Chapter 7 · Properties of Solids and Liquids

7.4 Surface Tension

A liquid surface behaves like a stretched skin: it pulls along every line drawn on it with a force $S$ per unit length and stores energy $S$ per unit area. From that one idea come round drops, the extra pressure $2S/R$ inside them, the contact angle and the rise of water up a thin tube, $h=2S\cos\theta/\rho gr$.

A steel needle laid gently on water floats, although steel is nearly eight times denser than water. Pond skaters run across the surface of a pond without getting their feet wet. Rain falls as round drops, and a soap film stretched on a wire loop snaps into the smallest area it can. Water creeps up a thin glass tube, into the fibres of a towel and up through the soil to a plant's roots — while mercury in a glass tube sits lower than the mercury around it. All of these come from one property of a liquid's surface: surface tension.

A liquid surface is not just the place where the liquid stops. The molecules there are in a different situation from those inside, and as a result the surface behaves like a stretched elastic membrane, always trying to shrink. In this section we explain where surface tension comes from and link it to surface energy, see how the angle of contact decides whether a liquid wets a solid, find the excess pressure inside drops and bubbles, and put it all together to explain capillary rise — the basis of the JEE Main experiment on the surface tension of water.

Surface tension and surface energy

Molecules of a liquid attract each other with short-range forces (they act only over a few molecular diameters). A molecule deep inside the liquid is pulled equally in all directions by its neighbours, so the net force on it is zero. A molecule at the surface has liquid neighbours only below and beside it; the pull of the few vapour molecules above is negligible. So it has a net inward pull, and — more importantly — it has fewer neighbours to bond with. Bringing a molecule from the interior to the surface means breaking some of its bonds: it costs energy. A liquid therefore has extra energy in proportion to its surface area, and, left to itself, it takes the shape of least surface area — a sphere, for a small drop where gravity hardly matters.

📘 Definition 7.14 — Surface tension

The surface tension $S$ of a liquid is the force per unit length acting in the surface, perpendicular to any line drawn in the surface, on each side of it, tending to pull the surface together:

$$S=\frac{F}{L}.$$

Its SI unit is $\text{N/m}$ and its dimensions are $[\text{MT}^{-2}]$. It depends on the liquid, on what lies on the other side of the surface (air, another liquid, a solid) and on the temperature: for most liquids $S$ decreases as the temperature rises, and dissolved detergents and soaps lower it strongly.

Typical values against air near $20^\circ\text{C}$: water $0.073\ \text{N/m}$, soap solution about $0.025$–$0.030\ \text{N/m}$, ethanol $0.022\ \text{N/m}$, mercury $0.465\ \text{N/m}$. A neat way to see the force is a soap film on a U-shaped wire frame with a light sliding wire of length $L$ across it. The film pulls the slider inwards; to hold it still you must pull outward with a force $F$. A film has two surfaces (front and back), each pulling with $SL$, so $F=2SL$.

Now pull the slider out slowly through a distance $x$. You do work $W=Fx=2SLx$, and the film's area grows by $Lx$ on each face, a total new surface of $\Delta A=2Lx$. So the work done per unit area of new surface is $W/\Delta A=S$. This work is stored as surface energy (at constant temperature).

📘 Definition 7.15 — Surface energy

The surface energy of a liquid is the extra potential energy its surface molecules have compared with molecules in the interior. The work needed to increase the area of a liquid surface by $\Delta A$ at constant temperature is

$$W=S\,\Delta A .$$
📐 Result 7.18 — Surface tension equals surface energy per unit area

At constant temperature, the surface tension of a liquid is numerically equal to its surface energy per unit area: $S$ in $\text{N/m}$ is the same number as $S$ in $\text{J/m}^2$. When counting area, count every surface that is created: a soap film or a soap bubble has two surfaces (inside and outside), a liquid drop has one.

Because surface energy is $S\times$area, splitting a drop into many small droplets creates surface and needs work, while droplets that merge into one drop lose surface and release energy (as heat). For a drop of radius $R$ split into $n$ equal droplets, volume conservation gives droplet radius $r=R/n^{1/3}$, and the total area grows from $4\pi R^2$ to $n\cdot4\pi r^2=n^{1/3}\cdot4\pi R^2$, so $W=4\pi R^2S\,(n^{1/3}-1)$.

✏️ Example 1 — A soap film on a wire frame
A soap film (surface tension $0.030\ \text{N/m}$) is formed on a U-shaped wire frame closed by a light sliding wire of length $6.0\ \text{cm}$. (a) Find the force needed to hold the slider in place. (b) Find the work done in pulling the slider out slowly by $2.0\ \text{cm}$, and check it against the increase in surface energy. (c) The frame is held vertical with the slider at the bottom. What mass hung from the slider keeps it in equilibrium?
(a) Two surfaces: $F=2SL=2\times0.030\times0.060=3.6\times10^{-3}\ \text{N}$.
(b) $W=Fx=3.6\times10^{-3}\times0.020=7.2\times10^{-5}\ \text{J}$. New area $2\times(0.060\times0.020)=2.4\times10^{-3}\ \text{m}^2$, and $S\Delta A=0.030\times2.4\times10^{-3}=7.2\times10^{-5}\ \text{J}$ ✓.
(c) $mg=2SL$: $m=\dfrac{3.6\times10^{-3}}{9.8}=3.7\times10^{-4}\ \text{kg}=0.37\ \text{g}$.
Note The force does not depend on how far the slider is pulled out — unlike a stretched spring. A liquid surface is not elastic: pulling it out simply brings more molecules up from the interior.
✏️ Example 2 — Spraying a drop, and the heat of merging
A water drop of radius $2.0\ \text{mm}$ is broken up into $1000$ identical droplets ($S=0.073\ \text{N/m}$). (a) Find the radius of each droplet. (b) Find the work needed. (c) If instead $1000$ such droplets merge into one drop of radius $2.0\ \text{mm}$ and all the energy released heats the drop, find the rise in its temperature (specific heat capacity of water $4200\ \text{J kg}^{-1}\text{K}^{-1}$, density $1.0\times10^3\ \text{kg/m}^3$).
Find the work in (b) before you open the solution:
(a) Volume conserved: $r=R/1000^{1/3}=2.0/10=0.20\ \text{mm}$.
(b) Area before $4\pi R^2=5.03\times10^{-5}\ \text{m}^2$; after $1000\times4\pi r^2=5.03\times10^{-4}\ \text{m}^2$. $W=S\Delta A=0.073\times4.52\times10^{-4}=3.30\times10^{-5}\ \text{J}$.
(c) Mass $m=\tfrac43\pi R^3\rho=3.35\times10^{-5}\ \text{kg}$. $\Delta T=\dfrac{W}{mc}=\dfrac{3.30\times10^{-5}}{3.35\times10^{-5}\times4200}=2.3\times10^{-4}\ \text{K}$.
⏱ Shortcut Per unit volume, the surface energy of drops of radius $r$ is $3S/r$, so for merging $\Delta T=\dfrac{3S}{\rho c}\left(\dfrac1r-\dfrac1R\right)=\dfrac{3\times0.073}{4.2\times10^6}(5000-500)=2.3\times10^{-4}\ \text{K}$ — tiny, but larger the smaller the droplets.

A soap film is formed on a wire frame with a sliding wire of length $L$. The surface tension of the solution is $S$. The force the film exerts on the slider is

Angle of contact

Where a liquid surface meets a solid, two kinds of attraction compete: cohesion (the attraction between molecules of the liquid) and adhesion (the attraction between molecules of the liquid and of the solid). If adhesion wins, the liquid spreads over the solid and climbs a little up its wall: water in a clean glass tumbler curves up at the edge. If cohesion wins, the liquid pulls back into itself and curves down at the wall: mercury in a glass tube, or water drops on a waxed car or a lotus leaf, which stand up as beads.

📘 Definition 7.16 — Angle of contact

The angle of contact $\theta$ between a liquid and a solid is the angle between the solid surface and the tangent to the liquid surface at the point of contact, measured inside the liquid.

  • $\theta\lt90^\circ$: the liquid wets the solid (adhesion dominates); the meniscus in a tube is concave (curving up at the wall). Water on clean glass: $\theta\approx0^\circ$.
  • $\theta\gt90^\circ$: the liquid does not wet the solid (cohesion dominates); the meniscus is convex. Mercury on glass: $\theta\approx140^\circ$; water on wax or a water-repellent fabric: $\theta\gt90^\circ$.

The angle of contact depends on the pair of substances, on the cleanliness of the surface and on impurities in the liquid.

Why the contact angle has the value it has. A drop on a flat solid has a line of contact where three surfaces meet: solid–air, solid–liquid and liquid–air, each with its own surface tension $S_\text{sa}$, $S_\text{sl}$, $S_\text{la}$. Each pulls the contact line along its own surface. In equilibrium the components along the solid surface balance.

📐 Result 7.19 — Equilibrium at the line of contact

For a liquid resting on a solid in air, the balance of surface-tension forces along the solid surface at the line of contact gives

$$S_\text{sa}=S_\text{sl}+S_\text{la}\cos\theta,\qquad\text{so}\qquad\cos\theta=\frac{S_\text{sa}-S_\text{sl}}{S_\text{la}}.$$

If $S_\text{sl}\lt S_\text{sa}$, then $\cos\theta\gt0$ and $\theta$ is acute (the liquid wets the solid); if $S_\text{sl}\gt S_\text{sa}$, $\theta$ is obtuse.

Detergents and waterproofing. Water alone has a fairly large $S_\text{la}$ and does not easily soak into greasy fibres. Detergent molecules gather at the surfaces; they lower the surface tension of water against air and against grease, which reduces the angle of contact. The water then wets the cloth and gets between the fibres and the dirt, and the grease is lifted off in tiny droplets surrounded by detergent. Waterproofing agents do the opposite: they coat fibres with a substance that water does not wet, raising the angle of contact above $90^\circ$, so water stands as beads and runs off. Soldering fluxes and the "wetting agents" sprayed with pesticides are other applications.

Water stands in round beads on a freshly waxed car bonnet, but spreads into a thin film on clean glass. This shows that

Excess pressure across a curved surface

Blow up a balloon and the stretched rubber squeezes the air inside, so the air inside is at a higher pressure than outside. A liquid surface does the same: wherever it is curved, its tension pulls it towards the centre of curvature, and the pressure on the concave side must be larger than on the convex side to hold it in place. The flatter the surface, the smaller this excess pressure; a plane surface has none.

📐 Law 7.20 — Excess pressure inside drops and bubbles

For a spherical surface of radius $R$ of a liquid with surface tension $S$, the pressure on the concave (inner) side exceeds that on the convex side by

  • a liquid drop in air, or an air bubble inside a liquid (one surface): $\ \Delta p=p_\text{in}-p_\text{out}=\dfrac{2S}{R}$;
  • a soap bubble in air (a thin film with two surfaces, inner and outer, of almost the same radius): $\ \Delta p=\dfrac{4S}{R}$.

For a surface curved in one direction only (a cylinder of radius $R$, such as a liquid film between two close parallel plates), $\Delta p=S/R$.

Derivation (by energy). Imagine the radius of a drop increasing slowly from $R$ to $R+dR$. The excess pressure pushes the surface out through $dR$ over an area $4\pi R^2$, doing work $\Delta p\cdot4\pi R^2\,dR$. The surface area grows by $d(4\pi R^2)=8\pi R\,dR$, which needs energy $S\cdot8\pi R\,dR$. Equating, $\Delta p=\dfrac{2S}{R}$. For a soap bubble two surfaces grow, the energy needed doubles, and $\Delta p=\dfrac{4S}{R}$.

The striking consequence is that the smaller the bubble, the larger the pressure inside it. Connect a small soap bubble to a large one through a tube and open the tap: air flows from the small bubble into the large one, so the small one shrinks and the large one grows (Interactive 1). The same effect makes it hard to start blowing up a balloon — and makes the tiny air sacs (alveoli) of the lungs prone to collapse, which is why the lungs produce a natural "surfactant" that lowers the surface tension of the fluid lining them.

🧭 Problem-solving strategy — Pressure inside drops and bubbles
  1. Count the surfaces: drop or bubble in a liquid — one ($2S/R$); soap bubble in air — two ($4S/R$).
  2. Find the pressure just outside the surface: $p_0$ in air; $p_0+\rho gh$ for a bubble at depth $h$ in a liquid.
  3. Add the excess pressure: $p_\text{in}=p_\text{out}+\Delta p$.
  4. For two bubbles stuck together, the common film separates two gases whose pressure difference is $4S/r_1-4S/r_2$; it bulges into the larger bubble with radius $r=\dfrac{r_1r_2}{r_2-r_1}$.
✏️ Example 3 — Three curved surfaces
Find (a) the excess pressure inside a water drop of radius $0.50\ \text{mm}$ ($S=0.073\ \text{N/m}$); (b) the excess pressure inside a soap bubble of radius $1.5\ \text{cm}$ ($S=0.025\ \text{N/m}$); (c) the total pressure inside an air bubble of radius $0.10\ \text{mm}$ at a depth of $20\ \text{cm}$ below the surface of water. Take atmospheric pressure as $1.013\times10^5\ \text{Pa}$.
(a) One surface: $\Delta p=\dfrac{2S}{R}=\dfrac{2\times0.073}{5.0\times10^{-4}}=292\ \text{Pa}$.
(b) Two surfaces: $\Delta p=\dfrac{4S}{R}=\dfrac{4\times0.025}{0.015}=6.7\ \text{Pa}$ — tiny, because the bubble is large.
(c) Outside the bubble: $p_0+\rho gh=1.013\times10^5+1000\times9.8\times0.20=1.013\times10^5+1960\ \text{Pa}$. One surface: $\Delta p=\dfrac{2\times0.073}{1.0\times10^{-4}}=1460\ \text{Pa}$. So $p_\text{in}=1.013\times10^5+1960+1460=1.047\times10^5\ \text{Pa}$.
Check In (c) the surface-tension term ($1460\ \text{Pa}$) is comparable with the depth term ($1960\ \text{Pa}$): for small bubbles neither may be dropped.
✏️ Example 4 — Two soap bubbles
Two soap bubbles of radii $2.0\ \text{cm}$ and $3.0\ \text{cm}$ are blown from a solution with $S=0.030\ \text{N/m}$. (a) Find the excess pressure inside each. (b) The bubbles come into contact and stick together, with a common film between them. Find the radius of curvature of the common film and say which way it bulges. (c) If instead the two bubbles were connected by a tube with a tap, what would happen when the tap is opened?
Find the radius of the common film in (b) first:
(a) $\Delta p_1=\dfrac{4\times0.030}{0.020}=6.0\ \text{Pa}$; $\ \Delta p_2=\dfrac{4\times0.030}{0.030}=4.0\ \text{Pa}$.
(b) The common film has the small bubble's gas ($p_0+6.0$) on one side and the large bubble's ($p_0+4.0$) on the other, so it carries a pressure difference $2.0\ \text{Pa}=\dfrac{4S}{r}$: $r=\dfrac{4\times0.030}{2.0}=0.060\ \text{m}=6.0\ \text{cm}$. Its concave side faces the higher pressure, so it bulges into the larger bubble.
(c) Air flows from the smaller bubble (higher pressure) to the larger. The small one shrinks — its pressure rises further as it does — and the large one grows until the small one has collapsed into a cap over the tube mouth.
⏱ Shortcut $\dfrac1r=\dfrac1{r_1}-\dfrac1{r_2}$, i.e. $r=\dfrac{r_1r_2}{r_2-r_1}=\dfrac{2\times3}{1}=6\ \text{cm}$. Note that $S$ cancels.

In Interactive 1 set $r_1=2.0\ \text{cm}$, $r_2=4.0\ \text{cm}$ and $S=0.030\ \text{N/m}$. When the tap is opened (press Play), which way does the air flow, and what are the two excess pressures?

With $r_1=2.0\ \text{cm}$, $r_2=4.0\ \text{cm}$, $S=0.030\ \text{N/m}$ the readouts show $\Delta p_1=4S/r_1=6.0\ \text{Pa}$ and $\Delta p_2=3.0\ \text{Pa}$, flow "from bubble 1 into bubble 2" and a final radius of $4.16\ \text{cm}$ $\left(=(2^3+4^3)^{1/3}\right)$. The smaller bubble has the higher pressure, so it empties into the larger one, and the gap gets worse as it shrinks — the two dots on the $\Delta p$–$r$ graph move apart. ($1.5\ \text{Pa}$ and $3.0\ \text{Pa}$ would come from $2S/R$, forgetting the second surface of the film.)
Interactive 1 — Two Soap Bubbles: Which One Wins?

Two soap bubbles sit on the ends of a tube with a closed tap. Set their radii and the surface tension, compare the excess pressures $4S/r$ on the graph, then press Play to open the tap. Air flows from high pressure to low — watch which bubble grows. (The volume of air is treated as constant; the excess pressures are only a few pascals.)

2.0 cm4.0 cm0.030 N/m
bubble 1: $4S/r_1$—
bubble 2: $4S/r_2$—
air flows—
final radius—

The excess pressure inside a soap bubble of radius $R$ is $\Delta p$. The excess pressure inside a soap bubble of radius $2R$ blown from the same solution is

Capillary rise

Dip a clean glass tube with a fine bore — a capillary tube (Latin capillus, a hair) — into water. The water rises inside it well above the outside level, and the finer the tube, the higher it goes. Dip it into mercury and the mercury inside stands below the outside level. This is capillarity, and it follows from the two ideas above: the angle of contact and the excess pressure across a curved surface.

The pressure argument. Water wets glass ($\theta\approx0$), so the meniscus in the tube is concave, part of a sphere of radius $R=r/\cos\theta$, where $r$ is the radius of the tube (for $\theta=0$ it is a hemisphere, $R=r$). Just below a concave surface the pressure is lower than above it by $2S/R$. At first the water inside is level with the outside, so the pressure just under the meniscus is $p_0-2S/R$, less than the pressure $p_0$ at the same level outside. Water is pushed up the tube until the column of height $h$ makes up the difference: $\rho gh=\dfrac{2S}{R}=\dfrac{2S\cos\theta}{r}$.

The force argument. Around the circle of contact, of length $2\pi r$, the liquid surface pulls with $S$ per unit length along the tangent to the meniscus, which makes angle $\theta$ with the wall. By Newton's third law the wall pulls the liquid up with vertical component $2\pi rS\cos\theta$. This supports the weight of the raised column, $\pi r^2h\rho g$ (neglecting the small volume in the meniscus). Setting them equal gives the same answer.

📐 Law 7.21 — Capillary rise (Jurin's law)

A liquid of surface tension $S$, density $\rho$ and angle of contact $\theta$ rises in a vertical capillary tube of radius $r$ to a height

$$h=\frac{2S\cos\theta}{\rho gr}$$

above the outside level (neglecting the liquid in the meniscus). For $\theta\lt90^\circ$, $h\gt0$ (capillary rise: water in glass); for $\theta\gt90^\circ$, $h\lt0$ (capillary depression: mercury in glass). For a given liquid and tube material, $hr$ is constant: $h\propto1/r$.

Three consequences are favourites in JEE Main:

Capillarity carries water up through the fine gaps in soil and the fibres of a towel, draws ink into the nib of a fountain pen and oil up a lamp wick, and is used in the JEE Main experiment: measure $h$ and $r$ with a travelling microscope and compute $S=\dfrac{\rho grh}{2\cos\theta}$. Add a little detergent and the rise drops sharply, showing that the surface tension has fallen.

✏️ Example 5 — Water rises, mercury falls
A clean glass capillary tube of internal radius $0.25\ \text{mm}$ is dipped vertically into (a) water ($S=0.073\ \text{N/m}$, $\theta=0^\circ$) and (b) mercury ($S=0.465\ \text{N/m}$, $\theta=140^\circ$, density $13.6\times10^3\ \text{kg/m}^3$). Find the capillary rise or depression in each case.
(a) $h=\dfrac{2\times0.073\times1}{1000\times9.8\times2.5\times10^{-4}}=\dfrac{0.146}{2.45}=0.0596\ \text{m}=5.96\ \text{cm}$ (rise).
(b) $h=\dfrac{2\times0.465\times\cos140^\circ}{13\,600\times9.8\times2.5\times10^{-4}}=\dfrac{0.930\times(-0.766)}{33.32}=-0.0214\ \text{m}$: a depression of $2.14\ \text{cm}$.
Compare Mercury has more than six times the surface tension of water but is $13.6$ times denser and does not wet glass — so it is pushed down, and by less.
Check Units: $\dfrac{\text{N/m}}{(\text{kg/m}^3)(\text{m/s}^2)(\text{m})}=\dfrac{\text{N/m}}{\text{N/m}^2}=\text{m}$ ✓.
✏️ Example 6 — A short tube and a tilted tube
The tube of Example 5 (radius $0.25\ \text{mm}$, in which water rises $5.96\ \text{cm}$) is used again with water. (a) Only $4.0\ \text{cm}$ of the tube now sticks out above the water surface. Does the water overflow? Find the radius of the meniscus and the angle the water surface makes with the glass at the top. (b) The full-length tube is tilted to $60^\circ$ from the vertical. Find the length of the water column in the tube. (c) Find the weight of water held up in the vertical tube of Example 5.
Find the radius of the meniscus in (a) before you open the solution:
(a) No overflow: the water rises to the rim and stops, with a flatter meniscus. $R'=\dfrac{2S}{\rho g\ell}=\dfrac{0.146}{1000\times9.8\times0.040}=3.72\times10^{-4}\ \text{m}=0.372\ \text{mm}$ (check: $R'=r\,h/\ell=0.25\times5.96/4.0$ ✓).
Angle $\cos\theta'=\dfrac{r}{R'}=\dfrac{0.25}{0.372}=0.671$, so $\theta'=47.8^\circ$ — the surface meets the rim at a steeper angle than the true contact angle $0^\circ$, which the rim's edge allows.
(b) The vertical height stays $5.96\ \text{cm}$: $\ell=\dfrac{5.96}{\cos60^\circ}=11.9\ \text{cm}$ along the tube.
(c) $W=2\pi rS\cos\theta=2\pi\times2.5\times10^{-4}\times0.073=1.15\times10^{-4}\ \text{N}$ (check: $\pi r^2h\rho g=1.15\times10^{-4}\ \text{N}$ ✓) — about $12\ \text{mg}$ of water.
⏱ Shortcut $hr=\text{constant}$ and $hR=\text{constant}$ answer most capillary questions without any numbers for $S$ or $\rho$.

In Interactive 2 choose water and a tube of radius $0.50\ \text{mm}$ sticking out $12\ \text{cm}$: the water rises about $3.0\ \text{cm}$. Predict the rise when you reduce the radius to $0.25\ \text{mm}$.

Water with $r=0.50\ \text{mm}$ gives $h=2.98\ \text{cm}$; with $r=0.25\ \text{mm}$ the readout shows $h=5.96\ \text{cm}$, meniscus radius $0.25\ \text{mm}$: halving $r$ doubles $h$, because $h=2S\cos\theta/\rho gr\propto1/r$ ($12\ \text{cm}$ would need $h\propto1/r^2$). Now lower the tube to $4.0\ \text{cm}$: the water stops at the rim, the meniscus radius grows to $0.372\ \text{mm}$ and the angle at the rim reads $47.8^\circ$ — no overflow. Switch to mercury to see a convex meniscus pushed below the outside level.
Interactive 2 — Capillary Tube: Rise, Depression and a Short Tube

A vertical glass capillary (bore drawn much wider than life) dips into a liquid. Choose the liquid, the bore radius and how far the tube sticks out of the surface, then press Play to watch the liquid climb (or sink) to its final level. The graph shows $h$ against $r$ for this liquid — Jurin's law $h\propto1/r$. Make the tube shorter than $h$ and see what happens at the rim.

0.50 mm12 cm
height $h$—
meniscus radius—
angle at the surface—
weight held up—
⚠️ JEE Main traps

1. Counting surfaces. A soap bubble or a soap film has two surfaces: excess pressure $4S/R$, work to blow a bubble of radius $R$ is $S\times2\times4\pi R^2=8\pi R^2S$, force on a slider $2SL$. A drop, or an air bubble inside a liquid, has one: $2S/R$ and $4\pi R^2S$.

2. Smaller bubble, larger pressure. $\Delta p\propto1/R$. When two bubbles are connected the small one empties into the large one; the common film of two stuck bubbles bulges into the larger one, with radius $r_1r_2/(r_2-r_1)$.

3. Forgetting the outside pressure. The pressure inside an air bubble at depth $h$ is $p_0+\rho gh+2S/R$; "excess pressure" alone is only the last term.

4. Capillary tube of insufficient length. The liquid never overflows; the meniscus radius increases so that $R'\ell=Rh$. And in a tilted tube the vertical height is unchanged — the length along the tube is $h/\cos\alpha$.

5. Radius versus diameter, and units. Jurin's law uses the tube's radius in metres; $S$ in N/m. A rise of a few centimetres needs $r$ of a fraction of a millimetre — if you get kilometres or micrometres, check the powers of ten.

Water rises $4.0\ \text{cm}$ in a capillary tube. In a tube of the same glass with half the radius, tilted so that it makes $60^\circ$ with the vertical, the length of the water column inside the tube is

Exercises

Take $g=9.8\ \text{m/s}^2$, the surface tension of water $0.073\ \text{N/m}$ with angle of contact $0^\circ$ on clean glass, the density of water $1.0\times10^3\ \text{kg/m}^3$ and atmospheric pressure $1.013\times10^5\ \text{Pa}$ unless told otherwise.

I
Surface tension and surface energy.
  • 1 A soap film ($S=0.040\ \text{N/m}$) is held on a frame by a slider $5.0\ \text{cm}$ long. Find the force on the slider.
  • 2 Find the work needed to increase the area of a soap film on a frame from $10\ \text{cm}^2$ to $40\ \text{cm}^2$ ($S=0.030\ \text{N/m}$).
  • 3 Find the work done in blowing a soap bubble of radius $3.0\ \text{cm}$ ($S=0.030\ \text{N/m}$).
  • 4 A thin wire ring of radius $2.5\ \text{cm}$ lies flat on a water surface. Find the extra force, beyond its weight, needed to lift it clear of the surface.
  • 5 A greased needle $3.0\ \text{cm}$ long floats on water. Assuming the surface pulls vertically upward along both sides of the needle, estimate the largest mass it can have.
  • 6 Find the work needed to spray a water drop of radius $1.0\ \text{mm}$ into droplets of radius $0.10\ \text{mm}$.
  • 7 Sixty-four mercury drops, each of radius $1.0\ \text{mm}$, merge into one drop ($S=0.465\ \text{N/m}$). Find the energy released.
  • 8 Explain, in terms of molecules, why a small drop is spherical and why surface tension falls as the temperature rises.
1 $F=2SL=2\times0.040\times0.050=4.0\times10^{-3}\ \text{N}$.
2 Two surfaces: $W=S\times2\Delta A=0.030\times2\times30\times10^{-4}=1.8\times10^{-4}\ \text{J}$.
3 $W=8\pi r^2S=8\pi(0.030)^2(0.030)=6.79\times10^{-4}\ \text{J}$.
4 The surface pulls down along the inner and the outer edge, each of length $\approx2\pi r$: $F=2\times2\pi rS=4\pi(0.025)(0.073)=2.29\times10^{-2}\ \text{N}$.
5 $mg=2LS=2\times0.030\times0.073=4.38\times10^{-3}\ \text{N}$, so $m=4.5\times10^{-4}\ \text{kg}=0.45\ \text{g}$.
6 $n=(1.0/0.10)^3=1000$; $\Delta A=4\pi(1000r^2-R^2)=4\pi(10^{-5}-10^{-6})=1.13\times10^{-4}\ \text{m}^2$; $W=0.073\times1.13\times10^{-4}=8.26\times10^{-6}\ \text{J}$.
7 $R=64^{1/3}r=4.0\ \text{mm}$. $\Delta A=4\pi(64r^2-R^2)=4\pi(64-16)\times10^{-6}=6.03\times10^{-4}\ \text{m}^2$; $E=0.465\times6.03\times10^{-4}=2.81\times10^{-4}\ \text{J}$.
8 Surface molecules have fewer neighbours, so the surface carries extra energy; a drop minimises its energy by minimising its area, and for a given volume a sphere has the least area. Heating makes the molecules move more vigorously and weakens the effective attraction (the liquid expands), so less energy is needed to bring molecules to the surface: $S$ falls.
II
Angle of contact and excess pressure.
  • 1 For a liquid on a solid, $S_\text{sa}-S_\text{sl}=0.050\ \text{N/m}$ and $S_\text{la}=0.073\ \text{N/m}$. Find the angle of contact.
  • 2 Say whether each liquid wets the solid, and the shape of its meniscus in a tube: water–clean glass, mercury–glass, water–paraffin wax, kerosene–glass.
  • 3 Find the excess pressure inside a mercury drop of radius $2.0\ \text{mm}$ ($S=0.465\ \text{N/m}$).
  • 4 Find the excess pressure inside a soap bubble of radius $2.5\ \text{cm}$ ($S=0.025\ \text{N/m}$).
  • 5 Find the excess pressure inside an air bubble of radius $0.20\ \text{mm}$ just below the surface of water.
  • 6 The bubble of part 5 is $1.5\ \text{m}$ below the surface. Find the total pressure inside it.
  • 7 Find the radius of a soap bubble ($S=0.030\ \text{N/m}$) whose excess pressure is $12\ \text{Pa}$.
  • 8 Explain why hot soapy water washes greasy clothes better than cold plain water.
  • 9 As a soap bubble is blown bigger, does the pressure inside it rise or fall? Why is the first breath into a new balloon the hardest?
1 $\cos\theta=\dfrac{0.050}{0.073}=0.685$, so $\theta=46.8^\circ$.
2 Water–clean glass: wets ($\theta\approx0^\circ$), concave. Mercury–glass: does not wet ($\theta\approx140^\circ$), convex. Water–wax: does not wet ($\theta\gt90^\circ$), convex. Kerosene–glass: wets ($\theta\approx0^\circ$), concave.
3 $\Delta p=\dfrac{2S}{R}=\dfrac{0.930}{2.0\times10^{-3}}=465\ \text{Pa}$.
4 $\Delta p=\dfrac{4S}{R}=\dfrac{0.100}{0.025}=4.0\ \text{Pa}$.
5 One surface: $\Delta p=\dfrac{2\times0.073}{2.0\times10^{-4}}=730\ \text{Pa}$.
6 $p=p_0+\rho gh+\dfrac{2S}{R}=1.013\times10^5+14\,700+730=1.167\times10^5\ \text{Pa}$.
7 $r=\dfrac{4S}{\Delta p}=\dfrac{0.120}{12}=0.010\ \text{m}=1.0\ \text{cm}$.
8 Soap and heat both lower the surface tension of water; soap also lowers the water–grease surface tension, so the angle of contact falls and the water wets the fibres, gets under the grease and carries it off in small droplets.
9 It falls: $\Delta p=4S/R$ decreases as $R$ grows. For a balloon the rubber's tension plays the part of $S$; when it is small and tightly curved, a large excess pressure is needed to expand it — after it has grown, less is needed.
III
Capillary rise.
  • 1 Find the height to which water rises in a clean glass capillary of radius $0.40\ \text{mm}$.
  • 2 What bore radius is needed for water to rise $10\ \text{cm}$?
  • 3 Find the depression of mercury ($S=0.465\ \text{N/m}$, $\theta=140^\circ$, density $13.6\times10^3\ \text{kg/m}^3$) in a glass tube of radius $1.0\ \text{mm}$, in mm.
  • 4 A liquid of density $800\ \text{kg/m}^3$ that wets glass ($\theta=0^\circ$) rises $2.5\ \text{cm}$ in a tube of radius $0.30\ \text{mm}$. Find its surface tension.
  • 5 Water would rise $8.0\ \text{cm}$ in a certain tube, but only $5.0\ \text{cm}$ of the tube is above the surface. Describe what happens and find the angle the water surface makes with the glass at the rim.
  • 6 The tube of part 1 is inclined at $45^\circ$ to the vertical. Find the length of the water column in it.
  • 7 How high would water rise in the tube of part 1 in a laboratory on the Moon ($g_\text{Moon}=g/6$)?
  • 8 (Experiment) In a tube of radius $0.30\ \text{mm}$ tap water rises $4.8\ \text{cm}$; after a few drops of detergent are added it rises only $2.1\ \text{cm}$. Find the surface tension in each case and comment.
1 $h=\dfrac{2\times0.073}{1000\times9.8\times4.0\times10^{-4}}=0.0372\ \text{m}=3.72\ \text{cm}$.
2 $r=\dfrac{2S}{\rho gh}=\dfrac{0.146}{1000\times9.8\times0.10}=1.49\times10^{-4}\ \text{m}=0.149\ \text{mm}$.
3 $h=\dfrac{2\times0.465\times\cos140^\circ}{13\,600\times9.8\times1.0\times10^{-3}}=-5.35\times10^{-3}\ \text{m}$: depressed by $5.35\ \text{mm}$.
4 $S=\dfrac{\rho grh}{2}=\dfrac{800\times9.8\times3.0\times10^{-4}\times0.025}{2}=0.0294\ \text{N/m}$.
5 The water rises to the rim and stops (no overflow); the meniscus flattens to $R'=R\times\dfrac{8.0}{5.0}=1.6r$. Then $\cos\theta'=\dfrac{r}{R'}=0.625$, $\theta'=51^\circ$.
6 $\ell=\dfrac{3.72}{\cos45^\circ}=5.27\ \text{cm}$.
7 $h\propto1/g$: $6\times3.72=22.3\ \text{cm}$.
8 $S=\dfrac{\rho grh}{2}$: $\dfrac{1000\times9.8\times3.0\times10^{-4}\times0.048}{2}=0.071\ \text{N/m}$ and, with detergent, $0.031\ \text{N/m}$. The detergent has more than halved the surface tension — the reason it helps water penetrate fabrics.
IV
Harder problems and applications.
  • 1 Two soap bubbles of radii $4.0\ \text{cm}$ and $6.0\ \text{cm}$ stick together. Find the radius of curvature of their common film.
  • 2 Find the work done in slowly enlarging a soap bubble from radius $1.0\ \text{cm}$ to $3.0\ \text{cm}$ ($S=0.030\ \text{N/m}$), ignoring the work done against the atmosphere.
  • 3 Two clean, parallel vertical glass plates $0.50\ \text{mm}$ apart dip into water. Using a force balance on the water between them, find how high it rises.
  • 4 Air is blown slowly through a fine tube whose open end, of radius $0.10\ \text{mm}$, is $5.0\ \text{cm}$ below the surface of water. Find the least gauge pressure in the tube that will form a bubble there.
  • 5 Water droplets of radius $0.010\ \text{mm}$ merge to form a drop of radius $1.0\ \text{mm}$. Find the rise in temperature if all the energy released heats the water ($c=4200\ \text{J kg}^{-1}\text{K}^{-1}$).
  • 6 A thin water film $0.050\ \text{mm}$ thick lies between two flat glass plates, each $10\ \text{cm}\times10\ \text{cm}$. The water wets the glass and its edges form semicircular (cylindrical) surfaces. Find the force needed to pull the plates straight apart.
  • 7 Find the mass of water held up in a clean glass capillary of radius $0.50\ \text{mm}$, in mg.
1 $r=\dfrac{r_1r_2}{r_2-r_1}=\dfrac{4.0\times6.0}{2.0}=12\ \text{cm}$, bulging into the larger bubble.
2 $W=S\times2\times4\pi(r_2^2-r_1^2)=0.030\times8\pi\times(9-1)\times10^{-4}=6.03\times10^{-4}\ \text{J}$.
3 For a length $L$ of plate: $2SL=\rho g(Ldh)$, so $h=\dfrac{2S}{\rho gd}=\dfrac{0.146}{1000\times9.8\times5.0\times10^{-4}}=0.0298\ \text{m}=2.98\ \text{cm}$ — the same as a tube of radius $d$.
4 The air must overcome the water's hydrostatic pressure and then the excess pressure of the bubble, which is greatest when the bubble is a hemisphere of radius $0.10\ \text{mm}$: $p_\text{g}=\rho gh+\dfrac{2S}{r}=490+1460=1950\ \text{Pa}$.
5 $\Delta T=\dfrac{3S}{\rho c}\left(\dfrac1r-\dfrac1R\right)=\dfrac{3\times0.073}{4.2\times10^6}\times(10^5-10^3)=5.2\times10^{-3}\ \text{K}$.
6 Inside the film the pressure is below atmospheric by $\dfrac{S}{d/2}=\dfrac{2\times0.073}{5.0\times10^{-5}}=2920\ \text{Pa}$; $F=2920\times0.010=29.2\ \text{N}$ — a thin wet film makes two plates surprisingly hard to separate.
7 $mg=2\pi rS$: $m=\dfrac{2\pi\times5.0\times10^{-4}\times0.073}{9.8}=2.34\times10^{-5}\ \text{kg}=23.4\ \text{mg}$.
🎯 Exam corner JEE Main · MCQJEE Main · Numerical

E1. JEE Main · MCQ A soap bubble is slowly blown up from radius $R$ to radius $2R$. If the surface tension of the solution is $S$, the work done against surface tension is (A) $12\pi R^2S$ (B) $24\pi R^2S$ (C) $8\pi R^2S$ (D) $6\pi R^2S$

Area Two surfaces: increase in area $2\times4\pi\left[(2R)^2-R^2\right]=24\pi R^2$.
Work $W=S\Delta A=24\pi R^2S$.
Answer (B).
⏱ Shortcut (A) counts only one surface. For a soap bubble always use $8\pi S(r_2^2-r_1^2)$.

E2. JEE Main · Numerical An air bubble of radius $0.10\ \text{mm}$ is formed $10\ \text{cm}$ below the surface of water ($S=0.070\ \text{N/m}$, density $1000\ \text{kg/m}^3$, $g=10\ \text{m/s}^2$). By how many pascals does the pressure inside the bubble exceed atmospheric pressure? Give the answer to the nearest integer.

Depth $\rho gh=1000\times10\times0.10=1000\ \text{Pa}$.
Surface One surface: $\dfrac{2S}{r}=\dfrac{0.14}{1.0\times10^{-4}}=1400\ \text{Pa}$.
Answer $p_\text{in}-p_0=1000+1400=2400$.
⏱ Shortcut Two separate terms, both needed: $1400$ alone (excess pressure only) and $3800$ (using $4S/r$) are the traps.

E3. JEE Main · MCQ In a capillary tube water would rise to $6.0\ \text{cm}$. The tube is pushed down until only $4.0\ \text{cm}$ of it is above the water surface. Then (A) water flows out of the top as a small fountain (B) water rises only $4.0\ \text{cm}$ but the meniscus becomes hemispherical with a smaller radius (C) the water level in the tube falls below the outside level (D) water reaches the top and stays there, with a meniscus of larger radius than before

Idea The pressure balance $2S/R=\rho g\ell$ can be met with the shorter column $\ell=4.0\ \text{cm}$ if the meniscus radius grows: $R'=R\times\dfrac{6.0}{4.0}=1.5R$.
Energy An overflowing fountain would be a perpetual-motion machine, so (A) is impossible.
Answer (D).
⏱ Shortcut $hR=\text{constant}$: shorter column $\Rightarrow$ flatter (larger-radius) meniscus.

E4. JEE Main · Numerical Water rises to a height of $6.0\ \text{cm}$ in a vertical capillary tube. In a second tube of the same glass but half the radius, held at $60^\circ$ to the vertical, what length (in cm) of the tube does the water occupy above the outside water level? Give the answer to the nearest integer.

Radius $h\propto1/r$: vertical height $12\ \text{cm}$.
Tilt Length along the tube $\ell=\dfrac{12}{\cos60^\circ}=24\ \text{cm}$.
Answer $24$.
⏱ Shortcut Two independent factors: $\times2$ for the radius, $\times\dfrac{1}{\cos\alpha}=2$ for the tilt.

E5. JEE Main · Numerical A liquid drop of radius $1.0\ \text{cm}$ is broken into $1000$ identical droplets. The surface tension of the liquid is $0.070\ \text{N/m}$. If the work done is $x\times10^{-5}\ \text{J}$, find $x$ to the nearest integer. (Take $\pi=3.14$.)

Radius $r=R/1000^{1/3}=R/10$; total new area $1000\times4\pi(R/10)^2=10\times4\pi R^2$.
Work $W=S\times4\pi R^2(10-1)=0.070\times4\times3.14\times10^{-4}\times9=7.91\times10^{-4}\ \text{J}=79.1\times10^{-5}\ \text{J}$.
Answer $79$.
⏱ Shortcut $W=4\pi R^2S\,(n^{1/3}-1)$ — here $n^{1/3}-1=9$, not $n-1=999$.

E6. JEE Main · MCQ Two soap bubbles of radii $3.0\ \text{cm}$ and $4.0\ \text{cm}$ come into contact and stick together. The radius of curvature of the film separating them is (A) $12\ \text{cm}$ (B) $1.7\ \text{cm}$ (C) $5.0\ \text{cm}$ (D) $7.0\ \text{cm}$

Pressures The film separates gases at $p_0+4S/r_1$ and $p_0+4S/r_2$, so $\dfrac{4S}{r}=\dfrac{4S}{r_1}-\dfrac{4S}{r_2}$.
Radius $r=\dfrac{r_1r_2}{r_2-r_1}=\dfrac{3.0\times4.0}{1.0}=12\ \text{cm}$.
Answer (A).
⏱ Shortcut (B) is $\dfrac{r_1r_2}{r_1+r_2}$ (wrong sign); (C) is $\sqrt{r_1^2+r_2^2}$, the radius when two bubbles merge into one in a vacuum — a different question.
🔬 Research–Teaching NexusResearch-tutored · optional, about 45 minutes

Research question. How much does a household detergent lower the surface tension of water, and is there a concentration beyond which adding more makes no difference?

Why it matters. Surfactants — the molecules in detergents, shampoos and the fluid lining our lungs — are among the most widely used chemicals in the world. Doctors give artificial lung surfactant to premature babies whose lungs cannot yet make their own, because without it the tiny air sacs collapse (Law 7.20: small bubbles have large excess pressures). Agricultural sprays, inkjet inks, firefighting foams and oil-spill clean-ups are all designed around how strongly a surfactant lowers $S$. Capillary rise gives you a simple, accurate way to measure it.

What to do.

  1. Clean a glass capillary tube (or a few) thoroughly and find its internal radius — with a travelling microscope if you have one, or by drawing a measured length of water into it and weighing it ($m=\rho\pi r^2\ell$).
  2. Clamp the tube vertically in a beaker of distilled water and measure the capillary rise $h$ from the outside surface to the bottom of the meniscus. Compute $S=\rho grh/2$.
  3. Make detergent solutions of increasing strength: 1 drop, 2, 4, 8, 16 drops per litre. For each, rinse the tube with the solution and measure $h$.
  4. Plot $S$ against the number of drops per litre (also try a logarithmic scale). Where does the curve level off?
  5. Repeat the distilled-water measurement with warm water to see the effect of temperature.

Tools: Capillary tubes, beaker, clamp stand, ruler with mm scale or travelling microscope, magnifying glass, dropper, liquid detergent, thermometer.

Hand in: A table of $h$ and $S$ for each concentration with uncertainties, the graph of $S$ against concentration, and a paragraph explaining the shape of the curve in terms of detergent molecules at the surface.

Going further. Measure the rise in tubes of three different radii in plain water and plot $h$ against $1/r$. Is it a straight line through the origin, as Jurin's law predicts? Use its slope for a more accurate value of $S$.

Instructor note: clean tubes give $S\approx0.070$–$0.073\ \text{N/m}$ for distilled water; dirty tubes give low, scattered values, so insist on careful cleaning. Detergent typically brings $S$ down to about $0.025$–$0.035\ \text{N/m}$, with most of the drop at low concentrations and a plateau once the surface is saturated (near the critical micelle concentration) — a good link to chemistry. Warm water gives a small but measurable fall in $S$.

🧪 Self-check quiz

0/5 correct

Q1. The dimensional formula of surface tension is

Q2. The excess pressure inside a soap bubble of radius $R$ blown from a solution of surface tension $S$ is

Q3. Adding a detergent to water

Q4. Water rises to a height $h$ in a capillary tube of radius $r$. In a tube of the same glass of radius $2r$ it rises to

Q5. Mercury in a glass capillary tube stands below the level outside because