Chapter 4 · Work, Energy and Power

4.2 Potential Energy, Conservative Forces and Power

When a force's work depends only on where a body starts and ends, it has a potential energy $U$ with $F=-dU/dx$; if only such forces do work, $K+U$ stays constant. One energy equation then handles springs, roller coasters, vertical circles and — divided by time — power.

A roller coaster is hauled once to the top of its first hill and then let go. For the next two minutes no motor touches it, yet it dives, climbs, loops and twists, always slower at the high points and faster at the low ones. A child's toy gun stores a push in a squeezed spring and gives it back as the speed of a dart. A hydroelectric dam collects water high in the hills and turns its fall into electrical power for a city. All three are the same story: energy stored by position being traded for energy of motion and back again.

In Section 4.1 we learned to compute the work done by forces and showed that the net work equals the change in kinetic energy. This section sorts forces into two kinds — those whose work can be "stored" and returned (gravity, springs) and those whose work cannot (friction, drag). The first kind have a potential energy, and when only they do work the total mechanical energy is conserved. We then apply this to the motion in a vertical circle that Section 3.4 could only begin, and finish with power, the rate of doing work.

Conservative forces and potential energy

Lift a $2\ \text{kg}$ book from the floor to a shelf $1.5\ \text{m}$ up. Whether you lift it straight up, or carry it round the room first, gravity does the same work on it, $-mgh=-29.4\ \text{J}$ (Section 4.1: only the vertical component of each little step counts, and they add up to $h$). Put it back on the floor by any route and gravity gives back $+29.4\ \text{J}$; round the closed trip, gravity's total work is zero. Now drag the same book across a rough table from one corner to another. The friction work is $-\mu_kmg$ times the length of the path: a longer route costs more, and a round trip costs twice as much — friction never gives anything back.

📘 Definition 4.4 — Conservative and non-conservative forces

A force is conservative if the work it does on a body moving between two points depends only on those two points and not on the path taken. Equivalently, the work it does round any closed path is zero. Gravity, the force of an ideal spring and the electrostatic force are conservative.

A force that does not have this property is non-conservative. Kinetic friction, air resistance and viscous drag are non-conservative: their work depends on the path and is negative round a closed loop. (Forces applied by people, motors or ropes are also treated as non-conservative "external" forces.)

Because a conservative force's work depends only on the end points, we can assign to every position a number — the potential energy — so that the work is simply the drop in that number. The choice of the position where $U=0$ (the reference level) is ours; only differences in $U$ have physical meaning.

📘 Definition 4.5 — Potential energy

For a conservative force $\mathbf{F}$, the potential energy $U$ is defined (up to an additive constant) by

$$\Delta U=U_B-U_A=-W_{A\to B}=-\int_A^B\mathbf{F}\cdot d\mathbf{r}.$$

The work done by a conservative force equals the decrease in potential energy. Near the Earth's surface, with the reference level at height $0$, the gravitational potential energy of a mass $m$ at height $h$ is $U=mgh$ (valid while $h$ is small compared with the Earth's radius, so that $g$ is constant).

Run the definition backwards. For a small displacement $dx$ along the $x$-axis, $dU=-F\,dx$, so the force is the negative slope of the potential-energy graph:

📐 Result 4.5 — Force from potential energy; equilibrium

For a conservative force along $x$, $\qquad F(x)=-\dfrac{dU}{dx}.$

The force points "downhill" on the $U$–$x$ graph. A body is in equilibrium where $F=0$, i.e. where $\dfrac{dU}{dx}=0$:

  • at a minimum of $U$ $\left(\dfrac{d^2U}{dx^2}\gt0\right)$ the equilibrium is stable — a small displacement brings a force back towards it;
  • at a maximum of $U$ $\left(\dfrac{d^2U}{dx^2}\lt0\right)$ it is unstable — a small displacement brings a force pushing it further away;
  • where $U$ is constant over a range it is neutral.

A marble resting at the bottom of a bowl is in stable equilibrium, one balanced on top of an upturned bowl is in unstable equilibrium, and one on a flat table is in neutral equilibrium. The same graph also shows where a body can go: with total energy $E$, it can only be where $U(x)\le E$, because $K=E-U$ cannot be negative. Points where $U=E$ are turning points, where the body momentarily stops and turns back.

✏️ Example 1 — Gravity keeps no memory of the path; friction does
A $2.0\ \text{kg}$ box is moved from a point $A$ on the floor of a room to a point $B$, $3.0\ \text{m}$ east and $4.0\ \text{m}$ north of $A$. (a) It is first lifted and carried; find the work done by gravity if it is carried along any path and placed at a point $1.5\ \text{m}$ above $B$. (b) It is instead dragged along the rough floor ($\mu_k=0.30$), either straight from $A$ to $B$ or east and then north. Find the work done by friction for each route, and for a round trip $A\to B\to A$ by the straight route.
(a) Gravity depends only on the change of height: $W_\text{grav}=-mg\,\Delta h=-2.0\times9.8\times1.5=-29.4\ \text{J}$ — the same for every path. Its potential energy rises by $29.4\ \text{J}$.
(b) Straight $N=mg$, friction $\mu_kmg=5.88\ \text{N}$ along the whole path of length $5.0\ \text{m}$: $W_f=-5.88\times5.0=-29.4\ \text{J}$.
(b) Two legs Path length $3.0+4.0=7.0\ \text{m}$: $W_f=-5.88\times7.0=-41.2\ \text{J}$ — different, so friction is not conservative.
Round trip Friction opposes the motion on both legs: $W_f=-29.4-29.4=-58.8\ \text{J}\neq0$. Gravity's work round any closed trip is zero.
✏️ Example 2 — Reading a potential-energy function
A particle moving along the $x$-axis has potential energy $U(x)=x^3-6x^2+9x$ (in joules, $x$ in metres). (a) Find the force on it at $x=2\ \text{m}$. (b) Find its equilibrium positions and say whether each is stable or unstable. (c) The particle is at $x=3\ \text{m}$ with kinetic energy $3\ \text{J}$. Can it reach $x=1\ \text{m}$?
Find the force at $x=2\ \text{m}$ (sign included) before you open the solution:
(a) $F=-\dfrac{dU}{dx}=-(3x^2-12x+9)$. At $x=2$: $F=-(12-24+9)=+3\ \text{N}$, i.e. $3\ \text{N}$ in the $+x$ direction.
(b) $\dfrac{dU}{dx}=3(x-1)(x-3)=0$ at $x=1\ \text{m}$ and $x=3\ \text{m}$. $\dfrac{d^2U}{dx^2}=6x-12$: at $x=1$ it is $-6\lt0$ (maximum of $U$, unstable); at $x=3$ it is $+6\gt0$ (minimum, stable).
(c) $E=U(3)+K=0+3=3\ \text{J}$. But $U(1)=1-6+9=4\ \text{J}\gt E$, so $x=1$ is out of reach: the particle turns back before getting there.
Check At $x=2$, between the hill at $x=1$ and the valley at $x=3$, the force should push towards the valley, i.e. along $+x$ ✓.

A particle has potential energy $U(x)=5x^2$ (in J, $x$ in m). The force on it at $x=2\ \text{m}$ is

Spring potential energy and conservation of mechanical energy

From Result 4.3, the spring force does work $-\tfrac12k\left(x_2^2-x_1^2\right)$ when its extension changes from $x_1$ to $x_2$ — a quantity that depends only on the end points. So the spring force is conservative, and comparing with Definition 4.5 gives its potential energy.

📐 Result 4.6 — Potential energy of a spring

An ideal spring of spring constant $k$, stretched or compressed by $x$ from its natural length, stores elastic potential energy

$$U=\tfrac12kx^2 \qquad(U=0 \text{ at the natural length}).$$

$U$ is the same for a stretch and a compression of the same size, and it grows as the square of $x$. Check: $F=-\dfrac{dU}{dx}=-kx$, Hooke's law.

Now put the two ideas together. Split the net work on a body into the work done by conservative forces, $W_c=-\Delta U$, and the work done by all other forces, $W_\text{nc}$. The work–energy theorem says $W_c+W_\text{nc}=\Delta K$, so

$$W_\text{nc}=\Delta K+\Delta U=\Delta(K+U).$$
📘 Definition 4.6 — Mechanical energy

The mechanical energy of a body (or system) is the sum of its kinetic energy and the potential energies of all the conservative forces acting: $E=K+U$, e.g. $E=\tfrac12mv^2+mgh+\tfrac12kx^2$.

📐 Law 4.7 — Conservation of mechanical energy

If only conservative forces do work on a body (any other forces present, such as a normal force or a string tension perpendicular to the motion, do no work), its mechanical energy is constant:

$$K_i+U_i=K_f+U_f .$$

The law holds in an inertial frame, for any path and for forces that vary along the path.

📐 Result 4.8 — Work done by non-conservative forces

In general, the work done by the non-conservative forces equals the change in mechanical energy:

$$W_\text{nc}=(K_f+U_f)-(K_i+U_i).$$

Kinetic friction acting over a path length $s$ does $W_\text{nc}=-f_ks$; the lost mechanical energy $f_ks$ appears as thermal energy of the surfaces. Total energy (mechanical + thermal + every other form) is always conserved.

A swinging pendulum shows the law at work: the string's tension is always perpendicular to the bob's velocity, so it does no work, and $\tfrac12mv^2+mgh$ stays fixed. A stone thrown from a cliff reaches the ground with the same speed whatever the direction of the throw, $v=\sqrt{u^2+2gH}$. And a smooth roller-coaster car passes every point of equal height with equal speed.

🧭 Problem-solving strategy — The energy method
  1. Pick the two states (initial and final) and a reference level for gravitational $U$ (any convenient height — often the lowest point).
  2. List the forces. Conservative ones (gravity, springs) go into $U$; check whether any other force does work.
  3. If none does: $K_i+U_i=K_f+U_f$. If friction or an applied force does work, use $K_i+U_i+W_\text{nc}=K_f+U_f$, with $W_f=-\mu_kN\,s$.
  4. For springs, measure $x$ from the natural length; at maximum compression the speed is zero (or, for two moving bodies, the relative speed is zero).
  5. If the question also asks for a force (tension, normal force), use Newton's second law at that point, with the speed from step 3.
✏️ Example 3 — Block meets spring
A $0.50\ \text{kg}$ block slides at $3.0\ \text{m/s}$ on a smooth horizontal floor towards a light spring ($k=200\ \text{N/m}$) fixed to a wall. Find (a) the maximum compression of the spring, (b) the speed of the block when the compression is $9.0\ \text{cm}$, (c) the speed with which the block leaves the spring.
Energy Only the spring does work (gravity and the normal force are vertical): $\tfrac12mu^2=\tfrac12mv^2+\tfrac12kx^2$. Initial energy $\tfrac12(0.50)(9.0)=2.25\ \text{J}$.
(a) At maximum compression $v=0$: $\tfrac12(200)x^2=2.25$, $x=\sqrt{0.0225}=0.15\ \text{m}=15\ \text{cm}$. (Or $x=u\sqrt{m/k}=3.0\times0.050$.)
(b) $v^2=u^2-\dfrac{k}{m}x^2=9.0-400\times0.0081=5.76$, so $v=2.4\ \text{m/s}$.
(c) When the spring regains its natural length its energy is back to zero: the block leaves at $3.0\ \text{m/s}$, now moving away.
Check At $9\ \text{cm}$ (60% of the maximum) the spring holds $0.36$ of the energy, $0.81\ \text{J}$; the block keeps $1.44\ \text{J}=\tfrac12(0.50)(2.4)^2$ ✓.
✏️ Example 4 — Ramp, rough floor, spring
A $1.0\ \text{kg}$ block is released from rest at the top of a smooth curved ramp $2.0\ \text{m}$ high. At the bottom it moves onto a rough horizontal floor ($\mu_k=0.25$). A light spring ($k=400\ \text{N/m}$) is fixed $3.0\ \text{m}$ from the foot of the ramp, along the floor. Find (a) the speed of the block when it reaches the spring, (b) the maximum compression of the spring. (c) How far would the block slide on the floor if the spring were removed (and the floor were long enough)?
Find the maximum compression (b) before you open the solution:
Ramp Smooth, so energy is conserved: at the bottom $K=mgh=1.0\times9.8\times2.0=19.6\ \text{J}$.
(a) Friction $\mu_kmg=2.45\ \text{N}$ over $3.0\ \text{m}$ does $-7.35\ \text{J}$: $K=12.25\ \text{J}$, $v=\sqrt{2\times12.25/1.0}=4.95\ \text{m/s}$.
(b) Friction keeps acting while the spring is compressed by $x$: $12.25-2.45x=\tfrac12(400)x^2$, i.e. $200x^2+2.45x-12.25=0$. The positive root is $x=\dfrac{-2.45+\sqrt{2.45^2+4\times200\times12.25}}{400}=\dfrac{-2.45+99.03}{400}=0.241\ \text{m}$.
(c) All of $mgh$ goes into friction: $\mu_kmg\,s=mgh$, so $s=\dfrac{h}{\mu_k}=\dfrac{2.0}{0.25}=8.0\ \text{m}$ — independent of the mass and of $g$.
Check Without friction during the compression, $x=\sqrt{2\times12.25/400}=0.247\ \text{m}$; friction trims it slightly, as expected.

In the widget set $k=100\ \text{N/m}$, release stretch $x_0=20\ \text{cm}$ and $\mu_k=0.10$ (the block is $1.0\ \text{kg}$). How far past the natural length, on the other side, does the block get before it first turns back?

With $k=100\ \text{N/m}$, $x_0=20\ \text{cm}$, $\mu_k=0.10$ the readouts show stored at release $2\ \text{J}$, greatest speed $1.9\ \text{m/s}$ and first turning point $18\ \text{cm}$ on the far side. Energy: $\tfrac12kx_0^2-\tfrac12kx_1^2=\mu_kmg(x_0+x_1)$ gives $x_1=x_0-\dfrac{2\mu_kmg}{k}=20-1.96=18.0\ \text{cm}$ — every half-swing loses the same $1.96\ \text{cm}$ of amplitude. The fastest point is not at $x=0$ but at $x=\mu_kmg/k=0.98\ \text{cm}$, where the spring force just balances friction. Set $\mu_k=0$ and the swing returns to $20\ \text{cm}$ every time.
Interactive 1 — Spring Energy: Conserved or Lost to Friction?

A $1.0\ \text{kg}$ block on a spring is pulled out by $x_0$ and released. The curve is the spring's potential energy $U=\tfrac12kx^2$; the horizontal line is the block's mechanical energy $E=K+U$, and the gap between them at the block's position is its kinetic energy. Press Play. With $\mu_k=0$ the line stays put; with friction it steps down every swing and the lost energy piles up as heat (bars on the right).

100 N/m20 cm0.10
stored at release—
greatest speed—
first turning point—
heat so far—

A spring stores $2.0\ \text{J}$ when stretched by $4.0\ \text{cm}$. How much energy does it store when stretched by $8.0\ \text{cm}$?

Motion in a vertical circle

Whirl a small stone on a string of length $r$ in a vertical circle. Two forces act: the tension $T$, always along the string towards the centre and so always perpendicular to the velocity (it does no work), and gravity, which slows the stone on the way up and speeds it up on the way down. Energy conservation therefore gives the speed at every point, and Newton's second law along the string gives the tension.

Let the stone have speed $u$ at the lowest point, and let $\theta$ be the angle of the string from the downward vertical. At angle $\theta$ the stone is $r(1-\cos\theta)$ above the bottom, so

$$v^2=u^2-2gr(1-\cos\theta).$$

Along the string, towards the centre, the net force is $T-mg\cos\theta$ (the radial component of the weight points away from the centre when the stone is below the horizontal), and it must equal $mv^2/r$:

$$T=\frac{mv^2}{r}+mg\cos\theta=\frac{m}{r}\left(u^2-2gr+3gr\cos\theta\right).$$

The tension is largest at the bottom ($\theta=0$) and smallest at the top ($\theta=180^\circ$). A string can only pull: if $T$ would have to become negative, the string goes slack and the stone leaves the circle as a projectile.

📐 Result 4.9 — Motion in a vertical circle (string of length $r$, speed $u$ at the bottom)
  • $T_\text{bottom}=m\left(\dfrac{u^2}{r}+g\right)$, $\ T_\text{top}=m\left(\dfrac{v_\text{top}^2}{r}-g\right)$, with $v_\text{top}^2=u^2-4gr$. Hence $T_\text{bottom}-T_\text{top}=6mg$ whenever the stone goes right round.
  • Complete circle if and only if $T_\text{top}\ge0$, i.e. $v_\text{top}\ge\sqrt{gr}$ and $u\ge\sqrt{5gr}$. At the critical speed: $T_\text{top}=0$, $T$ at the horizontal $=3mg$, $T_\text{bottom}=6mg$.
  • If $\sqrt{2gr}\lt u\lt\sqrt{5gr}$, the string goes slack above the horizontal, where $\cos\theta=\dfrac{2gr-u^2}{3gr}$ (negative), and the stone then moves as a projectile.
  • If $u\le\sqrt{2gr}$, the stone never rises above the level of the centre; the string stays taut and the stone swings back and forth like a pendulum.

For a bead on a circular wire, a body on a light rod, or a ball inside a circular tube, the support can push as well as pull, so the only condition is $v_\text{top}\ge0$: $u\ge\sqrt{4gr}=2\sqrt{gr}$. A body on the inside of a smooth loop-the-loop track behaves like the string case ($N\ge0$), so a car released from rest at height $H$ completes a loop of radius $r$ only if $H\ge\tfrac52r$.

Why does a string need $u\ge\sqrt{5gr}$ and not just enough energy to reach the top ($u\ge2\sqrt{gr}$)? Because at the top the stone must still be moving fast enough for gravity alone not to pull it off its circle: $mg\le mv_\text{top}^2/r$. A stone that arrives at the top too slowly has already left the circle before it gets there.

✏️ Example 5 — Round the loop, or not?
A $0.20\ \text{kg}$ ball is whirled in a vertical circle on a light string $1.0\ \text{m}$ long. (a) Find the least speed at the bottom for which it completes the circle, and the tensions at the bottom, at the horizontal and at the top for that speed. (b) The ball is instead given $6.0\ \text{m/s}$ at the bottom. Find the tension at the bottom, where the string goes slack, and the speed of the ball at that moment.
Find where the string goes slack in (b), as an angle above the horizontal, first:
(a) Speed $u_{\min}=\sqrt{5gr}=\sqrt{49}=7.0\ \text{m/s}$; then $v_\text{top}=\sqrt{gr}=3.13\ \text{m/s}$.
(a) Tensions $mg=1.96\ \text{N}$: bottom $6mg=11.8\ \text{N}$, horizontal $3mg=5.88\ \text{N}$, top $0$.
(b) Bottom $T=m\left(\dfrac{u^2}{r}+g\right)=0.20(36+9.8)=9.16\ \text{N}$. Since $\sqrt{2gr}=4.43\lt6.0\lt7.0$, the string will go slack somewhere above the horizontal.
(b) Slack $T=0$ when $\cos\theta=\dfrac{2gr-u^2}{3gr}=\dfrac{19.6-36}{29.4}=-0.558$: $\theta=123.9^\circ$ from the bottom, i.e. $33.9^\circ$ above the horizontal.
Speed there With $T=0$: $v^2=-gr\cos\theta=9.8\times0.558=5.47$, $v=2.34\ \text{m/s}$. Check with energy: $36-19.6(1+0.558)=5.47$ ✓.
⏱ Shortcut Remember the ladder $\sqrt{2gr}$ (reaches the horizontal), $\sqrt{4gr}$ (rod reaches the top), $\sqrt{5gr}$ (string completes the circle).

In the widget keep the string ($r=1.0\ \text{m}$, ball $0.20\ \text{kg}$) and set the speed at the bottom to $u=6.0\ \text{m/s}$. What happens?

Set the string and $u=6.0\ \text{m/s}$: the readouts show tension at the bottom $9.16\ \text{N}$, top "not reached", and the string slack at $33.9^\circ$ above the horizontal with the ball moving at $2.34\ \text{m/s}$. On the graph the tension curve crosses zero at $\theta=123.9^\circ$. The ball has more than enough energy to reach the horizontal ($u\gt\sqrt{2gr}=4.43\ \text{m/s}$) but less than the $\sqrt{5gr}=7.0\ \text{m/s}$ needed to stay on the circle at the top. Switch to the rod: it now goes right round, because the rod can push, and only $u\ge\sqrt{4gr}=6.26\ \text{m/s}$ is needed — so try $6.3\ \text{m/s}$.
Interactive 2 — Motion in a Vertical Circle

A $0.20\ \text{kg}$ ball moves in a vertical circle of radius $1.0\ \text{m}$, held by a string or by a light rod, starting from the bottom with speed $u$. Press Play. The graph shows the tension (or the rod's push, below zero) against the angle from the bottom. A string goes slack where its tension would turn negative, and the ball flies off as a projectile (dotted path). Try $u$ below $4.43$, between $4.43$ and $7.0$, and above $7.0\ \text{m/s}$.

6.0 m/s
tension at bottom—
speed at top—
force at top—
outcome—

A small ball is fixed to one end of a light rigid rod of length $r$ and whirled in a vertical circle about the other end. The least speed at the lowest point for it to go round completely is

Power

Two cranes lift identical loads to the same height; one takes ten seconds, the other a minute. They do the same work, but the first is six times more powerful. Power measures how fast work is done (or energy transferred).

📘 Definition 4.7 — Power

The average power of a force over a time interval $\Delta t$ in which it does work $\Delta W$ is $P_\text{av}=\dfrac{\Delta W}{\Delta t}$. The instantaneous power is $P=\dfrac{dW}{dt}$.

The SI unit is the watt, $1\ \text{W}=1\ \text{J/s}$ (dimensions $[\text{ML}^2\text{T}^{-3}]$); $1\ \text{horsepower}=746\ \text{W}$. The kilowatt hour is a unit of energy, not power: $1\ \text{kWh}=1000\ \text{W}\times3600\ \text{s}=3.6\times10^6\ \text{J}$.

📐 Result 4.10 — Power delivered by a force

A force $\mathbf{F}$ acting on a body moving with velocity $\mathbf{v}$ delivers power

$$P=\frac{\mathbf{F}\cdot d\mathbf{r}}{dt}=\mathbf{F}\cdot\mathbf{v}=Fv\cos\theta .$$

The work done in a time interval is $W=\displaystyle\int P\,dt$ (the area under the $P$–$t$ graph).

Vehicles. An engine working at power $P$ and moving at speed $v$ supplies a driving force $F=P/v$: large at low speed, small at high speed. The car reaches its maximum speed when the driving force has fallen to the total resistance $f$: $v_{\max}=P/f$ on the level, and $v_{\max}=\dfrac{P}{f+mg\sin\alpha}$ up a slope of angle $\alpha$. At any lower speed the net force $\dfrac{P}{v}-f$ accelerates the car.

Constant power from rest. If a body starts from rest and all of a constant power $P$ goes into kinetic energy, $\tfrac12mv^2=Pt$, so $v=\sqrt{2Pt/m}\propto t^{1/2}$; then $x=\int v\,dt\propto t^{3/2}$, and the acceleration falls as $t^{-1/2}$.

Pumps and efficiency. A pump lifting water at a rate $\dfrac{dm}{dt}$ through a height $h$ delivers useful power $\dfrac{dm}{dt}gh$ (plus $\tfrac12\dfrac{dm}{dt}v^2$ if the water leaves with speed $v$). The efficiency $\eta=\dfrac{P_\text{useful}}{P_\text{input}}$ is always less than $1$.

✏️ Example 6 — A car's top speed
A $1000\ \text{kg}$ car has an engine of maximum power $60\ \text{kW}$. The total resistance to its motion (air drag and rolling friction) is a constant $1500\ \text{N}$. Take $g=10\ \text{m/s}^2$. Find (a) its maximum speed on a level road, (b) its maximum speed up a slope with $\sin\alpha=\tfrac1{20}$, (c) its greatest possible acceleration on the level at the instant its speed is $20\ \text{m/s}$.
(a) At top speed the driving force equals the resistance: $v_{\max}=\dfrac{P}{f}=\dfrac{60\,000}{1500}=40\ \text{m/s}$ ($144\ \text{km/h}$).
(b) Extra resistance $mg\sin\alpha=1000\times10\times0.05=500\ \text{N}$: $v_{\max}=\dfrac{60\,000}{2000}=30\ \text{m/s}$.
(c) At $20\ \text{m/s}$ the full-power driving force is $\dfrac{60\,000}{20}=3000\ \text{N}$; net force $3000-1500=1500\ \text{N}$, so $a=1.5\ \text{m/s}^2$.
Check At $40\ \text{m/s}$ the same calculation gives $1500-1500=0$: no acceleration at top speed ✓.
⚠️ JEE Main traps

1. Using $K_i+U_i=K_f+U_f$ with friction present. If friction (or any applied force) does work, add $W_\text{nc}$: $K_i+U_i+W_\text{nc}=K_f+U_f$. And friction keeps acting while a spring is being compressed (Example 4).

2. Measuring the spring's $x$ from the wrong place. In $U=\tfrac12kx^2$, $x$ is the stretch or compression from the natural length — not the position of the block and not the change since some other point. For a block dropped onto a spring, the block falls $h+x$, not $h$.

3. The vertical-circle "ladder". String or inside of a loop: $u\ge\sqrt{5gr}$ and $v_\text{top}\ge\sqrt{gr}$. Rod or tube: $u\ge\sqrt{4gr}$. Reaching only the horizontal: $\sqrt{2gr}$. And $T_\text{bottom}-T_\text{top}=6mg$ only when the body actually goes round.

4. Sign of $F=-dU/dx$. The force points towards lower potential energy. Stable equilibrium is a minimum of $U$ (positive second derivative), not a maximum.

5. Power versus energy units. The kWh is energy ($3.6\times10^6\ \text{J}$), the watt is power. At top speed the driving force equals the resistance — the engine's power is not zero. And $P=Fv$ uses the speed at that instant, not an average.

A body starts from rest and is driven by a source of constant power, all of which goes into its kinetic energy. Its speed $v$ after time $t$ is proportional to

Exercises

Take $g=9.8\ \text{m/s}^2$ unless told otherwise. Springs and strings are light; surfaces are smooth unless friction is given.

I
Conservative forces and potential energy.
  • 1 Find the gain in gravitational potential energy of a $50\ \text{kg}$ girl who climbs $12\ \text{m}$ up a staircase.
  • 2 A particle has $U(x)=3x^2-2x$ (in J, $x$ in m). Find the force on it at $x=2\ \text{m}$.
  • 3 For $U(x)=2x^3-6x$ (in J, $x$ in m), find the equilibrium positions and state whether each is stable or unstable.
  • 4 A particle has $U(x)=\dfrac{10}{x}$ (in J, $x$ in m, $x\gt0$). Find the size and direction of the force at $x=2\ \text{m}$.
  • 5 Classify as conservative or non-conservative: gravity, the force of a spring, kinetic friction, air resistance. Give a one-line reason for friction.
  • 6 A $3.0\ \text{kg}$ stone is carried $200\ \text{m}$ along a winding path up to a point $25\ \text{m}$ higher, and then down to a point $10\ \text{m}$ above its start. Find the total work done on it by gravity.
  • 7 A $1.0\ \text{kg}$ block is dragged once round a square of side $2.0\ \text{m}$ on a floor with $\mu_k=0.40$, back to its starting point. Find the work done by friction. What does this show?
  • 8 A $2.5\ \text{kg}$ particle moves with $U(x)=5x^2$ (in J, $x$ in m) and total mechanical energy $20\ \text{J}$. Find its turning points and its greatest speed.
1 $\Delta U=mgh=50\times9.8\times12=5.9\times10^3\ \text{J}$ ($5880\ \text{J}$).
2 $F=-(6x-2)=-10\ \text{N}$ (towards $-x$).
3 $U'=6x^2-6=0$ at $x=\pm1\ \text{m}$; $U''=12x$: $x=+1$ stable (minimum), $x=-1$ unstable (maximum).
4 $F=-\dfrac{d}{dx}\left(\dfrac{10}{x}\right)=\dfrac{10}{x^2}=2.5\ \text{N}$, along $+x$ (repulsive, away from the origin).
5 Gravity and the spring force are conservative; friction and air resistance are not — friction always opposes the motion, so its work round a closed path is negative, never zero.
6 Only the net rise of $10\ \text{m}$ matters: $W=-3.0\times9.8\times10=-294\ \text{J}$.
7 $W_f=-\mu_kmg\times8.0=-0.40\times9.8\times8.0=-31.4\ \text{J}$; non-zero round a closed path, so friction is non-conservative.
8 Turning points where $U=E$: $5x^2=20$, $x=\pm2.0\ \text{m}$. Greatest speed at $x=0$: $\tfrac12(2.5)v^2=20$, $v=4.0\ \text{m/s}$.
II
Springs and conservation of mechanical energy.
  • 1 Find the energy stored in a spring of $k=250\ \text{N/m}$ compressed by $8.0\ \text{cm}$.
  • 2 A spring stores $0.50\ \text{J}$ when stretched by $2.0\ \text{cm}$. How much extra work is needed to stretch it from $2.0\ \text{cm}$ to $6.0\ \text{cm}$?
  • 3 A ball is dropped from a height of $5.0\ \text{m}$. Find its speed just before it hits the ground.
  • 4 A stone is thrown from the top of a $20\ \text{m}$ tower at $15\ \text{m/s}$. Find its speed on reaching the ground. Does the direction of the throw matter?
  • 5 A $0.40\ \text{kg}$ block moving at $2.0\ \text{m/s}$ on a smooth floor hits a spring with $k=100\ \text{N/m}$. Find the maximum compression.
  • 6 A $1.5\ \text{kg}$ block is dropped from $0.60\ \text{m}$ above the top of a vertical spring ($k=3000\ \text{N/m}$). Find the maximum compression.
  • 7 A $2.0\ \text{kg}$ block slides from rest down a rough curved track from a height of $3.0\ \text{m}$ and reaches the bottom at $6.0\ \text{m/s}$. Find the work done by friction.
  • 8 A $0.50\ \text{kg}$ block is pushed against a spring ($k=200\ \text{N/m}$), compressing it by $10\ \text{cm}$, and released on a floor with $\mu_k=0.20$. The block is not attached to the spring. Find its speed as it leaves the spring and the total distance it moves from the release point.
  • 9 A roller-coaster car starts from rest at a height of $30\ \text{m}$ on a frictionless track. Find its speed at a point $12\ \text{m}$ above the ground.
1 $U=\tfrac12(250)(0.080)^2=0.80\ \text{J}$.
2 $U\propto x^2$: at $6.0\ \text{cm}$, $U=9\times0.50=4.5\ \text{J}$; extra work $4.5-0.50=4.0\ \text{J}$.
3 $v=\sqrt{2gh}=\sqrt{98}=9.9\ \text{m/s}$.
4 $v=\sqrt{u^2+2gH}=\sqrt{225+392}=24.8\ \text{m/s}$, whatever the direction (only $K$ and $U$ enter).
5 $x=u\sqrt{m/k}=2.0\sqrt{0.0040}=0.126\ \text{m}=12.6\ \text{cm}$.
6 $mg(h+x)=\tfrac12kx^2$: $1500x^2-14.7x-8.82=0$, $x=\dfrac{14.7+\sqrt{216.1+52\,920}}{3000}=0.082\ \text{m}$ ($8.2\ \text{cm}$).
7 $W_f=\tfrac12mv^2-mgh=36-58.8=-22.8\ \text{J}$.
8 $\tfrac12kx^2=1.0\ \text{J}$; friction over $0.10\ \text{m}$ takes $0.20\times0.50\times9.8\times0.10=0.098\ \text{J}$: $\tfrac12(0.50)v^2=0.902$, $v=1.90\ \text{m/s}$. Total distance: $1.0=0.98\,d$, $d=1.02\ \text{m}$.
9 $v=\sqrt{2g(30-12)}=\sqrt{352.8}=18.8\ \text{m/s}$.
III
Motion in a vertical circle.
  • 1 Find the least speed at the lowest point for a stone on a $0.80\ \text{m}$ string to complete a vertical circle.
  • 2 Repeat part 1 for a ball on a light rod of the same length.
  • 3 A $0.50\ \text{kg}$ bob goes round a vertical circle on a string. Find the difference between the tensions at the lowest and highest points.
  • 4 A bob on a $1.0\ \text{m}$ string is given $5.0\ \text{m/s}$ at the bottom. Show that it does not complete the circle, and find the angle above the horizontal at which the string goes slack.
  • 5 A car on a smooth roller-coaster track is released from rest and must loop a circular loop of radius $10\ \text{m}$. Find the least release height above the bottom of the loop.
  • 6 A $0.10\ \text{kg}$ bob on a $0.50\ \text{m}$ string moving in a vertical circle has a tension of $9.0\ \text{N}$ at the lowest point. Find its speed at the highest point.
  • 7 A $0.30\ \text{kg}$ pendulum bob on a $2.0\ \text{m}$ string is released from rest with the string at $60^\circ$ to the vertical. Find the tension at the lowest point.
  • 8 A small block starts from rest at the top of a smooth fixed hemisphere of radius $1.2\ \text{m}$ and slides down its outside. At what height above the centre does it leave the surface?
1 $u=\sqrt{5gr}=\sqrt{39.2}=6.26\ \text{m/s}$.
2 $u=\sqrt{4gr}=\sqrt{31.36}=5.60\ \text{m/s}$.
3 $6mg=6\times0.50\times9.8=29.4\ \text{N}$, whatever the speed (as long as it goes round).
4 $\sqrt{2gr}=4.43\lt5.0\lt\sqrt{5gr}=7.0$: slack above the horizontal. $\cos\theta=\dfrac{19.6-25}{29.4}=-0.184$, so $\theta=100.6^\circ$ from the bottom — $10.6^\circ$ above the horizontal.
5 $H=\tfrac52r=25\ \text{m}$ (then $v_\text{top}=\sqrt{gr}$).
6 $9.0=0.10\left(\dfrac{u^2}{0.50}+9.8\right)$ gives $u^2=40.1$; $v_\text{top}^2=40.1-4(9.8)(0.50)=20.5$, $v_\text{top}=4.53\ \text{m/s}$.
7 $v^2=2gL(1-\cos60^\circ)=gL$; $T=mg+\dfrac{mv^2}{L}=2mg=5.88\ \text{N}$.
8 At angle $\theta$ from the top: $mg\cos\theta-N=\dfrac{mv^2}{R}$, $v^2=2gR(1-\cos\theta)$. With $N=0$: $\cos\theta=\tfrac23$, height above the centre $R\cos\theta=\tfrac23\times1.2=0.80\ \text{m}$.
IV
Power.
  • 1 A crane lifts a $500\ \text{kg}$ load through $12\ \text{m}$ at constant speed in $15\ \text{s}$. Find its power output.
  • 2 A pump raises $600\ \text{kg}$ of water per minute through a height of $25\ \text{m}$. Find the useful power, and the input power if the pump is $70\%$ efficient.
  • 3 A force $\mathbf{F}=(4\hat{\mathbf{i}}+3\hat{\mathbf{j}})\ \text{N}$ acts on a body moving with velocity $\mathbf{v}=(2\hat{\mathbf{i}}-\hat{\mathbf{j}})\ \text{m/s}$. Find the instantaneous power.
  • 4 A car's engine delivers $50\ \text{kW}$ at its maximum speed of $25\ \text{m/s}$ on a level road. Find the total resistive force.
  • 5 The car in part 4 has a mass of $1200\ \text{kg}$ and meets the same resistance. Find its maximum speed up a slope with $\sin\alpha=\tfrac1{20}$.
  • 6 A $2.0\ \text{kW}$ heater runs for $3.0$ hours. Find the energy used in kWh and in joules.
  • 7 A $2.0\ \text{kg}$ body starts from rest and receives a constant power of $16\ \text{W}$, all of which becomes kinetic energy. Find its speed after $4.0\ \text{s}$.
  • 8 The power delivered by a machine varies as $P=3t^2\ \text{W}$ ($t$ in s). Find the work done in the first $2.0\ \text{s}$.
1 $P=\dfrac{mgh}{t}=\dfrac{500\times9.8\times12}{15}=3.9\times10^3\ \text{W}$ ($3920\ \text{W}$).
2 Useful $\dfrac{600\times9.8\times25}{60}=2450\ \text{W}$; input $\dfrac{2450}{0.70}=3500\ \text{W}$.
3 $P=\mathbf{F}\cdot\mathbf{v}=8-3=5\ \text{W}$.
4 $f=\dfrac{P}{v_{\max}}=\dfrac{50\,000}{25}=2000\ \text{N}$.
5 $mg\sin\alpha=1200\times9.8/20=588\ \text{N}$; $v_{\max}=\dfrac{50\,000}{2588}=19.3\ \text{m/s}$.
6 $2.0\times3.0=6.0\ \text{kWh}=6.0\times3.6\times10^6=2.16\times10^7\ \text{J}$.
7 $\tfrac12mv^2=Pt=64\ \text{J}$, $v=\sqrt{64}=8.0\ \text{m/s}$.
8 $W=\displaystyle\int_0^2 3t^2\,dt=8.0\ \text{J}$.
🎯 Exam corner JEE Main · MCQJEE Main · Numerical

E1. JEE Main · MCQ The potential energy of a particle at distance $x$ from a fixed point is $U(x)=\dfrac{a}{x^{12}}-\dfrac{b}{x^{6}}$, where $a$ and $b$ are positive constants. The particle is in equilibrium at $x=$ (A) $\left(\dfrac{2a}{b}\right)^{1/6}$ (B) $\left(\dfrac{a}{b}\right)^{1/6}$ (C) $\left(\dfrac{b}{2a}\right)^{1/6}$ (D) $\left(\dfrac{2b}{a}\right)^{1/6}$

Condition Equilibrium: $F=-\dfrac{dU}{dx}=0$. $\dfrac{dU}{dx}=-\dfrac{12a}{x^{13}}+\dfrac{6b}{x^{7}}$.
Solve $\dfrac{6b}{x^7}=\dfrac{12a}{x^{13}}$ gives $x^6=\dfrac{2a}{b}$.
Answer (A).
⏱ Shortcut The powers $12$ and $6$ bring down a factor $12/6=2$ onto $a$. Option (B) forgets the factor from differentiating.

E2. JEE Main · Numerical A $0.5\ \text{kg}$ stone tied to a $1\ \text{m}$ string moves round a vertical circle. The tension in the string at the highest point is $15\ \text{N}$. Taking $g=10\ \text{m/s}^2$, find the tension (in N) at the lowest point. Give the answer to the nearest integer.

Top $T_\text{top}+mg=\dfrac{mv_\text{top}^2}{r}$: $15+5=0.5v_\text{top}^2$, so $v_\text{top}^2=40$.
Bottom $u^2=v_\text{top}^2+4gr=80$; $T_\text{bottom}=m\left(\dfrac{u^2}{r}+g\right)=0.5(80+10)=45\ \text{N}$.
Answer $45$.
⏱ Shortcut $T_\text{bottom}-T_\text{top}=6mg=30\ \text{N}$, so $15+30=45$.

E3. JEE Main · MCQ A body starts from rest and is acted on by a source of constant power, all of which is converted into its kinetic energy. The distance it covers in time $t$ is proportional to (A) $t$ (B) $t^2$ (C) $t^{3/2}$ (D) $t^{1/2}$

Speed $\tfrac12mv^2=Pt$ gives $v=\sqrt{\dfrac{2P}{m}}\,t^{1/2}$.
Distance $x=\displaystyle\int_0^t v\,dt=\sqrt{\dfrac{2P}{m}}\cdot\tfrac23t^{3/2}\propto t^{3/2}$.
Answer (C).
⏱ Shortcut Dimensions: $P$ fixed means $[ML^2T^{-3}]$ constant with $m$, so $x^2\propto t^3$. Option (D) is the speed, not the distance.

E4. JEE Main · Numerical A motor pumps $300\ \text{kg}$ of water per minute from a well up to a tank $18\ \text{m}$ above the water level. The motor has an efficiency of $60\%$. Taking $g=10\ \text{m/s}^2$ and neglecting the kinetic energy of the water, find the electrical power (in W) taken by the motor. Give the answer to the nearest integer.

Useful power $\dfrac{mgh}{t}=\dfrac{300\times10\times18}{60}=900\ \text{W}$.
Input $P_\text{in}=\dfrac{900}{0.60}=1500\ \text{W}$.
Answer $1500$.
⏱ Shortcut Convert "per minute" to per second first ($5\ \text{kg/s}$), then $5\times10\times18=900$. Multiplying by $0.6$ instead of dividing gives the wrong $540$.

E5. JEE Main · MCQ A small body on a string just manages to complete a vertical circle. The ratio of its kinetic energy at the lowest point to that at the highest point is (A) $2:1$ (B) $3:1$ (C) $4:1$ (D) $5:1$

Speeds Just completing: $v_\text{top}^2=gr$ and $u^2=v_\text{top}^2+4gr=5gr$.
Ratio $\dfrac{K_\text{bottom}}{K_\text{top}}=\dfrac{u^2}{v_\text{top}^2}=\dfrac{5gr}{gr}=5$.
Answer (D).
⏱ Shortcut $K_\text{top}=\tfrac12mgr$ and the fall of $2r$ adds $2mgr=4K_\text{top}$: total $5K_\text{top}$. Option (C) counts only the energy gained in the fall of $2r$ and forgets the energy the body already has at the top.

E6. JEE Main · Numerical A $2\ \text{kg}$ block is pushed against a light horizontal spring of spring constant $800\ \text{N/m}$, compressing it by $25\ \text{cm}$, and released from rest. It is not attached to the spring. The floor is rough with $\mu_k=0.25$; take $g=10\ \text{m/s}^2$. Find the distance (in cm) the block slides after leaving the spring before it stops. Give the answer to the nearest integer.

Energy Stored energy $\tfrac12(800)(0.25)^2=25\ \text{J}$; friction $\mu_kmg=5\ \text{N}$ acts over the whole path, including the $25\ \text{cm}$ inside the spring.
Distance Total sliding distance from release: $5d=25$, $d=5.00\ \text{m}$. After leaving the spring: $5.00-0.25=4.75\ \text{m}=475\ \text{cm}$.
Answer $475$.
⏱ Shortcut $d_\text{total}=\dfrac{kx^2}{2\mu_kmg}$, then subtract the compression. The tempting $500$ forgets that part of the slide happens while still touching the spring.
🔬 Research–Teaching NexusResearch-tutored · optional, about 45 minutes

Research question. How much of a bouncing ball's mechanical energy survives each bounce, and does the fraction lost stay the same from bounce to bounce?

Why it matters. Sports bodies specify how "lively" a ball must be: a tennis ball, a cricket ball and a football must each rebound to a set height when dropped onto a standard surface. Engineers designing running tracks, playground surfaces and shock absorbers want the opposite — surfaces that absorb energy to protect joints and heads. In both cases the measurement is simple energy bookkeeping: between bounces mechanical energy is conserved, and the drop in $mgh$ at each bounce is the work of non-conservative forces inside the ball and the floor.

What to do.

  1. Fix a metre scale (or tape) vertically against a wall. Drop a ball from a measured height $h_0$ and film it with a phone in slow motion.
  2. From the video, read the peak height $h_1,h_2,h_3,\dots$ after each of the first five bounces. Repeat three times and average.
  3. Compute the fraction of energy kept, $h_{n+1}/h_n$, for each bounce. Is it roughly constant? Plot $\ln h_n$ against $n$ — a straight line means a constant fraction.
  4. Repeat on two other surfaces (tiles, carpet, grass) and with a second kind of ball.
  5. For one ball, estimate the energy (in J) turned into heat and sound in the first bounce: $mg(h_0-h_1)$.

Tools: Two or three balls, kitchen scale, metre scale or tape, phone with slow-motion video, spreadsheet.

Hand in: A table of bounce heights; the graph of $\ln h_n$ against $n$ with its slope; the energy fraction per bounce for each ball–surface pair; a paragraph explaining where the "lost" energy went.

Going further. Warm a squash ball in your hands (or in warm water) for a few minutes and repeat. Why do squash players "warm up" the ball before a match?

Instructor note: a tennis ball on a hard floor typically keeps about 50–60% of its energy per bounce, a basketball 60–75%, a squash ball (cold) under 30%; carpet and grass lower the fractions sharply. The ratio is roughly constant over the first few bounces, so $\ln h_n$ is close to linear; small departures at low heights come from air resistance and reading errors. The warm squash ball bounces noticeably higher — a good discussion of how a material's energy loss depends on temperature.

🧪 Self-check quiz

0/5 correct

Q1. Which of these forces is non-conservative?

Q2. The mechanical energy $K+U$ of a body is conserved when

Q3. One kilowatt hour equals

Q4. A stone of mass $m$ on a string goes right round a vertical circle. The tension at the lowest point exceeds that at the highest point by

Q5. A spring stretched by $x$ stores energy $U$. The additional work needed to stretch it from $x$ to $2x$ is