Chapter 1 · Introduction

Chapter 1 — Units and Measurements

Every result in physics is a number, a unit and an uncertainty. This chapter builds the SI and its base units, the rules for significant figures, dimensional analysis and the arithmetic of errors — the toolkit behind every later chapter.

Until May 2019 the kilogram was a lump of platinum–iridium locked in a vault near Paris, and every bathroom scale in the world was, through a long chain of comparisons, checked against it. Then the lump was retired. Today the kilogram is fixed by giving the Planck constant an exact value, $h=6.626\,070\,15\times10^{-34}\ \text{J s}$, and any well-equipped laboratory can realise it. The change was invisible in daily life, but it says something deep: a unit is an agreement, and the whole of physics rests on a handful of such agreements — seven base units from which every other unit is built.

A measurement is therefore three things at once: a number, a unit and an honest statement of how well the number is known. A student who times a pendulum and finds $g=9.6\ \text{m/s}^2$ has not "got it wrong" if the uncertainty of the experiment is $\pm0.3\ \text{m/s}^2$. In this chapter you will learn to read instruments to their least count, keep the right number of significant figures, check and even predict formulas with dimensions, convert units between systems, and carry errors through a calculation. In JEE Main these ideas are tested directly — Vernier and screw-gauge readings, dimensional formulas, the error in a calculated result — and they are quick marks for anyone who has practised them. They come back in Unit 20 (Experimental Skills) and in every numerical you will ever solve.

$Q=n\,u$→SI base units→Least count→Significant figures→Dimensions→Homogeneity→Unit conversion→Errors→$\tfrac{\Delta Z}{Z}=p\tfrac{\Delta A}{A}+\dots$
🎯 By the end of this chapter you can…
  • name the seven SI base quantities and units, tell fundamental from derived units, and use prefixes, the radian and steradian and practical units (light year, parsec, AU, electronvolt, kWh);
  • convert a quantity from one unit to another with factors of one;
  • find the least count of a Vernier calliper and a screw gauge and take a reading, including a zero correction;
  • count significant figures, keep the right number of them in sums, differences, products and quotients, and round off correctly;
  • write the dimensional formula of any mechanical quantity, use the principle of homogeneity to test an equation and to find the dimensions of an unknown constant;
  • deduce a relation by the method of dimensions, convert a numerical value between systems with $n_2=n_1\left[\tfrac{M_1}{M_2}\right]^a\left[\tfrac{L_1}{L_2}\right]^b\left[\tfrac{T_1}{T_2}\right]^c$, and say what the method cannot do;
  • tell systematic from random errors and find the mean value, mean absolute error, relative and percentage error of a set of readings;
  • find the maximum error in a sum, a difference, a product, a quotient and a power, and report a result as $\bar a\pm\Delta a$ with sensible digits;
  • solve JEE Main MCQ and numerical-answer problems on units, dimensions and errors.

A pendulum of length $L=100\ \text{cm}$ (scale least count $1\ \text{mm}$) is timed with a stopwatch of resolution $0.1\ \text{s}$. Timing a single oscillation gives $g$ with a maximum error of about $10\%$. If you time $N=20$ oscillations instead, the maximum percentage error in $g$ becomes about

Set $L=100\ \text{cm}$. With $N=1$ the stopwatch reads $t=2.0\ \text{s}$ and the readout shows a percentage error of $10.10\%$ (the result is $g=(10\pm1)\ \text{m/s}^2$). With $N=20$ it reads $t=40.1\ \text{s}$ and the error drops to $0.60\%$, giving $g=(9.82\pm0.06)\ \text{m/s}^2$. Since $g=\dfrac{4\pi^2L}{T^2}$, the error in $g$ is $\dfrac{\Delta L}{L}+2\dfrac{\Delta t}{t}$: the same $0.1\ \text{s}$ resolution is now spread over a $20$ times longer time, so the timing term falls from $10\%$ to $0.50\%$ — about 20 times, not 400 times. The length term ($0.10\%$) does not change.
Teaser — Measuring $g$ with a Pendulum

The formula $T=2\pi\sqrt{L/g}$ (its form follows from dimensions alone, Section 1.2) turns two measurements into a value of $g$. The length is read on a metre scale (least count $1\ \text{mm}$); the time for $N$ oscillations on a stopwatch that reads to $0.1\ \text{s}$. Choose $L$ and $N$ and press Play: the stopwatch runs while the bob swings $N$ times. The bars show how much each measurement adds to the percentage error in $g$ (Section 1.3), and the verdict writes the result with sensible digits (Section 1.1).

100 cm1
stopwatch reading $t$—
$g=4\pi^2L/T^2$ with $T=t/N$—
maximum error in $g$—

Sections in this chapter

🎯 Chapter mixed test JEE Main · MCQJEE Main · Numerical

Eight problems that mix all three sections, in no particular order — just as they come in the paper, where nothing tells you which idea a question needs. Answer each one and press Submit (NTA marking: $+4$ correct, $-1$ wrong, $0$ unanswered), or press ⏱ Take as a timed test for the real-exam experience: $8$ questions at the JEE Main pace of $2.4$ minutes each, with the NTA question palette.

E1. JEE Main · MCQ The force on a body varies with time as $F=\dfrac{a}{t}+bt^2$. The dimensions of $\dfrac{a}{b}$ are (A) $[\text{T}^{3}]$ (B) $[\text{T}^{-3}]$ (C) $[\text{M}\text{L}\text{T}^{-1}]$ (D) $[\text{T}]$

Homogeneity Each term has the dimensions of force, $[\text{M}\text{L}\text{T}^{-2}]$ (Principle 1.6).
Each constant $[a]=[F][t]=[\text{M}\text{L}\text{T}^{-1}]$; $\ [b]=\dfrac{[F]}{[t^2]}=[\text{M}\text{L}\text{T}^{-4}]$.
Answer (A) $\dfrac{[a]}{[b]}=[\text{T}^{3}]$.
⏱ Shortcut $a/t$ and $bt^2$ have the same dimensions, so $a/b$ has the dimensions of $t^2\cdot t=t^3$ — no need to write $[F]$ at all.

E2. JEE Main · Numerical The acceleration due to gravity is $9.8\ \text{m/s}^2$. Its value in $\text{km/h}^2$ is $N\times10^{3}\ \text{km/h}^2$. Find $N$. Give the answer to the nearest integer.

Factors of one $9.8\ \dfrac{\text{m}}{\text{s}^2}\times\dfrac{1\ \text{km}}{1000\ \text{m}}\times\left(\dfrac{3600\ \text{s}}{1\ \text{h}}\right)^2$ (Principle 1.1) — the factor for seconds is squared because $\text{s}$ appears squared.
Arithmetic $9.8\times10^{-3}\times1.296\times10^{7}=1.270\times10^{5}\ \text{km/h}^2=127.0\times10^{3}\ \text{km/h}^2$.
Answer $127$.
⏱ Shortcut $1\ \text{m/s}^2=\dfrac{3600^2}{1000}=12\,960\ \text{km/h}^2$; then $9.8\times12.96\approx127$. Forgetting to square $3600$ gives $35.3\ \text{km/h}^2$ — absurdly small, which is a quick warning sign.

E3. JEE Main · MCQ Five readings of the period of a pendulum are $2.04\ \text{s}$, $1.96\ \text{s}$, $2.02\ \text{s}$, $1.98\ \text{s}$ and $2.00\ \text{s}$. The percentage error, based on the mean absolute error, is (A) $0.6\%$ (B) $2.4\%$ (C) $1.2\%$ (D) $4.8\%$

Mean $\bar T=\dfrac{10.00}{5}=2.00\ \text{s}$.
Absolute errors $0.04,\ 0.04,\ 0.02,\ 0.02,\ 0$; mean absolute error $\Delta\bar T=\dfrac{0.12}{5}=0.024\ \text{s}$ (Definition 1.10).
Answer (C) $\dfrac{0.024}{2.00}\times100\%=1.2\%$.
⏱ Shortcut The readings are symmetric about $2.00$, so the mean is obvious; (B) and (D) come from using the largest deviation or forgetting to divide by $n$.

E4. JEE Main · Numerical In a Vernier calliper $20$ Vernier divisions coincide with $19$ main-scale divisions, and one main-scale division is $1\ \text{mm}$. The calliper has no zero error. For a thin rod the main scale reads $2\ \text{mm}$ and the $10$th Vernier division coincides with a main-scale mark. Taking the maximum error in the diameter to be one least count, find the maximum percentage error in the area of cross-section of the rod. Give the answer to the nearest integer.

Least count $\text{LC}=\dfrac{1\ \text{MSD}}{n}=\dfrac{1\ \text{mm}}{20}=0.05\ \text{mm}$ (Rule 1.2).
Reading $d=2\ \text{mm}+10\times0.05\ \text{mm}=2.50\ \text{mm}$, with $\Delta d=0.05\ \text{mm}$, i.e. $2\%$.
Power rule $A=\tfrac{\pi}{4}d^2$, so $\dfrac{\Delta A}{A}=2\dfrac{\Delta d}{d}=2\times2\%$ (Rule 1.11; $\pi/4$ is exact).
Answer $4$ (per cent).

E5. JEE Main · MCQ A strip of metal is measured to be $25.42\ \text{cm}$ long and $3.1\ \text{cm}$ wide. Its area, written with the correct number of significant figures, is (A) $78.802\ \text{cm}^2$ (B) $78.80\ \text{cm}^2$ (C) $78.8\ \text{cm}^2$ (D) $79\ \text{cm}^2$

Rule In a product the result keeps as many significant figures as the factor with the fewest (Rule 1.4): $3.1$ has two.
Round $25.42\times3.1=78.802$, rounded to two significant figures, is $79$.
Answer (D) $79\ \text{cm}^2$.
⏱ Shortcut (C) applies the decimal-places rule, which is for sums and differences only.

E6. JEE Main · Numerical The period $t$ of small oscillations of a liquid drop depends only on its radius $r$, the density $\rho$ of the liquid and its surface tension $S$ (dimensions $[\text{M}\text{T}^{-2}]$). Find how $t$ depends on $r$, $\rho$ and $S$ by the method of dimensions. If $r$, $\rho$ and $S$ are measured with maximum errors of $2\%$, $1\%$ and $3\%$, find the maximum percentage error in $t$. Give the answer to the nearest integer.

Dimensions Put $t=k\,r^a\rho^bS^c$: $[\text{T}]=[\text{L}]^a[\text{M}\text{L}^{-3}]^b[\text{M}\text{T}^{-2}]^c$.
Solve $\text{M}$: $b+c=0$; $\ \text{T}$: $-2c=1$; $\ \text{L}$: $a-3b=0$. So $c=-\tfrac12$, $b=\tfrac12$, $a=\tfrac32$, and $t=k\sqrt{\dfrac{\rho r^3}{S}}$.
Errors $\dfrac{\Delta t}{t}=\tfrac32\dfrac{\Delta r}{r}+\tfrac12\dfrac{\Delta\rho}{\rho}+\tfrac12\dfrac{\Delta S}{S}=3\%+0.5\%+1.5\%$ — the powers enter as magnitudes, even the negative one.
Answer $5$ (per cent).

E7. JEE Main · MCQ The kinetic energy of a body is found from its momentum $p$ and mass $m$ as $K=\dfrac{p^2}{2m}$. If $p$ is measured with a maximum error of $2\%$ and $m$ with $1\%$, the maximum error in $K$ is (A) $3\%$ (B) $5\%$ (C) $4\%$ (D) $1\%$

Rule $\dfrac{\Delta K}{K}=2\dfrac{\Delta p}{p}+\dfrac{\Delta m}{m}$ (Rule 1.11); the factor $2$ in the denominator is exact and adds no error.
Answer (B) $2\times2\%+1\%=5\%$.
⏱ Shortcut (D) subtracts the error of the quotient — errors never cancel when we want the maximum error.

E8. JEE Main · Numerical In a new system of units the unit of mass is $5\ \text{kg}$, the unit of length is $2\ \text{m}$ and the unit of time is $2\ \text{s}$. What is the numerical value of a force of $50\ \text{N}$ in this system? Give the answer to the nearest integer.

Conversion Force is $[\text{M}\text{L}\text{T}^{-2}]$, so (Principle 1.8) $n_2=n_1\left[\dfrac{M_1}{M_2}\right]\left[\dfrac{L_1}{L_2}\right]\left[\dfrac{T_1}{T_2}\right]^{-2}$.
Numbers $n_2=50\times\dfrac15\times\dfrac12\times\left(\dfrac12\right)^{-2}=50\times\dfrac{1}{10}\times4=20$.
Answer $20$.
⏱ Shortcut Build the new unit directly: $1\ \text{new unit}=\dfrac{5\times2}{2^2}=2.5\ \text{N}$, and $\dfrac{50}{2.5}=20$.
✅ Before you start
This is the first chapter of the course, so it needs only Class 10 science and mathematics: powers of ten and scientific notation, the laws of exponents (including fractional and negative powers), solving three simultaneous linear equations (for the method of dimensions), percentages, and the area of a circle and the volume of a sphere. From Class 10 Science, recall that speed, force, energy and power have units built from the metre, kilogram and second. If you have not yet read the welcome page, start there: it explains how the quick checks, predictions, speed drills and Exam corners in every section work.