Chapter 7 · Properties of Solids and Liquids

7.5 Thermal Expansion, Calorimetry and Heat Transfer

Heat is energy on the move because of a temperature difference. It makes solids and liquids expand, warms them at a rate set by their specific heat capacity, melts and boils them at fixed temperatures, and flows by conduction, convection and radiation — every one of which JEE Main tests with a short, exact calculation.

Railway lines are laid with small gaps between the rails; long steel bridges rest on rollers at one end; a tight lid on a glass jar loosens under hot water; ice cubes cool a drink far more than the same mass of cold water; a pressure cooker cooks rice faster; a vacuum flask keeps tea hot for hours. All of these are about one thing — what heat does to matter, and how heat gets from one place to another.

This section completes Chapter 7 with the thermal properties of solids and liquids. We first separate heat from temperature, then study thermal expansion (with the thermal stress it causes in a clamped rod, which links straight back to Young's modulus in Section 7.1). Next comes the bookkeeping of heat — specific heat capacity, calorimetry, change of state and latent heat — and finally the three ways heat travels: conduction (with slabs in series and in parallel), convection and radiation. Expect one or two questions from this section in every JEE Main shift: a mixture of ice and water, a composite wall, a pendulum clock on a hot day, or a ratio from Stefan's law.

Heat, temperature and thermal expansion

Touch a metal railing and a wooden bench on a cold morning. The metal feels colder, yet a thermometer shows that both are at the same temperature — the metal simply carries heat away from your hand faster. Your skin senses the flow of heat, not the temperature. Physics keeps the two ideas strictly apart.

📘 Definition 7.17 — Heat and temperature

Temperature is the property that decides the direction of heat flow: when two bodies are placed in thermal contact, energy flows from the one at the higher temperature to the one at the lower temperature until their temperatures are equal (thermal equilibrium). Its SI unit is the kelvin (K).

Heat $Q$ is the energy transferred from one body or system to another solely because of a temperature difference between them. It is measured in joules; the older unit is the calorie, $1\ \text{cal}=4.186\ \text{J}$. A body does not "contain" heat — it contains internal energy; heat is energy in transit.

Temperature scales. A thermometer uses some property that changes steadily with temperature — the length of a mercury thread, the pressure of a gas at constant volume, the resistance of a platinum wire. Two reproducible fixed points calibrate it. On the Celsius scale the melting point of ice is $0\ ^\circ\text{C}$ and the boiling point of water (at $1\ \text{atm}$) is $100\ ^\circ\text{C}$; on the Fahrenheit scale they are $32\ ^\circ\text{F}$ and $212\ ^\circ\text{F}$. The absolute (Kelvin) scale has the same size of degree as Celsius but starts at absolute zero, $-273.15\ ^\circ\text{C}$. Because every scale is linear between the fixed points, the fraction of the way from ice point to steam point is the same on all of them.

📐 Result 7.22 — Converting between temperature scales

If a scale X reads $X_\text{ice}$ at the ice point and $X_\text{steam}$ at the steam point, and the thermometer property varies linearly with temperature, then a reading $X$ corresponds to

$$\frac{X-X_\text{ice}}{X_\text{steam}-X_\text{ice}}=\frac{t_C-0}{100}=\frac{t_F-32}{180}=\frac{T-273.15}{100}.$$

In particular $t_F=\tfrac95t_C+32$ and $T=t_C+273.15$. A temperature difference has the same value in kelvin and in degrees Celsius: $\Delta T\ (\text{K})=\Delta t\ (^\circ\text{C})$, while $1\ \text{K}=1.8\ ^\circ\text{F}$ of difference.

Thermal expansion. When a solid is heated its atoms vibrate with larger amplitude about their equilibrium positions. Because the force between neighbouring atoms is not symmetric — it is much harder to push atoms together than to pull them apart — the average spacing grows as the vibration grows. Every length in the body increases by the same fraction, so a heated plate keeps its shape but becomes a slightly larger copy of itself. For moderate temperature changes the fractional increase is proportional to the temperature rise.

📘 Definition 7.18 — Coefficients of linear, area and volume expansion

When the temperature of a body rises by a small amount $\Delta T$, its length $L$, area $A$ and volume $V$ increase by

$$\Delta L=\alpha L\,\Delta T,\qquad \Delta A=\beta A\,\Delta T,\qquad \Delta V=\gamma V\,\Delta T .$$

The constants $\alpha$ (coefficient of linear expansion), $\beta$ (coefficient of area, or superficial, expansion) and $\gamma$ (coefficient of volume, or cubical, expansion) are properties of the material, measured in $\text{K}^{-1}$ (equivalently $(^\circ\text{C})^{-1}$). They are nearly constant over moderate temperature ranges. Typical values of $\alpha$: invar $1\times10^{-6}$, glass $9\times10^{-6}$, steel $1.2\times10^{-5}$, copper $1.7\times10^{-5}$, brass $1.9\times10^{-5}$, aluminium $2.3\times10^{-5}\ \text{K}^{-1}$. Liquids have only $\gamma$ (mercury $1.8\times10^{-4}\ \text{K}^{-1}$); for gases $\gamma$ is far larger (about $1/T$ for an ideal gas at constant pressure).

📐 Result 7.23 — Relation between α, β and γ

For an isotropic solid (one that expands equally in every direction) and small $\alpha\,\Delta T$,

$$\beta=2\alpha,\qquad \gamma=3\alpha .$$

Proof. A square of side $L$ becomes $L(1+\alpha\Delta T)$ on each side, so its area becomes $L^2(1+\alpha\Delta T)^2=L^2(1+2\alpha\Delta T+\alpha^2\Delta T^2)$. Since $\alpha\Delta T$ is of order $10^{-3}$, the squared term is a million times smaller and is dropped: $\Delta A=2\alpha A\,\Delta T$. In the same way a cube gives $(1+\alpha\Delta T)^3\approx1+3\alpha\Delta T$. Consequences:

  • A hole or cavity expands exactly as if it were filled with the surrounding material — a hole in a heated plate gets larger.
  • Since the mass is unchanged, the density falls: $\rho'=\dfrac{\rho}{1+\gamma\Delta T}\approx\rho(1-\gamma\Delta T)$.

Liquids in containers. When a vessel filled with a liquid is heated, both expand. The liquid that overflows (or the rise you see in a thermometer tube) measures only the difference: the apparent expansion is $\Delta V_\text{app}=V(\gamma_\text{liquid}-\gamma_\text{vessel})\,\Delta T$, so $\gamma_\text{app}=\gamma_\text{real}-\gamma_\text{vessel}$. A mercury thermometer works because mercury expands about seven times more than glass.

Anomalous expansion of water. Water is the famous exception: when it is heated from $0\ ^\circ\text{C}$ to $4\ ^\circ\text{C}$ it contracts, and only above $4\ ^\circ\text{C}$ does it expand like a normal liquid. Its density is therefore greatest, $1000\ \text{kg/m}^3$, at about $4\ ^\circ\text{C}$, and ice (density about $920\ \text{kg/m}^3$) floats on water. In winter, the surface water of a lake cools and sinks until the whole lake is at $4\ ^\circ\text{C}$; after that, colder water stays on top and freezes first. The ice layer insulates the water below, and fish survive at the bottom at about $4\ ^\circ\text{C}$.

Bimetallic strip. Two strips of different metals (say brass, $\alpha=1.9\times10^{-5}$, and steel, $\alpha=1.2\times10^{-5}\ \text{K}^{-1}$) riveted together bend when heated, with the metal of larger $\alpha$ on the outside of the curve, and bend the other way when cooled. Electric irons, fire alarms and old car indicators use this to open and close a circuit.

📐 Result 7.24 — Thermal stress in a clamped rod

A rod of Young's modulus $Y$, coefficient of linear expansion $\alpha$ and cross-section $A$ is held between two rigid supports with no stress at the starting temperature. If its temperature changes by $\Delta T$ (and it neither buckles nor yields), the supports prevent the change of length $\alpha L\Delta T$, so the rod carries a strain $\alpha\Delta T$ and

$$\text{thermal stress}=Y\alpha\,\Delta T,\qquad\text{force on each support}\ F=YA\alpha\,\Delta T .$$

The stress is compressive if the rod is heated and tensile if it is cooled. It does not depend on the length of the rod.

The reasoning is that of Section 7.1: imagine the rod first expanding freely by $\alpha L\Delta T$, then being squeezed back to its original length by the supports. The squeezing strain is $\alpha L\Delta T/L=\alpha\Delta T$ and Hooke's law gives the stress.

Pendulum clocks and measuring scales. The period of a simple pendulum is $T=2\pi\sqrt{\ell/g}$ (derived in Chapter 10), so $T\propto\sqrt\ell$. If its temperature rises by $\Delta\theta$, $\ell$ grows by the fraction $\alpha\Delta\theta$ and the period by half that fraction:

$$\frac{\Delta T}{T}=\tfrac12\alpha\,\Delta\theta,\qquad\text{time lost per day}=\tfrac12\alpha\,\Delta\theta\times86\,400\ \text{s}.$$

A clock that is correct at $\theta_0$ loses time above $\theta_0$ (slower swings) and gains below it. In the same way a metal scale calibrated at $\theta_0$ has its markings spread apart when warmer, so it reads less than the true length: true length $=$ reading $\times(1+\alpha_\text{scale}\,\Delta\theta)$.

✏️ Example 1 — Rails, a hole and thermal stress
Steel rails ($\alpha=1.2\times10^{-5}\ \text{K}^{-1}$, $Y=2.0\times10^{11}\ \text{Pa}$, cross-section $7.5\times10^{-3}\ \text{m}^2$) are each $12.0\ \text{m}$ long and are laid at $15\ ^\circ\text{C}$. The hottest expected rail temperature is $45\ ^\circ\text{C}$. (a) What gap must be left between neighbouring rails? (b) If the rails were laid end to end with no gap and could not buckle, find the stress and the force in them at $45\ ^\circ\text{C}$. (c) An aluminium plate ($\alpha=2.3\times10^{-5}\ \text{K}^{-1}$) has a circular hole of diameter $4.00\ \text{cm}$ at $20\ ^\circ\text{C}$. Find the diameter of the hole at $220\ ^\circ\text{C}$ and the percentage increase in its area.
(a) $\Delta T=30\ \text{K}$: $\Delta L=\alpha L\Delta T=1.2\times10^{-5}\times12.0\times30=4.32\times10^{-3}\ \text{m}$. A gap of about $4.3\ \text{mm}$ is needed.
(b) Stress $=Y\alpha\Delta T=2.0\times10^{11}\times1.2\times10^{-5}\times30=7.2\times10^{7}\ \text{Pa}$ (compressive). Force $=7.2\times10^7\times7.5\times10^{-3}=5.4\times10^{5}\ \text{N}$ — the weight of about 55 tonnes, enough to buckle the track sideways.
(c) The hole expands like the metal: $d=4.00(1+2.3\times10^{-5}\times200)=4.00\times1.0046=4.018\ \text{cm}$. Area increase $\approx2\alpha\Delta T=2\times2.3\times10^{-5}\times200=9.2\times10^{-3}$, i.e. $0.92\%$.
Check The exact factor $(1.0046)^2-1=0.00922$ differs from $2\alpha\Delta T$ only in the third significant figure — dropping $(\alpha\Delta T)^2$ is safe. The stress in (b) does not involve the rail length: a 1 m rail and a 12 m rail would be equally stressed.
✏️ Example 2 — A pendulum clock through the seasons
A pendulum clock with a metal pendulum loses $8\ \text{s}$ a day when the room is at $30\ ^\circ\text{C}$ and gains $4\ \text{s}$ a day at $15\ ^\circ\text{C}$. (a) At what temperature does it keep correct time? (b) Find the coefficient of linear expansion of the pendulum's metal. (c) How much does it gain or lose per day at $0\ ^\circ\text{C}$?
Find the correct-time temperature and $\alpha$ before you open the solution:
Model If the clock is correct at $\theta_0$, the time lost per day at $\theta$ is $\tfrac12\alpha(\theta-\theta_0)\times86\,400\ \text{s}$; a gain is a negative loss.
(a) $8=\tfrac12\alpha(30-\theta_0)(86\,400)$ and $-4=\tfrac12\alpha(15-\theta_0)(86\,400)$. Dividing: $-2=\dfrac{30-\theta_0}{15-\theta_0}$, so $-30+2\theta_0=30-\theta_0$ and $\theta_0=20\ ^\circ\text{C}$.
(b) $\alpha=\dfrac{2\times8}{86\,400\times10}=1.85\times10^{-5}\ \text{K}^{-1}$ (close to brass).
(c) The loss is linear in $\theta-\theta_0$: $0.8\ \text{s}$ per day for each degree. At $0\ ^\circ\text{C}$, $\theta-\theta_0=-20\ \text{K}$, so it gains $16\ \text{s}$ a day.
⏱ Shortcut Loss is linear in temperature: $+8$ at $30$ and $-4$ at $15$ means $12\ \text{s}$ per $15\ \text{K}$, i.e. $0.8\ \text{s/K}$, and the zero is $8/0.8=10\ \text{K}$ below $30\ ^\circ\text{C}$.

A steel plate has a circular hole of diameter $d$. The plate is heated uniformly. The hole

Specific heat capacity, calorimetry and change of state

Put a pan of water and an empty iron pan of the same mass on identical burners. The iron pan is too hot to touch within a minute; the water is barely warm. The same heat produces very different temperature rises in different substances. Water needs about nine times more heat than iron for each kilogram and each degree — which is why the sea warms and cools slowly, why water is used in car radiators and hot-water bottles, and why coastal climates are mild.

📘 Definition 7.19 — Heat capacity, specific heat capacity and water equivalent

If a heat $Q$ raises the temperature of a body by $\Delta T$ (with no change of state), the heat capacity of the body is $C=\dfrac{Q}{\Delta T}$ (unit $\text{J/K}$). The specific heat capacity of the material is the heat capacity per unit mass,

$$c=\frac{Q}{m\,\Delta T},\qquad\text{so}\qquad Q=mc\,\Delta T,$$

in $\text{J kg}^{-1}\text{K}^{-1}$. The molar specific heat capacity is the heat per mole per kelvin, $C_m=Mc$ (with $M$ the molar mass). The water equivalent of a body is the mass of water that has the same heat capacity: $W=\dfrac{mc}{c_\text{w}}$.

Values used in this course (unless a problem states others): water $c_\text{w}=4200\ \text{J kg}^{-1}\text{K}^{-1}$ (measured $4186$), ice $2100$, steam about $2000$, aluminium $900$, iron $460$, copper $390$–$400$, lead $130\ \text{J kg}^{-1}\text{K}^{-1}$.

Calorimetry means "heat measuring". A calorimeter is a thin, polished copper or aluminium can with a stirrer, kept inside an insulated jacket so that very little heat enters or leaves. Bodies at different temperatures are mixed inside it — the method of mixtures — and their final common temperature is measured.

📐 Law 7.25 — Principle of calorimetry

When bodies at different temperatures are brought into thermal contact inside an isolated system (no heat exchanged with the surroundings, no work done, no chemical reaction), heat flows until they reach a common temperature, and

$$\text{total heat lost by the hotter bodies}=\text{total heat gained by the colder bodies},\qquad\text{i.e.}\quad\sum Q_i=0 .$$

It is simply conservation of energy. With no change of state, two bodies mixed reach $T_f=\dfrac{m_1c_1T_1+m_2c_2T_2}{m_1c_1+m_2c_2}$ — a weighted average of the starting temperatures, weighted by heat capacity.

✏️ Example 3 — Finding a specific heat by the method of mixtures
A $0.20\ \text{kg}$ metal block is heated to $100\ ^\circ\text{C}$ in boiling water and quickly dropped into a $0.10\ \text{kg}$ copper calorimeter ($c=400\ \text{J kg}^{-1}\text{K}^{-1}$) holding $0.15\ \text{kg}$ of water at $25\ ^\circ\text{C}$. After stirring, the temperature settles at $32\ ^\circ\text{C}$. (a) Find the water equivalent of the calorimeter. (b) Find the specific heat capacity of the metal. (c) Name one error that makes the result too small.
(a) $W=\dfrac{0.10\times400}{4200}=9.5\times10^{-3}\ \text{kg}=9.5\ \text{g}$ — the calorimeter behaves like an extra $9.5\ \text{g}$ of water.
Heat gained Water and calorimeter rise by $7\ \text{K}$: $(0.15\times4200+0.10\times400)\times7=(630+40)\times7=4690\ \text{J}$.
(b) Heat lost by the block, falling $68\ \text{K}$: $0.20\,c\times68=13.6\,c$. Setting $13.6\,c=4690$: $c=345\ \text{J kg}^{-1}\text{K}^{-1}$.
(c) Heat lost to the air while the block is being transferred (or through the calorimeter walls) means the water gains less than the block really gave: the measured $c$ comes out too small. Transfer quickly and use a lid.
Check $c=345$ lies between copper and iron — sensible for a metal such as zinc or brass. Forgetting the calorimeter would give $c=\dfrac{4410}{13.6}=324$, about $6\%$ low.

Change of state. Heat a block of ice from $-20\ ^\circ\text{C}$ at a steady rate. Its temperature rises until it reaches $0\ ^\circ\text{C}$ — and then stops rising, although heat is still going in. Ice and water coexist at $0\ ^\circ\text{C}$ until the last of the ice has melted; only then does the temperature climb again. At $100\ ^\circ\text{C}$ (at $1\ \text{atm}$) a second, much longer plateau appears while the water boils. During a change of state the heat supplied does not increase the random kinetic energy of the molecules (the temperature) but breaks the bonds that hold them in the solid or liquid: it increases their potential energy, and so the internal energy, at constant temperature.

📘 Definition 7.20 — Latent heat

The latent heat $L$ of a change of state is the heat needed to change unit mass of a substance from one state to the other at constant temperature and pressure:

$$Q=mL .$$

Its unit is $\text{J/kg}$. The same heat is released in the reverse change (freezing, condensation). For water at $1\ \text{atm}$ we use: latent heat of fusion $L_f=3.36\times10^5\ \text{J/kg}$ ($80\ \text{cal/g}$; measured $3.34\times10^5$) at $0\ ^\circ\text{C}$, and latent heat of vaporisation $L_v=2.26\times10^6\ \text{J/kg}$ ($540\ \text{cal/g}$) at $100\ ^\circ\text{C}$.

The temperatures at which the changes happen depend on pressure. Raising the pressure raises the boiling point — a pressure cooker at about $2\ \text{atm}$ boils water at about $120\ ^\circ\text{C}$ and cooks faster — while on a high mountain water boils below $90\ ^\circ\text{C}$. For ice, extra pressure lowers the melting point slightly: a wire with weights hung from it cuts slowly through a block of ice, the ice refreezing above the wire (regelation). Some substances, such as dry ice (solid carbon dioxide) and camphor, pass directly from solid to vapour — sublimation. Steam at $100\ ^\circ\text{C}$ scalds far worse than water at $100\ ^\circ\text{C}$, because each kilogram that condenses on the skin releases an extra $2.26\times10^6\ \text{J}$.

🧭 Problem-solving strategy — Mixtures with ice (or steam)
  1. Do not assume the final state. First compute two benchmark heats, both measured to $0\ ^\circ\text{C}$: $Q_\text{need}$ = heat for all the ice to warm to $0\ ^\circ\text{C}$ and melt; $Q_\text{avail}$ = heat the warm water (and calorimeter) gives out in cooling to $0\ ^\circ\text{C}$.
  2. If $Q_\text{avail}\gt Q_\text{need}$: all the ice melts and $T_f\gt0$. Write one heat balance with $T_f$ unknown (the melted ice warms from $0$ to $T_f$).
  3. If $Q_\text{avail}\lt Q_\text{need}$ (but enough to bring the ice to $0\ ^\circ\text{C}$): $T_f=0\ ^\circ\text{C}$ and only a mass $\dfrac{Q_\text{avail}-Q_\text{warm ice}}{L_f}$ of ice melts.
  4. If $Q_\text{avail}$ is not even enough to warm the ice to $0\ ^\circ\text{C}$, some water freezes; compare again using the heat its freezing releases. For steam, use the same idea with $L_v$ and $100\ ^\circ\text{C}$.
✏️ Example 4 — Ice in a glass of water
$50\ \text{g}$ of ice at $-20\ ^\circ\text{C}$ is put into $200\ \text{g}$ of water at $30\ ^\circ\text{C}$ in a container of negligible heat capacity. Take $c_\text{w}=4200$, $c_\text{ice}=2100\ \text{J kg}^{-1}\text{K}^{-1}$ and $L_f=3.36\times10^5\ \text{J/kg}$. (a) Find the final temperature. (b) What is the largest mass of ice at $-20\ ^\circ\text{C}$ that this water could melt completely?
Find the final temperature before you open the solution:
Benchmarks Ice to $0\ ^\circ\text{C}$: $0.050\times2100\times20=2100\ \text{J}$; melting: $0.050\times3.36\times10^5=16\,800\ \text{J}$; so $Q_\text{need}=18\,900\ \text{J}$. Water cooling to $0\ ^\circ\text{C}$: $Q_\text{avail}=0.200\times4200\times30=25\,200\ \text{J}$.
Decide $25\,200\gt18\,900$: all the ice melts, and $6300\ \text{J}$ is left over to warm the whole $250\ \text{g}$ of water above $0\ ^\circ\text{C}$.
(a) $T_f=\dfrac{6300}{0.250\times4200}=6.0\ ^\circ\text{C}$.
(b) Each kilogram of ice at $-20\ ^\circ\text{C}$ needs $2100\times20+3.36\times10^5=3.78\times10^5\ \text{J}$ to become water at $0\ ^\circ\text{C}$. The water can give $25\,200\ \text{J}$, so at most $\dfrac{25\,200}{3.78\times10^5}=0.0667\ \text{kg}=66.7\ \text{g}$ — only $16.7\ \text{g}$ more than was used.
Check Full balance: heat lost by the water $0.2\times4200\times(30-6)=20\,160\ \text{J}$; heat gained by the ice $2100+16\,800+0.05\times4200\times6=20\,160\ \text{J}$ ✓. Ignoring latent heat would have given a wildly wrong $T_f\approx20\ ^\circ\text{C}$.

In the widget, drop $100\ \text{g}$ of ice at $-10\ ^\circ\text{C}$ into $200\ \text{g}$ of water at $40\ ^\circ\text{C}$. What will the final state be?

Set ice $100\ \text{g}$ at $-10\ ^\circ\text{C}$ and water $200\ \text{g}$ at $40\ ^\circ\text{C}$. The readouts show: ice needs $35.7\ \text{kJ}$ to reach $0\ ^\circ\text{C}$ and melt; the water can give only $33.6\ \text{kJ}$ cooling to $0\ ^\circ\text{C}$; final temperature $0\ ^\circ\text{C}$; ice melted $93.8\ \text{g}$ ($6.25\ \text{g}$ left). On the graph the red water line reaches $0\ ^\circ\text{C}$ while the blue ice curve is still on its melting plateau, so heat stops flowing there. The answer $23\ ^\circ\text{C}$ comes from treating the ice as cold water and forgetting latent heat — the plateau is $33.6\ \text{kJ}$ long, sixteen times the heat needed to warm the ice to $0\ ^\circ\text{C}$.
Interactive 1 — Mix Ice and Water: Where Does the Temperature Settle?

Choose the mass and temperature of the ice and of the warm water ($c_\text{w}=4200$, $c_\text{ice}=2100\ \text{J kg}^{-1}\text{K}^{-1}$, $L_f=3.36\times10^5\ \text{J/kg}$, no losses). The graph plots each body's temperature against the heat $Q$ that has passed from water to ice: the red water line falls, the blue ice curve rises with a flat melting plateau at $0\ ^\circ\text{C}$. Heat stops flowing where they meet. Press Play to watch the heat flow and the ice melt.

100 g−10 °C200 g40 °C
ice: to 0 °C + melt—
water: cooling to 0 °C—
final temperature—
ice melted—

Equal masses of ice at $0\ ^\circ\text{C}$ and water at $40\ ^\circ\text{C}$ are mixed in an insulated flask ($c_\text{w}=4.2\ \text{J g}^{-1}\text{K}^{-1}$, $L_f=336\ \text{J/g}$). The final state is

Conduction: thermal conductivity and composite slabs

Heat travels in three ways. In conduction it passes through a material from hotter to colder parts by collisions between neighbouring particles (and, in metals, mainly by free electrons), with no bulk movement of the material. Hold one end of a steel spoon in a flame and the other end soon becomes hot; a wooden spoon stays cool. When the two faces of a slab are held at fixed temperatures, the temperatures inside first change, then settle: in this steady state no part of the slab is warming any more, so heat flows through every cross-section at the same rate.

📐 Law 7.26 — Fourier's law of heat conduction

For a slab or rod of length (thickness) $L$ and uniform cross-section $A$, with its faces held at $T_1$ and $T_2$ ($T_1\gt T_2$), sides insulated, and in the steady state, the rate of heat flow (heat current) is

$$H=\frac{dQ}{dt}=\frac{kA\,(T_1-T_2)}{L},$$

and the temperature falls linearly from $T_1$ to $T_2$ along the slab. More generally $H=-kA\dfrac{dT}{dx}$, where $\dfrac{dT}{dx}$ is the temperature gradient. The constant $k$ is the thermal conductivity of the material.

📘 Definition 7.21 — Thermal conductivity and thermal resistance

The thermal conductivity $k$ of a material is the rate of heat flow through unit area of it per unit temperature gradient, in $\text{W m}^{-1}\text{K}^{-1}$. Typical values: silver $406$, copper $385$–$400$, aluminium $205$, steel $50$, ice $2.2$, glass $0.8$–$1.0$, brick $0.6$–$0.8$, water $0.6$, wood $0.1$–$0.2$, polystyrene foam $0.03$–$0.04$, still air $0.025\ \text{W m}^{-1}\text{K}^{-1}$.

The thermal resistance of a slab is $R=\dfrac{L}{kA}$ (unit $\text{K/W}$), so that $H=\dfrac{T_1-T_2}{R}$ — the thermal version of $I=\dfrac{V}{R}$, with temperature difference in place of potential difference and heat current in place of electric current.

Good conductors are used where heat must move quickly — cooking pans, the copper base of a kettle, heat sinks on computer chips. Poor conductors (insulators) keep heat where it is wanted: woollen clothes and fur trap still air, double-glazed windows sandwich a layer of air or gas, and refrigerators and ice boxes are lined with foam.

📐 Result 7.27 — Slabs in series and in parallel

Series (slabs one after another, the same heat current $H$ through each, in the steady state):

$$R_\text{eq}=R_1+R_2+\cdots,\qquad H=\frac{T_\text{hot}-T_\text{cold}}{R_1+R_2+\cdots}.$$

The temperature drop across each slab is $HR_i$ — largest across the worst conductor. For two slabs of equal area, the equivalent conductivity is $k_\text{eq}=\dfrac{L_1+L_2}{L_1/k_1+L_2/k_2}$; for equal thicknesses $k_\text{eq}=\dfrac{2k_1k_2}{k_1+k_2}$.

Parallel (slabs side by side between the same two temperatures):

$$\frac1{R_\text{eq}}=\frac1{R_1}+\frac1{R_2}+\cdots,\qquad H=H_1+H_2+\cdots .$$

For equal lengths, $k_\text{eq}=\dfrac{k_1A_1+k_2A_2}{A_1+A_2}$. The junction temperature of two slabs in series follows from equal heat currents: $\dfrac{k_1A_1(T_1-T_j)}{L_1}=\dfrac{k_2A_2(T_j-T_2)}{L_2}$.

Growth of ice on a pond. On a freezing night the air above a pond is at $-\theta$ (below $0\ ^\circ\text{C}$) and the water under the ice is at $0\ ^\circ\text{C}$. When the ice is $x$ thick, heat conducted up through it is $H=\dfrac{kA\theta}{x}$; this heat comes from water freezing on the underside. If a thickness $dx$ freezes in time $dt$, the heat released is $\rho A\,dx\,L_f$, so

$$\rho AL_f\frac{dx}{dt}=\frac{kA\theta}{x}\quad\Rightarrow\quad t=\frac{\rho L_f}{2k\theta}\left(x_2^2-x_1^2\right)$$

for the ice to thicken from $x_1$ to $x_2$ (integrating $x\,dx$). The thicker the ice, the slower it grows; doubling the thickness from zero takes four times as long.

✏️ Example 5 — Copper and steel, end to end and side by side
A copper rod ($k=400\ \text{W m}^{-1}\text{K}^{-1}$) and a steel rod ($k=50\ \text{W m}^{-1}\text{K}^{-1}$), each $0.50\ \text{m}$ long with cross-section $4.0\ \text{cm}^2$ and insulated sides, are placed between a steam bath at $100\ ^\circ\text{C}$ and an ice bath at $0\ ^\circ\text{C}$. (a) They are joined end to end, copper towards the steam. Find the heat current and the temperature of the junction. (b) They are placed side by side, each touching both baths. Find the total heat current. (c) Find the equivalent thermal conductivity in each case.
Find the junction temperature in (a) and the heat current in (b) first:
Resistances $A=4.0\times10^{-4}\ \text{m}^2$. $R_\text{Cu}=\dfrac{0.50}{400\times4.0\times10^{-4}}=3.125\ \text{K/W}$; $R_\text{st}=\dfrac{0.50}{50\times4.0\times10^{-4}}=25\ \text{K/W}$.
(a) Series: $H=\dfrac{100}{3.125+25}=3.56\ \text{W}$. Junction: $T_j=100-HR_\text{Cu}=100-3.556\times3.125=88.9\ ^\circ\text{C}$. Almost all of the $100\ \text{K}$ drop is across the steel.
(b) Parallel: $H=\dfrac{100}{3.125}+\dfrac{100}{25}=32+4.0=36\ \text{W}$ — about ten times the series value.
(c) Series (equal lengths): $k_\text{eq}=\dfrac{2\times400\times50}{450}=88.9\ \text{W m}^{-1}\text{K}^{-1}$. Parallel (equal areas): $k_\text{eq}=\dfrac{400+50}{2}=225\ \text{W m}^{-1}\text{K}^{-1}$.
⏱ Shortcut For equal $L$ and $A$ in series, $T_j=\dfrac{k_1T_1+k_2T_2}{k_1+k_2}=\dfrac{400\times100+50\times0}{450}=88.9\ ^\circ\text{C}$ — a "conductivity-weighted average", no resistances needed.
Check Copper's drop $3.556\times3.125=11.1\ \text{K}$ plus steel's $3.556\times25=88.9\ \text{K}$ add to $100\ \text{K}$ ✓. The ratio of drops, $1:8$, is the ratio of resistances.

In the widget, choose series with $k_1=400$ (hot side), $k_2=50\ \text{W m}^{-1}\text{K}^{-1}$ and slab 1 only $2\ \text{cm}$ thick (so slab 2 is $8\ \text{cm}$). The hot face is at $100\ ^\circ\text{C}$, the cold face at $0\ ^\circ\text{C}$. Roughly what is the junction temperature?

Set series, $k_1=400$, $k_2=50$, slab 1 thickness $2\ \text{cm}$. The readouts show $R_\text{eq}=0.165\ \text{K/W}$, heat current $606\ \text{W}$ and junction temperature $97\ ^\circ\text{C}$: $R_1=\tfrac{0.02}{400\times0.01}=0.005\ \text{K/W}$, $R_2=\tfrac{0.08}{50\times0.01}=0.16\ \text{K/W}$, $H=\tfrac{100}{0.165}=606\ \text{W}$, $T_j=100-606\times0.005=97.0\ ^\circ\text{C}$. The temperature drop divides in the ratio of the thermal resistances (1 : 32), not of the thicknesses. Press Play to see the profile build up from cold: heat flowing in at the hot face exceeds heat flowing out at the cold face until the steady state is reached.
Interactive 2 — Heat Through a Composite Slab

Two slabs ($10\ \text{cm}$ in total, face area $0.010\ \text{m}^2$, sides insulated) sit between a hot face at $100\ ^\circ\text{C}$ and a cold face at $0\ ^\circ\text{C}$. In series they are stacked one after the other; in parallel each is $10\ \text{cm}$ long with half the area. The graph shows temperature against position: dashed is the steady state, solid is the slab now. Press Play to start from a cold slab and watch heat soak in until heat in equals heat out.

200505 cm
$R_\text{eq}$—
steady heat current $H$—
junction / split—
heat in → out now—

Two slabs of the same area and thickness, with conductivities $k$ and $2k$, are placed in series. The outer face of the $k$ slab is at $90\ ^\circ\text{C}$ and the outer face of the $2k$ slab is at $0\ ^\circ\text{C}$. In the steady state the interface is at

Convection and radiation

In convection heat is carried by the bulk movement of a fluid. Water at the bottom of a pan is heated, expands, becomes less dense and rises (buoyancy, Section 7.2); cooler, denser water sinks to take its place, and a circulating convection current spreads the heat through the whole pan. Convection is impossible in solids and needs gravity for its natural form.

📘 Definition 7.22 — Convection and radiation

Convection is the transfer of heat by the actual movement of the heated fluid. It is natural (free) when the flow is driven by density differences under gravity, and forced when a pump or fan drives the flow (a car radiator, a hair-dryer, the blood circulation in the body).

Thermal radiation is the transfer of energy by electromagnetic waves (mainly infrared at everyday temperatures) emitted by every body because of its temperature. It needs no medium, travels at the speed of light, and is the only way heat reaches the Earth from the Sun across empty space.

Everyday convection: the sea breeze — by day the land heats up faster than the sea (water's larger specific heat), the air over the land rises, and cooler air flows in from the sea; the land breeze blows the other way at night when the land cools faster. On a global scale, air heated at the equator rises and flows towards the poles, and the Earth's rotation turns the returning surface flow into the trade winds. A room heater works best near the floor, an air conditioner near the ceiling.

Emitting and absorbing radiation. Radiation falling on a surface is partly reflected, partly transmitted and partly absorbed. Dark, rough surfaces absorb most of it; shiny, white surfaces reflect most of it. A surface that is a good absorber at some wavelength is equally a good emitter at that wavelength — a black kettle cools faster than a polished one, and white clothes are cooler in summer.

📘 Definition 7.23 — Black body and emissivity

A black body is an ideal body that absorbs all the radiation falling on it, whatever its wavelength; at a given temperature it also emits the most radiation that any body can. A small hole in a hollow enclosure with a blackened interior is an excellent practical black body.

The emissivity $e$ of a surface ($0\le e\le1$) is the ratio of the power it radiates to the power a black body of the same area and temperature would radiate: $e=1$ for a black body, about $0.95$ for lamp-black and human skin, about $0.03$ for polished silver.

📐 Law 7.28 — Stefan–Boltzmann law

The power radiated by a body of surface area $A$, emissivity $e$ and absolute temperature $T$ is

$$P=e\sigma AT^4,\qquad\sigma=5.67\times10^{-8}\ \text{W m}^{-2}\text{K}^{-4}.$$

A body at $T$ in surroundings at $T_0$ also absorbs radiation from them, so its net rate of loss by radiation is $P_\text{net}=e\sigma A\left(T^4-T_0^4\right)$. Temperatures must be in kelvin.

📐 Law 7.29 — Wien's displacement law

The radiation from a black body is spread over all wavelengths, but its intensity peaks at a wavelength $\lambda_m$ that is inversely proportional to the absolute temperature:

$$\lambda_mT=b,\qquad b=2.9\times10^{-3}\ \text{m K}.$$

As a body is heated its glow moves from dull red through orange and yellow to white (and the hottest stars look blue-white). The Sun's spectrum peaks near $500\ \text{nm}$, giving a surface temperature near $5800\ \text{K}$.

A vacuum flask fights all three modes at once: the vacuum between its double glass walls stops conduction and convection, the silvered inner surfaces reflect radiation back (and, having low emissivity, radiate little themselves), and the cork or plastic stopper — a poor conductor — blocks convection and conduction at the mouth.

✏️ Example 6 — A glowing sphere
A small sphere of radius $2.0\ \text{cm}$ with a blackened surface ($e=1$) is kept at $727\ ^\circ\text{C}$ in a room at $27\ ^\circ\text{C}$. (a) Find the power it radiates and its net rate of loss of energy by radiation. (b) At what wavelength is its emission strongest? (c) If its temperature were raised to $1727\ ^\circ\text{C}$, by what factor would the radiated power grow, and where would the peak move?
Kelvin first $T=727+273=1000\ \text{K}$, $T_0=300\ \text{K}$. Area $A=4\pi r^2=4\pi(0.020)^2=5.03\times10^{-3}\ \text{m}^2$.
(a) $P=\sigma AT^4=5.67\times10^{-8}\times5.03\times10^{-3}\times10^{12}=285\ \text{W}$. Net: $\sigma A(T^4-T_0^4)=285\times\left(1-0.0081\right)=283\ \text{W}$ — the room returns less than $1\%$.
(b) $\lambda_m=\dfrac{2.9\times10^{-3}}{1000}=2.9\times10^{-6}\ \text{m}=2.9\ \mu\text{m}$, in the infrared — the sphere glows only a dull red, since only the short-wavelength tail is visible.
(c) $1727\ ^\circ\text{C}=2000\ \text{K}$: twice the absolute temperature, so $P$ grows by $2^4=16$ (to about $4.6\ \text{kW}$) and the peak halves to $1.45\ \mu\text{m}$.
Check Using Celsius would give the factor $(1727/727)^4\approx32$ — wrong. Ratios in Stefan's and Wien's laws are always ratios of kelvin temperatures.
🚀 Beyond JEE Main (JEE Advanced) — Newton's law of cooling

Newton's law of cooling is not in the JEE Main 2026 syllabus list (it is listed for JEE Advanced 2026 and in the CBSE syllabus). This box is for interest only; nothing here is used in the exercises, the Exam corner or the quiz.

For a body only a little hotter than its surroundings, the total rate of heat loss (by convection and radiation together) is roughly proportional to the temperature excess: $-\dfrac{dT}{dt}=K\,(T-T_0)$. Then the excess decays exponentially, $T-T_0=(T_i-T_0)e^{-Kt}$, and a useful average form is $\dfrac{T_1-T_2}{t}=K\left(\dfrac{T_1+T_2}{2}-T_0\right)$. For radiation alone this follows from Stefan's law: when $T-T_0$ is small, $T^4-T_0^4\approx4T_0^3(T-T_0)$.

⚠️ JEE Main traps

1. Celsius in Stefan's or Wien's law. $P\propto T^4$ and $\lambda_m\propto1/T$ need kelvin. Only for temperature differences (expansion, $Q=mc\Delta T$, Fourier's law) are $^\circ\text{C}$ and K interchangeable.

2. Using α where β or γ is needed. Area grows by $2\alpha\Delta T$, volume by $3\alpha\Delta T$, density falls by $\gamma\Delta T$; a hole or cavity expands like the material. For a pendulum the period changes by $\tfrac12\alpha\Delta\theta$ — and a hot clock loses time.

3. Assuming all the ice melts. Always compare the heat available in cooling to $0\ ^\circ\text{C}$ with the heat needed to warm and melt all the ice before writing a balance with $T_f$ unknown. A negative $T_f$ from a mixing equation is the sign you skipped this.

4. Adding conductivities in series. In series the thermal resistances $L/(kA)$ add, not the $k$'s; the larger temperature drop is across the poorer conductor. Two identical rods side by side carry four times the heat current of the same rods end to end.

5. Forgetting the calorimeter, or the latent heat of steam. Include the calorimeter's $mc$ (its water equivalent) in the heat gained; and steam condensing at $100\ ^\circ\text{C}$ gives $L_v$ plus $mc\Delta T$ as the condensed water cools.

The temperature of a black body is raised from $27\ ^\circ\text{C}$ to $327\ ^\circ\text{C}$. The power it radiates becomes

Exercises

Unless told otherwise use $c_\text{w}=4200$, $c_\text{ice}=2100\ \text{J kg}^{-1}\text{K}^{-1}$, $L_f=3.36\times10^5\ \text{J/kg}$, $L_v=2.26\times10^6\ \text{J/kg}$, $\sigma=5.67\times10^{-8}\ \text{W m}^{-2}\text{K}^{-4}$, $b=2.9\times10^{-3}\ \text{m K}$, and assume no heat is lost to the surroundings.

I
Temperature and thermal expansion.
  • 1 Normal body temperature is $98.6\ ^\circ\text{F}$. Express it in $^\circ\text{C}$ and in kelvin.
  • 2 At what temperature do the Celsius and Fahrenheit scales give the same reading?
  • 3 A faulty thermometer reads $5\ ^\circ\text{C}$ in melting ice and $95\ ^\circ\text{C}$ in steam at $1\ \text{atm}$, and its scale is uniform. What is the true temperature when it reads $41\ ^\circ\text{C}$?
  • 4 A copper wire ($\alpha=1.7\times10^{-5}\ \text{K}^{-1}$) is $2.50\ \text{m}$ long at $20\ ^\circ\text{C}$. Find its increase in length at $120\ ^\circ\text{C}$.
  • 5 A brass sheet ($\alpha=1.9\times10^{-5}\ \text{K}^{-1}$) measures $40\ \text{cm}\times25\ \text{cm}$. Find the increase in its area when it is heated by $80\ \text{K}$.
  • 6 The density of mercury is $13\,600\ \text{kg/m}^3$ at $0\ ^\circ\text{C}$ and $\gamma=1.8\times10^{-4}\ \text{K}^{-1}$. Find its density at $100\ ^\circ\text{C}$.
  • 7 A glass flask ($\alpha_\text{glass}=9\times10^{-6}\ \text{K}^{-1}$) is filled to the brim with $250\ \text{cm}^3$ of mercury at $20\ ^\circ\text{C}$. How much mercury overflows when both are heated to $80\ ^\circ\text{C}$?
  • 8 A steel rod ($Y=2.0\times10^{11}\ \text{Pa}$, $\alpha=1.2\times10^{-5}\ \text{K}^{-1}$) of cross-section $2.0\ \text{cm}^2$ is clamped between rigid walls without stress and then heated by $50\ \text{K}$. Find the stress in it and the force on each wall.
  • 9 A steel tape ($\alpha=1.2\times10^{-5}\ \text{K}^{-1}$) is correct at $20\ ^\circ\text{C}$. On a day at $45\ ^\circ\text{C}$ it gives a rod's length as $2.4000\ \text{m}$. Find the true length and the error.
  • 10 A clock with a steel pendulum ($\alpha=1.2\times10^{-5}\ \text{K}^{-1}$) keeps correct time at $20\ ^\circ\text{C}$. How many seconds does it lose or gain per day at $40\ ^\circ\text{C}$?
1 $t_C=\tfrac59(98.6-32)=37.0\ ^\circ\text{C}$; $T=37.0+273.15=310\ \text{K}$.
2 $t=\tfrac95t+32$ gives $t=-40$: $-40\ ^\circ\text{C}=-40\ ^\circ\text{F}$.
3 $\dfrac{41-5}{95-5}=\dfrac{t}{100}$, so $t=40\ ^\circ\text{C}$.
4 $\Delta L=2.50\times1.7\times10^{-5}\times100=4.25\times10^{-3}\ \text{m}=4.25\ \text{mm}$.
5 $\Delta A=2\alpha A\Delta T=2\times1.9\times10^{-5}\times0.10\times80=3.04\times10^{-4}\ \text{m}^2=3.04\ \text{cm}^2$.
6 $\rho=\dfrac{13\,600}{1+1.8\times10^{-4}\times100}=\dfrac{13\,600}{1.018}=1.336\times10^4\ \text{kg/m}^3$.
7 $\gamma_\text{glass}=3\alpha=2.7\times10^{-5}\ \text{K}^{-1}$. Overflow $=V(\gamma_\text{Hg}-\gamma_\text{glass})\Delta T=250\times1.53\times10^{-4}\times60=2.30\ \text{cm}^3$.
8 Stress $=Y\alpha\Delta T=2.0\times10^{11}\times1.2\times10^{-5}\times50=1.2\times10^8\ \text{Pa}$ (compressive); $F=1.2\times10^8\times2.0\times10^{-4}=2.4\times10^4\ \text{N}$.
9 The warm tape's markings are spread out, so it reads too little: true length $=2.4000(1+1.2\times10^{-5}\times25)=2.4007\ \text{m}$; the error is $0.72\ \text{mm}$ (reading too small).
10 Loses $\tfrac12\alpha\Delta\theta\times86\,400=\tfrac12\times1.2\times10^{-5}\times20\times86\,400=10.4\ \text{s}$ per day.
II
Specific heat capacity, calorimetry and latent heat.
  • 1 Find the heat needed to raise $2.0\ \text{kg}$ of water from $15\ ^\circ\text{C}$ to $75\ ^\circ\text{C}$, and the time a $2.0\ \text{kW}$ kettle takes to supply it.
  • 2 Find the heat capacity and the water equivalent of a $0.50\ \text{kg}$ aluminium pan ($c=900\ \text{J kg}^{-1}\text{K}^{-1}$).
  • 3 $0.30\ \text{kg}$ of water at $80\ ^\circ\text{C}$ is mixed with $0.50\ \text{kg}$ of water at $20\ ^\circ\text{C}$. Find the final temperature.
  • 4 A $0.40\ \text{kg}$ iron ball ($c=460\ \text{J kg}^{-1}\text{K}^{-1}$) at $150\ ^\circ\text{C}$ is dropped into $1.0\ \text{kg}$ of water at $20\ ^\circ\text{C}$. Find the final temperature.
  • 5 Find the heat needed to turn $0.20\ \text{kg}$ of ice at $-10\ ^\circ\text{C}$ into water at $50\ ^\circ\text{C}$.
  • 6 Find the heat released when $50\ \text{g}$ of steam at $100\ ^\circ\text{C}$ condenses and the water formed cools to $40\ ^\circ\text{C}$.
  • 7 $20\ \text{g}$ of steam at $100\ ^\circ\text{C}$ is passed into $500\ \text{g}$ of water at $20\ ^\circ\text{C}$ until it has all condensed. Find the final temperature.
  • 8 A $1.5\ \text{kW}$ heater supplies heat at a steady rate to $1.0\ \text{kg}$ of ice at $0\ ^\circ\text{C}$. Sketch the temperature–time graph up to the moment all the water has boiled away, and find the duration of each stage.
  • 9 A $120\ \text{g}$ copper calorimeter ($c=390\ \text{J kg}^{-1}\text{K}^{-1}$) contains $150\ \text{g}$ of a liquid at $20\ ^\circ\text{C}$. When $80\ \text{g}$ of aluminium ($c=900\ \text{J kg}^{-1}\text{K}^{-1}$) at $100\ ^\circ\text{C}$ is dropped in, the final temperature is $32\ ^\circ\text{C}$. Find the specific heat capacity of the liquid.
1 $Q=2.0\times4200\times60=5.04\times10^5\ \text{J}$; $t=\dfrac{5.04\times10^5}{2000}=252\ \text{s}$ (about $4.2$ minutes).
2 $C=mc=450\ \text{J/K}$; water equivalent $\dfrac{450}{4200}=0.107\ \text{kg}=107\ \text{g}$.
3 Same substance: $T_f=\dfrac{0.30\times80+0.50\times20}{0.80}=42.5\ ^\circ\text{C}$.
4 $T_f=\dfrac{0.40\times460\times150+1.0\times4200\times20}{0.40\times460+4200}=\dfrac{111\,600}{4384}=25.5\ ^\circ\text{C}$.
5 $Q=0.20\left(2100\times10+3.36\times10^5+4200\times50\right)=0.20\times5.67\times10^5=1.134\times10^5\ \text{J}=113\ \text{kJ}$.
6 $Q=0.050\left(2.26\times10^6+4200\times60\right)=0.050\times2.512\times10^6=1.26\times10^5\ \text{J}$.
7 Heat lost by steam $=0.020\left[2.26\times10^6+4200(100-T)\right]$; gained by water $=0.50\times4200(T-20)$. So $45\,200+84(100-T)=2100(T-20)$, giving $2184\,T=95\,600$ and $T=43.8\ ^\circ\text{C}$.
8 Plateau at $0\ ^\circ\text{C}$: $\dfrac{3.36\times10^5}{1500}=224\ \text{s}$; straight rise to $100\ ^\circ\text{C}$: $\dfrac{4200\times100}{1500}=280\ \text{s}$; plateau at $100\ ^\circ\text{C}$: $\dfrac{2.26\times10^6}{1500}=1507\ \text{s}$ (about 25 minutes) — the boiling plateau is almost seven times the melting one.
9 Heat lost by aluminium $=0.080\times900\times68=4896\ \text{J}$. Gained: $(0.120\times390+0.150\,c)\times12=561.6+1.8\,c$. So $c=\dfrac{4896-561.6}{1.8}=2.41\times10^3\ \text{J kg}^{-1}\text{K}^{-1}$.
III
Conduction.
  • 1 A copper rod ($k=400\ \text{W m}^{-1}\text{K}^{-1}$) $1.0\ \text{m}$ long with cross-section $2.0\ \text{cm}^2$ and insulated sides has its ends at $100\ ^\circ\text{C}$ and $0\ ^\circ\text{C}$. Find the heat current in the steady state.
  • 2 For the rod in part 1 find the thermal resistance, the temperature gradient, and the temperature $30\ \text{cm}$ from the hot end.
  • 3 A glass window ($k=0.80\ \text{W m}^{-1}\text{K}^{-1}$) $1.5\ \text{m}\times1.0\ \text{m}$ and $4.0\ \text{mm}$ thick has its inner surface at $18\ ^\circ\text{C}$ and its outer surface at $6\ ^\circ\text{C}$. Find the rate of heat loss.
  • 4 A wall of area $10\ \text{m}^2$ is $20\ \text{cm}$ of brick ($k=0.80$) lined on the outside with $5.0\ \text{cm}$ of foam ($k=0.040\ \text{W m}^{-1}\text{K}^{-1}$). The inner face is at $25\ ^\circ\text{C}$ and the outer face at $5\ ^\circ\text{C}$. Find the heat current and the temperature of the brick–foam interface.
  • 5 Two slabs of equal area and thickness, with conductivities $k$ and $3k$, are in series. The outer face of the $k$ slab is at $100\ ^\circ\text{C}$ and that of the $3k$ slab at $20\ ^\circ\text{C}$. Find the interface temperature.
  • 6 Find the equivalent conductivity of two layers of equal thickness with $k_1=0.20$ and $k_2=0.60\ \text{W m}^{-1}\text{K}^{-1}$ (a) in series, (b) side by side with equal areas.
  • 7 Ice $5.0\ \text{cm}$ thick has formed on a pond; the air above is at $-10\ ^\circ\text{C}$. Taking $k_\text{ice}=2.2\ \text{W m}^{-1}\text{K}^{-1}$ and $\rho_\text{ice}=920\ \text{kg/m}^3$, find the rate at which the ice is thickening (in mm per hour) and the time for it to grow to $10\ \text{cm}$.
  • 8 Three identical rods meet at a common junction. Their free ends are held at $90\ ^\circ\text{C}$, $60\ ^\circ\text{C}$ and $0\ ^\circ\text{C}$. Find the junction temperature in the steady state and the direction of heat flow in each rod.
1 $H=\dfrac{kA\Delta T}{L}=\dfrac{400\times2.0\times10^{-4}\times100}{1.0}=8.0\ \text{W}$.
2 $R=\dfrac{L}{kA}=12.5\ \text{K/W}$; gradient $100\ \text{K/m}$; the temperature falls linearly, so $30\ \text{cm}$ from the hot end it is $70\ ^\circ\text{C}$.
3 $H=\dfrac{0.80\times1.5\times12}{0.0040}=3.6\times10^3\ \text{W}$ — single glazing is a large leak.
4 $R_\text{brick}=\dfrac{0.20}{0.80\times10}=0.025\ \text{K/W}$, $R_\text{foam}=\dfrac{0.050}{0.040\times10}=0.125\ \text{K/W}$. $H=\dfrac{20}{0.150}=133\ \text{W}$. Interface: $25-133.3\times0.025=21.7\ ^\circ\text{C}$ — the thin foam takes $83\%$ of the drop.
5 $k(100-T)=3k(T-20)$ gives $4T=160$, $T=40\ ^\circ\text{C}$.
6 (a) $k_\text{eq}=\dfrac{2\times0.20\times0.60}{0.80}=0.30\ \text{W m}^{-1}\text{K}^{-1}$; (b) $\dfrac{0.20+0.60}{2}=0.40\ \text{W m}^{-1}\text{K}^{-1}$.
7 $\dfrac{dx}{dt}=\dfrac{k\theta}{\rho L_fx}=\dfrac{2.2\times10}{920\times3.36\times10^5\times0.050}=1.42\times10^{-6}\ \text{m/s}=5.1\ \text{mm/h}$. Time: $t=\dfrac{\rho L_f}{2k\theta}(x_2^2-x_1^2)=\dfrac{920\times3.36\times10^5}{44}\times(0.0100-0.0025)=5.27\times10^4\ \text{s}=14.6\ \text{h}$.
8 Equal rods have equal resistances; the net heat into the junction is zero: $(90-T)+(60-T)+(0-T)=0$, so $T=50\ ^\circ\text{C}$. Heat flows into the junction from the $90\ ^\circ\text{C}$ and $60\ ^\circ\text{C}$ ends and out to the $0\ ^\circ\text{C}$ end.
IV
Convection, radiation and mixed problems.
  • 1 Explain why a breeze blows from the sea towards the land on a sunny afternoon, and the other way late at night.
  • 2 For each feature of a vacuum flask — the vacuum, the silvered walls, the stopper — name the mode(s) of heat transfer it reduces.
  • 3 The temperature of a black body is raised from $400\ \text{K}$ to $800\ \text{K}$. By what factor does its radiated power increase, and what is its new peak wavelength?
  • 4 The Sun's spectrum peaks at about $500\ \text{nm}$. Estimate the temperature of its surface.
  • 5 A lamp filament of surface area $0.50\ \text{cm}^2$ and emissivity $0.40$ runs at $2500\ \text{K}$. Find the power it radiates.
  • 6 A black body in surroundings at $27\ ^\circ\text{C}$ is first at $127\ ^\circ\text{C}$ and then at $227\ ^\circ\text{C}$. Find the ratio of its net rates of radiative heat loss at the two temperatures (higher to lower).
  • 7 Two solid spheres of the same material and surface finish, of radii $r$ and $2r$, are at the same high temperature in cold surroundings. Find the ratio of their initial rates of fall of temperature (small to large).
  • 8 The aluminium base ($k=200\ \text{W m}^{-1}\text{K}^{-1}$) of a kettle has area $0.020\ \text{m}^2$ and thickness $2.0\ \text{mm}$. A heater below it delivers $2.0\ \text{kW}$ steadily into the boiling water. Find the temperature of the underside of the base and the rate at which water boils away.
1 Land has a much smaller specific heat capacity than water, so by day it heats up faster; air over the land expands, rises, and cooler air from over the sea flows in (sea breeze). At night the land cools faster, the air over the warmer sea rises, and the surface flow reverses (land breeze). Both are natural convection.
2 Vacuum: conduction and convection (no medium). Silvered walls: radiation (high reflectivity, low emissivity). Stopper: convection and conduction through the mouth.
3 Power $\times2^4=16$. $\lambda_m=\dfrac{2.9\times10^{-3}}{800}=3.63\times10^{-6}\ \text{m}=3.63\ \mu\text{m}$ (it was $7.25\ \mu\text{m}$).
4 $T=\dfrac{b}{\lambda_m}=\dfrac{2.9\times10^{-3}}{5.0\times10^{-7}}=5.8\times10^3\ \text{K}$.
5 $P=e\sigma AT^4=0.40\times5.67\times10^{-8}\times5.0\times10^{-5}\times(2500)^4=44.3\ \text{W}$.
6 In kelvin: $\dfrac{500^4-300^4}{400^4-300^4}=\dfrac{6.25\times10^{10}-0.81\times10^{10}}{2.56\times10^{10}-0.81\times10^{10}}=\dfrac{5.44}{1.75}=3.11$.
7 Rate of fall $\dfrac{dT}{dt}=\dfrac{P}{mc}=\dfrac{e\sigma(4\pi r^2)T^4}{\rho\,\tfrac43\pi r^3c}\propto\dfrac1r$. Small sphere : large sphere $=2:1$ — small bodies cool faster.
8 $\Delta T=\dfrac{HL}{kA}=\dfrac{2000\times0.0020}{200\times0.020}=1.0\ \text{K}$, so the underside is at $101\ ^\circ\text{C}$. Boiling rate $=\dfrac{2000}{2.26\times10^6}=8.85\times10^{-4}\ \text{kg/s}\approx0.89\ \text{g/s}$.
🎯 Exam corner JEE Main · MCQJEE Main · Numerical

E1. JEE Main · MCQ A steel rod ($\alpha=1.2\times10^{-5}\ \text{K}^{-1}$) and a brass rod ($\alpha=1.8\times10^{-5}\ \text{K}^{-1}$) are to be cut so that the steel rod is always $10\ \text{cm}$ longer than the brass rod, at every temperature. Their lengths must be (A) steel $20\ \text{cm}$, brass $10\ \text{cm}$ (B) steel $18\ \text{cm}$, brass $8\ \text{cm}$ (C) steel $30\ \text{cm}$, brass $20\ \text{cm}$ (D) steel $20\ \text{cm}$, brass $30\ \text{cm}$

Condition The difference stays fixed only if both rods expand by the same amount: $L_s\alpha_s\Delta T=L_b\alpha_b\Delta T$, so $\dfrac{L_s}{L_b}=\dfrac{\alpha_b}{\alpha_s}=\dfrac{1.8}{1.2}=\dfrac32$.
Solve With $L_s-L_b=10\ \text{cm}$: $L_b=20\ \text{cm}$, $L_s=30\ \text{cm}$.
Answer (C).
⏱ Shortcut Lengths are inversely proportional to the $\alpha$'s, so steel (smaller $\alpha$) is the longer rod — this kills (D) at once; then $3:2$ with a difference of $10$ gives $30$ and $20$.

E2. JEE Main · Numerical $100\ \text{g}$ of ice at $0\ ^\circ\text{C}$ is added to $300\ \text{g}$ of water at $60\ ^\circ\text{C}$ in a vessel of negligible heat capacity. Take the specific heat of water as $4.2\ \text{J g}^{-1}\text{K}^{-1}$ and the latent heat of fusion of ice as $336\ \text{J/g}$. Find the final temperature of the mixture in $^\circ\text{C}$. Give the answer to the nearest integer.

Test Melting all the ice needs $100\times336=33\,600\ \text{J}$; the water can give $300\times4.2\times60=75\,600\ \text{J}$ in cooling to $0\ ^\circ\text{C}$. So all the ice melts.
Balance The surplus $75\,600-33\,600=42\,000\ \text{J}$ warms all $400\ \text{g}$ from $0\ ^\circ\text{C}$: $T_f=\dfrac{42\,000}{400\times4.2}=25\ ^\circ\text{C}$.
Answer $25$.
⏱ Shortcut Think of the ice as water at $-\dfrac{L_f}{c}=-80\ ^\circ\text{C}$: $T_f=\dfrac{300\times60+100\times(-80)}{400}=25\ ^\circ\text{C}$ (valid only because the answer came out positive).

E3. JEE Main · MCQ Two identical metal rods, joined end to end between two heat reservoirs, conduct a certain quantity of heat in $12$ minutes. If the same two rods are instead placed side by side between the same reservoirs, the same quantity of heat is conducted in (A) $6$ minutes (B) $3$ minutes (C) $24$ minutes (D) $48$ minutes

Resistances Each rod has resistance $R$. End to end: $R_\text{eq}=2R$. Side by side: $R_\text{eq}=\tfrac R2$ — four times smaller.
Time $H=\Delta T/R_\text{eq}$ becomes four times larger, so the same heat flows in a quarter of the time: $12/4=3$ minutes.
Answer (B).
⏱ Shortcut Series → parallel for two equal resistances is always a factor $4$. Option (A) comes from doubling only the area and forgetting that the length is halved too.

E4. JEE Main · Numerical A brass wire of cross-section $1.0\ \text{mm}^2$ is stretched between two rigid supports with negligible tension at $40\ ^\circ\text{C}$. For brass $Y=0.90\times10^{11}\ \text{N/m}^2$ and $\alpha=2.0\times10^{-5}\ \text{K}^{-1}$. Find the tension (in N) in the wire when it is cooled to $-10\ ^\circ\text{C}$. Give the answer to the nearest integer.

Idea The supports stop the wire from contracting by $\alpha L\Delta T$, so it is stretched by a strain $\alpha\Delta T$ (Result 7.24): $F=YA\alpha\Delta T$.
Value $F=0.90\times10^{11}\times1.0\times10^{-6}\times2.0\times10^{-5}\times50=90\ \text{N}$.
Answer $90$.
⏱ Shortcut The length of the wire is not given because it is not needed — thermal stress $Y\alpha\Delta T$ is independent of length.

E5. JEE Main · MCQ The wavelength at which a black body radiates most strongly shifts from $2.0\ \mu\text{m}$ to $1.5\ \mu\text{m}$ when its temperature is raised. If it radiated power $P$ at first, it now radiates (A) $\tfrac43P$ (B) $\tfrac{16}9P$ (C) $\tfrac{64}{27}P$ (D) $\tfrac{256}{81}P$

Wien $\lambda_mT=b$, so $\dfrac{T_2}{T_1}=\dfrac{\lambda_1}{\lambda_2}=\dfrac{2.0}{1.5}=\dfrac43$.
Stefan $\dfrac{P_2}{P_1}=\left(\dfrac{T_2}{T_1}\right)^4=\left(\dfrac43\right)^4=\dfrac{256}{81}\approx3.16$.
Answer (D).
⏱ Shortcut $P\propto T^4\propto\lambda_m^{-4}$: raise the inverse wavelength ratio to the fourth power. (A), (B), (C) are the first, second and third powers.

E6. JEE Main · Numerical A pendulum clock whose pendulum rod has $\alpha=2.0\times10^{-5}\ \text{K}^{-1}$ keeps correct time at $25\ ^\circ\text{C}$. Find the time (in seconds) it loses in one day when the temperature is $45\ ^\circ\text{C}$. Give the answer to the nearest integer.

Idea $T\propto\sqrt\ell$, so $\dfrac{\Delta T}{T}=\tfrac12\alpha\Delta\theta=\tfrac12\times2.0\times10^{-5}\times20=2.0\times10^{-4}$.
Per day Time lost $=2.0\times10^{-4}\times86\,400=17.28\ \text{s}$.
Answer $17$.
⏱ Shortcut Remember the half: forgetting it gives $35\ \text{s}$, the most common wrong entry.
🔬 Research–Teaching NexusResearch-tutored · optional, about 60 minutes

Research question. Which everyday material makes the best insulating lining for a cool box — and can you measure its thermal conductivity using nothing more than melting ice and a kitchen scale?

Why it matters. Vaccines, insulin and blood samples travel to clinics in hot countries in insulated boxes; farmers and fishing communities keep produce fresh with ice boxes; and the insulation of buildings decides a large share of the world's energy use for heating and cooling. Insulation is rated by its thermal resistance, exactly the $R=L/(kA)$ of Definition 7.21. Melting ice is a beautiful heat meter: every $3.36\times10^5\ \text{J}$ that leaks in melts exactly one kilogram, at a temperature fixed at $0\ ^\circ\text{C}$.

What to do.

  1. Make three or four identical small boxes (shoe boxes or cartons), each lined on all sides with a different material of known thickness: newspaper, cloth, corrugated cardboard, polystyrene sheet. Measure the inside area $A$ of the lining and its thickness $L$.
  2. Put the same mass of ice cubes (about $300\ \text{g}$, weighed) in a plastic bag in each box, close the boxes, and leave them in the same room. Record the room temperature.
  3. Every $30$ minutes, pour off and weigh the meltwater (or weigh the remaining ice). Plot melted mass against time for each box; the slope is $dm/dt$.
  4. In the steady state, heat leaking in $H=L_f\,\dfrac{dm}{dt}$. With the inside at $0\ ^\circ\text{C}$ and the outside at room temperature $T_r$, estimate $k=\dfrac{HL}{A\,T_r}$ for each lining.
  5. Compare your values with published conductivities and rank the materials.

Tools: Kitchen scale (1 g resolution), ice, plastic bags, boxes, lining materials, ruler, thermometer, clock or phone timer, spreadsheet.

Hand in: A graph of melted mass against time for all boxes, a table of $H$, $R$ and estimated $k$ for each lining, and one paragraph explaining which sources of error (heat entering through the lid seams, the box's own walls, air gaps) push your $k$ values up or down.

Going further. Line one box with two materials in series and test whether the thermal resistances add as Result 7.27 predicts. Or wrap one box in aluminium foil (shiny side out) and see how much radiation matters compared with conduction.

Instructor note: with $300\ \text{g}$ of ice and room temperature near $25$–$30\ ^\circ\text{C}$, boxes lined with $1$–$2\ \text{cm}$ of polystyrene typically lose $10$–$20\ \text{g}$ per half hour, giving $k$ of a few hundredths of $\text{W m}^{-1}\text{K}^{-1}$ — the right order of magnitude, usually somewhat high because of leaks at the seams and the extra resistance of the air films being ignored. Newspaper and cloth come out several times higher. The two-layer test usually supports adding resistances within $20$–$30\%$.

🧪 Self-check quiz

0/5 correct

Q1. An isotropic solid has coefficient of linear expansion $\alpha$. Its coefficient of volume expansion is

Q2. A sample of water is heated steadily from $0\ ^\circ\text{C}$ to $10\ ^\circ\text{C}$. Its volume

Q3. The SI unit of thermal conductivity is

Q4. Two rods of the same length and cross-section, with conductivities $k_1$ and $k_2$, are joined end to end. The single rod of the same total length and area that conducts heat at the same rate has conductivity

Q5. While ice at $0\ ^\circ\text{C}$ is melting, the heat supplied to it