Chapter 13 · Magnetic Effects of Current and Magnetism

13.2 Magnetic Forces, Torque on a Loop and the Galvanometer

A magnetic field pushes sideways on a moving charge, $\mathbf F=q\mathbf v\times\mathbf B$. Charged particles circle and spiral, crossed electric and magnetic fields pick out one speed, current-carrying wires push and pull on each other, and a coil in a field feels a torque $NIAB\sin\theta$ — the working principle of the moving-coil galvanometer, the ammeter and the voltmeter.

An electron beam in an old television tube, a proton in a medical accelerator, a charged particle from the Sun spiralling into the polar sky to light up an aurora — all are steered by magnetic fields. So are the wires of every electric motor and loudspeaker, and the coil of the meter that measured current in physics laboratories for a century. In § 13.1 we learned to calculate the field $\mathbf B$ produced by currents. Now we ask what that field does.

The answer starts from a single law — the magnetic force on a moving charge — and grows in steps. A charge in a uniform field moves in a circle or a helix; adding an electric field gives a device that selects one speed. A wire carrying current is a stream of moving charges, so it feels a force too; two such wires attract or repel, which is how the ampere was defined. A loop of wire feels a turning effect, and putting that torque against a spring gives the moving-coil galvanometer, which we finally convert into an ammeter and a voltmeter. We use vector products (§ 2.2), circular motion (§ 2.4), torque (§ 5.2) and resistor networks (§ 12.2).

Force on a moving charge: circles and helices

📐 Law 13.8 — The Lorentz force

A point charge $q$ moving with velocity $\mathbf v$ through a region with electric field $\mathbf E$ and magnetic field $\mathbf B$ feels the force

$$\mathbf F=q\left(\mathbf E+\mathbf v\times\mathbf B\right).$$

The magnetic part $q\,\mathbf v\times\mathbf B$ has magnitude $qvB\sin\theta$ ($\theta$ the angle between $\mathbf v$ and $\mathbf B$) and is perpendicular to both $\mathbf v$ and $\mathbf B$; for a negative charge it points the opposite way to $\mathbf v\times\mathbf B$. It is zero for a charge at rest or moving along the field.

Because the magnetic force is always perpendicular to the velocity, it does no work: $\mathbf F\cdot\mathbf v=0$. A magnetic field can change the direction of a charged particle's motion but never its speed or kinetic energy. To speed particles up, accelerators use electric fields; magnetic fields only steer them.

Velocity perpendicular to a uniform field. The force $qvB$ is constant in size and always perpendicular to $\mathbf v$ — exactly the condition for uniform circular motion (§ 2.4). The magnetic force supplies the centripetal force:

$$qvB=\frac{mv^2}{r}\qquad\Longrightarrow\qquad r=\frac{mv}{qB},\qquad T=\frac{2\pi r}{v}=\frac{2\pi m}{qB}.$$

The striking result is that the period does not depend on the speed: a faster particle moves on a bigger circle and takes exactly the same time to go round. The angular frequency $\omega=qB/m$ is called the cyclotron frequency.

Velocity at an angle to the field. Split $\mathbf v$ into a component $v_\parallel=v\cos\theta$ along $\mathbf B$ and $v_\perp=v\sin\theta$ across it. The parallel component feels no force and stays constant; the perpendicular component turns in a circle. Together they give a helix wound round the field lines.

📐 Result 13.9 — Charged particle in a uniform magnetic field

A particle of mass $m$ and charge $q$ moving with speed $v$ at angle $\theta$ to a uniform magnetic field $\mathbf B$ (no other forces) moves on a helix whose axis is along $\mathbf B$, with

$$r=\frac{mv\sin\theta}{qB},\qquad T=\frac{2\pi m}{qB},\qquad p_\text{helix}=v\cos\theta\;T=\frac{2\pi mv\cos\theta}{qB}.$$

For $\theta=90^\circ$ the path is a circle of radius $r=\dfrac{mv}{qB}=\dfrac{p}{qB}=\dfrac{\sqrt{2mK}}{qB}$ ($p$ = momentum, $K$ = kinetic energy); for a particle accelerated from rest through a potential difference $V$, $K=qV$ and $r=\dfrac{1}{B}\sqrt{\dfrac{2mV}{q}}$. For $\theta=0$ the particle moves straight along the field. The speed and kinetic energy never change.

📘 Definition 13.3 — Pitch of the helix

The pitch of the helical path is the distance the particle moves along the field direction during one revolution: $p_\text{helix}=v_\parallel T=\dfrac{2\pi mv\cos\theta}{qB}$.

Fast charged particles from the Sun are trapped in this way by the Earth's field: they spiral along the field lines towards the poles, where they strike the upper atmosphere and make it glow as the aurora. The same spiralling confines the hot plasma in fusion reactors.

✏️ Example 1 — A proton and an electron in the same field
A proton moving at $2.0\times10^6\ \text{m/s}$ enters a uniform field of $0.10\ \text{T}$ at right angles to it. (a) Find the force on it, the radius of its path and its period and frequency of revolution. (b) Find the radius and period for an electron with the same speed. (c) How much work does the field do on the proton in one revolution? ($m_p=1.67\times10^{-27}\ \text{kg}$, $m_e=9.1\times10^{-31}\ \text{kg}$, $e=1.6\times10^{-19}\ \text{C}$.)
(a) $F=evB=1.6\times10^{-19}\times2.0\times10^6\times0.10=3.2\times10^{-14}\ \text{N}$. $r=\dfrac{mv}{eB}=\dfrac{1.67\times10^{-27}\times2.0\times10^6}{1.6\times10^{-19}\times0.10}=0.209\ \text{m}$. $T=\dfrac{2\pi m}{eB}=6.56\times10^{-7}\ \text{s}$, so $f=1.52\times10^6\ \text{Hz}$.
(b) The radius and period scale with the mass: $r_e=\dfrac{9.1\times10^{-31}\times2.0\times10^6}{1.6\times10^{-20}}=1.14\times10^{-4}\ \text{m}=0.114\ \text{mm}$; $T_e=3.57\times10^{-10}\ \text{s}$. The electron also goes round the other way.
(c) Zero — the force is always perpendicular to the velocity, so the speed stays $2.0\times10^6\ \text{m/s}$.
Check The speed round the circle: $2\pi r/T=2\pi\times0.209/6.56\times10^{-7}=2.0\times10^6\ \text{m/s}=v$ ✓.
✏️ Example 2 — JEE level: an electron on a helix
An electron, accelerated from rest through $100\ \text{V}$, enters a uniform magnetic field of $1.0\ \text{mT}$ with its velocity at $60^\circ$ to the field. Find (a) its speed, (b) the radius of the helix, (c) its period and (d) the pitch of the helix.
Find the pitch in (d) before you open the solution:
(a) $\tfrac12mv^2=eV$: $v=\sqrt{\dfrac{2\times1.6\times10^{-19}\times100}{9.1\times10^{-31}}}=5.93\times10^6\ \text{m/s}$.
(b) $r=\dfrac{mv\sin60^\circ}{eB}=\dfrac{9.1\times10^{-31}\times5.93\times10^6\times0.866}{1.6\times10^{-19}\times1.0\times10^{-3}}=2.92\times10^{-2}\ \text{m}=2.92\ \text{cm}$.
(c) $T=\dfrac{2\pi m}{eB}=\dfrac{2\pi\times9.1\times10^{-31}}{1.6\times10^{-22}}=3.57\times10^{-8}\ \text{s}$.
(d) $p_\text{helix}=v\cos60^\circ\times T=2.97\times10^6\times3.57\times10^{-8}=0.106\ \text{m}=10.6\ \text{cm}$.
⏱ Shortcut $\dfrac{p_\text{helix}}{r}=\dfrac{2\pi\cos\theta}{\sin\theta}=\dfrac{2\pi}{\tan\theta}$: here $\dfrac{2\pi}{\sqrt3}=3.63$, and $3.63\times2.92=10.6\ \text{cm}$ ✓.
🚀 Beyond JEE Main — the cyclotron

The cyclotron is not named in the current JEE Main 2026, JEE Advanced or CBSE Class 12 syllabus lists; it is shown here because it is the classic use of the speed-independent period $T=2\pi m/qB$. Nothing in this box is needed for the exercises, the Exam corner or the quiz.

Two hollow D-shaped metal boxes ("dees") sit in a uniform field $B$ with a narrow gap between them. An alternating voltage across the gap accelerates an ion each time it crosses. Inside a dee there is no electric field and the ion moves on a semicircle — taking $T/2=\pi m/qB$ whatever its speed. So a voltage alternating at the fixed frequency $f=\dfrac{qB}{2\pi m}$ is always in step with the ion, which spirals outwards, gaining energy at every crossing. It leaves at the outer radius $R$ with $v=qBR/m$, i.e. kinetic energy $K=\dfrac{q^2B^2R^2}{2m}$ — for protons with $B=1.5\ \text{T}$ and $R=0.50\ \text{m}$, $f=22.9\ \text{MHz}$ and $K=4.31\times10^{-12}\ \text{J}=26.9\ \text{MeV}$. At speeds approaching that of light the mass effectively grows, the ions fall out of step, and this simple design stops working.

A proton and an α-particle ($m_\alpha\approx4m_p$, $q_\alpha=2e$) have the same kinetic energy and move at right angles to the same uniform magnetic field. The ratio of the radii of their paths $r_p:r_\alpha$ is

Combined electric and magnetic fields

When both fields are present the forces simply add, $\mathbf F=q\mathbf E+q\mathbf v\times\mathbf B$. The electric force depends only on where the particle is; the magnetic force depends on how fast it moves. That difference can be put to use.

Crossed fields. Let a positive particle move along $+x$ with speed $v$ through a region where $\mathbf B$ points into the page ($-z$) and $\mathbf E$ points down the page ($-y$), so that $\mathbf E$, $\mathbf B$ and $\mathbf v$ are mutually perpendicular. The magnetic force $q\mathbf v\times\mathbf B$ points up the page, with size $qvB$; the electric force points down, with size $qE$. They cancel exactly when $qE=qvB$:

$$v=\frac{E}{B}.$$

A particle with exactly this speed passes straight through, whatever its charge or mass, and whatever the sign of its charge (for a negative particle both forces reverse together). A faster particle is pushed to the magnetic side, a slower one to the electric side. A slit placed after the fields therefore lets through only particles with $v=E/B$: the arrangement is called a velocity selector.

📐 Result 13.10 — Velocity selector

In uniform, mutually perpendicular fields $\mathbf E$ and $\mathbf B$, a charged particle moving perpendicular to both, in the direction of $\mathbf E\times\mathbf B$, passes undeflected if and only if its speed is

$$v=\frac{E}{B},$$

independent of $q$ and $m$. (Gravity is neglected — it is about $10^{-11}$ of the electromagnetic forces for an ion.)

J. J. Thomson used crossed fields in 1897 to show that cathode rays are particles with a fixed charge-to-mass ratio — the discovery of the electron. In a mass spectrometer, ions leaving a velocity selector all have the same speed; they then enter a region with only a magnetic field $B'$, where $r=mv/qB'$, so ions of different mass land at different places. If instead $\mathbf E$ and $\mathbf B$ are parallel, the particle spirals round the field (from $\mathbf B$) while being accelerated along it (from $\mathbf E$): a helix whose pitch keeps growing.

✏️ Example 3 — Selecting a speed and sorting isotopes
Singly charged neon ions pass through a velocity selector with $E=1.5\times10^5\ \text{V/m}$ and $B=0.30\ \text{T}$, then enter a region with only a magnetic field $B'=0.50\ \text{T}$, perpendicular to their velocity, where they travel round a semicircle onto a photographic plate. (a) Find the speed of the ions that get through the selector. (b) Find the radii of the paths of $^{20}\text{Ne}^+$ and $^{22}\text{Ne}^+$ ions (masses $20\ \text{u}$ and $22\ \text{u}$, $1\ \text{u}=1.66\times10^{-27}\ \text{kg}$). (c) How far apart are the two lines on the plate?
(a) $v=\dfrac{E}{B}=\dfrac{1.5\times10^5}{0.30}=5.0\times10^5\ \text{m/s}$, for both isotopes.
(b) $r_{20}=\dfrac{20\times1.66\times10^{-27}\times5.0\times10^5}{1.6\times10^{-19}\times0.50}=0.2075\ \text{m}$; $r_{22}=\dfrac{22}{20}r_{20}=0.228\ \text{m}$.
(c) Each ion lands one diameter from the entry slit: separation $2(r_{22}-r_{20})=2\times0.0208=0.0415\ \text{m}=4.2\ \text{cm}$.
Why the selector? Without it, ions of slightly different speeds would land in a smear ($r\propto mv$) and the two isotopes could overlap. Fixing $v$ makes $r\propto m$ exactly.

In Interactive 1 choose a proton with $v=2.0\times10^6\ \text{m/s}$, $B=0.10\ \text{T}$ and $E=2.0\times10^5\ \text{V/m}$: it goes straight through. Now switch the particle to an α-particle with the same speed. What happens?

The readout $E/B=2\times10^6\ \text{m/s}$ equals $v$, so for any particle the electric force $qE$ and the magnetic force $qvB$ are equal and opposite — doubling $q$ doubles both, and the mass never enters the balance. Set $E=0$: the proton now circles with $r=20.9\ \text{cm}$ and the α-particle with $r=41.5\ \text{cm}$ (twice $m/q$); the antiproton circles the other way. Raise $v$ above $E/B$ with $E$ on and the particle bends up; lower it and it bends down.
Interactive 1 — A Charged Particle in Crossed E and B Fields

A particle enters from the left moving to the right. The magnetic field points into the page (⊗) everywhere; the plates make an electric field pointing down the page. The picture is drawn to scale ($60\ \text{cm}$ wide). Choose the particle, its speed and the two fields, then press Play to launch it. With $E=0$ you see a circle; with $E=vB$ a straight line.

2.0×10⁶ m/s0.10 T0
radius $mv/qB$—
period $2\pi m/qB$—
$E/B$—
$F_E/F_B$ at entry—

A beam of protons passes undeflected through a velocity selector. An electron beam with the same speed is sent through the same fields, in the same direction. The electrons

Force on a current-carrying conductor; parallel currents and the ampere

A wire carrying a current is full of moving charges, so in a magnetic field it feels the sum of the forces on them. Take a straight piece of wire of length $L$ and cross-sectional area $A$, with $n$ free charges $q$ per unit volume drifting with velocity $\mathbf v_d$. Each feels $q\mathbf v_d\times\mathbf B$; there are $nAL$ of them; and $nqAv_d=I$ (§ 12.1). The total force, passed on to the wire by collisions with its lattice, is $nAL\,q\,\mathbf v_d\times\mathbf B=I\,\mathbf L\times\mathbf B$, where $\mathbf L$ has length $L$ and points along the current.

📐 Result 13.11 — Force on a current-carrying conductor

A straight wire of length $L$ carrying current $I$ in a uniform magnetic field $\mathbf B$ feels the force

$$\mathbf F=I\,\mathbf L\times\mathbf B,\qquad F=ILB\sin\theta,$$

perpendicular to both the wire and the field ($\theta$ the angle between them). For a curved wire, $d\mathbf F=I\,d\mathbf l\times\mathbf B$ on each element; in a uniform field the total force on any wire running from point $P$ to point $Q$ equals the force on a straight wire from $P$ to $Q$ carrying the same current. Hence the net force on any closed loop in a uniform field is zero.

A handy way to get the direction is Fleming's left-hand rule: hold the thumb, first finger and second finger of the left hand at right angles; with the First finger along the Field and the seCond finger along the Current, the thuMb gives the Motion (force). It is just a memory aid for $I\,\mathbf L\times\mathbf B$.

✏️ Example 4 — Holding up a rod, and a bent wire
(a) A horizontal copper rod $0.50\ \text{m}$ long and of mass $60\ \text{g}$ lies at right angles to a horizontal uniform magnetic field of $0.30\ \text{T}$. What current in the rod lets the magnetic force support its weight? (b) A wire bent into a semicircle of radius $10\ \text{cm}$ carries $2.0\ \text{A}$ and lies in a plane perpendicular to a uniform field of $0.30\ \text{T}$. Find the net force on it. (c) The semicircle is closed by a straight wire along its diameter to make a loop. Find the net force on the loop.
(a) $ILB=mg$: $I=\dfrac{0.060\times9.8}{0.50\times0.30}=3.9\ \text{A}$, flowing in the direction for which $\mathbf L\times\mathbf B$ points upward.
(b) Replace the semicircle by its diameter, $2R=0.20\ \text{m}$: $F=I(2R)B=2.0\times0.20\times0.30=0.12\ \text{N}$, perpendicular to the diameter in the plane of the wire.
(c) The straight diameter carries the current the opposite way and feels $0.12\ \text{N}$ in the opposite direction: net force zero, as for every closed loop in a uniform field.
Check By direct integration, the components of $dF=IB\,dl$ along the diameter cancel in pairs and the perpendicular parts give $IBR\int_0^\pi\sin\phi\,d\phi=2IBR$ ✓.

Two parallel currents. Now we can put the two halves of the chapter together. A long straight wire carrying $I_1$ produces at distance $d$ a field $B_1=\dfrac{\mu_0I_1}{2\pi d}$ (Result 13.2), perpendicular to a second, parallel wire there. A length $L$ of the second wire, carrying $I_2$, therefore feels $F=I_2LB_1$. Working out the directions with the right-hand rules: if the currents are in the same direction the force on each wire points towards the other.

📐 Result 13.12 — Force between two long parallel currents

Two long straight parallel wires a distance $d$ apart, carrying currents $I_1$ and $I_2$, exert on each other a force per unit length

$$\frac{F}{L}=\frac{\mu_0I_1I_2}{2\pi d}.$$

Like (parallel) currents attract; unlike (antiparallel) currents repel — the opposite of the rule for charges. The forces on the two wires are equal and opposite, as Newton's third law requires.

📘 Definition 13.4 — The ampere

One ampere is the constant current which, flowing in two straight, parallel, infinitely long conductors of negligible cross-section placed $1\ \text{m}$ apart in vacuum, produces between them a force of $2\times10^{-7}\ \text{N}$ per metre of length.

(This definition, used from 1948 to 2019, is the one examined in JEE Main. Since 2019 the SI fixes instead the elementary charge, $e=1.602\,176\,634\times10^{-19}\ \text{C}$ exactly, and defines the ampere as one coulomb per second; $\mu_0$ is then measured, and equals $4\pi\times10^{-7}\ \text{T m/A}$ to better than one part in a billion, so the force law above still holds.)

✏️ Example 5 — JEE level: a square loop beside a long wire
A long straight wire carries $20\ \text{A}$. A square loop of side $10\ \text{cm}$ carrying $10\ \text{A}$ lies in the same plane, with its nearer side parallel to the wire and $5.0\ \text{cm}$ from it; the current in that nearer side is in the same direction as in the long wire. Find the net force on the loop and its direction.
Find the net force on the loop before you open the solution:
Near side Parallel current at $5.0\ \text{cm}$: attracted, $F_1=\dfrac{\mu_0I_1I_2a}{2\pi d}=\dfrac{2\times10^{-7}\times20\times10\times0.10}{0.050}=8.0\times10^{-5}\ \text{N}$ towards the wire.
Far side Antiparallel current at $15\ \text{cm}$: repelled, $F_2=\dfrac{2\times10^{-7}\times20\times10\times0.10}{0.15}=2.7\times10^{-5}\ \text{N}$ away from the wire.
Other sides The two sides perpendicular to the wire carry opposite currents through identical fields: equal and opposite forces, which cancel.
Net $F=8.0\times10^{-5}-2.67\times10^{-5}=5.3\times10^{-5}\ \text{N}$, towards the wire.
⏱ Shortcut $F=\dfrac{\mu_0I_1I_2a}{2\pi}\left(\dfrac1d-\dfrac1{d+a}\right)$. The field of the wire is not uniform, which is why a closed loop can feel a net force here.

A wire of any shape runs from point $P$ to point $Q$, $20\ \text{cm}$ apart, in a plane perpendicular to a uniform field of $0.50\ \text{T}$, and carries $3.0\ \text{A}$. The net magnetic force on it

Torque on a current loop and the moving-coil galvanometer

A closed loop in a uniform field feels no net force — but it does feel a torque. Take a rectangular coil of $N$ turns, sides $a$ and $b$, carrying current $I$, free to turn about an axis through its centre parallel to the sides of length $a$, in a uniform field $\mathbf B$ perpendicular to that axis. Let $\theta$ be the angle between $\mathbf B$ and the normal to the coil (the direction of the area vector $\mathbf A$, given by curling the right-hand fingers along the current). The two sides of length $a$ are always perpendicular to $\mathbf B$ and feel equal and opposite forces $NIaB$ — a couple. Their lines of action are separated by $b\sin\theta$, so the torque is $NIaB\cdot b\sin\theta$. The forces on the other two sides are along the axis and cancel without torque.

📐 Result 13.13 — Torque on a current loop

A plane coil of $N$ turns, each of area $A$, carrying current $I$ in a uniform magnetic field $\mathbf B$ feels zero net force and a torque

$$\tau=NIAB\sin\theta,\qquad\boldsymbol\tau=\mathbf m\times\mathbf B,\quad\mathbf m=NI\mathbf A,$$

where $\theta$ is the angle between the normal to the coil and $\mathbf B$. The result holds for a plane coil of any shape. The torque is largest, $NIAB$, when the plane of the coil is parallel to $\mathbf B$; it is zero when the plane is perpendicular to $\mathbf B$. The torque turns the coil so that $\mathbf m$ lines up with $\mathbf B$. ($\mathbf m$ is the coil's magnetic dipole moment — see § 13.3.)

The moving-coil galvanometer. This is the torque put to work as a current meter. A rectangular coil of many turns of fine insulated wire is wound on a light frame and pivoted (or hung from a phosphor-bronze strip) between the concave pole pieces of a strong permanent magnet. A soft-iron cylinder is fixed inside the coil. Together, the concave poles and the iron core make the field in the gap a radial magnetic field: whatever angle the coil turns through, its plane always lies along the field lines, so $\sin\theta=1$ and the deflecting torque is always $NIAB$. A spring (or the twisted suspension) supplies a restoring torque $k\phi$ proportional to the deflection $\phi$; $k$ is the torsional constant. The coil turns until the two balance:

$$NIAB=k\phi\qquad\Longrightarrow\qquad\phi=\left(\frac{NAB}{k}\right)I .$$

So the deflection is proportional to the current and the scale is linear — the reason for the radial field. (In a uniform field the torque would fall as $\cos\phi$ as the coil turned, and equal steps of current would give smaller and smaller steps of deflection: Interactive 2.) A pointer or a light beam reflected from a small mirror on the coil reads $\phi$.

📘 Definition 13.5 — Current and voltage sensitivity

The current sensitivity of a galvanometer is its deflection per unit current, and its voltage sensitivity is its deflection per unit potential difference across it ($V=IG$, where $G$ is the coil's resistance):

$$\frac{\phi}{I}=\frac{NAB}{k},\qquad\frac{\phi}{V}=\frac{NAB}{kG}.$$

Units: rad/A (or divisions per ampere) and rad/V. The current needed per division, $I/\phi=k/NAB$, is called the figure of merit.

Increasing $N$, $A$ or $B$, or using a weaker spring, makes the meter more sensitive. Note a subtle point JEE Main likes: doubling $N$ (with the same wire) doubles the current sensitivity, but it also doubles the length of wire and so $G$ — the voltage sensitivity is unchanged.

Ammeter. A galvanometer gives full-scale deflection for a small current $I_g$ (typically microamperes to milliamperes). To measure a larger current $I$, a small resistance $S$, the shunt, is connected in parallel with it, so that only $I_g$ goes through the coil and $I-I_g$ through the shunt. Same potential difference across both: $I_gG=(I-I_g)S$. The combination has a small resistance $\dfrac{GS}{G+S}$ and is connected in series in the circuit, where it hardly changes the current it measures.

Voltmeter. To measure a potential difference up to $V$, a large resistance $R$ is connected in series with the galvanometer, so that full-scale current $I_g$ flows when $V$ is applied: $V=I_g(G+R)$. The voltmeter is connected in parallel across the component; its large resistance $G+R$ means it draws little current and hardly disturbs the circuit.

📐 Result 13.14 — Converting a galvanometer

A galvanometer of resistance $G$ and full-scale current $I_g$ becomes

  • an ammeter of range $0$–$I$ with a shunt $\ S=\dfrac{I_gG}{I-I_g}\ $ in parallel (resistance of the ammeter $\dfrac{GS}{G+S}$, very small; ideal ammeter: zero);
  • a voltmeter of range $0$–$V$ with a resistance $\ R=\dfrac{V}{I_g}-G\ $ in series (resistance of the voltmeter $G+R=V/I_g$, very large; ideal voltmeter: infinite).
🧭 Problem-solving strategy — Meter conversions
  1. Find $I_g$ (full-scale current) and $G$; if you are given the full-scale voltage instead, $I_g=V_g/G$.
  2. Ammeter: the galvanometer and shunt share the same p.d., so currents divide inversely as resistances: $S=\dfrac{I_g}{I-I_g}G$. To multiply the range by $n$, $S=\dfrac{G}{n-1}$.
  3. Voltmeter: the series combination must take $I_g$ at the full voltage: $R=\dfrac{V}{I_g}-G$. To multiply a voltmeter's range by $n$, add $(n-1)$ times its resistance in series.
  4. Check: the ammeter's total resistance must come out smaller than $S$; the voltmeter's larger than $R$.
✏️ Example 6 — JEE level: building a meter
A galvanometer coil has $50$ turns, each $2.0\ \text{cm}\times2.5\ \text{cm}$, in a radial field of $0.40\ \text{T}$. The spring's restoring torque is $2.5\times10^{-7}\ \text{N m}$ per scale division, the scale has $30$ divisions and the coil's resistance is $40\ \Omega$. Find (a) the torque on the coil and the deflection for a current of $0.50\ \text{mA}$, (b) the current sensitivity, the full-scale current and the voltage sensitivity, (c) the shunt that turns it into an ammeter reading $0$–$1.5\ \text{A}$, and (d) the series resistance that turns it into a voltmeter reading $0$–$15\ \text{V}$.
Find the series resistance in (d) before you open the solution:
(a) $NAB=50\times5.0\times10^{-4}\times0.40=1.0\times10^{-2}\ \text{N m/A}$. At $0.50\ \text{mA}$: $\tau=5.0\times10^{-6}\ \text{N m}$; deflection $\dfrac{5.0\times10^{-6}}{2.5\times10^{-7}}=20$ divisions.
(b) Current sensitivity $\dfrac{NAB}{k}=\dfrac{1.0\times10^{-2}}{2.5\times10^{-7}}=4.0\times10^4\ \text{div/A}=40\ \text{div/mA}$. Full scale: $I_g=\dfrac{30}{40}=0.75\ \text{mA}$. Voltage sensitivity $\dfrac{40\ \text{div/mA}}{40\ \Omega}=1.0\ \text{div/mV}$ (full scale at $V_g=I_gG=30\ \text{mV}$).
(c) $S=\dfrac{I_gG}{I-I_g}=\dfrac{0.75\times10^{-3}\times40}{1.5-0.00075}=0.0200\ \Omega$, in parallel. The ammeter's resistance is $\dfrac{40\times0.0200}{40.02}=0.0200\ \Omega$.
(d) $R=\dfrac{V}{I_g}-G=\dfrac{15}{0.75\times10^{-3}}-40=19\,960\ \Omega$ in series (voltmeter resistance $20\ \text{k}\Omega$).
⏱ Shortcut A voltmeter's resistance is (range)/$I_g$: "$1333\ \Omega$ per volt" here. An ammeter's resistance is $V_g$/(range): $30\ \text{mV}/1.5\ \text{A}=0.020\ \Omega$.

In Interactive 2 choose the radial field and $k=5.0\times10^{-5}\ \text{N m/rad}$. At $I=2.5\ \text{mA}$ the coil turns through $28.6^\circ$. Predict the deflection at $I=5.0\ \text{mA}$ in the radial field — and then in a uniform field.

Radial field: $\phi=NABI/k=0.010\times0.0050/5.0\times10^{-5}=1.0\ \text{rad}$, and the readout shows $57.3^\circ$ — twice $28.6^\circ$, a linear scale (sensitivity $11.5^\circ$ per mA at every current). Uniform field: the magnetic torque falls to $NIAB\cos\phi$ as the coil turns, and the balance $NIAB\cos\phi=k\phi$ gives $42.3^\circ$ (sensitivity $8.47^\circ$ per mA, and falling). On the graph, the spring line $k\phi$ meets a flat line in the radial case but a falling cosine curve in the uniform case.
Interactive 2 — Inside a Moving-Coil Galvanometer

Looking down on the coil ($N=100$ turns of area $5.0\ \text{cm}^2$, $B=0.20\ \text{T}$): its two vertical sides carry current out of (⊙) and into (⊗) the page. Choose a radial field (concave poles and an iron core) or a uniform one (flat poles), set the current and the spring constant $k$, and press Play to switch the current on. The graph compares the magnetic torque with the spring's torque $k\phi$; the coil stops where they are equal.

2.5 mA5.0×10⁻⁵ N m/rad
magnetic torque—
deflection $\phi$—
$\phi/I$—
scale—
⚠️ JEE Main traps

1. Negative charges. $\mathbf F=q\mathbf v\times\mathbf B$ with $q\lt0$: an electron is pushed opposite to $\mathbf v\times\mathbf B$ and circles the other way. Use the right-hand rule, then reverse it.

2. Magnetic forces do no work. Speed and kinetic energy stay constant; the period $2\pi m/qB$ does not depend on the speed. Equal kinetic energies: $r\propto\sqrt m/q$; equal accelerating voltages: $r\propto\sqrt{m/q}$; equal speeds: $r\propto m/q$.

3. Which angle? In $\tau=NIAB\sin\theta$, $\theta$ is between $\mathbf B$ and the normal to the coil. "The plane of the coil makes $30^\circ$ with $\mathbf B$" means $\theta=60^\circ$. Torque is largest when the plane is parallel to $\mathbf B$.

4. Parallel currents attract. Like currents attract and unlike repel — the reverse of charges. The net force on a closed loop is zero only in a uniform field.

5. Shunt versus series. Ammeter: small shunt in parallel, meter in series with the circuit. Voltmeter: large resistance in series with the coil, meter in parallel with the component. Mixing them up is the commonest wrong option.

To convert a galvanometer into an ammeter of larger range, we should connect

Exercises

Take $e=1.6\times10^{-19}\ \text{C}$, $m_p=1.67\times10^{-27}\ \text{kg}$, $m_e=9.1\times10^{-31}\ \text{kg}$, the mass of an α-particle $6.64\times10^{-27}\ \text{kg}$ (charge $2e$), $\mu_0=4\pi\times10^{-7}\ \text{T m/A}$ and $g=9.8\ \text{m/s}^2$ unless told otherwise.

I
Charged particles in a magnetic field.
  • 1 Find the force on an electron moving at $3.0\times10^6\ \text{m/s}$ at $30^\circ$ to a field of $0.20\ \text{T}$.
  • 2 Find the radius of the path of an α-particle moving at $1.0\times10^6\ \text{m/s}$ perpendicular to a field of $0.50\ \text{T}$.
  • 3 Find the period of revolution of an electron in a field of $1.0\ \text{mT}$. Does it depend on the electron's speed?
  • 4 A proton of kinetic energy $2.0\ \text{MeV}$ moves perpendicular to a field of $0.50\ \text{T}$. Find the radius of its path.
  • 5 A deuteron ($m=2m_p$, charge $e$) and a proton have the same kinetic energy and move perpendicular to the same field. Find the ratio of their radii $r_d/r_p$.
  • 6 A proton enters a field of $0.10\ \text{T}$ with speed $4.0\times10^5\ \text{m/s}$ at $37^\circ$ to the field. Find the radius and the pitch of its helix ($\sin37^\circ=0.6$, $\cos37^\circ=0.8$).
  • 7 A proton moving at $2.0\times10^6\ \text{m/s}$ enters, at right angles, a region $10\ \text{cm}$ wide containing a field of $0.10\ \text{T}$ parallel to the region's edges. Through what angle is it deflected when it leaves?
  • 8 What is the least field that would stop the proton of part 7 from crossing the region (turning it back)?
1 $F=evB\sin30^\circ=1.6\times10^{-19}\times3.0\times10^6\times0.20\times0.5=4.8\times10^{-14}\ \text{N}$.
2 $r=\dfrac{mv}{qB}=\dfrac{6.64\times10^{-27}\times1.0\times10^6}{3.2\times10^{-19}\times0.50}=0.0415\ \text{m}=4.15\ \text{cm}$.
3 $T=\dfrac{2\pi m}{eB}=\dfrac{2\pi\times9.1\times10^{-31}}{1.6\times10^{-22}}=3.57\times10^{-8}\ \text{s}$ — independent of the speed (while $v\ll c$).
4 $K=3.2\times10^{-13}\ \text{J}$; $p=\sqrt{2mK}=3.27\times10^{-20}\ \text{kg m/s}$; $r=\dfrac{p}{eB}=\dfrac{3.27\times10^{-20}}{0.80\times10^{-19}}=0.409\ \text{m}$.
5 $r=\sqrt{2mK}/qB\propto\sqrt m$ at equal $q$: $r_d/r_p=\sqrt2=1.41$.
6 $r=\dfrac{mv\sin37^\circ}{eB}=\dfrac{1.67\times10^{-27}\times4.0\times10^5\times0.6}{1.6\times10^{-20}}=0.0251\ \text{m}$; pitch $=\dfrac{2\pi mv\cos37^\circ}{eB}=0.210\ \text{m}$.
7 $r=\dfrac{mv}{eB}=0.209\ \text{m}$. The proton moves on an arc that starts perpendicular to the edge; it leaves after rising a horizontal distance $d=r\sin\delta$: $\sin\delta=\dfrac{0.10}{0.209}=0.479$, $\delta=28.6^\circ$.
8 It turns back if $r\le d$: $B\ge\dfrac{mv}{ed}=\dfrac{1.67\times10^{-27}\times2.0\times10^6}{1.6\times10^{-19}\times0.10}=0.209\ \text{T}$.
II
Crossed fields and forces on conductors.
  • 1 Crossed fields $E=6.0\times10^4\ \text{V/m}$ and $B=0.040\ \text{T}$ form a velocity selector. Find the speed of the particles that pass undeflected.
  • 2 When the electric field of part 1 is switched off, the undeflected particles move in a circle of radius $39\ \text{cm}$. Find their charge-to-mass ratio and suggest what they are.
  • 3 Find the force on a straight wire $0.60\ \text{m}$ long carrying $5.0\ \text{A}$ at $30^\circ$ to a uniform field of $0.20\ \text{T}$.
  • 4 A wire bent into an L, with arms $30\ \text{cm}$ and $40\ \text{cm}$, carries $2.0\ \text{A}$ in a uniform field of $0.50\ \text{T}$ perpendicular to its plane. Find the net force on it.
  • 5 A rod of mass $20\ \text{g}$ and length $40\ \text{cm}$ hangs horizontally from two light threads in a horizontal field of $0.25\ \text{T}$ perpendicular to it. What current makes the tension in the threads zero?
  • 6 A rod of mass $0.10\ \text{kg}$ rests across two smooth rails $0.50\ \text{m}$ apart in a plane inclined at $30^\circ$ to the horizontal. A vertical field of $0.40\ \text{T}$ acts. What current in the rod keeps it at rest?
  • 7 Explain why a rigid closed loop of any shape carrying a current in a uniform field does not accelerate, and say what it can do instead.
  • 8 Electrons pass undeflected through crossed fields $E=2000\ \text{V/m}$ and $B=1.0\ \text{mT}$. Find their speed and their kinetic energy in eV.
1 $v=\dfrac{E}{B}=\dfrac{6.0\times10^4}{0.040}=1.5\times10^6\ \text{m/s}$.
2 $\dfrac{q}{m}=\dfrac{v}{rB}=\dfrac{1.5\times10^6}{0.39\times0.040}=9.6\times10^7\ \text{C/kg}$ — that of the proton ($e/m_p=9.58\times10^7\ \text{C/kg}$).
3 $F=ILB\sin30^\circ=5.0\times0.60\times0.20\times0.5=0.30\ \text{N}$.
4 The ends are $\sqrt{0.30^2+0.40^2}=0.50\ \text{m}$ apart: $F=2.0\times0.50\times0.50=0.50\ \text{N}$, perpendicular to the line joining the ends.
5 $ILB=mg$: $I=\dfrac{0.020\times9.8}{0.40\times0.25}=1.96\ \text{A}$, in the direction giving an upward force.
6 The force $ILB$ is horizontal (perpendicular to the rod and to the vertical field). Along the incline: $ILB\cos30^\circ=mg\sin30^\circ$, so $I=\dfrac{mg\tan30^\circ}{LB}=\dfrac{0.10\times9.8\times0.577}{0.50\times0.40}=2.83\ \text{A}$.
7 The force on the loop equals the force on a straight wire from its starting point to its end point — the same point — so it is zero. It can still feel a torque $\mathbf m\times\mathbf B$ and turn.
8 $v=\dfrac{E}{B}=2.0\times10^6\ \text{m/s}$; $K=\tfrac12mv^2=\tfrac12\times9.1\times10^{-31}\times4.0\times10^{12}=1.82\times10^{-18}\ \text{J}=11.4\ \text{eV}$.
III
Parallel currents and torque on a coil.
  • 1 Two long parallel wires $5.0\ \text{cm}$ apart carry $10\ \text{A}$ and $15\ \text{A}$. Find the force per metre between them.
  • 2 Two long parallel wires $2.0\ \text{cm}$ apart carry equal currents and repel each other with $8.0\times10^{-5}\ \text{N}$ per metre. Find the current and say how the currents are directed.
  • 3 Three long parallel wires lie in a plane, $10\ \text{cm}$ apart, each carrying $10\ \text{A}$ in the same direction. Find the force per metre on the middle wire and on an outer wire.
  • 4 A long horizontal wire carrying $60\ \text{A}$ is fixed. A second wire of mass $1.0\ \text{g}$ per metre floats in equilibrium $1.0\ \text{cm}$ directly above it. Find the current in the upper wire and its direction.
  • 5 A rectangular coil of $20$ turns, $8.0\ \text{cm}\times5.0\ \text{cm}$, carries $1.5\ \text{A}$ in a field of $0.50\ \text{T}$. The normal to the coil makes $30^\circ$ with the field. Find the torque.
  • 6 Find the largest torque on the coil of part 5 and the orientation in which it occurs.
  • 7 A circular coil of $50$ turns and radius $5.0\ \text{cm}$ carries $2.0\ \text{A}$ with its plane parallel to a field of $0.20\ \text{T}$. Find the torque.
  • 8 A given length of wire carrying a fixed current can be bent into a one-turn circle or a one-turn square. Find the ratio of the largest torques in the same field, circle : square.
1 $\dfrac{F}{L}=\dfrac{2\times10^{-7}\times10\times15}{0.050}=6.0\times10^{-4}\ \text{N/m}$.
2 $I^2=\dfrac{8.0\times10^{-5}\times0.020}{2\times10^{-7}}=8.0$, $I=2.83\ \text{A}$; they repel, so the currents are opposite.
3 Middle wire: equal pulls either way, zero. Outer wire: $2\times10^{-7}\times100\left(\dfrac{1}{0.10}+\dfrac{1}{0.20}\right)=3.0\times10^{-4}\ \text{N/m}$, towards the middle.
4 The upper wire must be repelled, so its current is opposite: $\dfrac{\mu_0I_1I_2}{2\pi d}=\lambda g$, $I_2=\dfrac{1.0\times10^{-3}\times9.8\times0.010}{2\times10^{-7}\times60}=8.17\ \text{A}$.
5 $\tau=NIAB\sin30^\circ=20\times1.5\times4.0\times10^{-3}\times0.50\times0.5=0.030\ \text{N m}$.
6 $\tau_\text{max}=NIAB=0.060\ \text{N m}$, when the plane of the coil is parallel to the field ($\theta=90^\circ$).
7 Plane parallel to $\mathbf B$: $\tau=NI\pi r^2B=50\times2.0\times\pi\times0.0025\times0.20=0.157\ \text{N m}$.
8 For length $\ell$: circle $A=\dfrac{\ell^2}{4\pi}$, square $A=\dfrac{\ell^2}{16}$. Ratio $\dfrac{16}{4\pi}=\dfrac4\pi=1.27$ — of all shapes, the circle encloses the most area.
IV
Galvanometers, ammeters and voltmeters.
  • 1 A galvanometer coil has $100$ turns of area $4.0\ \text{cm}^2$ in a radial field of $0.25\ \text{T}$, and the spring constant is $5.0\times10^{-6}\ \text{N m}$ per degree. Find its current sensitivity in degrees per mA.
  • 2 A galvanometer of resistance $60\ \Omega$ gives full-scale deflection for $5.0\ \text{mA}$. Find the shunt needed to make it an ammeter of range $0$–$1.0\ \text{A}$.
  • 3 Find the series resistance that makes the galvanometer of part 2 a voltmeter of range $0$–$3.0\ \text{V}$.
  • 4 Find the resistance of the ammeter of part 2.
  • 5 A galvanometer reads up to $10\ \text{mA}$. A shunt of resistance $G/99$ is connected across it. Find the new range, in amperes.
  • 6 A voltmeter of range $0$–$5.0\ \text{V}$ has resistance $5.0\ \text{k}\Omega$. How would you make it read up to $20\ \text{V}$?
  • 7 The number of turns of a galvanometer coil is doubled, keeping the same wire and the same coil size. What happens to its current sensitivity, its resistance and its voltage sensitivity?
  • 8 Two $1000\ \Omega$ resistors in series are connected to an ideal $6.0\ \text{V}$ cell. A voltmeter of resistance $1000\ \Omega$ is connected across one of them. What does it read? Comment.
1 $\dfrac{\phi}{I}=\dfrac{NAB}{k}=\dfrac{100\times4.0\times10^{-4}\times0.25}{5.0\times10^{-6}}=2000^\circ/\text{A}=2.0^\circ$ per mA.
2 $S=\dfrac{I_gG}{I-I_g}=\dfrac{5.0\times10^{-3}\times60}{0.995}=0.302\ \Omega$ in parallel.
3 $R=\dfrac{3.0}{5.0\times10^{-3}}-60=540\ \Omega$ in series.
4 $\dfrac{GS}{G+S}=\dfrac{60\times0.302}{60.302}=0.300\ \Omega$ (equivalently $V_g/I=0.30\ \text{V}/1.0\ \text{A}$).
5 With $S=G/99$ the shunt carries $99$ times the coil current: range $100\times10\ \text{mA}=1.0\ \text{A}$.
6 The range must be multiplied by $4$: add $(4-1)\times5.0=15\ \text{k}\Omega$ in series.
7 Current sensitivity $NAB/k$ doubles; the wire is twice as long, so $G$ doubles; the voltage sensitivity $NAB/kG$ is unchanged.
8 $1000\ \Omega\parallel1000\ \Omega=500\ \Omega$; the voltmeter reads $6.0\times\dfrac{500}{1500}=2.0\ \text{V}$ instead of the true $3.0\ \text{V}$. A voltmeter must have a resistance much larger than the resistance it is connected across.
🎯 Exam corner JEE Main · MCQJEE Main · Numerical

E1. JEE Main · MCQ A proton and an α-particle, starting from rest, are accelerated through the same potential difference and then enter a uniform magnetic field at right angles to it. The ratio of the radii of their circular paths, $r_p:r_\alpha$, is (A) $1:1$ (B) $1:\sqrt2$ (C) $\sqrt2:1$ (D) $1:2$

Radius $K=qV$, so $r=\dfrac{\sqrt{2mqV}}{qB}=\dfrac1B\sqrt{\dfrac{2mV}{q}}\propto\sqrt{\dfrac mq}$.
Ratio $\dfrac{r_p}{r_\alpha}=\sqrt{\dfrac{m}{e}\cdot\dfrac{2e}{4m}}=\dfrac{1}{\sqrt2}$.
Answer (B) $1:\sqrt2$.
⏱ Shortcut Same voltage: $r\propto\sqrt{m/q}$. Same kinetic energy: $r\propto\sqrt m/q$ (answer would be (A)). Same speed: $r\propto m/q$ (answer (D)).

E2. JEE Main · Numerical A particle of specific charge $q/m=1.0\times10^8\ \text{C/kg}$ enters a uniform magnetic field of $0.20\ \text{T}$ with speed $4.0\times10^6\ \text{m/s}$ at $60^\circ$ to the field. Find the pitch of its helical path in cm (take $\pi=3.14$). Give the answer to the nearest integer.

Period $T=\dfrac{2\pi m}{qB}=\dfrac{2\times3.14}{1.0\times10^8\times0.20}=3.14\times10^{-7}\ \text{s}$.
Pitch $v\cos60^\circ\times T=2.0\times10^6\times3.14\times10^{-7}=0.628\ \text{m}=62.8\ \text{cm}$.
Answer $63$.
⏱ Shortcut Using $\sin60^\circ$ instead of $\cos60^\circ$ gives $109$ — the pitch uses the component along $\mathbf B$.

E3. JEE Main · MCQ Two long parallel wires exert a force $F$ per unit length on each other. If the current in each wire is doubled and the distance between them is halved, the force per unit length becomes (A) $2F$ (B) $4F$ (C) $F$ (D) $8F$

Scaling $\dfrac FL=\dfrac{\mu_0I_1I_2}{2\pi d}$: $I_1I_2\to4I_1I_2$ and $\dfrac1d\to\dfrac2d$.
Result $4\times2=8$.
Answer (D) $8F$.
⏱ Shortcut Force $\propto I_1I_2/d$ — not $1/d^2$, since the field of a long wire falls as $1/d$.

E4. JEE Main · Numerical A galvanometer of resistance $100\ \Omega$ gives full-scale deflection for a current of $1.0\ \text{mA}$. What resistance, in ohms, must be connected in series with it to make a voltmeter of range $0$–$10\ \text{V}$? Give the answer to the nearest integer.

Total The voltmeter must have $\dfrac{V}{I_g}=\dfrac{10}{1.0\times10^{-3}}=10\,000\ \Omega$.
Series $R=10\,000-100=9900\ \Omega$.
Answer $9900$.
⏱ Shortcut $10\,000$ is the trap — the coil's own $100\ \Omega$ is already part of the total.

E5. JEE Main · Numerical A circular coil of $50$ turns and radius $10\ \text{cm}$ carries $3.0\ \text{A}$ in a uniform field of $0.40\ \text{T}$. The plane of the coil makes an angle of $60^\circ$ with the field. The torque on the coil is $x\times10^{-2}\ \text{N m}$. Find $x$ (take $\pi=3.14$). Give the answer to the nearest integer.

Angle The plane is at $60^\circ$ to $\mathbf B$, so the normal is at $\theta=30^\circ$.
Torque $\tau=NIAB\sin30^\circ=50\times3.0\times3.14\times0.010\times0.40\times0.5=0.942\ \text{N m}=94.2\times10^{-2}\ \text{N m}$.
Answer $94$.
⏱ Shortcut Using $\sin60^\circ$ gives $163$ — the commonest slip. Plane at $\alpha$ to $\mathbf B$: $\tau=NIAB\cos\alpha$.

E6. JEE Main · MCQ A beam containing protons, deuterons and α-particles with a wide range of speeds is sent through crossed fields $E=4.0\times10^4\ \text{V/m}$ and $B=0.020\ \text{T}$, perpendicular to both. The particles that emerge undeflected are (A) particles of all three kinds, each with speed $2.0\times10^6\ \text{m/s}$ (B) only protons, with speed $2.0\times10^6\ \text{m/s}$ (C) only α-particles, with speed $1.0\times10^6\ \text{m/s}$ (D) particles of all three kinds, each with speed $8.0\times10^2\ \text{m/s}$

Balance $qE=qvB$ gives $v=E/B$ — no $q$, no $m$.
Speed $v=\dfrac{4.0\times10^4}{0.020}=2.0\times10^6\ \text{m/s}$.
Answer (A).
⏱ Shortcut (D) is $E\times B$ instead of $E/B$. A velocity selector cannot sort by $q/m$ — that needs a separate magnetic field afterwards.
🔬 Research–Teaching NexusResearch-tutored · optional, about 60 minutes

Research question. Can a kitchen scale, a magnet and a battery measure the force $F=ILB$ on a wire well enough to find the field of the magnet — and how close does this come to the way the kilogram is now realised?

Why it matters. Since 2019 the kilogram has been defined through Planck's constant, and national laboratories in the UK, USA, Canada, France, China and elsewhere realise it with a Kibble balance: the weight of a mass is balanced by the magnetic force on a current-carrying coil, $mg=ILB$, and $LB$ is found in a second, moving-coil measurement. The same force drives loudspeakers, hard-disk read heads and electric vehicles. A simple "current balance" shows the principle — and its limits.

What to do.

  1. Place a strong flat magnet (or a stack) on a digital kitchen scale reading to $0.01\ \text{g}$, and tare the scale.
  2. Fix a straight stiff wire horizontally just above the magnet's face, held by a clamp that does not touch the scale. Connect it through an ammeter, a rheostat and a switch to a battery or bench supply.
  3. Pass currents of $0.5$ to $3\ \text{A}$ (briefly, so the wire does not heat). By Newton's third law the wire pushes the magnet down (or pulls it up); record the scale reading $\Delta m$ for each current and both directions.
  4. Plot $\Delta m\,g$ against $I$. From the slope and the length of wire directly over the magnet, estimate $B$.
  5. Check $B$ independently with a phone magnetometer held at the same height. Try a wire at $45^\circ$ to the magnet's edge: does the force follow $\sin\theta$?

Tools: Digital scale ($0.01\ \text{g}$), neodymium magnet(s), stiff copper wire, clamp stand, battery or bench power supply, ammeter, rheostat, phone magnetometer app, spreadsheet.

Hand in: The graph of force against current with its slope and uncertainty, your value of $B$ compared with the magnetometer reading, and a short paragraph on why a Kibble balance measures $LB$ by moving the coil instead of by measuring $L$ and $B$ separately.

Going further. Replace the straight wire with a small rectangular coil hung on a thread above the magnet and observe the torque. How does the twist depend on the current and on the coil's orientation?

Instructor note: typical results are $10$–$50\ \text{mg}$ changes per ampere for a few centimetres of wire over a neodymium magnet, giving $B\approx0.1$–$0.3\ \text{T}$ near the surface. The field is not uniform over the wire, so "effective length × average field" is what is really measured — an excellent way to introduce the Kibble balance's trick. Warn students that neodymium magnets snap together and that thin wires get hot at a few amperes.

🧪 Self-check quiz

0/5 correct

Q1. The work done by a uniform magnetic field on a charged particle moving in it, during one full revolution, is

Q2. The period of revolution of a charged particle moving perpendicular to a uniform magnetic field does not depend on

Q3. An ammeter must

Q4. A current-carrying coil in a uniform magnetic field experiences the largest torque when

Q5. Two long parallel wires carry currents in the same direction. The wires