Chapter 8 · Thermodynamics

8.2 Thermodynamic Processes

Four standard ways to change the state of an ideal gas — at constant volume, at constant pressure, at constant temperature and with no heat exchange — each with its own work, heat and internal-energy change; then cycles, in which the gas returns to its start and the net work is the area enclosed on the $p$–$V$ diagram.

A diesel engine has no spark plug. Air is squeezed into a cylinder so quickly that no heat has time to escape, and its temperature shoots up past $600\ ^\circ\text{C}$ — hot enough to ignite the fuel sprayed into it. A scuba tank filled slowly at a dive shop, in contrast, stays near room temperature, because the heat of compression leaks away as fast as it is produced. A pressure cooker heats its contents at (almost) constant volume; a hot-air balloon heats air at constant pressure. The same gas, the same first law — but four very different results, depending on how the change is carried out.

In Section 8.1 we met the first law, $Q=\Delta U+W$, and learned to read work as the area under a path on the $p$–$V$ diagram. Here we apply them to the four standard processes of an ideal gas — isochoric (constant volume), isobaric (constant pressure), isothermal (constant temperature) and adiabatic (no heat exchanged) — introducing the molar heat capacities $C_V$ and $C_p$ and their ratio $\gamma$ as we need them. We finish with cyclic processes, the basis of every heat engine studied in Section 8.3. Throughout, $W$ is the work done by the gas, so $\Delta U=Q-W$, and every process is quasi-static unless we say otherwise.

Isochoric and isobaric processes and the molar heat capacities

How much heat does it take to warm a gas by one kelvin? For a solid or a liquid the answer is a single number, the specific heat capacity of Section 7.5. For a gas it depends on what you let the gas do while it is being heated: if it is allowed to expand, part of the heat leaves again as work, and more heat is needed for the same rise in temperature.

📘 Definition 8.6 — Molar heat capacities of a gas

The molar heat capacity of a gas in a given process is the heat needed per mole per kelvin of temperature rise in that process:

$$C=\frac{1}{n}\,\frac{dQ}{dT}\qquad(\text{unit }\text{J mol}^{-1}\text{K}^{-1}).$$

The two standard values are $C_V$, measured at constant volume, and $C_p$, measured at constant pressure. Their ratio is written $\gamma=C_p/C_V$ (always greater than 1). For an ideal gas near room temperature: monatomic $C_V=\tfrac32R$, $C_p=\tfrac52R$, $\gamma=\tfrac53$; diatomic $C_V=\tfrac52R$, $C_p=\tfrac72R$, $\gamma=\tfrac75=1.4$ (air is nearly diatomic). Section 9.2 derives these values from kinetic theory.

📘 Definition 8.7 — The four standard processes
  • Isochoric (isovolumetric): the volume is constant — a gas in a rigid, sealed container.
  • Isobaric: the pressure is constant — a gas under a freely moving piston with a fixed load.
  • Isothermal: the temperature is constant — a gas in a diathermic container in good contact with a large body at fixed temperature (a heat reservoir), changed slowly.
  • Adiabatic: no heat is exchanged, $Q=0$ — a gas in an insulated container, or a change so fast that heat has no time to flow.

Isochoric process. With $V$ fixed, the gas does no work: $W=0$. Every joule of heat goes into internal energy, $Q=\Delta U=nC_V\Delta T$, and the pressure rises in proportion to the absolute temperature, $p/T=$ constant. This is why $C_V$ is the constant that appears in $\Delta U=nC_V\Delta T$: at constant volume the heat supplied is the change in internal energy. On a $p$–$V$ diagram the process is a vertical line, with no area under it.

Isobaric process. With $p$ fixed, $V/T$ is constant (Charles's law), and the work done is the rectangle under a horizontal line:

$$W=p\,(V_2-V_1)=nR\,(T_2-T_1),$$

using $pV=nRT$ at both ends. The internal energy changes by $nC_V\Delta T$ — the same as for any other process with this $\Delta T$ — so the first law gives $Q=nC_V\Delta T+nR\Delta T$. But by definition $Q=nC_p\Delta T$ at constant pressure, which proves an important relation.

📐 Result 8.6 — Mayer's relation and the isobaric process

For an ideal gas,

$$C_p-C_V=R .$$

In an isobaric change of $n$ moles by $\Delta T$: $\ Q=nC_p\Delta T$, $\ \Delta U=nC_V\Delta T$, $\ W=p\Delta V=nR\Delta T$, so that

$$Q:\Delta U:W=C_p:C_V:R,\qquad \frac{W}{Q}=\frac{R}{C_p}=1-\frac1\gamma .$$

A monatomic gas heated at constant pressure turns $\tfrac25$ of the heat into work; a diatomic gas, $\tfrac27$.

✏️ Example 1 — Heating nitrogen at constant pressure
$2.0\ \text{mol}$ of nitrogen (diatomic ideal gas) are heated at constant pressure from $300\ \text{K}$ to $400\ \text{K}$. Find (a) the heat supplied, (b) the increase in internal energy, (c) the work done by the gas, and (d) the fraction of the heat that is converted into work.
(a) $Q=nC_p\Delta T=2.0\times\tfrac72\times8.31\times100=5817\ \text{J}\approx5.82\ \text{kJ}$.
(b) $\Delta U=nC_V\Delta T=2.0\times\tfrac52\times8.31\times100=4155\ \text{J}\approx4.16\ \text{kJ}$.
(c) $W=nR\Delta T=2.0\times8.31\times100=1662\ \text{J}$. Check: $Q-\Delta U=5817-4155=1662\ \text{J}$ ✓.
(d) $W/Q=R/C_p=2/7=0.286$, i.e. $28.6\%$.
✏️ Example 2 — Identifying a gas from its heat capacities
Heating $1.0\ \text{mol}$ of an ideal gas through $10\ \text{K}$ needs $208\ \text{J}$ at constant volume and $291\ \text{J}$ at constant pressure. (a) Find $C_V$, $C_p$ and $\gamma$. (b) Check Mayer's relation and decide whether the gas is monatomic or diatomic. (c) If instead $500\ \text{J}$ is supplied to $1.0\ \text{mol}$ of this gas, find the temperature rise at constant volume and at constant pressure.
(a) $C_V=\dfrac{208}{1.0\times10}=20.8\ \text{J mol}^{-1}\text{K}^{-1}$; $C_p=29.1\ \text{J mol}^{-1}\text{K}^{-1}$; $\gamma=\dfrac{29.1}{20.8}=1.40$.
(b) $C_p-C_V=8.3\ \text{J mol}^{-1}\text{K}^{-1}\approx R$ ✓. $C_V/R=2.50$ and $\gamma=1.40$: a diatomic gas.
(c) $\Delta T_V=\dfrac{500}{20.8}=24.0\ \text{K}$; $\ \Delta T_p=\dfrac{500}{29.1}=17.2\ \text{K}$ — smaller, because at constant pressure $\tfrac27$ of the heat leaves as work.

A monatomic ideal gas is heated at constant pressure. What fraction of the heat supplied is used to increase its internal energy?

Isothermal processes

In an isothermal process the gas is kept in contact with a heat reservoir and changed slowly, so that its temperature never drifts from the reservoir's. For an ideal gas $pV=nRT$ with $T$ fixed gives Boyle's law, $pV=$ constant: on a $p$–$V$ diagram the process follows a rectangular hyperbola, an isotherm. Isotherms for higher temperatures lie further from the origin.

Because $U$ of an ideal gas depends only on $T$, $\Delta U=0$ in an isothermal process, and the first law gives $Q=W$: all the heat taken in is given out as work (in an expansion), or all the work done on the gas leaves it as heat (in a compression). The work is the area under the hyperbola:

$$W=\int_{V_1}^{V_2}\frac{nRT}{V}\,dV=nRT\ln\frac{V_2}{V_1}.$$
📐 Result 8.7 — Isothermal process of an ideal gas

For $n$ moles of an ideal gas at constant temperature $T$, changing quasi-statically from $(p_1,V_1)$ to $(p_2,V_2)$:

$$p_1V_1=p_2V_2,\qquad \Delta U=0,\qquad Q=W=nRT\ln\frac{V_2}{V_1}=nRT\ln\frac{p_1}{p_2}.$$

$W\gt0$ (heat absorbed) for an expansion, $W\lt0$ (heat given out) for a compression. The slope of an isotherm is $\dfrac{dp}{dV}=-\dfrac pV$. Since $\Delta T=0$ while $Q\ne0$, the molar heat capacity in an isothermal process is infinite.

Useful values: $\ln2=0.693$, $\ln3=1.099$, $\ln10=2.303$ (so $\ln x=2.303\log_{10}x$). Note that "isothermal" does not mean "no heat": heat must flow, in fact exactly as much as the work done, to hold the temperature steady.

✏️ Example 3 — Isothermal compression
$1.0\ \text{mol}$ of an ideal gas at $300\ \text{K}$ is compressed slowly and isothermally from $20\ \text{L}$ to $5.0\ \text{L}$. Find (a) the final pressure, (b) the work done by the gas, (c) the heat exchanged and its direction, (d) $\Delta U$.
(a) $p_2=\dfrac{nRT}{V_2}=\dfrac{8.31\times300}{5.0\times10^{-3}}=4.99\times10^5\ \text{Pa}$ (four times the initial $1.25\times10^5\ \text{Pa}$).
(b) $W=nRT\ln\dfrac{V_2}{V_1}=8.31\times300\times\ln0.25=2493\times(-1.386)=-3.46\times10^3\ \text{J}$: $3.46\ \text{kJ}$ of work is done on the gas.
(c) $Q=W=-3.46\ \text{kJ}$: the gas gives out $3.46\ \text{kJ}$ of heat to the reservoir.
(d) $\Delta U=0$: the temperature is unchanged.

An ideal gas expands isothermally. Which statement is correct?

Adiabatic processes

Now insulate the cylinder, or work so fast that heat has no time to flow: $Q=0$. The first law becomes $\Delta U=-W$. An expanding gas does work at the expense of its own internal energy and cools; a compressed gas warms. That is why air escaping from a tyre valve feels cold, why a bicycle pump heats up, why rising air in the atmosphere cools (it expands as the pressure falls) until its water vapour condenses into clouds, and why a diesel engine can ignite its fuel by compression alone.

Derivation of the adiabatic equation. In a small quasi-static step with $dQ=0$, the first law gives $nC_V\,dT=-p\,dV$. Differentiating $pV=nRT$ gives $p\,dV+V\,dp=nR\,dT=-\dfrac{R}{C_V}\,p\,dV$. Hence

$$V\,dp=-\left(1+\frac{R}{C_V}\right)p\,dV=-\gamma\,p\,dV\quad\Longrightarrow\quad \frac{dp}{p}=-\gamma\,\frac{dV}{V},$$

using $C_V+R=C_p$. Integrating, $\ln p=-\gamma\ln V+\text{constant}$, that is $pV^\gamma=$ constant.

📐 Law 8.8 — Reversible adiabatic process of an ideal gas

For an ideal gas undergoing a quasi-static adiabatic change, with $\gamma=C_p/C_V$ constant,

$$pV^{\gamma}=\text{constant},\qquad TV^{\gamma-1}=\text{constant},\qquad \frac{T^{\gamma}}{p^{\gamma-1}}=\text{constant}.$$

(The second and third forms follow by eliminating $p$ or $V$ with $pV=nRT$.) The slope of an adiabat is $\dfrac{dp}{dV}=-\gamma\dfrac pV$ — steeper than the isotherm through the same point by the factor $\gamma$. These relations do not apply to a free expansion, which is adiabatic but far from quasi-static.

📐 Result 8.9 — Work in an adiabatic process

From $(p_1,V_1,T_1)$ to $(p_2,V_2,T_2)$ with $Q=0$:

$$W=-\Delta U=nC_V(T_1-T_2)=\frac{nR(T_1-T_2)}{\gamma-1}=\frac{p_1V_1-p_2V_2}{\gamma-1}.$$

The same result comes from integrating $p=KV^{-\gamma}$: $\displaystyle\int_{V_1}^{V_2}KV^{-\gamma}dV=\frac{K(V_2^{1-\gamma}-V_1^{1-\gamma})}{1-\gamma}$ with $KV^{1-\gamma}=pV$.

Isotherm or adiabat? Start two identical samples at the same state and expand both to twice the volume. In the isothermal expansion heat flows in and keeps $T$ up; in the adiabatic one no heat enters, $T$ falls, and the pressure falls faster ($p\propto V^{-\gamma}$ instead of $V^{-1}$). So the adiabat lies below the isotherm for an expansion — less area, less work — and above it for a compression, where more work is needed. Interactive 1 shows both curves through the starting point.

✏️ Example 4 — The diesel engine
In a diesel engine, air ($\gamma=1.4$) at $300\ \text{K}$ and $1.0\times10^5\ \text{Pa}$ is compressed adiabatically to $\tfrac1{16}$ of its volume. Find (a) the final temperature, (b) the final pressure, (c) the work done on $1.0\ \text{mol}$ of air. Take $16^{0.4}=3.03$.
Find the final temperature (a) first:
(a) $T_2=T_1\left(\dfrac{V_1}{V_2}\right)^{\gamma-1}=300\times16^{0.4}=300\times3.03=909\ \text{K}$ (about $636\ ^\circ\text{C}$ — above the ignition temperature of diesel fuel).
(b) $p_2=p_1\left(\dfrac{V_1}{V_2}\right)^{\gamma}=1.0\times10^5\times16\times3.03=4.85\times10^6\ \text{Pa}$ (about $48\ \text{atm}$).
(c) $W=nC_V(T_1-T_2)=1.0\times\tfrac52\times8.31\times(300-909)=-1.27\times10^4\ \text{J}$: about $12.7\ \text{kJ}$ of work is done on the air.
Check $\dfrac{p_2V_2}{p_1V_1}=\dfrac{48.5}{16}=3.03=\dfrac{T_2}{T_1}$ ✓ — the ideal-gas equation holds at both ends.

In Interactive 1 choose a monatomic gas and set $V_2/V_1=2.0$. Compare the isothermal and the adiabatic expansion. Which does more work, and what is the final temperature in the adiabatic case?

Isothermal, $V_2/V_1=2.0$: the readouts show $W=Q=693\ \text{J}$ ($=p_1V_1\ln2$ with $p_1V_1=1000\ \text{J}$), $\Delta U=0$, $p_2=50\ \text{kPa}$. Adiabatic (monatomic): $W=555\ \text{J}$, $Q=0$, $\Delta U=-555\ \text{J}$, $p_2=31.5\ \text{kPa}$ and $T_2=189\ \text{K}$ $\left(=300\times2^{-2/3}\right)$. No heat enters in the adiabatic case, so the gas cools and its pressure falls faster: the path runs below the isotherm and encloses less area. ($150\ \text{K}$ would be halving $T$, as if $pV$ halved at constant pressure.) For a diatomic gas the adiabatic numbers become $605\ \text{J}$ and $227\ \text{K}$.
Interactive 1 — Four Processes on the p–V Diagram

An ideal gas starts at state 1: $100\ \text{kPa}$, $10.0\ \text{L}$, $300\ \text{K}$ (so $p_1V_1=1000\ \text{J}$, $n=0.401\ \text{mol}$). Choose a process and the ratio $r$ (the volume ratio $V_2/V_1$; for the isochoric process, the pressure ratio $p_2/p_1$), then press Play. The dashed curves are the isotherm and the adiabat through state 1; the shaded area is the work done by the gas.

2.0
final state—
$T_2$—
$W$ (shaded)—
$\Delta U$ and $Q$—

At a given point on the $p$–$V$ diagram of an ideal gas with $\gamma=1.4$, the slope of the adiabat compared with the slope of the isotherm through the same point is

Cyclic processes and the p–V diagram

An engine cannot keep expanding a gas forever; it has to bring the gas back to its starting state and start again. A process in which the system returns to its initial state is a cyclic process, drawn as a closed loop on the $p$–$V$ diagram.

📘 Definition 8.8 — Cyclic process

A cyclic process is a sequence of processes that returns a system to its initial state. Over one complete cycle every state variable returns to its starting value; in particular $\Delta U_\text{cycle}=0$.

📐 Result 8.10 — Work and heat in a cycle

For any cyclic process,

$$\Delta U=0,\qquad Q_\text{net}=W_\text{net}=\text{area enclosed by the loop on the }p\text{–}V\text{ diagram}.$$

The net work done by the gas is positive if the loop is traversed clockwise (with $p$ up and $V$ to the right) and negative if it is traversed anticlockwise. $Q_\text{net}$ is the heat absorbed minus the heat given out over the cycle; it is not zero, even though $\Delta U$ is.

Why the area? Going along the upper part of a clockwise loop the gas expands at high pressure, doing a large positive work (the area under the upper curve). Coming back along the lower part it is compressed at low pressure, and a smaller amount of work is done on it (the area under the lower curve). The difference is the area between the curves — the area inside the loop. Run the loop the other way and the gas is expanded at low pressure and compressed at high pressure: net work is done on it, as in a refrigerator.

🧭 Problem-solving strategy — Working round a cycle
  1. Label the corners and find $p$, $V$ (and $T$ from $pV=nRT$) at each one.
  2. For each leg write $W$ (zero if isochoric, $p\Delta V$ if isobaric, $nRT\ln(V_b/V_a)$ if isothermal, the trapezium for a straight line) and $\Delta U=nC_V\Delta T$ — for a monatomic gas $\tfrac32\Delta(pV)$, for a diatomic gas $\tfrac52\Delta(pV)$.
  3. Get $Q=\Delta U+W$ for each leg; the positive ones add up to the heat absorbed, the negative ones to the heat given out.
  4. Check: $\sum\Delta U=0$ and $\sum Q=\sum W=$ the enclosed area, with the sign given by the direction.
  5. If the cycle is drawn on a $V$–$T$ or $p$–$T$ diagram, first identify each leg (a straight line through the origin of a $V$–$T$ graph is an isobar; of a $p$–$T$ graph, an isochore), then redraw the cycle on $p$–$V$ axes to find the direction.
✏️ Example 5 — A rectangular cycle, leg by leg
A monatomic ideal gas is taken round the cycle $A\to D\to C\to B\to A$, where $A=(100\ \text{kPa},\ 1.0\ \text{L})$, $D=(300\ \text{kPa},\ 1.0\ \text{L})$, $C=(300\ \text{kPa},\ 3.0\ \text{L})$, $B=(100\ \text{kPa},\ 3.0\ \text{L})$. (a) Is the cycle clockwise? Find the net work. (b) Find $W$, $\Delta U$ and $Q$ for each leg. (c) Find the total heat absorbed and the total heat given out.
(a) Up the left side, right along the top, down the right side, back along the bottom: clockwise. $W_\text{net}=+(300-100)\times(3.0-1.0)=+400\ \text{J}$ ($\text{kPa}\times\text{L}=\text{J}$).
(b) $A\to D$ (isochoric): $W=0$, $\Delta U=\tfrac32(300-100)=300\ \text{J}$, $Q=+300\ \text{J}$. $D\to C$ (isobaric): $W=300\times2.0=600\ \text{J}$, $\Delta U=\tfrac32(900-300)=900\ \text{J}$, $Q=+1500\ \text{J}$. $C\to B$ (isochoric): $W=0$, $\Delta U=Q=-900\ \text{J}$. $B\to A$ (isobaric): $W=100\times(-2.0)=-200\ \text{J}$, $\Delta U=\tfrac32(100-300)=-300\ \text{J}$, $Q=-500\ \text{J}$.
(c) Absorbed: $300+1500=1800\ \text{J}$; given out: $900+500=1400\ \text{J}$. Net $Q=400\ \text{J}=W_\text{net}$ ✓.
Check $\sum\Delta U=300+900-900-300=0$ ✓. The gas must absorb $1800\ \text{J}$ to deliver $400\ \text{J}$ of net work — why this is unavoidable is the subject of Section 8.3.
✏️ Example 6 — A cycle with an isothermal leg
$1.0\ \text{mol}$ of a monatomic ideal gas at state $A$ ($T_A=600\ \text{K}$, volume $V_0$) expands isothermally to $B$ (volume $2V_0$), is then compressed at constant pressure to $C$ (volume $V_0$), and finally heated at constant volume back to $A$. (a) Find the temperature at $C$. (b) Find the work done in each leg and the net work. (c) Find the heat exchanged in each leg and check the first law for the cycle. Take $\ln2=0.693$.
Find the net work done by the gas (b) first:
(a) $T_B=T_A=600\ \text{K}$. From $B$ to $C$ the pressure is constant, so $V/T$ is constant: $T_C=600\times\dfrac{V_0}{2V_0}=300\ \text{K}$.
(b) $W_{AB}=RT_A\ln2=8.31\times600\times0.693=3456\ \text{J}$; $\ W_{BC}=R(T_C-T_B)=8.31\times(-300)=-2493\ \text{J}$; $\ W_{CA}=0$. $W_\text{net}=3456-2493=963\ \text{J}$.
(c) $Q_{AB}=W_{AB}=+3456\ \text{J}$ ($\Delta U=0$). $Q_{BC}=C_p\Delta T=\tfrac52\times8.31\times(-300)=-6233\ \text{J}$. $Q_{CA}=C_V\Delta T=\tfrac32\times8.31\times300=+3740\ \text{J}$. $\sum Q=3456-6233+3740=963\ \text{J}=W_\text{net}$ ✓.
⏱ Shortcut The net work is all you need for most cycle MCQs: $W_\text{net}=RT_A\ln2-R\cdot\tfrac{T_A}{2}=RT_A(\ln2-\tfrac12)=0.193\,RT_A$. Positive, since the loop $A\to B\to C$ is clockwise ($A$ top left, $B$ lower right, $C$ lower left).

In Interactive 2 choose the rectangle with $V_2/V_1=3$ and $p_2/p_1=3$ — the cycle of Example 5 — but run it anticlockwise. What are the net work done by the gas and the heat absorbed per cycle?

Rectangle, $V_2/V_1=3$, $p_2/p_1=3$, anticlockwise: the readouts show $W_\text{net}=-400\ \text{J}$, heat absorbed $1400\ \text{J}$, heat given out $1800\ \text{J}$ and $\Delta U_\text{cycle}=0$. Reversing the direction reverses every leg: the gas now expands at $100\ \text{kPa}$ ($W=+200\ \text{J}$) and is compressed at $300\ \text{kPa}$ ($W=-600\ \text{J}$), and the legs that absorbed heat now give it out. $\Delta U=0$ over a cycle, but the work and the net heat are the enclosed area, not zero.
Interactive 2 — Round a Cycle: Area, Direction and Heat

A monatomic ideal gas is taken round a cycle starting from $A$ ($100\ \text{kPa}$, $1.0\ \text{L}$; for the isothermal cycle $A$ is at $p_2$). Choose the shape, the direction and the ratios $V_2/V_1$ and $p_2/p_1$, then press Play. Legs that absorb heat are drawn red, legs that give out heat blue; the table lists $W$ and $Q$ for each leg. The shaded area is the net work.

3.03.0
net work $W_\text{net}$—
heat absorbed—
heat given out—
$\Delta U$ over cycle—
⚠️ JEE Main traps

1. Using $pV^\gamma=$ constant where it does not apply. It holds only for a quasi-static adiabatic change of an ideal gas. A free expansion is adiabatic too, but $T$ stays constant and $pV^\gamma$ is not conserved.

2. Celsius in the formulas. $TV^{\gamma-1}=$ const, $pV=nRT$ and $V/T=$ const all need kelvin. Convert first; convert back only at the end.

3. Mixing up "isothermal" and "adiabatic". Isothermal: $\Delta T=0$, $\Delta U=0$, $Q=W\ne0$. Adiabatic: $Q=0$, $\Delta U=-W$, $T$ changes. The adiabat is steeper by the factor $\gamma$.

4. Direction of a cycle. Clockwise on $p$–$V$ axes means positive net work by the gas. On a $V$–$p$ graph (axes swapped) or a $V$–$T$ graph, redraw on $p$–$V$ axes before deciding. Over a cycle $\Delta U=0$ but $Q_\text{net}=W_\text{net}\ne0$.

5. Logarithms and ratios. $W_\text{iso}=nRT\ln(V_2/V_1)=nRT\ln(p_1/p_2)$ — note the pressure ratio is upside down; $\ln x=2.303\log_{10}x$. In $T_2=T_1(V_1/V_2)^{\gamma-1}$ the power is $\gamma-1$, in $p_2=p_1(V_1/V_2)^\gamma$ it is $\gamma$.

An ideal gas is taken round a closed loop that is traversed clockwise on a $p$–$V$ diagram (with $p$ on the vertical axis). Over one cycle

Exercises

Take $R=8.31\ \text{J mol}^{-1}\text{K}^{-1}$; for ideal gases $C_V=\tfrac32R$, $\gamma=\tfrac53$ (monatomic) and $C_V=\tfrac52R$, $\gamma=1.4$ (diatomic, and air) unless told otherwise. $W$ is the work done by the gas; all processes are quasi-static unless stated.

I
Isochoric and isobaric processes; $C_V$ and $C_p$.
  • 1 $3.0\ \text{mol}$ of helium are heated at constant volume from $300\ \text{K}$ to $350\ \text{K}$. Find the heat supplied.
  • 2 The same gas is heated through the same temperature range at constant pressure. Find the heat supplied and the work done.
  • 3 An ideal gas has $C_p=29.1\ \text{J mol}^{-1}\text{K}^{-1}$. Find $C_V$ and $\gamma$.
  • 4 A diatomic ideal gas absorbs $700\ \text{J}$ of heat at constant pressure. Find the work it does and its increase in internal energy.
  • 5 A diatomic gas expands at a constant $2.0\times10^5\ \text{Pa}$ from $5.0\ \text{L}$ to $7.5\ \text{L}$. Find $W$, $\Delta U$ and $Q$.
  • 6 A gas is heated in a sealed rigid steel cylinder. Why does it do no work? What happens to its pressure?
  • 7 Show that in an isobaric process of a monatomic ideal gas $Q:\Delta U:W=5:3:2$, and find the ratio for a diatomic gas.
  • 8 $1.0\ \text{mol}$ of an ideal gas is heated at constant pressure from $27\ ^\circ\text{C}$ to $127\ ^\circ\text{C}$. Find the work done.
1 $Q=nC_V\Delta T=3.0\times\tfrac32\times8.31\times50=1.87\times10^3\ \text{J}$.
2 $Q=nC_p\Delta T=3.0\times\tfrac52\times8.31\times50=3.12\times10^3\ \text{J}$; $W=nR\Delta T=1.25\times10^3\ \text{J}$.
3 $C_V=29.1-8.31=20.8\ \text{J mol}^{-1}\text{K}^{-1}$; $\gamma=29.1/20.8=1.40$.
4 $W=\tfrac27Q=200\ \text{J}$; $\Delta U=\tfrac57Q=500\ \text{J}$.
5 $W=p\Delta V=2.0\times10^5\times2.5\times10^{-3}=500\ \text{J}$; $\Delta U=nC_V\Delta T=\tfrac52\,p\Delta V=1250\ \text{J}$; $Q=1750\ \text{J}$.
6 The walls do not move, so no force acts through a displacement: $W=0$ and $Q=\Delta U$. The pressure rises in proportion to the kelvin temperature.
7 $Q:\Delta U:W=nC_p\Delta T:nC_V\Delta T:nR\Delta T=C_p:C_V:R$. Monatomic: $\tfrac52:\tfrac32:1=5:3:2$. Diatomic: $\tfrac72:\tfrac52:1=7:5:2$.
8 $W=nR\Delta T=1.0\times8.31\times100=831\ \text{J}$ (a temperature difference is the same in K and $^\circ\text{C}$).
II
Isothermal and adiabatic processes.
  • 1 $2.0\ \text{mol}$ of an ideal gas at $400\ \text{K}$ expand isothermally from $10\ \text{L}$ to $30\ \text{L}$. Find the work done and the heat absorbed.
  • 2 $1.0\ \text{mol}$ of an ideal gas at $300\ \text{K}$ is compressed isothermally from $1.0\times10^5\ \text{Pa}$ to $5.0\times10^5\ \text{Pa}$. Find the heat given out by the gas ($\ln5=1.609$).
  • 3 A monatomic ideal gas at $300\ \text{K}$ is compressed adiabatically to one-eighth of its volume. Find its final temperature.
  • 4 In part 3, by what factor does the pressure increase?
  • 5 $2.0\ \text{mol}$ of a diatomic gas expand adiabatically and cool from $400\ \text{K}$ to $300\ \text{K}$. Find the work done by the gas.
  • 6 Air at $1.0\times10^5\ \text{Pa}$ is compressed adiabatically to half its volume ($2^{1.4}=2.64$). Find the final pressure, and compare with an isothermal compression to the same volume.
  • 7 At the state $p=1.0\times10^5\ \text{Pa}$, $V=2.0\ \text{L}$, find the slopes $dp/dV$ of the isotherm and of the adiabat of air through that point.
  • 8 Explain why rising air cools and can form clouds, and why the air rushing out of a punctured tyre feels cold.
  • 9 Two identical samples of gas expand from the same state to the same final volume, one isothermally and one adiabatically. Which ends at the lower pressure, and which does more work? Sketch both on one $p$–$V$ diagram.
1 $W=nRT\ln3=2.0\times8.31\times400\times1.099=7.30\times10^3\ \text{J}$; $Q=W$ (since $\Delta U=0$).
2 $W=nRT\ln\dfrac{p_1}{p_2}=2493\times\ln0.2=-4.01\times10^3\ \text{J}$, so $Q=-4.01\ \text{kJ}$: the gas gives out $4.01\times10^3\ \text{J}$.
3 $T_2=300\times8^{2/3}=300\times4=1200\ \text{K}$.
4 $p_2/p_1=8^{5/3}=32$. (Check: $p_2V_2/p_1V_1=32/8=4=T_2/T_1$ ✓.)
5 $W=nC_V(T_1-T_2)=2.0\times\tfrac52\times8.31\times100=4155\ \text{J}\approx4.16\ \text{kJ}$.
6 $p_2=1.0\times10^5\times2^{1.4}=2.64\times10^5\ \text{Pa}$; isothermally only $2.0\times10^5\ \text{Pa}$ — the adiabatic compression also heats the gas.
7 Isotherm: $-\dfrac pV=-\dfrac{1.0\times10^5}{2.0\times10^{-3}}=-5.0\times10^7\ \text{Pa/m}^3$. Adiabat: $-\gamma\dfrac pV=-7.0\times10^7\ \text{Pa/m}^3$.
8 Rising air moves to lower pressure and expands; air is a poor conductor, so the expansion is nearly adiabatic and the air cools ($\Delta U=-W\lt0$), until water vapour condenses. Air leaving a tyre expands rapidly in the same way and cools.
9 The adiabatic sample ends at the lower pressure and lower temperature; its curve lies below the isotherm, so it does less work. The isothermal sample does more work, paid for by the heat it absorbs.
III
Cyclic processes.
  • 1 A gas is taken clockwise round a rectangle on the $p$–$V$ diagram with sides at $1.0\times10^5$ and $2.5\times10^5\ \text{Pa}$ and at $2.0$ and $5.0\ \text{L}$. Find the net work done by the gas.
  • 2 What is the net work if the same rectangle is traversed anticlockwise? What is the net heat?
  • 3 A cycle on the $p$–$V$ diagram is a triangle with corners $(1.0\times10^5\ \text{Pa},\ 1.0\ \text{L})$, $(3.0\times10^5\ \text{Pa},\ 1.0\ \text{L})$ and $(1.0\times10^5\ \text{Pa},\ 4.0\ \text{L})$, traversed in that order. Find the net work.
  • 4 In each cycle a gas absorbs $1200\ \text{J}$ and gives out $900\ \text{J}$ of heat. Find the net work per cycle and the power delivered at $5$ cycles per second.
  • 5 A cycle is an ellipse on the $p$–$V$ diagram with semi-axes $1.0\times10^5\ \text{Pa}$ (along $p$) and $1.0\ \text{L}$ (along $V$), traversed clockwise. Find the net work.
  • 6 A gas absorbs $500\ \text{J}$ on one leg of a cycle, gives out $300\ \text{J}$ on another and $100\ \text{J}$ on a third, with no heat on the fourth. Find $W_\text{net}$ and say whether the loop is clockwise or anticlockwise on the $p$–$V$ diagram.
  • 7 A monatomic gas goes round the rectangle $A(1.0\times10^5\ \text{Pa},\ 2.0\ \text{L})\to D(2.0\times10^5\ \text{Pa},\ 2.0\ \text{L})\to C(2.0\times10^5\ \text{Pa},\ 4.0\ \text{L})\to B(1.0\times10^5\ \text{Pa},\ 4.0\ \text{L})\to A$. Find the total heat absorbed and the net work.
  • 8 $1.0\ \text{mol}$ of a monatomic gas at $400\ \text{K}$ is taken round the cycle of Example 6 (isothermal expansion to double volume, isobaric compression, isochoric heating). Find the net work.
1 $W=\Delta p\,\Delta V=1.5\times10^5\times3.0\times10^{-3}=450\ \text{J}$.
2 $W_\text{net}=-450\ \text{J}$, and $Q_\text{net}=-450\ \text{J}$ (net heat given out).
3 Area $=\tfrac12\times2.0\times10^5\times3.0\times10^{-3}=300\ \text{J}$. The order goes up, then down-right along the slanting side, then left: clockwise, so $W=+300\ \text{J}$.
4 $W=1200-900=300\ \text{J}$ per cycle; $P=5\times300=1500\ \text{W}$.
5 $W=\pi ab=\pi\times1.0\times10^5\times1.0\times10^{-3}=314\ \text{J}$.
6 $W_\text{net}=Q_\text{net}=500-300-100=+100\ \text{J}$: positive, so clockwise.
7 $Q_{AD}=\tfrac32(400-200)=300\ \text{J}$; $Q_{DC}=\tfrac52\times200\times2.0=1000\ \text{J}$; heat absorbed $1300\ \text{J}$ ($C\to B$ and $B\to A$ give heat out). $W_\text{net}=100\times2.0=200\ \text{J}$.
8 $W_\text{net}=RT_A(\ln2-\tfrac12)=8.31\times400\times0.193=642\ \text{J}$.
IV
Harder problems.
  • 1 A gas expands from $1.0\ \text{L}$ at $4.0\times10^5\ \text{Pa}$ to $2.0\ \text{L}$ in such a way that $pV^2$ stays constant. Find the final pressure and the work done.
  • 2 A monatomic ideal gas at $27\ ^\circ\text{C}$ expands adiabatically to eight times its volume. Find its final temperature and the change in internal energy per mole.
  • 3 $1.0\ \text{mol}$ of a monatomic gas at $300\ \text{K}$ is compressed to half its volume (a) isothermally, (b) adiabatically. Find the work needed in each case ($2^{2/3}=1.587$) and explain which is larger.
  • 4 Starting from the first law and $pV=nRT$, derive $C_p-C_V=R$ for an ideal gas. Why is $C_p$ larger?
  • 5 $2.0\ \text{mol}$ of a diatomic gas absorb $1500\ \text{J}$ of heat while their temperature rises by $50\ \text{K}$. Find the work done by the gas and the molar heat capacity in this process.
  • 6 An ideal gas in an insulated vessel expands freely into a vacuum to twice its volume. A student uses $TV^{\gamma-1}=$ constant to find the final temperature. What is wrong, and what is the correct answer?
  • 7 A tyre containing air at $3.0\ \text{atm}$ (absolute) and $300\ \text{K}$ bursts suddenly. Treating the escaping air as expanding adiabatically to $1.0\ \text{atm}$, estimate its temperature ($3^{-2/7}=0.731$).
1 $p_2=p_1(V_1/V_2)^2=1.0\times10^5\ \text{Pa}$. $C=p_1V_1^2=0.40\ \text{Pa m}^6$; $W=C\left(\dfrac1{V_1}-\dfrac1{V_2}\right)=0.40\times(1000-500)=200\ \text{J}$ (equivalently $(p_1V_1-p_2V_2)/(2-1)$).
2 $T_2=300\times8^{-2/3}=300/4=75\ \text{K}$. $\Delta U=C_V\Delta T=\tfrac32\times8.31\times(-225)=-2.80\times10^3\ \text{J}$ per mole.
3 (a) $|W|=RT\ln2=8.31\times300\times0.693=1.73\times10^3\ \text{J}$. (b) $T_2=300\times2^{2/3}=476\ \text{K}$, $|W|=C_V\Delta T=\tfrac32\times8.31\times176=2.20\times10^3\ \text{J}$. More work is needed adiabatically: the gas heats up, its pressure rises faster, and the adiabat lies above the isotherm during the compression.
4 At constant $p$: $Q=nC_p\Delta T$, $\Delta U=nC_V\Delta T$ (true for any process), $W=p\Delta V=nR\Delta T$. The first law $Q=\Delta U+W$ gives $C_p=C_V+R$. $C_p$ is larger because some of the heat leaves as work of expansion.
5 $\Delta U=2.0\times\tfrac52\times8.31\times50=2078\ \text{J}$; $W=1500-2078=-578\ \text{J}$ (work is done on the gas). $C=\dfrac{Q}{n\Delta T}=\dfrac{1500}{2.0\times50}=15\ \text{J mol}^{-1}\text{K}^{-1}$ — less than $C_V$, because the work done on the gas supplies part of the rise in $U$.
6 $TV^{\gamma-1}=$ const holds only for a quasi-static adiabatic change. In a free expansion $Q=0$ and $W=0$, so $\Delta U=0$: for an ideal gas the temperature does not change at all.
7 $T_2=T_1\left(\dfrac{p_2}{p_1}\right)^{(\gamma-1)/\gamma}=300\times(1/3)^{2/7}=300\times0.731=219\ \text{K}$ (about $-54\ ^\circ\text{C}$, for an instant).
🎯 Exam corner JEE Main · MCQJEE Main · Numerical

E1. JEE Main · MCQ A monatomic ideal gas is compressed adiabatically and quasi-statically to $\tfrac18$ of its initial volume. Its pressure becomes (A) $8$ times (B) $16$ times (C) $32$ times (D) $64$ times the initial pressure

Law $pV^\gamma=$ const with $\gamma=\tfrac53$: $\dfrac{p_2}{p_1}=8^{5/3}=(8^{1/3})^5=2^5$.
Answer (C) $32$ times.
⏱ Shortcut Take the cube root first: $8^{1/3}=2$, then raise to the power $5$. (A) is the isothermal answer.

E2. JEE Main · Numerical $2$ mol of a monatomic ideal gas are heated at constant pressure from $300\ \text{K}$ to $400\ \text{K}$. Taking $R=8.3\ \text{J mol}^{-1}\text{K}^{-1}$, find the heat supplied in joules. Give the answer to the nearest integer.

Formula $Q=nC_p\Delta T$ with $C_p=\tfrac52R$ for a monatomic gas.
Numbers $Q=2\times\tfrac52\times8.3\times100=4150\ \text{J}$.
Answer $4150$.
⏱ Shortcut Using $C_V$ by mistake gives $2490$ — the work $nR\Delta T=1660\ \text{J}$ is the difference.

E3. JEE Main · MCQ Two identical samples of an ideal gas at the same initial state expand quasi-statically to the same final volume, one isothermally and the other adiabatically. Then (A) the adiabatic expansion does more work and ends at the higher pressure (B) the isothermal expansion does more work and ends at the higher pressure (C) the isothermal expansion does more work but ends at the lower pressure (D) both do the same work, since the change of volume is the same

Idea For an expansion the adiabat ($p\propto V^{-\gamma}$) falls faster than the isotherm ($p\propto V^{-1}$), so it ends lower and lies below the isotherm all the way.
Work Less area under the adiabat: the isothermal sample does more work (it absorbs heat; the adiabatic one uses up internal energy and cools).
Answer (B).
⏱ Shortcut Expansion: isotherm above adiabat. Compression: adiabat above isotherm. Draw the two curves once and read off both answers.

E4. JEE Main · Numerical An ideal gas is taken clockwise round a rectangular cycle on the $p$–$V$ diagram whose sides lie at $p=100\ \text{kPa}$ and $p=300\ \text{kPa}$ and at $V=2.0\ \text{L}$ and $V=5.0\ \text{L}$. Find the net heat absorbed by the gas per cycle, in joules. Give the answer to the nearest integer.

Cycle $\Delta U=0$, so $Q_\text{net}=W_\text{net}$ = enclosed area.
Area $(300-100)\ \text{kPa}\times(5.0-2.0)\ \text{L}=600\ \text{J}$, positive for a clockwise loop.
Answer $600$.
⏱ Shortcut No gas data needed: kPa × L is already joules. "Net heat" is the area; the heat absorbed alone would need $C_V$ and $C_p$.

E5. JEE Main · MCQ Air ($\gamma=1.4$) at $27\ ^\circ\text{C}$ is compressed adiabatically and quasi-statically to $\tfrac1{32}$ of its volume. Its final temperature is (A) $600\ \text{K}$ (B) $900\ \text{K}$ (C) $2400\ \text{K}$ (D) $1200\ \text{K}$

Law $TV^{\gamma-1}=$ const: $T_2=T_1\times32^{0.4}=300\times32^{2/5}$.
Power $32^{1/5}=2$, so $32^{2/5}=4$ and $T_2=1200\ \text{K}$.
Answer (D).
⏱ Shortcut Convert $27\ ^\circ\text{C}$ to $300\ \text{K}$ first; $27\times4=108$ is the Celsius trap. (C) uses the power $\gamma-1$ wrongly as $0.6$.

E6. JEE Main · Numerical A monatomic ideal gas is heated at constant pressure. What percentage of the heat supplied is used by the gas to do work on its surroundings? Give the answer to the nearest integer.

Ratio $\dfrac WQ=\dfrac{nR\Delta T}{nC_p\Delta T}=\dfrac{R}{\tfrac52R}=\dfrac25$.
Answer $40$.
⏱ Shortcut $W/Q=1-1/\gamma$; for $\gamma=5/3$ that is $2/5$. For a diatomic gas it would be $2/7\approx29\%$.
🔬 Research–Teaching NexusResearch-tutored · optional, about 60 minutes

Research question. What is the value of $\gamma=C_p/C_V$ for air, measured with a large bottle, a bicycle pump and a water manometer?

Why it matters. $\gamma$ controls how hot air gets when it is compressed (diesel engines, turbochargers, gas pipelines), how fast rising air cools in weather forecasting (the "adiabatic lapse rate" of about $10\ \text{K}$ per kilometre for dry air), and the speed of sound. Its value also tests kinetic theory: $1.4$ for a gas of diatomic molecules, $1.67$ for a monatomic one (Section 9.2). The method below, first used by Clément and Desormes in 1819, needs nothing more than Law 8.8.

What to do.

  1. Fit a large glass or plastic bottle (5–20 L) with a stopper carrying a tap and a tube to a U-tube water manometer.
  2. Pump in a little air, close the tap and wait several minutes for the air to return to room temperature. Read the excess pressure as a difference in water levels, $h_1$.
  3. Open the tap wide for about one second, so the pressure falls to atmospheric — fast enough to be nearly adiabatic — and close it again.
  4. Wait for the cooled air to warm back to room temperature at constant volume; read the new excess pressure $h_2$.
  5. Show that, for small pressure changes, $\gamma\approx\dfrac{h_1}{h_1-h_2}$. Repeat ten times and find the mean and its uncertainty.

Tools: Large bottle, rubber stopper with tap and tubing, bicycle or aquarium pump, U-tube with coloured water and a mm scale, stopwatch, thermometer.

Hand in: A derivation of the formula (adiabatic step: $pV^\gamma$ constant for the air that stays in the bottle; final step: isochoric), the table of $h_1$, $h_2$ and $\gamma$, your mean value with uncertainty, and a comparison with $1.40$.

Going further. Vary the time the tap is open (0.5 s, 1 s, 3 s). Why does a longer opening give a lower apparent $\gamma$? What does that tell you about how "adiabatic" a real fast process is?

Instructor note: typical student values are $1.30$–$1.38$ — low, because heat flows into the cold air while the tap is open and because the tap is closed after the pressure has overshot slightly. The trend with opening time is a good discussion of the limits of the adiabatic approximation. Keep $h_1$ below about $30\ \text{cm}$ of water so the small-change approximation holds.

🧪 Self-check quiz

0/5 correct

Q1. In an isothermal expansion of an ideal gas

Q2. The relation $pV^\gamma=$ constant applies to an ideal gas undergoing

Q3. For an ideal diatomic gas, $C_p$, $C_V$ and $\gamma$ are

Q4. A gas is taken anticlockwise round a closed loop of area $200\ \text{J}$ on a $p$–$V$ diagram. The net heat absorbed by the gas per cycle is

Q5. In an isochoric process of an ideal gas