Chapter 12 · Current Electricity

12.3 The Wheatstone Bridge and the Metre Bridge

Four resistors in a diamond, a cell across one diagonal and a galvanometer across the other: when the galvanometer reads zero, $P/Q=R/S$ — whatever the cell, whatever the galvanometer. The same balance lets you erase a resistor from a network, and, stretched along a metre of uniform wire, it becomes the metre bridge: $X=R\,(100-l)/l$.

How would you measure a resistance accurately? The obvious way is to pass a current through it, read the current on an ammeter and the potential difference on a voltmeter, and divide. But every meter disturbs what it measures: the voltmeter draws a little current of its own, the ammeter has a little resistance of its own, and the readings are only as good as the calibration of the scales. To do better you want a method in which the meter does not have to give a reading at all — only tell you when a current is exactly zero.

That is the idea of a null method, and the Wheatstone bridge (named after Charles Wheatstone, who made it famous in 1843) is the classic example. An unknown resistance is compared with known ones until a sensitive galvanometer shows no deflection; at that moment a simple ratio of resistances gives the answer, independent of the cell's emf and of the galvanometer's resistance. In this section we derive the balance condition from Kirchhoff's laws, find out when the bridge is most sensitive, use the balanced bridge and symmetry as shortcuts for the equivalent resistance of networks, and build the laboratory version — the metre bridge — including the end errors that every careful experimenter must deal with. You will need Kirchhoff's junction and loop laws from Section 12.2 and the idea of resistivity from Section 12.1.

The Wheatstone bridge and its balance condition

Take four resistors and join them in a closed loop $ABCDA$: $P$ between $A$ and $B$, $Q$ between $B$ and $C$, $S$ between $C$ and $D$, and $R$ between $D$ and $A$. Connect a cell between the opposite corners $A$ and $C$, and a galvanometer (a sensitive current detector, centre-zero, whose needle swings left or right according to the direction of the current) between the other two corners $B$ and $D$. Draw it as a diamond with $A$ on the left, $C$ on the right, $B$ at the top and $D$ at the bottom — that is the picture in Interactive 1 below.

📘 Definition 12.12 — The Wheatstone bridge

A Wheatstone bridge is a network of four resistors $P$, $Q$, $S$, $R$ joined in a loop $ABCDA$, with a cell (the battery arm) connected across one diagonal $AC$ and a galvanometer (the galvanometer arm) across the other diagonal $BD$. The two resistors meeting at $B$, $P$ and $Q$, are called the ratio arms; usually $R$ is a known adjustable resistance and $S$ is the resistance to be measured.

The current from the cell divides at $A$: part flows along the upper path $A\to B\to C$, part along the lower path $A\to D\to C$, and the galvanometer "bridges" the two paths.

The potential falls steadily along each path from $A$ (the high-potential end, joined to the positive terminal) to $C$. Somewhere along the upper path the potential at $B$ has some value $V_B$; somewhere along the lower path $D$ has a value $V_D$. If $V_B\ne V_D$ a current flows through the galvanometer from the higher to the lower. If $V_B=V_D$ exactly, no current flows through it — whatever its resistance.

📘 Definition 12.13 — Balanced bridge and null point

A Wheatstone bridge is balanced when the current through the galvanometer arm is zero, $I_g=0$, so that $B$ and $D$ are at the same potential. The galvanometer then shows null deflection; the setting at which this happens is the null point (or balance point).

Derivation from Kirchhoff's laws. Let a current $I_1$ enter $P$ at $A$ and a current $I_2$ enter $R$ at $A$, and let $I_g$ flow through the galvanometer (resistance $G$) from $B$ to $D$. By the junction law, $Q$ carries $I_1-I_g$ (from $B$ to $C$) and $S$ carries $I_2+I_g$ (from $D$ to $C$). Now apply the loop law to the two small loops that contain the galvanometer:

$$\text{loop }ABDA:\quad I_1P+I_gG-I_2R=0$$ $$\text{loop }BCDB:\quad (I_1-I_g)Q-(I_2+I_g)S-I_gG=0$$

At balance $I_g=0$, and these become $I_1P=I_2R$ and $I_1Q=I_2S$. Dividing the first by the second,

$$\frac{P}{Q}=\frac{R}{S}.$$

Notice what did not enter: the emf of the cell, its internal resistance and the galvanometer's resistance $G$ all dropped out. The same result follows in one line from potentials: with $I_g=0$ the same current $I_1$ flows through $P$ and $Q$, so $V_A-V_B=I_1P$ and $V_B-V_C=I_1Q$; likewise $V_A-V_D=I_2R$, $V_D-V_C=I_2S$. Setting $V_B=V_D$ makes the two drops on the left equal and the two on the right equal, and dividing gives the same ratio.

Conversely, solving the loop equations together with the battery loop (Kirchhoff's laws give three equations for $I_1$, $I_2$, $I_g$) for an ideal cell of emf $\varepsilon$ gives the galvanometer current in any bridge:

$$I_g=\frac{\varepsilon\,(QR-PS)}{\Delta}\quad(\text{from }B\text{ to }D),$$ $$\Delta=G(P+Q)(R+S)$$ $$\qquad+PQ(R+S)+RS(P+Q).$$

The denominator $\Delta$ is always positive, so $I_g=0$ if and only if $PS=QR$; and the sign of $QR-PS$ tells you which way the needle swings.

📐 Law 12.13 — Balance condition of the Wheatstone bridge

In a Wheatstone bridge with $P$, $Q$ meeting at $B$ and $R$, $S$ meeting at $D$ (with $P$ and $R$ joined at $A$), the galvanometer current is zero if and only if

$$\frac{P}{Q}=\frac{R}{S}\qquad(\text{equivalently } PS=QR).$$

The condition does not depend on the emf or internal resistance of the cell, on the resistance of the galvanometer, or on which diagonal holds the cell and which the galvanometer: interchanging the cell and the galvanometer leaves a balanced bridge balanced (the condition $PS=QR$ is unchanged). In a balanced bridge the galvanometer arm carries no current, so it may be removed — or replaced by a plain wire — without changing any other current.

The last sentence is the key to the network shortcuts later: a balanced bridge between $A$ and $C$ is simply two parallel paths, $P+Q$ and $R+S$, and its equivalent resistance is

$$R_{\text{eq}}=\frac{(P+Q)(R+S)}{P+Q+R+S}.$$

(Replacing the middle arm by a wire instead gives $(P\parallel R)+(Q\parallel S)$, which is the same number when $PS=QR$ — a useful check.) A good way to remember which pairs go in the ratio: walk round the diamond starting from the cell's corner $A$. The two resistors you meet first, $P$ and $R$, go on top; the two that end at $C$, $Q$ and $S$, go underneath. The ratio is always "first arm on one side ÷ second arm on that side", never across the diagonal.

✏️ Example 1 — Balancing a bridge
In a Wheatstone bridge $P=10\ \Omega$, $Q=30\ \Omega$ and $R=15\ \Omega$; an ideal $6.0\ \text{V}$ cell is connected across $AC$. (a) Find the value of $S$ for which the galvanometer shows no deflection. (b) At balance, find the current in each arm, the current drawn from the cell and the potential of $B$ and of $D$ (take $V_C=0$). (c) The cell and the galvanometer are now interchanged. Does the galvanometer deflect?
(a) $\dfrac{P}{Q}=\dfrac{R}{S}$: $S=\dfrac{QR}{P}=\dfrac{30\times15}{10}=45\ \Omega$.
(b) No current in the galvanometer, so the paths are independent: upper path $P+Q=40\ \Omega$ carries $\dfrac{6.0}{40}=0.15\ \text{A}$; lower path $R+S=60\ \Omega$ carries $\dfrac{6.0}{60}=0.10\ \text{A}$. Cell current $0.25\ \text{A}$ (equivalent resistance $\dfrac{40\times60}{100}=24\ \Omega$ ✓).
Potentials $V_B=0.15\times30=4.5\ \text{V}$, $V_D=0.10\times45=4.5\ \text{V}$ — equal, as balance requires.
(c) No. The balance condition $PS=QR$ ($10\times45=30\times15=450$) does not mention which diagonal holds the cell, so the bridge stays balanced.
✏️ Example 2 — An unbalanced bridge by Kirchhoff's laws
In a bridge $P=10\ \Omega$, $Q=20\ \Omega$, $R=20\ \Omega$, $S=10\ \Omega$; the galvanometer has resistance $G=20\ \Omega$ and an ideal $12\ \text{V}$ cell is connected across $AC$ ($A$ positive). (a) Find the current through the galvanometer and its direction. (b) Find the current drawn from the cell and the equivalent resistance of the network between $A$ and $C$.
Find the galvanometer current before you open the solution:
Check $PS=100$, $QR=400$: not balanced, and since $QR\gt PS$ the current flows from $B$ to $D$.
Symmetry Rotating the diamond through half a turn swaps $A\leftrightarrow C$ and $B\leftrightarrow D$ and maps every resistor onto an equal one ($P\leftrightarrow S$, $Q\leftrightarrow R$). So the potentials are mirrored about $6\ \text{V}$: $V_D=12-V_B$.
Junction at $B$ Currents leaving $B$ add to zero: $\dfrac{V_B-12}{10}+\dfrac{V_B}{20}+\dfrac{V_B-(12-V_B)}{20}=0$. Multiply by $20$: $2V_B-24+V_B+2V_B-12=0$, so $V_B=7.2\ \text{V}$ and $V_D=4.8\ \text{V}$.
(a) $I_g=\dfrac{V_B-V_D}{G}=\dfrac{2.4}{20}=0.12\ \text{A}$ from $B$ to $D$. The formula agrees: $\Delta=20\times30\times30+200\times30+200\times30=30\,000$, and $I_g=\dfrac{12\times300}{30\,000}=0.12\ \text{A}$ ✓.
(b) From $A$: through $P$, $\dfrac{12-7.2}{10}=0.48\ \text{A}$; through $R$, $\dfrac{12-4.8}{20}=0.36\ \text{A}$. Cell current $0.84\ \text{A}$, so $R_{\text{eq}}=\dfrac{12}{0.84}=14.3\ \Omega$.
Check At $B$: in $0.48\ \text{A}$; out through $Q$, $\dfrac{7.2}{20}=0.36\ \text{A}$, and through $G$, $0.12\ \text{A}$ ✓. Removing the galvanometer would give $\dfrac{30\times30}{60}=15\ \Omega$; the bridging arm adds a third path, so $R_{\text{eq}}$ is a little smaller.
⏱ Shortcut For any unbalanced bridge, the node-potential method needs only two unknowns ($V_B$, $V_D$) — faster and safer than three loop currents.

In Interactive 1 set $P=10\ \Omega$, $Q=20\ \Omega$, $R=30\ \Omega$ (the cell is $6.0\ \text{V}$). For which value of $S$ does the needle read zero, and what happens to that null value if you then change $G$ from $50\ \Omega$ to $200\ \Omega$?

Slide $S$ (or press Play and watch the sweep): the needle passes through zero at $S=QR/P=20\times30/10=60\ \Omega$, where the readouts show $I_g=0$, $V_B=V_D=4.00\ \text{V}$, $P/Q=R/S=0.500$ and a cell current of $0.267\ \text{A}$ ($6/30+6/90$). Change $G$: the curve of $I_g$ against $S$ gets steeper or flatter, but it still crosses zero at $60\ \Omega$ — the balance condition does not contain $G$. ($15\ \Omega$ comes from $PR/Q$, pairing the arms across the diagonal.)
Interactive 1 — Wheatstone Bridge: Hunting the Null

A $6.0\ \text{V}$ ideal cell drives the bridge $ABCD$. Set the four arms and the galvanometer resistance $G$; the needle and the readouts follow Kirchhoff's laws exactly. The graph shows the galvanometer current against $S$ for your $P$, $Q$, $R$, $G$ — it crosses zero at $S=QR/P$. Press Play to sweep $S$ and watch the needle swing through the null.

10 Ω20 Ω30 Ω40 Ω50 Ω
galvanometer $I_g$—
$V_B$ and $V_D$—
$P/Q$ and $R/S$—
cell current—

In a Wheatstone bridge $P=2\ \Omega$ and $Q=4\ \Omega$ meet at $B$, and $R=3\ \Omega$ and $S$ meet at $D$ ($P$ and $R$ are joined at $A$). The bridge is balanced when $S$ equals

Sensitivity of the bridge

At balance the galvanometer reads zero; the question is how sharply it tells you that you are off balance. If $S$ differs from the balance value by a small fraction, a good bridge gives a clearly visible deflection; a poor one barely twitches, and you cannot locate the null precisely. This property is the sensitivity of the bridge.

Write $S=S_0+\Delta S$, where $S_0=QR/P$ is the balance value. Then $QR-PS=-P\,\Delta S$, and the general formula gives, for small $\Delta S$,

$$I_g\approx-\frac{\varepsilon\,P\,\Delta S}{\Delta_0},$$

where $\Delta_0$ is the denominator $\Delta$ evaluated at $S=S_0$.

The current is proportional to $\Delta S$ — that is what makes the null sharp — and the slope depends on the arms. The cleanest case is the one most bridges are designed for, with all four arms equal.

📐 Result 12.14 — Sensitivity of a bridge near balance

If $P=Q=R=R_0$ and $S=R_0(1+\delta)$ with $|\delta|\ll1$, and the cell is ideal with emf $\varepsilon$, the galvanometer current is

$$|I_g|\approx\frac{\varepsilon\,\delta}{4\,(G+R_0)} .$$

In general the bridge is most sensitive when the four arms are of the same order of magnitude as one another (and the galvanometer resistance is comparable with them), and when the emf is as large as heating of the resistors allows. Very unequal ratio arms (say $10\ \Omega$ and $1000\ \Omega$) make the bridge much less sensitive, even though it can still balance.

Proof of the formula. With all arms $R_0$ the denominator is $G\cdot2R_0\cdot2R_0$ $+\,R_0^2\cdot2R_0$ $+\,R_0^2\cdot2R_0$ $=4R_0^2(G+R_0)$, and $P\,\Delta S=R_0\cdot R_0\delta$; dividing gives $\varepsilon\delta/[4(G+R_0)]$. If the galvanometer can just detect a current $I_{\min}$, the smallest detectable fractional change is $\delta_{\min}=4(G+R_0)I_{\min}/\varepsilon$.

Using a bridge in practice. Three habits come from these ideas. (1) Close the cell key first and the galvanometer key second (and open them in the reverse order): at the moment of switching, currents take a short time to settle and can kick the galvanometer even when the bridge is balanced. (2) Protect the galvanometer with a high resistance or a shunt while you are far from balance, and remove it near the null to get full sensitivity. (3) Pass current only briefly: the resistors heat up and their resistances change, so the null drifts.

Bridges as sensors. The same proportionality $I_g\propto\delta$ is exploited on purpose. A strain gauge — a fine metal track glued to a beam — changes its resistance by a fraction of a per cent when the beam is stretched; placed as one arm of a bridge balanced at zero load, it gives an out-of-balance current proportional to the strain. Electronic weighing scales, load cells in cranes and the pressure sensors in medical monitors work this way. Resistance thermometers use a platinum coil as the fourth arm.

✏️ Example 3 — How sensitive is the bridge?
A strain gauge of resistance $100\ \Omega$ forms the arm $S$ of a bridge with $P=Q=R=100\ \Omega$, a galvanometer of resistance $50\ \Omega$ and an ideal $3.0\ \text{V}$ cell. When the beam is loaded, the gauge's resistance rises by $1.0\%$. (a) Find the galvanometer current, exactly and from Result 12.14. (b) The same gauge is instead balanced with $P=10\ \Omega$, $Q=1000\ \Omega$, $R=1.0\ \Omega$. Check that this bridge also balances at $100\ \Omega$ and find the galvanometer current for the same $1.0\%$ change. Which arrangement is better?
(a) Exact $S=101\ \Omega$: $QR-PS=10\,000-10\,100=-100\ \Omega^2$. $\Delta=50\times200\times201$ $+\,10^4\times201$ $+\,100\times101\times200$ $=6.04\times10^6\ \Omega^3$. $I_g=\dfrac{3.0\times(-100)}{6.04\times10^6}=-4.97\times10^{-5}\ \text{A}$, i.e. $49.7\ \mu\text{A}$ from $D$ to $B$.
(a) Estimate $\dfrac{\varepsilon\delta}{4(G+R_0)}=\dfrac{3.0\times0.010}{4\times150}=5.0\times10^{-5}\ \text{A}=50\ \mu\text{A}$ — within $1\%$ of the exact value.
(b) $QR/P=1000\times1.0/10=100\ \Omega$ ✓. With $S=101\ \Omega$: $QR-PS=1000-1010=-10$; $\Delta=50\times1010\times102$ $+\,10^4\times102$ $+\,1.0\times101\times1010$ $=6.27\times10^6$. $I_g=\dfrac{3.0\times10}{6.27\times10^6}=4.78\ \mu\text{A}$.
Verdict The equal-arm bridge gives about ten times the deflection for the same change: arms of the same order make the bridge sensitive.

You want to measure a resistance of about $1\ \text{k}\Omega$ as precisely as possible with a Wheatstone bridge. The best choice of ratio arms $P$, $Q$ and known arm $R$ is

Balanced bridges in networks — symmetry shortcuts

JEE Main loves networks that look complicated but contain a balanced bridge in disguise. The rule from Law 12.13 is: if a resistor joins two points that are at the same potential, it carries no current and can be removed (or replaced by a wire). A balanced bridge is the commonest source of such a pair of points, but symmetry gives many more.

📐 Result 12.15 — Equipotential points and symmetry

Let a current enter a network at $A$ and leave at $B$.

  • Two points at the same potential may be joined by a wire, or a resistor between them removed, without changing any current.
  • Mirror symmetry through the terminals. If the network is unchanged by reflection in a line (or plane) that passes through $A$ and $B$, then points that are mirror images of each other are at the same potential.
  • Symmetry that swaps the terminals. If the network is unchanged by a reflection or rotation that exchanges $A$ and $B$, then $V_{P'}=V_A+V_B-V_P$ for a point $P$ and its image $P'$; in particular every point that maps onto itself is at the mean potential $\tfrac12(V_A+V_B)$.
🧭 Problem-solving strategy — Equivalent resistance of a tricky network
  1. Mark the input $A$ and output $B$. Redraw the network if necessary so that each path from $A$ to $B$ is clear.
  2. Look for a bridge: two paths from $A$ to $B$ joined by a cross-resistor. Test $P/Q=R/S$ with the ratios taken along each path. If balanced, delete the cross-resistor.
  3. Look for symmetry: points that are mirror images in a line through $A$ and $B$ are equipotential — join them; points on a plane that swaps $A$ and $B$ sit at the mean potential.
  4. If neither works, use node potentials: set $V_A=V$, $V_B=0$, write the junction law at each remaining node, find the current $I$ leaving $A$, and $R_{\text{eq}}=V/I$.
  5. Check limits: $R_{\text{eq}}$ must be less than the resistance of any single path from $A$ to $B$.

The cube. Twelve equal resistors $r$ along the edges of a cube are a favourite test of symmetry. Between the ends of a body diagonal the three edges leaving $A$ are related by symmetry, so their far ends are at one potential, and likewise the three corners next to $B$. Join each set: the network becomes three groups in series — three resistors in parallel, six in parallel, three in parallel — so $R=\tfrac r3+\tfrac r6+\tfrac r3=\tfrac56r$. Between the ends of a face diagonal the result is $\tfrac34r$, and between the ends of an edge it is $\tfrac7{12}r$ (both follow from the node method with the symmetry rules; try them in Exercise III).

A square with a diagonal. Four equal resistors form a square $ABCD$ with a fifth across the diagonal $AC$. Between $B$ and $D$ the line $BD$ is a mirror line through the terminals, $A$ and $C$ are mirror images, so the diagonal carries nothing — it is a balanced bridge. Between $A$ and $C$, however, the diagonal is in parallel with the two sides-paths and certainly carries current.

✏️ Example 4 — A hidden bridge and a cube
(a) Between terminals $A$ and $B$ five resistors form a bridge: $2\ \Omega$ from $A$ to $C$, $4\ \Omega$ from $C$ to $B$, $3\ \Omega$ from $A$ to $D$, $6\ \Omega$ from $D$ to $B$, and $5\ \Omega$ between $C$ and $D$. A sixth resistor of $6\ \Omega$ joins $A$ directly to $B$. Find the equivalent resistance between $A$ and $B$. (b) Twelve resistors of $12\ \Omega$ each form the edges of a cube. Find the equivalent resistance between two opposite corners (ends of a body diagonal), and the current in each edge when a $20\ \text{V}$ ideal cell is connected across them.
Find the answer to (a) before you open the solution:
(a) Test Along the paths: $\dfrac{2}{4}=\dfrac{3}{6}=0.5$ — balanced, so $C$ and $D$ are at the same potential and the $5\ \Omega$ resistor carries no current.
(a) Combine Paths $2+4=6\ \Omega$ and $3+6=9\ \Omega$ in parallel: $\dfrac{6\times9}{15}=3.6\ \Omega$. In parallel with the direct $6\ \Omega$: $\dfrac{3.6\times6}{9.6}=2.25\ \Omega$.
(b) Symmetry The three corners next to $A$ are equivalent, and so are the three next to $B$. Current $I$ splits $I/3$ into each of the first three edges, $I/6$ into each of the six middle edges, and recombines as $I/3$ in each of the last three.
(b) Resistance Along any path $A\to B$: $V=\dfrac I3r+\dfrac I6r+\dfrac I3r=\dfrac56Ir$, so $R=\dfrac56\times12=10\ \Omega$.
(b) Currents $I=\dfrac{20}{10}=2.0\ \text{A}$: $0.67\ \text{A}$ in each of the six edges touching $A$ or $B$, $0.33\ \text{A}$ in each of the six middle edges.
⏱ Shortcut Before any arithmetic, compute the two ratios along the paths. Half of all "find $R_{AB}$" network problems in JEE Main collapse at that first step.

Resistors of $1\ \Omega$ ($A$ to $C$), $2\ \Omega$ ($C$ to $B$), $2\ \Omega$ ($A$ to $D$) and $4\ \Omega$ ($D$ to $B$) form a bridge with a $10\ \Omega$ resistor between $C$ and $D$. The equivalent resistance between $A$ and $B$ is

The metre bridge

In the laboratory the ratio arms $P$ and $Q$ are replaced by two parts of a single uniform wire. The metre bridge (also called the slide-wire bridge) is a wire exactly $1\ \text{m}$ long, of uniform cross-section, stretched along a metre scale on a wooden board. Its ends $A$ and $C$ are soldered to thick copper strips (of negligible resistance) that form an L-shape at each end and leave two gaps above the wire, separated by a central copper strip with a terminal $B$. A known resistance $R$ (a resistance box) goes in the left gap and the unknown $X$ in the right gap. A cell and key are connected between $A$ and $C$; a galvanometer is connected from $B$ to a jockey — a knife-edge contact that is pressed onto the wire at any point $D$.

📘 Definition 12.14 — Metre bridge and balancing length

A metre bridge is a Wheatstone bridge in which two arms are the lengths $AD$ and $DC$ of a uniform $100\ \text{cm}$ wire on either side of a sliding contact (the jockey) at $D$, and the other two arms are the resistances $R$ and $X$ placed in the gaps between thick copper strips. The balancing length $l$ is the distance $AD$, measured from the end $A$ on the side of the left gap, at which the galvanometer shows null deflection.

The wire is made of an alloy such as manganin or constantan: its resistivity is high (so a metre of it has a convenient resistance of a few ohms) and its temperature coefficient is very small (so it does not change as the current warms it). Being uniform, it has the same resistance $\lambda$ per centimetre all along, so $AD$ has resistance $\lambda l$ and $DC$ has $\lambda(100-l)$.

📐 Law 12.16 — The metre-bridge formula

With $R$ in the left gap, $X$ in the right gap and null point at a distance $l$ (in cm) from the left end,

$$\frac{R}{X}=\frac{\lambda l}{\lambda(100-l)}=\frac{l}{100-l},\qquad X=R\,\frac{100-l}{l}.$$

The result is independent of $\lambda$, of the cell and of the galvanometer. If a misreading of $l$ by $\Delta l$ is the main error, the fractional error in $X$ is

$$\frac{\Delta X}{X}=\frac{100\,\Delta l}{l\,(100-l)},$$

which is least when the null point is near the middle of the wire ($l\approx50\ \text{cm}$). So $R$ should be chosen close to $X$.

Where the error formula comes from. From $\ln X=\ln R+\ln(100-l)-\ln l$, a change $\Delta l$ changes $\ln X$ by $\Delta l\left(\dfrac1{100-l}+\dfrac1l\right)=\dfrac{100\,\Delta l}{l(100-l)}$. The product $l(100-l)$ is largest — and the error smallest — at $l=50$, where $\Delta X/X=0.04\,\Delta l$ (with $\Delta l$ in cm): a $1\ \text{mm}$ misreading costs only $0.4\%$. At $l=10\ \text{cm}$ the same slip costs $1.1\%$. A null point near the middle is also where the four arms are most alike — the sensitivity rule of Result 12.14 again.

End errors. The formula assumes that the wire starts exactly at the zero of the scale and that the copper strips have zero resistance. In a real bridge the joins at each end (solder, clamping screws, the copper strip itself) add a little resistance, and the zero of the scale may not coincide with the start of the wire. Each end behaves as if the wire had an extra length: $\alpha$ at the left end and $\beta$ at the right end. These are the end errors (or end corrections) of the bridge.

📐 Result 12.17 — Metre bridge with end errors; interchanging $R$ and $X$

With end errors $\alpha$ (left end) and $\beta$ (right end), expressed as equivalent lengths of the bridge wire, the balance condition becomes

$$\frac{R}{X}=\frac{l+\alpha}{100-l+\beta}.$$

If the null point is at $l_1$ with $R$ on the left, and at $l_2$ after $R$ and $X$ are interchanged, then

$$l_1+l_2=100+\beta-\alpha .$$

Without end errors $l_2=100-l_1$. Interchanging and averaging the two values of $X$ reduces the effect of unequal end errors; to find $\alpha$ and $\beta$ themselves, balance two known resistances, interchange them, and solve the two balance equations.

Proof of the sum rule. From the first equation, $l_1=\dfrac{R(100+\beta)-X\alpha}{R+X}$; after interchanging, $X$ is on the left and $l_2=\dfrac{X(100+\beta)-R\alpha}{R+X}$. Adding, the numerators give $(R+X)(100+\beta)-(R+X)\alpha$, so $l_1+l_2=100+\beta-\alpha$. The end errors belong to the ends of the wire, not to the resistors, which is why $\alpha$ stays with the left end when $R$ and $X$ swap places.

Good practice with the metre bridge. Choose $R$ so that the null point lies between about $40\ \text{cm}$ and $60\ \text{cm}$. Press the jockey gently onto the wire and lift it again — never slide it while pressed, which scrapes the wire and makes it non-uniform. Keep the current on only while taking a reading. Take readings with $R$ and $X$ in both gaps. The resistivity of the material of a wire is found by placing a measured length $L$ of it in the right gap: $X$ from the bridge, the diameter $d$ from a screw gauge at several places, and $\rho=\dfrac{X\pi d^2}{4L}$. That experiment belongs to the JEE Main experimental-skills unit, and is revisited in Section 20.2.

✏️ Example 5 — Measuring a coil and a wire
A $4.0\ \Omega$ resistance is placed in the left gap of a metre bridge and an unknown coil $X$ in the right gap. The null point is $40.0\ \text{cm}$ from the left end. (a) Find $X$. (b) A $6.0\ \Omega$ resistor is connected in parallel with $X$. Where is the new null point? (c) The coil is a wire of length $50.0\ \text{cm}$ and diameter $0.40\ \text{mm}$. Find the resistivity of its material. (d) If the null point can be located only to within $\pm0.1\ \text{cm}$, find the percentage uncertainty in $X$ from (a).
(a) $X=R\,\dfrac{100-l}{l}=4.0\times\dfrac{60.0}{40.0}=6.0\ \Omega$.
(b) $6.0\parallel6.0=3.0\ \Omega$ in the right gap: $\dfrac{4.0}{3.0}=\dfrac{l}{100-l}$, so $l=\dfrac{100\times4.0}{7.0}=57.1\ \text{cm}$ — the null moves away from the left gap, towards the gap whose resistance fell.
(c) $A=\dfrac{\pi d^2}{4}=\pi(0.20\times10^{-3})^2=1.257\times10^{-7}\ \text{m}^2$. $\rho=\dfrac{XA}{L}=\dfrac{6.0\times1.257\times10^{-7}}{0.500}=1.51\times10^{-6}\ \Omega\,\text{m}$ — typical of a heating alloy.
(d) $\dfrac{\Delta X}{X}=\dfrac{100\times0.1}{40\times60}=4.2\times10^{-3}=0.42\%$.
⏱ Shortcut For (b) use $l=\dfrac{100R}{R+X}$ directly: $\dfrac{400}{7}=57.1\ \text{cm}$.
✏️ Example 6 — Finding the end errors
To calibrate a metre bridge, a $2.0\ \Omega$ resistance is put in the left gap and a $3.0\ \Omega$ resistance in the right gap; the null point is at $40.2\ \text{cm}$. When the two are interchanged, the null point is at $60.8\ \text{cm}$. (a) Find the end errors $\alpha$ (left end) and $\beta$ (right end). (b) With a $5.0\ \Omega$ resistance in the left gap and an unknown $X$ in the right gap, the null point of the same bridge is at $52.0\ \text{cm}$. Find $X$, with and without the end corrections.
Find both end errors before you open the solution:
Sum rule $l_1+l_2=101.0=100+\beta-\alpha$, so $\beta-\alpha=1.0\ \text{cm}$.
First balance $\dfrac{2.0}{3.0}=\dfrac{40.2+\alpha}{59.8+\beta}$: $120.6+3\alpha=119.6+2\beta$, i.e. $3\alpha-2\beta=-1.0$. With $\beta=\alpha+1.0$: $3\alpha-2\alpha-2.0=-1.0$, so $\alpha=1.0\ \text{cm}$ and $\beta=2.0\ \text{cm}$.
Check Second balance: $\dfrac{60.8+1.0}{39.2+2.0}=\dfrac{61.8}{41.2}=1.50=\dfrac{3.0}{2.0}$ ✓.
(b) Corrected: $X=R\,\dfrac{100-l+\beta}{l+\alpha}=5.0\times\dfrac{50.0}{53.0}=4.72\ \Omega$. Uncorrected: $5.0\times\dfrac{48.0}{52.0}=4.62\ \Omega$ — about $2\%$ low.
⏱ Shortcut In end-error problems, find $\beta-\alpha$ from $l_1+l_2-100$ first; then one balance equation gives the rest.

In Interactive 2 put $R=4.0\ \Omega$ in the left gap with coil $X_1$ ($6.0\ \Omega$). With no end errors the null point is at $40.0\ \text{cm}$. Now set the left end error $\alpha=2.0\ \text{cm}$ (keep $\beta=0$). Where is the new null point, and what value of $X$ does a student who ignores end errors calculate?

With $\alpha=2.0\ \text{cm}$ the readouts show the null at $l_0=38.8\ \text{cm}$, from $\dfrac{4.0}{6.0}=\dfrac{l+2.0}{100-l}$, i.e. $l_0=\dfrac{400-12}{10}$. Ignoring the end error gives $X=4.0\times61.2/38.8=6.31\ \Omega$, an error of $+5.2\%$. The extra resistance at the left end acts like extra wire on that side, so less real wire is needed there and the null moves towards the end with the error. Press "⇄ Interchange": the null moves to $59.2\ \text{cm}$ and the uncorrected value becomes $5.80\ \Omega$; their mean, $6.06\ \Omega$, is much closer to the truth.
Interactive 2 — Metre Bridge: Null Point and End Errors

A known resistance $R$ and an unknown coil $X$ sit in the two gaps; a $2\ \text{V}$ cell drives the $100\ \text{cm}$ wire and a galvanometer joins the central strip to the jockey. Move the jockey (or press Play to sweep it) and watch the needle pass through zero. Add end errors $\alpha$, $\beta$ and see how far the uncorrected answer $X=R(100-l)/l$ drifts; interchange $R$ and $X$ to compare.

4.0 Ω0.0 cm0.0 cm30.0 cm
galvanometer—
null point $l_0$—
$X$ ignoring end errors—
error in $X$—
⚠️ JEE Main traps

1. Which length goes with which resistor. In the metre bridge the length $l$ is measured from the end next to the gap that holds the resistance in the numerator: $\dfrac{\text{left gap}}{\text{right gap}}=\dfrac{l}{100-l}$ with $l$ from the left end. Read the question for which gap holds the unknown — writing $X=Rl/(100-l)$ when $X$ is in the right gap inverts the answer.

2. Pairing the arms across the diagonal. The balance ratio compares the two arms of the same path ($P/Q$ along $A\to B\to C$ with $R/S$ along $A\to D\to C$). $P/S=R/Q$ is wrong.

3. Things that do not affect the balance. The emf and internal resistance of the cell, the galvanometer's resistance, interchanging the cell and galvanometer, and scaling all four arms by the same factor leave the null point where it is. They change only the size of the off-balance deflection.

4. Deleting a resistor that does carry current. The middle arm may be removed only when the bridge is balanced (or when symmetry proves its ends equipotential). For an unbalanced bridge, use node potentials.

5. End errors stay with the ends. When $R$ and $X$ are interchanged, the left-end error $\alpha$ is still added to the left length: $l_1+l_2=100+\beta-\alpha$, not $100$. And the best null point is near the middle of the wire, where $\Delta X/X=100\,\Delta l/[l(100-l)]$ is smallest.

A $3.0\ \Omega$ resistance is in the left gap of a metre bridge and an unknown $X$ in the right gap. The null point is $60.0\ \text{cm}$ from the left end. Then $X$ is

Exercises

Cells are ideal unless an internal resistance is given. In a metre bridge, $l$ is measured from the left end, and there are no end errors unless they are mentioned.

I
The balance condition.
  • 1 In a Wheatstone bridge $P=5.0\ \Omega$, $Q=10\ \Omega$ and $R=8.0\ \Omega$. Find $S$ for balance.
  • 2 Show that a bridge with $P=12\ \Omega$, $Q=18\ \Omega$, $R=20\ \Omega$, $S=30\ \Omega$ is balanced, and find its equivalent resistance between the cell terminals $A$ and $C$.
  • 3 A balanced bridge has $P=4.0\ \Omega$, $Q=8.0\ \Omega$, $R=6.0\ \Omega$, $S=12\ \Omega$ and a $6.0\ \text{V}$ cell. Find the current in each path and the current drawn from the cell.
  • 4 Using potentials, explain why a balanced bridge stays balanced when the cell and the galvanometer are interchanged.
  • 5 The ratio arms of a bridge are set to $P=100\ \Omega$, $Q=10\ \Omega$, and balance is found with $R=46\ \Omega$. Find $S$.
  • 6 Give two reasons why a null method measures resistance more accurately than an ammeter–voltmeter method.
  • 7 A bridge with $P=10\ \Omega$, $Q=20\ \Omega$, $R=15\ \Omega$, $S=30\ \Omega$ is balanced. $S$ is then changed to $40\ \Omega$. In which direction does current flow through the galvanometer, $B\to D$ or $D\to B$?
  • 8 In a bridge $P=2.0\ \Omega$, $Q=3.0\ \Omega$, $R=4.0\ \Omega$; balance is obtained only when a $12\ \Omega$ resistor is connected in parallel with $S$. Find $S$.
1 $S=\dfrac{QR}{P}=\dfrac{10\times8.0}{5.0}=16\ \Omega$.
2 $\dfrac{12}{18}=\dfrac{20}{30}=0.667$ ✓. $R_{\text{eq}}=\dfrac{(12+18)(20+30)}{12+18+20+30}=\dfrac{30\times50}{80}=18.75\ \Omega$.
3 Upper path $\dfrac{6.0}{12}=0.50\ \text{A}$, lower path $\dfrac{6.0}{18}=0.333\ \text{A}$; cell current $0.833\ \text{A}$ ($R_{\text{eq}}=7.2\ \Omega$ ✓).
4 With the cell across $BD$, balance needs $V_A=V_C$. From $B$ the paths to $D$ are $B\to A\to D$ ($P$ then $R$) and $B\to C\to D$ ($Q$ then $S$); equal potentials at $A$ and $C$ need $\dfrac{P}{R}=\dfrac{Q}{S}$, i.e. $PS=QR$ — the same condition.
5 $S=\dfrac{QR}{P}=\dfrac{10\times46}{100}=4.6\ \Omega$ — a $10:1$ ratio lets a resistance box in whole ohms measure tenths of an ohm.
6 At balance the galvanometer carries no current, so its resistance and calibration do not enter; the result is independent of the cell's emf; and the answer depends only on standard resistors, which can be made very accurate. (No meter draws current from the circuit being measured.)
7 $V_B=\varepsilon\dfrac{Q}{P+Q}=0.667\varepsilon$, $V_D=\varepsilon\dfrac{S}{R+S}=\dfrac{40}{55}\varepsilon=0.727\varepsilon$. $D$ is higher, so the current flows $D\to B$ (also: $QR-PS=300-400\lt0$).
8 $S\parallel12=\dfrac{QR}{P}=6.0\ \Omega$: $\dfrac{12S}{S+12}=6$ gives $S=12\ \Omega$.
II
Unbalanced bridges and sensitivity.
  • 1 In a bridge $P=Q=R=10\ \Omega$, $S=20\ \Omega$, $G=10\ \Omega$, with a $6.0\ \text{V}$ cell. Find the galvanometer current (in mA) and its direction.
  • 2 For the bridge of part 1 find the current drawn from the cell and the equivalent resistance between $A$ and $C$.
  • 3 The galvanometer is removed from a bridge with $P=10\ \Omega$, $Q=20\ \Omega$, $R=20\ \Omega$, $S=10\ \Omega$ and a $12\ \text{V}$ cell. Find $V_B-V_D$.
  • 4 A bridge has all four arms $50\ \Omega$, a $50\ \Omega$ galvanometer and a $4.0\ \text{V}$ cell. Use Result 12.14 to estimate the galvanometer current (in $\mu$A) when one arm changes by $2.0\%$.
  • 5 Why is the cell key closed before the galvanometer key? Why is a high resistance put in series with the galvanometer at the start?
  • 6 To measure a resistance of about $100\ \Omega$, which ratio arms would you choose: $10:10$, $100:100$ or $1000:1000$? Explain.
  • 7 In a bridge $P=4.0\ \Omega$, $Q=2.0\ \Omega$, $R=2.0\ \Omega$, $S=4.0\ \Omega$, $G=4.0\ \Omega$ and a $10\ \text{V}$ cell. Find the galvanometer current and its direction.
  • 8 Using the general formula for $I_g$, show that if $PS=QR$ the galvanometer current is zero whatever the value of $G$, and explain why a larger $G$ makes the bridge less sensitive.
1 $V_A=6$, $V_C=0$. At $B$: $\dfrac{V_B-6}{10}+\dfrac{V_B}{10}+\dfrac{V_B-V_D}{10}=0\Rightarrow3V_B-V_D=6$. At $D$: $\dfrac{V_D-6}{10}+\dfrac{V_D}{20}+\dfrac{V_D-V_B}{10}=0\Rightarrow5V_D-2V_B=12$. So $V_B=\tfrac{42}{13}=3.23\ \text{V}$, $V_D=\tfrac{48}{13}=3.69\ \text{V}$, and $I_g=\dfrac{V_D-V_B}{10}=0.0462\ \text{A}=46.2\ \text{mA}$ from $D$ to $B$.
2 $I=\dfrac{6-3.23}{10}+\dfrac{6-3.69}{10}=0.277+0.231=0.508\ \text{A}$; $R_{\text{eq}}=\dfrac{6.0}{0.508}=11.8\ \Omega$.
3 No bridging current: $V_B=12\times\dfrac{20}{30}=8.0\ \text{V}$, $V_D=12\times\dfrac{10}{30}=4.0\ \text{V}$; $V_B-V_D=4.0\ \text{V}$.
4 $|I_g|\approx\dfrac{\varepsilon\delta}{4(G+R_0)}=\dfrac{4.0\times0.020}{4\times100}=2.0\times10^{-4}\ \text{A}=200\ \mu\text{A}$ (exact value $198\ \mu\text{A}$).
5 When a circuit is switched on, the currents take a moment to settle (the circuit has some self-inductance and capacitance), so a galvanometer already connected can be jolted even at balance; closing the cell key first lets the currents settle. The series resistance limits the galvanometer current while the bridge is far from balance, protecting the coil; it is removed near the null to restore sensitivity.
6 $100:100$. The bridge is most sensitive when all four arms are of the same order as the unknown (Result 12.14); $10:10$ and $1000:1000$ also balance, but less sharply.
7 Half-turn symmetry: $V_D=10-V_B$. At $B$: $\dfrac{V_B-10}{4}+\dfrac{V_B}{2}+\dfrac{2V_B-10}{4}=0\Rightarrow5V_B=20$, $V_B=4.0\ \text{V}$, $V_D=6.0\ \text{V}$. $I_g=\dfrac{2.0}{4.0}=0.50\ \text{A}$ from $D$ to $B$.
8 The numerator is $\varepsilon(QR-PS)=0$ and the denominator is positive for every $G$, so $I_g=0$. Off balance, $G$ appears in the term $G(P+Q)(R+S)$ of $\Delta$: a larger $G$ makes $|I_g|$ smaller for the same mismatch.
III
Networks and symmetry.
  • 1 Find the equivalent resistance between $A$ and $B$: $3.0\ \Omega$ ($A$–$C$), $6.0\ \Omega$ ($C$–$B$), $4.0\ \Omega$ ($A$–$D$), $8.0\ \Omega$ ($D$–$B$), $7.0\ \Omega$ ($C$–$D$).
  • 2 Five equal resistors $r$ form a bridge (four in a diamond, one across the middle). Find the equivalent resistance between the other two corners.
  • 3 Four $4.0\ \Omega$ resistors form a square $ABCD$, and a fifth $4.0\ \Omega$ resistor joins $A$ to $C$. Find the equivalent resistance between $B$ and $D$.
  • 4 For the network of part 3, find the equivalent resistance between $A$ and $C$.
  • 5 Twelve $8.0\ \Omega$ resistors form the edges of a cube. Find the equivalent resistance between the ends of a face diagonal.
  • 6 Twelve $24\ \Omega$ resistors form the edges of a cube. Find the equivalent resistance between the two ends of one edge.
  • 7 Six $10\ \Omega$ resistors form a regular hexagon, and six more $10\ \Omega$ resistors join each corner to the centre. Find the equivalent resistance between two opposite corners.
  • 8 A bridge has $P=1.0\ \Omega$, $Q=2.0\ \Omega$, $R=2.0\ \Omega$, $S=1.0\ \Omega$ with a $1.0\ \Omega$ resistor across the middle. Find the equivalent resistance between $A$ and $C$.
1 $\dfrac36=\dfrac48$: balanced, so the $7.0\ \Omega$ is idle. $\dfrac{9\times12}{21}=5.14\ \Omega$.
2 Balanced ($r/r=r/r$): two paths of $2r$ in parallel give $r$.
3 Line $BD$ is a mirror line through the terminals; $A$ and $C$ are images, so $V_A=V_C$ and the diagonal carries no current. Paths $B\to A\to D$ and $B\to C\to D$, each $8.0\ \Omega$, in parallel: $4.0\ \Omega$.
4 Now $B$ and $D$ are images in line $AC$ and the paths are $4.0\ \Omega$ (diagonal), $8.0\ \Omega$ and $8.0\ \Omega$ in parallel: $\dfrac{1}{R}=\dfrac14+\dfrac18+\dfrac18$, $R=2.0\ \Omega$.
5 Put $A=(0,0,0)$, $B=(1,1,0)$, $V_A=V$, $V_B=0$. The plane that swaps $A$ and $B$ contains $(1,0,0)$, $(0,1,0)$, $(1,0,1)$, $(0,1,1)$: all at $V/2$. Corner $(0,0,1)$ at potential $c$ joins $A$ ($V$) and two corners at $V/2$: $3c=2V$, $c=\tfrac23V$. Current out of $A$: $2\times\dfrac{V/2}{r}+\dfrac{V/3}{r}=\dfrac{4V}{3r}$, so $R=\tfrac34r=6.0\ \Omega$.
6 $A=(0,0,0)$, $B=(1,0,0)$. By mirror symmetry $(0,1,0)$ and $(0,0,1)$ share a potential $a$; call $(0,1,1)$'s potential $b$; their images across the swapping plane have $V-a$ and $V-b$. Junction at $(0,1,0)$: $3a=V+b+(V-a)$; at $(0,1,1)$: $3b=2a+(V-b)$. So $b=\tfrac47V$, $a=\tfrac9{14}V$. Current out of $A$: $\dfrac Vr+2\,\dfrac{V-a}{r}=\dfrac{12V}{7r}$, $R=\tfrac7{12}r=14\ \Omega$.
7 Corners $0$ (at $V$) to $3$ (at $0$); the centre lies on the swapping plane, at $V/2$. Corners $1$ and $5$ share potential $x$; corners $2$, $4$ are at $V-x$. Junction at corner $1$: $3x=V+(V-x)+\tfrac V2$, $x=\tfrac58V$. Current out of corner $0$: $2\times\dfrac{3V/8}{r}+\dfrac{V/2}{r}=\dfrac{5V}{4r}$, so $R=0.8r=8.0\ \Omega$.
8 Unbalanced ($1\times1\ne2\times2$). Half-turn symmetry: $V_D=V-V_B$. Junction at $B$: $\dfrac{V_B-V}{1}+\dfrac{V_B}{2}+\dfrac{2V_B-V}{1}=0\Rightarrow V_B=\tfrac47V$. Current from $A$: $\dfrac{V-\tfrac47V}{1}+\dfrac{V-\tfrac37V}{2}=\tfrac37V+\tfrac27V=\tfrac57V$, so $R=1.4\ \Omega$.
IV
The metre bridge.
  • 1 With $5.0\ \Omega$ in the left gap, the null point is at $62.5\ \text{cm}$. Find the resistance in the right gap.
  • 2 $R=8.0\ \Omega$ is in the left gap and $X=12\ \Omega$ in the right gap. Where is the null point?
  • 3 The null point is at $45.0\ \text{cm}$. Where will it be when the two resistances are interchanged (no end errors)?
  • 4 A wire $80.0\ \text{cm}$ long and $0.50\ \text{mm}$ in diameter, placed in the right gap, has a measured resistance of $4.8\ \Omega$. Find the resistivity of its material.
  • 5 The null point is at $25.0\ \text{cm}$ and can be read to $\pm0.1\ \text{cm}$. Find the percentage uncertainty in the unknown resistance. What would it be with the null at $50.0\ \text{cm}$?
  • 6 Why is the bridge wire made of manganin or constantan, and why are the strips made of thick copper?
  • 7 With $4.0\ \Omega$ in the left gap and $6.0\ \Omega$ in the right gap the null point is at $40.3\ \text{cm}$; after interchanging, it is at $60.7\ \text{cm}$. Find the end errors $\alpha$ and $\beta$.
  • 8 With $R$ in the left gap and $X$ in the right gap the null point is at $40.0\ \text{cm}$. When a $30\ \Omega$ resistor is connected in parallel with $X$, the null point moves to $50.0\ \text{cm}$. Find $X$ and $R$.
  • 9 A student finds the galvanometer deflects the same way wherever the jockey touches the wire. Suggest two possible faults.
1 $X=5.0\times\dfrac{37.5}{62.5}=3.0\ \Omega$.
2 $l=\dfrac{100R}{R+X}=\dfrac{800}{20}=40.0\ \text{cm}$.
3 The ratio inverts, so the null moves to $100-45.0=55.0\ \text{cm}$.
4 $A=\pi(0.25\times10^{-3})^2=1.963\times10^{-7}\ \text{m}^2$; $\rho=\dfrac{4.8\times1.963\times10^{-7}}{0.800}=1.18\times10^{-6}\ \Omega\,\text{m}$.
5 $\dfrac{100\times0.1}{25\times75}=5.3\times10^{-3}=0.53\%$. At $50\ \text{cm}$: $\dfrac{10}{2500}=0.40\%$ — the middle of the wire is best.
6 The alloy has a high resistivity (a metre has a useful resistance) and a very small temperature coefficient (its resistance hardly changes as current warms it), so the wire stays uniform and constant. Thick copper strips have negligible resistance, so the only arms are $R$, $X$ and the two parts of the wire.
7 $\beta-\alpha=40.3+60.7-100=1.0\ \text{cm}$. First balance: $\dfrac{4.0}{6.0}=\dfrac{40.3+\alpha}{59.7+\beta}$: $241.8+6\alpha=238.8+4\beta=238.8+4\alpha+4.0$, so $2\alpha=1.0$: $\alpha=0.5\ \text{cm}$, $\beta=1.5\ \text{cm}$.
8 First: $\dfrac RX=\dfrac{40}{60}$, $X=1.5R$. Second: $R=X\parallel30$ (null at the middle). So $\dfrac{30X}{30+X}=\dfrac X{1.5}$, giving $30+X=45$: $X=15\ \Omega$, $R=10\ \Omega$.
9 Possible faults: a broken or loose connection in one gap or one copper strip (so one arm is effectively infinite); $R$ chosen so far from $X$ that the null lies beyond the wire; the galvanometer connected to the wrong terminal (e.g. to an end of the wire instead of the central strip); or the cell connected across the gaps instead of across the wire ends.
🎯 Exam corner JEE Main · MCQJEE Main · Numerical

E1. JEE Main · MCQ Between terminals $A$ and $B$ a $6\ \Omega$ resistor joins $A$ to $C$, a $3\ \Omega$ resistor joins $C$ to $B$, a $4\ \Omega$ resistor joins $A$ to $D$, a $2\ \Omega$ resistor joins $D$ to $B$, and a $9\ \Omega$ resistor joins $C$ to $D$. The equivalent resistance between $A$ and $B$ is (A) $2.0\ \Omega$ (B) $2.4\ \Omega$ (C) $3.6\ \Omega$ (D) $5.4\ \Omega$

Test Along the paths: $\dfrac63=\dfrac42=2$ — a balanced bridge; the $9\ \Omega$ carries no current.
Combine $(6+3)\parallel(4+2)=\dfrac{9\times6}{15}=3.6\ \Omega$.
Answer (C).
⏱ Shortcut Treat the $9\ \Omega$ as a plain wire instead: $(6\parallel4)+(3\parallel2)=2.4+1.2=3.6\ \Omega$ — the same, as it must be for a balanced bridge. Option (B) stops after the first parallel pair.

E2. JEE Main · Numerical In a metre bridge a resistance $R$ is in the left gap and an unknown resistance $X$ in the right gap; the null point is $40\ \text{cm}$ from the left end. When a $10\ \Omega$ resistor is connected in series with $X$, the null point shifts to $32\ \text{cm}$. Find $X$ in ohm. Give the answer to the nearest integer.

First $\dfrac RX=\dfrac{40}{60}$, so $X=1.5R$.
Second $\dfrac{R}{X+10}=\dfrac{32}{68}$, so $X+10=2.125R$. Subtracting, $10=0.625R$: $R=16\ \Omega$ and $X=24\ \Omega$.
Answer $24$.
⏱ Shortcut Check: $l=\dfrac{100R}{R+X}$ gives $\dfrac{1600}{40}=40$ and $\dfrac{1600}{50}=32$ ✓.

E3. JEE Main · MCQ A Wheatstone bridge with arms $P$, $Q$ (meeting at $B$) and $R$, $S$ (meeting at $D$) is balanced. Which one of the following changes makes the galvanometer deflect? (A) doubling the emf of the cell (B) interchanging the cell and the galvanometer (C) doubling both $P$ and $R$ (D) doubling both $P$ and $S$

Condition Balance needs $PS=QR$, independent of the emf (A) and symmetric under interchanging cell and galvanometer (B).
Scaling (C): $2P\cdot S=Q\cdot2R$ — still balanced. (D): $2P\cdot2S=4PS\ne QR$ — unbalanced.
Answer (D).
⏱ Shortcut Write the condition as $P\cdot S=Q\cdot R$. Scaling one arm on each side of this equation by the same factor keeps the balance; scaling both arms on the same side does not.

E4. JEE Main · Numerical In a bridge $ABCD$, $P=30\ \Omega$ ($A$–$B$), $Q=10\ \Omega$ ($B$–$C$), $R=10\ \Omega$ ($A$–$D$), $S=30\ \Omega$ ($D$–$C$), and a $30\ \Omega$ resistor joins $B$ and $D$. An ideal $24\ \text{V}$ cell is connected across $A$ and $C$. Find the equivalent resistance of the network between $A$ and $C$, in ohm. Give the answer to the nearest integer.

Symmetry Unbalanced ($PS=900\ne QR=100$). A half-turn swaps $A\leftrightarrow C$, $B\leftrightarrow D$ and maps $P\leftrightarrow S$, $Q\leftrightarrow R$, so $V_D=24-V_B$.
Junction at $B$ $\dfrac{V_B-24}{30}+\dfrac{V_B}{10}+\dfrac{2V_B-24}{30}=0$: $6V_B=48$, $V_B=8\ \text{V}$, $V_D=16\ \text{V}$.
Current From $A$: $\dfrac{24-8}{30}+\dfrac{24-16}{10}=0.533+0.800=1.333\ \text{A}$; $R_{\text{eq}}=\dfrac{24}{1.333}=18\ \Omega$.
Answer $18$.
⏱ Shortcut Look for the half-turn symmetry ($P=S$, $Q=R$): it reduces an unbalanced bridge to one unknown potential.

E5. JEE Main · MCQ In a metre bridge with end errors $\alpha$ at the left end and $\beta$ at the right end, the null point is at $38.0\ \text{cm}$ with $R$ in the left gap and $X$ in the right gap, and at $63.0\ \text{cm}$ when they are interchanged. Then $\beta-\alpha$ is (A) $1.0\ \text{cm}$ (B) $-1.0\ \text{cm}$ (C) zero (D) $25.0\ \text{cm}$

Rule Adding $l_1=\dfrac{R(100+\beta)-X\alpha}{R+X}$ and $l_2=\dfrac{X(100+\beta)-R\alpha}{R+X}$ gives $l_1+l_2=100+\beta-\alpha$.
Numbers $38.0+63.0=101.0$, so $\beta-\alpha=1.0\ \text{cm}$.
Answer (A).
⏱ Shortcut Without end errors $l_1+l_2=100$ exactly; any excess is $\beta-\alpha$. (C) would need $l_1+l_2=100$; (D) is $l_2-l_1$.

E6. JEE Main · Numerical Twelve identical resistors of $12\ \Omega$ each form the edges of a cube. Find the equivalent resistance, in ohm, between the two ends of one edge. Give the answer to the nearest integer.

Symmetry $V_A=V$, $V_B=0$ at the ends of the edge. The two other neighbours of $A$ share a potential $a$ (mirror symmetry); the corner diagonally opposite $A$ on their face has $b$; their images across the plane that swaps $A$ and $B$ have $V-a$ and $V-b$.
Junctions $3a=V+b+(V-a)$ and $3b=2a+(V-b)$ give $b=\tfrac47V$, $a=\tfrac9{14}V$.
Current $I=\dfrac Vr+2\,\dfrac{V-a}{r}=\dfrac Vr\left(1+\dfrac57\right)=\dfrac{12V}{7r}$, so $R=\dfrac7{12}r=7\ \Omega$.
Answer $7$.
⏱ Shortcut Learn the cube triple: body diagonal $\tfrac56r$, face diagonal $\tfrac34r$, edge $\tfrac7{12}r$ — the closer the terminals, the smaller the resistance.
🔬 Research–Teaching NexusResearch-tutored · optional, about 60 minutes

Research question. Can a home-built Wheatstone bridge work as a thermometer? How precisely can it detect the change in resistance of a coil of copper wire as it is warmed, and what temperature coefficient does it give for copper?

Why it matters. Bridges are the hidden heart of a great many sensors. Platinum resistance thermometers in hospitals, food factories and weather stations, the strain gauges glued to bridges, aircraft wings and wind-turbine blades, and the load cells in every electronic weighing scale all sit in a bridge circuit, because a balanced bridge turns a tiny fractional change of resistance into a clean signal measured from zero (Result 12.14). Engineers choose the arms, the supply voltage and the detector exactly as you will.

What to do.

  1. Wind about $5$–$10\ \text{m}$ of thin enamelled copper wire into a small coil (resistance a few ohms) and seal it in a thin plastic bag. Measure its resistance at room temperature with a metre bridge, keeping the null between $40$ and $60\ \text{cm}$.
  2. Place the coil in a beaker of water with a thermometer. Heat the water in steps of about $10^\circ\text{C}$ up to $70^\circ\text{C}$, stirring, and find the null point at each temperature. Keep the current on only while you take a reading.
  3. Calibrate the end errors of your bridge first by balancing two known resistors and interchanging them (Result 12.17), and correct every reading.
  4. Plot $R$ against temperature, find the slope and the temperature coefficient $\alpha_{\text{Cu}}=\dfrac{1}{R_0}\dfrac{dR}{dT}$, and compare with the accepted value of about $0.0039\ \text{K}^{-1}$.
  5. Estimate the smallest temperature change your bridge can detect from the smallest jockey movement that visibly moves the galvanometer.

Tools: Metre bridge, galvanometer, cell and key, resistance box, enamelled copper wire, beaker, heater, thermometer, screw gauge (optional, to estimate the wire's resistivity as a cross-check).

Hand in: A table of null points, corrected resistances and temperatures; the graph with its slope; your value of $\alpha_{\text{Cu}}$ with an uncertainty; and a paragraph on the largest sources of error.

Going further. Replace the metre bridge by a four-arm bridge of fixed $10\ \Omega$ resistors with the coil as the fourth arm, balanced at room temperature, and record the out-of-balance galvanometer deflection as the water warms. Is it proportional to the temperature rise, as Result 12.14 predicts for small changes?

Instructor note: the coil's leads add resistance that does not change with temperature; students should measure it (short the coil) or use thick leads. Typical results lie within $5$–$10\%$ of $0.0039\ \text{K}^{-1}$ if the end errors are corrected and the wire is not heated by the measuring current. Good discussion point: why the bridge wire itself must be manganin, not copper.

🧪 Self-check quiz

0/5 correct

Q1. The balance condition of a Wheatstone bridge does not depend on

Q2. In a metre bridge a known $R$ is in the left gap, an unknown $X$ in the right gap, and the null point is at $l\ \text{cm}$ from the left end. Then $X$ equals

Q3. A metre-bridge measurement is most accurate when the null point is

Q4. Five equal resistors $r$ form a bridge: four make a diamond $ABCD$ and the fifth joins $B$ and $D$. The equivalent resistance between $A$ and $C$ is

Q5. The wire of a metre bridge is made of manganin rather than copper mainly because manganin has