Chapter 11 · Electrostatics

11.4 Capacitors and Dielectrics

A capacitor is two conductors that hold equal and opposite charges: $C=Q/V$, $C=\varepsilon_0A/d$ for parallel plates, $K$ times more with a dielectric between them, and it stores energy $\tfrac12CV^2$ — which we follow through series and parallel networks and through the sharing of charge.

A camera flash charges for a second or two and then releases its energy in a thousandth of a second. A defibrillator stores a few hundred joules and delivers them through a patient's chest. The touch screen of a phone senses your finger because your finger changes how much charge tiny electrodes can hold. Every one of these uses a capacitor — two conductors separated by an insulator — and every one depends on the ideas of this section: how much charge a pair of conductors holds per volt, how an insulating material between them increases that, and how much energy is stored.

We start with what happens to an insulator in an electric field (it becomes polarised, and weakens the field inside it), then define capacitance and work it out for parallel plates with and without a dielectric slab, combine capacitors in series and in parallel, and finally find the energy stored — including the surprising energy loss when two charged capacitors are joined. We use the potential and the conductor results of § 11.3 and the field of a charged plane sheet from § 11.2.

Conductors, insulators and dielectrics

In a conductor (a metal, a salt solution) some charges are free to move through the whole material. In an insulator (glass, mica, paper, plastic, dry air) every electron is bound to its own atom or molecule; it can be shifted a little, but not carried away. Put each in a uniform external field $\mathbf E_0$. In the conductor, free electrons drift until the charges induced on its surfaces produce a field that exactly cancels $\mathbf E_0$ inside — the field inside becomes zero (§ 11.3). In an insulator the charges can only shift slightly, so the induced charges cancel only part of the field. Insulators studied from this point of view are called dielectrics.

Polar and non-polar molecules. In a non-polar molecule (for example $\mathrm{O_2}$, $\mathrm{N_2}$, $\mathrm{H_2}$, $\mathrm{CO_2}$, $\mathrm{CH_4}$) the centre of the positive charges coincides with the centre of the negative charges, so the molecule has no dipole moment of its own. An external field pulls the two centres slightly apart and induces a small dipole moment along the field. A polar molecule (for example $\mathrm{H_2O}$, $\mathrm{HCl}$, $\mathrm{NH_3}$) has a permanent dipole moment, because its charge centres do not coincide. Without a field these dipoles point in random directions and their moments cancel; a field exerts a torque on each (§ 11.3, Result 11.21) and partly lines them up, against the jostling of thermal motion. Either way, the material ends up with a net dipole moment along the field.

📘 Definition 11.12 — Dielectric and electric polarisation

A dielectric is an insulating material in which an electric field produces (or lines up) molecular dipoles. The electric polarisation $\mathbf P$ of a dielectric is its net dipole moment per unit volume (unit $\text{C/m}^2$). For most materials (linear, isotropic) $\mathbf P$ is proportional to the field inside: $\mathbf P=\varepsilon_0\chi\,\mathbf E$, where the dimensionless number $\chi$ is the electric susceptibility.

Why the field is reduced. Think of a dielectric slab placed with its faces perpendicular to $\mathbf E_0$. Inside the slab the shifted positive and negative charges still balance, but on the face towards which the field points a thin layer of positive charge is left uncovered, and on the opposite face a layer of negative charge. These bound (induced) surface charges have density $\sigma_b=P$. Like two oppositely charged sheets, they make a field $\sigma_b/\varepsilon_0$ inside the slab, pointing against $\mathbf E_0$. So the field inside is $E=E_0-P/\varepsilon_0=E_0-\chi E$, which gives $E=\dfrac{E_0}{1+\chi}$.

📘 Definition 11.13 — Dielectric constant, permittivity, dielectric strength

The dielectric constant (relative permittivity) $K$ of a material is the factor by which it reduces a field:

$$K=\frac{E_0}{E}=1+\chi=\frac{\varepsilon}{\varepsilon_0},$$

where $\varepsilon=K\varepsilon_0$ is the permittivity of the material. $K=1$ for vacuum, $1.0006$ for air (taken as $1$), about $2$–$4$ for paper, plastics and oils, $5$–$10$ for glass and mica and $80$ for water; for a metal, $K\to\infty$. The dielectric strength of a material is the largest field it can withstand without breaking down (conducting): about $3\times10^6\ \text{V/m}$ for dry air and over $10^7\ \text{V/m}$ for mica.

📐 Result 11.22 — Charges in a dielectric medium

When point charges are embedded in a large uniform medium of dielectric constant $K$ (filling all the space round them), the force, field and potential are all reduced by the factor $K$:

$$F=\frac{1}{4\pi\varepsilon_0K}\frac{q_1q_2}{r^2},\qquad E=\frac{kq}{Kr^2},\qquad V=\frac{kq}{Kr}.$$

That is, replace $\varepsilon_0$ by $\varepsilon=K\varepsilon_0$. For a slab of dielectric in a uniform field $E_0$ (faces perpendicular to it): $E=E_0/K$ inside, and the bound charge density on its faces is $\sigma_b=P=\varepsilon_0(E_0-E)=\varepsilon_0E_0\left(1-\dfrac1K\right)$.

✏️ Example 1 — Forces and fields inside a dielectric
(a) Two small spheres carrying $+2.0\ \mu\text{C}$ and $+3.0\ \mu\text{C}$ are $0.30\ \text{m}$ apart in air. Find the force between them, and the force when both are immersed (same separation) in a large tank of oil of dielectric constant $4.0$. (b) A slab of glass with $K=3.0$ is placed in a uniform field of $6.0\times10^4\ \text{V/m}$, its faces perpendicular to the field. Find the field inside the glass, the polarisation and the bound surface charge density.
(a) In air $F=\dfrac{9.0\times10^9\times6.0\times10^{-12}}{0.090}=0.60\ \text{N}$ (repulsive). In the oil $F=0.60/4.0=0.15\ \text{N}$.
(b) Field $E=\dfrac{E_0}{K}=\dfrac{6.0\times10^4}{3.0}=2.0\times10^4\ \text{V/m}$.
Charges $\sigma_b=P=\varepsilon_0(E_0-E)=8.85\times10^{-12}\times4.0\times10^4=3.5\times10^{-7}\ \text{C/m}^2$.
Check $P=\varepsilon_0\chi E=\varepsilon_0(K-1)E=8.85\times10^{-12}\times2\times2.0\times10^4=3.5\times10^{-7}\ \text{C/m}^2$ ✓. The bound charge is a fraction $1-1/K=2/3$ of what a metal would need to cancel the field completely.

A slab of dielectric constant $K$ is placed in a uniform field $E_0$ with its faces perpendicular to the field. The field inside the slab is

Capacitors and the parallel-plate capacitor

Give a conductor a charge $Q$ and its potential rises in proportion: for an isolated sphere, $V=kQ/R$. The ratio $Q/V$ measures how much charge the conductor can take per volt. It is far more useful for a pair of conductors carrying equal and opposite charges, because then the field is concentrated in the space between them.

📘 Definition 11.14 — Capacitor and capacitance

A capacitor is a system of two conductors (the plates), insulated from each other, carrying charges $+Q$ and $-Q$. If $V$ is the potential difference between them, the capacitance is

$$C=\frac{Q}{V}.$$

Its SI unit is the farad: $1\ \text{F}=1\ \text{C/V}$ (practical sizes are $\mu\text{F}$, $\text{nF}$, $\text{pF}$). $C$ depends only on the size, shape and separation of the conductors and on the medium between them — not on $Q$ or $V$. The symbol is two parallel lines ⊣⊢. For a single isolated conductor, $C=Q/V$ with $V$ measured from infinity; an isolated sphere of radius $R$ has $C=4\pi\varepsilon_0R=R/k$.

Even the whole Earth, with $R=6.4\times10^6\ \text{m}$, has only $C=R/k=7.1\times10^{-4}\ \text{F}=711\ \mu\text{F}$ as an isolated sphere — the farad is a very large unit. Two plates close together do much better.

The parallel-plate capacitor. Take two flat metal plates of area $A$, a distance $d$ apart, with $d$ much smaller than the size of the plates. Charges $+Q$ and $-Q$ spread uniformly over their inner faces with densities $\pm\sigma$, $\sigma=Q/A$. Each sheet makes a field $\sigma/2\varepsilon_0$ (§ 11.2). Between the plates the two fields point the same way and add; outside they cancel:

$$E=\frac{\sigma}{\varepsilon_0}=\frac{Q}{\varepsilon_0A}\ \text{(between)},\qquad E=0\ \text{(outside)}.$$

The field is uniform, so $V=Ed=\dfrac{Qd}{\varepsilon_0A}$, and $C=Q/V$:

📐 Result 11.23 — Parallel-plate capacitor

For two parallel plates of area $A$ a distance $d$ apart in vacuum (or air), with $d$ small compared with the plate size so that the field is uniform between them and the bending of field lines at the edges ("fringing") can be ignored:

$$C_0=\frac{\varepsilon_0A}{d},\qquad E=\frac{\sigma}{\varepsilon_0}=\frac{V}{d}.$$

$C$ grows with the area and falls as the plates move apart.

With a dielectric. Fill the whole gap with a dielectric of constant $K$, keeping the charge $Q$ fixed. The field between the plates drops to $E_0/K$, so $V$ drops to $V_0/K$ and the capacitance rises to $KC_0$ — this is in fact the best way to measure $K$. Now suppose the slab has thickness $t\lt d$ and the same area as the plates. With free charge density $\sigma$ on the plates, the field is $\sigma/\varepsilon_0$ in the air gaps (total thickness $d-t$) and $\sigma/K\varepsilon_0$ in the slab. Adding the potential drops,

$$V=\frac{\sigma}{\varepsilon_0}(d-t)+\frac{\sigma}{K\varepsilon_0}t=\frac{Q}{\varepsilon_0A}\left(d-t+\frac tK\right).$$
📐 Result 11.24 — Parallel-plate capacitor with a dielectric or a metal slab

For plates of area $A$ and separation $d$:

  • gap completely filled with a dielectric of constant $K$: $\ C=\dfrac{K\varepsilon_0A}{d}=KC_0$;
  • a dielectric slab of thickness $t$ (covering the full area, parallel to the plates): $\ C=\dfrac{\varepsilon_0A}{d-t+t/K}$;
  • a metal slab of thickness $t$ (the limit $K\to\infty$): $\ C=\dfrac{\varepsilon_0A}{d-t}$.

The answer does not depend on where the slab sits between the plates. Each slab acts as if it shortened the gap: a dielectric by $t(1-1/K)$, a metal by its whole thickness $t$.

✏️ Example 2 — Sizing a parallel-plate capacitor
A parallel-plate capacitor in air has square plates $10\ \text{cm}$ on a side, $1.0\ \text{mm}$ apart. (a) Find its capacitance. It is connected to a $100\ \text{V}$ supply. Find (b) the charge on each plate, (c) the field between the plates and (d) the surface charge density, checking that $E=\sigma/\varepsilon_0$. (e) What plate area would give $1.0\ \text{F}$ with the same gap?
(a) $A=0.010\ \text{m}^2$: $C=\dfrac{8.85\times10^{-12}\times0.010}{1.0\times10^{-3}}=8.85\times10^{-11}\ \text{F}=88.5\ \text{pF}$.
(b), (c) $Q=CV=8.85\times10^{-9}\ \text{C}=8.85\ \text{nC}$; $\ E=\dfrac{V}{d}=\dfrac{100}{1.0\times10^{-3}}=1.0\times10^5\ \text{V/m}$.
(d) $\sigma=\dfrac{Q}{A}=8.85\times10^{-7}\ \text{C/m}^2$, and $\dfrac{\sigma}{\varepsilon_0}=1.0\times10^5\ \text{V/m}$ ✓.
(e) $A=\dfrac{Cd}{\varepsilon_0}=\dfrac{1.0\times1.0\times10^{-3}}{8.85\times10^{-12}}=1.1\times10^8\ \text{m}^2$ — a square more than $10\ \text{km}$ on a side. Large capacitors use thin dielectrics, high $K$ and rolled-up foils instead.
✏️ Example 3 — A slab that half fills the gap, and a metal one
A parallel-plate capacitor has plates of area $200\ \text{cm}^2$, $6.0\ \text{mm}$ apart. (a) Find its capacitance in air. (b) A slab of dielectric constant $4.0$ and thickness $4.0\ \text{mm}$, the same area as the plates, is placed between them. Find the new capacitance. (c) What would it be with a metal slab of the same thickness instead? (d) With the dielectric slab in place, the capacitor is connected to $30\ \text{V}$. Find the fields in the air and in the slab, and check that they account for the $30\ \text{V}$.
Find the capacitance in (b) before you open the solution:
(a) $\varepsilon_0A=8.85\times10^{-12}\times0.020=1.77\times10^{-13}\ \text{F m}$; $C_0=\dfrac{1.77\times10^{-13}}{6.0\times10^{-3}}=29.5\ \text{pF}$.
(b) $d-t+t/K=2.0+1.0=3.0\ \text{mm}$: $C=\dfrac{1.77\times10^{-13}}{3.0\times10^{-3}}=59.0\ \text{pF}$ — double $C_0$.
(c) Metal: $C=\dfrac{\varepsilon_0A}{d-t}=\dfrac{1.77\times10^{-13}}{2.0\times10^{-3}}=88.5\ \text{pF}$.
(d) $Q=CV=59.0\times10^{-12}\times30=1.77\times10^{-9}\ \text{C}$, $\sigma=Q/A=8.85\times10^{-8}\ \text{C/m}^2$. Air: $E=\sigma/\varepsilon_0=1.0\times10^4\ \text{V/m}$; slab: $E/K=2.5\times10^3\ \text{V/m}$.
Check $1.0\times10^4\times0.0020+2.5\times10^3\times0.0040=20+10=30\ \text{V}$ ✓ — two-thirds of the voltage is across the thin air gap.

In Interactive 1 choose charged to 12 V, then isolated, and set $d=2.0\ \text{mm}$, $t=1.0\ \text{mm}$, $K=4$. When the slab is fully in, what is the voltage across the plates?

With the slab fully in, the readouts show $C=70.8\ \text{pF}$ (up from $44.3\ \text{pF}$), $Q=531\ \text{pC}$ (unchanged — the plates are isolated), $V=Q/C=7.50\ \text{V}$ and $U=1.99\ \text{nJ}$ (down from $3.19\ \text{nJ}$). $C$ rises by $d/(d-t+t/K)=2.0/1.25=1.6$, so $V$ falls by $1.6$. $3.0\ \text{V}$ would be $12/K$, true only if the slab filled the whole gap. Switch to battery connected: now $V$ stays $12\ \text{V}$, $Q$ rises to $850\ \text{pC}$ and $U$ rises to $5.1\ \text{nJ}$.
Interactive 1 — Sliding a Slab into a Capacitor

A parallel-plate capacitor (plate area $100\ \text{cm}^2$) is first charged to $12\ \text{V}$. Choose whether the battery stays connected or is removed, set the gap $d$, the slab thickness $t$ and its dielectric constant $K$, then press Play to slide the slab in. The graph shows $C$ and the stored energy $U$, as multiples of their starting values, against the fraction of the slab inside. (A slab with $t=d$ fills the gap.)

2.0 mm2.0 mm3.0
capacitance $C$—
charge $Q$—
voltage $V$—
energy $U$—

An air-filled parallel-plate capacitor is charged and then disconnected from the battery. Its plates are pulled apart until the gap is doubled. The potential difference between the plates

Combinations of capacitors

Capacitors are connected together to obtain a value not available on its own, or to share a high voltage between several capacitors so that none breaks down. Two basic ways of connecting them lead to simple rules. In each case the equivalent capacitance is the single capacitor that would store the same charge when connected across the same total voltage.

In parallel, one plate of each capacitor is joined to one terminal and the other plates to the other terminal, so all have the same potential difference $V$. The charges $Q_i=C_iV$ add: $Q=(C_1+C_2+\cdots)V$. In series, the capacitors are joined end to end. A charge $+Q$ put on the first plate induces $-Q$ on the facing plate; the isolated piece of conductor between two capacitors has zero net charge, so $+Q$ appears on the next plate, and so on. All carry the same charge $Q$, and the voltages $V_i=Q/C_i$ add: $V=Q\left(\dfrac1{C_1}+\dfrac1{C_2}+\cdots\right)$.

📐 Result 11.25 — Capacitors in series and in parallel

Parallel (same $V$, charges add, $Q_i\propto C_i$): $\qquad C=C_1+C_2+\cdots+C_n$.

Series (same $Q$, voltages add, $V_i\propto1/C_i$): $\qquad\dfrac1C=\dfrac1{C_1}+\dfrac1{C_2}+\cdots+\dfrac1{C_n}$.

For two in series, $C=\dfrac{C_1C_2}{C_1+C_2}$ and the supply voltage divides as $V_1=\dfrac{C_2}{C_1+C_2}V$, $V_2=\dfrac{C_1}{C_1+C_2}V$ — the smaller capacitor takes the larger share. A series combination is smaller than its smallest member; a parallel one is larger than its largest. $n$ equal capacitors $C$: $nC$ in parallel, $C/n$ in series.

Dielectric arrangements are combinations. If two dielectrics fill the gap side by side (each covering part of the plate area, each the full thickness), both parts have the same voltage: they are in parallel, $C=\dfrac{\varepsilon_0}{d}(K_1A_1+K_2A_2)$. If they are stacked in layers (each covering the whole area, thicknesses $t_1+t_2=d$), the same charge passes through both: they are in series, $\dfrac1C=\dfrac{1}{\varepsilon_0A}\left(\dfrac{t_1}{K_1}+\dfrac{t_2}{K_2}\right)$. The partial slab of Result 11.24 is just a layer of dielectric in series with a layer of air.

🧭 Problem-solving strategy — Capacitor networks
  1. Find groups that are clearly in parallel (both ends joined to the same two points) or in series (joined end to end with nothing else connected at the junction). Replace each group by its equivalent, and repeat.
  2. For the whole network, $Q_\text{total}=C_\text{eq}V$.
  3. Work back out: capacitors in series with the battery carry $Q_\text{total}$; across a parallel group, find the common voltage and then each charge $Q_i=C_iV_i$.
  4. Check: the voltages round any loop add up to the supply voltage, and the charges arriving at any junction balance.
  5. A bridge of five capacitors with $C_1/C_2=C_3/C_4$ is balanced: the middle capacitor carries no charge and can be removed.
✏️ Example 4 — Working through a network
Capacitors of $3.0\ \mu\text{F}$ and $6.0\ \mu\text{F}$ are joined in series. This pair is connected in parallel with a $4.0\ \mu\text{F}$ capacitor, and the whole group is in series with a $12\ \mu\text{F}$ capacitor across an $18\ \text{V}$ battery. Find (a) the equivalent capacitance, (b) the charge drawn from the battery, and (c) the charge on and voltage across each capacitor.
(a) $3$ and $6$ in series: $\dfrac{3\times6}{9}=2.0\ \mu\text{F}$. In parallel with $4$: $6.0\ \mu\text{F}$. In series with $12$: $\dfrac{6\times12}{18}=4.0\ \mu\text{F}$.
(b) $Q=C_\text{eq}V=4.0\times18=72\ \mu\text{C}$.
(c) $12\ \mu\text{F}$: carries $72\ \mu\text{C}$, $V=72/12=6.0\ \text{V}$. The parallel group has $18-6=12\ \text{V}$: the $4\ \mu\text{F}$ holds $48\ \mu\text{C}$; the series pair ($2\ \mu\text{F}$) holds $24\ \mu\text{C}$, so the $3\ \mu\text{F}$ has $8.0\ \text{V}$ and the $6\ \mu\text{F}$ has $4.0\ \text{V}$, each with $24\ \mu\text{C}$.
Check Charges: $48+24=72\ \mu\text{C}$ ✓. Loop through the pair: $8+4+6=18\ \text{V}$ ✓; through the $4\ \mu\text{F}$: $12+6=18\ \text{V}$ ✓.
✏️ Example 5 — Two dielectrics: side by side and in layers
An air capacitor has plates of area $100\ \text{cm}^2$, $2.0\ \text{mm}$ apart. (a) Find $C_0$. Find the capacitance when the gap is filled (b) by two slabs side by side, each covering half the area and the full thickness, with $K_1=2.0$ and $K_2=6.0$; (c) by the same two materials as layers, each $1.0\ \text{mm}$ thick and covering the whole area.
Find the capacitance in (c), with the layers:
(a) $C_0=\dfrac{8.85\times10^{-12}\times0.010}{2.0\times10^{-3}}=44.3\ \text{pF}$.
(b) Side by side = parallel, each half: $\dfrac{K_1C_0}{2}+\dfrac{K_2C_0}{2}=\dfrac{2+6}{2}C_0=4C_0=177\ \text{pF}$.
(c) Layers = series of $2K_1C_0=4C_0$ and $2K_2C_0=12C_0$: $C=\dfrac{4\times12}{16}C_0=3C_0=133\ \text{pF}$.
⏱ Shortcut Side by side: $C_0\times$ (area-weighted average of $K$). Layers, equal thicknesses: $C_0\times\dfrac{2K_1K_2}{K_1+K_2}$ (the harmonic mean). The harmonic mean is never larger, so layers always give the smaller answer.

You have three $2\ \mu\text{F}$ capacitors and must use all three. Which of these equivalent capacitances can you not make?

Energy stored and sharing of charge

Charging a capacitor means moving charge from one plate to the other against the growing voltage between them. Suppose at some moment the plates hold $\pm q$, so the voltage is $q/C$. Moving a further $dq$ needs work $dW=\dfrac{q}{C}\,dq$. Charging from $0$ to $Q$:

$$W=\int_0^Q\frac qC\,dq=\frac{Q^2}{2C}.$$

This work is stored as electric potential energy, and it can be recovered when the capacitor discharges.

📐 Result 11.26 — Energy stored in a capacitor; energy density

A capacitor of capacitance $C$ with charge $Q$ and voltage $V$ stores energy

$$U=\frac{Q^2}{2C}=\frac12CV^2=\frac12QV.$$

For a parallel-plate capacitor, $U=\tfrac12(\varepsilon_0A/d)(Ed)^2=\tfrac12\varepsilon_0E^2\times(Ad)$, so the energy can be thought of as stored in the field, with energy density (energy per unit volume) $u=\tfrac12\varepsilon_0E^2$ — or $\tfrac12K\varepsilon_0E^2$ in a dielectric. The plates attract each other with force $F=\dfrac{Q^2}{2\varepsilon_0A}=\tfrac12QE$ (each plate feels the field $\sigma/2\varepsilon_0$ of the other only).

A battery of emf $V$ that charges an uncharged capacitor to $V$ supplies energy $QV=CV^2$; only half, $\tfrac12CV^2$, is stored. The other half is lost as heat in the connecting resistance (and radiation), however small the resistance.

Inserting a dielectric — two different situations. What happens to $Q$, $V$, $E$ and $U$ when a slab of constant $K$ is pushed in to fill the gap depends on whether the battery is still connected.

📐 Result 11.27 — Effect of filling the gap with a dielectric
quantitybattery connected ($V$ fixed)isolated ($Q$ fixed)
capacitance$KC_0$$KC_0$
charge$KQ_0$$Q_0$
voltage$V_0$$V_0/K$
field between plates$E_0$$E_0/K$
energy stored$KU_0$$U_0/K$

In both cases the slab is pulled in by the field. With the plates isolated, the energy that disappears, $U_0(1-1/K)$, is the work done on the slab. With the battery connected, the battery supplies $(K-1)Q_0V_0$: half goes into the extra stored energy and half into work on the slab.

Sharing of charge. Take a capacitor $C_1$ charged to $V_1$ and a capacitor $C_2$ charged to $V_2$, and join them — positive plate to positive plate, negative to negative. Charge flows until the two voltages are equal. No charge can leave the joined pair of upper plates, so the total charge on them is conserved: $C_1V_1+C_2V_2=(C_1+C_2)V$.

📐 Result 11.28 — Sharing of charge between two capacitors

When $C_1$ (at $V_1$) and $C_2$ (at $V_2$) are joined with like plates together, the common potential and the energy lost are

$$V=\frac{C_1V_1+C_2V_2}{C_1+C_2},\qquad\Delta U=U_\text{before}-U_\text{after}=\frac{C_1C_2\,(V_1-V_2)^2}{2(C_1+C_2)}.$$

If they are joined with opposite plates together, replace $V_2$ by $-V_2$: $V=\dfrac{C_1V_1-C_2V_2}{C_1+C_2}$ and $\Delta U=\dfrac{C_1C_2(V_1+V_2)^2}{2(C_1+C_2)}$. Charge is conserved, but energy is always lost (unless $V_1=V_2$): it becomes heat in the connecting wires and electromagnetic radiation. When $C_2$ is uncharged, the fraction lost is $\dfrac{C_2}{C_1+C_2}$.

✏️ Example 6 — Joining two charged capacitors
A $4.0\ \mu\text{F}$ capacitor charged to $50\ \text{V}$ and a $2.0\ \mu\text{F}$ capacitor charged to $20\ \text{V}$ are disconnected from their supplies. (a) They are joined positive plate to positive plate. Find the common voltage, the final charges, and the energy before and after; check the loss against Result 11.28. (b) Repeat with the positive plate of each joined to the negative plate of the other.
Find the energy lost in (a):
(a) $V=\dfrac{4.0\times50+2.0\times20}{6.0}=\dfrac{240}{6.0}=40\ \text{V}$. Final charges $160\ \mu\text{C}$ and $80\ \mu\text{C}$ (total $240\ \mu\text{C}$, as before).
Energy Before: $\tfrac12(4.0)(50)^2+\tfrac12(2.0)(20)^2=5000+400=5400\ \mu\text{J}$. After: $\tfrac12(6.0)(40)^2=4800\ \mu\text{J}$. Lost: $600\ \mu\text{J}$; formula: $\dfrac{4.0\times2.0\times30^2}{2\times6.0}=600\ \mu\text{J}$ ✓.
(b) Net charge on the joined plates $200-40=160\ \mu\text{C}$: $V=\dfrac{160}{6.0}=26.7\ \text{V}$. After: $\tfrac12(6.0)(26.7)^2=2130\ \mu\text{J}$, so $3270\ \mu\text{J}$ is lost; formula $\dfrac{8.0\times70^2}{12}=3270\ \mu\text{J}$ ✓.
⏱ Shortcut Charge is conserved, energy is not. The loss is like a perfectly inelastic collision: $\Delta U=\tfrac12C_\text{s}(\Delta V)^2$ with $C_\text{s}=C_1C_2/(C_1+C_2)$ the series combination and $\Delta V$ the initial voltage difference.

In Interactive 2 set $C_1=3\ \mu\text{F}$ at $V_1=40\ \text{V}$ and $C_2=1\ \mu\text{F}$ uncharged ($V_2=0$), like plates together. What fraction of the stored energy is lost when the switch is closed?

The readouts show a common voltage of $30\ \text{V}$, final charges $90$ and $30\ \mu\text{C}$ and an energy loss of $600\ \mu\text{J}$ (25%) — a quarter of the $2400\ \mu\text{J}$ stored at first. With $C_2$ uncharged the fraction lost is $C_2/(C_1+C_2)=1/4$. $50\,\%$ is the loss when a battery charges a capacitor, or when two equal capacitors share. Try $C_2=3\ \mu\text{F}$: the loss becomes $50\,\%$.
Interactive 2 — Sharing Charge Between Two Capacitors

Two charged capacitors are joined through a switch and a small resistance. Set their capacitances and starting voltages and how they are joined, then press Play to close the switch. The graph shows both voltages (in the same sense round the circuit) settling to a common value, and the bar shows the stored energy falling — charge is conserved, energy is not.

4 μF50 V2 μF20 V
common voltage—
final $Q_1$—
final $Q_2$—
energy lost—
⚠️ JEE Main traps

1. Battery connected or not? Read the question twice. Connected: $V$ is fixed, so $Q$, $E$-energy follow $C$. Disconnected (isolated): $Q$ is fixed, so $V=Q/C$ and $U=Q^2/2C$ fall when $C$ rises. Most wrong answers on dielectric insertion or moving plates come from mixing these.

2. Series and parallel the wrong way round. Capacitors in parallel add (like resistors in series); in series their reciprocals add. Series capacitors share the same charge, not the same voltage.

3. A partial slab is not $KC_0$. A slab of thickness $t\lt d$ gives $\varepsilon_0A/(d-t+t/K)$; a metal slab $\varepsilon_0A/(d-t)$; side-by-side dielectrics add in parallel, layers in series.

4. Energy is not conserved when charge is shared. The common voltage comes from charge conservation; the energy afterwards is always less. And a battery charging a capacitor loses half its energy as heat.

5. Units. $\mu\text{F}\times\text{V}=\mu\text{C}$ and $\mu\text{F}\times\text{V}^2=\mu\text{J}$; areas in $\text{m}^2$ ($100\ \text{cm}^2=0.010\ \text{m}^2$), gaps in $\text{m}$. Picofarads are typical for parallel plates of laboratory size.

A parallel-plate capacitor stays connected to a battery while its plate separation is doubled. The energy stored in it

Exercises

Take $\varepsilon_0=8.85\times10^{-12}\ \text{C}^2\text{N}^{-1}\text{m}^{-2}$ and $k=9.0\times10^9\ \text{N m}^2\text{C}^{-2}$; the medium is air ($K=1$) unless stated.

I
Dielectrics and the parallel-plate capacitor.
  • 1 A capacitor holds $60\ \mu\text{C}$ when connected across $12\ \text{V}$. Find its capacitance.
  • 2 Find the capacitance of two circular plates of radius $6.0\ \text{cm}$, $2.0\ \text{mm}$ apart.
  • 3 Find the capacitance of an isolated metal sphere of radius $9.0\ \text{cm}$.
  • 4 What plate separation gives $1.0\ \text{nF}$ with plates of area $0.050\ \text{m}^2$?
  • 5 Air breaks down at $3.0\times10^6\ \text{V/m}$. Find the largest voltage and the largest charge for the capacitor of part 2.
  • 6 A slab with $K=5.0$ is placed in a uniform field of $1.0\times10^5\ \text{V/m}$, faces perpendicular to the field. Find the field inside and the bound surface charge density.
  • 7 Give two examples each of polar and non-polar molecules, and describe how each kind responds to an applied field.
  • 8 Two charges repel with $0.80\ \text{N}$ in air and with $0.32\ \text{N}$ when immersed, at the same separation, in a large volume of oil. Find the dielectric constant of the oil.
1 $C=\dfrac{Q}{V}=\dfrac{60}{12}=5.0\ \mu\text{F}$.
2 $A=\pi(0.060)^2=0.0113\ \text{m}^2$; $C=\dfrac{8.85\times10^{-12}\times0.0113}{2.0\times10^{-3}}=5.0\times10^{-11}\ \text{F}=50.0\ \text{pF}$.
3 $C=\dfrac{R}{k}=\dfrac{0.090}{9.0\times10^9}=1.0\times10^{-11}\ \text{F}=10\ \text{pF}$.
4 $d=\dfrac{\varepsilon_0A}{C}=\dfrac{8.85\times10^{-12}\times0.050}{1.0\times10^{-9}}=4.43\times10^{-4}\ \text{m}=0.443\ \text{mm}$.
5 $V_\text{max}=E_\text{max}d=3.0\times10^6\times2.0\times10^{-3}=6.0\times10^3\ \text{V}$; $Q_\text{max}=CV_\text{max}=50\times10^{-12}\times6000=3.0\times10^{-7}\ \text{C}$.
6 $E=E_0/K=2.0\times10^4\ \text{V/m}$; $\sigma_b=\varepsilon_0(E_0-E)=8.85\times10^{-12}\times8.0\times10^4=7.08\times10^{-7}\ \text{C/m}^2$.
7 Polar: $\mathrm{H_2O}$, $\mathrm{HCl}$ (permanent dipoles, randomly oriented; the field partly aligns them against thermal motion). Non-polar: $\mathrm{O_2}$, $\mathrm{CH_4}$ (no dipole of their own; the field separates the charge centres and induces a dipole along it). Both give a net polarisation along the field.
8 $F\propto1/K$: $K=\dfrac{0.80}{0.32}=2.5$.
II
Capacitors with dielectric and metal slabs. A parallel-plate capacitor has plates of area $100\ \text{cm}^2$ and gap $3.0\ \text{mm}$.
  • 1 Find its capacitance in air.
  • 2 Find its capacitance when the gap is completely filled with a material of $K=6.0$.
  • 3 Find its capacitance with a slab of $K=6.0$ and thickness $1.5\ \text{mm}$ (full area) in the gap.
  • 4 Find its capacitance with a metal slab $1.5\ \text{mm}$ thick (full area) in the gap.
  • 5 Explain why, in parts 3 and 4, it does not matter whether the slab touches one plate or sits in the middle.
  • 6 A slab $2.0\ \text{mm}$ thick raises the capacitance to $1.5$ times its air value. Find its dielectric constant.
  • 7 Find the capacitance when half of the plate area is filled across the full gap with a material of $K=5.0$, the other half being air.
  • 8 In the arrangement of part 3 the capacitor is connected to $100\ \text{V}$. Find the field in the air gap and in the slab.
1 $C_0=\dfrac{8.85\times10^{-12}\times0.010}{3.0\times10^{-3}}=2.95\times10^{-11}\ \text{F}=29.5\ \text{pF}$.
2 $C=KC_0=6.0\times29.5=177\ \text{pF}$.
3 $d-t+t/K=1.5+0.25=1.75\ \text{mm}$: $C=\dfrac{8.85\times10^{-14}}{1.75\times10^{-3}}=50.6\ \text{pF}$.
4 $C=\dfrac{8.85\times10^{-14}}{1.5\times10^{-3}}=59.0\ \text{pF}$.
5 The potential drop is $E_\text{air}\times(\text{total air thickness})+E_\text{slab}\times t$; moving the slab only redistributes the air between the two sides, leaving the total air thickness $d-t$ unchanged.
6 $3.0-2.0+\dfrac{2.0}{K}=\dfrac{3.0}{1.5}=2.0$, so $\dfrac{2.0}{K}=1.0$ and $K=2.0$.
7 Parallel halves: $C=\dfrac{C_0}{2}(1+5.0)=3C_0=88.5\ \text{pF}$.
8 $Q=50.6\times10^{-12}\times100=5.06\times10^{-9}\ \text{C}$, $\sigma=5.06\times10^{-7}\ \text{C/m}^2$. $E_\text{air}=\sigma/\varepsilon_0=5.71\times10^4\ \text{V/m}$; $E_\text{slab}=E_\text{air}/6=9.5\times10^3\ \text{V/m}$. Check: $85.7+14.3=100\ \text{V}$ ✓.
III
Series and parallel combinations.
  • 1 Find the equivalent capacitance of $2.0$, $3.0$ and $6.0\ \mu\text{F}$ in series.
  • 2 Find the equivalent capacitance of the same three in parallel.
  • 3 The series combination of part 1 is connected across $12\ \text{V}$. Find the charge on each capacitor and the voltage across the $2.0\ \mu\text{F}$ one.
  • 4 Capacitors of $4\ \mu\text{F}$ can each safely take $100\ \text{V}$. What is the least number needed to make a combination of $4\ \mu\text{F}$ that can take $300\ \text{V}$?
  • 5 A $4.0\ \mu\text{F}$ and a $12\ \mu\text{F}$ capacitor in series are connected in parallel with a $2.0\ \mu\text{F}$ capacitor across $20\ \text{V}$. Find the charge on the $12\ \mu\text{F}$ capacitor.
  • 6 In a bridge, $C_1=2.0$ and $C_2=4.0\ \mu\text{F}$ are in series on one branch, $C_3=3.0$ and $C_4=6.0\ \mu\text{F}$ in series on the other, and a $5.0\ \mu\text{F}$ capacitor joins the two junctions. Find the equivalent capacitance between the ends.
  • 7 Two capacitors have an equivalent capacitance of $9.0\ \mu\text{F}$ in parallel and $2.0\ \mu\text{F}$ in series. Find them.
  • 8 Explain why capacitors in series carry equal charges even when their capacitances differ.
1 $\dfrac1C=\dfrac12+\dfrac13+\dfrac16=1$: $C=1.0\ \mu\text{F}$.
2 $C=2+3+6=11\ \mu\text{F}$.
3 $Q=1.0\times12=12\ \mu\text{C}$ on each; $V_{2\,\mu\text{F}}=12/2.0=6.0\ \text{V}$ (and $4.0$, $2.0\ \text{V}$ on the others).
4 Three in series share $300\ \text{V}$ ($100\ \text{V}$ each) but give $\tfrac43\ \mu\text{F}$; three such rows in parallel give $4\ \mu\text{F}$. Total $9$.
5 The series pair is $\dfrac{4\times12}{16}=3.0\ \mu\text{F}$, across the full $20\ \text{V}$: it holds $60\ \mu\text{C}$, and so does each of its members.
6 Balanced ($2/4=3/6$): the junctions are at the same potential and the $5\ \mu\text{F}$ capacitor is uncharged. $C=\dfrac{2\times4}{6}+\dfrac{3\times6}{9}=1.33+2.00=3.33\ \mu\text{F}$.
7 $C_1+C_2=9$, $C_1C_2=2\times9=18$: the roots of $x^2-9x+18=0$, i.e. $3.0\ \mu\text{F}$ and $6.0\ \mu\text{F}$.
8 The plates joined between two series capacitors form an isolated conductor that started neutral. Charge only moves within it, so the $-Q$ on one plate is matched by $+Q$ on the other: every capacitor in the chain carries the same $Q$.
IV
Energy and sharing of charge.
  • 1 Find the energy stored in a $50\ \mu\text{F}$ capacitor charged to $200\ \text{V}$.
  • 2 Find the energy density in air where the field is $2.0\times10^5\ \text{V/m}$.
  • 3 An $8.0\ \mu\text{F}$ capacitor is charged to $100\ \text{V}$ and disconnected. A slab with $K=4.0$ is pushed in to fill the gap. Find the new voltage and the new stored energy (in mJ).
  • 4 Repeat part 3 with the battery left connected. Find the new stored energy and the energy supplied by the battery during the insertion.
  • 5 A $6.0\ \mu\text{F}$ capacitor charged to $120\ \text{V}$ is connected to an uncharged $3.0\ \mu\text{F}$ capacitor. Find the common voltage and the energy lost.
  • 6 A $12\ \text{V}$ battery charges an uncharged $5.0\ \mu\text{F}$ capacitor through a resistor. Find the energy supplied by the battery and the heat produced.
  • 7 The plates of an isolated capacitor of area $0.010\ \text{m}^2$ carry $\pm0.20\ \mu\text{C}$. Find the force of attraction between them.
  • 8 Capacitors of $2.0\ \mu\text{F}$ at $100\ \text{V}$ and $3.0\ \mu\text{F}$ at $50\ \text{V}$ are joined with opposite plates together. Find the common voltage and the energy lost.
1 $U=\tfrac12CV^2=\tfrac12\times50\times10^{-6}\times(200)^2=1.0\ \text{J}$.
2 $u=\tfrac12\varepsilon_0E^2=\tfrac12\times8.85\times10^{-12}\times4.0\times10^{10}=0.177\ \text{J/m}^3$.
3 $Q=800\ \mu\text{C}$ fixed, $C=32\ \mu\text{F}$: $V=25\ \text{V}$; $U=\tfrac12QV=\tfrac12\times800\times10^{-6}\times25=10\ \text{mJ}$ (down from $40\ \text{mJ}$: $30\ \text{mJ}$ of work was done on the slab as it was pulled in).
4 $V=100\ \text{V}$, $C=32\ \mu\text{F}$: $U=\tfrac12\times32\times10^{-6}\times10^4=160\ \text{mJ}$. Charge rises from $800$ to $3200\ \mu\text{C}$; the battery supplies $\Delta Q\,V=2400\times10^{-6}\times100=240\ \text{mJ}$ — $120\ \text{mJ}$ extra stored and $120\ \text{mJ}$ as work on the slab.
5 $V=\dfrac{6.0\times120}{9.0}=80\ \text{V}$; $\Delta U=\dfrac{6.0\times3.0\times120^2}{2\times9.0}=1.44\times10^4\ \mu\text{J}=14.4\ \text{mJ}$ (one third of the original $43.2\ \text{mJ}$).
6 $Q=60\ \mu\text{C}$; battery supplies $QV=720\ \mu\text{J}$; stored $\tfrac12QV=360\ \mu\text{J}$; heat $360\ \mu\text{J}$.
7 $F=\dfrac{Q^2}{2\varepsilon_0A}=\dfrac{(2.0\times10^{-7})^2}{2\times8.85\times10^{-12}\times0.010}=0.226\ \text{N}$.
8 Net charge $200-150=50\ \mu\text{C}$ on $5.0\ \mu\text{F}$: $V=10\ \text{V}$. $\Delta U=\dfrac{2.0\times3.0\times(100+50)^2}{2\times5.0}=1.35\times10^4\ \mu\text{J}=13.5\ \text{mJ}$.
🎯 Exam corner JEE Main · MCQJEE Main · Numerical

E1. JEE Main · MCQ An air-filled parallel-plate capacitor has capacitance $C$. A slab of dielectric constant $3$, of thickness half the plate separation and the same area as the plates, is placed between the plates. The new capacitance is (A) $3C/2$ (B) $2C$ (C) $3C$ (D) $4C/3$

Formula $C'=\dfrac{\varepsilon_0A}{d-t+t/K}=\dfrac{\varepsilon_0A}{d/2+d/6}=\dfrac{\varepsilon_0A}{2d/3}$.
Ratio $C'=\tfrac32\,\dfrac{\varepsilon_0A}{d}=\tfrac32C$.
Answer (A).
⏱ Shortcut Layers in series: $2C$ (air half) and $2KC=6C$ (slab half) give $\dfrac{2\times6}{8}C=\tfrac32C$. (C) assumes the slab fills the gap.

E2. JEE Main · Numerical Capacitors of $2\ \mu\text{F}$ and $3\ \mu\text{F}$ are connected in series across a $50\ \text{V}$ supply. Find the energy stored in the $2\ \mu\text{F}$ capacitor, in microjoules. Give the answer to the nearest integer.

Charge $C_\text{eq}=\dfrac{2\times3}{5}=1.2\ \mu\text{F}$; $Q=1.2\times50=60\ \mu\text{C}$ on each.
Energy $U=\dfrac{Q^2}{2C}=\dfrac{60^2}{2\times2}=900\ \mu\text{J}$ (it has $30\ \text{V}$ across it).
Answer $900$.
⏱ Shortcut The smaller capacitor in series takes the larger voltage, $\tfrac35\times50=30\ \text{V}$: $U=\tfrac12\times2\times30^2=900\ \mu\text{J}$.

E3. JEE Main · MCQ A parallel-plate capacitor is charged by a battery, the battery is removed, and then a dielectric slab of constant $K$ is inserted to fill the gap. Which statement is correct? (A) The charge on the plates increases $K$ times (B) The potential difference and the stored energy both decrease $K$ times (C) The field between the plates is unchanged (D) The stored energy increases $K$ times

Fixed Isolated plates: $Q$ is constant while $C\to KC$.
Changes $V=Q/C\to V/K$, $E=V/d\to E/K$, $U=Q^2/2C\to U/K$.
Answer (B).
⏱ Shortcut (A) and (D) describe the battery-connected case; (C) is also true only with the battery connected.

E4. JEE Main · Numerical A $10\ \mu\text{F}$ capacitor charged to $60\ \text{V}$ is connected across an uncharged $20\ \mu\text{F}$ capacitor. Find the heat produced in the connecting wires, in millijoules. Give the answer to the nearest integer.

Common V $V=\dfrac{10\times60}{30}=20\ \text{V}$.
Energies Before $\tfrac12\times10\times60^2=18\,000\ \mu\text{J}$; after $\tfrac12\times30\times20^2=6000\ \mu\text{J}$; heat $12\,000\ \mu\text{J}=12\ \text{mJ}$.
Answer $12$.
⏱ Shortcut $\Delta U=\dfrac{C_1C_2V^2}{2(C_1+C_2)}=\dfrac{200\times3600}{60}\ \mu\text{J}$, or: fraction lost $=C_2/(C_1+C_2)=2/3$ of $18\ \text{mJ}$.

E5. JEE Main · MCQ An air capacitor has capacitance $C_0$. Its gap is filled as follows: the left half of the plate area by a material of dielectric constant $2$ across the full gap; the right half by two layers, each half the gap thick, of dielectric constants $3$ and $6$. The new capacitance is (A) $2C_0$ (B) $4C_0$ (C) $5C_0/2$ (D) $3C_0$

Left Half area, full gap, $K=2$: $\dfrac{2C_0}{2}=C_0$.
Right Half area, each layer half the gap: $K\times\tfrac12\times2C_0=KC_0$, i.e. $3C_0$ and $6C_0$ in series $=2C_0$.
Answer Left and right are in parallel: $C_0+2C_0=3C_0$, (D).
⏱ Shortcut Split by area $\to$ parallel; split by thickness $\to$ series. Halving the area halves $C$; halving the gap doubles it.

E6. JEE Main · Numerical A $20\ \text{pF}$ air capacitor is charged to $200\ \text{V}$ and disconnected from the supply. Its plates are then slowly pulled apart until their separation is doubled. Find the work done, in nanojoules. Give the answer to the nearest integer.

Before $U_1=\tfrac12CV^2=\tfrac12\times20\times10^{-12}\times4\times10^4=4.0\times10^{-7}\ \text{J}=400\ \text{nJ}$.
After $Q$ fixed, $C$ halves, so $U=Q^2/2C$ doubles: $U_2=800\ \text{nJ}$.
Answer $W=U_2-U_1=400$.
⏱ Shortcut The force $Q^2/2\varepsilon_0A$ is constant as the plates separate, so $W=F\Delta d$ and doubling $d$ adds exactly $U_1$.
🔬 Research–Teaching NexusResearch-tutored · optional, about 45 minutes

Research question. Does a home-made capacitor of kitchen foil and paper obey $C=K\varepsilon_0A/d$, and what is the dielectric constant of the paper?

Why it matters. Capacitive sensing is everywhere: phone and tablet touch screens, fuel-level gauges in aircraft, humidity sensors in weather stations, and the soil-moisture probes that let farmers in dry regions water only when crops need it. All of them work because a capacitance changes when the gap or the dielectric between two electrodes changes (Result 11.24). Measuring the dielectric constant of a material is also a standard test in the electrical industry — for cable insulation, circuit boards and the films inside the capacitors of electric-vehicle inverters.

What to do.

  1. Cut two rectangles of aluminium foil, about $15\ \text{cm}\times20\ \text{cm}$, each with a tab for connection. Measure the thickness of one sheet of printer paper by measuring a stack of $100$ sheets with a ruler or screw gauge.
  2. Place one, two, three, … up to eight sheets of paper between the foils, with a heavy book on top to press them flat. Measure the capacitance each time with a multimeter that has a capacitance range.
  3. Plot $C$ against $1/d$ (where $d$ is the total paper thickness). Is it a straight line? Find its slope, and from it $K=\text{slope}/(\varepsilon_0A)$.
  4. Repeat with a plastic sheet or a thin sheet of glass of the same total thickness and compare.
  5. Measure the capacitance with the foils slightly offset so that they overlap over only half the area. Does $C$ halve?

Tools: Aluminium foil, printer paper, a ruler or screw gauge, a multimeter with a capacitance range (or a simple RC timing circuit with a stopwatch), books for weight, a spreadsheet for the graph.

Hand in: Your table of $C$ and $d$, the graph of $C$ against $1/d$ with the fitted line, your value of $K$ for paper with an uncertainty, and a paragraph on the main sources of error (air gaps, edges, how hard the sheets are pressed).

Going further. Hold a hand flat a few millimetres above (not touching) the top foil and watch the reading. Explain the change — this is the principle of a touch sensor.

Instructor note: typical results are tens to a few hundred picofarads, and $K\approx2$–$4$ for paper — lower than the paper itself because thin air layers between sheets act as series capacitors (a good link to Result 11.25). The line of $C$ against $1/d$ usually misses the origin slightly because of stray capacitance in the leads; students should notice and discuss this.

🧪 Self-check quiz

0/5 correct

Q1. The capacitance of a parallel-plate capacitor does not depend on

Q2. Capacitors connected in series across a battery all have the same

Q3. A battery charges an initially uncharged capacitor fully. The fraction of the energy supplied by the battery that is stored in the capacitor is

Q4. With the battery still connected, a dielectric slab of constant $K$ is inserted to fill the gap of a capacitor. The charge on the plates

Q5. Which statement about polar molecules is correct?