Chapter 1 · Units and Measurements

1.1 Physical Quantities, SI Units and Significant Figures

A measurement is a number, a unit and an honest statement of how well we know it. The SI builds every unit from seven base units; the least count of an instrument decides how many significant figures a reading may carry.

In September 1999 NASA's Mars Climate Orbiter fired its engines to slip into orbit around Mars — and was never heard from again. The investigation found that software written by one team reported the push of the small steering thrusters in pound-force seconds, while the navigation software of another team read the same numbers as newton seconds. Since $1$ pound-force second is about $4.45$ newton seconds, every correction was misjudged by a factor of more than four, and the spacecraft dipped far too deep into the Martian atmosphere. The arithmetic was right; the units were not.

Every measurement in physics has three parts: a number, a unit, and a statement of how much of that number we can trust. This section builds all three from scratch: physical quantities and systems of units, the seven base units of the SI and the units derived from them, prefixes and practical units for very large and very small things, the least count of an instrument, and the rules of significant figures that stop a calculator from inventing precision. JEE Main asks one or two questions on this unit in almost every paper, and the ideas are used in every other chapter. Section 1.2 adds dimensions; Section 1.3 treats errors in measurement in full.

Physical quantities and systems of units

Length, mass, time, temperature, force, energy, electric current: each can be measured, and each measurement is a comparison with a standard of the same kind. "The rod is $2.5\ \text{m}$ long" means the rod is two and a half times as long as the standard called the metre.

📘 Definition 1.1 — Physical quantity, unit and numerical value

A physical quantity is a property of a body, a substance or a process that can be measured. A unit is an agreed reference standard of the same kind. The measured value of a quantity $Q$ is written

$$Q = n\,u,$$

where $u$ is the unit and $n$ is the numerical value (or magnitude) of $Q$ in that unit. The quantity itself does not depend on the unit we choose, so if the same $Q$ is measured in two units,

$$n_1u_1=n_2u_2\qquad\Longrightarrow\qquad n\propto\frac1u .$$

A larger unit gives a smaller number: $2.5\ \text{m} = 250\ \text{cm}$, because the centimetre is a hundred times smaller than the metre. A good unit should be well defined, easy to reproduce anywhere, unaffected by time, temperature or place, and of a convenient size.

We do not need an independent standard for every quantity. Once length and time have units, speed (length ÷ time) and acceleration (speed ÷ time) have units automatically; add a unit of mass and force (mass × acceleration) follows.

📘 Definition 1.2 — Fundamental and derived quantities

The fundamental (or base) quantities of a system of units are a small set of quantities chosen to be independent of one another — none can be expressed in terms of the others. Their units are the fundamental (base) units.

Every other quantity is a derived quantity: it is defined by an equation involving base quantities, and its derived unit is the corresponding product of powers of base units. For example, density $\rho=m/V$ has the derived unit $\text{kg}/\text{m}^3=\text{kg m}^{-3}$.

A system of units is a complete set of base units together with the rules for forming derived units. Four systems have been used in mechanics:

SystemLengthMassTimeUnit of force
CGS (Gaussian)centimetregramseconddyne $=1\ \text{g cm s}^{-2}=10^{-5}\ \text{N}$
FPS (British)footpoundsecondpoundal
MKSmetrekilogramsecondnewton
SI (from 1960)metrekilogramsecondnewton — plus four more base quantities

The Système International d'Unités (SI), agreed internationally in 1960, extends the MKS system to the whole of physics and chemistry with seven base quantities. Since 2019 every one of its base units is defined by fixing the exact numerical value of a constant of nature, so that any well-equipped laboratory can realise it without a physical prototype.

Base quantitySI unitSymbolDefined by fixing
lengthmetremspeed of light, $c=299\,792\,458\ \text{m/s}$
masskilogramkgPlanck constant, $h=6.626\,070\,15\times10^{-34}\ \text{J s}$
timesecondscaesium-133 transition frequency, $9\,192\,631\,770\ \text{Hz}$
electric currentampereAelementary charge, $e=1.602\,176\,634\times10^{-19}\ \text{C}$
thermodynamic temperaturekelvinKBoltzmann constant, $k_B=1.380\,649\times10^{-23}\ \text{J/K}$
amount of substancemolemolAvogadro constant, $N_A=6.022\,140\,76\times10^{23}\ \text{mol}^{-1}$
luminous intensitycandelacdluminous efficacy of $540\times10^{12}\ \text{Hz}$ light, $683\ \text{lm/W}$

In words: the second is the duration of $9\,192\,631\,770$ periods of the radiation from a particular transition of the caesium-133 atom (the heartbeat of an atomic clock); the metre is the distance light travels in vacuum in $1/299\,792\,458$ of a second; the kilogram is fixed through $h$ and realised with a Kibble balance, which weighs a mass against an electromagnetic force. The other units — litre, hour, degree Celsius, electronvolt — are used with the SI but are not part of it.

Two units of angle complete the list. They used to be called supplementary units; today they are classed as dimensionless derived units, because each is a ratio of two lengths or of an area to a length squared.

📘 Definition 1.3 — Radian and steradian

An arc of length $\Delta s$ on a circle of radius $r$ subtends at the centre the plane angle $\Delta\theta=\dfrac{\Delta s}{r}$, measured in radians (rad). A full circle is $2\pi\ \text{rad}=360^\circ$.

A patch of area $\Delta A$ on a sphere of radius $r$ subtends at the centre the solid angle $\Delta\Omega=\dfrac{\Delta A}{r^2}$, measured in steradians (sr). A full sphere is $4\pi\ \text{sr}$.

Both formulas assume the arc or patch is measured along the circle or sphere; for a small, nearly flat object far away they hold to a very good approximation with $\Delta s$ its width and $\Delta A$ its area seen face-on.

Useful conversions: $1^\circ=\dfrac{\pi}{180}\ \text{rad}=1.745\times10^{-2}\ \text{rad}$; one minute of arc $1'=\tfrac{1}{60}^\circ=2.909\times10^{-4}\ \text{rad}$; one second of arc $1''=\tfrac{1}{60}'=4.848\times10^{-6}\ \text{rad}$.

🧭 Rules for writing SI units and symbols
  1. Unit symbols are lower case unless the unit is named after a person: m, kg, s, mol, cd — but N (Newton), Pa (Pascal), J (Joule), W (Watt), K (Kelvin), A (Ampère). The litre may be written L to avoid confusion with the digit 1.
  2. Written in full, unit names are lower case: newton, joule, kelvin (but "degree Celsius").
  3. Symbols take no plural and no full stop: $5\ \text{kg}$, not "5 kgs" or "5 kg." (except at the end of a sentence).
  4. Leave a space between the number and the symbol ($25\ \text{m}$), and between symbols in a product ($\text{N m}$, or $\text{N}\cdot\text{m}$). Use at most one solidus: $\text{m/s}^2$ or $\text{m s}^{-2}$, and $\text{J/(kg K)}$ or $\text{J kg}^{-1}\text{K}^{-1}$, never "J/kg/K".
  5. Temperatures in kelvin have no degree sign: $300\ \text{K}$, not "300 °K".
  6. A prefix is joined to the symbol and never doubled: $\text{ns}$, not "mμs". The prefix and symbol form one unit, so $1\ \text{cm}^3=(10^{-2}\ \text{m})^3=10^{-6}\ \text{m}^3$.
✏️ Example 1 — Derived units in base units
Express each SI unit in terms of base units: (a) the newton, from $F=ma$; (b) the pascal, from $p=F/A$; (c) the joule, from $W=Fs$; (d) the watt, from $P=W/t$; (e) the coulomb, from $q=It$. Then show that $1\ \text{N s}$ (the unit of impulse) is the same as the unit of momentum.
(a), (b) $1\ \text{N}=1\ \text{kg}\times1\ \text{m/s}^2=1\ \text{kg m s}^{-2}$. $1\ \text{Pa}=1\ \text{N/m}^2=1\ \text{kg m}^{-1}\text{s}^{-2}$.
(c), (d) $1\ \text{J}=1\ \text{N m}=1\ \text{kg m}^2\text{s}^{-2}$. $1\ \text{W}=1\ \text{J/s}=1\ \text{kg m}^2\text{s}^{-3}$.
(e) $1\ \text{C}=1\ \text{A s}$: the coulomb is derived, because current (not charge) is the SI base quantity.
Impulse $1\ \text{N s}=1\ \text{kg m s}^{-2}\times\text{s}=1\ \text{kg m s}^{-1}$, which is the unit of momentum $mv$ ✓ — as it must be, since impulse equals change of momentum.
Check Dividing (c) by (a): $\dfrac{\text{kg m}^2\text{s}^{-2}}{\text{kg m s}^{-2}}=\text{m}$, the unit of the distance in $W=Fs$ ✓.
✏️ Example 2 — Plane and solid angle of the Moon
The Moon has a diameter of $3.47\times10^6\ \text{m}$ and is $3.84\times10^8\ \text{m}$ from the Earth. (a) Find the angle it subtends at your eye, in radians, degrees and minutes of arc. (b) Find the solid angle it subtends. (c) How far from your eye must a coin of diameter $2.0\ \text{cm}$ be held to just cover the full Moon?
(a) The Moon is tiny compared with its distance, so its diameter is effectively an arc: $\theta=\dfrac{3.47\times10^6}{3.84\times10^8}=9.04\times10^{-3}\ \text{rad}$. In degrees: $9.04\times10^{-3}\times\dfrac{180}{\pi}=0.518^\circ$, about $31'$.
(b) The face-on disc has area $\pi R^2$ with $R=1.735\times10^6\ \text{m}$: $\Omega=\dfrac{\pi(1.735\times10^6)^2}{(3.84\times10^8)^2}=6.41\times10^{-5}\ \text{sr}$.
(c) The coin must subtend the same angle: $d=\dfrac{0.020\ \text{m}}{9.04\times10^{-3}}=2.2\ \text{m}$.
Check The Moon covers $\Omega/4\pi\approx5\times10^{-6}$ of the whole sky — about one part in two hundred thousand, which is why it looks so small even though it is $3470\ \text{km}$ across.

A length has the numerical value $5.0$ in some unit. It is re-measured in a new unit that is ten times larger. Its numerical value becomes

Prefixes, practical units and converting units

Physics ranges from the radius of a proton (about $10^{-15}\ \text{m}$) to the size of the observable universe (about $10^{26}\ \text{m}$). Scientific notation $a\times10^{b}$ with $1\le a\lt10$ handles this range, and SI prefixes give names to the powers of ten.

PowerPrefixSymbolPowerPrefixSymbol
$10^{18}$exaE$10^{-1}$decid
$10^{15}$petaP$10^{-2}$centic
$10^{12}$teraT$10^{-3}$millim
$10^{9}$gigaG$10^{-6}$microμ
$10^{6}$megaM$10^{-9}$nanon
$10^{3}$kilok$10^{-12}$picop
$10^{2}$hectoh$10^{-15}$femtof
$10^{1}$decada$10^{-18}$attoa

The kilogram is the only base unit that already contains a prefix, so prefixes for mass are attached to the gram: $1\ \text{mg}=10^{-6}\ \text{kg}$, never "1 μkg". Some non-SI units are so convenient in particular fields that they are still used every day — and JEE Main expects you to know them.

UnitValue in SIWhere it is used
fermi (femtometre), fm$1\ \text{fm}=10^{-15}\ \text{m}$sizes of nuclei
ångström, Å$1\ \text{Å}=10^{-10}\ \text{m}$atoms, X-ray wavelengths
micron, μm$10^{-6}\ \text{m}$cells, fibres, dust
astronomical unit, AU$1.496\times10^{11}\ \text{m}$mean Earth–Sun distance
light year, ly$9.46\times10^{15}\ \text{m}$distance light travels in one year
parsec, pc$3.09\times10^{16}\ \text{m}=3.26\ \text{ly}$distances to stars
atomic mass unit, u$1.66\times10^{-27}\ \text{kg}$$\tfrac{1}{12}$ of the mass of a carbon-12 atom
tonne (metric ton), quintal$10^3\ \text{kg}$, $10^2\ \text{kg}$trade, transport
electronvolt, eV$1.602\times10^{-19}\ \text{J}$atoms, nuclei, semiconductors
kilowatt hour, kWh$3.6\times10^{6}\ \text{J}$the "unit" on an electricity bill
calorie, cal$4.186\ \text{J}$heat, food energy
atmosphere, bar, torr$1.013\times10^5\ \text{Pa}$, $10^5\ \text{Pa}$, $133.3\ \text{Pa}$pressure (1 torr = 1 mm of mercury)
litre, L$10^{-3}\ \text{m}^3=1000\ \text{cm}^3$volume
horsepower, hp$746\ \text{W}$engines
📐 Principle 1.1 — Converting units with factors of one

Any true relation between units, such as $1\ \text{km}=1000\ \text{m}$, can be written as a ratio equal to one: $\dfrac{1000\ \text{m}}{1\ \text{km}}=1$. Multiplying a quantity by such a ratio changes its numerical value and its unit but not the quantity. Equivalently, $n_2=n_1\dfrac{u_1}{u_2}$.

For a derived unit, convert each base unit separately, raising each factor to the same power as its unit: $1\ \text{m}^3=(100\ \text{cm})^3=10^6\ \text{cm}^3$, and $1\ \text{m/s}=\dfrac{10^{-3}\ \text{km}}{\tfrac{1}{3600}\ \text{h}}=3.6\ \text{km/h}$.

✏️ Example 3 — Light year, astronomical unit and parsec
(a) Taking $c=2.998\times10^8\ \text{m/s}$ and $1\ \text{year}=3.156\times10^{7}\ \text{s}$, find the light year in metres. (b) The parsec is the distance at which a length of $1\ \text{AU}$, seen side-on, subtends an angle of $1''$. Find $1\ \text{pc}$ in metres, in light years and in AU. (c) The nearest star after the Sun, Proxima Centauri, is $4.24\ \text{ly}$ away. Find its distance in parsec and the angle that the radius of the Earth's orbit subtends at the star (its parallax).
Work out (c), the parallax of Proxima Centauri in seconds of arc, before you open the solution:
(a) $1\ \text{ly}=c\times(1\ \text{yr})=2.998\times10^8\times3.156\times10^7=9.46\times10^{15}\ \text{m}$.
(b) $1''=\dfrac{\pi}{180\times3600}\ \text{rad}=4.848\times10^{-6}\ \text{rad}$. With arc $=$ radius $\times$ angle: $1\ \text{pc}=\dfrac{1.496\times10^{11}\ \text{m}}{4.848\times10^{-6}}=3.086\times10^{16}\ \text{m}$. Dividing: $\dfrac{3.086\times10^{16}}{9.462\times10^{15}}=3.26\ \text{ly}$, and $\dfrac{1}{4.848\times10^{-6}}=2.06\times10^5\ \text{AU}$.
(c) $d=\dfrac{4.24}{3.26}=1.30\ \text{pc}$. By the definition, a star at $d$ parsec has parallax $p=\dfrac1d$ seconds of arc: $p=\dfrac{1}{1.30}=0.769''$.
Check Even the nearest star shows a parallax smaller than one second of arc — the width of a coin seen from about $4\ \text{km}$. That is why stellar parallax was first measured only in 1838.
✏️ Example 4 — Converting compound units
Convert (a) $72\ \text{km/h}$ to $\text{m/s}$; (b) the density of mercury, $13.6\ \text{g/cm}^3$, to $\text{kg/m}^3$; (c) $g=9.8\ \text{m/s}^2$ to $\text{km/h}^2$; (d) $1\ \text{kWh}$ to electronvolts.
(a) $72\ \dfrac{\text{km}}{\text{h}}\times\dfrac{1000\ \text{m}}{1\ \text{km}}\times\dfrac{1\ \text{h}}{3600\ \text{s}}=20\ \text{m/s}$ (shortcut: divide by $3.6$).
(b) $13.6\ \dfrac{\text{g}}{\text{cm}^3}\times\dfrac{10^{-3}\ \text{kg}}{1\ \text{g}}\times\left(\dfrac{100\ \text{cm}}{1\ \text{m}}\right)^3=13.6\times10^{-3}\times10^{6}=1.36\times10^4\ \text{kg/m}^3$.
(c) $9.8\ \dfrac{\text{m}}{\text{s}^2}\times\dfrac{1\ \text{km}}{1000\ \text{m}}\times\left(\dfrac{3600\ \text{s}}{1\ \text{h}}\right)^2=9.8\times10^{-3}\times1.296\times10^{7}=1.3\times10^{5}\ \text{km/h}^2$. The time factor is squared, because $\text{s}^2$ is.
(d) $1\ \text{kWh}=1000\ \text{W}\times3600\ \text{s}=3.6\times10^6\ \text{J}$; $\dfrac{3.6\times10^6}{1.602\times10^{-19}}=2.25\times10^{25}\ \text{eV}$.
Check Density of water: $1\ \text{g/cm}^3=1000\ \text{kg/m}^3$, so any density in $\text{g/cm}^3$ is multiplied by $1000$ — consistent with (b).

An area of $1\ \text{mm}^2$ expressed in square metres is

Least count and significant figures

Lay a metre rule along a pencil. Its end falls between the $14\ \text{cm}$ and $15\ \text{cm}$ marks, a little past the seventh millimetre mark. You can be sure of "$14.7\ \text{cm}$"; you cannot honestly claim "$14.732\ \text{cm}$", because the rule has no marks finer than a millimetre. Every instrument has a smallest step it can resolve, and this step decides how many digits of a reading mean anything.

📘 Definition 1.4 — Least count

The least count (LC) of a measuring instrument is the smallest change in the measured quantity that the instrument can resolve — normally the value of its smallest division, or of its finest reading. A reading is recorded to the decimal place of the least count.

Typical values: metre rule $1\ \text{mm}$; Vernier callipers $0.1\ \text{mm}$ or $0.05\ \text{mm}$ (or $0.02\ \text{mm}$); screw gauge $0.01\ \text{mm}$ (or $0.005\ \text{mm}$); spherometer $0.01\ \text{mm}$; mechanical stopwatch $0.1\ \text{s}$; digital stopwatch $0.01\ \text{s}$; laboratory thermometer $1\ ^\circ\text{C}$ (or $0.5\ ^\circ\text{C}$).

Two instruments beat the millimetre without a microscope. A Vernier calliper has a small sliding scale whose divisions are slightly shorter than the main-scale divisions; a screw gauge turns a fine screw whose rotation is read on a circular scale. Their construction and use (including zero errors) are part of the experimental skills of Chapter 20; here we need only their least counts and how a reading is formed.

📐 Rule 1.2 — Least count of a Vernier and of a screw gauge

Vernier. If $n$ Vernier scale divisions (VSD) have the same length as $(n-1)$ main scale divisions (MSD), then $1\ \text{VSD}=\tfrac{n-1}{n}\ \text{MSD}$ and

$$\text{LC}=1\ \text{MSD}-1\ \text{VSD}=\frac{1\ \text{MSD}}{n}.$$

Reading $=$ main scale reading (the mark just before the Vernier zero) $+$ (number of the Vernier division that coincides with a main-scale mark) $\times$ LC.

Screw gauge. If the spindle advances by the pitch $p$ in one full turn and the circular scale has $N$ divisions, then

$$\text{LC}=\frac{p}{N}.$$

Reading $=$ main (linear) scale reading $+$ (circular scale division on the reference line) $\times$ LC. (Both rules assume no zero error.)

The digits of a reading therefore come in two kinds: those the instrument shows for certain, and one last digit that sits at the level of the least count and could be one step either way. Together they are the significant figures.

📘 Definition 1.5 — Significant figures

The significant figures (s.f.) of a measured value are all the digits that are known reliably plus the first digit that is uncertain. A reading of $14.7\ \text{cm}$ from a metre rule has three significant figures: $1$ and $4$ are certain, and $7$ is the first uncertain digit. The more significant figures a value has, the more precise the measurement.

📐 Rule 1.3 — Counting significant figures
  1. Every non-zero digit is significant: $4.762$ has 4 s.f.
  2. Zeros between non-zero digits are significant: $2008$ and $3.054$ have 4 s.f.
  3. Zeros to the left of the first non-zero digit only locate the decimal point and are not significant: $0.00405$ has 3 s.f.
  4. Trailing zeros in a number with a decimal point are significant: $4.500$ and $450.0$ have 4 s.f.; $0.004050$ has 4 s.f.
  5. Trailing zeros in a whole number written without a decimal point are ambiguous: $4500$ may have 2, 3 or 4 s.f. Scientific notation removes the doubt: $4.5\times10^3$ (2), $4.50\times10^3$ (3), $4.500\times10^3$ (4).
  6. The power of ten is never significant, so changing units does not change the number of s.f.: $2.30\ \text{m}=2.30\times10^2\ \text{cm}=2.30\times10^{-3}\ \text{km}$ — three each.
  7. Exact numbers — counted objects, defined conversion factors, the $2$ and $\pi$ in $2\pi r$ — have unlimited significant figures and never limit a result.

Order of magnitude. To compare sizes quickly, write a number as $a\times10^{b}$ with $0.5\lt a\le5$; then $b$ is its order of magnitude. The radius of the Earth, $6.37\times10^6\ \text{m}=0.637\times10^7\ \text{m}$, has order of magnitude $7$; the mass of an electron, $9.11\times10^{-31}\ \text{kg}=0.911\times10^{-30}\ \text{kg}$, has order $-30$. Two quantities of the same order differ by a factor less than about ten.

Set the rod's true length to $18.46\ \text{mm}$. How many significant figures will the readings of the metre rule, the Vernier calliper and the screw gauge have (in that order)?

Drag the slider to $18.46\ \text{mm}$ and switch the instrument. The metre rule reads $18\ \text{mm}$ (2 s.f.), the Vernier $18.5\ \text{mm}$ (3 s.f.: main scale $18$, Vernier division $5$), and the screw gauge $18.46\ \text{mm}$ (4 s.f.: linear scale $18.0$, circular division $46$). Each tenfold smaller least count adds one trustworthy digit. The "in metres" readout, $1.846\times10^{-2}\ \text{m}$ for the screw gauge, keeps the same 4 s.f. — changing the unit never changes the number of significant figures.
Interactive 1 — Least Count Decides the Digits

The same rod is measured with three instruments. Choose the instrument and drag the slider to change the rod's true length (which no instrument knows exactly). The metre rule reads to the nearest millimetre; on the Vernier, find the division that lines up with a main-scale mark (red); on the screw gauge, read the linear scale and then the circular scale at the reference line. Press Play to let the length drift and watch which digits change.

14.37 mm
reading—
least count—
significant figures—
in metres—
✏️ Example 5 — Reading a Vernier and a screw gauge
(a) In a Vernier calliper $20$ Vernier divisions coincide with $19$ main-scale divisions of $1\ \text{mm}$ each. Find its least count. (b) Measuring a cylinder, the Vernier zero lies just past the $32\ \text{mm}$ mark and the $7$th Vernier division coincides with a main-scale mark. Find the length and its number of significant figures. (c) A screw gauge has pitch $0.5\ \text{mm}$ and $100$ circular divisions. With a wire in place the linear scale shows $4.5\ \text{mm}$ and the $37$th circular division is on the reference line. Find the diameter. (d) What would a metre rule give for the same wire, and how many significant figures?
Find the two readings (b) and (c) yourself first:
(a) $20\ \text{VSD}=19\ \text{MSD}$, so $n=20$: $\text{LC}=\dfrac{1\ \text{mm}}{20}=0.05\ \text{mm}$.
(b) Reading $=32\ \text{mm}+7\times0.05\ \text{mm}=32.35\ \text{mm}=3.235\ \text{cm}$: four significant figures (the last digit is at the level of the least count).
(c) $\text{LC}=\dfrac{0.5\ \text{mm}}{100}=0.005\ \text{mm}$; diameter $=4.5+37\times0.005=4.685\ \text{mm}$ (4 s.f.).
(d) A metre rule reads to the nearest millimetre: $5\ \text{mm}$ — a single significant figure. The screw gauge gives three more trustworthy digits for the same wire.
⏱ Shortcut For "$n$ VSD $=(n-1)$ MSD", $\text{LC}=\text{MSD}/n$ directly; for the screw gauge, $\text{LC}=$ pitch ÷ number of circular divisions.

A Vernier calliper has a least count of $0.02\ \text{mm}$. Which of these could be a correctly recorded reading from it?

Significant figures in calculations; rounding off

A calculator does not know how good your data are. Divide $10.0\ \text{m}$ by $3.0\ \text{s}$ and it shows $3.333333333$ — eight digits that the stopwatch never saw. The rules below keep the precision of a result in line with the precision of the data that produced it. Interactive 2 shows why they work: it tracks the whole range of values each measured number could really have.

📐 Rule 1.4 — Significant figures in arithmetic

Multiplication and division. The result keeps as many significant figures as the factor with the fewest significant figures: $\dfrac{4.237\ \text{g}}{2.51\ \text{cm}^3}=1.69\ \text{g/cm}^3$ (3 s.f., set by $2.51$).

Addition and subtraction. The result keeps as many decimal places as the term with the fewest decimal places: $436.32+227.2+0.301=663.821\to663.8$ (1 decimal place, set by $227.2$).

Exact numbers and defined constants never limit a result. In a calculation with several steps, keep one or two extra digits in the intermediate results and round only the final answer.

Subtraction can destroy significant figures: $5.36\ \text{cm}-5.31\ \text{cm}=0.05\ \text{cm}$ has only one significant figure, although each length had three. This is why physicists avoid finding a small quantity as the difference of two nearly equal large ones.

📐 Rule 1.5 — Rounding off

To round a number to a given number of significant figures (or decimal places), look at the part to be dropped:

  1. If it is less than half a unit of the last kept place (first dropped digit $0$–$4$), leave the last kept digit unchanged: $2.7432\to2.74$.
  2. If it is more than half (first dropped digit $6$–$9$, or $5$ followed by any non-zero digit), raise the last kept digit by one: $2.7462\to2.75$, $2.7451\to2.75$.
  3. If it is exactly half (a single $5$, or $5$ followed only by zeros), round so that the last kept digit is even: $2.745\to2.74$ and $2.735\to2.74$.

Round in one step from the full number, never digit by digit: $2.7449\to2.74$ (rounding first to $2.745$ and then to $2.75$ would be wrong).

The "round half to even" rule means that, over many measurements, exact halves are rounded up and down equally often, so rounding introduces no bias. It is the convention used in Indian school and JEE examinations.

✏️ Example 6 — Density of a metal cylinder
A metal cylinder has mass $141.4\ \text{g}$ (digital balance), diameter $2.04\ \text{cm}$ (Vernier) and length $5.125\ \text{cm}$. (a) Find its density with the correct number of significant figures, in $\text{g/cm}^3$ and in $\text{kg/m}^3$. (b) It is put into a beaker of mass $63.2\ \text{g}$ holding $50.15\ \text{g}$ of water. Report the total mass correctly.
Find the density in (a) before you open the solution:
Volume $V=\dfrac{\pi d^2}{4}L=\dfrac{\pi(2.04)^2}{4}\times5.125=16.75\ \text{cm}^3$ (keep extra digits; $\pi$ and $4$ are exact).
(a) $\rho=\dfrac{141.4}{16.751}=8.441\ \text{g/cm}^3$. The data have $4$, $3$ and $4$ s.f.; the diameter limits the answer to 3 s.f.: $\rho=8.44\ \text{g/cm}^3=8.44\times10^3\ \text{kg/m}^3$.
(b) $141.4+63.2+50.15=254.75\ \text{g}$. The fewest decimal places is one, so round to one decimal place. The dropped part is exactly $5$ and the digit before it, $7$, is odd: raise it. Total $=254.8\ \text{g}$.
Check Densities of common metals lie between about $2.7\ \text{g/cm}^3$ (aluminium) and $19.3\ \text{g/cm}^3$ (gold); $8.44$ is close to brass. The diameter is squared, so its single uncertain digit matters most — the diameter is the measurement to improve.

Choose A − B with $2$ decimals in A and $2$ decimals in B, so $A=37.49$ and $B=36.91$ — four significant figures each. How many significant figures does the answer by Rule 1.4 have?

With operation A − B and both sliders at $2$, the readouts show A $=37.49$, B $=36.91$, calculator $0.58$ and by Rule 1.4 $0.58$. The result keeps two decimal places, but $0.58$ has only 2 significant figures: the shaded range runs from $0.57000$ to $0.59000$, so the second digit is already uncertain. Subtracting two nearly equal numbers wipes out the leading digits they share — the absolute uncertainty stays the same while the result becomes small.
Interactive 2 — Why the Significant-Figure Rules Work

Two quantities are measured to the number of decimal places you choose; each recorded value could really be anywhere within half a unit of its last digit. The bars show how big these uncertainties are — relative uncertainties for × and ÷, absolute ones for + and −. The number line shows every value the result could really have (shaded), the calculator's answer (dot) and the answer given by Rule 1.4 (purple), with grid lines one unit of its last digit apart. Press Play to step through cases.

21
A—
B—
calculator—
by Rule 1.4—
⚠️ JEE Main traps

1. Trailing zeros. $2.50$ has three significant figures, $2.5$ has two, and $0.002500$ has four. Leading zeros never count; trailing zeros after a decimal point always do.

2. Changing units does not change significant figures. $3.20\ \text{m}$ is $3.20\times10^2\ \text{cm}$ (3 s.f.), not "320 cm" (ambiguous) and not $3.2\times10^{2}\ \text{cm}$ (2 s.f.).

3. Using the wrong arithmetic rule. Sums and differences are limited by decimal places; products and quotients by significant figures. In a mixed calculation apply the rules step by step, keeping a guard digit.

4. Rounding an exact half. $6.35\to6.4$ but $6.25\to6.2$ (to even); and $6.251\to6.3$, because the dropped part is more than half. Never round in two stages.

5. Least counts. "$\text{LC}=\text{MSD}/n$" holds only when $n$ VSD $=(n-1)$ MSD; in general $\text{LC}=1\ \text{MSD}-1\ \text{VSD}$. For a screw gauge, find the pitch first ("moves $2.5\ \text{mm}$ in $5$ turns" means $p=0.5\ \text{mm}$).

Two measured values are multiplied: $2.5\times3.42$. With the correct significant figures and the round-half-to-even rule, the result is

Exercises

Use the rules of this section for every answer: correct units, correct significant figures, and round half to even.

I
Quantities, systems of units and angles.
  • 1 Classify each as an SI base quantity or a derived quantity: luminous intensity, force, amount of substance, density, electric charge, thermodynamic temperature.
  • 2 Express in SI base units the coulomb (from $q=It$) and the volt (from $V=W/q$).
  • 3 Correct the way these are written: "5 Kgs", "20 mps", "300 °K", "10 n", "3 m.m.", "9.8 m/s/s".
  • 4 Express the unit of surface tension (force per unit length) in base units, and show that $1\ \text{Pa}=1\ \text{J/m}^3$.
  • 5 A tree $6.0\ \text{m}$ tall stands $150\ \text{m}$ away. Find the angle it subtends at your eye in radians and degrees.
  • 6 Find the solid angle subtended at the centre of a sphere of radius $5.0\ \text{m}$ by (a) a hemisphere of it, (b) a patch of area $1.0\ \text{m}^2$ on its surface.
  • 7 Express one minute of arc and one second of arc in radians.
  • 8 Which of these is not an SI base unit: kelvin, candela, gram, mole, ampere? Explain.
1 Base: luminous intensity, amount of substance, thermodynamic temperature. Derived: force ($ma$), density ($m/V$), electric charge ($It$).
2 $1\ \text{C}=1\ \text{A s}$; $1\ \text{V}=1\ \dfrac{\text{J}}{\text{C}}=\dfrac{\text{kg m}^2\text{s}^{-2}}{\text{A s}}=1\ \text{kg m}^2\text{s}^{-3}\text{A}^{-1}$.
3 $5\ \text{kg}$; $20\ \text{m/s}$; $300\ \text{K}$; $10\ \text{N}$; $3\ \text{mm}$; $9.8\ \text{m/s}^2$ (or $\text{m s}^{-2}$).
4 $\text{N/m}=\text{kg m s}^{-2}/\text{m}=\text{kg s}^{-2}$. $\text{J/m}^3=\text{N m/m}^3=\text{N/m}^2=\text{Pa}$ ✓ (pressure is also energy per unit volume).
5 $\theta=\dfrac{6.0}{150}=0.040\ \text{rad}=2.3^\circ$.
6 (a) $\dfrac{2\pi r^2}{r^2}=2\pi=6.28\ \text{sr}$ (independent of the radius); (b) $\dfrac{1.0}{5.0^2}=0.040\ \text{sr}$.
7 $1'=\dfrac{\pi}{180\times60}=2.9\times10^{-4}\ \text{rad}$; $1''=\dfrac{\pi}{180\times3600}=4.8\times10^{-6}\ \text{rad}$.
8 The gram. The SI base unit of mass is the kilogram; the gram is $10^{-3}\ \text{kg}$.
II
Prefixes, practical units and conversions.
  • 1 Convert $54\ \text{km/h}$ to $\text{m/s}$, and $25\ \text{m/s}$ to $\text{km/h}$.
  • 2 The density of aluminium is $2.70\ \text{g/cm}^3$. Express it in $\text{kg/m}^3$.
  • 3 How many litres, and how many cubic centimetres, are there in $1\ \text{m}^3$?
  • 4 A $1.5\ \text{kW}$ heater runs for $40\ \text{min}$. Find the energy used in kWh and in joules.
  • 5 The Earth–Sun distance is $1.496\times10^{11}\ \text{m}$. How long does sunlight take to reach us? ($c=3.00\times10^8\ \text{m/s}$.)
  • 6 The radius of a hydrogen atom is about $0.53\ \text{Å}$ and that of a proton about $0.84\ \text{fm}$. How many times larger is the atom?
  • 7 Using $1\ \text{u}=1.66\times10^{-27}\ \text{kg}$ and $N_A=6.02\times10^{23}\ \text{mol}^{-1}$, find the mass of one mole of carbon-12 atoms ($12\ \text{u}$ each). Comment.
  • 8 A star cluster is $50\ \text{pc}$ away. Express its distance in light years and in metres.
  • 9 Express a pressure of $1\ \text{atm}=1.013\times10^5\ \text{Pa}$ in bar and in torr ($1\ \text{torr}=133.3\ \text{Pa}$).
1 $54\div3.6=15\ \text{m/s}$; $25\times3.6=90\ \text{km/h}$.
2 $2.70\times10^{-3}\ \text{kg}\div10^{-6}\ \text{m}^3=2.70\times10^3\ \text{kg/m}^3$ (3 s.f. kept).
3 $1\ \text{m}^3=1000\ \text{L}$ (since $1\ \text{L}=10^{-3}\ \text{m}^3$) $=10^6\ \text{cm}^3$.
4 $E=1.5\ \text{kW}\times\tfrac{40}{60}\ \text{h}=1.0\ \text{kWh}=3.6\times10^6\ \text{J}$.
5 $t=\dfrac{1.496\times10^{11}}{3.00\times10^8}=499\ \text{s}=8.31\ \text{min}$.
6 $\dfrac{0.53\times10^{-10}}{0.84\times10^{-15}}=6.3\times10^4$ — the atom is mostly empty space.
7 $12\times1.66\times10^{-27}\times6.02\times10^{23}=1.20\times10^{-2}\ \text{kg}=12.0\ \text{g}$: the molar mass in grams equals the atomic mass in u, which is how the two units were chosen.
8 $50\times3.26=163\ \text{ly}$ ($1.6\times10^2\ \text{ly}$ to 2 s.f.); $50\times3.086\times10^{16}=1.5\times10^{18}\ \text{m}$.
9 $1.013\ \text{bar}$; $\dfrac{1.013\times10^5}{133.3}=760\ \text{torr}$ — the familiar $760\ \text{mm}$ of mercury.
III
Least count, significant figures and order of magnitude.
  • 1 In a Vernier calliper $10$ VSD $=9$ MSD and $1\ \text{MSD}=0.5\ \text{mm}$. Find the least count.
  • 2 A Vernier has $50$ VSD $=49$ MSD with $1\ \text{MSD}=1\ \text{mm}$. Find its least count, and the reading when the main scale shows $23\ \text{mm}$ and the $18$th Vernier division coincides.
  • 3 A screw gauge has pitch $1\ \text{mm}$ and $100$ circular divisions. Find its least count, and the reading for $3\ \text{mm}$ on the linear scale and $47$ circular divisions.
  • 4 The spindle of a screw gauge moves $2.5\ \text{mm}$ in $5$ complete rotations and its circular scale has $50$ divisions. Find the pitch and the least count.
  • 5 State the number of significant figures in: (a) $0.03040$ (b) $7.050\times10^{-3}$ (c) $6.02\times10^{23}$ (d) $200.0$ (e) $0.0006$ (f) $1.0001$.
  • 6 The radius of the Earth is "6400 km", known to 3 s.f. Write it unambiguously in km and in m.
  • 7 Using $0.5\lt a\le5$, give the order of magnitude of: (a) $c=3.0\times10^8\ \text{m/s}$ (b) the mass of the Earth, $5.97\times10^{24}\ \text{kg}$ (c) the radius of a hydrogen atom, $5.3\times10^{-11}\ \text{m}$ (d) one year, $3.16\times10^7\ \text{s}$.
  • 8 A student measures a book with a metre rule and writes "12 cm". The end of the book was exactly at a centimetre mark. How should the reading be written, and why?
1 $\text{LC}=\dfrac{0.5\ \text{mm}}{10}=0.05\ \text{mm}$.
2 $\text{LC}=\dfrac{1\ \text{mm}}{50}=0.02\ \text{mm}$; reading $=23+18\times0.02=23.36\ \text{mm}$.
3 $\text{LC}=\dfrac{1}{100}=0.01\ \text{mm}$; reading $=3+47\times0.01=3.47\ \text{mm}$.
4 Pitch $=\dfrac{2.5}{5}=0.5\ \text{mm}$; $\text{LC}=\dfrac{0.5}{50}=0.01\ \text{mm}$.
5 (a) 4 (b) 4 (c) 3 (d) 4 (e) 1 (f) 5.
6 $6.40\times10^3\ \text{km}=6.40\times10^6\ \text{m}$.
7 (a) $3.0\times10^8$, $a=3.0$: order $8$. (b) $0.597\times10^{25}$: order $25$. (c) $0.53\times10^{-10}$: order $-10$. (d) $3.16\times10^7$: order $7$.
8 The least count is $1\ \text{mm}=0.1\ \text{cm}$, so the reading is known to the first decimal place: $12.0\ \text{cm}$ (3 s.f.). Writing "12 cm" throws away a digit that was actually measured.
IV
Calculations, rounding and applications.
  • 1 Round to 3 significant figures: (a) $2.7462$ (b) $4.135$ (c) $4.125$ (d) $6.0251$ (e) $0.0098750$.
  • 2 Evaluate $3.0\times2.468$ to the correct significant figures.
  • 3 Evaluate $12.75+3.2+0.065$ correctly.
  • 4 Evaluate $7.82-7.6$ and state how many significant figures the result has.
  • 5 Evaluate $0.0425\div1.25$ correctly.
  • 6 Find the area of a circle of radius $3.50\ \text{cm}$.
  • 7 Find the volume of a cube of edge $2.10\ \text{cm}$.
  • 8 A rectangle measures $16.24\ \text{cm}$ by $8.3\ \text{cm}$. Find its perimeter.
  • 9 (Modelling) A sprinter covers a $100.0\ \text{m}$ track (measured with a steel tape) in $12.36\ \text{s}$. Find the average speed in $\text{m/s}$ and in $\text{km/h}$.
  • 10 (Modelling) A ream of $120$ identical sheets is $1.34\ \text{cm}$ thick, and each sheet is $25.0\ \text{cm}\times18.6\ \text{cm}$. Find the thickness and the volume of one sheet. Why does stacking help?
1 (a) $2.75$ (b) $4.14$ (exact half, $3$ is odd: raise) (c) $4.12$ (exact half, $2$ is even: keep) (d) $6.03$ (dropped part $51$ is more than half) (e) $0.00988$ (exact half, $7$ odd: raise).
2 $7.404\to7.4$ (2 s.f., set by $3.0$).
3 $16.015\to16.0$ (one decimal place, set by $3.2$).
4 $0.22\to0.2$ (one decimal place): a single significant figure.
5 $0.034$ to 3 s.f. is $0.0340$.
6 $\pi(3.50)^2=38.48\to38.5\ \text{cm}^2$.
7 $(2.10)^3=9.261\to9.26\ \text{cm}^3$.
8 Sum first: $16.24+8.3=24.54$; then $\times2$ (exact): $49.08\to49.1\ \text{cm}$ (one decimal place).
9 $v=\dfrac{100.0}{12.36}=8.091\ \text{m/s}$ (4 s.f.); $\times3.6$ (exact) $=29.13\ \text{km/h}$.
10 $t=\dfrac{1.34}{120}=0.0112\ \text{cm}$ ($120$ is a count, so exact; 3 s.f.). Volume $=25.0\times18.6\times0.01117=5.19\ \text{cm}^3$. Stacking turns a thickness far below the least count of a ruler into one that the ruler can measure to three figures.
🎯 Exam corner JEE Main · MCQJEE Main · Numerical

E1. JEE Main · MCQ Which of the following has the largest number of significant figures? (A) $0.007050$ (B) $7.05\times10^{-3}$ (C) $70.5$ (D) $0.07$

Count (A) leading zeros do not count, the trailing zero after the decimal point does: $7,0,5,0$ — 4. (B) 3. (C) 3. (D) 1.
Answer (A).
⏱ Shortcut Write each in scientific notation: $7.050\times10^{-3}$, $7.05\times10^{-3}$, $7.05\times10^{1}$, $7\times10^{-2}$ — the digit count of the mantissa is the answer.

E2. JEE Main · Numerical In a Vernier calliper $25$ Vernier divisions coincide with $24$ main-scale divisions, and one main-scale division is $0.5\ \text{mm}$. When a sphere is held in the jaws the main scale reads $12.5\ \text{mm}$ and the $13$th Vernier division coincides with a main-scale mark. The diameter of the sphere is $x\times10^{-2}\ \text{mm}$. Find $x$. Give the answer to the nearest integer.

LC $n=25$: $\text{LC}=\dfrac{0.5\ \text{mm}}{25}=0.02\ \text{mm}$.
Reading $12.5+13\times0.02=12.5+0.26=12.76\ \text{mm}$.
Answer $12.76\ \text{mm}=1276\times10^{-2}\ \text{mm}$, so $x=1276$.

E3. JEE Main · MCQ Two lengths are measured as $4.235\ \text{m}$ and $1.5\ \text{m}$. Their sum, written with the correct number of significant figures, is (A) $5.735\ \text{m}$ (B) $5.74\ \text{m}$ (C) $5.7\ \text{m}$ (D) $6\ \text{m}$

Rule In a sum the result keeps the fewest decimal places — one, from $1.5\ \text{m}$.
Round $5.735\to5.7$ (the dropped part $0.035$ is less than half of $0.1$).
Answer (C).
⏱ Shortcut (D) is what you get by wrongly using the "fewest significant figures" rule (2 s.f.) and then over-rounding; for sums, count decimal places only.

E4. JEE Main · Numerical A screw gauge has pitch $0.5\ \text{mm}$ and $50$ divisions on its circular scale. For a wire the linear scale reads $3.5\ \text{mm}$ and the $28$th circular division lies on the reference line. Find the area of cross-section of the wire in $\text{mm}^2$. Give the answer to the nearest integer.

Diameter $\text{LC}=\dfrac{0.5}{50}=0.01\ \text{mm}$; $d=3.5+28\times0.01=3.78\ \text{mm}$ (3 s.f.).
Area $A=\dfrac{\pi d^2}{4}=\dfrac{\pi(3.78)^2}{4}=11.2\ \text{mm}^2$ (3 s.f., like $d$).
Answer $11$.

E5. JEE Main · MCQ The energy of $1\ \text{kWh}$ expressed in electronvolts is about (A) $3.6\times10^{6}\ \text{eV}$ (B) $2.25\times10^{25}\ \text{eV}$ (C) $5.8\times10^{-13}\ \text{eV}$ (D) $2.25\times10^{22}\ \text{eV}$ (take $1\ \text{eV}=1.602\times10^{-19}\ \text{J}$)

Joules $1\ \text{kWh}=10^3\ \text{W}\times3600\ \text{s}=3.6\times10^6\ \text{J}$.
eV $\dfrac{3.6\times10^6}{1.602\times10^{-19}}=2.25\times10^{25}\ \text{eV}$.
Answer (B).
⏱ Shortcut The electronvolt is tiny, so the number of eV must be huge: (A) forgets to convert and (C) divides the wrong way; (D) uses $1\ \text{W}$ instead of $1\ \text{kW}$.

E6. JEE Main · Numerical The density of a metal is $8.0\ \text{g/cm}^3$. In a system of units in which the unit of length is $10\ \text{cm}$ and the unit of mass is $100\ \text{g}$ (the unit of time is unchanged), what is the numerical value of this density? Give the answer to the nearest integer.

Factors of one $8.0\ \dfrac{\text{g}}{\text{cm}^3}\times\dfrac{1\ \text{(new mass unit)}}{100\ \text{g}}\times\left(\dfrac{10\ \text{cm}}{1\ \text{(new length unit)}}\right)^3$.
Evaluate $8.0\times\dfrac{1}{100}\times1000=80$.
Answer $80$.
⏱ Shortcut A bigger mass unit makes the number smaller ($\div100$); a bigger length unit holds $1000$ times the volume, making the number larger ($\times1000$). Section 1.2 turns this into a one-line formula using dimensions.
🔬 Research–Teaching NexusResearch-tutored · optional, about 45 minutes

Research question. How thick is one sheet of paper — and how many significant figures can you honestly claim with a ruler, a Vernier calliper and a screw gauge?

Why it matters. Thickness far below the least count of the tool at hand is a daily problem in industry. Paper mills control sheet thickness (called "caliper") to a few micrometres; chip makers measure films of a few nanometres; pharmaceutical companies check the coating on tablets. The trick of measuring many identical layers at once, and the question of how many digits the result deserves, are exactly the ideas of this section.

What to do.

  1. Take a fresh pack of office paper. With a metre rule, measure the thickness of stacks of $50$, $100$, $200$ and $500$ sheets, pressing them flat in the same way each time. Record each reading to the least count.
  2. Repeat with a Vernier calliper for stacks of $10$, $20$ and $50$ sheets, and with a screw gauge for $1$, $2$ and $5$ sheets.
  3. For every measurement, find the thickness of one sheet with the correct number of significant figures (the number of sheets is exact).
  4. Plot thickness of one sheet against the number of sheets for each instrument. Which method gives the most significant figures? Where do the methods disagree, and why (air between sheets, squeezing by the jaws)?
  5. Compare with the specification on the pack: grammage (for example $80\ \text{g/m}^2$). Use your thickness to estimate the density of paper in $\text{kg/m}^3$.

Tools: Pack of paper, metre rule, Vernier calliper, screw gauge (a school laboratory has all three); a spreadsheet for the table and the graph.

Hand in: A table of readings and per-sheet thickness with correct significant figures, your graph, your best value with a one-sentence justification of its number of digits, and your estimate of the density of paper.

Going further. A human hair is thinner than one sheet. Design a way to measure its diameter with a ruler alone (wind it many times round a pencil), and compare with a screw-gauge reading.

Instructor note: ordinary $80\ \text{g/m}^2$ office paper is about $0.10\ \text{mm}$ thick, so a $500$-sheet ream is close to $50\ \text{mm}$; a metre rule then gives the thickness of one sheet to about 2–3 s.f. ($0.100\ \text{mm}$ if the ream reads $50.0\ \text{mm}$), better than a single screw-gauge reading of a soft sheet, which is squeezed by the spindle. The density estimate comes out near $800\ \text{kg/m}^3$.

🧪 Self-check quiz

0/5 correct

Q1. Which of the following is an SI base unit?

Q2. The number of significant figures in $0.004050$ is

Q3. Rounded to three significant figures by the rule used in JEE Main, $2.345$ becomes

Q4. A screw gauge has a pitch of $1\ \text{mm}$ and $100$ divisions on its circular scale. Its least count is

Q5. A length of $12.4\ \text{m}$ is multiplied by a measured factor of $0.30$. The result, with correct significant figures, is