Chapter 14 · Electromagnetic Induction and Alternating Currents

14.2 Eddy Currents and Inductance

A changing current induces emfs in nearby metal (eddy currents), in a neighbouring coil (mutual inductance, $\varepsilon_2=-M\,dI_1/dt$) and in its own circuit (self-inductance, $\varepsilon=-L\,dI/dt$). An inductor stores energy $\tfrac12LI^2$ in its magnetic field.

Drop a strong magnet down a copper pipe and it drifts down slowly, as if falling through honey, although copper is not magnetic at all. Put a steel pan on an induction cooktop and the pan gets hot while the glass top stays cool. Switch off a large electric motor and a bright spark jumps across the switch. Hold a phone on a wireless charger and its battery fills with no wire between them. Each of these is electromagnetic induction from Section 14.1 at work, but in a new setting: the changing flux is produced by a current, and the emf appears in a lump of metal, in a second coil, or in the very circuit whose current is changing.

In this section we look first at eddy currents — induced currents that swirl inside solid conductors — with their uses and their nuisances. Then we meet self-inductance, the property that makes a coil resist changes in its own current, and mutual inductance, which couples two coils and is the basis of the transformer. Finally we find the energy stored in an inductor, and see that it lives in the magnetic field itself.

Eddy currents

Faraday's law does not need a wire. Whenever the magnetic flux through any closed path inside a piece of metal changes — because the metal moves through a non-uniform field, or the field through it changes — an emf is induced round that path and a current flows. These currents circulate in closed loops in the bulk of the metal, like eddies (whirlpools) in a stream.

📘 Definition 14.3 — Eddy currents

Eddy currents are induced currents that flow in closed loops inside a bulk conductor when the magnetic flux through it changes. By Lenz's law they always oppose the change that produces them: they oppose the relative motion between the conductor and the field (electromagnetic damping), and they heat the conductor at the rate $I^2R$ summed over all the loops.

Because a block of metal has a very low resistance, even a small induced emf drives a large eddy current, so the forces and the heating can be large. Three classic demonstrations show this.

Uses of eddy currents.

Eddy currents as a nuisance. In the iron cores of transformers, motors and generators the flux changes all the time, and eddy currents waste energy as heat. They are reduced by making the core from thin laminations (sheets) insulated from one another by varnish or oxide, with the sheets lying along the field. The insulating layers cut across the paths in which eddy currents would flow, so each current loop is confined to a thin sheet with a high resistance. Laminating reduces eddy currents greatly; it does not remove them completely.

✏️ Example 1 — Three pipes and a magnet
A small strong magnet of mass $50\ \text{g}$ is dropped from rest down three vertical pipes, each $1.0\ \text{m}$ long: one of plastic, one of copper with a lengthwise slit, and one of solid copper. (a) Put the fall times in order and explain. (b) In the solid copper pipe the magnet very quickly reaches a steady speed of $0.20\ \text{m/s}$. Ignoring the short starting stage, find the time it takes and the heat produced in the pipe, and compare the time with the plastic pipe.
(a) Plastic: no free electrons, no eddy currents, free fall — quickest. Slit copper: the slit breaks the circular current paths round the pipe, so the braking is much weaker. Solid copper: large eddy currents, strong braking — slowest. Order: plastic $\lt$ slit copper $\lt$ solid copper.
(b) Time At constant speed $t=\dfrac{1.0}{0.20}=5.0\ \text{s}$. In the plastic pipe, free fall: $t=\sqrt{\dfrac{2h}{g}}=\sqrt{\dfrac{2.0}{9.8}}=0.45\ \text{s}$ — more than ten times quicker.
(b) Heat At terminal speed the kinetic energy does not change, so all the lost potential energy becomes heat in the pipe: $mgh=0.050\times9.8\times1.0=0.49\ \text{J}$, produced at the rate $mgv=0.098\ \text{W}$.
Note The magnet's weight is balanced by the upward magnetic force from the pipe; by Newton's third law the pipe feels an equal downward force — put the pipe on a balance and it reads heavier while the magnet falls.

In Interactive 1 keep the magnet strength at $1.0$ (in units of the standard magnet) and read the solid copper pipe: terminal speed $0.200\ \text{m/s}$, fall time about $5.0\ \text{s}$. Predict the fall time through the copper pipe when the magnet's strength is doubled.

At strength $2.0$ the copper readouts show a terminal speed of $0.0500\ \text{m/s}$ and a fall time of $20.0\ \text{s}$. Doubling the magnet doubles both the induced emf (twice the flux, changing at the same speed) and the force on the induced current (twice the field), so the braking coefficient grows four times and the terminal speed $v_t=mg/k$ falls to a quarter. In the plastic pipe nothing changes ($0.452\ \text{s}$): no conductor, no eddy currents.
Interactive 1 — Eddy-Current Braking: A Magnet Falling Down Four Pipes

Four identical magnets ($50\ \text{g}$) are dropped together down four $1.0\ \text{m}$ pipes. The eddy currents in a pipe give a braking force proportional to the speed, $kv$, with $k$ set by the pipe's material and growing as the square of the magnet's strength. Press Play (time-lapse) and watch the position–time graphs; choose which pipe the readouts describe.

1.0
terminal speed—
fall time (1.0 m)—
speed at bottom—
heat in pipe—

The iron core of a transformer is built from thin insulated sheets instead of one solid block. The main reason is to

Self-inductance

A coil carrying a current $I$ sets up a magnetic field, and some of that field threads its own turns. If the current changes, its own flux linkage changes, and by Faraday's law an emf is induced in the coil itself. By Lenz's law this emf opposes the change of current: it tries to hold the current back when it is rising and to keep it going when it is falling. It is therefore called a back emf.

With no magnetic material nearby (or an iron core well below saturation), the field — and so the flux linkage — is proportional to the current. The constant of proportionality depends only on the coil's size, shape, number of turns and core.

📘 Definition 14.4 — Self-inductance

The self-inductance $L$ of a coil is the flux linkage per unit current in it:

$$N\Phi_B=LI,\qquad\text{so}\qquad\varepsilon=-\frac{d(N\Phi_B)}{dt}=-L\frac{dI}{dt}.$$

Equivalently, $L$ is the back emf induced per unit rate of change of current. Its SI unit is the henry: $1\ \text{H}=1\ \text{Wb/A}=1\ \text{V s/A}=1\ \Omega\,\text{s}$; dimensions $[\text{ML}^2\text{T}^{-2}\text{A}^{-2}]$. A coil designed to have a large self-inductance is called an inductor.

Self-inductance plays the part of inertia for electric current, just as mass resists changes of velocity: an inductor does not oppose a steady current at all (a steady current in an ideal inductor needs no voltage), but it opposes every change. That is why the current in a circuit containing a large inductor rises gradually when the switch is closed, and why breaking such a circuit suddenly — making $dI/dt$ enormous — produces a large back emf that can make a spark jump across the switch.

Self-inductance of a long solenoid. Take a solenoid of length $l$, cross-sectional area $A$ and $N$ turns, so $n=N/l$ turns per metre, with $l$ much larger than its radius. Inside it the field is uniform, $B=\mu_0nI$ (Ampère's law, Chapter 13), and the flux through each turn is $BA$. The flux linkage is

$$N\Phi_B=(nl)(\mu_0nI)A=\mu_0n^2AlI,\qquad\text{so}\qquad L=\mu_0n^2Al=\frac{\mu_0N^2A}{l}.$$
📐 Result 14.7 — Inductance of a long solenoid

A long solenoid of length $l$, cross-sectional area $A$ and $N$ turns ($n=N/l$ per metre), with end effects neglected, has

$$L=\mu_0n^2Al=\frac{\mu_0N^2A}{l}.$$

Filled with a core of relative permeability $\mu_r$, $L=\mu_r\mu_0n^2Al$. $L$ depends only on the geometry and the core — not on the current — and grows as the square of the number of turns. Inductors far apart (no shared flux) combine like resistors: $L=L_1+L_2$ in series, $\dfrac1L=\dfrac1{L_1}+\dfrac1{L_2}$ in parallel.

Potential difference across an inductor. In circuit problems treat an inductor like a cell whose emf is $-L\,dI/dt$. Going through an inductor in the direction of the current, the potential falls by $L\,\dfrac{dI}{dt}$ (plus $IR$ if the coil has resistance $R$). If the current is decreasing, $dI/dt$ is negative and the potential rises: the inductor then acts as a source, pushing the current onward.

🧭 Problem-solving strategy — Potential difference along a branch with an inductor
  1. Mark the direction of the current and whether it is increasing or decreasing; write $dI/dt$ with its sign.
  2. Walk from one end of the branch to the other in the direction of the current, adding up the changes of potential: $-IR$ across a resistor, $+\varepsilon$ across a cell from its negative to its positive terminal ($-\varepsilon$ the other way), $-L\,dI/dt$ across an inductor.
  3. The sum is $V_\text{end}-V_\text{start}$.
✏️ Example 2 — An air-core coil and an iron-core coil
A solenoid has $500$ turns wound over a length of $25\ \text{cm}$ on a tube of cross-sectional area $4.0\ \text{cm}^2$. (a) Find its self-inductance. (b) A current of $2.0\ \text{A}$ in it is switched off and falls uniformly to zero in $5.0\ \text{ms}$. Find the back emf. (c) Repeat (a) and (b) when the tube is filled with soft iron of relative permeability $800$. (d) What would the air-core inductance be with $1000$ turns on the same length?
(a) $L=\dfrac{\mu_0N^2A}{l}=\dfrac{4\pi\times10^{-7}\times500^2\times4.0\times10^{-4}}{0.25}=5.03\times10^{-4}\ \text{H}=0.503\ \text{mH}$.
(b) $\left|\dfrac{dI}{dt}\right|=\dfrac{2.0}{5.0\times10^{-3}}=400\ \text{A/s}$; $|\varepsilon|=L\left|\dfrac{dI}{dt}\right|=5.03\times10^{-4}\times400=0.201\ \text{V}$.
(c) $L=800\times0.503\ \text{mH}=0.402\ \text{H}$ and $|\varepsilon|=0.402\times400=161\ \text{V}$ — from a $2\ \text{A}$ circuit. This is why inductive circuits spark when broken.
(d) $L\propto N^2$: four times as much, $2.01\ \text{mH}$.
✏️ Example 3 — Potential difference along a branch
A branch of a circuit runs from point A to point B through, in order, a $2.0\ \Omega$ resistor, a $10\ \text{V}$ cell of negligible internal resistance with its positive terminal towards B, and an ideal $4.0\ \text{mH}$ inductor. At one instant a current of $3.0\ \text{A}$ flows from A to B and is decreasing at $500\ \text{A/s}$. Find $V_B-V_A$ at that instant. What would it be if the current were increasing at $500\ \text{A/s}$?
Find $V_B-V_A$ for the decreasing current before you open the solution:
Resistor Along the current: $-IR=-3.0\times2.0=-6.0\ \text{V}$.
Cell From its negative to its positive terminal: $+10\ \text{V}$.
Inductor $-L\dfrac{dI}{dt}=-4.0\times10^{-3}\times(-500)=+2.0\ \text{V}$: the decreasing current makes the inductor push the current on, a rise of potential.
Total $V_B-V_A=-6.0+10+2.0=6.0\ \text{V}$. If the current were increasing, the inductor term would be $-2.0\ \text{V}$ and $V_B-V_A=2.0\ \text{V}$.
⏱ Shortcut Write one line, $V_A-IR+\varepsilon-L\dfrac{dI}{dt}=V_B$, and substitute signed values. The commonest slip is to use $|dI/dt|$ and get $2.0\ \text{V}$ for the decreasing case.

A long air-core solenoid has self-inductance $L$. It is rewound with twice as many turns on the same length and the same tube. Its self-inductance becomes

Mutual inductance

Place two coils near each other. A current $I_1$ in coil 1 sends some of its field through coil 2, giving coil 2 a flux linkage $N_2\Phi_{21}$ proportional to $I_1$. If $I_1$ changes, an emf is induced in coil 2 — although nothing connects the two circuits. This is Faraday's original experiment, and it is how transformers, wireless chargers and the ignition coil of a petrol engine work.

📘 Definition 14.5 — Mutual inductance

The mutual inductance $M$ of a pair of coils is the flux linkage of one coil per unit current in the other:

$$N_2\Phi_{21}=MI_1,\qquad\text{so}\qquad\varepsilon_2=-M\frac{dI_1}{dt}.$$

Its unit is the henry. $M$ depends on the shapes, sizes and numbers of turns of the coils, on their separation and relative orientation, and on any core between them — not on the currents.

A remarkable fact makes $M$ a property of the pair: the flux linkage of coil 2 per unit current in coil 1 always equals the flux linkage of coil 1 per unit current in coil 2, $M_{21}=M_{12}=M$, however different the coils are. We can check it for the most important case.

Two coaxial solenoids. A long solenoid $S_1$ (radius $r_1$, $n_1$ turns per metre) lies inside a longer solenoid $S_2$ (radius $r_2\gt r_1$, $n_2$ turns per metre), both of length $l$. (i) A current $I_2$ in the outer solenoid gives a field $\mu_0n_2I_2$ everywhere inside it, so the flux linkage of the inner coil is $(n_1l)(\mu_0n_2I_2)(\pi r_1^2)$: $M_{12}=\mu_0n_1n_2\pi r_1^2l$. (ii) A current $I_1$ in the inner solenoid gives a field $\mu_0n_1I_1$ inside it and (almost) zero outside it, so although the outer turns enclose a larger area, the flux through each is only $\mu_0n_1I_1\pi r_1^2$. Its flux linkage is $(n_2l)(\mu_0n_1I_1)(\pi r_1^2)$: $M_{21}=\mu_0n_1n_2\pi r_1^2l$ — the same.

📐 Result 14.8 — Mutual inductance

(i) Reciprocity: $M_{12}=M_{21}=M$. The emf induced in either coil by a given rate of change of current in the other is the same.

(ii) Coaxial long solenoids of common length $l$, the inner of radius $r_1$:

$$M=\mu_0n_1n_2\pi r_1^2\,l\qquad(\text{the smaller, inner area}),$$

multiplied by $\mu_r$ if a core of relative permeability $\mu_r$ fills the inner solenoid.

(iii) Coupling: for any two coils $M=k\sqrt{L_1L_2}$ with $0\le k\le1$; $k=1$ (perfect coupling) only when every line of flux of each coil threads all the turns of the other. Hence $M\le\sqrt{L_1L_2}$.

Another useful pair: a small loop of radius $r$ at the centre of a large coplanar loop of radius $R\gg r$. A current $I$ in the large loop gives a field $\dfrac{\mu_0I}{2R}$ at its centre (Biot–Savart law, Chapter 13), nearly uniform over the small loop, so $M=\dfrac{\mu_0\pi r^2}{2R}$. Computing it the other way — the flux of the small loop's dipole field through the large loop — is hard, but reciprocity guarantees the same answer.

✏️ Example 4 — Coaxial solenoids
An inner solenoid of radius $1.0\ \text{cm}$ with $2000$ turns per metre lies coaxially inside an outer solenoid of radius $2.0\ \text{cm}$ with $1000$ turns per metre; both are $50\ \text{cm}$ long. (a) Find their mutual inductance. (b) The current in the inner solenoid rises at $50\ \text{A/s}$. Find the emf induced in the outer one. (c) Find the self-inductance of each solenoid and the coupling coefficient $k$.
Find $M$ in (a) before you open the solution:
(a) $M=\mu_0n_1n_2\pi r_1^2l=4\pi\times10^{-7}\times2000\times1000\times\pi\times(0.010)^2\times0.50=3.95\times10^{-4}\ \text{H}=0.395\ \text{mH}$.
(b) $|\varepsilon_2|=M\dfrac{dI_1}{dt}=3.95\times10^{-4}\times50=1.97\times10^{-2}\ \text{V}=19.7\ \text{mV}$.
(c) $L_1=\mu_0n_1^2\pi r_1^2l=4\pi\times10^{-7}\times4\times10^6\times\pi\times10^{-4}\times0.50=0.790\ \text{mH}$; $L_2=\mu_0n_2^2\pi r_2^2l=4\pi\times10^{-7}\times10^6\times\pi\times4\times10^{-4}\times0.50=0.790\ \text{mH}$. $k=\dfrac{M}{\sqrt{L_1L_2}}=\dfrac{0.395}{0.790}=0.50$.
Check In general here $k=\dfrac{n_1n_2r_1^2}{\sqrt{n_1^2r_1^2\,n_2^2r_2^2}}=\dfrac{r_1}{r_2}=0.50$ ✓: only the part of the outer coil's flux that passes through the inner coil is shared.
✏️ Example 5 — A small loop inside a large one
A small circular loop of radius $1.0\ \text{cm}$ lies at the centre of a large circular loop of radius $20\ \text{cm}$, in the same plane. (a) Find their mutual inductance. (b) The current in the large loop falls uniformly from $10\ \text{A}$ to zero in $0.10\ \text{s}$. Find the emf induced in the small loop. (c) Without any new calculation, find the flux through the large loop when a current of $2.0\ \text{A}$ flows in the small loop. (d) Find $M$ if the small loop is tilted so that its plane makes $60^\circ$ with the plane of the large loop.
(a) $M=\dfrac{\mu_0\pi r^2}{2R}=\dfrac{4\pi\times10^{-7}\times\pi\times(0.010)^2}{2\times0.20}=9.87\times10^{-10}\ \text{H}$.
(b) $\dfrac{dI}{dt}=100\ \text{A/s}$; $|\varepsilon|=9.87\times10^{-10}\times100=9.87\times10^{-8}\ \text{V}$ — tiny, because the small loop catches very little flux.
(c) By reciprocity, $\Phi=MI=9.87\times10^{-10}\times2.0=1.97\times10^{-9}\ \text{Wb}$ — a result that would need a hard integration of the dipole field over the large loop.
(d) The angle between the field (normal to the big loop) and the small loop's normal is now $60^\circ$: $M=9.87\times10^{-10}\times\cos60^\circ=4.93\times10^{-10}\ \text{H}$.

For two coaxial long solenoids of equal length, the inner of radius $r_1$ and the outer of radius $r_2$, the mutual inductance depends on

Energy stored in an inductor

To set up a current in an inductor, the source must push charge against the back emf. When the current is $I$ and rising at $dI/dt$, the back emf is $L\,dI/dt$, and the source does work against it at the rate

$$P=\left(L\frac{dI}{dt}\right)I,\qquad\text{so}\qquad dW=LI\,dI.$$

Building the current up from $0$ to $I$ needs $W=\displaystyle\int_0^ILI\,dI=\tfrac12LI^2$. This work is not lost as heat: it is stored, and when the current falls the inductor gives it back (that is the energy in the spark when an inductive circuit is broken).

📐 Result 14.9 — Energy stored in an inductor

An inductor of self-inductance $L$ carrying a current $I$ stores energy

$$U=\tfrac12LI^2=\frac{(N\Phi_B)^2}{2L}=\tfrac12(N\Phi_B)I.$$

The energy depends on the current, not on how fast it is changing; it is the magnetic counterpart of $\tfrac12CV^2$ for a capacitor and of $\tfrac12mv^2$ for a moving body ($L$ plays the part of mass, $I$ of velocity).

Where is the energy? For a long solenoid, $L=\mu_0n^2Al$ and $B=\mu_0nI$, so

$$U=\tfrac12\mu_0n^2AlI^2=\frac{(\mu_0nI)^2}{2\mu_0}\,(Al)=\frac{B^2}{2\mu_0}\times\text{volume}.$$

The energy is spread through the space where the field is, with the same amount in every cubic metre. Although derived for a solenoid, this result holds for any magnetic field in vacuum (or air).

📐 Result 14.10 — Energy density of a magnetic field

A magnetic field $B$ in vacuum (or air) stores energy per unit volume

$$u_B=\frac{B^2}{2\mu_0},$$

in $\text{J/m}^3$ — the magnetic counterpart of $u_E=\tfrac12\varepsilon_0E^2$.

✏️ Example 6 — Energy in a solenoid, two ways
A long air-core solenoid of length $50\ \text{cm}$ and radius $2.0\ \text{cm}$ has $1000$ turns and carries a current of $4.0\ \text{A}$. (a) Find its self-inductance and the energy stored. (b) Find the field inside it and the energy density, and check (a). (c) At an instant when the current is $4.0\ \text{A}$ and increasing at $50\ \text{A/s}$, at what rate is energy being stored? (d) How much energy is stored if the current is doubled?
Find the energy stored in (a) before you open the solution:
(a) $A=\pi(0.020)^2=1.257\times10^{-3}\ \text{m}^2$; $L=\dfrac{4\pi\times10^{-7}\times10^6\times1.257\times10^{-3}}{0.50}=3.16\times10^{-3}\ \text{H}$. $U=\tfrac12LI^2=\tfrac12\times3.16\times10^{-3}\times16=2.53\times10^{-2}\ \text{J}=25.3\ \text{mJ}$.
(b) $B=\mu_0nI=4\pi\times10^{-7}\times2000\times4.0=1.01\times10^{-2}\ \text{T}$. $u_B=\dfrac{B^2}{2\mu_0}=\dfrac{(1.005\times10^{-2})^2}{2\times4\pi\times10^{-7}}=40.2\ \text{J/m}^3$. Volume $Al=6.28\times10^{-4}\ \text{m}^3$, so $U=40.2\times6.28\times10^{-4}=25.3\ \text{mJ}$ ✓.
(c) $\dfrac{dU}{dt}=LI\dfrac{dI}{dt}=3.16\times10^{-3}\times4.0\times50=0.632\ \text{W}$.
(d) $U\propto I^2$: four times as much, $101\ \text{mJ}$.

In Interactive 2 set $N=500$, $l=25\ \text{cm}$, $A=4.0\ \text{cm}^2$, air core: $L=0.503\ \text{mH}$, peak stored energy $1.01\ \text{mJ}$ and a back emf of $0.201\ \text{V}$ while the current falls. Predict the peak stored energy when you double the turns to $N=1000$.

With $N=1000$ the readouts show $L=2.01\ \text{mH}$ and a peak energy of $4.02\ \text{mJ}$: $L\propto N^2$ quadruples, and with the same $2.0\ \text{A}$ peak current $U=\tfrac12LI^2$ quadruples too. Both back emfs also quadruple ($0.402\ \text{V}$ during the $10\ \text{ms}$ rise, $0.804\ \text{V}$ during the $5\ \text{ms}$ fall). Notice that the back emf is zero while the current is steady, even though that is when the stored energy is largest.
Interactive 2 — Build an Inductor: Back EMF and Stored Energy

Design a solenoid — turns $N$, length $l$, cross-section $A$, core — and drive it with a current that rises from $0$ to $2.0\ \text{A}$ in $10\ \text{ms}$, stays steady for $10\ \text{ms}$, then falls to zero in $5\ \text{ms}$. Press Play to sweep through the cycle: the graphs show the current, the back emf $-L\,dI/dt$ and the stored energy $\tfrac12LI^2$.

50025 cm4.0 cm²
inductance $L$—
back emf (rise / fall)—
peak energy—
now: $I$, $U$—
🚀 Beyond JEE Main (JEE Advanced) — growth and decay of current in an LR circuit

LR circuits are not named in the JEE Main 2026 syllabus list (they are listed for JEE Advanced 2026). This box is for interest only; nothing here is used in the exercises, the Exam corner or the quiz.

Connect an inductor $L$ in series with a resistance $R$ to a cell of emf $\varepsilon$. Kirchhoff's loop rule gives $\varepsilon-L\dfrac{dI}{dt}-IR=0$, and the current grows smoothly towards $\varepsilon/R$:

$$I=\frac{\varepsilon}{R}\left(1-e^{-t/\tau}\right),\qquad\tau=\frac LR.$$

After one time constant $\tau$ the current has reached $63\%$ of its final value. If the cell is then removed and the coil is shorted through $R$, the current decays as $I=I_0e^{-t/\tau}$, and the stored energy $\tfrac12LI_0^2$ ends up as heat in $R$. The equations have exactly the same form as those of the rod on rails in Section 14.1, with $L$ in place of $m$.

⚠️ JEE Main traps

1. $L$ is a property of the coil, not of the current. $L=N\Phi_B/I$ is constant for a given coil and core; doubling the current doubles the flux, not $L$. A steady current produces no back emf, however large $L$ is.

2. $N^2$, and $n$ versus $N$. $L=\mu_0N^2A/l=\mu_0n^2Al$ — mixing the two (e.g. $\mu_0n^2A/l$) is the usual slip. Twice the turns on the same length gives $4L$; twice the turns and twice the length (same $n$) gives $2L$.

3. Coaxial solenoids use the inner area. $M=\mu_0n_1n_2\pi r_1^2l$, the same whichever coil carries the current. And $M\le\sqrt{L_1L_2}$ always.

4. Signs along a branch. Through an inductor in the direction of the current the potential changes by $-L\,dI/dt$ with the signed $dI/dt$: a decreasing current makes the inductor raise the potential.

5. Energy depends on $I$, not on $dI/dt$. $U=\tfrac12LI^2$ is largest when the current is largest, even if the back emf is then zero. And laminating a core reduces eddy-current loss; it does not stop the flux or remove eddy currents completely.

The current through an inductor is doubled. The energy stored in it

Exercises

Take $\mu_0=4\pi\times10^{-7}\ \text{T m/A}$ and $g=9.8\ \text{m/s}^2$. Solenoids are long and air-cored unless told otherwise; end effects are neglected.

I
Eddy currents.
  • 1 A solid copper plate swinging between the poles of a magnet stops quickly, but a plate with deep slots cut in it swings for a long time. Explain.
  • 2 Why is a transformer core made of thin insulated sheets, and why must the sheets lie along the magnetic field rather than across it?
  • 3 Why does an induction cooktop heat a steel pan but not a glass dish? Where is the heat produced?
  • 4 A magnet of mass $40\ \text{g}$ falls through a vertical copper pipe $1.5\ \text{m}$ long at a steady $0.25\ \text{m/s}$. Find the time taken and the heat produced in the pipe.
  • 5 An eddy-current brake slows a $2.0\times10^5\ \text{kg}$ train on level track from $20\ \text{m/s}$ to $5.0\ \text{m/s}$. How much heat is produced (ignore other losses)? Why can such a brake not hold the train at rest?
  • 6 Why is the coil of a moving-coil galvanometer wound on a metal frame?
  • 7 A copper disc spins freely on an axle. When a magnet is brought close to its rim, it slows down. Where does its kinetic energy go?
1 In the solid plate large eddy-current loops form; the field pushes on them against the motion (Lenz's law). The slots break the loops into long narrow paths of high resistance, so the eddy currents and the damping are much smaller.
2 To reduce eddy currents and the heat they waste. The eddy currents circulate in planes perpendicular to the field; insulating layers lying along the field cut across those paths. Sheets across the field would leave the current loops intact.
3 The coil's rapidly alternating field induces eddy currents only in a conductor; steel conducts (and its iron concentrates the flux), glass has no free electrons. The heat is produced in the base of the pan itself; the cooktop warms only by contact with the pan.
4 $t=\dfrac{1.5}{0.25}=6.0\ \text{s}$; heat $=mgh=0.040\times9.8\times1.5=0.588\ \text{J}$.
5 Heat $=\tfrac12m(v_1^2-v_2^2)=\tfrac12\times2.0\times10^5\times(400-25)=3.75\times10^7\ \text{J}$. The braking force is proportional to the speed, so it vanishes as the train stops: a friction brake is needed to hold it.
6 As the coil swings, eddy currents induced in the metal frame oppose its motion, so the pointer settles quickly at its reading without oscillating (electromagnetic damping, a "dead-beat" movement).
7 The moving metal cuts the magnet's field and eddy currents flow in the disc; the force on them opposes the rotation, and the kinetic energy becomes heat ($I^2R$) in the disc.
II
Self-inductance.
  • 1 Find the self-inductance of a solenoid of $800$ turns, length $40\ \text{cm}$ and cross-sectional area $5.0\ \text{cm}^2$, in mH.
  • 2 A current of $2.0\ \text{A}$ in a $200$-turn coil produces a flux of $5.0\times10^{-4}\ \text{Wb}$ through each turn. Find its self-inductance.
  • 3 The current in a $0.30\ \text{H}$ coil falls steadily from $4.0\ \text{A}$ to $1.0\ \text{A}$ in $0.050\ \text{s}$. Find the induced emf.
  • 4 The current in a $20\ \text{mH}$ inductor is $I=(3t^2+2t)\ \text{A}$, with $t$ in seconds. Find the back emf at $t=2.0\ \text{s}$.
  • 5 The solenoid of part 1 is extended to twice the length with twice the number of turns (same turns per metre and area). Find its new self-inductance.
  • 6 Inductors of $4.0\ \text{mH}$ and $6.0\ \text{mH}$, far apart, are connected (a) in series and (b) in parallel. Find the combined inductance in each case.
  • 7 A branch runs from A to B through a $5.0\ \Omega$ resistor and an ideal $10\ \text{mH}$ inductor. A current of $2.0\ \text{A}$ flows from A to B and is increasing at $100\ \text{A/s}$. Find $V_A-V_B$. What is it if the current is decreasing at the same rate?
  • 8 Explain why a spark often appears at a switch when a circuit containing a large inductor is opened, but not when it is closed.
1 $L=\dfrac{\mu_0N^2A}{l}=\dfrac{4\pi\times10^{-7}\times6.4\times10^5\times5.0\times10^{-4}}{0.40}=1.01\times10^{-3}\ \text{H}=1.01\ \text{mH}$.
2 $L=\dfrac{N\Phi_B}{I}=\dfrac{200\times5.0\times10^{-4}}{2.0}=0.050\ \text{H}$.
3 $|\varepsilon|=L\left|\dfrac{\Delta I}{\Delta t}\right|=0.30\times\dfrac{3.0}{0.050}=18\ \text{V}$ (in the direction that tries to keep the current flowing).
4 $\dfrac{dI}{dt}=6t+2=14\ \text{A/s}$; $|\varepsilon|=0.020\times14=0.28\ \text{V}$.
5 $L=\mu_0n^2Al\propto l$ at fixed $n$: $2\times1.01=2.01\ \text{mH}$. (Doubling $N$ alone on the same length would give $4L$.)
6 (a) $4.0+6.0=10\ \text{mH}$; (b) $\dfrac{4.0\times6.0}{10}=2.4\ \text{mH}$.
7 $V_A-V_B=IR+L\dfrac{dI}{dt}=10+0.010\times100=11\ \text{V}$. Decreasing: $10-1.0=9.0\ \text{V}$.
8 Opening the switch forces the current to zero in a tiny time, so $L\,|dI/dt|$ — the back emf — is very large and can ionise the air across the opening contacts; the stored energy $\tfrac12LI^2$ goes into the spark. On closing, the back emf only slows the rise of current and never exceeds the supply emf.
III
Mutual inductance.
  • 1 When the current in coil A changes at $40\ \text{A/s}$, an emf of $0.20\ \text{V}$ is induced in coil B. Find their mutual inductance, in mH.
  • 2 For the pair of part 1, the current in B rises steadily from $0$ to $3.0\ \text{A}$ in $0.010\ \text{s}$. Find the emf induced in A.
  • 3 A long solenoid with $1500$ turns per metre and cross-sectional area $10\ \text{cm}^2$ has a $50$-turn coil wound tightly round its middle. Find their mutual inductance, in μH.
  • 4 The current in the solenoid of part 3 falls uniformly from $3.0\ \text{A}$ to zero in $2.0\ \text{ms}$. Find the emf induced in the small coil.
  • 5 Two coils have $L_1=0.20\ \text{H}$, $L_2=0.80\ \text{H}$ and $M=0.30\ \text{H}$. Find the coupling coefficient.
  • 6 What is the largest possible mutual inductance of two coils of self-inductances $9.0\ \text{mH}$ and $4.0\ \text{mH}$?
  • 7 A current of $2.0\ \text{A}$ in coil 1 produces a flux of $2.0\times10^{-5}\ \text{Wb}$ through each of the $400$ turns of coil 2. Find $M$, and the flux linkage of coil 1 when instead $2.0\ \text{A}$ flows in coil 2.
  • 8 A loop of radius $2.0\ \text{cm}$ lies at the centre of a coplanar loop of radius $50\ \text{cm}$. Find their mutual inductance.
1 $M=\dfrac{|\varepsilon_B|}{dI_A/dt}=\dfrac{0.20}{40}=5.0\times10^{-3}\ \text{H}=5.0\ \text{mH}$.
2 Same $M$ both ways: $|\varepsilon_A|=5.0\times10^{-3}\times\dfrac{3.0}{0.010}=1.5\ \text{V}$.
3 $M=\mu_0nNA=4\pi\times10^{-7}\times1500\times50\times1.0\times10^{-3}=9.42\times10^{-5}\ \text{H}=94.2\ \mu\text{H}$.
4 $\dfrac{dI}{dt}=1500\ \text{A/s}$; $|\varepsilon|=9.42\times10^{-5}\times1500=0.141\ \text{V}$.
5 $k=\dfrac{M}{\sqrt{L_1L_2}}=\dfrac{0.30}{\sqrt{0.16}}=0.75$.
6 $M_\text{max}=\sqrt{L_1L_2}=\sqrt{36}=6.0\ \text{mH}$ (perfect coupling, $k=1$).
7 $M=\dfrac{N_2\Phi_{21}}{I_1}=\dfrac{400\times2.0\times10^{-5}}{2.0}=4.0\times10^{-3}\ \text{H}$. By reciprocity the flux linkage of coil 1 is $MI_2=8.0\times10^{-3}\ \text{Wb}$.
8 $M=\dfrac{\mu_0\pi r^2}{2R}=\dfrac{4\pi\times10^{-7}\times\pi\times4.0\times10^{-4}}{1.0}=1.58\times10^{-9}\ \text{H}$.
IV
Energy in inductors and harder problems.
  • 1 Find the energy stored in a $0.20\ \text{H}$ inductor carrying $3.0\ \text{A}$.
  • 2 A coil stores $25\ \text{mJ}$ when it carries $0.50\ \text{A}$. Find its self-inductance.
  • 3 Find the energy density of a magnetic field of $0.50\ \text{T}$ in air.
  • 4 The current in a $50\ \text{mH}$ coil rises from $2.0\ \text{A}$ to $6.0\ \text{A}$. Find the increase in stored energy.
  • 5 A solenoid with $2000$ turns per metre, cross-sectional area $2.0\ \text{cm}^2$ and length $30\ \text{cm}$ carries $3.0\ \text{A}$. Find the field inside, the energy density and the total energy stored, in mJ.
  • 6 At an instant when the current in a $0.40\ \text{H}$ inductor is $2.0\ \text{A}$ and increasing at $5.0\ \text{A/s}$, at what rate is energy being stored in it?
  • 7 The solenoid of part 5 is filled with a core of relative permeability $400$ (assume no saturation) and carries the same current. Find the energy stored.
  • 8 A fixed length of wire is wound into a long solenoid of a given length. It is unwound and rewound on the same length but on a tube of half the radius. Show that the self-inductance does not change.
1 $U=\tfrac12LI^2=\tfrac12\times0.20\times9.0=0.90\ \text{J}$.
2 $L=\dfrac{2U}{I^2}=\dfrac{0.050}{0.25}=0.20\ \text{H}$.
3 $u_B=\dfrac{B^2}{2\mu_0}=\dfrac{0.25}{2\times4\pi\times10^{-7}}=9.95\times10^4\ \text{J/m}^3$.
4 $\Delta U=\tfrac12\times0.050\times(36-4.0)=0.80\ \text{J}$.
5 $B=\mu_0nI=4\pi\times10^{-7}\times2000\times3.0=7.54\times10^{-3}\ \text{T}$; $u_B=\dfrac{B^2}{2\mu_0}=22.6\ \text{J/m}^3$; volume $=2.0\times10^{-4}\times0.30=6.0\times10^{-5}\ \text{m}^3$, so $U=1.36\times10^{-3}\ \text{J}=1.36\ \text{mJ}$. (Check: $L=\mu_0n^2Al=3.02\times10^{-4}\ \text{H}$, $\tfrac12LI^2=1.36\ \text{mJ}$ ✓.)
6 $\dfrac{dU}{dt}=LI\dfrac{dI}{dt}=0.40\times2.0\times5.0=4.0\ \text{W}$.
7 $L$ and hence $U$ grow by the factor $\mu_r$: $U=400\times1.36\ \text{mJ}=0.543\ \text{J}$.
8 The wire length is $N\times2\pi r$, so halving $r$ doubles $N$. $L=\mu_0N^2\pi r^2/l\propto(Nr)^2$, and $Nr$ is fixed by the wire length: $L$ is unchanged.
🎯 Exam corner JEE Main · MCQJEE Main · Numerical

E1. JEE Main · MCQ A long air-core solenoid has self-inductance $L$. Another solenoid of the same cross-section has twice the number of turns and half the length. Its self-inductance is (A) $2L$ (B) $4L$ (C) $8L$ (D) $L/2$

Formula $L=\dfrac{\mu_0N^2A}{l}\propto\dfrac{N^2}{l}$.
Ratio $\dfrac{2^2}{1/2}=8$.
Answer (C).
⏱ Shortcut (B) forgets the length; (A) forgets that $L\propto N^2$. In terms of $n=N/l$: $n$ goes up 4 times, $L=\mu_0n^2Al$ goes up $16\times\tfrac12=8$ times ✓.

E2. JEE Main · Numerical When the current in a coil rises steadily from $2.0\ \text{A}$ to $4.0\ \text{A}$ in $0.050\ \text{s}$, the back emf is $8.0\ \text{V}$. Find the energy, in mJ, stored in the coil when the current is $4.0\ \text{A}$. Give the answer to the nearest integer.

Inductance $L=\dfrac{|\varepsilon|}{dI/dt}=\dfrac{8.0}{2.0/0.050}=\dfrac{8.0}{40}=0.20\ \text{H}$.
Energy $U=\tfrac12LI^2=\tfrac12\times0.20\times16=1.6\ \text{J}=1600\ \text{mJ}$.
Answer $1600$.
⏱ Shortcut The energy depends on the present current only, not on how fast it is changing — the $8.0\ \text{V}$ is needed only to find $L$.

E3. JEE Main · MCQ A branch of a circuit runs from A to B through a $3.0\ \Omega$ resistor, then a $12\ \text{V}$ cell (negligible internal resistance) with its positive terminal towards B, then an ideal $2.0\ \text{mH}$ inductor. A current of $2.0\ \text{A}$ flows from A to B and is increasing at $2000\ \text{A/s}$. Then $V_A-V_B$ is (A) $-2.0\ \text{V}$ (B) $22\ \text{V}$ (C) $2.0\ \text{V}$ (D) $-10\ \text{V}$

Walk A → B $V_B=V_A-IR+\varepsilon-L\dfrac{dI}{dt}=V_A-6.0+12-2.0\times10^{-3}\times2000=V_A+2.0\ \text{V}$.
Result $V_A-V_B=-2.0\ \text{V}$.
Answer (A).
⏱ Shortcut (C) has the right size but the wrong sign — decide whether you want $V_A-V_B$ or $V_B-V_A$ before you write the line. (D) is the answer for a current decreasing at $2000\ \text{A/s}$, when the inductor term becomes $+4.0\ \text{V}$.

E4. JEE Main · Numerical A solenoid of radius $1.0\ \text{cm}$ with $2000$ turns per metre lies coaxially inside a solenoid of radius $3.0\ \text{cm}$ with $500$ turns per metre; both are $1.0\ \text{m}$ long. Find their mutual inductance in μH. (Take $\mu_0=4\pi\times10^{-7}\ \text{T m/A}$ and $\pi^2=10$.) Give the answer to the nearest integer.

Formula $M=\mu_0n_1n_2\pi r_1^2l$ with the inner radius $1.0\ \text{cm}$.
Numbers $M=4\pi^2\times10^{-7}\times2000\times500\times10^{-4}\times1.0=40\times10^{-7}\times10^{2}=4.0\times10^{-4}\ \text{H}=400\ \mu\text{H}$.
Answer $400$.
⏱ Shortcut Using the outer radius would give $9\times400=3600$ — the trap. The outer coil's size never enters.

E5. JEE Main · MCQ Which of the following does not depend on eddy currents? (A) an induction furnace melting steel (B) electromagnetic braking of a train (C) dead-beat damping of a moving-coil galvanometer (D) the heating element of an electric kettle

Check each (A) heat from eddy currents induced by a high-frequency field; (B) eddy currents in a disc or rail oppose the motion; (C) eddy currents in the coil's metal frame damp its swing.
(D) A kettle element is an ordinary resistor heated by the current the supply drives through it (Joule heating) — no induction involved.
Answer (D).
⏱ Shortcut Eddy currents need a changing flux through bulk metal. Ask "where is the changing field?" — in (D) there is none that matters.

E6. JEE Main · Numerical A $2.0\ \text{H}$ inductor carries a current of $3.0\ \text{A}$. The current is reduced to $1.0\ \text{A}$ in $0.20\ \text{s}$. Find the average rate, in watts, at which the inductor gives up its stored energy during this time. Give the answer to the nearest integer.

Energy released $\Delta U=\tfrac12L\left(I_1^2-I_2^2\right)=\tfrac12\times2.0\times(9.0-1.0)=8.0\ \text{J}$.
Rate $\bar P=\dfrac{8.0}{0.20}=40\ \text{W}$.
Answer $40$.
⏱ Shortcut $\tfrac12L(I_1-I_2)^2=4.0\ \text{J}$ (giving $20$) is the classic slip: subtract the squares, not the currents.
🔬 Research–Teaching NexusResearch-tutored · optional, about 45 minutes

Research question. How does the braking of a magnet falling down a metal pipe depend on the pipe's material and wall thickness — and does the terminal speed follow $v_t=mg/k$ with $k$ proportional to the metal's conductivity?

Why it matters. Eddy-current brakes stop roller-coasters at theme parks around the world, slow high-speed trains in Germany and Japan without touching the rail, and control the resistance of exercise bikes. Their designers must predict the braking force from the conductor's material and shape. The same physics limits how much energy is lost in transformer cores across every national grid. A magnet and a few pipes reproduce the whole story on a desk.

What to do.

  1. Collect pipes of the same length (about $1\ \text{m}$) and similar bore: copper, aluminium, brass and plastic; if possible copper pipes of two wall thicknesses, and one copper pipe with a lengthwise saw-cut.
  2. Choose a neodymium magnet that slides freely in the pipes. Measure its mass.
  3. Drop it through each pipe five times and time the fall with a stopwatch or a phone video. Find the average time and the terminal speed $v_t\approx\text{length}/\text{time}$.
  4. Compute $k=mg/v_t$ for each pipe. Look up the electrical conductivity of each metal and plot $k$ against conductivity.
  5. Compare the solid and the slit copper pipes, and the thin and thick walls.

Tools: Metal and plastic pipes, a strong magnet, stopwatch or phone camera, metre rule, balance, conductivity table, spreadsheet.

Hand in: A results table with uncertainties, the graph of $k$ against conductivity, and a paragraph explaining the effects of the slit and of wall thickness in terms of the paths and resistance of the eddy currents.

Going further. Stand the pipe on a kitchen scale and film the reading while the magnet falls. Explain the extra reading using Newton's third law and compare it with $mg$. Compare with Interactive 1, which uses the same model.

Instructor note: $k$ is roughly proportional to conductivity and to wall thickness (for thin walls), so copper brakes more than aluminium, which brakes more than brass; the slit copper pipe gives a much smaller $k$. Plastic gives free fall (about $0.45\ \text{s}$ for $1\ \text{m}$), useful as a timing check. The scale reading rises by about $mg$ while the magnet falls at terminal speed — a striking demonstration that the braking force is a real interaction between magnet and pipe.

🧪 Self-check quiz

0/5 correct

Q1. The henry is equivalent to

Q2. The self-inductance of a long solenoid of fixed length and cross-section is proportional to

Q3. Eddy-current losses in the core of a transformer are reduced by

Q4. The energy stored in an inductor carrying current $I$ is $U$. The flux linkage of the inductor is

Q5. Two coils have self-inductances $16\ \text{mH}$ and $4.0\ \text{mH}$. Their mutual inductance cannot be