5.4 Rigid-Body Rotation and Equations of Rotational Motion
A rigid body turning about a fixed axis obeys laws that mirror straight-line motion term by term: $\omega=\omega_0+\alpha t$ for kinematics, $\tau=I\alpha$ for dynamics, $\tfrac12I\omega^2$ for energy and $P=\tau\omega$ for power. Learn the dictionary once and every pulley, flywheel and hinged-rod problem becomes a familiar one.
A ceiling fan is switched off and keeps turning for half a minute; a bucket drops into a well, spinning the winch drum faster and faster; a flywheel in a press stores energy between strokes; a door swings shut on its hinges. Each is a rigid body rotating about a fixed axis, and each raises the questions we asked of a car on a straight road in Chapter 2 and Chapter 3: how far, how fast, what force (here, what torque) makes it speed up, how much energy it carries, and how much power is needed.
The pleasant surprise is that the answers have exactly the same form as for straight-line motion. Angle takes the place of distance, angular velocity of velocity, torque of force and moment of inertia (Section 5.3) of mass. In this section we develop the kinematics of rotation with constant angular acceleration, the dynamical law $\tau=I\alpha$, the rotational kinetic energy, work and power, and finish with a full side-by-side comparison of linear and rotational motion. We use torque and angular momentum from Section 5.2 and angular velocity and acceleration from Section 2.4.
Kinematics of rotation about a fixed axis
In a rigid body the distance between any two particles never changes. If the body turns about a fixed axis, every particle moves on a circle centred on the axis, in a plane perpendicular to it, and in any time interval every particle turns through the same angle. So one number — the angle $\theta$ turned by any line in the body perpendicular to the axis — describes the position of the whole body.
For a rigid body turning about a fixed axis, the angular position $\theta$ (in radians) is the angle between a reference line fixed in the body and a fixed direction in space, both perpendicular to the axis. The body's angular velocity and angular acceleration are
$$\omega=\frac{d\theta}{dt},\qquad \alpha=\frac{d\omega}{dt}=\frac{d^2\theta}{dt^2} .$$They are the same for every particle of the body. As vectors, $\boldsymbol\omega$ and $\boldsymbol\alpha$ point along the axis, with the direction of $\boldsymbol\omega$ given by the right-hand rule (curl the fingers the way the body turns; the thumb points along $\boldsymbol\omega$).
A particle at perpendicular distance $r$ from the axis moves along an arc $s=r\theta$, so its speed is $v=r\omega$. Its acceleration has two parts: a tangential part $a_t=r\alpha$ (changing the speed) and a centripetal part $a_c=\omega^2r=v^2/r$ (changing the direction), directed towards the axis. The total is $a=\sqrt{a_t^2+a_c^2}$. These links between linear and angular quantities hold only with angles in radians; convert revolutions with $1\ \text{rev}=2\pi\ \text{rad}$ and $n$ revolutions per minute with $\omega=\dfrac{2\pi n}{60}\ \text{rad/s}$.
When the angular acceleration is constant, $\omega$ grows linearly in time exactly as $v$ does for constant $a$, and integrating once more gives $\theta$. The algebra is the same as in Section 2.1 with $x\to\theta$, $v\to\omega$, $a\to\alpha$.
For rotation about a fixed axis with constant angular acceleration $\alpha$, starting with angular velocity $\omega_0$ at $t=0$ and $\theta$ measured from the starting position:
$$\omega=\omega_0+\alpha t,\qquad \theta=\omega_0t+\tfrac12\alpha t^2,$$ $$\omega^2=\omega_0^2+2\alpha\theta,\qquad \theta=\tfrac12(\omega_0+\omega)\,t .$$Angles in radians; $\alpha$ is negative when the body slows down. If $\alpha$ is not constant, use $\omega=d\theta/dt$ and $\alpha=d\omega/dt$ directly (and $\alpha=\omega\,d\omega/d\theta$).
A wheel starts from rest with constant angular acceleration. It turns through $\theta_1$ in the first $2\ \text{s}$ and $\theta_2$ in the next $2\ \text{s}$. The ratio $\theta_2/\theta_1$ is
Dynamics of rotation: $\tau=I\alpha$
What makes a body's rotation speed up? Not force alone — a large force through the axis does nothing — but torque about the axis. Consider a particle $m_i$ of a rigid body at distance $r_i$ from the fixed axis. Only the tangential component $F_{i,t}$ of the total force on it changes its speed: $F_{i,t}=m_ia_{i,t}=m_ir_i\alpha$. Multiply by $r_i$ to get the torque of that force about the axis: $\tau_i=r_iF_{i,t}=m_ir_i^2\alpha$. Now add over all particles. The internal forces between particles come in equal and opposite pairs along the line joining them (Newton's third law), so their torques cancel in pairs, and only the torques of the external forces survive:
$$\tau_\text{ext}=\Big(\sum m_ir_i^2\Big)\alpha=I\alpha .$$For a rigid body rotating about a fixed axis, the sum of the torques of the external forces about that axis equals the moment of inertia about the same axis times the angular acceleration:
$$\tau_\text{ext}=I\alpha .$$Equivalently $\tau_\text{ext}=\dfrac{dL}{dt}$ with $L=I\omega$. Conditions: the body is rigid; $\tau$ and $I$ are taken about the same axis; that axis is fixed (or is an axis through the centre of mass that keeps its direction). Torques that turn the body in the chosen positive sense count positive, the others negative. If $\tau_\text{ext}=0$, then $\alpha=0$ and $\omega$ stays constant.
This is the exact counterpart of $F=ma$: for the same torque, a body with a larger moment of inertia gets a smaller angular acceleration. A ring and a disc of the same mass and radius, given the same torque, do not speed up equally — the disc gains angular velocity twice as fast.
- Draw a free-body diagram for each body: forces on every block, torques on every pulley or drum. Choose consistent positive directions (if the block moves down, the pulley turns so that its rim moves the same way).
- Write $F=ma$ for each block and $\tau=I\alpha$ for each rotating body about its fixed axis. A string that leaves a pulley of radius $R$ exerts torque $TR$.
- Write the constraint: if the string does not slip on the pulley, the rim's tangential acceleration equals the string's acceleration, $a=R\alpha$.
- Solve. A massive pulley has different tensions on its two sides — it is their difference that turns it. Check the limit $I\to0$, which must give the light-pulley answer of Section 3.2.
Set the hanging mass to $m=1.0\ \text{kg}$ and choose a disc pulley of mass $M=2.0\ \text{kg}$. What acceleration does the block have?
A thin ring and a uniform disc have the same mass and radius and turn freely on fixed axles through their centres. The same tangential force is applied at the rim of each. The ratio $\alpha_\text{disc}/\alpha_\text{ring}$ is
Rotational kinetic energy, work and power
In Section 5.3 we found that a rigid body turning with angular velocity $\omega$ about a fixed axis has kinetic energy $K=\tfrac12\big(\sum m_ir_i^2\big)\omega^2=\tfrac12I\omega^2$. Now ask how a torque changes that energy. A force with tangential component $F_t$ acting at distance $r$ from the axis moves its point of application through an arc $ds=r\,d\theta$ as the body turns through $d\theta$, so it does work $dW=F_t\,r\,d\theta=\tau\,d\theta$.
When a body turns about a fixed axis through $d\theta$ under a torque $\tau$ about that axis, the torque does work $dW=\tau\,d\theta$. Over a finite rotation, and for a constant torque,
$$W=\int_{\theta_1}^{\theta_2}\tau\,d\theta,\qquad W=\tau\,\Delta\theta\ \ (\tau\ \text{constant}).$$The power delivered by the torque is the rate of doing work: $P=\dfrac{dW}{dt}=\tau\omega$. Angles in radians; $W$ in joules, $P$ in watts.
A rigid body turning about a fixed axis has kinetic energy
$$K_\text{rot}=\tfrac12I\omega^2=\frac{L^2}{2I}\qquad(L=I\omega).$$The total work done by all the torques acting on it equals the change in its rotational kinetic energy:
$$W_\text{net}=\int\tau_\text{net}\,d\theta=\tfrac12I\omega_2^2-\tfrac12I\omega_1^2 .$$If only conservative forces (such as gravity) do work, mechanical energy is conserved: $K_\text{rot}+U$ is constant, and for linked systems the kinetic energies of all moving parts — translating and rotating — must be included.
Proof of the theorem. Using $\tau=I\alpha$ and $\alpha=\dfrac{d\omega}{dt}=\dfrac{d\omega}{d\theta}\dfrac{d\theta}{dt}=\omega\dfrac{d\omega}{d\theta}$, we get $\tau\,d\theta=I\omega\,d\omega$, and integrating gives $\int\tau\,d\theta=\tfrac12I\omega_2^2-\tfrac12I\omega_1^2$. It is the same argument that turns $F=ma$ into the work–energy theorem of Chapter 4.
Energy methods shine when the torque changes during the motion. The torque of gravity on the hinged rod of Example 4 falls from $MgL/2$ to zero as the rod swings down, so $\alpha$ is not constant and the kinematic equations do not apply — but energy conservation still gives the angular velocity at once.
Use the widget's starting settings: motor torque $\tau=10\ \text{N m}$ for $5\ \text{s}$, friction torque $\tau_f=2\ \text{N m}$, $I=2.0\ \text{kg m}^2$. After the motor is switched off, how long does the flywheel coast before it stops?
A constant torque acts on a wheel that starts from rest on a frictionless axle. The power delivered to the wheel
Comparison of linear and rotational motion
Every result of this section has a twin in straight-line motion. The table is worth learning as a dictionary: if you can solve a problem for a block, you can solve its rotational twin by translating each symbol.
| Straight-line motion | Rotation about a fixed axis |
|---|---|
| displacement $x$ | angular displacement $\theta$ (rad) |
| velocity $v=\dfrac{dx}{dt}$ | angular velocity $\omega=\dfrac{d\theta}{dt}$ |
| acceleration $a=\dfrac{dv}{dt}$ | angular acceleration $\alpha=\dfrac{d\omega}{dt}$ |
| mass $m$ (fixed for the body) | moment of inertia $I=\sum m_ir_i^2$ (depends on the axis) |
| force $F$ | torque $\tau=rF_t$ |
| $F=ma$ | $\tau=I\alpha$ |
| momentum $p=mv$; $F=\dfrac{dp}{dt}$ | angular momentum $L=I\omega$; $\tau=\dfrac{dL}{dt}$ |
| impulse $F\Delta t=\Delta p$ | angular impulse $\tau\Delta t=\Delta L$ |
| $v=u+at$, $\ x=ut+\tfrac12at^2$, $\ v^2=u^2+2ax$ | $\omega=\omega_0+\alpha t$, $\ \theta=\omega_0t+\tfrac12\alpha t^2$, $\ \omega^2=\omega_0^2+2\alpha\theta$ |
| kinetic energy $\tfrac12mv^2=\dfrac{p^2}{2m}$ | kinetic energy $\tfrac12I\omega^2=\dfrac{L^2}{2I}$ |
| work $W=\int F\,dx$ | work $W=\int\tau\,d\theta$ |
| power $P=Fv$ | power $P=\tau\omega$ |
| equilibrium: $\sum F=0$ | equilibrium: $\sum\tau=0$ |
The links between the two columns for a point at distance $r$ from the axis are $s=r\theta$, $v=r\omega$ and $a_t=r\alpha$. One important difference: a body's mass is the same whichever way it moves, but its moment of inertia depends on the axis chosen, so in rotational problems you must always state the axis — for $I$, for $\tau$ and for $L$, and the same axis for all three.
Rolling motion is not in the JEE Main 2026 syllabus list (it is listed for JEE Advanced 2026). This box is for interest only; nothing here is used in the exercises, the Exam corner or the quiz.
A wheel rolling without slipping on the ground combines translation of its centre with rotation about the centre, linked by $v_\text{cm}=\omega R$: the contact point is momentarily at rest. Its kinetic energy is the sum of the two parts,
$$K=\tfrac12Mv_\text{cm}^2+\tfrac12I_\text{cm}\omega^2=\tfrac12Mv_\text{cm}^2\Big(1+\frac{k^2}{R^2}\Big).$$Rolling from rest down an incline of angle $\theta$, a body therefore has $a=\dfrac{g\sin\theta}{1+k^2/R^2}$: a solid sphere ($k^2/R^2=\tfrac25$) beats a disc ($\tfrac12$), which beats a ring ($1$), whatever their masses and sizes. Static friction at the contact supplies the torque but, because the contact point does not slip, does no work.
1. Equal tensions round a heavy pulley. If the pulley has mass, $T_1\ne T_2$; their difference times $R$ is what gives it angular acceleration. "$T=mg$" for a hanging block that is accelerating is wrong whether or not the pulley is light.
2. Forgetting radians. $v=r\omega$, $a_t=r\alpha$, $W=\tau\theta$ and $\omega^2=\omega_0^2+2\alpha\theta$ need $\theta$ in radians and $\omega$ in rad/s. Convert rev/min with $\times\tfrac{2\pi}{60}$ and revolutions with $\times2\pi$ — and convert back if the question asks for revolutions.
3. Torque and moment of inertia about different axes. In $\tau=I\alpha$ both must be about the same (fixed) axis. For a hinged rod use $I=\tfrac13ML^2$ about the hinge, not $\tfrac{1}{12}ML^2$.
4. Constant-$\alpha$ equations for a varying torque. A swinging rod or door has a torque that changes with angle; use energy conservation, not $\omega^2=2\alpha\theta$ with the initial $\alpha$ (Example 5).
5. Assuming $a\le g$ or a zero hinge force. The free end of a released horizontal rod starts with $a=\tfrac32g$; the hinge still pushes up with $\tfrac14Mg$ at that instant.
Which of these pairs is not a correct linear–rotational analogue?
Exercises
Take $g=9.8\ \text{m/s}^2$ unless told otherwise. Strings are light and do not slip on pulleys; axles are frictionless unless a friction torque is given.
- 1 Express $600\ \text{rev/min}$ in rad/s.
- 2 A wheel starts from rest with $\alpha=2.5\ \text{rad/s}^2$. Find its angular velocity after $8.0\ \text{s}$ and the number of revolutions it has made.
- 3 A disc speeds up uniformly from $120\ \text{rev/min}$ to $360\ \text{rev/min}$ in $4.0\ \text{s}$. Find its angular acceleration and the number of revolutions in this time.
- 4 A grinding wheel turning at $50\ \text{rad/s}$ decelerates uniformly at $2.0\ \text{rad/s}^2$. Find the time to stop and the number of revolutions it makes.
- 5 The wheel of part 2 has radius $0.25\ \text{m}$. At $t=8.0\ \text{s}$ find, for a point on its rim, the speed, the tangential acceleration and the centripetal acceleration.
- 6 With constant angular acceleration, a wheel turns through $40\ \text{rad}$ in $4.0\ \text{s}$ and has angular velocity $15\ \text{rad/s}$ at the end. Find its initial angular velocity and its angular acceleration.
- 7 A fan starting from rest with constant angular acceleration makes $10$ revolutions in the first $5\ \text{s}$. How many does it make in the next $5\ \text{s}$?
- 8 Find the angular velocity of the minute hand of a clock, and the ratio of the angular velocities of the minute and hour hands.
- 1 A torque of $4.0\ \text{N m}$ acts on a wheel with $I=0.50\ \text{kg m}^2$. Find its angular acceleration.
- 2 A disc of mass $2.0\ \text{kg}$ and radius $0.30\ \text{m}$ turns on a fixed axle through its centre. A tangential force of $6.0\ \text{N}$ acts at its rim. Find the angular acceleration.
- 3 Repeat part 2 for a thin ring of the same mass and radius.
- 4 A wheel with $I=0.40\ \text{kg m}^2$ spinning at $30\ \text{rad/s}$ is stopped uniformly by a brake in $6.0\ \text{s}$. Find the braking torque.
- 5 A rope wound round a solid cylinder (mass $10\ \text{kg}$, radius $0.20\ \text{m}$) on a horizontal frictionless axle is pulled with a steady $25\ \text{N}$. Find the angular acceleration and the length of rope unwound in $2.0\ \text{s}$ from rest.
- 6 A $2.0\ \text{kg}$ block hangs from a string wound on a disc of mass $6.0\ \text{kg}$ and radius $0.25\ \text{m}$. Find the block's acceleration and the tension.
- 7 Blocks of $5.0\ \text{kg}$ and $3.0\ \text{kg}$ hang over a pulley that is a thin ring of mass $2.0\ \text{kg}$. Find the acceleration and both tensions.
- 8 A uniform rod of length $0.80\ \text{m}$, hinged at one end, is released from rest in the horizontal position. Find its initial angular acceleration and the initial acceleration of its free end.
- 9 A $4.0\ \text{kg}$ block on a rough table ($\mu_k=0.20$) is tied by a string over a pulley (a disc of mass $2.0\ \text{kg}$) at the table's edge to a hanging $2.0\ \text{kg}$ block. Find the acceleration and the tensions in the horizontal and vertical parts of the string.
- 1 Find the kinetic energy of a disc of mass $3.0\ \text{kg}$ and radius $0.40\ \text{m}$ spinning at $20\ \text{rad/s}$ about its axis.
- 2 A constant torque of $15\ \text{N m}$ turns a wheel through $10$ revolutions. Find the work done.
- 3 A motor delivers $2.0\ \text{kW}$ while turning at $1500\ \text{rev/min}$. Find the torque it exerts.
- 4 A flywheel with $I=5.0\ \text{kg m}^2$ is brought from rest to $100\ \text{rad/s}$. Find the work needed. How long does this take with a motor of constant power $500\ \text{W}$ (no losses)?
- 5 A uniform rod of length $1.0\ \text{m}$, hinged at one end, is released from rest in the horizontal position. Find its angular velocity and the speed of its free end as it passes the vertical.
- 6 A $1.0\ \text{kg}$ block hangs from a string wound on a disc of mass $2.0\ \text{kg}$ and radius $0.10\ \text{m}$. Use energy conservation to find the block's speed and the disc's angular velocity after the block has fallen $2.0\ \text{m}$ from rest.
- 7 A wheel with $I=0.20\ \text{kg m}^2$ spinning at $40\ \text{rad/s}$ is slowed by a constant friction torque of $0.050\ \text{N m}$. How many revolutions does it make before stopping?
- 8 Two flywheels have equal kinetic energies; $I_1=4I_2$. Find $\omega_1/\omega_2$ and $L_1/L_2$.
- 1 Write the rotational analogue of each of these, and the condition under which it holds: $v=u+at$; $F=ma$; $K=p^2/2m$; $P=Fv$; impulse $=\Delta p$.
- 2 A constant torque gives a wheel ($I=0.60\ \text{kg m}^2$) an angular momentum of $30\ \text{kg m}^2/\text{s}$ in $5.0\ \text{s}$, starting from rest. Find the torque and the final kinetic energy.
- 3 A $2.0\ \text{kg}$ block hangs from a string wound on a disc pulley (mass $4.0\ \text{kg}$, radius $0.20\ \text{m}$) whose axle has a friction torque of $0.40\ \text{N m}$. Find the block's acceleration.
- 4 A uniform rod ($2.0\ \text{kg}$, $1.5\ \text{m}$) lies on a smooth horizontal table, free to turn about a fixed vertical axis through its centre. A $3.0\ \text{N}$ force acts at one end, horizontal and perpendicular to the rod. Find $\alpha$, then $\omega$ and $K$ after $2.0\ \text{s}$ from rest; check $K$ against $W=\tau\theta$.
- 5 A uniform rod of length $1.0\ \text{m}$ hinged at one end is released from the horizontal. When it has turned through $60^\circ$, find its angular acceleration and its angular velocity.
- 6 A motor's armature ($I=0.020\ \text{kg m}^2$) reaches $3000\ \text{rev/min}$ from rest in $2.0\ \text{s}$ under a constant torque. Find the torque, the average power and the power at the end of the $2.0\ \text{s}$.
- 7 (Modelling) A flywheel-powered city bus stores energy in a solid steel disc of mass $500\ \text{kg}$ and radius $0.50\ \text{m}$ turning at $3000\ \text{rev/min}$. Find the stored energy in MJ, and for how long it could supply an average $20\ \text{kW}$ if all of it could be used.
E1. JEE Main · MCQ A wheel rotating at $1200\ \text{rev/min}$ is brought to rest with uniform angular retardation after making $50$ revolutions. The time it takes to stop is (A) $2.5\ \text{s}$ (B) $10\ \text{s}$ (C) $5\ \text{s}$ (D) $7.5\ \text{s}$
E2. JEE Main · Numerical A block of mass $1\ \text{kg}$ hangs from a light string wound round a uniform disc of mass $8\ \text{kg}$ that can turn freely about its horizontal axis. Taking $g=10\ \text{m/s}^2$, find the tension in the string (in N) while the block falls. Give the answer to the nearest integer.
E3. JEE Main · MCQ A uniform rod of length $L$, hinged at one end, is held horizontal and released. Immediately after release, the linear acceleration of its free end is (A) $g$ (B) $\tfrac32g$ (C) $\tfrac34g$ (D) $2g$
E4. JEE Main · Numerical A constant torque of $20\ \text{N m}$ acts on a wheel of moment of inertia $4\ \text{kg m}^2$, initially at rest, on a frictionless axle. Find the number of revolutions it makes in the first $10\ \text{s}$. Give the answer to the nearest integer.
E5. JEE Main · MCQ A thin ring and a uniform disc of the same mass and radius, each free to turn about its central axis, start from rest. The same constant torque acts on each for the same time. The ratio of the kinetic energy of the ring to that of the disc is then (A) $2$ (B) $1$ (C) $4$ (D) $\tfrac12$
E6. JEE Main · Numerical A uniform rod of length $1.2\ \text{m}$, hinged at one end, is released from rest in the horizontal position and swings down in a vertical plane. Taking $g=10\ \text{m/s}^2$, find the speed (in m/s) of its free end as it passes through the vertical. Give the answer to the nearest integer.
Research question. Can you measure the moment of inertia of a spinning wheel and the friction torque in its bearings using nothing more than a falling mass, a string and a phone video?
Why it matters. Flywheel energy stores in power grids and metro trains, regenerative brakes in electric cars and the spin-down tests that engineers run on turbines and hard-disc motors all depend on knowing $I$ and the losses in the bearings. The same two equations of this section — $\tau=I\alpha$ and the work–energy theorem for rotation — turn simple timing measurements into those numbers, and a spin-down curve tells a maintenance engineer when a bearing is starting to fail.
What to do.
- Mount a bicycle wheel (or a turntable or a spinning stool) so that it turns freely about a horizontal axle. Wind a string round the axle or hub, of measured radius $r$, and hang a known mass $m$ (about $100$–$500\ \text{g}$).
- Release the mass from rest and time its fall through a measured height $h$ (repeat five times). Find $a=2h/t^2$.
- Spin-down: spin the wheel with the string removed and film it, or count revolutions per $5\ \text{s}$ interval, until it stops. Plot $\omega$ against $t$; the slope gives the friction deceleration $\alpha_f$.
- With friction: $mg-T=ma$ and $Tr-\tau_f=I\dfrac ar$, where $\tau_f=I\alpha_f$. Solve for $I$, then $\tau_f$.
- Repeat with two other masses $m$. Does $I$ come out the same? Compare with your model of the wheel from Section 5.3.
Tools: Bicycle wheel or turntable, string, slotted masses, metre scale, vernier callipers for $r$, phone stopwatch or slow-motion video, a spreadsheet.
Hand in: Your timing table, the spin-down graph with its slope, the values of $I$ and $\tau_f$ with an uncertainty estimate, and one paragraph on which measurement limits the accuracy most.
Going further. Is the friction torque really constant? Check whether the spin-down graph is a straight line or curves at high speed (a sign of air drag, which grows with $\omega$). How would that change your value of $I$?
🧪 Self-check quiz
Q1. The rotational analogue of Newton's second law $F=ma$, for a rigid body turning about a fixed axis, is
Q2. A turntable rotates at $45\ \text{rev/min}$. Its angular velocity is
Q3. A spinning body with no external torque changes its shape so that its moment of inertia is halved. Its rotational kinetic energy
Q4. A motor exerts a torque of $10\ \text{N m}$ on a shaft turning at $100\ \text{rad/s}$. The power it delivers is
Q5. In an Atwood machine whose pulley has mass, the tensions $T_1$ on the heavier side and $T_2$ on the lighter side satisfy