Chapter 12 · Current Electricity

12.1 Electric Current, Drift Velocity and Ohm's Law

A current is charge flowing past a point each second. Inside a metal it is carried by free electrons that drift along the wire at a fraction of a millimetre per second, giving $I=neAv_d$; from that slow drift come Ohm's law, the resistance $R=\rho L/A$, its rise with temperature and the power $P=VI$ that a current delivers.

Press a switch and a lamp across the room lights at once. It is tempting to imagine electrons racing from the switch to the lamp, but they do nothing of the sort: in a household wire the free electrons creep along at less than a millimetre per second, and an electron that enters the wire at the switch would take hours to reach the lamp. What travels fast is the electric field that pushes them, set up throughout the circuit almost at the speed of light; every free electron in the wire starts drifting at once, so the current starts everywhere at once.

This section builds current electricity from that picture. We define current and current density, follow an electron in a metal as it is accelerated by the field and knocked about by collisions with the ions, and get the drift velocity, the mobility and the key link $I=neAv_d$. From the same picture comes Ohm's law and the resistance $R=\rho L/A$ of a wire, the shapes of the V–I graphs of ohmic and non-ohmic devices, the way resistance changes with temperature, and the energy and power delivered by a current — the ideas every later problem in this chapter uses.

Electric current and current density

Charge can flow wherever there are charge carriers free to move: free electrons in a metal, positive and negative ions in a salt solution or a gas discharge, electrons and holes in a semiconductor. When there is a net flow of charge across a surface, there is an electric current through it.

📘 Definition 12.1 — Electric current

If a net charge $\Delta q$ crosses a cross-section of a conductor in a time $\Delta t$, the average current is $\bar I=\Delta q/\Delta t$. The current at an instant is the rate of flow of charge,

$$I=\frac{dq}{dt}.$$

Its SI unit is the ampere: $1\ \text{A}=1\ \text{C/s}$ (the ampere is an SI base unit; the coulomb is derived from it). A current is called steady if it does not change with time. By convention the direction of a current is the direction in which positive charge flows; in a metal the electrons move the opposite way.

Three practical points follow from the definition.

Any charge going round a circle is also a current. A charge $q$ making $f$ revolutions per second carries charge $q$ past any point on its path $f$ times a second, so it is equivalent to a current $I=qf=\dfrac{q\omega}{2\pi}$. This is how an electron orbiting a nucleus, or a charged ring spinning about its axis, becomes a tiny current loop (Unit 13).

To describe how current is spread over a cross-section we use a quantity defined at each point.

📘 Definition 12.2 — Current density

The current density $\mathbf j$ at a point is a vector in the direction of the current there, whose magnitude is the current per unit area through a small area $\Delta A$ placed perpendicular to the flow:

$$j=\frac{\Delta I}{\Delta A}\qquad(\text{SI unit } \text{A/m}^2).$$

If the area is tilted so that its normal makes an angle $\theta$ with $\mathbf j$, the current through it is $\Delta I=j\,\Delta A\cos\theta=\mathbf j\cdot\Delta\mathbf A$. For a current spread uniformly over the cross-section $A$ of a wire, $j=I/A$.

Current density is the "local" quantity. In a wire whose thickness changes, the current $I$ is the same at every cross-section (charge cannot pile up anywhere in a steady state), but $j=I/A$ is larger where the wire is thinner. If $j$ varies across the section — say with the distance $r$ from the axis — the current is found by adding up rings: $I=\displaystyle\int_0^R j(r)\,2\pi r\,dr$.

✏️ Example 1 — Counting the charge
(a) $3.0\times10^{20}$ electrons pass a cross-section of a wire in $12\ \text{s}$. Find the current. (b) In a salt solution, $2.0\times10^{18}$ $\text{Na}^+$ ions move to the right and $1.5\times10^{18}$ $\text{Cl}^-$ ions move to the left through a cross-section every second. Find the current and its direction. (c) The charge that has passed a point in a circuit is $q=(2t^2+3t)\ \text{C}$, with $t$ in seconds. Find the current at $t=2.0\ \text{s}$ and the average current over the first $2.0\ \text{s}$. (d) A current rises steadily from $0$ to $6.0\ \text{A}$ in $4.0\ \text{s}$ and then falls steadily to zero in the next $2.0\ \text{s}$. How much charge flows, and how many electrons is that? (e) In a simple model of the hydrogen atom an electron goes round the nucleus $6.6\times10^{15}$ times a second. Find the equivalent current.
(a) $I=\dfrac{Ne}{t}=\dfrac{3.0\times10^{20}\times1.6\times10^{-19}}{12}=\dfrac{48}{12}=4.0\ \text{A}$, opposite to the motion of the electrons.
(b) Both kinds of ion carry current to the right: $I=(2.0+1.5)\times10^{18}\times1.6\times10^{-19}=0.56\ \text{A}$, to the right.
(c) $I=\dfrac{dq}{dt}=4t+3=11\ \text{A}$ at $t=2.0\ \text{s}$. Average: $\bar I=\dfrac{q(2)-q(0)}{2.0}=\dfrac{14}{2.0}=7.0\ \text{A}$ — not the same as the instantaneous value, because the current is changing.
(d) Area of the triangle under the $I$–$t$ graph: $q=\tfrac12\times6.0\ \text{s}\times6.0\ \text{A}=18\ \text{C}$; $N=\dfrac{18}{1.6\times10^{-19}}=1.1\times10^{20}$ electrons.
(e) $I=ef=1.6\times10^{-19}\times6.6\times10^{15}=1.06\times10^{-3}\ \text{A}\approx1.1\ \text{mA}$.
Check Units in (c): $q$ in coulombs, $t$ in seconds, so $dq/dt$ is in $\text{C/s}=\text{A}$ ✓.

In a gas discharge tube, every second $3.0\times10^{18}$ positive ions (charge $+e$) move to the right and $3.0\times10^{18}$ electrons move to the left across a cross-section. The current is

Drift velocity and mobility

A metal is a lattice of positive ions with roughly one to three electrons per atom that are not tied to any ion — the free electrons, about $10^{28}$–$10^{29}$ of them per cubic metre. Even with no field they are far from still: they rush about in random directions with speeds of the order of $10^5$–$10^6\ \text{m/s}$, colliding with the vibrating ions and changing direction after each collision. Because their directions are random, the average velocity of all the free electrons is zero, and as many cross any section one way as the other: no current.

Now apply a field $\mathbf E$ along the wire. Between collisions each electron feels a force $-e\mathbf E$ and an acceleration $\mathbf a=-e\mathbf E/m$. An electron that had velocity $\mathbf u_i$ just after its last collision, a time $t_i$ ago, now has velocity

$$\mathbf v_i=\mathbf u_i-\frac{e\mathbf E}{m}\,t_i .$$

Average this over all the free electrons at one instant. The velocities $\mathbf u_i$ just after collisions point in random directions, so they average to zero; the times $t_i$ since the last collision average to a characteristic time $\tau$, the relaxation time. What is left is a small, steady average velocity opposite to $\mathbf E$ — superimposed on the much faster random motion. Each collision "wipes out" the extra velocity gained from the field, so it cannot build up without limit.

📘 Definition 12.3 — Relaxation time and drift velocity

The relaxation time $\tau$ of a conductor is the average time between successive collisions of a free electron with the ions (about $10^{-14}\ \text{s}$ in metals at room temperature). The drift velocity $\mathbf v_d$ is the average velocity acquired by the free electrons under the applied field:

$$\mathbf v_d=-\frac{e\tau}{m}\,\mathbf E,\qquad v_d=\frac{eE\tau}{m}.$$

It is directed opposite to $\mathbf E$ (and so opposite to the conventional current), and in metals it is typically a fraction of a millimetre per second.

📘 Definition 12.4 — Mobility

The mobility $\mu$ of a charge carrier is the magnitude of its drift velocity per unit electric field:

$$\mu=\frac{v_d}{E}=\frac{e\tau}{m}.$$

Its SI unit is $\text{m}^2\,\text{V}^{-1}\text{s}^{-1}$ (from $\text{(m/s)/(V/m)}$). Mobility is positive for both electrons and holes; it is large when collisions are rare (long $\tau$) and the carrier is light.

Relating the drift to the current. Consider a wire of cross-section $A$ containing $n$ free electrons per unit volume, all drifting with speed $v_d$. In a time $\Delta t$ each electron moves a distance $v_d\Delta t$, so every electron in a length $v_d\Delta t$ of the wire — a volume $Av_d\Delta t$ — crosses a chosen section. The charge crossing is $\Delta q=(nAv_d\Delta t)\,e$.

📐 Result 12.1 — Current and drift velocity

For carriers of charge $e$ and number density $n$ drifting with speed $v_d$ through a cross-section of area $A$,

$$I=neAv_d,\qquad j=nev_d .$$

In a steady current the same $I$ flows through every section of a wire, so in a wire of varying thickness (same material, same $n$) $v_d\propto1/A$: the electrons drift faster where the wire is thinner.

Put $v_d=eE\tau/m$ into $j=nev_d$ and something remarkable appears: the current density is proportional to the field,

$$j=\frac{ne^2\tau}{m}\,E .$$
📐 Result 12.2 — Ohm's law in microscopic form

In a conductor in which $n$ and $\tau$ do not depend on the field (a metal at a fixed temperature),

$$\mathbf j=\sigma\mathbf E,\qquad \sigma=\frac{ne^2\tau}{m}=ne\mu ,\qquad \rho=\frac1\sigma=\frac{m}{ne^2\tau}.$$

$\sigma$ is the conductivity and $\rho$ the resistivity of the material (Definition 12.6). They depend only on the material ($n$) and its state ($\tau$, which changes with temperature) — not on the size or shape of the sample. If both electrons and holes carry current (a semiconductor), $\sigma=e(n_e\mu_e+n_h\mu_h)$.

Notice what this does and does not say. The drift speed is tiny, $v_d\sim10^{-4}\ \text{m/s}$, while the random speed is $10^5$ times larger — so the field barely disturbs the random motion, which is why $\tau$ does not depend on $E$ and the law is linear. And although each electron crawls, the current is set up almost instantly round the whole circuit, because the field travels through the wire at close to the speed of light and starts all the electrons drifting together. A long wire is like a pipe already full of water: push at one end and water comes out of the other end at once.

🧭 Problem-solving strategy — Drift-speed and current problems
  1. Decide what is held fixed. Same wire carrying a given current: use $v_d=\dfrac{I}{neA}$. Given voltage across a uniform wire: use $E=V/L$ and $v_d=\mu E=\dfrac{e\tau}{m}\dfrac VL$.
  2. Convert to SI first: $\text{mm}^2=10^{-6}\ \text{m}^2$, a diameter $d$ gives $A=\pi d^2/4$.
  3. Link the microscopic and the measurable with $j=nev_d=\sigma E$, $\ \sigma=ne\mu=\dfrac{ne^2\tau}{m}=\dfrac1\rho$.
  4. For parts of a conductor in series the current is common, so $v_d$, $j$ and $E$ all scale as $1/A$.
✏️ Example 2 — How slowly do electrons drift?
A copper wire of diameter $1.0\ \text{mm}$ carries a current of $3.0\ \text{A}$. Copper has $8.5\times10^{28}$ free electrons per cubic metre and resistivity $1.7\times10^{-8}\ \Omega\,\text{m}$. Find (a) the drift speed of the electrons; (b) the time an electron takes to drift $2.0\ \text{m}$ along the wire; (c) the electric field in the wire, the mobility of the electrons and their relaxation time.
Find the drift speed in (a) before you open the solution:
(a) $A=\pi(0.50\times10^{-3})^2=7.85\times10^{-7}\ \text{m}^2$. $\ v_d=\dfrac{I}{neA}=\dfrac{3.0}{8.5\times10^{28}\times1.6\times10^{-19}\times7.85\times10^{-7}}=2.81\times10^{-4}\ \text{m/s}=0.281\ \text{mm/s}$.
(b) $t=\dfrac{2.0}{2.81\times10^{-4}}=7.1\times10^{3}\ \text{s}$ — about two hours to cross a room.
(c) $j=\dfrac{I}{A}=3.82\times10^6\ \text{A/m}^2$, $\ E=\rho j=1.7\times10^{-8}\times3.82\times10^6=0.065\ \text{V/m}$. Mobility $\mu=\dfrac{v_d}{E}=\dfrac{2.81\times10^{-4}}{0.0649}=4.3\times10^{-3}\ \text{m}^2\,\text{V}^{-1}\text{s}^{-1}$. Relaxation time $\tau=\dfrac{m\mu}{e}=\dfrac{9.1\times10^{-31}\times4.33\times10^{-3}}{1.6\times10^{-19}}=2.5\times10^{-14}\ \text{s}$.
Check $\tau=\dfrac{m}{ne^2\rho}=\dfrac{9.1\times10^{-31}}{8.5\times10^{28}\times(1.6\times10^{-19})^2\times1.7\times10^{-8}}=2.5\times10^{-14}\ \text{s}$ ✓ — the same answer straight from Result 12.2.
✏️ Example 3 — A wire that narrows
A copper conductor is made of two cylindrical parts of equal length joined end to end: part P has radius $2r$ and part Q has radius $r$. A steady current flows through it, and the drift speed of the electrons in Q is $0.40\ \text{mm/s}$. (a) Find the drift speed in P. (b) Find the ratios of the current densities and of the electric fields in Q and P. (c) What fraction of the total potential difference across the conductor appears across Q? (d) Show that if a fixed potential difference $V$ is applied across a single uniform copper wire of length $L$, the drift speed does not depend on the wire's thickness.
Find the fraction in (c) first:
(a) The same $I$ flows through both parts and $n$ is the same, so $v_d\propto\dfrac1A\propto\dfrac1{r^2}$. P has four times the area: $v_P=\dfrac{0.40}{4}=0.10\ \text{mm/s}$.
(b) $j=I/A$: $\ j_Q:j_P=4:1$. Since $E=\rho j$ with the same $\rho$, $\ E_Q:E_P=4:1$ — the field is concentrated in the thin part.
(c) Over equal lengths $V=E\ell$, so $V_Q:V_P=4:1$ and $V_Q=\tfrac45V=0.80\,V$.
(d) $E=V/L$, so $v_d=\mu E=\dfrac{\mu V}{L}$: it depends on $V$, $L$ and the material only. A thicker wire carries more current, $I=neAv_d$, because it has more electrons drifting — not because they drift faster.
⏱ Shortcut Same current ⇒ $v_d\propto1/A$; same voltage across one wire ⇒ $v_d\propto V/L$, independent of $A$. Decide first which is fixed.

In Interactive 1 choose copper, a current of $2.0\ \text{A}$ and a cross-section of $1.0\ \text{mm}^2$, and read the drift speed. Then double the cross-section to $2.0\ \text{mm}^2$, keeping the current at $2.0\ \text{A}$. What happens to the drift speed?

With $I=2.0\ \text{A}$ and $A=1.0\ \text{mm}^2$ the readouts show $j=2.00\times10^6\ \text{A/m}^2$, $v_d=0.147\ \text{mm/s}$, $E=0.034\ \text{V/m}$ and about $1.89\ \text{h}$ to drift $1\ \text{m}$. At $A=2.0\ \text{mm}^2$: $v_d=0.0735\ \text{mm/s}$, $E=0.017\ \text{V/m}$, $3.78\ \text{h}$. The current is fixed, so $v_d=I/(neA)$ halves when $A$ doubles — the same charge per second is carried by twice as many electrons. (A quarter would be $1/A^2$, as for a doubled diameter.) Notice how little the swarm moves compared with the electrons' random jiggling.
Interactive 1 — Free Electrons Drifting in a Wire

Free electrons (blue) dart about between the fixed ions, changing direction at every collision. The field in the wire adds a tiny steady drift to the left, against the field — follow the dashed marker, which moves at the drift speed (drawn hugely magnified; the random motion is slowed down even more). Choose the metal, the current and the cross-section, and compare the speeds on the scale below.

2.0 A1.00 mm²
current density $j$—
drift speed $v_d$—
field $E=\rho j$—
time to drift 1 m—

A potential difference $V$ is kept across a copper wire of length $L$ and diameter $d$. Which single change doubles the drift speed of the free electrons?

Ohm's law, resistance and resistivity

For a whole wire of length $L$ and cross-section $A$, Result 12.2 turns into a statement about the measurable quantities $V$ and $I$. The field in a uniform wire is $E=V/L$ and the current density is $j=I/A$; then $j=\sigma E$ reads $I/A=V/(\rho L)$, that is, $V=\left(\dfrac{\rho L}{A}\right)I$. The potential difference is proportional to the current — the law Georg Ohm found by experiment in 1827.

📐 Law 12.3 — Ohm's law

The current through a metallic conductor is proportional to the potential difference across it, provided its temperature and other physical conditions (strain, illumination…) stay the same:

$$V=IR ,$$

where the constant $R$ is the resistance of the conductor.

📘 Definition 12.5 — Resistance and conductance

The resistance of a conductor is the ratio of the potential difference across it to the current through it, $R=V/I$. Its SI unit is the ohm, $1\ \Omega=1\ \text{V/A}$; dimensions $[\text{ML}^2\text{T}^{-3}\text{A}^{-2}]$. The reciprocal $G=1/R$ is the conductance, measured in siemens ($1\ \text{S}=1\ \Omega^{-1}$).

📘 Definition 12.6 — Resistivity and conductivity

The resistivity $\rho$ of a material is the resistance of a sample of unit length and unit cross-sectional area; the conductivity is $\sigma=1/\rho$. For a uniform conductor of length $L$ and cross-section $A$, with the current along its length,

$$R=\frac{\rho L}{A}.$$

SI units: $\rho$ in $\Omega\,\text{m}$, $\sigma$ in $\text{S/m}$ (or $\Omega^{-1}\text{m}^{-1}$). Resistivity depends on the material and its temperature, not on the sample's dimensions.

Typical resistivities at room temperature span more than twenty powers of ten: silver $1.6\times10^{-8}$, copper $1.7\times10^{-8}$, aluminium $2.7\times10^{-8}$, nichrome about $1.1\times10^{-6}$, pure germanium about $0.5$, pure silicon about $2\times10^3$, glass $10^{10}$–$10^{14}$, quartz about $10^{16}\ \Omega\,\text{m}$. Conductors, semiconductors and insulators sit in clearly separated ranges.

Reshaping a wire. When a wire is stretched or drawn through a die, its volume $V_0=AL$ stays the same while $L$ and $A$ change. Then

$$R=\frac{\rho L}{A}=\frac{\rho L^2}{V_0}=\frac{\rho V_0}{A^2}\ \Rightarrow\ R\propto L^2\propto\frac1{A^2}\propto\frac1{r^4}.$$

Stretching a wire to $k$ times its length makes its resistance $k^2$ times larger; reducing its radius by half makes it $16$ times larger. For a small stretch, $\dfrac{\Delta R}{R}\approx2\dfrac{\Delta L}{L}$. For a rectangular block the rule is the same, $R=\rho\,(\text{length along the current})/(\text{area across it})$, so the resistance depends on which pair of faces the current enters and leaves by.

V–I characteristics. A graph of $I$ against $V$ for a device is called its V–I (or I–V) characteristic, and it tells at a glance whether Ohm's law holds.

📘 Definition 12.7 — Ohmic and non-ohmic conductors

A conductor is ohmic if its V–I characteristic is a straight line through the origin, the same for both directions of current, so that $R=V/I$ is constant (metals and alloys at a fixed temperature). It is non-ohmic if the characteristic departs from this, for example when

  • the graph is curved — a filament lamp, whose resistance rises as it heats up;
  • the current depends on the direction of $V$ — a semiconductor diode conducts readily one way and hardly at all the other way;
  • the relation is not single-valued — in some materials (gallium arsenide) the same current flows at more than one voltage, and part of the curve has negative slope.

For a non-ohmic device we can still quote the static resistance $V/I$ at a working point, and the dynamic resistance $r_d=dV/dI$ (the reciprocal of the slope of the I–V graph there); for an ohmic conductor the two are equal.

On an I–V graph the slope of a straight line through the origin is $I/V=1/R$: a steeper line means a smaller resistance. If the graph is drawn the other way, $V$ against $I$, the slope is $R$ itself. JEE Main often shows two straight lines for the same wire at two temperatures, or for two wires, and asks which has the larger resistance — always check which quantity is on which axis.

✏️ Example 4 — Stretching a wire and choosing faces
(a) Find the resistance of a nichrome wire ($\rho=1.1\times10^{-6}\ \Omega\,\text{m}$) of length $2.0\ \text{m}$ and diameter $0.40\ \text{mm}$. (b) The wire is stretched uniformly to a length of $3.0\ \text{m}$. Find its new resistance. (c) A different wire is drawn out until its radius is $10\%$ smaller. By what percentage does its resistance increase? (d) A copper block measures $1.0\ \text{cm}\times2.0\ \text{cm}\times4.0\ \text{cm}$. Find the ratio of the largest to the smallest resistance between a pair of opposite faces.
(a) $A=\pi(0.20\times10^{-3})^2=1.257\times10^{-7}\ \text{m}^2$; $\ R=\dfrac{\rho L}{A}=\dfrac{1.1\times10^{-6}\times2.0}{1.257\times10^{-7}}=17.5\ \Omega$.
(b) Volume constant, so $R\propto L^2$: $R'=17.5\times\left(\dfrac{3.0}{2.0}\right)^2=39.4\ \Omega$. (Using $R\propto L$ would give $26.3\ \Omega$ — it forgets that the wire also gets thinner.)
(c) $R\propto1/r^4$: $\dfrac{R'}{R}=\dfrac1{0.90^4}=1.524$, an increase of about $52\%$.
(d) $R=\rho\ell/A$. Largest: current along the $4.0\ \text{cm}$ edge through the $1.0\times2.0$ face, $R\propto\dfrac{4.0}{2.0}=2.0$. Smallest: along the $1.0\ \text{cm}$ edge through the $2.0\times4.0$ face, $R\propto\dfrac{1.0}{8.0}=0.125$. Ratio $=16$.
⏱ Shortcut For a block with edges $a\lt b\lt c$, $\dfrac{R_{\max}}{R_{\min}}=\dfrac{c/(ab)}{a/(bc)}=\dfrac{c^2}{a^2}=16$ here.

A uniform wire of resistance $R$ is stretched until its length is three times the original. Its new resistance is

Temperature dependence; electrical energy and power

When a metal is heated, the number of free electrons hardly changes, but the ions vibrate with larger amplitude and the electrons collide with them more often. The relaxation time $\tau$ falls, so $\rho=m/(ne^2\tau)$ rises. Over a moderate range of temperature the rise is very nearly linear.

📘 Definition 12.8 — Temperature coefficient of resistivity

If $\rho_0$ is the resistivity at a reference temperature $T_0$ (usually $0^\circ\text{C}$ or $20^\circ\text{C}$), the temperature coefficient of resistivity $\alpha$ is the fractional change in resistivity per kelvin:

$$\alpha=\frac{\rho_T-\rho_0}{\rho_0\,(T-T_0)}\qquad(\text{unit } \text{K}^{-1}\text{ or }{}^\circ\text{C}^{-1}).$$
📐 Result 12.4 — Resistance and temperature

Over a limited range of temperature (and neglecting the tiny change in the dimensions of the conductor),

$$\rho_T=\rho_0\left[1+\alpha(T-T_0)\right],\qquad R_T=R_0\left[1+\alpha(T-T_0)\right].$$
  • Metals: $\alpha\gt0$, of order $4\times10^{-3}\ \text{K}^{-1}$ (copper $3.9\times10^{-3}$, platinum $3.9\times10^{-3}$, tungsten $4.5\times10^{-3}$).
  • Alloys such as nichrome, manganin and constantan: high $\rho$ and very small $\alpha$ (about $10^{-5}$–$10^{-4}\ \text{K}^{-1}$) — used for standard resistors and heating elements.
  • Semiconductors and insulators: $\alpha\lt0$. Heating frees many more charge carriers; the increase in $n$ outweighs the fall in $\tau$, so $\rho$ falls steeply with temperature.

$\alpha$ is defined with respect to the reference temperature: for two temperatures $t_1$, $t_2$ use $\dfrac{R_2}{R_1}=\dfrac{1+\alpha(t_2-t_0)}{1+\alpha(t_1-t_0)}$. Only when $\alpha\,\Delta t\ll1$ may you use $R_2\approx R_1[1+\alpha(t_2-t_1)]$.

The steady rise of a metal's resistance makes it a thermometer: a platinum coil whose resistance is measured gives temperatures accurate to a fraction of a degree over hundreds of degrees. It also explains the lamp's curved V–I graph: a tungsten filament at $2500^\circ\text{C}$ has more than ten times its cold resistance, so the current surge at switch-on is large. Some metals and compounds lose all resistance below a critical temperature — superconductors — but that lies outside the linear law.

Energy and power. When a charge $\Delta q$ moves through a conductor from the end at potential $V_A$ to the end at the lower potential $V_B$, its electric potential energy falls by $\Delta q\,(V_A-V_B)=\Delta q\,V$. In a steady current the electrons do not gain kinetic energy on average (their drift speed stays the same), so this energy is handed to the ions in collisions and appears as heat — the Joule heating of the conductor. In a time $\Delta t$ the charge is $\Delta q=I\Delta t$, so the energy converted is $W=VI\Delta t$.

📐 Law 12.5 — Electrical energy and power (Joule's law of heating)

A device carrying a steady current $I$ with a potential difference $V$ across it converts electrical energy at the rate

$$P=VI ,\qquad W=VIt .$$

For a resistor, using $V=IR$: $\ P=I^2R=\dfrac{V^2}{R}$, and the heat produced in time $t$ is $H=I^2Rt$. The unit of power is the watt ($1\ \text{W}=1\ \text{J/s}=1\ \text{V A}$); electrical energy is sold in kilowatt hours, $1\ \text{kWh}=3.6\times10^6\ \text{J}$ (one "unit").

Which form to use depends on what is the same. Resistors in a series chain carry the same current, so $P=I^2R\propto R$ — the larger resistance dissipates more. Appliances connected to the mains share the same voltage, so $P=V^2/R\propto1/R$ — the smaller resistance dissipates more. An appliance labelled "$P_0$, $V_0$" has resistance $R=V_0^2/P_0$; on any other voltage $V$ (with $R$ unchanged) it gives $P=P_0\,(V/V_0)^2$.

The same idea is why electric power is transmitted at very high voltage. A power station sending power $P$ along lines of resistance $R_\text{c}$ at voltage $V$ needs a current $I=P/V$, and wastes $I^2R_\text{c}=P^2R_\text{c}/V^2$ in the lines: raising $V$ tenfold cuts the loss a hundredfold.

✏️ Example 5 — Resistance thermometers and the reference temperature
(a) A platinum resistance thermometer reads $4.00\ \Omega$ in melting ice and $5.56\ \Omega$ in steam at $100^\circ\text{C}$. Find $\alpha$, and the temperature of a furnace in which it reads $9.46\ \Omega$. (b) A copper coil has resistance $20.0\ \Omega$ at $20^\circ\text{C}$; for copper $\alpha=4.0\times10^{-3}\ {}^\circ\text{C}^{-1}$ referred to $0^\circ\text{C}$. Find its resistance at $70^\circ\text{C}$ exactly, and compare it with the quick estimate $R_{20}[1+\alpha(70-20)]$.
(a) $\alpha=\dfrac{R_{100}-R_0}{R_0\times100}=\dfrac{1.56}{400}=3.9\times10^{-3}\ {}^\circ\text{C}^{-1}$. Furnace: $t=\dfrac{R-R_0}{\alpha R_0}=\dfrac{5.46}{0.0156}=350^\circ\text{C}$.
(b) First find $R_0$: $R_0=\dfrac{20.0}{1+4.0\times10^{-3}\times20}=\dfrac{20.0}{1.08}=18.52\ \Omega$. Then $R_{70}=18.52\times(1+0.28)=23.7\ \Omega$.
Estimate $20.0\times(1+4.0\times10^{-3}\times50)=24.0\ \Omega$ — about $1.3\%$ too high, because $\alpha$ belongs to $0^\circ\text{C}$, not $20^\circ\text{C}$. In JEE Main use the exact ratio $\dfrac{R_2}{R_1}=\dfrac{1+\alpha t_2}{1+\alpha t_1}$ when the options are close.
Check In (a) the furnace reading is a little more than twice the ice reading, and $R_T/R_0=1+\alpha t$ gives $1+0.0039\times350=2.37=9.46/4.00$ ✓.
✏️ Example 6 — Two lamps on the mains
Two filament lamps are rated $100\ \text{W}$, $220\ \text{V}$ and $60\ \text{W}$, $220\ \text{V}$. Treat their resistances as constant. (a) Find the resistance of each. (b) They are connected in series across a $220\ \text{V}$ supply. Find the current and the power of each lamp. Which glows brighter? (c) What powers do they take when connected separately (in parallel) across the supply? (d) The $100\ \text{W}$ lamp is used for $5$ hours a day for $30$ days. Find the energy used and its cost at $\text{₹}\,8$ per kWh.
Find the power of the $60\ \text{W}$ lamp in the series connection (b) first:
(a) $R=\dfrac{V^2}{P}$: $\ R_{100}=\dfrac{220^2}{100}=484\ \Omega$, $\ R_{60}=\dfrac{220^2}{60}=807\ \Omega$.
(b) $I=\dfrac{220}{484+807}=0.170\ \text{A}$. $\ P_{100}=I^2R_{100}=14.1\ \text{W}$, $\ P_{60}=I^2R_{60}=23.4\ \text{W}$. The 60 W lamp glows brighter: in series the current is common, and $P=I^2R$ favours the larger resistance.
(c) In parallel each has the full $220\ \text{V}$, so they give their rated $100\ \text{W}$ and $60\ \text{W}$; now the $100\ \text{W}$ lamp is brighter.
(d) $W=0.100\ \text{kW}\times5\ \text{h}\times30=15\ \text{kWh}$; cost $=15\times\text{₹}\,8=\text{₹}\,120$.
⏱ Shortcut Lamps of equal rated voltage in series take a total power $\dfrac{P_1P_2}{P_1+P_2}=\dfrac{100\times60}{160}=37.5\ \text{W}$ $(=14.1+23.4\ ✓)$, and $P_1:P_2=R_1:R_2=\dfrac{1}{100}:\dfrac1{60}$.

In Interactive 2 choose the metal resistor at $20^\circ\text{C}$ and set $V=6.0\ \text{V}$: the current is $0.600\ \text{A}$. Keeping $V=6.0\ \text{V}$, heat the resistor to $120^\circ\text{C}$ ($\alpha=3.9\times10^{-3}\ {}^\circ\text{C}^{-1}$). What current flows now?

At $120^\circ\text{C}$ the readouts show $V/I=13.9\ \Omega$ $\left(=10.0\times(1+0.0039\times100)\right)$, $I=0.432\ \text{A}$ and $P=2.59\ \text{W}$, down from $3.60\ \text{W}$ at $20^\circ\text{C}$. The graph is still a straight line through the origin — the resistor is still ohmic at each fixed temperature — but the line is less steep, because a hotter metal has a larger resistance. ($0.83\ \text{A}$ is what a semiconductor-like fall in resistance would give.) Now try the lamp: its V/I is only $6.89\ \Omega$ at $1.5\ \text{V}$ but $12.0\ \Omega$ at $6.0\ \text{V}$, because the filament heats up as the current grows.
Interactive 2 — V–I Characteristics: Ohmic or Not?

Choose a device and set the voltage across it; the dot shows the working point on its I–V graph and the readouts give the static resistance $V/I$ and the power. Press Play to sweep the voltage and trace the whole characteristic. For the metal resistor, change its temperature: the dashed line is the same resistor at $20^\circ\text{C}$.

6.0 V20 °C
voltage $V$—
current $I$—
$V/I$—
power $VI$—
⚠️ JEE Main traps

1. Three different speeds. Drift speed ($\sim10^{-4}\ \text{m/s}$, from $I=neAv_d$), the random speed of the free electrons ($\sim10^5$–$10^6\ \text{m/s}$) and the speed at which the current is set up ($\sim10^8\ \text{m/s}$) are different things. "Why does the lamp light at once?" is about the last one.

2. What is held fixed? Same current through a non-uniform wire: $v_d\propto1/A$. Same voltage across a single uniform wire: $v_d=\mu V/L$, independent of $A$. Read the question for the fixed quantity before using a proportionality.

3. Stretching keeps the volume. $R\propto L^2\propto1/r^4$, not $R\propto L$. A wire drawn to $n$ times its length has $n^2$ times the resistance; and $\rho$ does not change at all.

4. The reference temperature of $\alpha$. $R_T=R_0(1+\alpha\Delta T)$ uses the resistance at the temperature $\alpha$ refers to. Between two other temperatures take the ratio $\dfrac{1+\alpha t_2}{1+\alpha t_1}$. And remember that semiconductors have $\alpha\lt0$.

5. Which power formula? In series (same $I$) use $I^2R$: the lamp of lower rated power has the larger resistance and glows brighter. In parallel (same $V$) use $V^2/R$. Rated values give $R=V_0^2/P_0$; the actual power on another voltage is $P_0(V/V_0)^2$.

A $25\ \text{W}$, $220\ \text{V}$ lamp and a $100\ \text{W}$, $220\ \text{V}$ lamp are connected in series across a $220\ \text{V}$ supply. Treating the resistances as constant,

Exercises

Take $e=1.6\times10^{-19}\ \text{C}$, $m_e=9.1\times10^{-31}\ \text{kg}$, $8.5\times10^{28}$ free electrons per $\text{m}^3$ and $\rho=1.7\times10^{-8}\ \Omega\,\text{m}$ for copper, and the specific heat capacity of water $4200\ \text{J kg}^{-1}\text{K}^{-1}$, unless told otherwise.

I
Current, drift velocity and mobility.
  • 1 A charge of $120\ \text{C}$ passes through a lamp in $1.0$ minute. Find the current.
  • 2 How many electrons per second pass a point in a wire carrying a current of $1.6\ \text{mA}$?
  • 3 The charge passing a cross-section is $q=(5t^2-2t+1)\ \text{C}$. Find the current at $t=3.0\ \text{s}$.
  • 4 A current falls uniformly from $10\ \text{A}$ to zero in $4.0\ \text{s}$. Find the charge that flows.
  • 5 A thin plastic ring of radius $5.0\ \text{cm}$ carries a charge of $2.0\ \mu\text{C}$ spread round it and spins about its axis at $30$ revolutions per second. Find the equivalent current, in $\mu\text{A}$. Does the radius matter?
  • 6 A copper wire of cross-section $2.0\ \text{mm}^2$ carries $4.0\ \text{A}$. Find the drift speed of its free electrons, in mm/s.
  • 7 Electrons in a conductor have mobility $5.0\times10^{-3}\ \text{m}^2\,\text{V}^{-1}\text{s}^{-1}$. Find their drift speed in a field of $0.020\ \text{V/m}$, and their relaxation time.
  • 8 Drift speeds are less than a millimetre per second. Explain why a lamp several metres from its switch lights as soon as the switch is closed.
1 $I=\dfrac{120}{60}=2.0\ \text{A}$.
2 $N=\dfrac{I}{e}=\dfrac{1.6\times10^{-3}}{1.6\times10^{-19}}=1.0\times10^{16}$ per second.
3 $I=\dfrac{dq}{dt}=10t-2=28\ \text{A}$ at $t=3.0\ \text{s}$.
4 $q=\tfrac12\times10\times4.0=20\ \text{C}$.
5 $I=qf=2.0\times10^{-6}\times30=6.0\times10^{-5}\ \text{A}=60\ \mu\text{A}$. The radius does not matter: all the charge passes any point once per revolution.
6 $v_d=\dfrac{I}{neA}=\dfrac{4.0}{8.5\times10^{28}\times1.6\times10^{-19}\times2.0\times10^{-6}}=1.47\times10^{-4}\ \text{m/s}=0.147\ \text{mm/s}$.
7 $v_d=\mu E=5.0\times10^{-3}\times0.020=1.0\times10^{-4}\ \text{m/s}$; $\ \tau=\dfrac{m\mu}{e}=\dfrac{9.1\times10^{-31}\times5.0\times10^{-3}}{1.6\times10^{-19}}=2.84\times10^{-14}\ \text{s}$.
8 The wire is full of free electrons. Closing the switch sets up the electric field all along the circuit almost at the speed of light, and every free electron — including those already inside the filament — starts drifting at once. No electron has to travel from the switch to the lamp.
II
Ohm's law, resistivity and V–I characteristics.
  • 1 A $9.0\ \text{V}$ battery drives $0.30\ \text{A}$ through a resistor. Find its resistance and conductance.
  • 2 Find the resistance of $50\ \text{m}$ of copper wire of diameter $1.0\ \text{mm}$.
  • 3 What length of nichrome wire ($\rho=1.1\times10^{-6}\ \Omega\,\text{m}$) of cross-section $0.20\ \text{mm}^2$ is needed to make a $22\ \Omega$ resistor?
  • 4 A wire of resistance $8.0\ \Omega$ is stretched uniformly to twice its length. Find its new resistance.
  • 5 Two wires of the same material have the same mass; the second is twice as long as the first. Find the ratio $R_1/R_2$ of their resistances.
  • 6 A wire is stretched so that its length increases by $0.50\%$. By what percentage does its resistance change?
  • 7 The I–V graphs (current on the vertical axis) of two wires are straight lines through the origin making angles of $30^\circ$ and $60^\circ$ with the voltage axis. Find the ratio of the resistance of the first wire to that of the second.
  • 8 A filament lamp takes $0.20\ \text{A}$ at $2.0\ \text{V}$ and $0.50\ \text{A}$ at $12\ \text{V}$. Find its resistance in each case. Is it ohmic? Explain.
1 $R=\dfrac{9.0}{0.30}=30\ \Omega$; $\ G=\dfrac1{30}=0.033\ \text{S}$.
2 $A=\pi(0.50\times10^{-3})^2=7.85\times10^{-7}\ \text{m}^2$; $\ R=\dfrac{1.7\times10^{-8}\times50}{7.85\times10^{-7}}=1.08\ \Omega$.
3 $L=\dfrac{RA}{\rho}=\dfrac{22\times2.0\times10^{-7}}{1.1\times10^{-6}}=4.0\ \text{m}$.
4 $R\propto L^2$: $8.0\times4=32\ \Omega$.
5 Equal volumes, so $R=\rho L^2/V_0\propto L^2$: $\dfrac{R_1}{R_2}=\left(\dfrac12\right)^2=0.25$.
6 $\dfrac{\Delta R}{R}\approx2\dfrac{\Delta L}{L}=1.0\%$ increase.
7 Slope $=I/V=1/R=\tan\theta$, so $\dfrac{R_1}{R_2}=\dfrac{\tan60^\circ}{\tan30^\circ}=\dfrac{\sqrt3}{1/\sqrt3}=3$. The line at $30^\circ$ (less steep) is the larger resistance.
8 $\dfrac{2.0}{0.20}=10\ \Omega$ and $\dfrac{12}{0.50}=24\ \Omega$. Not ohmic: $V/I$ changes, because the larger current heats the filament and a metal's resistance rises with temperature.
III
Temperature dependence, energy and power.
  • 1 A copper wire has resistance $2.00\ \Omega$ at $0^\circ\text{C}$; $\alpha=4.3\times10^{-3}\ {}^\circ\text{C}^{-1}$. Find its resistance at $50^\circ\text{C}$.
  • 2 A coil has resistance $10.0\ \Omega$ at $20^\circ\text{C}$ and $12.0\ \Omega$ at $70^\circ\text{C}$. Find its temperature coefficient of resistance referred to $20^\circ\text{C}$.
  • 3 A heater is rated $1000\ \text{W}$ at $230\ \text{V}$. Find its working resistance and the current it draws.
  • 4 A $1.5\ \text{kW}$ water heater runs for $2$ hours a day. Find the cost of running it for $30$ days at $\text{₹}\,7$ per kWh.
  • 5 A $60\ \text{W}$, $220\ \text{V}$ lamp is run on $110\ \text{V}$. Find its power, treating the resistance as constant.
  • 6 A $2.0\ \text{kW}$ kettle heats $1.5\ \text{kg}$ of water from $25^\circ\text{C}$ to $100^\circ\text{C}$. Find the time taken if no heat is lost, in seconds.
  • 7 The supply voltage to a heater falls by $10\%$. By what percentage does its power fall (resistance constant)?
  • 8 Explain why the resistance of a metal increases, and that of a semiconductor decreases, when they are heated.
1 $R=2.00\,(1+4.3\times10^{-3}\times50)=2.00\times1.215=2.43\ \Omega$.
2 $\alpha=\dfrac{12.0-10.0}{10.0\times50}=4.0\times10^{-3}\ {}^\circ\text{C}^{-1}$.
3 $R=\dfrac{V^2}{P}=\dfrac{230^2}{1000}=52.9\ \Omega$; $\ I=\dfrac{P}{V}=4.35\ \text{A}$.
4 $1.5\ \text{kW}\times2\ \text{h}\times30=90\ \text{kWh}$; cost $\text{₹}\,630$.
5 $P=60\times\left(\dfrac{110}{220}\right)^2=15\ \text{W}$.
6 $Q=mc\Delta T=1.5\times4200\times75=4.73\times10^5\ \text{J}$; $\ t=\dfrac{Q}{P}=\dfrac{4.725\times10^5}{2000}=236\ \text{s}$ (about $3.9$ minutes).
7 $P\propto V^2$: $\dfrac{P'}{P}=0.90^2=0.81$, a fall of $19\%$.
8 In a metal the number of free electrons is fixed; heating makes the ions vibrate more, collisions become more frequent, $\tau$ falls and $\rho=m/(ne^2\tau)$ rises. In a semiconductor heating releases many more charge carriers; the large rise in $n$ outweighs the fall in $\tau$, so $\rho$ falls.
IV
Harder problems and applications.
  • 1 A metal has conductivity $6.0\times10^7\ \text{S/m}$ and $8.0\times10^{28}$ free electrons per $\text{m}^3$. Find the electron mobility and the relaxation time.
  • 2 Wires A and B are of the same material. A is twice as long as B and has twice its diameter. Find $R_A/R_B$.
  • 3 A copper pipe $2.0\ \text{m}$ long has inner radius $1.0\ \text{cm}$ and outer radius $1.5\ \text{cm}$. Find its resistance from end to end.
  • 4 For copper, $\alpha=4.0\times10^{-3}\ {}^\circ\text{C}^{-1}$ referred to $0^\circ\text{C}$. At what temperature is the resistance of a copper wire twice its value at $20^\circ\text{C}$?
  • 5 In a wire of radius $1.0\ \text{mm}$ the current density falls off from the axis as $j=j_0(1-r/R)$, with $j_0=3.0\times10^6\ \text{A/m}^2$ and $R$ the radius of the wire. Find the current.
  • 6 A nichrome heating element is rated $1.0\ \text{kW}$ at $220\ \text{V}$ when it is at its working temperature of $820^\circ\text{C}$. For nichrome $\alpha=1.7\times10^{-4}\ {}^\circ\text{C}^{-1}$ referred to $20^\circ\text{C}$. Find its resistance at $20^\circ\text{C}$ and the current at the instant it is switched on.
  • 7 A $12\ \text{V}$ car battery is rated $60\ \text{A h}$. Find the energy it can deliver and how long it can run a $36\ \text{W}$ lamp.
  • 8 A power station delivers $100\ \text{kW}$ through lines of total resistance $0.50\ \Omega$. Find the power wasted in the lines if the power is sent at $1.0\ \text{kV}$, and if it is sent at $10\ \text{kV}$.
1 $\mu=\dfrac{\sigma}{ne}=\dfrac{6.0\times10^7}{8.0\times10^{28}\times1.6\times10^{-19}}=4.7\times10^{-3}\ \text{m}^2\,\text{V}^{-1}\text{s}^{-1}$; $\ \tau=\dfrac{m\mu}{e}=\dfrac{9.1\times10^{-31}\times4.69\times10^{-3}}{1.6\times10^{-19}}=2.67\times10^{-14}\ \text{s}$.
2 $R\propto\dfrac{L}{d^2}$: $\dfrac{R_A}{R_B}=\dfrac{2}{2^2}=0.5$.
3 $A=\pi(r_2^2-r_1^2)=\pi(2.25-1.00)\times10^{-4}=3.93\times10^{-4}\ \text{m}^2$; $\ R=\dfrac{1.7\times10^{-8}\times2.0}{3.93\times10^{-4}}=8.7\times10^{-5}\ \Omega$.
4 $\dfrac{1+\alpha t}{1+20\alpha}=2$: $1+\alpha t=2\times1.08=2.16$, so $t=\dfrac{1.16}{4.0\times10^{-3}}=290^\circ\text{C}$. (The careless $20+\dfrac1\alpha=270^\circ\text{C}$ is wrong.)
5 $I=\displaystyle\int_0^R j_0\left(1-\frac rR\right)2\pi r\,dr=2\pi j_0\left(\frac{R^2}{2}-\frac{R^2}{3}\right)=\frac{\pi j_0R^2}{3}=\frac{\pi\times3.0\times10^6\times10^{-6}}{3}=3.14\ \text{A}$.
6 Hot: $R=\dfrac{220^2}{1000}=48.4\ \Omega$. Cold: $R_{20}=\dfrac{48.4}{1+1.7\times10^{-4}\times800}=\dfrac{48.4}{1.136}=42.6\ \Omega$. Switch-on current $\dfrac{220}{42.6}=5.2\ \text{A}$, against $4.5\ \text{A}$ when hot.
7 $W=VQ=12\times60\times3600=2.6\times10^6\ \text{J}$; $\ t=\dfrac{12\times60\ \text{W h}}{36\ \text{W}}=20\ \text{h}$.
8 At $1.0\ \text{kV}$: $I=100\ \text{A}$, loss $I^2R=5.0\ \text{kW}$ ($5\%$). At $10\ \text{kV}$: $I=10\ \text{A}$, loss $50\ \text{W}$ — a hundred times less.
🎯 Exam corner JEE Main · MCQJEE Main · Numerical

E1. JEE Main · MCQ A potential difference $V$ across a copper wire of length $L$ and radius $r$ gives the free electrons a drift speed $v$. The same potential difference is applied across a copper wire of length $2L$ and radius $2r$ at the same temperature. The drift speed in the second wire is (A) $v$ (B) $2v$ (C) $v/2$ (D) $v/4$

Idea $v_d=\mu E=\dfrac{\mu V}{L}$; the mobility is the same (same metal, same temperature).
Compare $L$ doubles, so $E$ and $v_d$ halve. The radius does not enter.
Answer (C).
⏱ Shortcut (D) comes from using $v_d=I/(neA)$ with the current wrongly held fixed. Here the voltage is fixed.

E2. JEE Main · Numerical A uniform wire of resistance $4\ \Omega$ is drawn out, keeping its volume constant, until its radius is half the original radius. Find its new resistance in ohms. Give the answer to the nearest integer.

Volume $AL$ constant: halving $r$ divides $A$ by $4$ and multiplies $L$ by $4$.
Resistance $R=\rho L/A$ grows by $4\times4=16$: $R'=16\times4=64\ \Omega$.
Answer $64$.
⏱ Shortcut $R\propto1/r^4$: $2^4=16$.

E3. JEE Main · MCQ The resistance of a metal wire is $5.0\ \Omega$ at $50^\circ\text{C}$ and $6.0\ \Omega$ at $100^\circ\text{C}$. Assuming $R_t=R_0(1+\alpha t)$, its resistance at $0^\circ\text{C}$ is (A) $4.0\ \Omega$ (B) $4.5\ \Omega$ (C) $3.0\ \Omega$ (D) $4.2\ \Omega$

Ratio $\dfrac{6.0}{5.0}=\dfrac{1+100\alpha}{1+50\alpha}$, so $6+300\alpha=5+500\alpha$ and $\alpha=5.0\times10^{-3}\ {}^\circ\text{C}^{-1}$.
$R_0$ $R_0=\dfrac{5.0}{1+50\times0.005}=\dfrac{5.0}{1.25}=4.0\ \Omega$.
Answer (A).
⏱ Shortcut $R$ is linear in $t$: it rises $1.0\ \Omega$ per $50^\circ\text{C}$, so going back $50^\circ\text{C}$ from $5.0\ \Omega$ gives $4.0\ \Omega$.

E4. JEE Main · Numerical A $40\ \text{W}$, $220\ \text{V}$ lamp and a $60\ \text{W}$, $220\ \text{V}$ lamp are connected in series across a $220\ \text{V}$ supply. Treating their resistances as constant, find the total power drawn, in watts. Give the answer to the nearest integer.

Resistances $R_1=\dfrac{220^2}{40}=1210\ \Omega$, $\ R_2=\dfrac{220^2}{60}=806.7\ \Omega$.
Power $P=\dfrac{220^2}{R_1+R_2}=\dfrac{48\,400}{2016.7}=24.0\ \text{W}$.
Answer $24$.
⏱ Shortcut $\dfrac1P=\dfrac1{P_1}+\dfrac1{P_2}$ for equal rated voltages: $P=\dfrac{40\times60}{100}=24\ \text{W}$.

E5. JEE Main · MCQ A metal wire is connected across a battery of constant terminal voltage and its temperature is then raised. Which statement is correct? (A) The number density of free electrons rises, so the current rises (B) The relaxation time falls, so the drift speed and the current fall (C) The relaxation time rises, so the drift speed rises (D) The drift speed is unchanged because the field $V/L$ is unchanged

Idea In a metal $n$ is fixed; hotter ions vibrate more, so collisions are more frequent and $\tau$ falls.
Effect $v_d=eE\tau/m$ falls even though $E=V/L$ is unchanged, and $I=neAv_d$ falls: the resistance has risen.
Answer (B).
⏱ Shortcut (A) describes a semiconductor; (D) forgets that $v_d$ depends on $\tau$ as well as on $E$.

E6. JEE Main · Numerical A wire of cross-sectional area $1.0\ \text{mm}^2$ carries a current of $2.56\ \text{A}$. The metal has $8.0\times10^{28}$ free electrons per cubic metre. If the drift speed is $x\times10^{-5}\ \text{m/s}$, find $x$ to the nearest integer. ($e=1.6\times10^{-19}\ \text{C}$)

Formula $v_d=\dfrac{I}{neA}$.
Numbers $neA=8.0\times10^{28}\times1.6\times10^{-19}\times1.0\times10^{-6}=12.8\ \text{A s/m}$; $\ v_d=\dfrac{2.56}{12.8}=0.20\times10^{-3}\ \text{m/s}=20\times10^{-5}\ \text{m/s}$.
Answer $20$.
⏱ Shortcut Convert $\text{mm}^2$ to $\text{m}^2$ ($10^{-6}$) before dividing — forgetting it gives an answer a million times too small.
🔬 Research–Teaching NexusResearch-tutored · optional, about 45 minutes

Research question. How does the resistance of a filament lamp change as it heats up, and can its V–I curve be used to estimate the filament's temperature?

Why it matters. Temperature-dependent resistance is used every day around the world: platinum resistance thermometers control industrial furnaces and medical sterilisers, hot-wire sensors measure the air flowing into car engines and patients' lungs, and thermistors protect phone batteries from overheating. Engineers designing lighting, heaters and fuses must also know how much larger the current is at switch-on, when a filament or element is cold (Result 12.4). A cheap lamp, a cell and two meters let you measure all of this.

What to do.

  1. Connect a small filament lamp (for example $6\ \text{V}$, $0.3\ \text{A}$) in series with an ammeter and a variable supply or a potential divider, with a voltmeter across the lamp.
  2. Increase the voltage from zero in small steps up to the rated value, recording $V$ and $I$ each time; use very small steps at first, where the filament is still cold.
  3. Plot $I$ against $V$ and then $R=V/I$ against $V$. Read off the "cold" resistance $R_0$ by extrapolating to $V=0$.
  4. Using $R=R_0[1+\alpha(T-T_0)]$ with $\alpha=4.5\times10^{-3}\ \text{K}^{-1}$ for tungsten, estimate the filament temperature at each point.
  5. Repeat the measurements with an ordinary fixed resistor and compare the two graphs.

Tools: Filament lamp, fixed resistor, low-voltage supply or cells with a rheostat, ammeter, voltmeter (or two multimeters), connecting leads, graph paper or a spreadsheet.

Hand in: Your table of readings, the two graphs for each device, the estimated filament temperature at the rated voltage, and a paragraph explaining which device is ohmic and why the lamp is not.

Going further. The linear law underestimates tungsten's resistance at high temperatures. Try fitting $R\propto T^{1.2}$ instead and compare the two temperature estimates. Also measure the power $VI$ at each point: radiated power from a hot body grows very fast with temperature — does your data show it?

Instructor note: typical small lamps show $R$ rising by a factor of $8$–$12$ from cold to rated voltage, giving filament temperatures of about $2000$–$2700\ \text{K}$ with the linear law (an overestimate). Warn students to wait a few seconds after each step for the filament to settle, and to keep the voltage at or below the rated value. The fixed resistor gives a straight line through the origin — a clear contrast.

🧪 Self-check quiz

0/5 correct

Q1. The SI unit of electron mobility is

Q2. The resistivity of a metal wire depends on

Q3. A wire with $n$ free electrons per unit volume and cross-section $A$ carries a current $I$. The drift speed of the electrons is

Q4. The I–V graphs of the same metal wire at temperatures $T_1$ and $T_2$ are straight lines through the origin, with current on the vertical axis; the line for $T_1$ is steeper. Then

Q5. The heating coil of a heater is replaced by one of half the resistance, and the heater is used on the same mains supply. Its power