Chapter 8 · Introduction

Chapter 8 — Thermodynamics

Thermodynamics keeps the accounts of energy. The zeroth law defines temperature, the first law $Q=\Delta U+W$ balances heat, work and internal energy in every process of a gas, and the second law decides which way energy is willing to flow — and caps every engine at the Carnot efficiency $1-T_2/T_1$.

A diesel engine has no spark plug. It squeezes air so quickly to about a twentieth of its volume that the air becomes hot enough — several hundred degrees Celsius — to ignite the fuel sprayed into it. A bicycle pump grows warm after a few hard strokes for the same reason. A refrigerator does the opposite trick, pushing heat out of a cold box into a warmer kitchen, but only while it is plugged in. And every thermal power station, however modern, throws away more energy as warm water and exhaust than it delivers as electricity. Why can heat not be turned completely into work? Why does compressing a gas quickly heat it while compressing it slowly need not? How good can an engine possibly be?

Thermodynamics answers these questions without looking at a single molecule, using a few state variables — pressure, volume, temperature, internal energy — and three laws. The zeroth law gives temperature its meaning. The first law, $Q=\Delta U+W$, is the conservation of energy with heat included: the heat put into a system goes partly into its internal energy and partly into the work it does, and that work is the area under its path on a $p$–$V$ diagram. Applied to an ideal gas it gives the four standard processes — isochoric, isobaric, isothermal and adiabatic — and the cycles built from them. The second law then says which processes can actually happen, separates reversible from irreversible ones, and sets the ceiling every engine must live under, the Carnot efficiency $\eta=1-\dfrac{T_2}{T_1}$.

Thermal equilibrium→Zeroth law & temperature→Heat, work, internal energy→$W=\displaystyle\int p\,dV$→First law $Q=\Delta U+W$→Four standard processes→Adiabatic $pV^\gamma=\text{const}$→Cycles→Second law & reversibility→Carnot $\eta=1-\tfrac{T_2}{T_1}$
🎯 By the end of this chapter you can…
  • explain thermal equilibrium, state the zeroth law, and use it to define temperature, including readings of a constant-volume gas thermometer;
  • distinguish heat, work and internal energy, treat internal energy as a state variable, and use $\Delta U=nC_V\Delta T$ for an ideal gas in any process;
  • calculate the work done by a gas as the area under its $p$–$V$ path — at constant pressure, along straight lines and power-law curves — and recognise free expansion, where $W=0$;
  • apply the first law with consistent signs to heating, boiling, and gases pushing pistons against the atmosphere and springs;
  • find $W$, $Q$ and $\Delta U$ for isochoric, isobaric, isothermal and adiabatic processes, using $C_p-C_V=R$, $\gamma=\dfrac{C_p}{C_V}$, $pV^\gamma=\text{const}$ and $TV^{\gamma-1}=\text{const}$;
  • work round a cyclic process leg by leg, reading the net work as the enclosed area with its sign set by the direction;
  • state the second law in its Kelvin–Planck and Clausius forms, tell reversible from irreversible processes, and test claims for impossible machines;
  • use the efficiency of a heat engine, the coefficient of performance of a refrigerator or heat pump, and their Carnot limits, and solve mixed JEE Main problems on the whole chapter.

In the teaser below, air ($\gamma=1.4$) in a pump at $300\ \text{K}$ and $100\ \text{kPa}$ is squeezed to one quarter of its volume so quickly that no heat has time to leave. What is its temperature just afterwards?

Set the compression ratio to $4.0$: the "fast push (adiabatic)" readout shows $T_2=522\ \text{K}$ and $p_2=696\ \text{kPa}$, and the work done on the gas is $185\ \text{J}$. With $Q=0$ the first law gives $\Delta U=-W_\text{by gas}=+185\ \text{J}$: all the work stays in the gas as internal energy, so it heats up even though no heat was supplied. Quantitatively $TV^{\gamma-1}=\text{const}$ gives $T_2=300\times4^{0.4}=522\ \text{K}$. The slow push (isothermal) stays at $300\ \text{K}$ and $400\ \text{kPa}$ because the $139\ \text{J}$ of work leaks out as heat. $1200\ \text{K}$ assumes $T\propto1/V$, which holds for neither process (at constant pressure the gas would actually cool, to $75\ \text{K}$), and $2090\ \text{K}$ uses $4^{1.4}$, which is the pressure ratio.
Teaser — Pump It: Slowly or Quickly?

$1.0\ \text{L}$ of air ($\gamma=1.4$) at $100\ \text{kPa}$ and $300\ \text{K}$ is compressed to $1/r$ of its volume in two ways: slowly, so heat leaks out and the temperature stays at $300\ \text{K}$ (isothermal), or quickly, with no time for heat to leave (adiabatic). Choose the compression ratio $r$; the shaded areas are the work done on the gas.

4.0
slow push (isothermal): final state—
work on gas = heat given out—
fast push (adiabatic): final state—
work on gas = rise in U—

Sections in this chapter

🎯 Chapter mixed test JEE Main · MCQJEE Main · Numerical

Eight original problems that move between the three sections in no fixed order, as the real paper does; several need two sections at once. Each has a pace timer of $2.4$ minutes — the time per Physics question in JEE Main — and the ⏱ Take as a timed test button runs all eight as one sitting ($8\times2.4\approx19$ minutes) with the NTA question palette and $+4/-1$ marking. Throughout, $Q$ is heat given to the gas and $W$ is work done by it.

E1. JEE Main · MCQ In a certain process a gas absorbs $500\ \text{J}$ of heat while its surroundings do $200\ \text{J}$ of work on it. The change in its internal energy is (A) $300\ \text{J}$ (B) $700\ \text{J}$ (C) $-300\ \text{J}$ (D) $-700\ \text{J}$

Signs $Q=+500\ \text{J}$ (absorbed); work done on the gas means $W=-200\ \text{J}$ (Section 8.1).
First law $\Delta U=Q-W=500-(-200)=700\ \text{J}$.
Answer (B).
⏱ Shortcut Both heat in and work in add energy to the gas, so the two numbers simply add. (A) treats work done on the gas as work done by it.

E2. JEE Main · Numerical A Carnot engine works between a source at $500\ \text{K}$ and a sink at $300\ \text{K}$. Its working substance is $2.0\ \text{mol}$ of an ideal gas, whose volume doubles during the isothermal expansion. Taking $R=8.31\ \text{J mol}^{-1}\text{K}^{-1}$ and $\ln2=0.693$, find the work done by the engine per cycle, in joules. Give the answer to the nearest integer.

Heat in On the isothermal expansion at $T_1$, $\Delta U=0$ and $Q_1=W=nRT_1\ln\dfrac{V_2}{V_1}=2.0\times8.31\times500\times0.693=5759\ \text{J}$ (Section 8.2).
Efficiency $\eta_\text{C}=1-\dfrac{300}{500}=0.40$ (Section 8.3), so $W=0.40\times5759=2303.5\ \text{J}$.
Answer $2304$.
⏱ Shortcut For a Carnot cycle $W=nR(T_1-T_2)\ln\dfrac{V_2}{V_1}=2.0\times8.31\times200\times0.693=2303.5\ \text{J}$. Entering $5759$ (the heat taken in) forgets the heat rejected to the sink.

E3. JEE Main · MCQ Three equal samples of an ideal gas ($\gamma=1.4$) start from the same state, and each expands quasi-statically to twice its volume: one at constant pressure, one isothermally and one adiabatically. The works done, $W_p$, $W_T$ and $W_\text{ad}$, satisfy (A) $W_T\gt W_p\gt W_\text{ad}$ (B) $W_\text{ad}\gt W_T\gt W_p$ (C) $W_p\gt W_T\gt W_\text{ad}$ (D) $W_p=W_T\gt W_\text{ad}$

Picture From the common starting point on the $p$–$V$ diagram the isobar runs flat, the isotherm falls, and the adiabat falls $\gamma$ times more steeply (Section 8.2). Work is the area under each path (Section 8.1).
Numbers In units of $p_0V_0$: $W_p=1$, $W_T=\ln2=0.693$, $W_\text{ad}=\dfrac{1-2^{-0.4}}{0.4}=0.605$.
Answer (C).
⏱ Shortcut The higher the curve, the bigger the area: flat beats falling beats falling faster. No calculation needed.

E4. JEE Main · Numerical An ideal gas is taken round a cycle $A\to B\to C\to A$. From $A$ to $B$ its volume is constant and it absorbs $600\ \text{J}$ of heat. From $B$ to $C$ it expands adiabatically, doing $450\ \text{J}$ of work. From $C$ back to $A$ it is compressed, $250\ \text{J}$ of work being done on it. Find the heat rejected by the gas during $C\to A$, in joules. Give the answer to the nearest integer.

Whole cycle The gas returns to $A$, so $\Delta U_\text{cycle}=0$ and $Q_\text{net}=W_\text{net}$ (Sections 8.1 and 8.2).
Net work $W_{AB}=0$ (constant volume), $W_{BC}=+450\ \text{J}$, $W_{CA}=-250\ \text{J}$: $W_\text{net}=200\ \text{J}$.
Heat $Q_{AB}+Q_{BC}+Q_{CA}=200$ with $Q_{BC}=0$: $Q_{CA}=200-600=-400\ \text{J}$. Check leg by leg: $\Delta U_{AB}=+600$, $\Delta U_{BC}=-450$, so $\Delta U_{CA}=-150\ \text{J}$ and $Q_{CA}=-150+(-250)=-400\ \text{J}$ ✓.
Answer $400$.
⏱ Shortcut Net heat in $=$ net work out $=450-250$; whatever of the $600\ \text{J}$ is not turned into net work must leave on the last leg.

E5. JEE Main · MCQ Which of the following is consistent with the first law of thermodynamics but forbidden by the second? (A) An ideal gas expanding isothermally, absorbing heat $Q$ and doing work $Q$ (B) Heat flowing by itself from a hot body to a cold one (C) A refrigerator that uses electrical work to move heat from its cold interior to a warmer room (D) A ship's engine that, working in a cycle, takes heat from the sea water and converts all of it into work

Check each (A) converts heat fully into work, but in a single process, not a cycle — the gas ends in a different state, so it is allowed. (B) is the natural direction of heat flow. (C) is allowed because work is supplied.
Kelvin–Planck (D) is a cyclic device that takes heat from one reservoir and turns all of it into work. Energy is conserved, but no engine can do this (Section 8.3).
Answer (D).
⏱ Shortcut The second law forbids complete conversion of heat into work only in a cycle; look for the words "in a cycle" and "all of it".

E6. JEE Main · Numerical One mole of a diatomic ideal gas expands adiabatically and quasi-statically, and its temperature falls from $400\ \text{K}$ to $300\ \text{K}$. Taking $R=8.3\ \text{J mol}^{-1}\text{K}^{-1}$, find the work done by the gas, in joules. Give the answer to the nearest integer.

First law Adiabatic: $Q=0$, so $W=-\Delta U$ (Section 8.1), and $\Delta U=nC_V\Delta T$ for an ideal gas in any process.
Number Diatomic $C_V=\tfrac52R$ (Section 8.2): $W=nC_V(T_1-T_2)=1\times\tfrac52\times8.3\times100=2075\ \text{J}$.
Answer $2075$.
⏱ Shortcut $W=\dfrac{nR(T_1-T_2)}{\gamma-1}=\dfrac{830}{0.4}=2075\ \text{J}$. Using $C_p$ instead of $C_V$ gives $2905$.

E7. JEE Main · MCQ A Carnot engine absorbs $1200\ \text{J}$ of heat per cycle from a source at $600\ \text{K}$ and rejects $800\ \text{J}$ to its sink. The temperature of the sink is (A) $400\ \text{K}$ (B) $300\ \text{K}$ (C) $200\ \text{K}$ (D) $450\ \text{K}$

Carnot For a reversible engine $\dfrac{Q_2}{Q_1}=\dfrac{T_2}{T_1}$ (Section 8.3).
Number $T_2=600\times\dfrac{800}{1200}=400\ \text{K}$; the efficiency is $\tfrac13$.
Answer (A).
⏱ Shortcut (C) uses the work $400\ \text{J}$ in place of $Q_2$: $600\times\tfrac{400}{1200}=200$.

E8. JEE Main · Numerical A gas is held in a vertical cylinder by a smooth piston of mass $10\ \text{kg}$ and area $0.010\ \text{m}^2$; the atmospheric pressure outside is $1.0\times10^5\ \text{Pa}$. The gas is heated slowly, absorbs $300\ \text{J}$ of heat, and the piston rises $8.0\ \text{cm}$. Taking $g=10\ \text{m/s}^2$, find the increase in the internal energy of the gas, in joules. Give the answer to the nearest integer.

Pressure The piston moves slowly, so it is in equilibrium: $p=p_0+\dfrac{mg}{A}=1.0\times10^5+\dfrac{100}{0.010}=1.1\times10^5\ \text{Pa}$, constant.
Work $W=p\,\Delta V=1.1\times10^5\times0.010\times0.080=88\ \text{J}$.
First law $\Delta U=Q-W=300-88=212\ \text{J}$ (Section 8.1).
Answer $212$.
⏱ Shortcut The gas does work against the air (80 J) and lifts the piston (8 J). Forgetting the piston's weight gives $220$.
✅ Before you start
You need the ideas of heat and temperature, temperature scales, specific heat capacity and latent heat from Section 7.5, and pressure as force per unit area from Section 7.2. Work done by a gas is the work of a variable force read as the area under a graph (Section 4.1, Section 2.1), and the first law is the conservation of energy of Section 4.2 with heat added to the account. The chapter uses the ideal gas equation $pV=nRT$ as a given rule (it is explained from molecular motion in Section 9.1; you may know it from Class 11 Chemistry). From mathematics, recall natural logarithms and that $\displaystyle\int\frac{dV}{V}=\ln V$.