Chapter 20 · Experimental Skills

20.2 Electricity, Optics and Electronics Experiments

The JEE Main experiments in electricity, optics and electronics: resistivity with a metre bridge, Ohm's law, a galvanometer's resistance and figure of merit by half deflection, focal lengths by the u–v method, the i–δ curve of a prism, refractive index with a travelling microscope, diode and Zener characteristics, and telling components apart.

Ask a JEE Main candidate why the null point of a metre bridge should be near the middle, why a galvanometer is shunted to half its deflection, how a convex mirror's focal length can be found when it never forms a real image, or how to tell an LED from a capacitor with a multimeter — and the ones who have thought through the experiments answer in seconds. The paper's experimental questions in electricity, optics and electronics are short, but they test exactly that understanding: which reading goes where, which graph is straight, and what the instrument's own resistance or the bench's index error does to the answer.

This section covers the nine experiments in electricity, optics and electronics in the syllabus, in the same format as Section 20.1: aim, apparatus, method, observation table, graph or calculation, and precautions and sources of error, with the theory linked to the section where it was taught — current electricity in Chapter 12 (12.1, 12.3), the galvanometer in Section 13.2, mirrors, lenses and prisms in 16.1 and 16.2, and semiconductor devices in Chapter 19 (19.1, 19.2).

Resistance experiments: metre bridge, Ohm's law and the galvanometer

All three experiments measure a resistance, each in a different way: by balancing a bridge (no current through the detector, so the meter's own properties drop out), by measuring $V$ and $I$ directly (where the meters' resistances matter), and by halving a deflection (where a large series resistance makes the circuit current nearly constant).

Experiment 1 — Resistivity of the material of a wire using a metre bridge

Aim. To find the resistance of a given wire with a metre bridge and hence the resistivity of its material. Apparatus. Metre bridge, galvanometer, resistance box, the wire, Leclanché cell (or a $2\ \text{V}$ cell), one-way key, jockey, screw gauge, metre scale, connecting wires.

From Section 12.3 (Law 12.16 and Result 12.17), with the known $R$ in the left gap, the wire $X$ in the right gap and the null point at $l$ cm from the left end, $X=R\,(100-l)/l$. Interchanging $R$ and $X$ and averaging removes the end errors.

📐 Result 20.10 — Resistivity with a metre bridge

If the null point is at $l_1$ with $R$ on the left and at $l_2$ (still measured from the left end) after interchanging $R$ and $X$,

$$X_1=R\,\frac{100-l_1}{l_1},\qquad X_2=R\,\frac{l_2}{100-l_2},\qquad X=\tfrac12(X_1+X_2),$$

and for a wire of length $L$ and diameter $d$, the resistivity is $\ \rho=\dfrac{\pi d^2X}{4L}$.

Method.

  1. Connect the wire (its whole measured length $L$ between the terminals) in the right gap and the resistance box in the left gap; the cell and key across the ends of the bridge wire; the galvanometer from the central strip to the jockey.
  2. Take a resistance $R$ from the box and touch the jockey near each end of the wire: the galvanometer should deflect in opposite directions. Find the null point $l_1$ by gentle touches (never sliding the jockey).
  3. Choose $R$ so that the null point lies between about $40$ and $60\ \text{cm}$. Repeat for three values of $R$.
  4. Interchange $R$ and $X$ and repeat to find $l_2$. Measure $L$ with a metre scale and $d$ with a screw gauge (several places, two directions).
$R$ ($\Omega$)$l_1$ (cm)$X_1$ ($\Omega$)$l_2$ (cm)$X_2$ ($\Omega$)mean $X$ ($\Omega$)
$2.0$$40.2$$2.975$$60.2$$3.025$$3.00$

Precautions and sources of error. Clean and tighten all connections (thick, short copper leads); keep the key closed only while taking a reading (the wire heats and its resistance changes); press the jockey gently and never slide it (it scrapes the wire and spoils its uniformity); keep the null point near the middle, where the error in $X$ is least. End resistances and a non-uniform bridge wire are the main systematic errors — interchanging $R$ and $X$ reduces them.

Experiment 2 — Resistance of a wire using Ohm's law

Aim. To find the resistance of a given wire by plotting a graph of potential difference against current. Apparatus. The wire, battery, rheostat, ammeter, voltmeter, key, connecting wires.

📐 Result 20.11 — Resistance from the $V$–$I$ graph

For an ohmic conductor at constant temperature, $V=IR$ (Section 12.1, Law 12.3): the $V$–$I$ graph is a straight line through the origin and $R=\dfrac{\Delta V}{\Delta I}$ is its slope. With the voltmeter (resistance $R_V$) connected directly across the wire, the ammeter also carries the voltmeter's current, so the measured value is

$$R_\text{meas}=\frac{R\,R_V}{R+R_V}\lt R,\qquad R=\frac{R_\text{meas}R_V}{R_V-R_\text{meas}},$$

which is close to $R$ only when $R_V\gg R$.

Method.

  1. Connect the battery, key, rheostat, ammeter and wire in series, and the voltmeter in parallel with the wire (positive terminals towards the positive of the battery).
  2. Note the least counts and zero errors of both meters.
  3. Adjust the rheostat to pass a small current; read $I$ and $V$. Increase the current in steps, taking five or six pairs of readings, and open the key between readings.
  4. Plot $V$ against $I$; find $R$ from the slope (using a large triangle on the line).
$I$ (A)$0.10$$0.20$$0.30$$0.40$
$V$ (V)$0.52$$1.04$$1.55$$2.08$

Slope $=\dfrac{2.08-0.52}{0.40-0.10}=5.2\ \Omega$.

Precautions and sources of error. Keep the current small and the key open between readings, so the wire does not heat up (its resistance rises with temperature and the graph curves); use meters of suitable range so the readings lie in the upper part of the scale; check for zero errors. A voltmeter of too low resistance makes $R$ too small (Result 20.11).

Experiment 3 — Resistance and figure of merit of a galvanometer by half deflection

Aim. To find the resistance $G$ of a moving-coil galvanometer by the half-deflection method and its figure of merit. Apparatus. Galvanometer, a cell of steady emf (accumulator), two resistance boxes (a high-resistance box $R$ up to $10\ \text{k}\Omega$ and a low-resistance box $S$), two keys, connecting wires.

📘 Definition 20.5 — Figure of merit of a galvanometer

The figure of merit $k$ of a galvanometer is the current needed to produce a deflection of one division: $k=I/\theta$, in A/div. It is the reciprocal of the current sensitivity (Section 13.2); a smaller figure of merit means a more sensitive galvanometer.

📐 Result 20.12 — Half-deflection method

A cell of emf $E$ (negligible internal resistance) drives a current through a resistance $R$ and the galvanometer $G$ in series, giving a deflection $\theta$. A shunt $S$ is then connected across the galvanometer and adjusted, keeping $R$ fixed, until the deflection is $\theta/2$. Then

$$G=\frac{R\,S}{R-S}\approx S\quad(R\gg S),\qquad k=\frac{E}{(R+G)\,\theta}.$$

Derivation. Without the shunt, $I_g=\dfrac{E}{R+G}$. With it, the total current is $\dfrac{E}{R+GS/(G+S)}$ and the galvanometer takes the fraction $\dfrac{S}{G+S}$ of it: $I_g'=\dfrac{ES}{R(G+S)+GS}$. Setting $I_g'=\tfrac12I_g$ gives $2S(R+G)=R(G+S)+GS$, i.e. $G(R-S)=RS$. Because $R$ is thousands of ohms and $S$ tens, connecting $S$ barely changes the circuit current, so half of it in the galvanometer means $S\approx G$ — hence the name.

Method.

  1. Connect the cell, key $K_1$, the high-resistance box $R$ and the galvanometer in series; connect the low-resistance box $S$ through key $K_2$ across the galvanometer.
  2. With $K_2$ open, take a large $R$ (several kilo-ohms) and adjust it to give an even-numbered deflection $\theta$ (say $30$ divisions).
  3. Close $K_2$ and adjust $S$ until the deflection is exactly $\theta/2$. Record $R$, $\theta$ and $S$. Repeat for several values of $R$.
  4. Calculate $G$ for each set, and $k$ from the first part of each set.
$R$ ($\Omega$)$\theta$ (div)$S$ ($\Omega$)$G=\dfrac{RS}{R-S}$ ($\Omega$)$k$ (A/div)
$5000$$30$$50$$50.5$$1.32\times10^{-5}$

Precautions and sources of error. Use a cell of steady emf and negligible internal resistance (an accumulator); keep $R$ much larger than $S$; take even-numbered deflections that are large (for better relative precision); do not change $R$ after closing $K_2$; tighten plugs in the resistance boxes. An internal resistance $r$ of the cell simply adds to $R$.

✏️ Example 1 — Resistivity with interchange of $R$ and $X$
A wire of length $0.80\ \text{m}$ and diameter $0.40\ \text{mm}$ is placed in the right gap of a metre bridge with $R=2.0\ \Omega$ in the left gap; the null point is at $40.2\ \text{cm}$ from the left end. When $R$ and the wire are interchanged, the null point is at $60.2\ \text{cm}$ from the left end. (a) Find the resistance of the wire from each reading and their mean. (b) Find the resistivity of the material. (c) What do the two readings tell you about the end errors?
(a) $X_1=2.0\times\dfrac{59.8}{40.2}=2.975\ \Omega$; $\ X_2=2.0\times\dfrac{60.2}{39.8}=3.025\ \Omega$; mean $X=3.00\ \Omega$.
(b) $\rho=\dfrac{\pi d^2X}{4L}=\dfrac{\pi(4.0\times10^{-4})^2\times3.00}{4\times0.80}=4.7\times10^{-7}\ \Omega\,\text{m}$ — a value typical of constantan.
(c) Without end errors $l_1+l_2=100\ \text{cm}$; here $l_1+l_2=100.4$, so $\beta-\alpha=0.4\ \text{cm}$ (Result 12.17): the right end has slightly more extra resistance. Averaging the two values of $X$ largely cancels this.
Check $R\lt X$ and the null point is left of the middle, as it must be: the smaller resistance gets the shorter length.
✏️ Example 2 — Half deflection and figure of merit
In the half-deflection method a $2.0\ \text{V}$ accumulator of negligible internal resistance and a resistance $R=5000\ \Omega$ give a deflection of $30$ divisions. A shunt of $50\ \Omega$ across the galvanometer reduces the deflection to $15$ divisions. (a) Find the galvanometer resistance exactly, and the percentage error made by taking $G=S$. (b) Find the figure of merit and the current sensitivity. (c) What series resistance would convert this galvanometer, with $30$ divisions on its scale, into a voltmeter reading up to $3.0\ \text{V}$?
Find $G$ in (a) before you open the solution:
(a) $G=\dfrac{RS}{R-S}=\dfrac{5000\times50}{4950}=50.5\ \Omega$. Taking $G=S=50\ \Omega$ is low by $1\%$.
(b) $I=\dfrac{E}{R+G}=\dfrac{2.0}{5050.5}=3.96\times10^{-4}\ \text{A}$, so $k=\dfrac{3.96\times10^{-4}}{30}=1.32\times10^{-5}\ \text{A/div}$; current sensitivity $1/k=7.6\times10^4\ \text{div/A}=76\ \text{div/mA}$.
(c) Full-scale current $I_g=30k=3.96\times10^{-4}\ \text{A}$. Series resistance $=\dfrac{3.0}{3.96\times10^{-4}}-50.5=7576-50.5\approx7.5\times10^3\ \Omega$ (Result 13.14).
⏱ Shortcut Whenever $R\ge100S$, write $G\approx S$ at once; the exact formula only shifts the answer by about $S/R$.

In the Ohm's-law experiment the voltmeter is connected directly across the wire and the ammeter in series with the pair. Compared with the true resistance of the wire, the value $V/I$ found is

Focal lengths by the u–v method

The optical bench experiments locate images with pins instead of a screen. Their key skill is removing parallax; their theory is the mirror and lens formulas of Section 16.1 (Law 16.5, $\tfrac1v+\tfrac1u=\tfrac1f$) and Section 16.2 (Law 16.11, $\tfrac1v-\tfrac1u=\tfrac1f$), always with the Cartesian sign convention: distances from the pole or optical centre, positive along the direction of the incident light.

📘 Definition 20.6 — Parallax and its removal

Parallax is the apparent relative shift of two objects at different distances when the eye moves sideways. An image pin is at the position of an image when there is no parallax between the tip of the pin and the tip of the image: moving the eye from side to side, the two tips stay together. If they separate, the one that moves with the eye is the farther one, and the pin is moved accordingly.

📐 Result 20.13 — Focal length by the u–v method

Concave mirror: $\dfrac1v+\dfrac1u=\dfrac1f$, $\ f=\dfrac{uv}{u+v}$. Convex lens: $\dfrac1v-\dfrac1u=\dfrac1f$, $\ f=\dfrac{uv}{u-v}$. Graphs (in magnitudes, for real images): $\dfrac1{|v|}$ against $\dfrac1{|u|}$ is a straight line of slope $-1$ cutting both axes at $\dfrac1{|f|}$; and the $|u|$–$|v|$ curve is a rectangular hyperbola which the line $|v|=|u|$ meets at $(2|f|,2|f|)$.

Convex mirror (with an auxiliary convex lens): the lens forms a real image $I$ of the object pin. The convex mirror, facing the lens, is placed between the lens and $I$ and moved until the light retraces its path and the image coincides with the object pin. Then $I$ is the mirror's centre of curvature: $R=MI$ (distance from mirror to $I$) and $f=R/2$.

Experiment 4 — Focal length of a concave mirror, a convex lens and a convex mirror

Aim. To find the focal length of a concave mirror and of a convex lens by plotting $u$–$v$ (or $1/u$–$1/v$) graphs, and of a convex mirror using a convex lens. Apparatus. Optical bench with uprights, the mirrors and lens in holders, two optical needles (object and image pins), an index rod, a knitting needle for rough focusing.

Method.

  1. Rough focal length. Form the image of a distant object (a window) on a wall: the distance from mirror or lens to the image is roughly $|f|$.
  2. Index correction. Place the index rod between the pole (or optical centre) and the tip of a pin and compare its true length with the difference of the bench readings; the difference is added to every observed distance.
  3. Concave mirror. Place the object pin beyond $F$ (between $F$ and $2F$, then beyond $2F$). Looking into the mirror, find the inverted image and move the image pin until there is no parallax between their tips. Record the positions; take six or more sets.
  4. Convex lens. Object pin on one side; look through the lens from the other side for the inverted image, and remove parallax with the image pin.
  5. Convex mirror. Use a convex lens to form a real image of the object pin and mark its position $I$. Put the convex mirror between lens and $I$ and slide it until the image seen back near the object pin shows no parallax with it. Then $R=$ distance from mirror to the old position of $I$.
Concave mirror: $u$ (cm)$-25.0$$-30.0$$-40.0$$-50.0$
$v$ (cm)$-100.4$$-59.6$$-40.2$$-33.4$
$f=uv/(u+v)$ (cm)$-20.0$$-20.0$$-20.0$$-20.0$

Precautions and sources of error. Align the tips of the pins with the pole (or optical centre) at the same height; remove parallax tip to tip, keeping the eye at least $25\ \text{cm}$ from the pin; apply the index correction; keep the mirror or lens upright and clean. Using only paraxial rays (small apertures) reduces aberration. Readings very close to $F$ give huge, uncertain $v$ and should be avoided.

✏️ Example 3 — A concave mirror and a convex lens on the bench
(a) The readings for a concave mirror are given in the table above. Find its focal length and check that $u=v$ gives $2f$. (b) For a convex lens, the image pins are found at $v=+60.4$, $+29.8$ and $+22.6\ \text{cm}$ for $u=-20.0$, $-30.0$ and $-45.0\ \text{cm}$. Find the focal length. (c) On the graph of $1/v$ against $1/u$ (with signs) for the lens, what are the slope and the intercepts?
(a) $f=\dfrac{uv}{u+v}$: $\dfrac{(-25.0)(-100.4)}{-125.4}=-20.0$, and similarly $-19.96$, $-20.05$, $-20.02\ \text{cm}$: mean $f=-20.0\ \text{cm}$. The reading $u=-40.0$, $v=-40.2$ is the point $u\approx v=2f$ ✓.
(b) $f=\dfrac{uv}{u-v}$: $\dfrac{(-20.0)(60.4)}{-80.4}=15.02$, $\dfrac{(-30.0)(29.8)}{-59.8}=14.95$, $\dfrac{(-45.0)(22.6)}{-67.6}=15.04$; mean $f=+15.0\ \text{cm}$.
(c) $\dfrac1v=\dfrac1u+\dfrac1f$: slope $+1$; the $1/v$-intercept is $1/f=0.0667\ \text{cm}^{-1}$ and the $1/u$-intercept is $-1/f$.
Check Signs: a concave mirror has $f\lt0$ and a real image in front ($v\lt0$); a convex lens has $f\gt0$ and a real image behind ($v\gt0$).
✏️ Example 4 — A convex mirror with the help of a lens
A convex lens of focal length $20\ \text{cm}$ forms a real image of an object pin at $50.0\ \text{cm}$ behind the lens. A convex mirror is then placed between the lens and that image, facing the lens, and moved until the image of the object pin formed by the light returning through the lens coincides with the pin itself. The mirror is then $30.0\ \text{cm}$ from the lens. (a) How far is the object pin from the lens? (b) Find the radius of curvature and focal length of the convex mirror. (c) Why is a lens needed at all?
Find the focal length of the convex mirror in (b) first:
(a) $\dfrac1u=\dfrac1v-\dfrac1f=\dfrac1{50}-\dfrac1{20}=-\dfrac{3}{100}$, so $u=-33.3\ \text{cm}$: the pin is $33.3\ \text{cm}$ in front of the lens.
(b) The light retraces its path, so it meets the mirror normally: the rays converging to $I$ are aimed at the mirror's centre of curvature. $R=50.0-30.0=20.0\ \text{cm}$, $f=R/2=+10.0\ \text{cm}$ (positive for a convex mirror in the Cartesian convention).
(c) A convex mirror forms only virtual images of real objects, which cannot be located with a pin in front of it. The lens supplies converging light — a virtual object behind the mirror — and the retracing condition pins down $C$.
⏱ Shortcut $f_\text{convex mirror}=\tfrac12(\text{lens-to-image distance}-\text{lens-to-mirror distance})$; the lens's focal length is not needed.

In Interactive 1 choose the convex lens, set $f=20\ \text{cm}$ and put the object pin $30\ \text{cm}$ from the lens. Where will the image pin show no parallax, and what is the magnification?

With $f=20\ \text{cm}$ and $u=-30\ \text{cm}$ the readouts show $v=+60.0\ \text{cm}$, $f=uv/(u-v)=+20.0\ \text{cm}$ and $m=v/u=-2.00$: a real, inverted, magnified image on the far side. From $\tfrac1v=\tfrac1u+\tfrac1f=-\tfrac1{30}+\tfrac1{20}=\tfrac1{60}$. ($12\ \text{cm}$ comes from adding $\tfrac1{20}+\tfrac1{30}$, the mirror formula used for a lens; a virtual image needs the object inside $F$.) On the graph the point lies on the straight line $\tfrac1{|u|}+\tfrac1{|v|}=\tfrac1{|f|}$.
Interactive 1 — The u–v Optical Bench

An object pin (green) stands on an optical bench in front of a convex lens or a concave mirror; two rays from its tip locate the image, where the image pin (red) would show no parallax. Below, each position you try is logged on the graph of $1/|v|$ against $1/|u|$ — a straight line that cuts both axes at $1/|f|$. Choose the element and $f$, move the object, or press Play to sweep it along the bench.

20 cm30 cm
$u$—
$v$—
$f$ from $u$, $v$—
magnification—

In the u–v experiment with a concave mirror, the image pin is moved until "there is no parallax". This means that

The prism and the glass slab

Two experiments measure refractive index: one from the deviation produced by a prism (Section 16.2, Result 16.13), the other from the apparent depth of a mark seen through a slab (Result 16.7), measured with the travelling microscope of Section 20.1.

📐 Result 20.14 — The $i$–$\delta$ curve of a prism

For a prism of angle $A$, with angle of incidence $i$ and angle of emergence $e$, the deviation is $\delta=i+e-A$. As $i$ increases, $\delta$ falls to a minimum $\delta_m$ and then rises; the curve is not symmetric (it rises more slowly on the large-$i$ side). At the minimum $i=e$, and

$$n=\frac{\sin\frac{A+\delta_m}{2}}{\sin\frac{A}{2}},\qquad i_\text{min}=\frac{A+\delta_m}{2}.$$

Every deviation above $\delta_m$ occurs for two angles of incidence, $i$ and $e$ (the path reversed).

Experiment 5 — Angle of deviation against angle of incidence for a prism

Aim. To plot the graph of the angle of deviation against the angle of incidence for a triangular glass prism, and to find its refractive index from the minimum deviation. Apparatus. Equilateral glass prism, drawing board, white sheet, pins, protractor, scale, drawing pins.

Method.

  1. Fix the sheet on the board and outline the prism, $ABC$. Draw a normal to face $AB$ and a line at the chosen angle of incidence $i$ (start near $35^\circ$).
  2. Fix two pins $P$, $Q$ on the incident line, at least $5\ \text{cm}$ apart. Looking through face $AC$, fix pins $R$, $S$ in line with the images of $P$ and $Q$.
  3. Remove the prism, draw the emergent ray $RS$, extend the incident and emergent rays to meet and measure the deviation $\delta$ (and $e$ as a check: $\delta=i+e-A$).
  4. Repeat for $i$ from about $35^\circ$ to $60^\circ$ in steps of $5^\circ$, with closer steps near the minimum. Plot $\delta$ against $i$; read $\delta_m$.
$i$ (°)$35$$40$$45$$48$$50$$55$$60$
$\delta$ (°)$41.0$$38.5$$37.4$$37.2$$37.2$$37.7$$38.9$

Precautions and sources of error. Keep the pins vertical and well separated ($\gt5\ \text{cm}$); look at the feet of the pins' images; use the same base position of the prism for every reading; avoid very small $i$ (no emergence or very faint rays). The minimum is flat, so read $\delta_m$ from a smooth curve, not a single point; pin positions and protractor readings (to $0.5^\circ$) are the main errors.

📐 Result 20.15 — Refractive index with a travelling microscope

If the microscope reads $R_1$ when focused on a mark on the base, $R_2$ when focused on the same mark seen through a slab placed over it, and $R_3$ when focused on the top surface of the slab, then real thickness $=R_3-R_1$, apparent thickness $=R_3-R_2$, and

$$n=\frac{\text{real thickness}}{\text{apparent thickness}}=\frac{R_3-R_1}{R_3-R_2},\qquad\text{normal shift }R_2-R_1=t\left(1-\frac1n\right).$$

Experiment 6 — Refractive index of a glass slab using a travelling microscope

Aim. To determine the refractive index of a glass slab using a travelling microscope. Apparatus. Travelling microscope, glass slab, a sheet with a fine ink cross (or lycopodium powder), spirit level.

Method.

  1. Level the microscope base and set the microscope vertical. Find the least count of its vertical scale.
  2. Focus on the cross mark on the base, eliminating parallax with the cross-wire: reading $R_1$.
  3. Place the slab over the mark without disturbing it. Raise the microscope (always upwards) to focus the mark seen through the glass: $R_2$.
  4. Sprinkle a little lycopodium powder on the top surface and raise the microscope to focus on it: $R_3$. Repeat the whole set three times.
$R_1$ (cm)$R_2$ (cm)$R_3$ (cm)real $R_3-R_1$ (cm)apparent $R_3-R_2$ (cm)$n$
$4.215$$4.795$$5.955$$1.740$$1.160$$1.50$

Precautions and sources of error. Move the microscope in one direction only (backlash); remove parallax between cross-wire and image at every focus; use a thin layer of powder; the slab should be thick (a thin slab gives a small apparent thickness with a large relative error). The precision is limited by the depth of focus of the microscope.

✏️ Example 5 — Reading the prism curve
The table of Experiment 5 was taken with an equilateral prism ($A=60^\circ$). (a) Estimate the minimum deviation and the angle of incidence at which it occurs, and hence the refractive index. (b) For $i=40^\circ$, find the angle of emergence, and say at what other angle of incidence the deviation would again be $38.5^\circ$. (c) For the slab readings in the table of Experiment 6, find the normal shift and check it against $t(1-1/n)$.
(a) The smooth curve bottoms out at $\delta_m\approx37.2^\circ$, between $i=48^\circ$ and $50^\circ$; theory gives $i_\text{min}=\tfrac12(A+\delta_m)=48.6^\circ$ ✓. $n=\dfrac{\sin48.6^\circ}{\sin30^\circ}=\dfrac{0.750}{0.5}=1.50$.
(b) $e=\delta+A-i=38.5+60-40=58.5^\circ$. By reversibility, $i=58.5^\circ$ also gives $\delta=38.5^\circ$ (with $e=40^\circ$) — consistent with the table, where $\delta$ at $55^\circ$ and $60^\circ$ brackets $38.5^\circ$.
(c) Normal shift $R_2-R_1=4.795-4.215=0.580\ \text{cm}$; $t(1-1/n)=1.740\times(1-1/1.50)=0.580\ \text{cm}$ ✓.
Check At $i=i_\text{min}$ the refraction angle inside is $r=A/2=30^\circ$ and $\sin48.6^\circ=1.5\sin30^\circ$ ✓ — the ray passes symmetrically.

With a travelling microscope, the readings are $R_1=2.000\ \text{cm}$ on a mark, $R_2=2.400\ \text{cm}$ on the mark seen through a slab, and $R_3=3.200\ \text{cm}$ on the top of the slab. The refractive index is

Diodes and identifying components

The last three experiments are about semiconductor devices (Section 19.1 and Section 19.2). Two plot characteristic curves; the third uses the same one-way behaviour to sort a mixed collection of components.

📐 Result 20.16 — Reading diode characteristics
  • Forward bias (p side positive): almost no current until the knee (cut-in) voltage — about $0.7\ \text{V}$ for silicon, $0.3\ \text{V}$ for germanium, $1.6$–$2\ \text{V}$ for a red LED — then a steep rise (milliamperes). The dynamic resistance at a point is $r_d=\dfrac{\Delta V}{\Delta I}$ (inverse slope of the $I$–$V$ curve there).
  • Reverse bias: a tiny, nearly constant reverse saturation current (microamperes or less) until breakdown.
  • Zener diode, reverse bias: at the breakdown voltage $V_Z$ the reverse current rises sharply while the voltage stays almost constant at $V_Z$; a series resistor $R=\dfrac{V_s-V_Z}{I}$ limits the current.

Experiment 7 — Characteristic curves of a p–n junction diode

Aim. To draw the $I$–$V$ characteristic curves of a p–n junction diode in forward and reverse bias. Apparatus. Diode, $3\ \text{V}$ and $15\ \text{V}$ batteries (or a variable supply), rheostat (as potential divider), milliammeter, microammeter, voltmeters ($0$–$3\ \text{V}$ and $0$–$15\ \text{V}$), key.

Method.

  1. Forward bias: connect the battery through the potential divider so that the p side is positive; the milliammeter in series and the low-range voltmeter across the diode. Increase $V$ from $0$ in steps of $0.1\ \text{V}$ (smaller steps near the knee) and record $I$ in mA.
  2. Reverse bias: reverse the diode connections, change to the higher-voltage battery, the microammeter and the high-range voltmeter. Increase the reverse voltage in steps of $1\ \text{V}$ and record $I$ in $\mu\text{A}$ (stay well below the breakdown rating).
  3. Plot both on one graph, with different current scales for the two quadrants.
Forward $V$ (V)$0.0$$0.50$$0.60$$0.65$$0.70$$0.75$
$I$ (mA)$0$$0.1$$1.0$$3.0$$8.0$$18.0$
Reverse $V$ (V)$0$$-2$$-5$$-10$
$I$ ($\mu$A)$0$$-0.8$$-1.0$$-1.0$

Precautions and sources of error. Always include a series resistance (or start from zero with the divider) — a forward-biased diode connected straight across a battery draws a destructive current; do not exceed the maximum forward current or the reverse breakdown voltage; use a milliammeter for forward and a microammeter for reverse readings; take close readings near the knee. The diode warms at high forward current and its curve shifts.

Experiment 8 — Characteristic curve of a Zener diode and its breakdown voltage

Aim. To draw the reverse characteristic of a Zener diode and find its reverse breakdown voltage. Apparatus. Zener diode (e.g. $5.1\ \text{V}$), variable dc supply ($0$–$15\ \text{V}$), series protective resistor (a few hundred ohms), rheostat, voltmeter, milliammeter, key.

Method.

  1. Connect the supply, rheostat, protective resistor and milliammeter in series with the Zener in reverse bias; voltmeter across the Zener.
  2. Raise the supply slowly; record the voltage across the Zener and the current. The current stays nearly zero, then rises steeply at $V_Z$ while the voltage hardly changes.
  3. Plot $I$ against $V$ (reverse quadrant). $V_Z$ is where the curve turns sharply downward (the voltage at which the current begins to rise steeply).
Reverse voltage across Zener (V)$2.0$$4.0$$5.0$$5.1$$5.2$
Reverse current (mA)$0$$0.01$$0.5$$10$$20$

Precautions and sources of error. Never omit the protective series resistor; increase the voltage slowly near breakdown; do not exceed the Zener's power rating ($V_ZI$). The breakdown "knee" is not perfectly sharp, so $V_Z$ is read where the curve becomes steep.

Experiment 9 — Identifying a diode, an LED, a resistor and a capacitor

Aim. To identify a diode, an LED, a resistor and a capacitor from a mixed collection of such items. Apparatus. The components, a multimeter (resistance range), or a battery with a bulb or series resistor and an indicator LED.

📐 Result 20.17 — Identification tests

Connect each two-lead item to the ohmmeter (or the battery–indicator circuit) one way, then with the leads reversed:

Itemone wayreversedother sign
resistorsteady finite resistancethe same valueno light, no change with time
diodelow resistance (conducts)very high resistancedoes not glow
LEDconductsvery high resistanceglows when it conducts
capacitora brief kick, then very high resistancethe same brief kick, then very highcharging current that dies away

An item with three or more leads (a transistor) is set aside; it is not among these four.

Method and precautions. Test each item in both directions with the same meter range; watch the meter at the moment of connection (the capacitor's kick lasts only an instant for a small capacitor — use a high resistance range); discharge capacitors by touching their leads together before testing; keep the test current small so the LED and diode are not damaged.

✏️ Example 6 — Reading diode and Zener characteristics
Use the tables of Experiments 7 and 8. (a) Estimate the knee voltage of the diode and find its dynamic resistance between $0.70\ \text{V}$ and $0.75\ \text{V}$, and its static resistance $V/I$ at $0.75\ \text{V}$. (b) Find the reverse resistance at $-10\ \text{V}$. (c) Read the Zener's breakdown voltage and its dynamic resistance in breakdown. (d) This Zener is to be run at $15\ \text{mA}$ from a $9.0\ \text{V}$ supply. Find the series resistance needed and the power dissipated in the Zener.
Find the dynamic resistance in (a) first:
(a) The current becomes appreciable near $0.6$–$0.65\ \text{V}$: knee $\approx0.65\ \text{V}$ (silicon). $r_d=\dfrac{0.05}{10.0\times10^{-3}}=5.0\ \Omega$; static resistance $\dfrac{0.75}{18.0\times10^{-3}}=42\ \Omega$ — the two are quite different for a non-ohmic device.
(b) $\dfrac{10}{1.0\times10^{-6}}=1.0\times10^7\ \Omega$: in reverse bias the diode is almost an open switch.
(c) The current rises sharply at about $5.1\ \text{V}$: $V_Z\approx5.1\ \text{V}$. In breakdown, $r_Z=\dfrac{5.2-5.1}{(20-10)\times10^{-3}}=10\ \Omega$ — small, so the voltage stays nearly constant.
(d) $R=\dfrac{9.0-5.1}{0.015}=260\ \Omega$; power $5.1\times0.015=0.077\ \text{W}$.
⏱ Shortcut Dynamic resistance is always "change over change"; static resistance is "value over value". JEE options often include both.

In Interactive 2 choose the Zener diode (5.1 V), set the supply to $-9.0\ \text{V}$ and the series resistance to $500\ \Omega$. What do you expect for the voltage across the Zener and the current?

The readouts show $V_D=-5.18\ \text{V}$, $I=-7.65\ \text{mA}$ and "reverse — breakdown": the operating point is where the load line $I=(V_s-V)/R$ crosses the steep breakdown part of the curve. Roughly $(9.0-5.1)/500=7.8\ \text{mA}$; the Zener's small resistance ($10\ \Omega$ in this model) lifts $|V|$ a little above $5.1\ \text{V}$. An ordinary diode would block (switch to the silicon diode: the current drops to nanoamperes); $-18\ \text{mA}$ forgets the resistor's share of the voltage.
Interactive 2 — Diode Characteristic Tracer

A device is connected in series with a resistance $R$ to a supply $V_s$ (the circuit is in the corner). The black curve is its $I$–$V$ characteristic; the dashed load line $I=(V_s-V)/R$ crosses it at the operating point. Choose the device, set $V_s$ and $R$, or press Play to sweep the supply like a curve tracer — the dots record the points you would plot in the experiment.

2.0 V100 Ω
voltage across device—
current—
power in device—
state—
⚠️ JEE Main traps

1. Metre bridge. $X=R(100-l)/l$ with $l$ measured from the end where $R$ is connected. After interchanging, the null point is measured from the same end: $X=Rl_2/(100-l_2)$. The null point should be near the middle.

2. Half deflection. $R$ is kept fixed while the shunt is adjusted; $G=RS/(R-S)$, which is $\approx S$ only because $R\gg S$. The figure of merit uses the deflection without the shunt.

3. Signs on the optical bench. Concave mirror: $f=uv/(u+v)$ with $u,v\lt0$ for real images; convex lens: $f=uv/(u-v)$ with $u\lt0$, $v\gt0$. Using the mirror formula for a lens is the commonest slip.

4. Convex mirror. It cannot be studied alone by the u–v method (its images of real objects are virtual). With the auxiliary lens, $R=$ mirror-to-image distance, $f=R/2$.

5. Diodes. Forward current in mA, reverse in $\mu$A — the two halves of the graph have different scales. Dynamic resistance $\Delta V/\Delta I$ is not $V/I$. A Zener is used in reverse bias and always with a series resistor.

A component tested with a multimeter on a resistance range shows a low resistance one way and a very high resistance when the leads are reversed, and does not glow. It is

Exercises

Use the Cartesian sign convention for mirrors and lenses (distances from the pole or optical centre, positive along the incident light). Take the cells as having negligible internal resistance unless told otherwise.

I
Metre bridge, Ohm's law and the galvanometer.
  • 1 With $R=4.0\ \Omega$ in the left gap of a metre bridge, the null point is at $44.0\ \text{cm}$ from the left end. Find the resistance in the right gap.
  • 2 The resistance of part 1 is a wire $1.00\ \text{m}$ long and $0.50\ \text{mm}$ in diameter. Find the resistivity of its material.
  • 3 With $R=10\ \Omega$ on the left, the null point is at $33.0\ \text{cm}$; after interchanging, it is at $67.4\ \text{cm}$ (both from the left end). Find the mean value of $X$ and $\beta-\alpha$.
  • 4 Why should the null point lie near the middle of the wire, and why must the jockey not be slid along the wire?
  • 5 Use the $V$–$I$ table of Experiment 2 to find the resistance of the wire. If the wire is $0.50\ \text{m}$ long with diameter $0.32\ \text{mm}$, find its resistivity.
  • 6 A voltmeter of resistance $500\ \Omega$ is connected across a $10.0\ \Omega$ resistor in the Ohm's-law circuit. What resistance will $V/I$ give, and what is the percentage error?
  • 7 In the half-deflection method, $R=8000\ \Omega$ gives $25$ divisions with a $1.5\ \text{V}$ cell, and a shunt of $80\ \Omega$ halves the deflection. Find $G$ and the figure of merit.
  • 8 Why must $R$ be very large compared with $S$ in the half-deflection method?
  • 9 A galvanometer of resistance $80\ \Omega$, figure of merit $2.0\times10^{-5}\ \text{A/div}$ and $30$ divisions is to be made into a voltmeter of range $0$–$3.0\ \text{V}$. Find the series resistance.
1 $X=4.0\times\dfrac{56.0}{44.0}=5.09\ \Omega$.
2 $\rho=\dfrac{\pi d^2X}{4L}=\dfrac{\pi(5.0\times10^{-4})^2\times5.09}{4\times1.00}=1.0\times10^{-6}\ \Omega\,\text{m}$ (nichrome-like).
3 $X_1=10\times\dfrac{67.0}{33.0}=20.3\ \Omega$; $X_2=10\times\dfrac{67.4}{32.6}=20.7\ \Omega$; mean $20.5\ \Omega$. $l_1+l_2=100.4$, so $\beta-\alpha=0.4\ \text{cm}$.
4 The fractional error $\dfrac{100\,\Delta l}{l(100-l)}$ is least at $l=50\ \text{cm}$, and end errors matter least there. Sliding scrapes the wire, making it non-uniform, so the "resistance proportional to length" assumption fails.
5 Slope $=\dfrac{2.08-0.52}{0.30}=5.2\ \Omega$. $\rho=\dfrac{RA}{L}=\dfrac{5.2\times\pi(1.6\times10^{-4})^2}{0.50}=8.4\times10^{-7}\ \Omega\,\text{m}$.
6 $\dfrac{10.0\times500}{510}=9.80\ \Omega$: $2.0\%$ too low.
7 $G=\dfrac{8000\times80}{7920}=80.8\ \Omega$; $k=\dfrac{1.5}{(8080.8)\times25}=7.4\times10^{-6}\ \text{A/div}$.
8 So that connecting the shunt leaves the circuit current practically unchanged; only then does halving the galvanometer's share mean $S\approx G$ (and the exact formula's correction stays small).
9 $I_g=30\times2.0\times10^{-5}=6.0\times10^{-4}\ \text{A}$; $R=\dfrac{3.0}{6.0\times10^{-4}}-80=4920\ \Omega$.
II
Mirrors and lenses on the optical bench.
  • 1 For a concave mirror $u=-36.0\ \text{cm}$ and $v=-45.0\ \text{cm}$. Find the focal length.
  • 2 For a convex lens $u=-24.0\ \text{cm}$ and $v=+40.0\ \text{cm}$. Find the focal length.
  • 3 For a convex lens, the $|u|$–$|v|$ graph meets the line $|v|=|u|$ at $30\ \text{cm}$. Find the focal length.
  • 4 The graph of $1/v$ against $1/u$ for a convex lens has $1/v$-intercept $0.050\ \text{cm}^{-1}$. Find $f$ and the slope of the line.
  • 5 A convex lens forms a real image $36.0\ \text{cm}$ from it. A convex mirror placed $22.0\ \text{cm}$ from the lens, facing it, sends the light back along its path. Find the focal length of the mirror.
  • 6 For a concave mirror the bench gives $u=-30.0\ \text{cm}$ and $v=-60.0\ \text{cm}$, but the index rod shows that every observed distance is $0.2\ \text{cm}$ too small. Find the corrected focal length.
  • 7 Explain why the tips of the pin and the image (rather than any other parts) are used to remove parallax, and why readings very close to the focus are avoided.
  • 8 A convex lens of focal length $15\ \text{cm}$ is used. What is the least distance between the object pin and the real image pin?
1 $f=\dfrac{uv}{u+v}=\dfrac{1620}{-81.0}=-20.0\ \text{cm}$.
2 $f=\dfrac{uv}{u-v}=\dfrac{-960}{-64.0}=+15.0\ \text{cm}$.
3 The meeting point is $(2f,2f)$: $f=15\ \text{cm}$.
4 $\tfrac1v=\tfrac1u+\tfrac1f$: intercept $1/f=0.050\ \text{cm}^{-1}$, $f=20\ \text{cm}$; slope $+1$.
5 $R=36.0-22.0=14.0\ \text{cm}$, $f=+7.0\ \text{cm}$.
6 Corrected $u=-30.2$, $v=-60.2\ \text{cm}$: $f=\dfrac{(30.2)(60.2)}{-90.4}=-20.1\ \text{cm}$.
7 The tips are where the pin and its image can be made to touch; aligning them tip to tip makes the test sensitive and avoids comparing different heights. Near $F$, $v$ becomes very large and a tiny error in $u$ changes $v$ enormously, so those readings are unreliable.
8 $|u|+|v|$ is least, $4f=60\ \text{cm}$, when $|u|=|v|=2f$.
III
The prism and the glass slab.
  • 1 An equilateral prism gives a minimum deviation of $38^\circ$. Find its refractive index.
  • 2 In the $i$–$\delta$ experiment with $A=60^\circ$, a ray incident at $40^\circ$ emerges at $58.5^\circ$. Find the deviation.
  • 3 At what angle of incidence does minimum deviation occur for the prism of part 1?
  • 4 Explain why every deviation above the minimum is produced by two angles of incidence, and why the curve is not symmetric about its minimum.
  • 5 A travelling microscope reads $4.215\ \text{cm}$ on a mark, $4.795\ \text{cm}$ on the mark seen through a slab and $5.955\ \text{cm}$ on the top of the slab. Find the refractive index.
  • 6 A mark is viewed through a glass slab $3.00\ \text{cm}$ thick ($n=1.50$). By how much must the travelling microscope be raised, from its focus on the mark without the slab, to refocus on the mark?
  • 7 Why is lycopodium powder sprinkled on the top of the slab, and why is a thick slab better than a thin one?
1 $n=\dfrac{\sin49^\circ}{\sin30^\circ}=2\times0.755=1.51$.
2 $\delta=i+e-A=40+58.5-60=38.5^\circ$.
3 $i=\tfrac12(A+\delta_m)=49^\circ$.
4 Light paths are reversible: a ray entering at $e$ leaves at $i$ with the same deviation, so $i$ and $e$ give the same $\delta$; only at the minimum do they coincide. Below $i_\text{min}$ the deviation rises steeply (towards grazing emergence), above it more slowly, so the curve is lopsided.
5 Real $1.740\ \text{cm}$, apparent $1.160\ \text{cm}$: $n=1.50$.
6 Normal shift $t(1-1/n)=3.00\times\tfrac13=1.00\ \text{cm}$.
7 A clean glass surface gives nothing to focus on; the fine powder marks it. The apparent thickness is the difference of two readings, each uncertain by about the depth of focus; a thicker slab makes that uncertainty a smaller fraction.
IV
Diodes and identifying components.
  • 1 A diode carries $10\ \text{mA}$ at $0.70\ \text{V}$ and $18\ \text{mA}$ at $0.74\ \text{V}$. Find its dynamic resistance in this range.
  • 2 Find the static resistance of the diode of part 1 at $0.74\ \text{V}$.
  • 3 A silicon diode passes $0.50\ \mu\text{A}$ at a reverse voltage of $10\ \text{V}$. Find its reverse resistance.
  • 4 A $6.2\ \text{V}$ Zener is to carry $20\ \text{mA}$ from a $12\ \text{V}$ supply. Find the series resistance needed.
  • 5 Find the power dissipated in the Zener of part 4.
  • 6 In Experiment 7, why is a milliammeter used for forward bias but a microammeter for reverse bias, and why is a higher-voltage battery used for reverse bias?
  • 7 Four unlabelled two-lead items give these multimeter results — P: $1.2\ \text{k}\Omega$ both ways; Q: low one way, very high the other, glows; R: a brief kick both ways, then very high; S: low one way, very high the other, no glow. Identify them.
  • 8 Why does a red LED need about $1.8\ \text{V}$ to conduct while a silicon diode needs only about $0.7\ \text{V}$?
1 $r_d=\dfrac{0.04}{8\times10^{-3}}=5.0\ \Omega$.
2 $\dfrac{0.74}{18\times10^{-3}}=41.1\ \Omega$.
3 $\dfrac{10}{0.50\times10^{-6}}=2.0\times10^7\ \Omega$.
4 $R=\dfrac{12-6.2}{0.020}=290\ \Omega$.
5 $P=6.2\times0.020=0.124\ \text{W}$.
6 Forward currents are milliamperes once past the knee, at well under $1\ \text{V}$; reverse currents are microamperes or less and change little, so they need a sensitive meter and larger voltages to show the (flat) reverse curve.
7 P: resistor; Q: LED; R: capacitor; S: diode.
8 The LED's semiconductor has a larger band gap (that is why it emits visible light), so a larger forward voltage is needed before the junction conducts appreciably.
🎯 Exam corner JEE Main · MCQJEE Main · Numerical

E1. JEE Main · Numerical In the half-deflection method, a galvanometer in series with a resistance of $9900\ \Omega$ and a cell of negligible internal resistance shows a deflection of $40$ divisions. Keeping the series resistance fixed, a shunt of $99\ \Omega$ across the galvanometer reduces the deflection to $20$ divisions. Find the resistance of the galvanometer in ohms. Give the answer to the nearest integer.

Formula $G=\dfrac{RS}{R-S}=\dfrac{9900\times99}{9801}$.
Arithmetic $9801=99^2$ and $9900=99\times100$, so $G=\dfrac{99\times100\times99}{99^2}=100\ \Omega$.
Answer $100$.
⏱ Shortcut Taking $G\approx S$ gives $99$ — close, but the integer answer needs the exact formula here.

E2. JEE Main · MCQ In the u–v experiment with a convex lens, a graph of $1/v$ ($y$-axis) against $1/u$ ($x$-axis) is drawn using the Cartesian sign convention. It is a straight line with (A) slope $-1$ and $y$-intercept $1/f$ (B) slope $+1$ and $y$-intercept $1/f$ (C) slope $+1$ and $y$-intercept $-1/f$ (D) slope $-1$ passing through the origin

Formula $\dfrac1v-\dfrac1u=\dfrac1f$, i.e. $\dfrac1v=(+1)\dfrac1u+\dfrac1f$.
Read off $y=mx+c$ with $m=+1$, $c=1/f$ (positive for a convex lens).
Answer (B).
⏱ Shortcut (A) is the mirror ($\tfrac1v=-\tfrac1u+\tfrac1f$). In magnitudes, both give slope $-1$ — always check which convention a question uses.

E3. JEE Main · Numerical A convex lens forms a real image of an object pin at a distance of $40\ \text{cm}$ from the lens. A convex mirror is placed between the lens and this image, facing the lens, and moved until the final image coincides with the object pin. The mirror is then $16\ \text{cm}$ from the lens. Find the focal length of the convex mirror in cm. Give the answer to the nearest integer.

Idea The light retraces its path, so it falls normally on the mirror: the lens's image point is the mirror's centre of curvature.
Radius $R=40-16=24\ \text{cm}$, $f=R/2=12\ \text{cm}$.
Answer $12$.
⏱ Shortcut $24$ (forgetting to halve) and $8$ (halving $16$) are the traps.

E4. JEE Main · MCQ A travelling microscope focused on a scratch on a table reads $2.548\ \text{cm}$. A glass slab is placed over the scratch, and the microscope must be raised to $2.802\ \text{cm}$ to see the scratch again; focused on the top of the slab it reads $3.310\ \text{cm}$. The refractive index of the glass is (A) $1.33$ (B) $1.62$ (C) $1.50$ (D) $2.00$

Thicknesses Real $3.310-2.548=0.762\ \text{cm}$; apparent $3.310-2.802=0.508\ \text{cm}$.
Index $n=\dfrac{0.762}{0.508}=1.50$.
Answer (C).
⏱ Shortcut Normal shift $0.254$ is exactly one third of $0.762$, and $1-\tfrac1n=\tfrac13$ gives $n=1.5$ at once.

E5. JEE Main · Numerical In an experiment to plot the $i$–$\delta$ curve of an equilateral glass prism, the deviation is found to be least when the angle of incidence is $48^\circ$. If the refractive index of the glass is $n$, find $100n$ to the nearest integer. (Take $\sin48^\circ=0.743$.)

Minimum At minimum deviation $i=e$ and $r=A/2=30^\circ$ (so $\delta_m=2i-A=36^\circ$).
Snell $n=\dfrac{\sin48^\circ}{\sin30^\circ}=\dfrac{0.743}{0.5}=1.486$, so $100n=148.6$.
Answer $149$.
⏱ Shortcut No need for $\delta_m$: $n=\sin i_\text{min}/\sin(A/2)$ directly.

E6. JEE Main · MCQ Four components are tested with a multimeter on a resistance range, each first one way and then with the leads reversed. Which observation is correctly matched? (A) resistor — low resistance one way, very high the other (B) LED — the same resistance both ways, with a glow (C) diode — a brief kick both ways, then very high resistance (D) capacitor — a brief kick both ways, then very high resistance

Tests Resistor: same value both ways. Diode: conducts one way only, no light. LED: conducts one way only and glows. Capacitor: charging kick in either direction, then no current.
Match (A), (B) and (C) each describe a different component's behaviour; only (D) is correctly matched.
Answer (D).
⏱ Shortcut "One-way" means diode or LED (light decides); "both ways, steady" is a resistor; "both ways, transient" is a capacitor.
🔬 Research–Teaching NexusResearch-tutored · optional, about 60 minutes

Research question. Can the forward characteristic of an LED be used to estimate the energy of the photons it emits — and hence Planck's constant — with only a battery, a resistor and a multimeter?

Why it matters. LEDs now light homes, streets and screens worldwide, and their efficiency depends on how closely the electrical energy per electron matches the photon energy. Engineers choose LED materials by their band gaps; the knee voltage you read off an $I$–$V$ curve is a direct, cheap measurement of that gap. The same idea is used in teaching laboratories around the world as a low-cost estimate of $h$.

What to do.

  1. Take LEDs of three or four colours (infrared, red, yellow, green, blue if available) with known peak wavelengths from their data sheets.
  2. For each, connect a $1.5$–$6\ \text{V}$ supply through a $1\ \text{k}\Omega$ resistor and a potentiometer; measure the voltage across the LED and the current (with the multimeter's mA range) in small steps from zero up to about $10\ \text{mA}$.
  3. Plot each forward characteristic and find the knee voltage $V_k$ by extending the straight, steep part of the curve back to the voltage axis.
  4. Plot $V_k$ against $1/\lambda$. If $eV_k\approx hc/\lambda$, the slope is $hc/e$; find $h$.
  5. Compare with the accepted value and discuss why the agreement is only rough.

Tools: Assorted LEDs with data sheets, battery or variable supply, $1\ \text{k}\Omega$ resistor, potentiometer, two multimeters (or one used in turn), graph paper or a spreadsheet.

Hand in: The $I$–$V$ curves on one set of axes, a table of $\lambda$ and $V_k$, the $V_k$–$1/\lambda$ graph with its slope, your value of $h$ with an uncertainty, and a short discussion of the sources of error.

Going further. Cool an LED (in a sealed bag in ice water) and warm it gently; how does its knee voltage change with temperature, and what does that say about using it as a thermometer?

Instructor note: values of $h$ within $10$–$20\%$ are typical; the knee depends on how it is defined and on the series resistance inside the LED, and blue and white LEDs often depart from the line. Remind students never to connect an LED to a supply without a series resistor.

🧪 Self-check quiz

0/5 correct

Q1. In a metre-bridge experiment, the known resistance is chosen so that the null point lies near the middle of the wire because

Q2. In the half-deflection method the galvanometer resistance is approximately equal to the shunt resistance because

Q3. The focal length of a convex mirror is found using an auxiliary convex lens because

Q4. At the minimum of the $i$–$\delta$ curve of a prism,

Q5. To find the breakdown voltage of a Zener diode, it is connected