Chapter 19 · Introduction

Chapter 19 — Electronic Devices

A few impurity atoms per million turn silicon into n-type or p-type material; join the two and you get a p–n junction that lets current pass one way only. That one-way valve becomes rectifiers, LEDs, photodiodes, solar cells and voltage regulators — and switching circuits that compute with 0s and 1s through logic gates.

A phone charger, an LED bulb, the solar panel on a roof and the processor inside a laptop look nothing alike, yet they are all built from the same material: silicon, purified to one foreign atom in a billion and then deliberately "spoiled" with a few atoms of phosphorus or boron per million. That tiny amount of impurity raises the conductivity of silicon tens of thousands of times and decides whether the current is carried by electrons or by holes. Put a p-type layer against an n-type layer and you have the most important device of the twentieth century — the p–n junction diode, a one-way valve for electric current. India's solar parks, the $230\ \text{V}$-to-$5\ \text{V}$ adapter on every desk and the white LEDs that replaced filament bulbs all rest on how such a junction behaves.

This chapter builds the story in three steps. First, semiconductors: energy bands and the band gap separate conductors, insulators and semiconductors; electrons and holes carry current; doping makes n-type and p-type material obeying the mass-action law $n_en_h=n_i^2$; and a p–n junction forms a depletion layer and a barrier potential that make its I–V characteristic one-sided. Second, diode circuits: with the ideal or $0.7\ \text{V}$ model you can solve any circuit with diodes, build half-wave and full-wave rectifiers, and use the special diodes — the LED, the photodiode, the solar cell and the Zener diode as a voltage regulator. Third, logic gates: OR, AND, NOT, NAND and NOR, their truth tables and waveforms, De Morgan's theorems, and why NAND or NOR alone can build every other gate. JEE Main has one or two questions on this chapter in nearly every shift — often the quickest marks on the paper.

Energy bands, $E_g$→Electrons & holes→Doping: $n_en_h=n_i^2$→p–n junction, barrier→Forward & reverse bias→Rectifier→LED, photodiode, solar cell→Zener regulator→OR, AND, NOT→NAND, NOR: universal
🎯 By the end of this chapter you can…
  • classify solids as conductors, insulators and semiconductors from their energy bands, and use the band gap with $hc=1240\ \text{eV nm}$;
  • explain intrinsic and extrinsic (n-type and p-type) semiconductors, use the mass-action law $n_en_h=n_i^2$, and find conductivity from $\sigma=e(n_e\mu_e+n_h\mu_h)$;
  • explain the depletion layer and barrier potential of a p–n junction, and how forward and reverse bias change them;
  • draw and read the I–V characteristic of a diode, and find its static and dynamic resistance;
  • solve circuits with ideal diodes and with the $0.7\ \text{V}$ model, and find the output peak, frequency and average value of half-wave and full-wave rectifiers;
  • explain the working and I–V characteristics of the LED, the photodiode and the solar cell, and which bias each one uses;
  • analyse a Zener voltage regulator: decide whether it regulates, and find the series, load and Zener currents;
  • write the truth tables and Boolean expressions of OR, AND, NOT, NAND and NOR gates, draw output waveforms, use De Morgan's theorems and identify the single gate equivalent to a combination;
  • solve JEE Main MCQ and numerical-answer problems on semiconductors, diode circuits and logic gates.

Two silicon diodes (each $0.7\ \text{V}$ when conducting) have their anodes connected to inputs A and B and their cathodes joined to an output that is connected to earth through a $1\ \text{k}\Omega$ resistor. Input A is at $5\ \text{V}$ and input B at $0\ \text{V}$. What is the output?

Choose the OR circuit and set $A=5\ \text{V}$, $B=0\ \text{V}$. The readouts show D1 forward, D2 reverse, $V_\text{out}=4.3\ \text{V}$ and a current of $4.3\ \text{mA}$ in the resistor, so the output is logic $1$. Diode A conducts and holds the output $0.7\ \text{V}$ below its input (the $0.7\ \text{V}$ model of Section 19.2); diode B then has $0\ \text{V}$ on its anode and $4.3\ \text{V}$ on its cathode — reverse biased, an open switch (Section 19.1). Try all four input pairs: the output is high if A or B is high — an OR gate (Section 19.3). Then switch to the AND circuit, where the diodes are reversed and the resistor goes to $+5\ \text{V}$: now the output is high only when both inputs are high.
Teaser — Logic Gates Made of Diodes

Two silicon diodes and one $1\ \text{k}\Omega$ resistor make a logic gate. Each input is either $0\ \text{V}$ (logic $0$) or $5\ \text{V}$ (logic $1$); an output above $2.5\ \text{V}$ counts as logic $1$. Choose the circuit, click the input buttons, and see which diode is forward biased (green, carrying current) and which is reverse biased (grey). Press Play to see the current flow.

diode D1 (from A)—
diode D2 (from B)—
output voltage, current in R—
logic output Y—

Sections in this chapter

🎯 Chapter mixed test JEE Main · MCQJEE Main · Numerical

Eight problems drawn from all three sections and shuffled, as in the real paper; some need a property of the junction from one section and a circuit from another. Answer each one and press Submit (NTA marking: $+4$ correct, $-1$ wrong, $0$ unanswered), or press ⏱ Take as a timed test for the real-exam experience: $8$ questions at the JEE Main pace of $2.4$ minutes each, with the NTA question palette. Take $e=1.6\times10^{-19}\ \text{C}$.

E1. JEE Main · MCQ A crystal of pure silicon is doped with a small amount of gallium, an element of group 13. The doped crystal is (A) n-type, with a net negative charge (B) p-type, and electrically neutral (C) p-type, with a net positive charge (D) n-type, and electrically neutral

Type Gallium has three valence electrons, one short of silicon's four, so each gallium atom accepts an electron and leaves a hole: an acceptor, giving p-type material with holes as majority carriers (Section 19.1).
Charge Every atom added is neutral, so the crystal as a whole stays neutral; each mobile hole is balanced by a fixed negative acceptor ion.
Answer (B).
⏱ Shortcut Group 15 (P, As, Sb) ⇒ donors ⇒ n-type; group 13 (B, Al, Ga, In) ⇒ acceptors ⇒ p-type. Doped crystals are never charged — "p" and "n" name the majority carriers, not the net charge.

E2. JEE Main · Numerical A Zener diode of breakdown voltage $10\ \text{V}$ is connected in series with a $250\ \Omega$ resistor across a $15\ \text{V}$ d.c. supply, and a $2.0\ \text{k}\Omega$ load is connected in parallel with the Zener. Find the current through the Zener diode, in mA. Give the answer to the nearest integer.

Check breakdown Without the Zener the load would get $\dfrac{15\times2000}{2250}=13.3\ \text{V}\gt10\ \text{V}$, so the Zener conducts and holds $V_L=10\ \text{V}$ (Section 19.2).
Currents $I_s=\dfrac{15-10}{250}=20\ \text{mA}$, $I_L=\dfrac{10}{2000}=5\ \text{mA}$, so $I_Z=I_s-I_L=15\ \text{mA}$.
Answer $15$.
⏱ Shortcut Series resistor: $(V_{in}-V_Z)/R_s$; load: $V_Z/R_L$; Zener: the difference. Always check first that the Zener is really in breakdown.

E3. JEE Main · MCQ The Boolean expression $Y=\overline{\overline{A}+\overline{B}}$ describes (A) an OR gate (B) a NAND gate (C) an AND gate (D) a NOR gate

De Morgan $\overline{X+Y}=\overline{X}\cdot\overline{Y}$ (Section 19.3), so $Y=\overline{\overline{A}}\cdot\overline{\overline{B}}=A\cdot B$.
Check $Y=1$ only when $\overline A=\overline B=0$, i.e. $A=B=1$ — the AND truth table.
Answer (C).
⏱ Shortcut "Break the bar, change the sign": a NOR of the inverted inputs is an AND. In the same way a NAND of the inverted inputs is an OR.

E4. JEE Main · Numerical A $9.0\ \text{V}$ battery is connected in series with a $400\ \Omega$ resistor, a silicon diode and a germanium diode, both forward biased. Using the constant-voltage-drop model with the usual knee voltages of the two materials, find the current in the circuit, in mA. Give the answer to the nearest integer.

Knee voltages Silicon $0.7\ \text{V}$, germanium $0.3\ \text{V}$ (Section 19.1).
Loop In the $0.7\ \text{V}$ model each conducting diode is a fixed drop (Section 19.2): $9.0-0.7-0.3=I\times400$, so $I=\dfrac{8.0}{400}=0.020\ \text{A}$.
Answer $20\ \text{mA}$, i.e. $20$.
⏱ Shortcut Subtract the diode drops from the emf, then use Ohm's law. With ideal diodes the answer would be $22.5\ \text{mA}$ — read which model the problem wants.

E5. JEE Main · MCQ A bridge rectifier made of four silicon diodes (each $0.7\ \text{V}$ when conducting) is fed from a $50\ \text{Hz}$ sinusoidal supply of peak value $12\ \text{V}$ and drives a resistive load. The peak voltage across the load and the frequency of the output are (A) $12\ \text{V}$, $50\ \text{Hz}$ (B) $11.3\ \text{V}$, $100\ \text{Hz}$ (C) $10.6\ \text{V}$, $50\ \text{Hz}$ (D) $10.6\ \text{V}$, $100\ \text{Hz}$

Peak In a bridge, two diodes are in the current path in each half-cycle (Section 19.2): $V_\text{out,peak}=12-2(0.7)=10.6\ \text{V}$.
Frequency Both half-cycles give a positive pulse, so there are two pulses per input cycle: $2\times50=100\ \text{Hz}$.
Answer (D).
⏱ Shortcut Bridge: subtract $1.4\ \text{V}$; centre-tap: $0.7\ \text{V}$ (but the PIV is doubled). Full-wave always doubles the frequency. (B) counts only one diode.

E6. JEE Main · Numerical A silicon sample is doped so that its electron concentration is $5.0\times10^{21}\ \text{m}^{-3}$. The intrinsic carrier concentration is $1.5\times10^{16}\ \text{m}^{-3}$, and the electron and hole mobilities are $0.15$ and $0.050\ \text{m}^2\text{V}^{-1}\text{s}^{-1}$. Find the conductivity of the sample in $\text{S/m}$ ($\Omega^{-1}\text{m}^{-1}$). Give the answer to the nearest integer.

Holes Mass-action law (Section 19.1): $n_h=\dfrac{n_i^2}{n_e}=\dfrac{(1.5\times10^{16})^2}{5.0\times10^{21}}=4.5\times10^{10}\ \text{m}^{-3}$ — utterly negligible.
Conductivity $\sigma=e(n_e\mu_e+n_h\mu_h)\approx1.6\times10^{-19}\times5.0\times10^{21}\times0.15=120\ \text{S/m}$.
Answer $120$.
⏱ Shortcut In a doped sample only the majority carriers count: $\sigma\approx en_\text{maj}\mu_\text{maj}$. The resistivity is $1/120=8.3\times10^{-3}\ \Omega\,\text{m}$.

E7. JEE Main · MCQ Inputs $A$ and $B$ feed a NAND gate, whose output is $P$. Input $A$ also passes through a NOT gate, whose output is $Q$. $P$ and $Q$ are the inputs of a second NAND gate, whose output is $Y$. Then (A) $Y=A$ (B) $Y=B$ (C) $Y=A\cdot B$ (D) $Y=A+B$

Expressions $P=\overline{A\cdot B}$, $Q=\overline{A}$, so $Y=\overline{P\cdot Q}=\overline{P}+\overline{Q}=A\cdot B+A$ (De Morgan, Section 19.3).
Simplify $A\cdot B+A=A\cdot(B+1)=A\cdot1=A$.
Answer (A). (Truth table: $AB=00,01,10,11$ give $Y=0,0,1,1$.)
⏱ Shortcut Try $A=0$: $Q=1$, $P=1$, so $Y=0$. Try $A=1$: $Q=0$, so the second NAND outputs $1$ whatever $P$ is. $Y$ follows $A$ and ignores $B$.

E8. JEE Main · Numerical A half-wave rectifier with an ideal diode and a resistive load (no filter) is connected to a $220\ \text{V}$ (rms), $50\ \text{Hz}$ supply. Find the average (d.c.) value of the output voltage, in volts. Give the answer to the nearest integer.

Peak $V_m=\sqrt2\times220=311\ \text{V}$.
Average Half-wave output averages $\dfrac{V_m}{\pi}$ over a full cycle (Section 19.2): $\dfrac{311.1}{\pi}=99.0\ \text{V}$.
Answer $99$.
⏱ Shortcut $\dfrac{\sqrt2}{\pi}=0.45$: half-wave d.c. $\approx0.45\,V_\text{rms}$, full-wave $\approx0.90\,V_\text{rms}$. Using $220\ \text{V}$ as the peak is the classic slip ($70\ \text{V}$).
✅ Before you start
Semiconductors extend the ideas of current, drift velocity, mobility and resistivity (Section 12.1), and diode circuits are solved with Kirchhoff's laws (Section 12.2). The barrier of a junction is an electric field and a potential difference (Section 11.3). Rectifiers start from an alternating supply, so recall peak and rms values (Section 14.3). LEDs, photodiodes and solar cells exchange photons with the crystal, $E=hc/\lambda$ (Section 17.1), and energy bands grow out of the discrete energy levels of single atoms (Section 18.2). Logic gates need no physics at all — only careful bookkeeping with $0$ and $1$.