston is (A) $1000\ \text{N}$ (B) $10\ \text{N}$ (C) $100\ \text{N}$ (D) $1.0\ \text{N}$

Idea Pascal's law: $\dfrac{F_1}{A_1}=\dfrac{F_2}{A_2}$, and $\dfrac{A_1}{A_2}=\left(\dfrac{d_1}{d_2}\right)^2=\dfrac1{100}$.
Force $F_1=\dfrac{1000\times10}{100}=100\ \text{N}$.
Answer (C) $100\ \text{N}$.
⏱ Shortcut (A) uses the diameter ratio instead of its square — the commonest slip on hydraulic lifts.

E2. JEE Main · Numerical A U-tube of uniform bore contains mercury (relative density $13.6$). Water is poured into one arm until the water column above the mercury is $68\ \text{cm}$ long. Find the difference, in mm, between the levels of mercury in the two arms. Give the answer to the nearest integer.

Level Equate pressures at the level of the water–mercury interface: $\rho_wg(0.68)=\rho_\text{Hg}g\,h$.
Number $h=\dfrac{0.68}{13.6}=0.050\ \text{m}=50\ \text{mm}$.
Answer $50$.

E3. JEE Main · MCQ A block floats in water in a tank with one quarter of its volume above the surface. The tank is placed in a lift that accelerates upwards at $g/2$. The fraction of the block's volume above the surface is now (A) $\tfrac14$ (B) $\tfrac18$ (C) $\tfrac38$ (D) $\tfrac16$

Idea In the lift both the weight (in the lift's frame) and the buoyant force use $g_\text{eff}=\tfrac32g$: $\rho Vg_\text{eff}=\rho_wV_\text{sub}g_\text{eff}$.
Cancel $g_\text{eff}$ cancels, so $V_\text{sub}/V=\rho/\rho_w=\tfrac34$ as before.
Answer (A) $\tfrac14$.
⏱ Shortcut Floating depth depends only on the density ratio — any change of "gravity" affects both sides equally.

E4. JEE Main · Numerical A wooden block floats in water with $60\%$ of its volume submerged. In a certain liquid it floats with $80\%$ of its volume submerged. Find the density of the liquid in $\text{kg/m}^3$ (density of water $1000\ \text{kg/m}^3$). Give the answer to the nearest integer.

Wood Flotation in water: $\rho_\text{wood}=0.60\times1000=600\ \text{kg/m}^3$.
Liquid $0.80\,\rho_\ell=600$, so $\rho_\ell=750\ \text{kg/m}^3$.
Answer $750$.
⏱ Shortcut The submerged fraction is inversely proportional to the liquid density: $\rho_\ell=1000\times\dfrac{0.60}{0.80}$.

E5. JEE Main · MCQ A beaker of water stands on a weighing scale. A solid of weight $W$ and density three times that of water, hanging from a spring balance, is lowered until it is completely immersed without touching the beaker. The increase in the reading of the weighing scale is (A) $0$ (B) $W$ (C) $\tfrac{2W}{3}$ (D) $\tfrac{W}{3}$

Buoyancy $F_B=\rho_wVg=\dfrac{\rho Vg}{3}=\dfrac W3$.
Third law The water pushes the solid up with $W/3$, so the solid pushes the water down with $W/3$; the scale reading rises by $W/3$ while the spring balance reads $W-W/3=2W/3$.
Answer (D) $\tfrac W3$.
⏱ Shortcut (C) is the spring-balance reading. Spring balance + scale increase must add up to $W$.

E6. JEE Main · Numerical A closed rectangular tank $4.0\ \text{m}$ long is completely full of water and accelerates horizontally along its length at $2.5\ \text{m/s}^2$. Find the difference, in kPa, between the pressures at the rear and front ends of its floor. Give the answer to the nearest integer.

Idea A horizontal column of water of length $L$ and cross-section $A$ along the floor accelerates with the tank, so the net force on it is $\rho ALa$; this comes from the pressure difference between its ends: $\Delta p\,A=\rho ALa$.
Number $\Delta p=\rho aL=1000\times2.5\times4.0=1.0\times10^4\ \text{Pa}=10\ \text{kPa}$, higher at the rear.
Answer $10$.
⏱ Shortcut Horizontally, pressure grows towards the rear at $\rho a$ per metre, just as it grows downwards at $\rho g$ per metre. The value of $g$ is not needed.
🔬 Research–Teaching NexusResearch-tutored · optional, about 45 minutes

Research question. How well does Archimedes' principle predict how deep a loaded boat floats — in fresh water and in salt water?

Why it matters. Every cargo ship carries load-line marks showing how deep it may safely float in tropical fresh water, summer sea water and winter North Atlantic water; overloading has sunk many ships. Naval architects, port authorities and offshore engineers use exactly the flotation law of this section, and oceanographers measure sea-water density (which depends on salinity and temperature) with floating hydrometers.

What to do.

  1. Take a straight-sided plastic food container as a "barge". Measure its base area $A$ and mark a millimetre scale up its side.
  2. Float it in a basin of tap water and add coins or washers in steps of known mass $m$. Record the depth $d$ of the waterline each time.
  3. Plot $d$ against the total mass (container plus load). Archimedes predicts a straight line of slope $1/(\rho A)$: find $\rho$ from your slope.
  4. Dissolve salt in the water (about $35\ \text{g}$ per litre, like sea water), stir well, and repeat. How much higher does the barge ride with the same load?

Tools: A straight-sided container, a ruler, coins or washers weighed on a kitchen scale, a basin, table salt, a spreadsheet.

Hand in: Both graphs, your two values of the water density with uncertainties, and a short explanation of why ships need separate fresh-water and sea-water load lines.

Going further. Load the barge off-centre and watch it tilt. Find the greatest off-centre load before it capsizes, and explain your result using the centre of buoyancy and the centre of mass.

Instructor note: tap water typically gives $\rho$ within $2$–$3\%$ of $1000\ \text{kg/m}^3$; the salt solution gives about $1020$–$1030\ \text{kg/m}^3$, so the barge rides $2$–$3\%$ higher. The main errors are reading the waterline (meniscus) and walls that are not quite vertical; a larger base area makes the depth changes smaller but the readings more stable.

🧪 Self-check quiz

0/5 correct

Q1. At a point inside a liquid at rest, the pressure

Q2. The working of a hydraulic brake is based on

Q3. If water (density $1.0\times10^3\ \text{kg/m}^3$) were used instead of mercury in a barometer at sea level, the height of the column would be about

Q4. An ice cube floats in a glass of water filled to the brim. When the ice melts, the water

Q5. A solid of density $4000\ \text{kg/m}^3$ hangs from a spring balance fully immersed in water. The balance reads