Chapter 7 · Properties of Solids and Liquids

7.1 Elasticity

Stretch a wire, squeeze a liquid, shear a rubber pad: below the elastic limit the deformation is proportional to the load. Three moduli — Young's $Y$, bulk $B$ and rigidity $G$ — turn that one idea into numbers, and the energy stored is $\tfrac12\,\text{stress}\times\text{strain}$ per unit volume.

A crane lifts a 20-tonne container on a steel cable as thick as your wrist; the cable stretches by a few centimetres and springs back when the load is set down. A guitarist tunes a string by stretching it a fraction of a millimetre. A deep-sea submersible is squeezed so hard at the bottom of an ocean trench that its hull shrinks measurably. A building in an earthquake zone stands on thick rubber pads that let the ground slide sideways beneath it. In every case a solid is deformed by a force, and the engineer needs to know two things: how much it deforms, and whether it will return to its old shape when the force is removed.

Both questions are answered by the theory of elasticity. For small deformations, the deformation is simply proportional to the force that causes it — Hooke's law — and the constant of proportionality is a property of the material, not of the particular wire or block. In this section we define stress and strain, read the stress–strain curve of a metal, introduce the three elastic moduli (Young's modulus, the bulk modulus and the modulus of rigidity), and finish with the energy stored in a stretched wire. Along the way we meet the JEE Main favourites: composite wires, a rod stretched by its own weight, and a load that is released suddenly.

Elastic behaviour: stress and strain

A solid keeps its shape because its atoms sit at definite equilibrium distances from their neighbours, held there by interatomic forces. Pull the solid and the atoms move slightly apart; the interatomic forces then pull them back, like a three-dimensional network of tiny springs. Push it, and the atoms are squeezed closer and push back. As long as the atoms are only nudged from their places, they return exactly when the force is removed. If the force is large enough to make layers of atoms slip past one another, the solid cannot find its way back — it is permanently deformed.

📘 Definition 7.1 — Deforming force, elasticity and plasticity

A deforming force is an external force that changes the size or shape of a body. When a body is deformed, internal restoring forces arise that oppose the deformation; in equilibrium they balance the deforming force.

Elasticity is the property of a body by which it regains its original size and shape when the deforming force is removed. A body that does this completely is perfectly elastic; one that keeps its new shape is perfectly plastic. Plasticity is the property of being permanently deformed. Real bodies lie in between: steel and quartz are very nearly perfectly elastic for small loads, while putty, wet clay and soft lead are nearly plastic.

A thick rope stretches less than a thin one under the same load, and a long wire stretches more than a short one. To describe the material, rather than a particular sample, we divide the force by the area it is spread over and the change in size by the original size.

📘 Definition 7.2 — Stress

When a body is in equilibrium under a deforming force $F$ spread uniformly over an area $A$, the stress is the restoring force per unit area,

$$\sigma=\frac{F}{A}\qquad(\text{SI unit: N/m}^2=\text{Pa};\ \text{dimensions }[\mathrm{M\,L^{-1}T^{-2}}]).$$
  • Longitudinal stress: $F$ is perpendicular to $A$. It is tensile if it stretches the body, compressive if it squashes it.
  • Shearing (tangential) stress: $F$ is parallel to the face $A$, trying to slide one face over the opposite one.
  • Hydraulic (volume) stress: a uniform pressure $p$ acting normally on every part of the surface, as on a body under water. The stress is then the pressure change $\Delta p$.
📘 Definition 7.3 — Strain

Strain is the fractional deformation — a change in a dimension divided by its original value. It is a ratio of like quantities, so it is dimensionless and has no unit.

  • Longitudinal strain $\varepsilon=\dfrac{\Delta L}{L}$ (change in length over original length).
  • Volume strain $\dfrac{\Delta V}{V}$ (change in volume over original volume).
  • Shearing strain: if the top face of a block of height $L$ slides sideways by $\Delta x$ relative to the bottom face, the shearing strain is the angle $\theta$ through which the vertical edges turn, $\theta\approx\tan\theta=\dfrac{\Delta x}{L}$ (in radians, for small $\theta$).

Three remarks save marks. First, stress has the same unit as pressure, but stress can act along a surface (shear) as well as across it, and it is the internal restoring force per area; in equilibrium it equals the applied force per area. Second, the area in $\sigma=F/A$ is the cross-section perpendicular to $F$ for longitudinal stress, but the face parallel to $F$ for shearing stress. Third, a wire hanging a load has the same stress at every cross-section only if its own weight is negligible; we deal with heavy wires later.

✏️ Example 1 — Stress and strain in a loaded wire
A steel wire $2.0\ \text{m}$ long and $0.80\ \text{mm}$ in diameter hangs from a ceiling and carries a load of $8.0\ \text{kg}$. Its length increases by $1.56\ \text{mm}$. (a) Find the tensile stress and the longitudinal strain. (b) What is the ratio of stress to strain? (c) Find the stress if the same load hangs from a wire of the same steel with twice the diameter.
Area Radius $r=0.40\ \text{mm}=4.0\times10^{-4}\ \text{m}$: $A=\pi r^2=5.03\times10^{-7}\ \text{m}^2$. (Use the radius, not the diameter.)
(a) $F=mg=8.0\times9.8=78.4\ \text{N}$; $\ \sigma=\dfrac{78.4}{5.03\times10^{-7}}=1.56\times10^8\ \text{Pa}$. Strain $\varepsilon=\dfrac{1.56\times10^{-3}}{2.0}=7.8\times10^{-4}$ (no unit).
(b) $\dfrac{\sigma}{\varepsilon}=\dfrac{1.56\times10^8}{7.8\times10^{-4}}=2.0\times10^{11}\ \text{Pa}$ — a typical value for steel, as we shall see.
(c) Doubling the diameter makes the area $4$ times larger, so $\sigma=\dfrac{1.56\times10^8}{4}=3.9\times10^7\ \text{Pa}$.
Check Strain $7.8\times10^{-4}$ means the wire grew by $0.078\%$ — metals in their elastic range strain by well under $1\%$.

A wire carries a load $W$. It is replaced by a wire of the same material and the same diameter but half the length, carrying the same load (weights of the wires negligible). The tensile stress in the wire

Hooke's law and the stress–strain curve

Hang a wire from a rigid support, add loads one at a time, and measure the extension each time. For small loads the extension grows in exact proportion to the load: double the load, double the stretch. Converted to stress and strain, every wire of the same material gives the same straight line, whatever its length and thickness.

📐 Law 7.1 — Hooke's law

For small deformations — within the proportional limit of the material — stress is directly proportional to strain:

$$\text{stress}\propto\text{strain},\qquad \frac{\text{stress}}{\text{strain}}=\text{modulus of elasticity (a constant)} .$$

The constant depends on the material and on the type of deformation (tension, volume change or shear), and slightly on temperature; it does not depend on the size or shape of the sample. The law is empirical and holds for most solids only at small strains (typically below about $0.1$–$0.5\%$ for metals).

Keep loading a ductile metal wire and the straight line ends. A typical stress–strain curve for a ductile metal in tension (Interactive 1 draws one) has these landmarks, in order:

📘 Definition 7.4 — Landmarks on the stress–strain curve
  • Proportional limit: the end of the straight part; up to here Hooke's law holds.
  • Elastic limit (yield point): the greatest stress from which the wire still returns to its original length when unloaded. For most metals it lies just above the proportional limit. The stress there is the yield strength $\sigma_y$.
  • Plastic region: beyond the yield point the strain grows quickly for small increases of stress, and part of it is permanent. On unloading, the wire comes back along a line parallel to the original straight line and is left with a permanent set.
  • Ultimate tensile strength $\sigma_u$: the greatest stress the wire can bear. After this the wire thins locally ("necks") and soon breaks at the fracture point. The stress at which a material breaks is called its breaking stress; the corresponding force $F=\sigma_uA$ is the breaking load.

Materials differ in the shape of this curve. A ductile material (copper, mild steel, aluminium) has a long plastic region between the yield point and fracture — it can be drawn into wires. A brittle material (glass, cast iron, ceramics) breaks soon after its elastic limit, with almost no plastic region. Elastomers such as rubber and the elastin in blood vessels can be stretched to several times their length and still return, but their stress–strain curve is not a straight line at all, and the unloading curve lies below the loading curve: some energy is turned into heat in each cycle (this is called elastic hysteresis, and it is why rubber is used for shock absorbers).

Notice that the breaking load depends only on the cross-sectional area ($F=\sigma_uA$), not on the length. That leads to a neat question: how long can a wire be before it breaks under its own weight?

✏️ Example 2 — How long can a steel wire hang?
A steel has breaking stress $4.0\times10^8\ \text{Pa}$ and density $7.8\times10^3\ \text{kg/m}^3$. (a) A wire of this steel hangs vertically from a support. Find the greatest length it can have without breaking under its own weight. (b) A wire of this steel has diameter $2.0\ \text{mm}$. Ignoring its own weight, what is the largest mass it can support? (c) What happens to the answers to (a) and (b) if the wire is twice as thick?
Where? The top cross-section carries the weight of the whole wire below it, so the stress is greatest at the support: $\sigma_\text{top}=\dfrac{(\rho AL)g}{A}=\rho gL$.
(a) Breaking when $\rho gL=\sigma_u$: $L_{\max}=\dfrac{4.0\times10^8}{7.8\times10^3\times9.8}=5.2\times10^3\ \text{m}$, about $5\ \text{km}$. The area cancels.
(b) $F_{\max}=\sigma_uA=4.0\times10^8\times\pi(1.0\times10^{-3})^2=1.26\times10^3\ \text{N}$, i.e. a mass of $\dfrac{1257}{9.8}=128\ \text{kg}$.
(c) (a) is unchanged — a thicker wire is heavier in exactly the same proportion as it is stronger. (b) becomes $4$ times larger, $513\ \text{kg}$, since the area is $4$ times larger.
Insight The same reasoning limits the height of mountains: the rock at the base must bear the weight of the rock above it, so there is a greatest height (roughly $10\ \text{km}$ on Earth) beyond which the base would flow. Real cranes use a working stress several times smaller than the breaking stress — a factor of safety.

In the wire lab, choose steel and set the load to $300\ \text{N}$ (the wire is $2.0\ \text{m}$ long with a $1.0\ \text{mm}^2$ cross-section, so this is a stress of $300\ \text{MPa}$). Then slide the load back to $0$. What is the wire's length now?

At $150\ \text{N}$ the readouts show stress $150\ \text{MPa}$, strain $0.075\%$ and extension $1.5\ \text{mm}$ — still elastic. At $300\ \text{N}$ the wire is past its yield point ($250\ \text{MPa}$ in this model): strain about $1.13\%$, extension $22.5\ \text{mm}$. Unloading runs down a line parallel to the elastic line and leaves a permanent set of $19.5\ \text{mm}$ (the "permanent set" readout). Only the elastic part, $\sigma/Y=0.15\%$ of $2.0\ \text{m}$ $=3.0\ \text{mm}$, is recovered. The steel would break only near its ultimate strength, $400\ \text{MPa}$.
Interactive 1 — Wire-Stretching Lab: Hooke's Law and Beyond

A wire $2.0\ \text{m}$ long with a cross-section of $1.0\ \text{mm}^2$ carries the load you choose, so the stress in MPa equals the load in newtons. The graph plots stress against strain; its strain axis zooms out automatically once the wire yields. Increase the load past the yield line, then reduce it: the wire unloads along a line parallel to the elastic line and keeps a permanent set. Press Play for a full load–unload cycle. (Illustrative material data; in this simple model the proportional limit, elastic limit and yield point coincide. The wire's extension is drawn magnified.)

150 N
stress $\sigma$—
strain $\varepsilon$—
extension $\Delta L$—
permanent set if unloaded—

A copper wire is loaded until it is well past its yield point, and the load is then removed completely. Which statement is correct?

Young's modulus, bulk modulus and modulus of rigidity

Each kind of stress has its own kind of strain, so a material has three elastic moduli: one for stretching, one for squeezing from all sides and one for shearing. Each is defined by Hooke's law as stress ÷ strain, so each has the unit of stress, the pascal.

📘 Definition 7.5 — Young's modulus

For a wire or rod of length $L$ and cross-sectional area $A$ stretched (or compressed) by a force $F$ along its length, producing a change in length $\Delta L$, within the proportional limit, the Young's modulus of the material is

$$Y=\frac{\text{longitudinal stress}}{\text{longitudinal strain}}=\frac{F/A}{\Delta L/L}=\frac{FL}{A\,\Delta L}.$$

For most materials $Y$ is very nearly the same in tension and in compression.

📐 Result 7.2 — Extension of a wire; a wire as a spring

A light wire (own weight negligible) of length $L$, area $A$ and Young's modulus $Y$, loaded by $F$ within the proportional limit, extends by

$$\Delta L=\frac{FL}{AY}=\frac{4FL}{\pi d^2Y}\quad(d=\text{diameter}).$$

So the wire behaves like a spring of force constant $k=\dfrac{YA}{L}$. For two wires in series (end to end, same tension) the extensions add; for two wires sharing a load in parallel (same extension) the tensions add.

Young's modulus is measured with a long, thin wire, so that the extension is large enough to read. In the standard laboratory set-up two identical wires hang side by side from the same rigid beam: the reference wire carries a fixed small load and a main scale, the experimental wire carries a vernier and the load pan. Measuring the extension of one wire relative to the other cancels the sagging of the beam and any expansion due to temperature changes. The wire's diameter is measured with a screw gauge at several places; loads are added in steps, and the extension is read both while loading and unloading. A graph of extension against load is a straight line whose slope gives $Y$.

✏️ Example 3 — Young's modulus from a laboratory graph
In a Young's modulus experiment the wire is $2.50\ \text{m}$ long and its diameter is $0.500\ \text{mm}$. Loads of $1.0$, $2.0$, $3.0$, $4.0$ and $5.0\ \text{kg}$ give extensions of $0.62$, $1.25$, $1.88$, $2.49$ and $3.12\ \text{mm}$. (a) Find $Y$ from the slope of the graph. (b) The diameter is known to $\pm0.005\ \text{mm}$, the length to $\pm1\ \text{mm}$ and the largest extension to $\pm0.01\ \text{mm}$. Estimate the maximum percentage error in $Y$ and say which measurement limits the accuracy.
Find $Y$ before you open the solution:
Slope The points lie on a straight line through the origin (Hooke's law holds). Slope $=\dfrac{3.12-0.62}{5.0-1.0}=0.625\ \text{mm/kg}=6.25\times10^{-4}\ \text{m/kg}$.
(a) $A=\pi(2.50\times10^{-4})^2=1.96\times10^{-7}\ \text{m}^2$. Since $\Delta L=\dfrac{mgL}{AY}$, the slope is $\dfrac{gL}{AY}$, so $Y=\dfrac{gL}{A\times\text{slope}}=\dfrac{9.8\times2.50}{1.96\times10^{-7}\times6.25\times10^{-4}}=2.0\times10^{11}\ \text{Pa}$.
(b) $Y=\dfrac{4mgL}{\pi d^2\,\Delta L}$, so $\dfrac{\Delta Y}{Y}=\dfrac{\Delta L_\text{len}}{L}+2\dfrac{\Delta d}{d}+\dfrac{\delta(\Delta L)}{\Delta L}=0.04\%+2(1.0\%)+0.32\%\approx2.4\%$.
Verdict The diameter term, doubled because $d$ is squared, dominates. That is why the diameter is measured at several places along the wire and in two perpendicular directions, and why a long, thin wire is used (large $\Delta L$, so its relative error is small).

Composite and heavy wires. When two wires are joined end to end and carry a load $F$, each carries the same tension $F$, so $\Delta L=F\left(\dfrac{L_1}{A_1Y_1}+\dfrac{L_2}{A_2Y_2}\right)$ — exactly like springs in series. When a wire is heavy, the tension is no longer the same all along it: at a distance $x$ above the lower end of a uniform wire of total mass $M$ and length $L$ hanging freely, the tension supports the part below, $T(x)=Mg\,x/L$. A short element $dx$ there stretches by $\dfrac{T(x)\,dx}{AY}$, and adding up (integrating) from $0$ to $L$:

$$\Delta L=\int_0^L\frac{Mg\,x}{L\,AY}\,dx=\frac{MgL}{2AY}=\frac{\rho gL^2}{2Y}.$$
📐 Result 7.3 — A wire or rod stretched by a non-uniform tension

For a uniform wire of mass $M$, length $L$, area $A$ and Young's modulus $Y$ (within the proportional limit):

  • hanging under its own weight: $\Delta L=\dfrac{MgL}{2AY}=\dfrac{\rho gL^2}{2Y}$ — half the extension a light wire would have with the load $Mg$ hung from its end;
  • own weight plus a load $mg$ at the lower end: $\Delta L=\dfrac{(m+M/2)\,gL}{AY}$;
  • a free rod on a smooth floor pulled at one end by $F$ (so it accelerates): the tension falls linearly from $F$ at the pulled end to $0$ at the far end, and $\Delta L=\dfrac{FL}{2AY}$.

In each case the extension equals that of a light wire carrying the average tension.

✏️ Example 4 — A steel wire and a brass wire in series
A steel wire $1.5\ \text{m}$ long and a brass wire $1.0\ \text{m}$ long, both of diameter $1.0\ \text{mm}$, are joined end to end. The combination hangs from a ceiling with the steel wire on top and carries a $10\ \text{kg}$ load at the lower end. $Y_\text{steel}=2.0\times10^{11}\ \text{Pa}$, $Y_\text{brass}=0.90\times10^{11}\ \text{Pa}$; the wires' own weights are negligible. Find (a) the stress in each wire, (b) the extension of each wire and the total extension, (c) the ratio of the strains $\varepsilon_\text{steel}:\varepsilon_\text{brass}$.
Find the total extension before you open the solution:
Tension Each wire is in equilibrium and the wires are light, so both carry the full load: $T=10\times9.8=98\ \text{N}$. $A=\pi(5.0\times10^{-4})^2=7.85\times10^{-7}\ \text{m}^2$.
(a) Same $T$ and same $A$: $\sigma=\dfrac{98}{7.85\times10^{-7}}=1.25\times10^8\ \text{Pa}$ in both wires.
(b) $\Delta L_s=\dfrac{98\times1.5}{7.85\times10^{-7}\times2.0\times10^{11}}=0.94\ \text{mm}$; $\ \Delta L_b=\dfrac{98\times1.0}{7.85\times10^{-7}\times0.90\times10^{11}}=1.39\ \text{mm}$. Total $2.32\ \text{mm}$.
(c) Same stress, so strain $\propto1/Y$: $\dfrac{\varepsilon_s}{\varepsilon_b}=\dfrac{Y_b}{Y_s}=\dfrac{0.90}{2.0}=0.45$. (Check: $\dfrac{0.94/1.5}{1.39/1.0}=0.45$ ✓.)
⏱ Shortcut Treat each wire as a spring $k=YA/L$: $k_s=1.05\times10^5\ \text{N/m}$, $k_b=7.07\times10^4\ \text{N/m}$; in series $\dfrac1k=\dfrac1{k_s}+\dfrac1{k_b}$ gives $k=4.22\times10^4\ \text{N/m}$ and $\Delta L=98/k=2.32\ \text{mm}$.
📘 Definition 7.6 — Bulk modulus and compressibility

When the pressure on a body is increased uniformly by $\Delta p$ (hydraulic stress) and its volume changes from $V$ to $V+\Delta V$, the bulk modulus is

$$B=-\frac{\Delta p}{\Delta V/V}=-V\frac{\Delta p}{\Delta V}.$$

The minus sign makes $B$ positive, since an increase in pressure decreases the volume. The reciprocal $K=\dfrac1B$ is the compressibility (unit $\text{Pa}^{-1}$): the fractional decrease in volume per unit increase in pressure. Solids, liquids and gases all have a bulk modulus.

Because the mass of the body does not change, a small fractional decrease in volume is a fractional increase in density of the same size: $\dfrac{\Delta\rho}{\rho}\approx-\dfrac{\Delta V}{V}=\dfrac{\Delta p}{B}$. Liquids and solids have bulk moduli of the order of $10^9$–$10^{11}\ \text{Pa}$, so even huge pressures change their volume by only a few per cent; gases are about $10^4$ times more compressible.

📘 Definition 7.7 — Modulus of rigidity (shear modulus)

When a tangential force $F$ acts on a face of area $A$ of a block whose opposite face is fixed, and the block is sheared through a small angle $\theta$ (the top face moves by $\Delta x$ over a height $L$, $\theta\approx\Delta x/L$), the modulus of rigidity (shear modulus) is

$$G=\frac{\text{shearing stress}}{\text{shearing strain}}=\frac{F/A}{\theta}=\frac{FL}{A\,\Delta x}.$$

Only solids have a modulus of rigidity. A fluid at rest cannot resist a shearing stress at all — it flows — so liquids and gases have only a bulk modulus. For most metals $G$ is roughly a third to a half of $Y$.

Material (approximate values)$Y$ (Pa)$G$ (Pa)$B$ (Pa)
steel$2.0\times10^{11}$$8.0\times10^{10}$$1.6\times10^{11}$
copper$1.1\times10^{11}$$4.2\times10^{10}$$1.4\times10^{11}$
aluminium$7.0\times10^{10}$$2.5\times10^{10}$$7.5\times10^{10}$
glass$6.5\times10^{10}$$2.6\times10^{10}$$4.0\times10^{10}$
water——$2.2\times10^{9}$
air (at $1\ \text{atm}$, constant temperature)——$1.0\times10^{5}$
✏️ Example 5 — Squeezing sea water and shearing a rubber bearing
(a) At a certain depth in the ocean the pressure is $4.0\times10^7\ \text{Pa}$ greater than at the surface. Taking $B=2.2\times10^9\ \text{Pa}$ for sea water and its surface density as $1030\ \text{kg/m}^3$, find the fractional change in volume of a sample of water brought down there, and its density there. (b) A building rests on rubber base-isolation bearings. One bearing is a block $0.40\ \text{m}\times0.40\ \text{m}$ in plan and $0.20\ \text{m}$ high, with $G=8.0\times10^5\ \text{Pa}$. During an earthquake the ground exerts a horizontal force of $16\ \text{kN}$ on its bottom face while its top face is held by the building. Find the shearing strain and the sideways displacement of the bottom relative to the top.
(a) volume $\dfrac{\Delta V}{V}=-\dfrac{\Delta p}{B}=-\dfrac{4.0\times10^7}{2.2\times10^9}=-1.8\times10^{-2}$: the volume falls by $1.8\%$.
(a) density Mass is unchanged, so $\rho'=\dfrac{\rho}{1-0.0182}=\dfrac{1030}{0.982}=1.05\times10^3\ \text{kg/m}^3$ (to 3 s.f., $1049\ \text{kg/m}^3$) — water is almost, but not quite, incompressible.
(b) stress The force acts along the $0.40\times0.40=0.16\ \text{m}^2$ face: shearing stress $=\dfrac{1.6\times10^4}{0.16}=1.0\times10^5\ \text{Pa}$.
(b) strain $\theta=\dfrac{1.0\times10^5}{8.0\times10^5}=0.125\ \text{rad}$; displacement $\Delta x=\theta L=0.125\times0.20=0.025\ \text{m}=25\ \text{mm}$.
Note The area in the shear modulus is the face along which the force acts, and $L$ is the height perpendicular to that face. A soft pad (small $G$) lets the ground move under the building without the building having to follow at once.

Which elastic modulus (or moduli) does water at rest possess?

Elastic potential energy of a stretched wire

Stretching a wire takes work, because the restoring force opposes the stretch. Within the proportional limit the wire is a spring of constant $k=YA/L$: when its extension is $x$, the force needed to hold it there is $F(x)=\dfrac{YA}{L}x$. Stretching it slowly from $x=0$ to $x=\Delta L$, the work done is the area under the force–extension line:

$$W=\int_0^{\Delta L}\frac{YA}{L}\,x\,dx=\frac12\,\frac{YA}{L}(\Delta L)^2=\frac12F\,\Delta L ,$$

where $F$ is the final load. This work is stored as elastic potential energy in the stretched interatomic "springs", and is given back when the wire contracts. Dividing by the volume $AL$ of the wire and using $\sigma=F/A$, $\varepsilon=\Delta L/L$ gives the energy per unit volume.

📐 Result 7.4 — Elastic potential energy

A wire stretched slowly, within the proportional limit, by a final load $F$ to an extension $\Delta L$ stores

$$U=\tfrac12F\,\Delta L=\frac{YA}{2L}(\Delta L)^2=\frac{F^2L}{2AY}.$$

The energy per unit volume (energy density) is

$$u=\frac{U}{AL}=\tfrac12\,\sigma\,\varepsilon=\frac{\sigma^2}{2Y}=\tfrac12Y\varepsilon^2 .$$

The factor $\tfrac12$ comes from the force growing from $0$ to $F$ during the stretch; it is not $F\Delta L$. That matters most when a load is attached and released suddenly. Then the load's weight $mg$ is constant all the way down, while the wire's pull $kx$ starts from zero. The load accelerates until $kx=mg$, overshoots, and comes to rest momentarily where all the lost gravitational energy is stored in the wire: $mg\,x_{\max}=\tfrac12kx_{\max}^2$, so $x_{\max}=2mg/k$ — twice the equilibrium extension, with twice the stress. The load then oscillates and, with friction in the wire, settles at $x_0=mg/k$. Gravity has done work $mgx_0$, the wire stores $\tfrac12mgx_0$, and the other half has become heat. Interactive 2 shows this.

Elasticity in engineering. Designers choose sizes so that stresses stay well inside the elastic range. A crane cable is made of many thin steel strands, for flexibility, with a total area chosen so that the working stress is a fraction of the breaking stress (a factor of safety of about $4$–$6$), and with allowance for the extra tension while the load accelerates. A beam carrying a load sags by an amount proportional to $1/Y$ and, for a rectangular section, to $1/(bd^3)$ where $b$ is its breadth and $d$ its depth; so a beam is laid with its larger dimension vertical, and girders are given an "I" section, which puts most of the material far from the centre where it resists bending best.

✏️ Example 6 — Gradual and sudden loading of a steel wire
A steel wire ($Y=2.0\times10^{11}\ \text{Pa}$) $3.0\ \text{m}$ long with a cross-section of $2.0\ \text{mm}^2$ hangs from a rigid support. (a) A $20\ \text{kg}$ load is lowered onto it gently until it hangs at rest. Find the extension, the energy stored and the energy stored per unit volume. (b) Instead, the load is attached to the unstretched wire and released from rest. Find the greatest extension and the greatest stress. (c) In case (b), when the oscillations have died away, how much energy has been turned into heat?
Find the energy stored in case (a) before you open the solution:
Spring $k=\dfrac{YA}{L}=\dfrac{2.0\times10^{11}\times2.0\times10^{-6}}{3.0}=1.33\times10^5\ \text{N/m}$; $F=mg=196\ \text{N}$.
(a) $\Delta L=\dfrac{F}{k}=1.47\times10^{-3}\ \text{m}=1.47\ \text{mm}$. $U=\tfrac12F\Delta L=\tfrac12\times196\times1.47\times10^{-3}=0.144\ \text{J}$. Volume $AL=6.0\times10^{-6}\ \text{m}^3$, so $u=\dfrac{0.144}{6.0\times10^{-6}}=2.4\times10^4\ \text{J/m}^3$.
(b) At the lowest point the load is momentarily at rest: $mg\,x_{\max}=\tfrac12kx_{\max}^2$, so $x_{\max}=\dfrac{2mg}{k}=2.94\ \text{mm}$. Greatest stress $=\dfrac{kx_{\max}}{A}=\dfrac{392}{2.0\times10^{-6}}=1.96\times10^8\ \text{Pa}$ — twice the static stress $9.8\times10^7\ \text{Pa}$, though still below the yield strength of steel.
(c) Finally the load rests at $1.47\ \text{mm}$: gravity has done $mg\Delta L=0.288\ \text{J}$, the wire stores $0.144\ \text{J}$, so $0.144\ \text{J}$ has become heat (in the wire and the air).
Check $u=\dfrac{\sigma^2}{2Y}=\dfrac{(9.8\times10^7)^2}{4.0\times10^{11}}=2.4\times10^4\ \text{J/m}^3$ ✓, and $u=\tfrac12\sigma\varepsilon=\tfrac12(9.8\times10^7)(4.9\times10^{-4})$ ✓.

In Interactive 2, keep the wire at $1.0\ \text{mm}^2$, set the mass to $10\ \text{kg}$ and choose sudden release. What is the greatest extension of the wire?

With $k=YA/L=1.0\times10^5\ \text{N/m}$ the readouts show static extension $0.98\ \text{mm}$ and, for sudden release, peak extension $1.96\ \text{mm}$ with peak stress $196\ \text{MPa}$ (gentle loading: $98\ \text{MPa}$). At the lowest point the load is momentarily at rest, so all of gravity's work $mgx_{\max}$ is stored: $mgx_{\max}=\tfrac12kx_{\max}^2$ gives $x_{\max}=2mg/k$. The stored energy at rest is $48.0\ \text{mJ}$ in both modes; in sudden release another $48.0\ \text{mJ}$ ends up as heat.
Interactive 2 — Gentle versus Sudden Loading: Where the Energy Goes

A steel wire ($Y=2.0\times10^{11}\ \text{Pa}$, length $2.0\ \text{m}$) carries a mass $m$. Choose how the mass is attached and press Play (the motion is shown in slow motion; the wire's extension is magnified). On the force–extension graph the black line is the wire's pull $kx$, the dashed line the weight $mg$. The green triangle is the energy stored at equilibrium, $\tfrac12mgx_0$; the amber triangle is the equal amount of gravity's work that is not stored — taken by your hand in gentle loading, turned into kinetic energy and then heat in sudden release.

10 kg1.0 mm²
static extension $x_0$—
peak extension, peak stress—
stored at rest $\tfrac12kx_0^2$—
not stored (hand or heat)—
🧭 Problem-solving strategy — Elasticity problems
  1. Identify the deformation: change of length ($Y$), change of volume under pressure ($B$) or change of shape by a tangential force ($G$).
  2. Convert everything to SI: $\text{mm}\to\text{m}$, $\text{mm}^2=10^{-6}\ \text{m}^2$, $\text{cm}^2=10^{-4}\ \text{m}^2$; find the area from the radius.
  3. Find the force at the cross-section that matters. If the tension varies (heavy wire, accelerating rod), use the average tension for the extension and the largest tension for breaking.
  4. For wires in series or parallel, use $k=YA/L$ and combine like springs.
  5. For energy, use $\tfrac12F\Delta L$ for slow loading; for sudden loading, use energy conservation with $mg$ constant.
  6. For ratio questions, write the formula as a proportionality first ($\Delta L\propto FL/(d^2Y)$) and cancel what is common.
⚠️ JEE Main traps

1. Diameter for radius, mm² for m². $A=\pi r^2=\pi d^2/4$, and $1\ \text{mm}^2=10^{-6}\ \text{m}^2$ (not $10^{-3}$). Most wrong answers in elasticity are off by a factor of $4$ or a power of ten.

2. Thinking $Y$ depends on the sample. $Y$, $B$ and $G$ are properties of the material. A longer or thinner wire stretches more, but its Young's modulus is the same. Cutting a wire in half halves its extension and doubles its spring constant $k=YA/L$.

3. Own weight counts half. A heavy wire hanging freely stretches by $\dfrac{MgL}{2AY}$, not $\dfrac{MgL}{AY}$; with a load as well, use $(m+M/2)g$. But for the breaking condition the full weight acts at the top.

4. Energy is $\tfrac12F\Delta L$, not $F\Delta L$. And a suddenly applied load produces twice the static extension and stress at the lowest point.

5. Breaking load depends on area only. Changing the length of a wire does not change the load at which it snaps; doubling the diameter multiplies the breaking load by $4$.

The extension of a wire, within its proportional limit, is doubled by doubling the load. The elastic energy stored in the wire becomes

Exercises

Take $g=9.8\ \text{m/s}^2$ unless a part says otherwise. Neglect the weight of a wire unless told to include it, and assume every deformation is within the proportional limit unless stated. $Y_\text{steel}=2.0\times10^{11}\ \text{Pa}$ where needed.

I
Stress, strain and Hooke's law.
  • 1 A $5.0\ \text{kg}$ mass hangs from a wire of cross-sectional area $2.0\ \text{mm}^2$. Find the tensile stress in the wire.
  • 2 A wire $1.5\ \text{m}$ long stretches by $0.60\ \text{mm}$. Find the longitudinal strain.
  • 3 A copper wire ($Y=1.1\times10^{11}\ \text{Pa}$) has a longitudinal strain of $5.0\times10^{-4}$. Find the stress in it.
  • 4 A steel rod $0.80\ \text{m}$ long and $2.0\ \text{cm}$ in diameter supports a compressive load of $1.0\times10^4\ \text{N}$. Find the stress, the strain and the decrease in length.
  • 5 Write the dimensional formulae of stress, strain and Young's modulus. Why can stress and pressure share a unit and yet be different quantities?
  • 6 Wire A has length $L$ and diameter $d$; wire B, of the same material, has length $2L$ and diameter $2d$. Both carry the same load. Find $\Delta L_A/\Delta L_B$.
  • 7 The load–extension graph of a wire $2.0\ \text{m}$ long with area $0.50\ \text{mm}^2$ is a straight line through the origin up to $40\ \text{N}$, where the extension is $0.80\ \text{mm}$. Find Young's modulus of the material.
  • 8 A material has breaking stress $5.0\times10^8\ \text{Pa}$ and density $8.0\times10^3\ \text{kg/m}^3$. Taking $g=10\ \text{m/s}^2$, find the greatest length of a wire of this material that can hang vertically without breaking under its own weight.
1 $\sigma=\dfrac{5.0\times9.8}{2.0\times10^{-6}}=2.45\times10^7\ \text{Pa}$.
2 $\varepsilon=\dfrac{0.60\times10^{-3}}{1.5}=4.0\times10^{-4}$ (no unit).
3 $\sigma=Y\varepsilon=1.1\times10^{11}\times5.0\times10^{-4}=5.5\times10^7\ \text{Pa}$.
4 $A=\pi(0.010)^2=3.14\times10^{-4}\ \text{m}^2$; $\sigma=3.18\times10^7\ \text{Pa}$ (compressive); $\varepsilon=\dfrac{3.18\times10^7}{2.0\times10^{11}}=1.59\times10^{-4}$; $\Delta L=1.59\times10^{-4}\times0.80=1.27\times10^{-4}\ \text{m}=0.127\ \text{mm}$.
5 Stress $[\mathrm{M\,L^{-1}T^{-2}}]$; strain dimensionless; $Y$ $[\mathrm{M\,L^{-1}T^{-2}}]$. Pressure is a normal force per area exerted by a fluid and is the same in all directions at a point; stress is the internal restoring force per area in a solid and can be tensile, compressive or tangential, depending on the face considered.
6 $\Delta L\propto\dfrac{L}{d^2}$: $\dfrac{\Delta L_A}{\Delta L_B}=\dfrac{L/d^2}{2L/4d^2}=2$.
7 $Y=\dfrac{FL}{A\Delta L}=\dfrac{40\times2.0}{0.50\times10^{-6}\times0.80\times10^{-3}}=2.0\times10^{11}\ \text{Pa}$.
8 $L_{\max}=\dfrac{\sigma_u}{\rho g}=\dfrac{5.0\times10^8}{8.0\times10^3\times10}=6.25\times10^3\ \text{m}$.
II
Young's modulus, bulk modulus and modulus of rigidity.
  • 1 A steel wire $4.0\ \text{m}$ long and $1.0\ \text{mm}$ in diameter carries a $20\ \text{kg}$ load. Find its extension.
  • 2 A copper block of volume $2.0\times10^{-4}\ \text{m}^3$ ($B=1.4\times10^{11}\ \text{Pa}$) is placed in a press where the pressure on it is raised by $1.0\times10^8\ \text{Pa}$. Find the fractional and the actual decrease in its volume.
  • 3 What increase of pressure is needed to reduce the volume of water ($B=2.2\times10^9\ \text{Pa}$) by $0.10\%$?
  • 4 Find the compressibility of water from the data in part 3.
  • 5 An aluminium cube of edge $10\ \text{cm}$ ($G=2.5\times10^{10}\ \text{Pa}$) has its lower face fixed. A tangential force of $1.0\times10^5\ \text{N}$ acts on its upper face. Find the shearing strain and the sideways displacement of the upper face.
  • 6 Which of $Y$, $B$, $G$ are possessed by (a) a steel rod, (b) water, (c) air? Explain the difference.
  • 7 Load–extension graphs (load on the vertical axis, extension on the horizontal) for two wires A and B of the same length and cross-section are straight lines through the origin making angles of $60^\circ$ and $30^\circ$ with the extension axis. Find $Y_A/Y_B$.
  • 8 A copper rod ($\rho=8.9\times10^3\ \text{kg/m}^3$, $Y=1.1\times10^{11}\ \text{Pa}$) $2.0\ \text{m}$ long hangs vertically from one end. Find its extension due to its own weight.
1 $A=7.85\times10^{-7}\ \text{m}^2$; $\Delta L=\dfrac{196\times4.0}{7.85\times10^{-7}\times2.0\times10^{11}}=4.99\times10^{-3}\ \text{m}\approx5.0\ \text{mm}$.
2 $\dfrac{|\Delta V|}{V}=\dfrac{1.0\times10^8}{1.4\times10^{11}}=7.1\times10^{-4}$; $|\Delta V|=7.1\times10^{-4}\times2.0\times10^{-4}=1.4\times10^{-7}\ \text{m}^3=0.14\ \text{cm}^3$.
3 $\Delta p=B\dfrac{|\Delta V|}{V}=2.2\times10^9\times1.0\times10^{-3}=2.2\times10^6\ \text{Pa}$ — about $22$ atmospheres.
4 $K=\dfrac1B=4.5\times10^{-10}\ \text{Pa}^{-1}$.
5 Stress $=\dfrac{1.0\times10^5}{0.010}=1.0\times10^7\ \text{Pa}$; $\theta=\dfrac{1.0\times10^7}{2.5\times10^{10}}=4.0\times10^{-4}\ \text{rad}$; $\Delta x=\theta L=4.0\times10^{-5}\ \text{m}=0.040\ \text{mm}$.
6 (a) all three; (b) and (c) only $B$. A fluid flows under any shearing stress, so it has no rigidity and no fixed length; it resists only compression. Air's $B$ is about $10^4$ times smaller than water's.
7 With load $F$ against extension $x$, the slope $F/x=YA/L$; same $A$ and $L$, so $\dfrac{Y_A}{Y_B}=\dfrac{\tan60^\circ}{\tan30^\circ}=3$.
8 $\Delta L=\dfrac{\rho gL^2}{2Y}=\dfrac{8.9\times10^3\times9.8\times4.0}{2\times1.1\times10^{11}}=1.6\times10^{-6}\ \text{m}$ — about $1.6\ \mu\text{m}$.
III
Combinations of wires and elastic energy.
  • 1 A steel wire and a copper wire ($Y_c=1.1\times10^{11}\ \text{Pa}$) of the same length and cross-section are joined end to end and carry a load. Find the ratio of their stresses and of their extensions $\Delta L_s/\Delta L_c$.
  • 2 Find the force constant of a steel wire $2.0\ \text{m}$ long with a cross-section of $1.0\ \text{mm}^2$.
  • 3 How much elastic energy is stored in the wire of part 2 when it is stretched by $1.0\ \text{mm}$?
  • 4 Find the elastic energy per unit volume in steel under a tensile stress of $1.0\times10^8\ \text{Pa}$.
  • 5 A wire stretches by $2.0\ \text{mm}$ under a load of $100\ \text{N}$ applied gradually. Find the energy stored. What would it be if the load were increased (still within the proportional limit) to give an extension of $4.0\ \text{mm}$?
  • 6 A light rigid rod $1.0\ \text{m}$ long hangs horizontally from two vertical wires of the same length and cross-section, a steel wire at the left end and a wire with $Y=1.0\times10^{11}\ \text{Pa}$ at the right end. How far from the steel end must a load be hung for the rod to stay horizontal?
  • 7 In the arrangement of part 6, where must the load be hung for the two wires to have equal stress? Does the rod then stay horizontal?
  • 8 A wire of force constant $2.0\times10^4\ \text{N/m}$ hangs vertically. A $4.0\ \text{kg}$ mass is attached to its free end while the wire is unstretched and released from rest. Find the greatest extension.
1 Same tension and area, so stresses are equal ($1:1$). Extensions $\propto1/Y$: $\dfrac{\Delta L_s}{\Delta L_c}=\dfrac{1.1}{2.0}=0.55$.
2 $k=\dfrac{YA}{L}=\dfrac{2.0\times10^{11}\times1.0\times10^{-6}}{2.0}=1.0\times10^5\ \text{N/m}$.
3 $U=\tfrac12k(\Delta L)^2=\tfrac12\times10^5\times(1.0\times10^{-3})^2=0.050\ \text{J}$.
4 $u=\dfrac{\sigma^2}{2Y}=\dfrac{10^{16}}{4.0\times10^{11}}=2.5\times10^4\ \text{J/m}^3$.
5 $U=\tfrac12\times100\times2.0\times10^{-3}=0.10\ \text{J}$. Doubling the extension doubles the load too, so $U$ becomes $4\times0.10=0.40\ \text{J}$.
6 Horizontal rod means equal extensions, so tensions $\propto YA/L$: $T_s=2T_2$. Moments about the load point (distance $x$ from the steel end): $T_sx=T_2(1.0-x)$, so $2x=1.0-x$ and $x=0.333\ \text{m}$ from the steel end.
7 Equal stresses with equal areas need equal tensions: the load must hang at the middle, $0.50\ \text{m}$ from either end. The wires then stretch unequally (the right-hand wire twice as much), so the rod tilts down on the right.
8 Sudden loading: $x_{\max}=\dfrac{2mg}{k}=\dfrac{2\times4.0\times9.8}{2.0\times10^4}=3.92\times10^{-3}\ \text{m}=3.92\ \text{mm}$ (twice the equilibrium extension $1.96\ \text{mm}$).
IV
Harder problems and applications.
  • 1 A steel cable $100\ \text{m}$ long with a cross-section of $1.0\ \text{cm}^2$ ($\rho=7.8\times10^3\ \text{kg/m}^3$) hangs down a mine shaft carrying a $500\ \text{kg}$ cage at rest. Find its extension, including the effect of its own weight.
  • 2 A steel rod $2.0\ \text{m}$ long with a cross-section of $1.0\ \text{cm}^2$ lies on a smooth floor and is pulled along its length by a force of $1.0\times10^4\ \text{N}$ at one end. Find its extension. Compare it with the extension when the rod is fixed at one end and pulled with the same force at the other.
  • 3 For the accelerating rod of part 2, find the stress at its midpoint.
  • 4 A $0.50\ \text{kg}$ puck tied to a steel wire $1.0\ \text{m}$ long with a cross-section of $1.0\ \text{mm}^2$ is whirled in a horizontal circle on smooth ice at $20\ \text{rad/s}$, the other end of the wire being fixed. Find the extension of the wire (the change in radius is small).
  • 5 At the deepest point of the ocean the pressure is about $1.1\times10^8\ \text{Pa}$ above atmospheric. By what fraction is the volume of a steel sphere ($B=1.6\times10^{11}\ \text{Pa}$) reduced there? Compare with water ($B=2.2\times10^9\ \text{Pa}$, treated as constant).
  • 6 (Modelling) A crane must lift a $2.0$-tonne load with an upward acceleration of up to $1.0\ \text{m/s}^2$. The steel of the cable breaks at $4.0\times10^8\ \text{Pa}$ and the working stress must not exceed a quarter of this. Find the least diameter of the cable (treat it as a solid rod).
  • 7 Wires A and B of the same material and length carry the same load; the radius of A is twice that of B. Find the ratio $U_A/U_B$ of the elastic energies stored.
  • 8 A catapult's rubber cord is $10\ \text{cm}$ long with a cross-section of $1.0\ \text{mm}^2$; for this rubber take $Y=5.0\times10^8\ \text{Pa}$ (Hooke's law assumed). The cord is stretched by $5.0\ \text{cm}$ and releases a $5.0\ \text{g}$ stone. Assuming all the stored energy goes to the stone, find its speed.
1 Cable mass $M=\rho AL=7.8\times10^3\times10^{-4}\times100=78\ \text{kg}$. $\Delta L=\dfrac{(m+M/2)gL}{AY}=\dfrac{(500+39)\times9.8\times100}{10^{-4}\times2.0\times10^{11}}=2.64\times10^{-2}\ \text{m}=26.4\ \text{mm}$.
2 The tension falls from $F$ to $0$ along the rod; average $F/2$: $\Delta L=\dfrac{FL}{2AY}=\dfrac{1.0\times10^4\times2.0}{2\times10^{-4}\times2.0\times10^{11}}=5.0\times10^{-4}\ \text{m}=0.50\ \text{mm}$. A fixed rod pulled with $F$ has tension $F$ throughout: $1.0\ \text{mm}$, twice as much.
3 The half of the rod behind the midpoint has half the mass and the common acceleration $F/m$, so the tension there is $F/2=5.0\times10^3\ \text{N}$; stress $=\dfrac{5.0\times10^3}{10^{-4}}=5.0\times10^7\ \text{Pa}$.
4 The tension provides the centripetal force: $T=m\omega^2r=0.50\times400\times1.0=200\ \text{N}$; $\Delta L=\dfrac{200\times1.0}{10^{-6}\times2.0\times10^{11}}=1.0\times10^{-3}\ \text{m}=1.0\ \text{mm}$.
5 Steel: $\dfrac{1.1\times10^8}{1.6\times10^{11}}=6.9\times10^{-4}$, i.e. $0.069\%$. Water: $\dfrac{1.1\times10^8}{2.2\times10^9}=0.050$, i.e. $5.0\%$ — about $70$ times more.
6 Greatest tension $T=m(g+a)=2000\times10.8=2.16\times10^4\ \text{N}$; allowed stress $1.0\times10^8\ \text{Pa}$; $A_{\min}=2.16\times10^{-4}\ \text{m}^2$; $d=\sqrt{4A/\pi}=1.66\times10^{-2}\ \text{m}=16.6\ \text{mm}$.
7 $U=\dfrac{F^2L}{2AY}\propto\dfrac1A$; $A_A=4A_B$, so $\dfrac{U_A}{U_B}=\dfrac14$.
8 $k=\dfrac{YA}{L}=\dfrac{5.0\times10^8\times10^{-6}}{0.10}=5.0\times10^3\ \text{N/m}$; $U=\tfrac12k x^2=\tfrac12\times5000\times0.050^2=6.25\ \text{J}$; $\tfrac12mv^2=6.25$ gives $v=\sqrt{\dfrac{2\times6.25}{0.0050}}=50\ \text{m/s}$.
🎯 Exam corner JEE Main · MCQJEE Main · Numerical

E1. JEE Main · MCQ Two wires P and Q are made of the same material. The length of P is half that of Q, and the diameter of P is twice that of Q. When equal loads are hung from them, the ratio of the extension of P to that of Q is (A) $1:4$ (B) $2:1$ (C) $1:8$ (D) $8:1$

Idea $\Delta L=\dfrac{4FL}{\pi d^2Y}\propto\dfrac{L}{d^2}$ for the same load and material.
Ratio $\dfrac{\Delta L_P}{\Delta L_Q}=\dfrac{L_P}{L_Q}\cdot\dfrac{d_Q^2}{d_P^2}=\dfrac12\times\dfrac14=\dfrac18$.
Answer (C) $1:8$.
⏱ Shortcut (A) forgets the length; (D) inverts the ratio. Write $\Delta L\propto L/d^2$ first and the arithmetic takes ten seconds.

E2. JEE Main · Numerical A steel wire ($Y=2.0\times10^{11}\ \text{Pa}$) of cross-sectional area $1.0\ \text{mm}^2$ hangs vertically. What mass, in kg, must be hung from it to increase its length by $0.10\%$? Take $g=10\ \text{m/s}^2$. Give the answer to the nearest integer.

Strain $0.10\%$ means $\varepsilon=1.0\times10^{-3}$ — the length of the wire is not needed.
Force $F=YA\varepsilon=2.0\times10^{11}\times1.0\times10^{-6}\times1.0\times10^{-3}=200\ \text{N}$, so $m=\dfrac{200}{10}=20\ \text{kg}$.
Answer $20$.

E3. JEE Main · MCQ A uniform rod of weight $W$, length $L$ and cross-sectional area $A$ hangs vertically from a rigid support. If $Y$ is its Young's modulus, the increase in its length due to its own weight is (A) $\dfrac{WL}{AY}$ (B) $\dfrac{WL}{2AY}$ (C) $\dfrac{2WL}{AY}$ (D) $\dfrac{WL}{4AY}$

Idea The tension at height $x$ above the lower end is $Wx/L$, growing from $0$ to $W$; each element $dx$ stretches by $\dfrac{Wx\,dx}{LAY}$.
Integrate $\Delta L=\dfrac{W}{LAY}\displaystyle\int_0^Lx\,dx=\dfrac{WL}{2AY}$.
Answer (B).
⏱ Shortcut The tension varies linearly, so use the average tension $W/2$ in $\Delta L=FL/(AY)$.

E4. JEE Main · Numerical When the pressure on a metal ball is increased by $3.0\times10^8\ \text{Pa}$, its volume decreases by $0.20\%$. The bulk modulus of the metal is $x\times10^{10}\ \text{Pa}$. Find $x$. Give the answer to the nearest integer.

Strain $\dfrac{|\Delta V|}{V}=0.20\%=2.0\times10^{-3}$.
Modulus $B=\dfrac{\Delta p}{|\Delta V|/V}=\dfrac{3.0\times10^8}{2.0\times10^{-3}}=1.5\times10^{11}\ \text{Pa}=15\times10^{10}\ \text{Pa}$.
Answer $15$.
⏱ Shortcut Always convert the percentage to a fraction first; $0.20\%$ is $0.0020$, not $0.20$.

E5. JEE Main · MCQ A block is attached to the lower end of an unstretched vertical wire and released from rest. The wire obeys Hooke's law. The ratio of the greatest extension of the wire during the motion to its extension when the block finally hangs at rest is (A) $1$ (B) $\sqrt2$ (C) $\tfrac12$ (D) $2$

Lowest point The block is momentarily at rest: loss of gravitational energy = elastic energy, $mgx_{\max}=\tfrac12kx_{\max}^2$, so $x_{\max}=\dfrac{2mg}{k}$.
At rest $kx_0=mg$, so $x_0=\dfrac{mg}{k}$, and $\dfrac{x_{\max}}{x_0}=2$.
Answer (D) $2$.
⏱ Shortcut The motion is SHM about $x_0$ starting from rest at $x=0$, so it swings an equal distance $x_0$ beyond: $x_{\max}=2x_0$.

E6. JEE Main · Numerical A light rigid rod $1.2\ \text{m}$ long is suspended horizontally by two vertical wires of equal length attached at its ends: a steel wire ($Y=2.0\times10^{11}\ \text{Pa}$, area $1.5\ \text{mm}^2$) and a copper wire ($Y=1.0\times10^{11}\ \text{Pa}$, area $1.0\ \text{mm}^2$). At what distance, in cm, from the steel wire must a weight be hung so that the rod remains horizontal? Give the answer to the nearest integer.

Equal stretch Rod horizontal $\Rightarrow$ equal extensions $\Rightarrow$ $\dfrac{T_s}{T_c}=\dfrac{Y_sA_s}{Y_cA_c}=\dfrac{2.0\times1.5}{1.0\times1.0}=3$.
Moments About the load point at distance $x$ from the steel end: $T_sx=T_c(1.2-x)$, so $3x=1.2-x$, $x=0.30\ \text{m}=30\ \text{cm}$.
Answer $30$.
⏱ Shortcut The load divides the rod inversely as the stiffnesses: $x=L\,\dfrac{k_c}{k_s+k_c}=1.2\times\dfrac14$. The stiffer wire carries more, so the load sits nearer to it.
🔬 Research–Teaching NexusResearch-tutored · optional, about 45 minutes

Research question. Does a nylon fishing line obey Hooke's law as well as a steel wire does — and does a rubber band obey it at all?

Why it matters. Engineers choose ropes for climbing, mooring lines for ships, tendons for suspension bridges and polymer threads for surgical sutures by their stiffness and by how much energy they absorb and lose. Climbing ropes are deliberately stretchy (low $Y$) so that a falling climber is stopped gently, while lift cables must stretch as little as possible. Biomedical researchers measure the stress–strain curves of tendons, arteries and bone in exactly this way.

What to do.

  1. Hang a $1$–$2\ \text{m}$ length of nylon fishing line from a firm hook, with a light pan at the bottom and a paper marker on the line. Measure its diameter with a screw gauge (or the value printed on the spool).
  2. Add equal loads (bottles of water of known mass) one at a time, recording the marker's position against a metre rule each time; then remove them one by one and record again.
  3. Plot load against extension for loading and unloading. Find $Y$ from the slope of the straight part. Repeat with a rubber band (measure its width and thickness for the area).
  4. Estimate the area between the loading and unloading curves of the rubber band: that is the energy turned into heat per cycle.

Tools: Fishing line, rubber bands, water bottles or a set of masses, metre rule, screw gauge or vernier callipers, spreadsheet for the graphs.

Hand in: The two graphs, your values of $Y$ with an error estimate (Unit 1 rules), and three sentences comparing the materials with steel ($2\times10^{11}\ \text{Pa}$).

Going further. Leave a constant load on the nylon line for an hour and read the marker every ten minutes. Does it keep stretching ("creep")? Why would creep matter for a guitar string, or for the mooring line of a floating platform?

Instructor note: nylon monofilament usually gives $Y$ of the order of $2$–$4\times10^9\ \text{Pa}$, about a hundred times smaller than steel, with a clear straight region and small hysteresis; rubber bands give a curved graph (stiffening at large strain) with a visible hysteresis loop and an effective $Y$ of order $10^6\ \text{Pa}$. The largest error is usually the diameter of the line — students should measure it under load at several points.

🧪 Self-check quiz

0/5 correct

Q1. The dimensional formula of Young's modulus is

Q2. Which of these is the hardest to compress, i.e. has the largest bulk modulus?

Q3. A wire is replaced by another of the same material with twice the length and twice the radius. The Young's modulus of the new wire is

Q4. The elastic potential energy stored per unit volume of a stretched wire, in terms of the stress $\sigma$ and strain $\varepsilon$, is

Q5. A wire is left with a permanent increase in length after a load is removed. This means the load had produced a stress greater than the