Chapter 19 · Electronic Devices

19.2 Diode Circuits and Special-Purpose Diodes

Treat the diode as a one-way switch with a $0.7\ \text{V}$ toll and whole circuits become easy. Then put it to work: rectifiers that turn a.c. into d.c., LEDs that turn current into light, photodiodes and solar cells that turn light into current, and the Zener diode that holds a voltage steady.

Every phone charger begins with the same job: take the $230\ \text{V}$, $50\ \text{Hz}$ alternating supply from the wall and turn it into a steady few volts of direct current. The heart of that job is a handful of diodes, each letting current through in one direction only. The same p–n junction, built from different materials and used in different ways, also lights the screen (LEDs), senses the ambient light (photodiodes), charges the battery from sunlight (solar cells) and keeps the voltage on the chip rock-steady when the battery runs down (Zener diodes).

In Section 19.1 we found the diode's I–V characteristic. Here we first replace that curve by two simple models — the ideal diode and the $0.7\ \text{V}$ model — that make circuit problems quick. We then build half-wave and full-wave rectifiers, study the I–V characteristics of the LED, photodiode, solar cell and Zener diode, and finish with the Zener voltage regulator and its load and series-resistor calculations.

Diode models and simple diode circuits

The real characteristic is curved, but in most circuits the diode is either far below its knee (practically no current) or well above it (a large current with an almost fixed voltage across it). That suggests replacing it by a switch.

📘 Definition 19.7 — The ideal diode and the 0.7 V model

An ideal diode is a perfect one-way switch: forward biased, it has zero resistance and zero voltage across it (a closed switch); reverse biased, it carries no current (an open switch).

In the constant-voltage-drop (0.7 V) model the diode conducts only when the voltage across it in the forward direction reaches $V_\gamma$ (about $0.7\ \text{V}$ for silicon, $0.3\ \text{V}$ for germanium); while it conducts the voltage across it stays exactly $V_\gamma$, whatever the current. Below $V_\gamma$, and in reverse bias, the current is zero. If a forward resistance $r_f$ is given, the conducting diode is $V_\gamma$ in series with $r_f$.

JEE problems say which model to use ("ideal diodes", "silicon diode with $0.7\ \text{V}$ drop"). With either model, a circuit with diodes is analysed by guessing the state of each diode and checking the guess.

🧭 Problem-solving strategy — Circuits with diodes
  1. For each diode, find its anode (p, triangle) and cathode (n, bar). Guess "on" if the battery tends to push conventional current from anode to cathode, otherwise "off".
  2. Replace an "on" diode by a short circuit (ideal) or a $0.7\ \text{V}$ drop opposing the current (0.7 V model); replace an "off" diode by a break.
  3. Solve the resulting ordinary circuit with Ohm's law and Kirchhoff's rules (Section 12.2).
  4. Check: every "on" diode must carry current from anode to cathode; every "off" diode must have its anode no higher than its cathode (plus $V_\gamma$). If a check fails, change that guess and repeat.
✏️ Example 1 — One diode, three models
A silicon diode, a $1.0\ \text{k}\Omega$ resistor and a $5.0\ \text{V}$ battery are in series, the diode forward biased. Find the current (a) treating the diode as ideal, (b) with the $0.7\ \text{V}$ model; (c) find the power dissipated in the diode in case (b). (d) What are the current and the voltage across the diode if the battery is reversed?
(a) Ideal: the diode is a short circuit, $I=\dfrac{5.0}{1000}=5.0\ \text{mA}$.
(b) $0.7\ \text{V}$ model: $I=\dfrac{5.0-0.7}{1000}=4.3\ \text{mA}$.
(c) $P=V_\gamma I=0.7\times4.3\times10^{-3}=3.0\ \text{mW}$.
(d) Reverse biased: $I=0$, so there is no drop across the resistor and the whole $5.0\ \text{V}$ appears across the diode (cathode positive).
Check The two models differ by $14\%$ here. The difference matters less as the supply voltage grows: with $50\ \text{V}$ it would be $1.4\%$.
✏️ Example 2 — Which diode conducts?
The positive terminal of a $12\ \text{V}$ battery is connected through a $2.0\ \text{k}\Omega$ resistor to a point P. Two branches join P to the negative terminal: branch 1 is a diode $D_1$ with its anode at P, in series with a $4.0\ \text{k}\Omega$ resistor; branch 2 is a diode $D_2$ with its cathode at P, in series with a $1.0\ \text{k}\Omega$ resistor. (a) Treating the diodes as ideal, find the current from the battery and the potential of P above the negative terminal. (b) Repeat with silicon diodes ($0.7\ \text{V}$ model). (c) The battery is reversed. Find the new current with ideal diodes.
Find the battery current in (a), with ideal diodes, before you open the solution:
States The battery makes P positive. $D_1$ has its anode at P: forward biased, "on". $D_2$ has its cathode at P: reverse biased, "off" — branch 2 carries no current.
(a) The circuit is $2.0+4.0=6.0\ \text{k}\Omega$ in series: $I=\dfrac{12}{6000}=2.0\ \text{mA}$. $V_P=12-(2.0\ \text{mA})(2.0\ \text{k}\Omega)=8.0\ \text{V}$. Check: $D_2$'s cathode is at $8.0\ \text{V}$ and its anode at $0$ — reverse biased ✓.
(b) $I=\dfrac{12-0.7}{6000}=1.9\ \text{mA}$ ($1.88\ \text{mA}$).
(c) Now P is driven negative: $D_1$ is off and $D_2$ on. $I=\dfrac{12}{2.0+1.0\ \text{k}\Omega}=4.0\ \text{mA}$.
⏱ Shortcut Two diodes facing opposite ways in parallel branches: exactly one conducts for each battery polarity. Find it, delete the other branch, and you have a single loop.

Two silicon diodes ($0.7\ \text{V}$ each) are connected in series, both forward biased, with a $100\ \Omega$ resistor across a $3.0\ \text{V}$ battery. The current is

The diode as a rectifier

A rectifier converts alternating current, which reverses direction every half-cycle, into current in one direction only. The input is usually the secondary of a step-down transformer (Section 14.3), giving $v=V_m\sin\omega t$ at the mains frequency $f$ ($50\ \text{Hz}$ in India).

📘 Definition 19.8 — Half-wave and full-wave rectifiers
  • Half-wave rectifier: one diode in series with the load $R_L$. The diode conducts during the half-cycles that make its anode positive and blocks the others, so the load receives only alternate half-cycles.
  • Full-wave rectifier (centre-tap): a transformer whose secondary has a centre tap, and two diodes. The ends A and B of the secondary are always in opposite phase: in one half-cycle $D_1$ (from A) conducts, in the next $D_2$ (from B), and both send current through the load in the same direction.
  • Full-wave rectifier (bridge): four diodes arranged in a bridge across an ordinary secondary. In each half-cycle two diagonally opposite diodes conduct, again sending current through the load the same way.

The output of all three is a pulsating d.c. — one-directional, but not steady.

📐 Result 19.6 — Output of a rectifier

For an input $v=V_m\sin\omega t$ at frequency $f$, a resistive load and no filter (with ideal diodes; subtract $0.7\ \text{V}$ for each conducting silicon diode in the path to get the output peak):

rectifieroutput peakoutput frequencyaverage outputpeak inverse voltage
half-wave (1 diode)$V_m$ (Si: $V_m-0.7$)$f$$V_m/\pi$$V_m$
centre-tap (2 diodes)$V_m$ (Si: $V_m-0.7$)$2f$$2V_m/\pi$$2V_m$
bridge (4 diodes)$V_m$ (Si: $V_m-1.4$)$2f$$2V_m/\pi$$V_m$

For the centre-tap circuit $V_m$ is the peak voltage of each half of the secondary. The peak inverse voltage (PIV) is the largest reverse voltage a diode must withstand; a diode is chosen with a breakdown voltage above it. The output frequency is the number of output pulses per second: a full-wave rectifier makes a pulse in every half-cycle, so its output repeats twice as often as the input.

Smoothing the output. To turn the pulses into an almost steady voltage, a capacitor (the filter capacitor) is connected in parallel with the load. While the rectified voltage is rising, the diode conducts and charges the capacitor up to the peak voltage. When the rectified voltage falls below the capacitor's voltage, the diode is reverse biased and stops conducting, and the capacitor slowly discharges through $R_L$, keeping the output up until the next peak recharges it. What remains is a small saw-tooth variation called the ripple, at the output frequency. The ripple is smaller when the time constant $R_LC$ is much longer than the time between peaks — so a larger capacitor, a larger load resistance (smaller load current) and a full-wave circuit (recharged twice as often) all give a smoother output.

✏️ Example 3 — From the mains to a 12 V supply
A transformer with turns ratio $23:1$ steps down $230\ \text{V}$ (rms), $50\ \text{Hz}$ mains. Its secondary feeds a load through (a) a half-wave rectifier with one silicon diode, (b) a bridge rectifier of silicon diodes. For each, find the output peak voltage, the output frequency and the peak inverse voltage on each diode. (c) With ideal diodes, find the average output voltage of each.
Find the bridge rectifier's output peak voltage before you open the solution:
Secondary $V_{\text{rms}}=\dfrac{230}{23}=10\ \text{V}$, so $V_m=10\sqrt2=14.1\ \text{V}$.
(a) Half-wave: peak $=14.1-0.7=13.4\ \text{V}$; output frequency $50\ \text{Hz}$; PIV $=V_m=14.1\ \text{V}$.
(b) Bridge: two diodes conduct in series, so peak $=14.1-1.4=12.7\ \text{V}$; output frequency $100\ \text{Hz}$; PIV $\approx V_m=14.1\ \text{V}$ (strictly $V_m-0.7$, since the conducting diode in the same arm holds $0.7\ \text{V}$).
(c) Half-wave: $\dfrac{V_m}{\pi}=\dfrac{14.14}{\pi}=4.50\ \text{V}$; bridge: $\dfrac{2V_m}{\pi}=9.00\ \text{V}$ — twice as much, because no half-cycle is wasted.
Check Neither average equals the rms $10\ \text{V}$ or the peak: "average" means the d.c. value a moving-coil meter would read. A filter capacitor raises the d.c. output towards the peak.
🚀 Beyond JEE Main — how big is the ripple?

Not named in the JEE Main 2026 list (which asks for ripple only qualitatively) or the JEE Advanced 2026 syllabus. For interest only; nothing here is used in the exercises, the Exam corner or the quiz.

Between peaks the capacitor supplies the load current $I_L\approx V_m/R_L$ for almost the whole interval $1/f_r$, where $f_r$ is the ripple (output) frequency. The charge it loses is $I_L/f_r$, so its voltage drops by about $\Delta V\approx\dfrac{I_L}{f_rC}=\dfrac{V_m}{f_rR_LC}$, valid when $R_LC\gg1/f_r$. For a bridge on $50\ \text{Hz}$ ($f_r=100\ \text{Hz}$) with $V_m=12\ \text{V}$, $R_L=100\ \Omega$ and $C=2200\ \mu\text{F}$: $\Delta V\approx\dfrac{12}{100\times100\times2.2\times10^{-3}}=0.55\ \text{V}$. A half-wave circuit with the same capacitor would ripple twice as much.

A bridge rectifier of silicon diodes is fed with $V_m=10\ \text{V}$ at $50\ \text{Hz}$, with no filter capacitor. What are the output peak and the output frequency?

Choose the bridge, silicon diodes, $V_m=10\ \text{V}$ and no filter: the readouts show an output peak of $8.60\ \text{V}$ and an output frequency of $100\ \text{Hz}$. In each half-cycle current passes through two diodes in series, so $2\times0.7=1.4\ \text{V}$ is lost; and every half-cycle gives a pulse, so the pulses come twice per input cycle. Watch which pair of diodes lights up in each half-cycle.
Interactive 1 — Rectifier Oscilloscope

Choose the rectifier, the diode model, the input peak voltage $V_m$ ($50\ \text{Hz}$) and a filter capacitor, then press Play. Left: the circuit, with the diodes that are conducting at the cursor's instant shown in green. Right: the input (top; for the centre-tap circuit, the voltage of end A of the secondary) and the voltage across the load (bottom) over three input cycles. Add a capacitor and watch the diodes conduct only in short bursts near each peak while the ripple shrinks.

10 V
output peak—
output frequency—
average output—
ripple (peak to peak)—

A full-wave rectifier is fed from a $60\ \text{Hz}$ supply (as used in some countries). With a filter capacitor, the ripple on its output has frequency

Optoelectronic diodes: the LED, the photodiode and the solar cell

In Section 19.1 we saw that an electron crossing the band gap downwards releases an energy $E_g$, and that a photon of energy at least $E_g$ can lift one across. Three devices exploit these two processes in a p–n junction: the LED makes light from current, the photodiode measures light, and the solar cell turns light into electrical power.

📘 Definition 19.9 — Light-emitting diode (LED)

An LED is a heavily doped p–n junction, made of a semiconductor such as gallium arsenide phosphide or gallium nitride, that emits light when forward biased. Electrons and holes injected across the junction recombine, and in these materials most of the energy released in each recombination (about $E_g$) comes out as a photon:

$$h\nu\approx E_g,\qquad \lambda\,(\text{nm})\approx\frac{1240}{E_g\,(\text{eV})}.$$

Visible LEDs therefore need $1.8\ \text{eV}\lesssim E_g\lesssim3\ \text{eV}$; infrared LEDs (remote controls) use smaller gaps. Silicon and germanium are not used: in them the energy goes into heating the crystal.

I–V characteristic of an LED. It has the shape of an ordinary diode's curve, but the knee voltage is roughly $E_g/e$ — about $1.8\ \text{V}$ for red, $2\ \text{V}$ for yellow-green, $3\ \text{V}$ for blue — so the curve sits further to the right for shorter wavelengths. The light output increases with the forward current, and in practice an LED is always driven through a series resistor that sets the current (typically $5$–$30\ \text{mA}$). The reverse breakdown voltage is low, often only about $5\ \text{V}$, so an LED must not be reverse biased strongly. Compared with filament lamps, LEDs work at low voltage and power, switch on and off in nanoseconds, last far longer, need no warming up and give nearly single-coloured light (a spread of only some tens of nanometres).

📘 Definition 19.10 — Photodiode and solar cell

A photodiode is a p–n junction with a window that lets light reach the depletion region, operated in reverse bias. Each absorbed photon with $h\nu\ge E_g$ creates an electron–hole pair; the strong field of the depletion region separates them (electrons to the n side, holes to the p side), adding to the reverse current. The extra reverse current is proportional to the light intensity.

A solar cell is a large-area p–n junction with no external bias. Light creates electron–hole pairs near the junction (generation), the junction field drives electrons to the n side and holes to the p side (separation), and the contacts collect them (collection). The p side becomes positive: the cell is a source of emf that drives current through an external load — the photovoltaic effect.

Why reverse bias for a photodiode? The reverse current without light is only the tiny minority-carrier current $I_0$, while the photocurrent is of the same order, so light changes the reverse current by a large fraction and is easy to measure. In forward bias the photocurrent would be swamped by the large majority-carrier current. The characteristics are therefore a family of nearly horizontal lines in the third quadrant (negative $V$, negative $I$), each one lower for a greater intensity.

📐 Result 19.7 — The solar cell's I–V characteristic
  • The illuminated cell's characteristic lies in the fourth quadrant (positive $V$, negative $I$ in the diode convention): the cell delivers power instead of absorbing it. It is usually drawn flipped into the first quadrant as current against voltage.
  • It cuts the axes at the open-circuit voltage $V_{oc}$ (no current drawn; about $0.5$–$0.6\ \text{V}$ for silicon) and the short-circuit current $I_{sc}$ (zero load resistance), which is proportional to the light intensity.
  • The power delivered is $P=VI$; it is zero at both intercepts and greatest at one point of the curve, $P_{\max}=V_mI_m\lt V_{oc}I_{sc}$. The efficiency is $\eta=\dfrac{P_{\max}}{I_{\text{light}}\,A}$, where $I_{\text{light}}$ is the intensity (W/m²) and $A$ the area of the cell.
  • Good solar-cell materials have $E_g$ near $1.0$–$1.8\ \text{eV}$ (Si $1.1$, GaAs $1.4\ \text{eV}$): most of the Sun's energy arrives in photons of $1$–$3\ \text{eV}$; a much larger gap wastes the many photons below it, a much smaller one wastes the excess energy of each photon as heat.
✏️ Example 4 — Light in, light out
(a) A GaAsP LED has $E_g=1.9\ \text{eV}$. Estimate the wavelength and colour of its light. (b) It is run from a $9.0\ \text{V}$ battery at $20\ \text{mA}$, with $2.0\ \text{V}$ across it. What series resistor is needed? (c) A photodiode has $E_g=2.8\ \text{eV}$. Which of the wavelengths $400$, $550$ and $700\ \text{nm}$ can it detect? (d) A $10\ \text{cm}\times10\ \text{cm}$ silicon solar cell in sunlight of intensity $1000\ \text{W/m}^2$ delivers its maximum power at $0.50\ \text{V}$ and $2.9\ \text{A}$. Find its efficiency. ($hc=1240\ \text{eV nm}$.)
(a) $\lambda\approx\dfrac{1240}{1.9}=650\ \text{nm}$: red.
(b) The resistor takes $9.0-2.0=7.0\ \text{V}$ at $20\ \text{mA}$: $R=\dfrac{7.0}{0.020}=350\ \Omega$.
(c) $\lambda_{\max}=\dfrac{1240}{2.8}=443\ \text{nm}$. Only $400\ \text{nm}$ (photon energy $3.1\ \text{eV}\gt2.8\ \text{eV}$) is detected; $550\ \text{nm}$ ($2.25\ \text{eV}$) and $700\ \text{nm}$ ($1.77\ \text{eV}$) are not.
(d) $P_{\max}=0.50\times2.9=1.45\ \text{W}$; incident power $=1000\times0.010=10\ \text{W}$; $\ \eta=\dfrac{1.45}{10}=14.5\%$.
Check Area: $10\ \text{cm}\times10\ \text{cm}=100\ \text{cm}^2=0.010\ \text{m}^2$ — the usual slip is $0.10\ \text{m}^2$, which would give an efficiency of $1.45\%$.

Which line correctly gives the bias at which each device is normally operated?

The Zener diode and voltage regulation

An ordinary diode is ruined by reverse breakdown. If instead the junction is made from heavily doped material, its depletion layer is very thin and its field enormous, and breakdown happens at a low, sharply defined voltage that the diode can survive indefinitely — provided the current is limited. Such a diode is designed to be used in breakdown.

📘 Definition 19.11 — Zener diode

A Zener diode is a heavily doped p–n junction designed to operate in reverse breakdown. Its circuit symbol is a diode with a bent bar. Its reverse current stays negligible until the reverse voltage reaches the Zener (breakdown) voltage $V_Z$; then the current can rise over a wide range while the voltage across the diode stays almost exactly $V_Z$. Zener diodes are made with $V_Z$ from about $2\ \text{V}$ to $200\ \text{V}$. In forward bias a Zener diode behaves like an ordinary diode.

In the thin depletion layer the field (of order $10^7$–$10^8\ \text{V/m}$) is strong enough to pull valence electrons straight out of their bonds (internal field emission), producing a large number of carriers — this is Zener breakdown. In diodes with higher $V_Z$, carriers accelerated by the field knock out further electrons in a chain (avalanche breakdown). Either way, the diode is safe as long as its power $V_ZI_Z$ stays within its rating.

The almost vertical reverse characteristic is exactly what a voltage regulator needs: whatever the current, the voltage stays at $V_Z$. In a Zener regulator the unregulated d.c. input $V_{in}$ (for example, the output of a filtered rectifier, which varies with the mains and with the ripple) is connected through a series resistor $R_s$ to the Zener diode, reverse biased (cathode to the positive side), and the load $R_L$ is connected in parallel with the Zener.

📐 Result 19.8 — The Zener voltage regulator

Is the Zener in breakdown? Remove it and find the voltage the divider would give across the load: $V_{\text{open}}=\dfrac{V_{in}R_L}{R_s+R_L}$. If $V_{\text{open}}\ge V_Z$ the Zener conducts and the load voltage is held at $V_Z$; if $V_{\text{open}}\lt V_Z$ the Zener carries no current and $V_L=V_{\text{open}}$ (no regulation).

When it regulates:

$$V_L=V_Z,\qquad I_s=\frac{V_{in}-V_Z}{R_s},\qquad I_L=\frac{V_Z}{R_L},$$ $$I_Z=I_s-I_L,\qquad P_Z=V_ZI_Z .$$

A change in $V_{in}$ changes $I_s$ and $I_Z$ but not $V_L$: the extra voltage is dropped across $R_s$. A change in the load shifts current between the Zener and the load, $I_Z+I_L=I_s$ staying fixed. Regulation fails if $I_Z$ falls below the small minimum needed to stay in breakdown, and the diode overheats if $I_Z$ exceeds $I_{Z,\max}=P_{\max}/V_Z$.

✏️ Example 5 — A 9 V regulator
A $9.0\ \text{V}$ Zener diode is fed from $15\ \text{V}$ through $R_s=500\ \Omega$. (a) With a $1.5\ \text{k}\Omega$ load, find $I_s$, $I_L$, $I_Z$ and the power in the Zener. (b) Find $I_Z$ if the load is disconnected. (c) The load is changed to $500\ \Omega$. Find the load voltage.
Check $V_{\text{open}}=15\times\dfrac{1500}{2000}=11.25\ \text{V}\gt9.0\ \text{V}$: the Zener is in breakdown.
(a) $I_s=\dfrac{15-9.0}{500}=12\ \text{mA}$; $\ I_L=\dfrac{9.0}{1500}=6.0\ \text{mA}$; $\ I_Z=12-6.0=6.0\ \text{mA}$; $\ P_Z=9.0\times6.0\times10^{-3}=54\ \text{mW}$.
(b) No load: all of $I_s$ goes through the Zener, $I_Z=12\ \text{mA}$ ($P_Z=108\ \text{mW}$) — the worst case for the Zener's power rating.
(c) $V_{\text{open}}=15\times\dfrac{500}{1000}=7.5\ \text{V}\lt9.0\ \text{V}$: the Zener is not in breakdown and carries no current. $V_L=7.5\ \text{V}$ — the regulator has dropped out.
⏱ Shortcut Blindly using $I_Z=I_s-I_L$ in (c) gives $12-18=-6\ \text{mA}$: a negative Zener current is the sign that the Zener is off. Always do the open-circuit check first.
✏️ Example 6 — Designing the series resistor
An unregulated supply varies between $12\ \text{V}$ and $18\ \text{V}$. It is to provide $6.0\ \text{V}$ to a load that draws $20\ \text{mA}$, using a $6.0\ \text{V}$ Zener diode rated at $0.60\ \text{W}$ that needs at least $5.0\ \text{mA}$ to stay in breakdown. (a) Find the largest series resistance that keeps the output regulated. (b) Find the smallest series resistance that protects the Zener if the load may be disconnected. (c) Is the design still safe at the smallest $R_s$ found by ignoring the possible disconnection?
Find the allowed range of $R_s$ before you open the solution:
Limits $I_{Z,\max}=\dfrac{0.60}{6.0}=100\ \text{mA}$; $\ I_{Z,\min}=5.0\ \text{mA}$; $\ I_L=20\ \text{mA}$.
(a) At the lowest input with the load connected, $I_s$ must be at least $I_L+I_{Z,\min}=25\ \text{mA}$: $\ \dfrac{12-6.0}{R_s}\ge0.025$, so $R_s\le240\ \Omega$.
(b) At the highest input with no load, the whole of $I_s$ flows through the Zener: $\dfrac{18-6.0}{R_s}\le0.100$, so $R_s\ge120\ \Omega$. The design range is $120\ \Omega\le R_s\le240\ \Omega$.
(c) With the load always connected, the condition would be $\dfrac{12}{R_s}\le I_{Z,\max}+I_L=0.120\ \text{A}$, i.e. $R_s\ge100\ \Omega$. But at $R_s=100\ \Omega$ and no load, $I_Z=\dfrac{12}{100}=120\ \text{mA}\gt100\ \text{mA}$ ($0.72\ \text{W}$): the Zener would overheat. A safe design must survive the load being removed.
⏱ Shortcut $R_{s,\max}$: lowest $V_{in}$, largest load current, smallest $I_Z$. $R_{s,\min}$: highest $V_{in}$, smallest load current, largest $I_Z$. Write the two worst cases first and everything else follows.

A $6.0\ \text{V}$ Zener regulator has $R_s=300\ \Omega$ and $R_L=600\ \Omega$. At $V_{in}=15\ \text{V}$, what current flows through the Zener?

Set $R_s=300\ \Omega$, $R_L=600\ \Omega$ and $V_{in}=15\ \text{V}$: the readouts show $I_s=30.0\ \text{mA}$, $I_L=10.0\ \text{mA}$ and $I_Z=20.0\ \text{mA}$, with $V_L=6.00\ \text{V}$. $30\ \text{mA}$ is the series current — it divides between the load and the Zener. Now lower $V_{in}$: the output stays at $6.00\ \text{V}$ until $V_{in}=6.0\times\tfrac{900}{600}=9.0\ \text{V}$, below which the Zener switches off and $V_L$ follows the input.
Interactive 2 — Zener Voltage Regulator

A $6.0\ \text{V}$ Zener diode rated at $0.25\ \text{W}$ ($I_{Z,\max}=41.7\ \text{mA}$) regulates the voltage across the load $R_L$. Set the input voltage, the series resistor and the load. Left: the circuit, with arrows whose thickness shows the currents $I_s$, $I_Z$ and $I_L$. Right: the load voltage against the input voltage — the flat part is regulation. Press Play to sweep $V_{in}$ and watch the Zener take up the extra current while $V_L$ stays put.

12.0 V300 Ω600 Ω
series current $I_s$—
load current $I_L$—
Zener current $I_Z$—
load voltage $V_L$—
⚠️ JEE Main traps

1. Output frequency. Half-wave: $f$; full-wave (centre-tap or bridge): $2f$. "Ripple frequency" is the output frequency, not the input's.

2. Counting diode drops. In a bridge, current passes through two diodes in each half-cycle ($1.4\ \text{V}$ lost with silicon); in a half-wave or centre-tap circuit through one. Diodes in parallel branches do not add drops.

3. Using $I_Z=I_s-I_L$ without checking breakdown. First check $V_{in}R_L/(R_s+R_L)\ge V_Z$. A negative $I_Z$ means the Zener is off and $V_L$ is set by the divider.

4. Bias of the optoelectronic diodes. LED: forward. Photodiode: reverse. Solar cell: none (it is the source). A Zener regulator: reverse, in breakdown.

5. Peak, rms and average. Transformer and mains values are rms: multiply by $\sqrt2$ for $V_m$ before subtracting diode drops; averages $V_m/\pi$ and $2V_m/\pi$ use the peak.

In a working Zener regulator the input voltage rises from $12\ \text{V}$ to $14\ \text{V}$ while the load stays the same. Which quantity stays (almost) the same?

Exercises

Use the $0.7\ \text{V}$ model for silicon and $0.3\ \text{V}$ for germanium diodes unless the diodes are called ideal. Take $hc=1240\ \text{eV nm}$; mains and transformer voltages are rms values.

I
Diode circuits.
  • 1 A silicon diode is forward biased in series with a $2.2\ \text{k}\Omega$ resistor across a $9.0\ \text{V}$ battery. Find the current.
  • 2 Find the current in part 1 if the diode is treated as ideal.
  • 3 A germanium diode and a silicon diode are connected in parallel, both pointing the same way, and fed from a $5.0\ \text{V}$ battery through $1.0\ \text{k}\Omega$. Which diode conducts, and what is the current?
  • 4 Two silicon diodes in series, both forward biased, are connected with a $200\ \Omega$ resistor across $6.0\ \text{V}$. Find the current.
  • 5 In part 1 the battery is reversed. Find the current and the voltages across the resistor and across the diode.
  • 6 A $10\ \text{V}$ battery drives current through $5\ \Omega$ into two parallel branches: a $10\ \Omega$ resistor, and an ideal diode in series with another $10\ \Omega$ resistor. Find the battery current with the diode forward biased, and with it reversed.
  • 7 A silicon diode with forward resistance $10\ \Omega$ (and $0.7\ \text{V}$ drop) is in series with $220\ \Omega$ across $3.0\ \text{V}$. Find the current.
  • 8 Find the power dissipated in the diode of part 1.
1 $I=\dfrac{9.0-0.7}{2200}=3.8\ \text{mA}$ ($3.77\ \text{mA}$).
2 $I=\dfrac{9.0}{2200}=4.1\ \text{mA}$.
3 Only the germanium diode: once it conducts it holds the parallel pair at $0.3\ \text{V}$, too little for the silicon diode to reach $0.7\ \text{V}$. $I=\dfrac{5.0-0.3}{1000}=4.7\ \text{mA}$.
4 $I=\dfrac{6.0-1.4}{200}=0.023\ \text{A}=23\ \text{mA}$.
5 $I=0$; $0\ \text{V}$ across the resistor, the full $9.0\ \text{V}$ across the diode.
6 Forward: the two $10\ \Omega$ branches are in parallel ($5\ \Omega$), total $10\ \Omega$, $I=1.0\ \text{A}$. Reversed: the diode branch is open, total $15\ \Omega$, $I=0.67\ \text{A}$.
7 $I=\dfrac{3.0-0.7}{220+10}=\dfrac{2.3}{230}=10\ \text{mA}$.
8 $P=0.7\times3.77\times10^{-3}=2.6\ \text{mW}$.
II
Rectifiers.
  • 1 The input to a rectifier is at $50\ \text{Hz}$. What is the output frequency of (a) a half-wave, (b) a full-wave rectifier?
  • 2 A transformer steps $220\ \text{V}$ down to $12\ \text{V}$. Find the peak voltage of the secondary.
  • 3 The secondary of part 2 feeds a bridge of silicon diodes and a $500\ \Omega$ load. Find the peak output voltage and the peak load current.
  • 4 A centre-tap rectifier uses a secondary of $12\ \text{V}$ on each side of the tap. Find the peak inverse voltage on each (ideal) diode.
  • 5 A half-wave rectifier with an ideal diode is fed with a sinusoid of peak $20\ \text{V}$. Find the average (d.c.) output voltage.
  • 6 Explain how a capacitor across the load reduces the ripple. What happens to the ripple if (a) $C$ is doubled, (b) the load draws more current?
  • 7 How many diodes of a bridge rectifier conduct at any instant? What does the output look like if one diode burns out (open circuit)?
  • 8 An oscilloscope shows the unfiltered output of a rectifier fed from $50\ \text{Hz}$: identical positive humps, touching each other, every $10\ \text{ms}$. What kind of rectifier is it?
1 (a) $50\ \text{Hz}$; (b) $100\ \text{Hz}$.
2 $V_m=12\sqrt2=17.0\ \text{V}$.
3 Peak $=17.0-1.4=15.6\ \text{V}$; peak current $=\dfrac{15.6}{500}=31\ \text{mA}$.
4 $V_m=17.0\ \text{V}$ per half; the non-conducting diode sees both halves: PIV $=2V_m=33.9\ \text{V}$.
5 $\dfrac{V_m}{\pi}=\dfrac{20}{\pi}=6.4\ \text{V}$ ($6.37\ \text{V}$).
6 The capacitor charges to the peak and then supplies the load between peaks, discharging only slowly if $R_LC$ is long compared with the time between peaks. (a) Doubling $C$ roughly halves the ripple; (b) a larger load current discharges it faster, so the ripple grows.
7 Two (diagonally opposite) at a time. With one diode open, the half-cycles that needed it are lost: the output becomes half-wave (at $f$, not $2f$).
8 Pulses every $10\ \text{ms}$ means $100$ per second $=2\times50\ \text{Hz}$: a full-wave rectifier (centre-tap or bridge).
III
LEDs, photodiodes and solar cells.
  • 1 An LED emits light of wavelength $620\ \text{nm}$. Estimate the band gap of its material.
  • 2 A blue LED is made from material with $E_g=2.76\ \text{eV}$. Find the wavelength it emits.
  • 3 An LED with a forward voltage of $2.1\ \text{V}$ is to carry $15\ \text{mA}$ from a $5.0\ \text{V}$ supply. Find the series resistance.
  • 4 A photodiode is made of a semiconductor with $E_g=2.0\ \text{eV}$. Which of $450$, $600$ and $700\ \text{nm}$ light can it detect?
  • 5 Why is a photodiode operated in reverse bias rather than forward bias?
  • 6 A solar cell of area $100\ \text{cm}^2$ in sunlight of $1000\ \text{W/m}^2$ gives its maximum power at $0.48\ \text{V}$ and $2.9\ \text{A}$. Find the maximum power and the efficiency.
  • 7 Why are silicon ($1.1\ \text{eV}$) and gallium arsenide ($1.4\ \text{eV}$) good solar-cell materials while gallium nitride ($3.4\ \text{eV}$) is not?
  • 8 In which quadrant of the I–V plane do the characteristics of (a) an illuminated photodiode in use, (b) an illuminated solar cell lie? What do the intercepts of the solar-cell curve represent?
1 $E_g\approx\dfrac{1240}{620}=2.0\ \text{eV}$.
2 $\lambda\approx\dfrac{1240}{2.76}=449\ \text{nm}$.
3 $R=\dfrac{5.0-2.1}{0.015}=193\ \Omega$ (use the next standard value, e.g. $200\ \Omega$, slightly reducing the current).
4 $\lambda_{\max}=\dfrac{1240}{2.0}=620\ \text{nm}$: it detects $450$ and $600\ \text{nm}$, not $700\ \text{nm}$.
5 In reverse bias the dark current is only the tiny minority current, so the photocurrent changes it by a large fraction (and is proportional to intensity). In forward bias the large majority-carrier current would hide the photocurrent.
6 $P_{\max}=0.48\times2.9=1.39\ \text{W}$; incident power $=1000\times0.010=10\ \text{W}$; efficiency $=13.9\%$.
7 Most solar energy arrives in photons of about $1$–$3\ \text{eV}$. A $3.4\ \text{eV}$ gap would let almost all of them pass unabsorbed; gaps of $1.1$–$1.4\ \text{eV}$ absorb most photons while wasting only a moderate part of each photon's energy as heat.
8 (a) Third quadrant (reverse $V$, reverse current). (b) Fourth quadrant: $V$ positive, current leaving through the p terminal. The intercepts are the open-circuit voltage $V_{oc}$ (on the $V$ axis) and the short-circuit current $I_{sc}$ (on the $I$ axis).
IV
The Zener diode and voltage regulation.
  • 1 A $5.1\ \text{V}$ Zener is fed from $12\ \text{V}$ through $300\ \Omega$ with no load. Find the Zener current.
  • 2 A $510\ \Omega$ load is connected across the Zener of part 1. Check that it is still in breakdown and find the load and Zener currents.
  • 3 Find the power dissipated in the Zener in part 2.
  • 4 In the circuit of part 1, what is the smallest load resistance for which the output stays regulated (take the minimum Zener current as zero)?
  • 5 A $10\ \text{V}$ Zener diode is rated at $0.50\ \text{W}$. What is the largest current it can safely carry?
  • 6 A $6.0\ \text{V}$ Zener with $R_s=200\ \Omega$ feeds a $1.2\ \text{k}\Omega$ load. The Zener current must stay between $2.0\ \text{mA}$ and $40\ \text{mA}$. Find the range of input voltage over which the circuit regulates safely.
  • 7 What happens if the Zener diode in a regulator is accidentally connected the other way round (forward biased)?
  • 8 Why does heavy doping give a low breakdown voltage?
1 $I_Z=I_s=\dfrac{12-5.1}{300}=23\ \text{mA}$.
2 $V_{\text{open}}=12\times\dfrac{510}{810}=7.6\ \text{V}\gt5.1\ \text{V}$ ✓. $I_L=\dfrac{5.1}{510}=10\ \text{mA}$; $\ I_Z=23-10=13\ \text{mA}$.
3 $P_Z=5.1\times0.013=66\ \text{mW}$.
4 Regulation needs $I_L\le I_s=23\ \text{mA}$: $R_L\ge\dfrac{5.1}{0.023}=222\ \Omega$. (Check: at $222\ \Omega$, $V_{\text{open}}=12\times\tfrac{222}{522}=5.1\ \text{V}$ ✓.)
5 $I_{\max}=\dfrac{P}{V_Z}=\dfrac{0.50}{10}=50\ \text{mA}$.
6 $I_L=\dfrac{6.0}{1200}=5.0\ \text{mA}$, so $I_s$ must lie between $7.0$ and $45\ \text{mA}$: $V_{in}=6.0+200I_s$ ranges from $6.0+1.4=7.4\ \text{V}$ to $6.0+9.0=15\ \text{V}$.
7 Forward biased, it acts as an ordinary diode: the output is held at only about $0.7\ \text{V}$ and no longer at $V_Z$.
8 Heavy doping makes the depletion layer very thin, so even a few volts produce a field large enough ($\sim10^7$–$10^8\ \text{V/m}$) to tear electrons out of their bonds.
🎯 Exam corner JEE Main · MCQJEE Main · Numerical

E1. JEE Main · MCQ A full-wave bridge rectifier is connected to a $50\ \text{Hz}$ a.c. supply. The fundamental frequency of the ripple in its output is (A) $25\ \text{Hz}$ (B) $50\ \text{Hz}$ (C) $100\ \text{Hz}$ (D) $200\ \text{Hz}$

Idea Each half-cycle of the input produces one output pulse in the same direction, so there are $2\times50$ pulses per second.
Answer (C) $100\ \text{Hz}$.
⏱ Shortcut Half-wave: $f$. Full-wave of either kind: $2f$. The number of diodes does not matter.

E2. JEE Main · Numerical An $8.0\ \text{V}$ Zener diode is connected with a series resistance of $400\ \Omega$ to a $20\ \text{V}$ d.c. supply, and a load of $1.0\ \text{k}\Omega$ is connected across the Zener. Find the current through the Zener diode in mA. Give the answer to the nearest integer.

Check $V_{\text{open}}=20\times\dfrac{1000}{1400}=14.3\ \text{V}\gt8.0\ \text{V}$: the Zener is in breakdown, $V_L=8.0\ \text{V}$.
Currents $I_s=\dfrac{20-8.0}{400}=30\ \text{mA}$; $\ I_L=\dfrac{8.0}{1000}=8.0\ \text{mA}$; $\ I_Z=30-8.0=22\ \text{mA}$.
Answer $22$.

E3. JEE Main · MCQ Which statement is correct? (A) A photodiode is operated in forward bias so that its current is large. (B) An LED emits light when reverse biased beyond breakdown. (C) A solar cell needs an external reverse bias to separate the carriers. (D) The photocurrent of a reverse-biased photodiode is proportional to the intensity of the light falling on it.

Check each (A) Wrong — photodiodes are reverse biased so that light changes the small reverse current by a large fraction. (B) Wrong — an LED emits in forward bias, by recombination. (C) Wrong — the junction's own field separates the carriers; a solar cell has no bias.
(D) Each absorbed photon (with $h\nu\ge E_g$) yields one electron–hole pair, so the photocurrent is proportional to the number of photons per second, i.e. to the intensity.
Answer (D).

E4. JEE Main · Numerical A red LED needs $1.8\ \text{V}$ across it and a current of $16\ \text{mA}$. It is to be run from a $5.0\ \text{V}$ supply. Find the series resistance needed, in ohms. Give the answer to the nearest integer.

Idea The resistor takes the rest of the supply voltage at the same current.
Number $R=\dfrac{5.0-1.8}{16\times10^{-3}}=\dfrac{3.2}{0.016}=200\ \Omega$.
Answer $200$.

E5. JEE Main · MCQ A Zener diode of breakdown voltage $8\ \text{V}$ is connected through a $1\ \text{k}\Omega$ series resistor to a $12\ \text{V}$ supply, and a $1\ \text{k}\Omega$ load is connected across the Zener. The voltage across the load is (A) $8\ \text{V}$ (B) $6\ \text{V}$ (C) $4\ \text{V}$ (D) $12\ \text{V}$

Check Without the Zener the divider gives $12\times\dfrac{1}{1+1}=6\ \text{V}\lt8\ \text{V}$. The Zener never reaches breakdown, so it carries no current.
Result $V_L=6\ \text{V}$ — the circuit is just a potential divider.
Answer (B).
⏱ Shortcut (A) is the trap: "a Zener is there, so the output is $V_Z$". Using $I_Z=I_s-I_L=4-8=-4\ \text{mA}$ would warn you too.

E6. JEE Main · Numerical A solar cell of area $20\ \text{cm}^2$ is exposed to sunlight of intensity $1000\ \text{W/m}^2$. At its maximum-power point the voltage is $0.45\ \text{V}$ and the current $0.40\ \text{A}$. Find its efficiency in per cent. Give the answer to the nearest integer.

Output $P_{\max}=0.45\times0.40=0.18\ \text{W}$.
Input $A=20\ \text{cm}^2=2.0\times10^{-3}\ \text{m}^2$; incident power $=1000\times2.0\times10^{-3}=2.0\ \text{W}$.
Answer $\eta=\dfrac{0.18}{2.0}=0.09$, i.e. $9$.
⏱ Shortcut $1\ \text{cm}^2=10^{-4}\ \text{m}^2$, so at $1000\ \text{W/m}^2$ each cm² receives $0.1\ \text{W}$: $20\ \text{cm}^2$ gets $2\ \text{W}$.
🔬 Research–Teaching NexusResearch-tutored · optional, about 45 minutes

Research question. At what load does a small solar cell deliver its greatest power, and how do its open-circuit voltage and short-circuit current change as the light gets brighter?

Why it matters. Rooftop and utility-scale solar plants — India aims for hundreds of gigawatts of solar capacity — use electronic "maximum-power-point trackers" that keep adjusting the load so that every panel works at the top of its power curve. Engineers rate panels by their $V_{oc}$, $I_{sc}$, maximum power and efficiency, all of which come from exactly the I–V curve of this section.

What to do.

  1. Take a small solar cell or garden-light panel. Connect a variable resistor (a few ohms to a few kilohms, or a box of fixed resistors) across it, with an ammeter in series and a voltmeter across the cell.
  2. In steady sunlight (or under a fixed desk lamp), record $V$ and $I$ for $10$–$15$ load values, including open circuit ($V_{oc}$) and a short circuit through the ammeter ($I_{sc}$).
  3. Plot $I$ against $V$, and $P=VI$ against $V$. Find the maximum-power point and the load resistance $R=V_m/I_m$ that gives it.
  4. Repeat with the cell partly covered (or the lamp farther away). How do $I_{sc}$ and $V_{oc}$ change? Is $I_{sc}$ proportional to the uncovered area?
  5. Estimate the efficiency, taking the intensity of full sunlight as about $1000\ \text{W/m}^2$ (or measuring it with a phone light-meter app and a published conversion).

Tools: Small solar cell or panel, variable resistor or resistor set, two multimeters, connecting wires, ruler, spreadsheet.

Hand in: The I–V and P–V graphs, $V_{oc}$, $I_{sc}$, $P_{\max}$, the best load resistance, the efficiency estimate, and a paragraph explaining why $I_{sc}$ follows the light intensity closely while $V_{oc}$ hardly changes.

Going further. Heat the cell gently with a hair dryer while it is illuminated. Which of $V_{oc}$ and $I_{sc}$ changes more? Use the temperature behaviour of a diode from Section 19.1 to explain why hot panels in a Rajasthan summer give less power.

Instructor note: garden-light cells typically give $V_{oc}$ of $2$–$6\ \text{V}$ (several cells in series) and $I_{sc}$ of tens of mA in full sun; the maximum-power point lies at about $75$–$85\%$ of $V_{oc}$. $I_{sc}$ scales almost exactly with uncovered area, while $V_{oc}$ changes only logarithmically with intensity. Efficiencies of $5$–$15\%$ are normal for cheap cells; clouds passing during the run are the main source of scatter.

🧪 Self-check quiz

0/5 correct

Q1. An ideal diode that is reverse biased behaves like

Q2. In a bridge rectifier, during each half-cycle of the input,

Q3. Three LEDs emit red, green and blue light. Their band gaps are, from smallest to largest,

Q4. A Zener diode used as a voltage regulator is operated

Q5. An illuminated solar cell delivers no power when