Chapter 15 · Electromagnetic Waves

15.1 Displacement Current and Electromagnetic Waves

A changing electric field produces a magnetic field just as a current does. Adding this displacement current to Ampère's law lets electric and magnetic fields regenerate each other and travel through empty space as a wave — at the speed $c=1/\sqrt{\mu_0\varepsilon_0}$, with $E_0=cB_0$, carrying energy and momentum.

A phone in Chennai receives a call routed through a satellite 36 000 km above the equator; a radio telescope picks up a hiss that left a distant galaxy millions of years ago; sunlight warms your face eight minutes after leaving the Sun. Nothing material travels between the source and the receiver in any of these cases — no air, no wire, no string. What arrives is a disturbance of electric and magnetic fields that carries energy, momentum and information through empty space at $3.0\times10^8\ \text{m/s}$.

The existence of such waves was not discovered by experiment first. In the 1860s James Clerk Maxwell noticed that the laws of electricity and magnetism we met in Units 11–14 contradict each other when a capacitor is being charged. Repairing the contradiction meant adding one new term to Ampère's law — the displacement current — and with it the equations predicted waves of electric and magnetic field whose speed came out, from purely electrical measurements, equal to the measured speed of light. Heinrich Hertz produced and detected such waves in his laboratory in 1887. In this section we build the displacement current from the charging capacitor, state Maxwell's equations, list the characteristics of an electromagnetic wave — transverse, $\mathbf E$ and $\mathbf B$ in phase, $c=E_0/B_0$ — and work out the energy, intensity and momentum it carries.

Displacement current and the Ampère–Maxwell law

Ampère's circuital law (Section 13.1) says that around any closed loop $\oint\mathbf B\cdot d\mathbf l=\mu_0I_\text{enc}$, where $I_\text{enc}$ is the current crossing any surface whose edge is that loop. The word "any" is the key. For a steady current in a complete circuit it causes no trouble: whatever surface you choose, the same current crosses it.

Now charge a parallel-plate capacitor through a wire carrying a current $I$. Draw a small circular loop $C$ around the wire just before the left plate. Surface $S_1$ is the flat disc bounded by $C$; the wire pierces it, so Ampère's law gives $\oint\mathbf B\cdot d\mathbf l=\mu_0I$. Surface $S_2$ has the same edge $C$ but bulges out like a bag between the plates, so that no wire crosses it. No charge flows through the gap, so Ampère's law now gives $\oint\mathbf B\cdot d\mathbf l=0$. The same loop cannot have two different values of $\oint\mathbf B\cdot d\mathbf l$ — the law as it stands is inconsistent whenever currents are changing.

Maxwell looked at what does pass through $S_2$: the electric field between the plates, and that field is growing. With charge $q$ on plates of area $A$ (edge effects neglected), the field in the gap is $E=\dfrac{q}{\varepsilon_0A}$, so the electric flux through $S_2$ is $\Phi_E=EA=\dfrac{q}{\varepsilon_0}$. Differentiating,

$$\varepsilon_0\frac{d\Phi_E}{dt}=\frac{dq}{dt}=I .$$

The quantity $\varepsilon_0\,d\Phi_E/dt$ through $S_2$ is exactly equal to the conduction current through $S_1$. If we count it as a current, the contradiction disappears.

📘 Definition 15.1 — Displacement current

The displacement current through a surface is $\varepsilon_0$ times the rate of change of the electric flux through that surface:

$$i_d=\varepsilon_0\,\frac{d\Phi_E}{dt}.$$

It is measured in amperes. It is not a flow of charge: it exists wherever the electric field is changing — in the gap of a capacitor, in a dielectric, in empty space. The ordinary current carried by moving charges is called the conduction current $i_c$. In a medium of permittivity $\varepsilon$, replace $\varepsilon_0$ by $\varepsilon$.

📐 Law 15.1 — The Ampère–Maxwell law

For any closed loop, with $\Phi_E$ the electric flux through any surface bounded by the loop and $i_c$ the conduction current crossing that surface,

$$\oint\mathbf B\cdot d\mathbf l=\mu_0\left(i_c+i_d\right)=\mu_0\,i_c+\mu_0\varepsilon_0\,\frac{d\Phi_E}{dt}.$$

A changing electric field is a source of magnetic field, exactly as a current is. The total current $i_c+i_d$ is the same through every surface with the same edge, so it is continuous around a circuit — conduction current in the wires, displacement current in the gap. For steady currents and static fields $i_d=0$ and the law reduces to Ampère's law.

For a parallel-plate capacitor of capacitance $C=\varepsilon_0A/d$ with potential difference $V$ across the gap, $E=V/d$ and $\Phi_E=EA$, so the displacement current through the gap can be written in three useful ways:

$$i_d=\varepsilon_0A\,\frac{dE}{dt}=C\,\frac{dV}{dt}=\frac{dq}{dt}.$$

If a sinusoidal voltage $V=V_0\sin\omega t$ is applied, $i_d=C\omega V_0\cos\omega t$: an alternating displacement current of amplitude $C\omega V_0$ flows across the gap, which is why a capacitor "passes" AC (Section 14.3) although no charge ever crosses it. With a steady DC supply, once the capacitor is fully charged $dV/dt=0$, so $i_d=0$ and $i_c=0$ together.

The displacement current makes a magnetic field in the gap, and we can find it with the Ampère–Maxwell law exactly as we found the field of a wire with Ampère's law.

📐 Result 15.2 — Magnetic field between the plates of a charging capacitor

A capacitor with circular plates of radius $R$ (small gap, uniform field between the plates, edge effects neglected) is charged by a current $I$. At a distance $r$ from the axis, in the region between the planes of the plates, the field lines of $\mathbf B$ are circles about the axis and

$$B=\frac{\mu_0 I\,r}{2\pi R^2}\quad(r\le R),\qquad B=\frac{\mu_0 I}{2\pi r}\quad(r\ge R).$$

$B$ rises linearly from zero on the axis to its greatest value $\mu_0I/2\pi R$ at the rim, and outside falls off exactly as the field of a long straight wire carrying $I$.

Derivation. Take a circle of radius $r\le R$ coaxial with the plates, in the gap, and the flat disc it bounds. No conduction current crosses the disc. The field $E=q/(\varepsilon_0\pi R^2)$ is uniform, so the flux through the disc is $\Phi_E=E\,\pi r^2=\dfrac{q}{\varepsilon_0}\dfrac{r^2}{R^2}$, and $i_d=\varepsilon_0\dfrac{d\Phi_E}{dt}=I\dfrac{r^2}{R^2}$ — only the fraction $r^2/R^2$ of the displacement current passes through this smaller disc. By symmetry $B$ has the same size all round the circle and is tangent to it, so $B\cdot2\pi r=\mu_0I\dfrac{r^2}{R^2}$, giving the first formula. For $r\ge R$ the disc catches all the flux, $i_d=I$, and $B\cdot2\pi r=\mu_0I$. The direction follows the right-hand rule with the thumb along $i_d$, which points the same way as the conduction current (from the plate being charged positive towards the other).

✏️ Example 1 — Current that crosses an empty gap
A parallel-plate capacitor has plates of area $0.050\ \text{m}^2$ separated by $1.0\ \text{mm}$ of air. While it is being charged, the electric field between the plates increases at $2.0\times10^{12}\ \text{V m}^{-1}\text{s}^{-1}$. Find (a) the displacement current between the plates, (b) the current in the connecting wires, (c) the rate at which the potential difference across the plates is rising, and check (b) using $C\,dV/dt$.
(a) $i_d=\varepsilon_0A\dfrac{dE}{dt}=8.85\times10^{-12}\times0.050\times2.0\times10^{12}=0.885\ \text{A}\approx0.89\ \text{A}$.
(b) The total current is continuous: the conduction current in the wires equals the displacement current in the gap, $0.89\ \text{A}$.
(c) $V=Ed$, so $\dfrac{dV}{dt}=d\dfrac{dE}{dt}=1.0\times10^{-3}\times2.0\times10^{12}=2.0\times10^9\ \text{V/s}$.
Check $C=\dfrac{\varepsilon_0A}{d}=\dfrac{8.85\times10^{-12}\times0.050}{1.0\times10^{-3}}=4.43\times10^{-10}\ \text{F}$, and $C\dfrac{dV}{dt}=4.43\times10^{-10}\times2.0\times10^9=0.885\ \text{A}$ ✓.
✏️ Example 2 — The magnetic field inside a charging capacitor
A capacitor with circular plates of radius $5.0\ \text{cm}$ is being charged by a steady current of $2.0\ \text{A}$. Find the magnetic field between the plates (a) $2.0\ \text{cm}$ from the axis, (b) at the rim of the plates, (c) $8.0\ \text{cm}$ from the axis, in the plane midway between the plates. (d) At what rate is the electric field between the plates changing? ($\mu_0=4\pi\times10^{-7}\ \text{T m/A}$.)
Find (a), the field $2.0\ \text{cm}$ from the axis, before you open the solution:
(a) $r\lt R$: $B=\dfrac{\mu_0Ir}{2\pi R^2}=\dfrac{2\times10^{-7}\times2.0\times0.020}{(0.050)^2}=3.2\times10^{-6}\ \text{T}=3.2\ \mu\text{T}$.
(b) $r=R$: $B=\dfrac{\mu_0I}{2\pi R}=\dfrac{2\times10^{-7}\times2.0}{0.050}=8.0\ \mu\text{T}$ — the largest value anywhere.
(c) $r\gt R$: $B=\dfrac{\mu_0I}{2\pi r}=\dfrac{2\times10^{-7}\times2.0}{0.080}=5.0\ \mu\text{T}$, the same as next to a long wire carrying $2.0\ \text{A}$.
(d) $I=\varepsilon_0\pi R^2\dfrac{dE}{dt}$, so $\dfrac{dE}{dt}=\dfrac{2.0}{8.85\times10^{-12}\times\pi\times(0.050)^2}=2.9\times10^{13}\ \text{V m}^{-1}\text{s}^{-1}$.
⏱ Shortcut Inside, $B\propto r$; outside, $B\propto1/r$; both meet at $B_\text{max}=\mu_0I/2\pi R$. So $B(r)=B_\text{max}\,(r/R)$ inside and $B_\text{max}\,(R/r)$ outside: $8.0\times\tfrac{2}{5}=3.2\ \mu\text{T}$ and $8.0\times\tfrac58=5.0\ \mu\text{T}$ with no new arithmetic.

In Interactive 1 set the charging current to $2.0\ \text{A}$ and the plate radius to $5.0\ \text{cm}$. Compare the magnetic field at $r=2.5\ \text{cm}$ (inside the plates) with the field at $r=10\ \text{cm}$ (outside). Which is larger?

Set $I=2.0\ \text{A}$, $R=5.0\ \text{cm}$ and move the probe: the B at the probe readout shows $4.00\ \mu\text{T}$ at $r=2.5\ \text{cm}$ and again $4.00\ \mu\text{T}$ at $r=10\ \text{cm}$, while B at the rim reads $8.00\ \mu\text{T}$. Inside, $B=B_\text{max}(r/R)=8.00\times\tfrac12$; outside, $B=B_\text{max}(R/r)=8.00\times\tfrac12$. The small circle encloses only a quarter of the displacement current, but it is also only half as long, so $B\propto r$ inside; the big circle encloses all of it but is twice as long as the rim, so $B\propto1/r$ outside. Radii with $r_1r_2=R^2$ always give the same field. The field is not zero inside: the changing $\mathbf E$ (displacement current) is its source. The readout $dE/dt=2.88\times10^{13}\ \text{V m}^{-1}\text{s}^{-1}$ is the rate at which that field grows.
Interactive 1 — Displacement Current in a Charging Capacitor

A steady current $I$ charges a capacitor with circular plates (seen edge-on). Press Play: charge piles up on the plates, the electric field lines between them (red) grow denser, and the dashed purple arrows show the displacement current $\varepsilon_0\,d\Phi_E/dt$ that carries the current across the gap. The blue ring is a circle of radius $r$ about the axis; the graph on the right plots $B$ against $r$ — rising linearly inside the plates and falling as $1/r$ outside. $\mu_0=4\pi\times10^{-7}\ \text{T m/A}$.

2.0 A5.0 cm2.5 cm
$i_d$ in the gap—
$dE/dt$ between plates—
B at the probe—
B at the rim (max)—

A capacitor is connected to a steady $12\ \text{V}$ battery and left for a long time. The displacement current between its plates is then

Electromagnetic waves and their characteristics

With the displacement current added, the four laws of electromagnetism you have met in this course form a complete set, known as Maxwell's equations. JEE Main needs them in words — what each one says — rather than in heavy mathematics.

📐 Law 15.3 — Maxwell's equations (integral form, in vacuum)
  1. Gauss's law for $\mathbf E$: $\oint\mathbf E\cdot d\mathbf A=\dfrac{q_\text{enc}}{\varepsilon_0}$ — electric field lines begin and end on charges (Section 11.2).
  2. Gauss's law for $\mathbf B$: $\oint\mathbf B\cdot d\mathbf A=0$ — there are no magnetic charges; magnetic field lines form closed loops.
  3. Faraday's law: $\oint\mathbf E\cdot d\mathbf l=-\dfrac{d\Phi_B}{dt}$ — a changing magnetic flux produces an electric field (Section 14.1).
  4. Ampère–Maxwell law: $\oint\mathbf B\cdot d\mathbf l=\mu_0i_c+\mu_0\varepsilon_0\dfrac{d\Phi_E}{dt}$ — currents and changing electric flux produce a magnetic field.

The integrals run over closed surfaces (1, 2) or round closed loops (3, 4). Together with the force law $\mathbf F=q(\mathbf E+\mathbf v\times\mathbf B)$ they describe all of classical electromagnetism.

Look at laws 3 and 4 side by side in empty space, where $q=0$ and $i_c=0$. A changing $\mathbf B$ creates an $\mathbf E$; a changing $\mathbf E$ creates a $\mathbf B$. If the fields are made to change somewhere, each keeps regenerating the other in the neighbouring region, and the disturbance spreads outwards on its own — no medium is needed, because the fields themselves are what is waving. That self-sustaining disturbance is an electromagnetic wave.

What produces them. A charge at rest has only an electric field. A charge moving with constant velocity makes a steady current-like magnetic field that moves along with it, but it does not radiate. To launch a wave the fields must change in time in a way that breaks away from the charge: an accelerated charge radiates electromagnetic waves. A charge oscillating at frequency $\nu$ — electrons surging back and forth in a transmitting aerial, or in an LC circuit — sends out waves of the same frequency $\nu$. Hertz did exactly this in 1887: a spark across a gap in an oscillating circuit produced radio waves that made sparks jump across a gap in a separate receiving loop across the room. Jagadish Chandra Bose in Kolkata produced and detected waves only millimetres to centimetres long in 1895, and Guglielmo Marconi sent radio signals across the Atlantic in 1901.

📘 Definition 15.2 — Electromagnetic wave

An electromagnetic wave is a travelling disturbance of electric and magnetic fields that sustain each other: the time-varying electric field produces the magnetic field and the time-varying magnetic field produces the electric field. It is produced by accelerated charges and needs no material medium.

Far from its source, a small patch of an electromagnetic wave is a plane wave: the fields are the same everywhere on each plane perpendicular to the direction of travel. For a plane wave travelling along $+z$ with its electric field along $x$,

$$E_x=E_0\sin(kz-\omega t),\qquad B_y=B_0\sin(kz-\omega t),$$

exactly the form of a progressive wave in Section 10.3, with angular wave number $k=2\pi/\lambda$, angular frequency $\omega=2\pi\nu$ and speed $v=\omega/k=\nu\lambda$. Substituting these fields into laws 3 and 4 (a calculation beyond JEE Main) gives two conditions: the wave must travel at $1/\sqrt{\mu_0\varepsilon_0}$, and $E_0=B_0/\sqrt{\mu_0\varepsilon_0}$. The numbers are worth doing once:

$$\frac{1}{\sqrt{\mu_0\varepsilon_0}}=\frac{1}{\sqrt{4\pi\times10^{-7}\times8.85\times10^{-12}}}=3.00\times10^8\ \text{m/s}.$$

Two constants measured with charges, currents, coils and capacitors give the speed of light. Maxwell concluded that light is an electromagnetic wave.

📐 Result 15.4 — Characteristics of an electromagnetic wave
  1. Transverse. $\mathbf E$ and $\mathbf B$ are both perpendicular to the direction of propagation and to each other. The direction of travel is the direction of $\mathbf E\times\mathbf B$.
  2. In phase. $\mathbf E$ and $\mathbf B$ reach their maxima, pass through zero and reverse together, at the same place and the same instant.
  3. Speed in vacuum. Every electromagnetic wave, whatever its frequency, travels in vacuum at $c=\dfrac{1}{\sqrt{\mu_0\varepsilon_0}}=3.0\times10^8\ \text{m/s}$, and $c=\nu\lambda$.
  4. Ratio of fields. $\dfrac{E_0}{B_0}=c$, and at every point and instant $E=cB$.
  5. In a medium of permittivity $\varepsilon=\varepsilon_r\varepsilon_0$ and permeability $\mu=\mu_r\mu_0$, the speed is $v=\dfrac{1}{\sqrt{\mu\varepsilon}}=\dfrac{c}{n}$ with refractive index $n=\sqrt{\varepsilon_r\mu_r}$, and $E_0=vB_0$. The frequency is fixed by the source and does not change on entering a medium; the wavelength becomes $\lambda/n$.
  6. The wave needs no medium, is not deflected by electric or magnetic fields (it carries no charge), and carries energy and momentum.

Because the wave is transverse, the electric field can point in any direction across the line of travel. A wave whose $\mathbf E$ always oscillates along one fixed line is said to be plane-polarised — the subject of Section 16.5. Polarisation is impossible for a longitudinal wave such as sound, and its existence for light is direct evidence that light is transverse.

🧭 Problem-solving strategy — Reading a wave from its equation
  1. Match the given field with $E_0\sin(kx-\omega t)$: the amplitude is $E_0$, the number multiplying the position is $k$, the number multiplying $t$ is $\omega$.
  2. The wave travels along $+x$ if the phase is $kx-\omega t$, along $-x$ if it is $kx+\omega t$. Check that $\omega/k=3.0\times10^8\ \text{m/s}$ (in vacuum) — if not, the wave is in a medium.
  3. $\lambda=\dfrac{2\pi}{k}$, $\ \nu=\dfrac{\omega}{2\pi}$, $\ B_0=\dfrac{E_0}{c}$ (in vacuum).
  4. Direction of $\mathbf B$: it must make $\mathbf E\times\mathbf B$ point along the direction of travel. Use $\hat{\mathbf i}\times\hat{\mathbf j}=\hat{\mathbf k}$, $\hat{\mathbf j}\times\hat{\mathbf k}=\hat{\mathbf i}$, $\hat{\mathbf k}\times\hat{\mathbf i}=\hat{\mathbf j}$.
  5. Write $\mathbf B$ with the same phase $(kx-\omega t)$ as $\mathbf E$ — they are in phase.
✏️ Example 3 — Everything from one equation
The electric field of a plane electromagnetic wave in vacuum is $\mathbf E=60\sin\left(2.0\times10^{7}x-6.0\times10^{15}t\right)\hat{\mathbf j}\ \text{V/m}$ (SI units). Find (a) the direction of propagation and the speed, (b) the wavelength and frequency, (c) the amplitude and direction of the magnetic field, and write $\mathbf B$ as a function of $x$ and $t$.
Find the amplitude of the magnetic field before you open the solution:
(a) The phase is $kx-\omega t$, so the wave travels along $+x$. Speed $v=\dfrac{\omega}{k}=\dfrac{6.0\times10^{15}}{2.0\times10^{7}}=3.0\times10^8\ \text{m/s}$ — it is in vacuum, as stated.
(b) $\lambda=\dfrac{2\pi}{k}=\dfrac{6.283}{2.0\times10^7}=3.14\times10^{-7}\ \text{m}=314\ \text{nm}$; $\ \nu=\dfrac{\omega}{2\pi}=\dfrac{6.0\times10^{15}}{6.283}=9.55\times10^{14}\ \text{Hz}$. (Check: $\nu\lambda=3.0\times10^8\ \text{m/s}$ ✓.)
(c) $B_0=\dfrac{E_0}{c}=\dfrac{60}{3.0\times10^8}=2.0\times10^{-7}\ \text{T}$. $\mathbf E$ is along $\hat{\mathbf j}$ and $\mathbf E\times\mathbf B$ must be along $\hat{\mathbf i}$; since $\hat{\mathbf j}\times\hat{\mathbf k}=\hat{\mathbf i}$, $\mathbf B$ is along $+\hat{\mathbf k}$.
B(x, t) $\mathbf B=2.0\times10^{-7}\sin\left(2.0\times10^{7}x-6.0\times10^{15}t\right)\hat{\mathbf k}\ \text{T}$ — same phase as $\mathbf E$.
Note A wavelength of $314\ \text{nm}$ is just shorter than violet light: this is ultraviolet radiation (Section 15.2 sorts the bands). The magnetic field, $0.2\ \mu\text{T}$, is a hundred times weaker than the Earth's field — yet the wave carries as much energy in its $\mathbf B$ as in its $\mathbf E$, as we shall see.
✏️ Example 4 — Entering a medium
An electromagnetic wave of frequency $5.0\times10^{14}\ \text{Hz}$ travels in vacuum and then enters a transparent non-magnetic medium of relative permittivity $\varepsilon_r=2.25$ (at this frequency). Find (a) its wavelength in vacuum, (b) its speed, frequency and wavelength in the medium, (c) the ratio $E_0/B_0$ in the medium.
(a) $\lambda_0=\dfrac{c}{\nu}=\dfrac{3.0\times10^8}{5.0\times10^{14}}=6.0\times10^{-7}\ \text{m}=600\ \text{nm}$.
(b) $n=\sqrt{\varepsilon_r\mu_r}=\sqrt{2.25\times1}=1.5$, so $v=\dfrac{c}{n}=2.0\times10^8\ \text{m/s}$. The frequency stays $5.0\times10^{14}\ \text{Hz}$ (it is set by the source). $\lambda=\dfrac{v}{\nu}=\dfrac{2.0\times10^8}{5.0\times10^{14}}=4.0\times10^{-7}\ \text{m}=400\ \text{nm}=\lambda_0/n$.
(c) $\dfrac{E_0}{B_0}=v=2.0\times10^8\ \text{m/s}$ in the medium (not $c$).
Check $v=\dfrac{1}{\sqrt{\mu_0\varepsilon_r\varepsilon_0}}=\dfrac{c}{\sqrt{\varepsilon_r}}=\dfrac{3.0\times10^8}{1.5}$ ✓. The light does not change colour inside the medium: colour goes with frequency, and the frequency is unchanged.

In Interactive 2 set $E_0=300\ \text{V/m}$ and $\nu=500\ \text{MHz}$ in vacuum, then switch to the medium with $\varepsilon_r=2.25$. What happens to the wavelength and the frequency?

In vacuum the readouts show $\lambda=0.600\ \text{m}$, speed $3.00\times10^8\ \text{m/s}$, $B_0=1.00\ \mu\text{T}$ and intensity $119\ \text{W/m}^2$. Choosing $\varepsilon_r=2.25$ ($n=1.5$) packs more waves into the same stretch of space: $\lambda=0.400\ \text{m}$, speed $2.00\times10^8\ \text{m/s}$, and $B_0=E_0/v=1.50\ \mu\text{T}$. The frequency is set by the source and cannot change — the wave crests arrive at a boundary at the rate the source makes them — so the slower speed must show up as a shorter wavelength, $\lambda=v/\nu$.
Interactive 2 — A Travelling Electromagnetic Wave

A plane wave travels to the right along the axis. The red curve is $\mathbf E$ (vertical); the blue curve is $\mathbf B$, drawn in the slanted plane that represents the direction out of the screen and scaled as $vB$ so that the two can be compared. Press Play to watch the crests move. The window shows $3.0\ \text{m}$ of space. Change the amplitude, the frequency and the medium and read off the wavelength, speed, magnetic amplitude and intensity.

300 V/m500 MHz
wavelength $\lambda$—
speed $v$—
$B_0=E_0/v$—
intensity $\tfrac12\varepsilon_0cE_0^2$ (vacuum)—

At a certain point in a plane electromagnetic wave travelling along $+z$ in vacuum, the electric field is momentarily $\mathbf E=+6.0\,\hat{\mathbf i}\ \text{V/m}$. The magnetic field at that point and instant is

Energy, intensity and momentum of electromagnetic waves

In Section 11.4 we found that an electric field stores energy $\tfrac12\varepsilon_0E^2$ per unit volume, and in Section 14.2 that a magnetic field stores $B^2/2\mu_0$ per unit volume. An electromagnetic wave has both fields, so the space it passes through holds energy. With $B=E/c$ and $c^2=1/\mu_0\varepsilon_0$,

$$u_B=\frac{B^2}{2\mu_0}=\frac{E^2}{2\mu_0c^2}=\frac{\varepsilon_0E^2}{2}=u_E .$$

The energy is shared equally between the electric and the magnetic fields, although $B$ looks tiny in SI units. The total energy density at a point is $u=u_E+u_B=\varepsilon_0E^2$; as the fields oscillate it varies between zero and $\varepsilon_0E_0^2$, and since the average of $\sin^2$ over a cycle is $\tfrac12$ its time average is $\tfrac12\varepsilon_0E_0^2$.

📘 Definition 15.3 — Intensity of a wave

The intensity $I$ of a wave is the average energy it carries per unit time across unit area held perpendicular to the direction of travel. Its SI unit is $\text{W/m}^2$. In one second the energy in a column of length $c$ and cross-section $1\ \text{m}^2$ crosses that area, so $I=\bar u\,c$.

📐 Result 15.5 — Energy density and intensity of an electromagnetic wave

For a plane electromagnetic wave in vacuum with field amplitudes $E_0=cB_0$ (rms values $E_\text{rms}=E_0/\sqrt2$):

$$\bar u_E=\bar u_B=\tfrac14\varepsilon_0E_0^2,\qquad \bar u=\tfrac12\varepsilon_0E_0^2=\frac{B_0^2}{2\mu_0}=\varepsilon_0E_\text{rms}^2,$$ $$I=\bar u\,c=\tfrac12\varepsilon_0cE_0^2=\frac{cB_0^2}{2\mu_0}=\frac{E_0B_0}{2\mu_0}.$$

For a point source radiating a power $P$ equally in all directions (no absorption), the same power crosses every sphere around it, so $I=\dfrac{P}{4\pi r^2}$: intensity falls as $1/r^2$ and the field amplitudes as $1/r$.

A wave that carries energy also carries momentum. Maxwell's theory shows that when a wave delivers energy $U$ to a surface it also delivers linear momentum of magnitude $U/c$ along its direction of travel. The momentum delivered per second is a force; per unit area it is a pressure, called radiation pressure.

📐 Result 15.6 — Momentum and radiation pressure

Electromagnetic radiation of energy $U$ falling normally on a surface transfers momentum

$$p=\frac{U}{c}\ \ \text{(completely absorbed)},\qquad p=\frac{2U}{c}\ \ \text{(completely reflected back)}.$$

For a beam of intensity $I$ falling normally on an area $A$ (so the power is $P=IA$), the force and the radiation pressure are

$$F=\frac{IA}{c},\ \ p_\text{rad}=\frac{I}{c}\ \ \text{(absorbed)};\qquad F=\frac{2IA}{c},\ \ p_\text{rad}=\frac{2I}{c}\ \ \text{(reflected)}.$$

A surface that absorbs a fraction of the light and reflects the rest receives a pressure between these two limits.

The factor 2 for reflection is the same as for a ball bouncing straight back off a wall: the momentum is reversed, so the change is twice the momentum brought in. Radiation pressure is tiny in everyday life — full sunlight pushes on an absorbing surface with about $5\ \mu\text{Pa}$ — but it is real. It nudges the orbits of satellites, pushes the tails of comets away from the Sun, and has been used to steer "solar sail" spacecraft such as Japan's IKAROS (2010).

✏️ Example 5 — The fields near a lamp
A $100\ \text{W}$ lamp converts $5.0\%$ of its electrical power into visible light, radiated uniformly in all directions. Treating it as a point source, find at a distance of $2.0\ \text{m}$ (a) the intensity of the visible light, (b) the amplitude and the rms value of its electric field, (c) the amplitude of its magnetic field, (d) the average energy density. ($\varepsilon_0=8.85\times10^{-12}\ \text{C}^2\text{N}^{-1}\text{m}^{-2}$, $c=3.0\times10^8\ \text{m/s}$.)
Find the electric-field amplitude, part (b), first:
(a) Visible power $P=0.050\times100=5.0\ \text{W}$. $I=\dfrac{P}{4\pi r^2}=\dfrac{5.0}{4\pi\times(2.0)^2}=9.95\times10^{-2}\ \text{W/m}^2$.
(b) $E_0=\sqrt{\dfrac{2I}{\varepsilon_0c}}=\sqrt{\dfrac{2\times0.0995}{8.85\times10^{-12}\times3.0\times10^8}}=\sqrt{74.9}=8.66\ \text{V/m}$; $\ E_\text{rms}=\dfrac{E_0}{\sqrt2}=6.12\ \text{V/m}$.
(c) $B_0=\dfrac{E_0}{c}=\dfrac{8.66}{3.0\times10^8}=2.89\times10^{-8}\ \text{T}$.
(d) $\bar u=\dfrac{I}{c}=\dfrac{0.0995}{3.0\times10^8}=3.32\times10^{-10}\ \text{J/m}^3$ (check: $\tfrac12\varepsilon_0E_0^2=\tfrac12\times8.85\times10^{-12}\times75.0=3.32\times10^{-10}$ ✓).
⏱ Shortcut $\tfrac12\varepsilon_0c=1.33\times10^{-3}\ \text{W/V}^2$ (often written $\tfrac{1}{2\times377}$, since $\tfrac{1}{\varepsilon_0c}=\mu_0c\approx377\ \Omega$). So $E_0=\sqrt{I/1.33\times10^{-3}}=\sqrt{753I}$: for $I=0.0995$, $E_0=\sqrt{74.9}$.
✏️ Example 6 — Pushing with sunlight
Sunlight of intensity $1.4\ \text{kW/m}^2$ falls normally on a flat surface of area $2.0\ \text{m}^2$ for one hour. Find (a) the energy delivered, (b) the momentum delivered and the average force if the surface absorbs all the light, (c) the force if instead it is a perfect mirror, (d) the amplitudes $E_0$ and $B_0$ of the sunlight's fields (treat the sunlight as a single plane wave).
(a) $U=IAt=1.4\times10^3\times2.0\times3600=1.01\times10^7\ \text{J}$.
(b) Absorbed: $p=\dfrac{U}{c}=\dfrac{1.008\times10^7}{3.0\times10^8}=3.4\times10^{-2}\ \text{kg m/s}$. Force $F=\dfrac{p}{t}=\dfrac{IA}{c}=\dfrac{2800}{3.0\times10^8}=9.3\times10^{-6}\ \text{N}$.
(c) Reflected straight back: $F=\dfrac{2IA}{c}=1.9\times10^{-5}\ \text{N}$ — twice as large.
(d) $E_0=\sqrt{\dfrac{2I}{\varepsilon_0c}}=\sqrt{\dfrac{2800}{2.655\times10^{-3}}}=1.03\times10^3\ \text{V/m}$; $\ B_0=\dfrac{E_0}{c}=3.4\times10^{-6}\ \text{T}$.
Check Radiation pressure on the absorber $I/c=4.7\times10^{-6}\ \text{Pa}$ — numerically equal to the average energy density $\bar u=I/c$ in $\text{J/m}^3$. That is no coincidence: pressure and energy density have the same units, and for an absorber at normal incidence they are equal.
⚠️ JEE Main traps

1. Displacement current is not moving charge. No charge crosses a capacitor gap. $i_d=\varepsilon_0\,d\Phi_E/dt$ depends on the rate of change of the field; for a fully charged capacitor on DC it is zero, however large $E$ is.

2. Upside-down ratio. $E_0=cB_0$, so $B_0=E_0/c$ is tiny ($10^{-8}$ T for a few V/m). Writing $B_0=cE_0$ gives absurd fields of $10^9$ T. In a medium the ratio is $v$, not $c$.

3. "The electric field carries most of the energy". No: $u_E=u_B$ at every point and instant. $B$ only looks small because of SI units.

4. Peak, rms and average. $I=\tfrac12\varepsilon_0cE_0^2$ uses the amplitude with a factor $\tfrac12$; with rms values it is $\varepsilon_0cE_\text{rms}^2$ with no $\tfrac12$. The instantaneous energy density $\varepsilon_0E^2$ is twice the average at a crest.

5. Phase and frequency. $\mathbf E$ and $\mathbf B$ are in phase (not $90^\circ$ apart); entering a medium changes $v$ and $\lambda$ but never $\nu$. And radiation pressure on a mirror is $2I/c$, on an absorber $I/c$.

The average energy density of a plane electromagnetic wave is $\bar u$. Its electric field amplitude is doubled (same frequency). The new intensity is

Exercises

Take $c=3.0\times10^8\ \text{m/s}$, $\varepsilon_0=8.85\times10^{-12}\ \text{C}^2\text{N}^{-1}\text{m}^{-2}$ and $\mu_0=4\pi\times10^{-7}\ \text{T m/A}$. Waves are in vacuum unless a part says otherwise; capacitor gaps are small, with edge effects neglected.

I
Displacement current and the Ampère–Maxwell law.
  • 1 The potential difference across a $5.0\ \mu\text{F}$ capacitor is rising at $2.0\times10^4\ \text{V/s}$. Find the displacement current between its plates.
  • 2 Between the plates (area $0.010\ \text{m}^2$) of a parallel-plate capacitor, the electric field changes at $1.0\times10^{12}\ \text{V m}^{-1}\text{s}^{-1}$. Find the displacement current in milliamperes.
  • 3 Show from the units of $\varepsilon_0$ and of electric flux that $\varepsilon_0\,d\Phi_E/dt$ is measured in amperes.
  • 4 A capacitor is charged by a current of $0.50\ \text{A}$. At what rate is the electric flux between its plates changing?
  • 5 A capacitor with circular plates of radius $4.0\ \text{cm}$ is charged by a current of $1.6\ \text{A}$. Find the magnetic field between the plates $2.0\ \text{cm}$ from the axis.
  • 6 For the capacitor in part 5, find the field $6.0\ \text{cm}$ from the axis (between the planes of the plates), and the greatest field anywhere in that plane.
  • 7 A capacitor has been connected to a $9.0\ \text{V}$ DC supply for an hour. What are the conduction current in its leads and the displacement current in its gap? Explain.
  • 8 A $2.0\ \text{nF}$ capacitor is connected to an AC source $V=50\sin(5.0\times10^5t)$ volts. Find the amplitude of the displacement current between the plates, and say how it compares with the current in the leads.
1 $i_d=C\dfrac{dV}{dt}=5.0\times10^{-6}\times2.0\times10^4=0.10\ \text{A}$.
2 $i_d=\varepsilon_0A\dfrac{dE}{dt}=8.85\times10^{-12}\times0.010\times1.0\times10^{12}=8.85\times10^{-2}\ \text{A}=88.5\ \text{mA}$.
3 $\varepsilon_0$: $\text{C}^2\text{N}^{-1}\text{m}^{-2}$; flux $\Phi_E=EA$: $\text{N C}^{-1}\text{m}^2$. Product per second: $\text{C}^2\text{N}^{-1}\text{m}^{-2}\cdot\text{N C}^{-1}\text{m}^2\cdot\text{s}^{-1}=\text{C/s}=\text{A}$ ✓.
4 $\dfrac{d\Phi_E}{dt}=\dfrac{i_d}{\varepsilon_0}=\dfrac{0.50}{8.85\times10^{-12}}=5.6\times10^{10}\ \text{V m s}^{-1}$ (i.e. $\text{N m}^2\text{C}^{-1}\text{s}^{-1}$).
5 $r\lt R$: $B=\dfrac{\mu_0Ir}{2\pi R^2}=\dfrac{2\times10^{-7}\times1.6\times0.020}{(0.040)^2}=4.0\times10^{-6}\ \text{T}=4.0\ \mu\text{T}$.
6 $r\gt R$: $B=\dfrac{\mu_0I}{2\pi r}=\dfrac{2\times10^{-7}\times1.6}{0.060}=5.3\ \mu\text{T}$. Greatest at the rim: $\dfrac{2\times10^{-7}\times1.6}{0.040}=8.0\ \mu\text{T}$.
7 Both zero. The capacitor is fully charged, so no charge flows ($i_c=0$) and the field between the plates is steady ($d\Phi_E/dt=0$, $i_d=0$).
8 $i_d=C\dfrac{dV}{dt}=C\omega V_0\cos\omega t$; amplitude $2.0\times10^{-9}\times5.0\times10^5\times50=0.050\ \text{A}$. It is equal to the conduction current in the leads at every instant (continuity of total current); both lead the voltage by $90^\circ$.
II
Electromagnetic waves and their characteristics.
  • 1 Calculate $1/\sqrt{\mu_0\varepsilon_0}$ and say what it represents.
  • 2 The electric field amplitude of a plane wave in vacuum is $45\ \text{V/m}$. Find the magnetic field amplitude.
  • 3 The magnetic field amplitude of a plane wave in vacuum is $4.0\times10^{-8}\ \text{T}$. Find the electric field amplitude.
  • 4 A wave in vacuum has $\mathbf E=30\sin\left(1.0\times10^{7}z-3.0\times10^{15}t\right)\hat{\mathbf i}\ \text{V/m}$. Find its direction of travel, wavelength (in nm) and frequency.
  • 5 Write the magnetic field $\mathbf B(z,t)$ of the wave in part 4, with its direction.
  • 6 A wave travels along $-y$. At some point and instant its electric field points along $+z$. In which direction does its magnetic field point there?
  • 7 A $100\ \text{MHz}$ wave passes from vacuum into a non-magnetic medium with $\varepsilon_r=4.0$. Find its speed and wavelength in the medium.
  • 8 At a point in a plane wave in vacuum, the electric field is momentarily $6.0\ \text{V/m}$. What is the magnetic field there at that instant, and why can you answer without knowing the phase?
  • 9 The magnetic field of a wave in vacuum is $\mathbf B=2.0\times10^{-8}\sin\left(2.0\times10^{3}x-6.0\times10^{11}t\right)\hat{\mathbf k}\ \text{T}$. Find $E_0$, the wavelength and the frequency.
1 $\dfrac{1}{\sqrt{4\pi\times10^{-7}\times8.85\times10^{-12}}}=\dfrac{1}{\sqrt{1.112\times10^{-17}}}=3.00\times10^8\ \text{m/s}$: the speed of every electromagnetic wave in vacuum.
2 $B_0=\dfrac{E_0}{c}=\dfrac{45}{3.0\times10^8}=1.5\times10^{-7}\ \text{T}$.
3 $E_0=cB_0=3.0\times10^8\times4.0\times10^{-8}=12\ \text{V/m}$.
4 Phase $kz-\omega t$: along $+z$. $\lambda=\dfrac{2\pi}{1.0\times10^7}=6.28\times10^{-7}\ \text{m}=628\ \text{nm}$; $\nu=\dfrac{3.0\times10^{15}}{2\pi}=4.77\times10^{14}\ \text{Hz}$ (and $\omega/k=3.0\times10^8$ ✓).
5 $B_0=30/(3.0\times10^8)=1.0\times10^{-7}\ \text{T}$; $\hat{\mathbf i}\times\hat{\mathbf j}=\hat{\mathbf k}$, so $\mathbf B=1.0\times10^{-7}\sin\left(1.0\times10^{7}z-3.0\times10^{15}t\right)\hat{\mathbf j}\ \text{T}$.
6 Need $\hat{\mathbf k}\times\mathbf B$ along $-\hat{\mathbf j}$. Since $\hat{\mathbf k}\times\hat{\mathbf i}=\hat{\mathbf j}$, $\hat{\mathbf k}\times(-\hat{\mathbf i})=-\hat{\mathbf j}$: $\mathbf B$ points along $-x$.
7 $n=\sqrt{4.0}=2.0$: $v=1.5\times10^8\ \text{m/s}$; $\lambda=\dfrac{v}{\nu}=\dfrac{1.5\times10^8}{1.0\times10^8}=1.5\ \text{m}$ (it was $3.0\ \text{m}$ in vacuum; $\nu$ is unchanged).
8 $B=\dfrac{E}{c}=2.0\times10^{-8}\ \text{T}$. Because $\mathbf E$ and $\mathbf B$ are in phase, $E=cB$ holds at every point and instant, not only for the amplitudes.
9 $E_0=cB_0=6.0\ \text{V/m}$; $\lambda=\dfrac{2\pi}{2.0\times10^3}=3.14\times10^{-3}\ \text{m}=3.1\ \text{mm}$; $\nu=\dfrac{6.0\times10^{11}}{2\pi}=9.5\times10^{10}\ \text{Hz}$ (a microwave).
III
Energy, intensity and momentum.
  • 1 A plane wave has $E_0=50\ \text{V/m}$. Find its average energy density and its intensity.
  • 2 For the wave in part 1, find the ratio of the average electric energy density to the average magnetic energy density.
  • 3 Sunlight reaches the top of the atmosphere with an intensity of about $1.4\ \text{kW/m}^2$. Treating it as a plane wave, find $E_0$ and $B_0$.
  • 4 The rms electric field of a radio wave is $100\ \text{V/m}$. Find its intensity.
  • 5 A $40\ \text{W}$ point source radiates uniformly in all directions. Find the intensity and the electric field amplitude $5.0\ \text{m}$ away.
  • 6 A $3.0\ \text{mW}$ laser beam has a cross-section of $1.0\ \text{mm}^2$. Find its intensity and its electric field amplitude.
  • 7 A pulse of radiation carrying $30\ \text{J}$ falls normally on a surface. Find the momentum delivered if the surface (a) absorbs it, (b) reflects it straight back.
  • 8 Light of intensity $1.2\ \text{kW/m}^2$ falls normally on a perfectly reflecting plate of area $0.50\ \text{m}^2$. Find the force on it.
  • 9 You double your distance from a small lamp. By what factor do the intensity and the electric field amplitude change?
1 $\bar u=\tfrac12\varepsilon_0E_0^2=\tfrac12\times8.85\times10^{-12}\times2500=1.11\times10^{-8}\ \text{J/m}^3$; $I=\bar uc=3.32\ \text{W/m}^2$.
2 $1:1$ — the energy is always shared equally between $\mathbf E$ and $\mathbf B$.
3 $E_0=\sqrt{\dfrac{2I}{\varepsilon_0c}}=\sqrt{\dfrac{2800}{2.655\times10^{-3}}}=1.03\times10^3\ \text{V/m}$; $B_0=\dfrac{E_0}{c}=3.4\times10^{-6}\ \text{T}$.
4 $I=\varepsilon_0cE_\text{rms}^2=8.85\times10^{-12}\times3.0\times10^8\times10^4=26.6\ \text{W/m}^2$.
5 $I=\dfrac{40}{4\pi\times25}=0.127\ \text{W/m}^2$; $E_0=\sqrt{\dfrac{2\times0.127}{2.655\times10^{-3}}}=9.79\ \text{V/m}$.
6 $I=\dfrac{3.0\times10^{-3}}{1.0\times10^{-6}}=3.0\times10^3\ \text{W/m}^2$ — twice full sunlight; $E_0=\sqrt{\dfrac{6000}{2.655\times10^{-3}}}=1.5\times10^3\ \text{V/m}$.
7 (a) $p=\dfrac{U}{c}=\dfrac{30}{3.0\times10^8}=1.0\times10^{-7}\ \text{kg m/s}$; (b) $2.0\times10^{-7}\ \text{kg m/s}$.
8 $F=\dfrac{2IA}{c}=\dfrac{2\times1200\times0.50}{3.0\times10^8}=4.0\times10^{-6}\ \text{N}$.
9 $I\propto1/r^2$: the intensity falls to $\tfrac14$. $E_0\propto\sqrt I\propto1/r$: the amplitude halves.
IV
Harder problems and applications.
  • 1 Inside a charging capacitor with circular plates of radius $3.0\ \text{cm}$, the magnetic field $1.5\ \text{cm}$ from the axis is $2.0\ \mu\text{T}$. Find the charging current.
  • 2 The peak magnetic field of a radio signal at a receiver is $2.0\times10^{-10}\ \text{T}$. Find the electric field amplitude and the intensity at the receiver.
  • 3 The receiver in part 2 is $10\ \text{km}$ from a transmitter that radiates uniformly in all directions (ignore the ground). Estimate the transmitter's radiated power.
  • 4 (Modelling) A solar sail of area $1.0\times10^4\ \text{m}^2$, perfectly reflecting, faces the Sun where the intensity is $1.4\ \text{kW/m}^2$. Find the force on it and the acceleration of the $500\ \text{kg}$ spacecraft it pulls.
  • 5 A capacitor charged to $100\ \text{V}$ is connected across a $1.0\ \text{k}\Omega$ resistor. Find the displacement current in its gap just after the connection is made. Is the electric field in the gap growing or shrinking?
  • 6 Show that $1/\sqrt{\mu_0\varepsilon_0}$ has the dimensions of speed, and that $\varepsilon_0E^2$ has the dimensions of energy per unit volume.
  • 7 (Modelling) A mobile-phone tower aerial radiates $200\ \text{W}$; treat it as an isotropic point source. Find the intensity and the electric field amplitude $50\ \text{m}$ away. Public exposure guidelines at these frequencies are of the order of a few $\text{W/m}^2$ — how do your numbers compare?
1 $B=\dfrac{\mu_0Ir}{2\pi R^2}$ gives $I=\dfrac{2\pi R^2B}{\mu_0r}=\dfrac{(0.030)^2\times2.0\times10^{-6}}{2\times10^{-7}\times0.015}=0.60\ \text{A}$.
2 $E_0=cB_0=6.0\times10^{-2}\ \text{V/m}$; $I=\dfrac{cB_0^2}{2\mu_0}=\dfrac{3.0\times10^8\times4.0\times10^{-20}}{2\times4\pi\times10^{-7}}=4.8\times10^{-6}\ \text{W/m}^2$.
3 $P=4\pi r^2I=4\pi\times(1.0\times10^4)^2\times4.77\times10^{-6}=6.0\times10^3\ \text{W}=6.0\ \text{kW}$.
4 $F=\dfrac{2IA}{c}=\dfrac{2\times1400\times1.0\times10^4}{3.0\times10^8}=9.3\times10^{-2}\ \text{N}$; $a=\dfrac{F}{m}=1.9\times10^{-4}\ \text{m/s}^2$ — small, but it never stops: in a month it adds about $480\ \text{m/s}$.
5 The current is then $V/R=0.10\ \text{A}$, and the displacement current in the gap equals it: $0.10\ \text{A}$. The capacitor is discharging, so the field in the gap is shrinking; $i_d$ points opposite to $\mathbf E$, continuing the circulation of the conduction current round the circuit.
6 From $C=\varepsilon_0A/d$, $\varepsilon_0$ is measured in farads per metre; from $L=\mu_0n^2A\,l$ (solenoid), $\mu_0$ is in henries per metre. So $\mu_0\varepsilon_0$ is in $\text{H F/m}^2$. Since $1/\sqrt{LC}$ is an angular frequency, $\text{H F}=\text{s}^2$; hence $\mu_0\varepsilon_0$ is in $\text{s}^2/\text{m}^2$ and $1/\sqrt{\mu_0\varepsilon_0}$ in $\text{m/s}$, dimensions $[\text{LT}^{-1}]$. For the energy: $\varepsilon_0E^2$ has units $\text{C}^2\text{N}^{-1}\text{m}^{-2}\cdot\text{N}^2\text{C}^{-2}=\text{N/m}^2=\text{N m/m}^3=\text{J/m}^3$, dimensions $[\text{ML}^{-1}\text{T}^{-2}]$ ✓.
7 $I=\dfrac{200}{4\pi\times2500}=6.4\times10^{-3}\ \text{W/m}^2$; $E_0=\sqrt{\dfrac{2\times6.37\times10^{-3}}{2.655\times10^{-3}}}=2.2\ \text{V/m}$. This is about a thousand times below guideline values of a few $\text{W/m}^2$; real aerials beam their power sideways, so directly below a tower the intensity is lower still.
🎯 Exam corner JEE Main · MCQJEE Main · Numerical

E1. JEE Main · MCQ In a plane electromagnetic wave travelling in vacuum, the ratio of the average electric energy density to the average magnetic energy density is (A) $c$ (B) $1/c$ (C) $1$ (D) $c^2$

Idea $u_E=\tfrac12\varepsilon_0E^2$, $u_B=\dfrac{B^2}{2\mu_0}=\dfrac{E^2}{2\mu_0c^2}=\tfrac12\varepsilon_0E^2$, using $B=E/c$ and $\mu_0\varepsilon_0c^2=1$.
Answer (C) $1$.
⏱ Shortcut (A) and (D) come from comparing $E$ with $B$ (ratio $c$) instead of their energies. The energies are equal at every instant, so their averages are equal too.

E2. JEE Main · Numerical A parallel-plate capacitor has plates of area $0.20\ \text{m}^2$ separated by $0.885\ \text{mm}$ of air. The potential difference across it is increasing at $1.5\times10^7\ \text{V/s}$. Taking $\varepsilon_0=8.85\times10^{-12}\ \text{C}^2\text{N}^{-1}\text{m}^{-2}$, find the displacement current between the plates in mA. Give the answer to the nearest integer.

Capacitance $C=\dfrac{\varepsilon_0A}{d}=\dfrac{8.85\times10^{-12}\times0.20}{8.85\times10^{-4}}=2.0\times10^{-9}\ \text{F}$.
Current $i_d=C\dfrac{dV}{dt}=2.0\times10^{-9}\times1.5\times10^7=3.0\times10^{-2}\ \text{A}=30\ \text{mA}$.
Answer $30$.

E3. JEE Main · MCQ The electric field of a plane electromagnetic wave in vacuum is $\mathbf E=9.0\sin\left(2.0\times10^{6}x-6.0\times10^{14}t\right)\hat{\mathbf j}\ \text{V/m}$. The associated magnetic field, in tesla, is (A) $3.0\times10^{-8}\sin\left(2.0\times10^{6}x-6.0\times10^{14}t\right)\hat{\mathbf k}$ (B) $3.0\times10^{-8}\sin\left(2.0\times10^{6}x-6.0\times10^{14}t\right)\hat{\mathbf i}$ (C) $2.7\times10^{9}\sin\left(2.0\times10^{6}x-6.0\times10^{14}t\right)\hat{\mathbf k}$ (D) $3.0\times10^{-8}\cos\left(2.0\times10^{6}x-6.0\times10^{14}t\right)\hat{\mathbf k}$

Size $B_0=E_0/c=9.0/(3.0\times10^8)=3.0\times10^{-8}\ \text{T}$ — rules out (C), which multiplies by $c$.
Direction and phase The wave travels along $+x$ and $\mathbf E$ is along $\hat{\mathbf j}$; $\hat{\mathbf j}\times\hat{\mathbf k}=\hat{\mathbf i}$, so $\mathbf B$ is along $\hat{\mathbf k}$ — rules out (B), which is along the direction of travel. $\mathbf B$ is in phase with $\mathbf E$ (same sine) — rules out (D).
Answer (A).

E4. JEE Main · Numerical A parallel beam of light of power $60\ \text{W}$ falls normally on a perfectly reflecting mirror. Taking $c=3\times10^8\ \text{m/s}$, the force exerted on the mirror is $x\times10^{-8}\ \text{N}$. Find $x$. Give the answer to the nearest integer.

Idea In one second the beam brings energy $P$ and momentum $P/c$; on reflection the momentum is reversed, so the mirror receives $2P/c$ per second.
Force $F=\dfrac{2P}{c}=\dfrac{2\times60}{3\times10^8}=4.0\times10^{-7}\ \text{N}=40\times10^{-8}\ \text{N}$.
Answer $40$.
⏱ Shortcut $20$ is the trap answer for an absorbing surface ($P/c$). The area of the mirror is not needed — only the total power.

E5. JEE Main · MCQ Light from a small lamp radiating uniformly in all directions has an electric field amplitude of $12\ \text{V/m}$ at a distance of $2.0\ \text{m}$. At a distance of $6.0\ \text{m}$ the amplitude of its magnetic field is (A) $4.0\times10^{-8}\ \text{T}$ (B) $1.3\times10^{-8}\ \text{T}$ (C) $4.4\times10^{-9}\ \text{T}$ (D) $1.2\times10^{-7}\ \text{T}$

Scaling $I=P/4\pi r^2\propto E_0^2$, so $E_0\propto1/r$: at three times the distance $E_0=12/3=4.0\ \text{V/m}$.
Magnetic field $B_0=\dfrac{E_0}{c}=\dfrac{4.0}{3.0\times10^8}=1.3\times10^{-8}\ \text{T}$.
Answer (B).
⏱ Shortcut (C) uses $E_0\propto1/r^2$ (confusing amplitude with intensity); (A) forgets to scale the distance at all.

E6. JEE Main · Numerical A capacitor with circular plates of radius $6.0\ \text{cm}$ is being charged by a current of $3.0\ \text{A}$. The magnetic field between the plates at a distance of $3.0\ \text{cm}$ from the axis is $x\times10^{-7}\ \text{T}$. Taking $\mu_0=4\pi\times10^{-7}\ \text{T m/A}$, find $x$. Give the answer to the nearest integer.

Enclosed displacement current A circle of radius $r$ encloses the fraction $r^2/R^2=\tfrac14$ of the flux: $i_d=0.75\ \text{A}$.
Ampère–Maxwell $B\cdot2\pi r=\mu_0i_d$: $B=\dfrac{2\times10^{-7}\times0.75}{0.030}=5.0\times10^{-6}\ \text{T}=50\times10^{-7}\ \text{T}$.
Answer $50$.
⏱ Shortcut $B=B_\text{rim}\cdot\dfrac rR$ with $B_\text{rim}=\dfrac{\mu_0I}{2\pi R}=10\ \mu\text{T}$: half of it, $5.0\ \mu\text{T}$. Using the full $3.0\ \text{A}$ at $r=3.0\ \text{cm}$ gives the trap answer $200$.
🔬 Research–Teaching NexusResearch-tutored · optional, about 45 minutes

Research question. Can you measure the speed of light with a kitchen microwave oven and a plate of chocolate?

Why it matters. The speed of light links electricity and magnetism ($c=1/\sqrt{\mu_0\varepsilon_0}$), defines the metre, and sets the timing of GPS satellites, fibre-optic networks and radar. Inside a microwave oven the waves reflect off the metal walls and form a standing-wave pattern: hot spots half a wavelength apart, exactly like the antinodes of a stretched string. Measuring their spacing and reading the frequency off the label gives $c=\nu\lambda$.

What to do.

  1. Remove the turntable (or block it so it cannot rotate). Lay a flat bar of chocolate, a plate of grated cheese, or a sheet of thermal fax paper on a microwave-safe plate.
  2. Heat on low power for 15–30 seconds, only until a few separate spots begin to melt or darken. (Adult supervision; never run the oven empty or with metal inside.)
  3. Measure the distance between neighbouring melted spots along one direction. Repeat in several places and take the mean; the spacing is $\lambda/2$.
  4. Read the oven's operating frequency (usually $2450\ \text{MHz}$) from its label. Calculate $c=2\times(\text{spacing})\times\nu$ and its percentage difference from $3.00\times10^8\ \text{m/s}$. Estimate the uncertainty from the spread of your spacings.

Tools: Microwave oven, chocolate bar or cheese, ruler with mm scale, calculator or spreadsheet.

Hand in: A photo of the melted pattern with the ruler, a table of spacings, your value of $c$ with an uncertainty, and two sentences on the main sources of error.

Going further. The pattern inside an oven is three-dimensional, and not every pair of hot spots is exactly $\lambda/2$ apart along your ruler. Why do ovens have turntables or rotating "stirrers"? Try two different foods: does the result depend on the food? Why should it not?

Instructor note: with $\nu=2.45\ \text{GHz}$, $\lambda=12.2\ \text{cm}$ and the hot-spot spacing is about $6.1\ \text{cm}$; careful students typically get $c$ within 5–10 %. The largest errors come from judging the centre of a melted spot and from spots that lie on a diagonal of the 3-D pattern. Stress safety: low power, short times, no metal.

🧪 Self-check quiz

0/5 correct

Q1. A displacement current flows

Q2. In a plane electromagnetic wave, the electric and magnetic fields are

Q3. Radio waves and X-rays travelling in vacuum have

Q4. A plane electromagnetic wave in vacuum has electric field amplitude $E_0$. Its intensity is

Q5. A pulse of light carrying energy $U$ falls normally on a perfectly reflecting surface. The momentum it gives the surface is