1.3 Chemical Equations and Stoichiometry
A balanced equation is a recipe written in moles. Read its coefficients as mole ratios and every quantitative question — how much product, which reactant runs out first, what yield, how pure the sample, how much of a solution — becomes the same three-step calculation: given → moles → ratio → wanted.
A car's airbag must fill in about thirty milliseconds. Inside the steering wheel there is no gas cylinder — only a few tens of grams of a white solid, sodium azide, which an electric spark decomposes into sodium metal and nitrogen gas. Put in too little solid and the bag is soft when the driver's head reaches it; put in too much and it bursts. The designer needs one number — the mass of solid that gives exactly the right volume of gas — and that number comes from the balanced equation $\mathrm{2NaN_{3}(s) \rightarrow 2Na(s) + 3N_{2}(g)}$ and nothing else. The same kind of calculation decides how much ore a blast furnace needs, how much fertiliser a plant can make from a tanker of ammonia, and how many millilitres of acid neutralise a spill.
This quantitative side of chemistry is called stoichiometry (from the Greek stoicheion, element, and metron, measure). It rests on two ideas from earlier in this chapter: atoms are neither created nor destroyed in a chemical reaction (Section 1.1), and amounts of substance are counted in moles (Section 1.2). In this section we first learn to write and balance equations, then read them as mole ratios to link masses, gas volumes and amounts in solution; we then deal with the real-world complications that JEE Main loves — a reactant that runs out first, a yield below 100 %, an impure sample, and reactions that happen one after another or side by side.
Unless a problem says otherwise, this section uses the rounded molar masses ($\mathrm{g\,mol^{-1}}$) common in JEE Main: H 1, C 12, N 14, O 16, Na 23, Mg 24, Al 27, Si 28, P 31, S 32, Cl 35.5, K 39, Ca 40, Fe 56, Zn 65, Ag 108, Ba 137; the molar volume of an ideal gas at STP ($273.15\ \mathrm{K}$, $1\ \mathrm{atm}$) $V_{m}=22.4\ \mathrm{L\,mol^{-1}}$; and $R=0.0821\ \mathrm{L\,atm\,mol^{-1}\,K^{-1}}$.
Chemical equations and balancing by inspection
A chemical equation is a compact statement of what happens in a reaction: which substances react (the reactants, on the left), which are formed (the products, on the right), and in what proportions. The proportions are the numbers written in front of the formulas.
A chemical equation represents a reaction by the formulas of the reactants and products, joined by an arrow, with the physical state of each substance shown as $\mathrm{(s)}$, $\mathrm{(l)}$, $\mathrm{(g)}$ or $\mathrm{(aq)}$. In the general equation
$$a\,\mathrm{A} + b\,\mathrm{B} \rightarrow c\,\mathrm{C} + d\,\mathrm{D}$$the numbers $a,b,c,d$ are the stoichiometric coefficients (symbol $\nu$, "nu"). A coefficient multiplies the whole formula after it; a coefficient of 1 is not written. The equation is balanced when every element has the same number of atoms on both sides and, for ionic equations, the total charge is the same on both sides. Conditions such as heat ($\Delta$), a catalyst or a temperature are written above or below the arrow: $\mathrm{2KClO_{3}(s)}$ $\mathrm{\xrightarrow[\Delta]{MnO_{2} } 2KCl(s) + 3O_{2}(g)}$.
Why must an equation balance? Because a reaction only rearranges atoms: bonds break and new bonds form, but each atom keeps its identity (nuclear changes are a different subject). Electrons are not lost to the outside world either, so the total charge cannot change. Mass is conserved because the atoms are. These three facts fix what an equation can and cannot claim.
In a balanced chemical equation (an ordinary chemical reaction, no nuclear change):
- the number of atoms of each element is the same on both sides;
- the total charge is the same on both sides;
- hence the total mass of reactants that react equals the total mass of products formed (law of conservation of mass).
The total number of molecules (or moles) is not conserved in general: in $\mathrm{N_{2}(g) + 3H_{2}(g) \rightarrow 2NH_{3}(g)}$ four moles of gas become two. Gas volumes at the same temperature and pressure are proportional to moles, so they are not conserved either.
You may change coefficients while balancing, but never subscripts: writing $\mathrm{H_{2}O_{2}}$ in place of $\mathrm{H_{2}O}$ "balances" the oxygen but describes a different substance. For most equations met in this chapter, balancing by inspection — trial and adjustment guided by a few habits — is quick. Redox equations with many species are better balanced by the oxidation-number or ion–electron methods of Section 7.1.
- Write correct formulas for every reactant and product (charges of ions balanced inside each formula). Do not touch them again.
- Start with the most complicated formula, and balance an element that occurs in only one substance on each side. Leave elements that occur in several places (often O and H) and free elements (such as $\mathrm{O_{2}}$, $\mathrm{Fe}$) to the end.
- Treat a polyatomic ion that survives unchanged ($\mathrm{SO_{4}^{2-}}$, $\mathrm{PO_{4}^{3-}}$, $\mathrm{NO_{3}^{-}}$) as a single unit.
- If a free element needs a half-integer coefficient (e.g. $\tfrac{13}{2}\mathrm{O_{2}}$), use it, then multiply the whole equation by the denominator.
- Reduce to the smallest whole numbers, then check every element and, for ions, the charge.
$\mathrm{2Ca_{3}(PO_{4})_{2}(s) + 6SiO_{2}(s) + 10C(s)}$ $\mathrm{\rightarrow 6CaSiO_{3}(l) + P_{4}(g) + 10CO(g)}$.
A balanced equation can be read at three levels. For $\mathrm{4Al(s) + 3O_{2}(g) \rightarrow 2Al_{2}O_{3}(s)}$: particles — 4 atoms of Al react with 3 molecules of $\mathrm{O_{2}}$ to give 2 formula units of $\mathrm{Al_{2}O_{3}}$; moles — 4 mol Al with 3 mol $\mathrm{O_{2}}$ give 2 mol $\mathrm{Al_{2}O_{3}}$; masses — $108\ \mathrm{g}$ of Al with $96\ \mathrm{g}$ of $\mathrm{O_{2}}$ give $204\ \mathrm{g}$ of $\mathrm{Al_{2}O_{3}}$. The moles go from 7 to 2, but the mass stays at $204\ \mathrm{g}$, exactly as Principle 1.10 says.
To balance $\mathrm{H_{2}(g) + O_{2}(g) \rightarrow H_{2}O(l)}$, a student writes $\mathrm{H_{2}(g) + O_{2}(g) \rightarrow H_{2}O_{2}(l)}$. What is wrong?
Mole ratios: mass–mass and mass–volume relations
Because a coefficient counts particles, and a mole is a fixed number of particles, the coefficients of a balanced equation are also the ratios of the amounts (in moles) that react and form. Masses do not have this property — $1\ \mathrm{g}$ of hydrogen and $1\ \mathrm{g}$ of oxygen contain very different numbers of molecules — which is why every stoichiometric calculation goes through moles.
Stoichiometry is the calculation of the quantities (amounts, masses, gas volumes, volumes of solution) of reactants and products in a chemical reaction from its balanced equation.
The mole ratio between two species X and Y in a balanced equation is $\nu_{\mathrm{X}}:\nu_{\mathrm{Y}}$, the ratio of their coefficients. The extent of reaction $\xi$ ("xi", unit mol) measures how far the reaction has gone: when the reaction has advanced by $\xi$, each reactant has lost $\nu\,\xi$ moles and each product has gained $\nu\,\xi$ moles.
For a reaction $a\,\mathrm{A} + b\,\mathrm{B} \rightarrow c\,\mathrm{C} + d\,\mathrm{D}$ that goes to completion as written, the amounts that react and form satisfy
$$\frac{n_{\mathrm{A}}}{a}=\frac{n_{\mathrm{B}}}{b}=\frac{n_{\mathrm{C}}}{c}=\frac{n_{\mathrm{D}}}{d}=\xi .$$So $n_{\mathrm{C}}=\dfrac{c}{a}\,n_{\mathrm{A}}$, and similarly for any pair. The amounts are converted from and to measured quantities by
$$n=\frac{m}{M}\ \ (\text{mass}),\qquad n=\frac{N}{N_{A}}\ \ (\text{particles}),\qquad n=\frac{pV}{RT}\ \ (\text{ideal gas}),\qquad n=\frac{V}{22.4\ \mathrm{L\,mol^{-1}}}\ \ (\text{gas at STP}).$$For gases at the same temperature and pressure, volumes are proportional to moles, so the coefficients also give the volume ratio of the gases (Gay-Lussac's law of gaseous volumes). This is never true for solids or liquids, and liquid water at STP is not a gas.
The ideal-gas equation $pV=nRT$ is used here only as a tool for converting a gas volume into moles; the gas laws themselves are not part of the JEE Main list. Note the two common values of the molar volume: $22.4\ \mathrm{L\,mol^{-1}}$ at $273.15\ \mathrm{K}$ and $1\ \mathrm{atm}$ (the older STP still used in most JEE problems), and $22.7\ \mathrm{L\,mol^{-1}}$ at $273.15\ \mathrm{K}$ and $1\ \mathrm{bar}$ (the current IUPAC standard). Use the one the question gives.
- Write the balanced equation (with state symbols).
- Convert what you are given into moles of that substance.
- Cross the bridge with the mole ratio: $n_{\mathrm{Y}}=\dfrac{\nu_{\mathrm{Y}}}{\nu_{\mathrm{X}}}\,n_{\mathrm{X}}$.
- Convert moles of the wanted substance into the quantity asked for (mass, volume, particles, volume of solution).
- Check: does the total mass balance? Is the order of magnitude sensible? Are the units right?
In $\mathrm{2C_{2}H_{6}(g) + 7O_{2}(g)}$ $\mathrm{\rightarrow 4CO_{2}(g) + 6H_{2}O(l)}$, $3.0\ \mathrm{mol}$ of $\mathrm{O_{2}}$ react completely. How many moles of $\mathrm{CO_{2}}$ form?
Limiting reagent, percentage yield and purity
In a laboratory or a factory the reactants are rarely mixed in exactly the ratio of the equation. A sandwich shop with 20 slices of bread and 7 slices of cheese can make only 7 cheese sandwiches (2 bread + 1 cheese each), however much bread is left over: the cheese "limits" the output. Reactions behave the same way.
When reactants are not present in the exact stoichiometric ratio, the reaction stops when one of them is used up. That reactant is the limiting reagent (limiting reactant); it fixes the maximum amount of every product. The other reactants are excess reagents: some of each is left over when the reaction stops.
For a reaction that goes to completion, divide the available amount of each reactant by its coefficient. The reactant with the smallest value of $n_{i}/\nu_{i}$ is the limiting reagent, and that smallest value is the extent of reaction actually reached:
$$\xi_{\max}=\min\left(\frac{n_{\mathrm{A}}}{a},\ \frac{n_{\mathrm{B}}}{b},\ \dots\right),\qquad n(\text{product P})=\nu_{\mathrm{P}}\,\xi_{\max},\qquad n(\text{excess reagent left})=n_{j}-\nu_{j}\,\xi_{\max}.$$If all the ratios are equal, the mixture is stoichiometric and nothing is left over. Comparing masses, or comparing moles without dividing by the coefficients, does not identify the limiting reagent.
Even with the limiting reagent identified, the amount of product actually collected is usually less than the calculated maximum. Some reactions stop at equilibrium before completion (esterification is a classic example), side reactions turn some reactant into unwanted products, and product is lost in filtering, transferring and purifying. Two numbers describe this.
The theoretical yield is the amount (or mass) of product calculated from the limiting reagent, assuming complete reaction with no losses. The actual yield is the amount really obtained. The percentage yield is
$$\text{percentage yield}=\frac{\text{actual yield}}{\text{theoretical yield}}\times100\,\%.$$A sample that contains a substance mixed with impurities has percentage purity
$$\text{percentage purity}=\frac{\text{mass of the pure substance in the sample}}{\text{mass of the sample}}\times100\,\%.$$Unless told otherwise, assume the impurities do not take part in the reaction.
Use these in the right direction. Yield acts on the product side: actual product $=\tfrac{\text{yield}}{100}\times$ theoretical. Purity acts on the reactant side: pure reactant $=\tfrac{\text{purity}}{100}\times$ sample mass. When working backwards (how much raw material for a target product?), you divide by both fractions, so the answer gets larger — a quick check that you have not multiplied by mistake.
In the lab below choose $\mathrm{N_{2} + 3H_{2} \rightarrow 2NH_{3}}$ with $4.0\ \mathrm{mol}$ of $\mathrm{N_{2}}$ and $9.0\ \mathrm{mol}$ of $\mathrm{H_{2}}$. What happens?
Equal masses of $\mathrm{H_{2}}$ and $\mathrm{O_{2}}$ are mixed and ignited: $\mathrm{2H_{2}(g) + O_{2}(g) \rightarrow 2H_{2}O(l)}$. Which is the limiting reagent?
Sequential and parallel reactions; reactions in solution
Real processes seldom consist of one equation. Nitric acid is made from ammonia in three steps; coal burning in a poor air supply gives both carbon monoxide and carbon dioxide; a piece of brass dissolving in acid releases gas from two metals at once. Stoichiometry handles all of these with the same mole ratios — we only have to follow each atom along its route.
Reactions are sequential (consecutive) when a product of one step is a reactant of the next: $\mathrm{A \rightarrow B}$, then $\mathrm{B \rightarrow C}$. The species formed and then used up ($\mathrm{B}$) is an intermediate.
Reactions are parallel (simultaneous, competing) when one reactant takes part in two or more reactions at the same time ($\mathrm{A \rightarrow B}$ and $\mathrm{A \rightarrow C}$), or when the components of a mixture each react with the same reagent.
For steps carried out one after another, with the whole of each product passed to the next step:
- Chain the mole ratios: $n(\mathrm{C})=n(\mathrm{A})\times\dfrac{\nu_{\mathrm{B}}}{\nu_{\mathrm{A}}}\Big|_{\text{step 1}}\times\dfrac{\nu_{\mathrm{C}}}{\nu_{\mathrm{B}}}\Big|_{\text{step 2}}$; or, equivalently, multiply the step equations so that each intermediate has the same coefficient where it is formed and where it is used, add them and cancel it, giving an overall equation.
- Yields multiply: the overall fractional yield is the product of the step yields, $Y=Y_{1}Y_{2}Y_{3}\cdots$ (so $90\,\%$ and $80\,\%$ give $72\,\%$, never $85\,\%$ or $170\,\%$).
- If an intermediate formed in a later step is recycled to an earlier one, the overall ratio changes; follow the key atom instead (Principle 1.14).
Parallel reactions need one more piece of information than the equations: how the reactant is shared between the routes. In a mixture problem the shares are unknown amounts $x$ and $y$; two independent facts — usually a total mass and a total amount of gas or reagent — give two equations. When the shares are set by a shortage of one reagent, as when carbon burns in limited oxygen, they follow from limiting-reagent reasoning applied step by step. Interactive 2 shows this case: carbon is first burnt to CO, and only the oxygen left after that converts CO to $\mathrm{CO_{2}}$.
$1.0\ \mathrm{mol}$ of carbon is burnt in $0.75\ \mathrm{mol}$ of oxygen until either is used up. What is in the reactor afterwards?
The bars of Interactive 2 suggest a shortcut that often saves writing any equation at all. However many steps or routes there are, atoms of each element are only moved around, so the total amount of each element is the same before and after.
In any set of chemical reactions (sequential, parallel, or both), the total amount of atoms of each element is unchanged. For an element X distributed among compounds,
$$\sum_{\text{reactants}} (\text{atoms of X per formula})\times n=\sum_{\text{products}} (\text{atoms of X per formula})\times n .$$Example: if all the carbon of $1.00\ \mathrm{mol}$ of $\mathrm{C}$ ends up as CO and $\mathrm{CO_{2}}$, then $n(\mathrm{CO})+n(\mathrm{CO_{2}})=1.00\ \mathrm{mol}$; if $0.80\ \mathrm{mol}$ of $\mathrm{O_{2}}$ is all used, the oxygen atoms give $n(\mathrm{CO})+2n(\mathrm{CO_{2}})=1.60\ \mathrm{mol}$. Hence $n(\mathrm{CO_{2}})=0.60$, $n(\mathrm{CO})=0.40\ \mathrm{mol}$ — with no equation written. POAC works for the conserved element in each route; it gives no information about which route was taken unless enough elements are balanced.
Many reactions in the laboratory happen in solution, where we measure volumes, not masses. Here we need only one concentration term as a tool: the molarity $M$, the amount of solute per litre of solution, in $\mathrm{mol\,L^{-1}}$ (written M). It is studied with the other concentration terms in Section 5.1.
The amount of solute in a volume $V$ of a solution of molarity $M$ is
$$n=M\times V\quad(V\ \text{in litres});\qquad n\ (\mathrm{mmol})=M\times V\ (\mathrm{mL}).$$For $a\,\mathrm{A}(aq) + b\,\mathrm{B}(aq) \rightarrow$ products, the two solutions react exactly (neither in excess) when
$$\frac{M_{\mathrm{A}}V_{\mathrm{A}}}{a}=\frac{M_{\mathrm{B}}V_{\mathrm{B}}}{b}.$$If they are not in this ratio, the smaller of $M_{\mathrm{A}}V_{\mathrm{A}}/a$ and $M_{\mathrm{B}}V_{\mathrm{B}}/b$ identifies the limiting reagent (Rule 1.12), and the concentration of anything left over is its amount divided by the total volume of the mixture (volumes assumed additive).
A common JEE pattern is the back titration: an insoluble or slow-reacting solid (limestone, an antacid tablet) is treated with a known excess of acid; the acid left over is then measured by titration with a base. The acid used by the solid is the difference. For example, if a solid consumes the acid in $\mathrm{CaCO_{3} + 2HCl}$ and $50.0\ \mathrm{mmol}$ HCl was added while $10.0\ \mathrm{mmol}$ remained, the solid took $40.0\ \mathrm{mmol}$ HCl, i.e. $20.0\ \mathrm{mmol}$ $\mathrm{CaCO_{3}}$.
1. Limiting reagent by mass or by raw moles. The test is the smallest $n/\nu$. In $\mathrm{N_{2} + 3H_{2}}$, $5$ mol $\mathrm{H_{2}}$ is limiting against $2$ mol $\mathrm{N_{2}}$ — more moles, yet limiting.
2. An unbalanced (or wrongly balanced) equation. Every ratio comes from the coefficients; check atoms and charge before you calculate. Remember $\mathrm{H_{2}}$, $\mathrm{O_{2}}$, $\mathrm{N_{2}}$, $\mathrm{Cl_{2}}$ are diatomic: $M(\mathrm{H_{2}})=2$, not 1.
3. Gas volumes. Coefficients give volume ratios only for gases at the same $T$ and $p$; liquid water and solids have no "22.4 L". Use $22.4$ or $22.7\ \mathrm{L\,mol^{-1}}$ as the problem states, and $pV=nRT$ (with $T$ in kelvin) at any other conditions.
4. Yield and purity the wrong way round. Going forward (reactant → product) you multiply by the fractions; going backward (product → raw material) you divide. In multistep syntheses the yields multiply.
5. Millilitres and the mixed volume. $n=MV$ needs $V$ in litres (or gives mmol with mL). After mixing two solutions, a leftover concentration uses the total volume.
How many millilitres of $0.10\ \mathrm{M}$ HCl react exactly with $25.0\ \mathrm{mL}$ of $0.20\ \mathrm{M}$ $\mathrm{Na_{2}CO_{3}}$ in $\mathrm{Na_{2}CO_{3}(aq) + 2HCl(aq)}$ $\mathrm{\rightarrow 2NaCl(aq) + H_{2}O(l) + CO_{2}(g)}$?
Exercises
Use the molar masses listed at the start of the section, $V_{m}=22.4\ \mathrm{L\,mol^{-1}}$ at STP and $R=0.0821\ \mathrm{L\,atm\,mol^{-1}\,K^{-1}}$. Assume reactions go to completion and impurities are inert unless a part says otherwise.
- 1 Balance $\mathrm{C_{3}H_{8}(g) + O_{2}(g) \rightarrow CO_{2}(g) + H_{2}O(l)}$ and give the sum of the smallest whole-number coefficients.
- 2 Balance $\mathrm{Fe(s) + H_{2}O(g) \rightarrow Fe_{3}O_{4}(s) + H_{2}(g)}$.
- 3 Balance $\mathrm{NH_{3}(g) + O_{2}(g) \rightarrow NO(g) + H_{2}O(g)}$.
- 4 Balance $\mathrm{Al_{2}(SO_{4})_{3}(aq) + NaOH(aq)}$ $\mathrm{\rightarrow Al(OH)_{3}(s) + Na_{2}SO_{4}(aq)}$ and give the sum of the coefficients.
- 5 Balance $\mathrm{C_{2}H_{5}OH(l) + O_{2}(g)}$ $\mathrm{\rightarrow CO_{2}(g) + H_{2}O(l)}$.
- 6 Balance $\mathrm{Ca(OH)_{2}(aq) + H_{3}PO_{4}(aq)}$ $\mathrm{\rightarrow Ca_{3}(PO_{4})_{2}(s) + H_{2}O(l)}$.
- 7 In $\mathrm{2C_{4}H_{10}(g) + 13O_{2}(g)}$ $\mathrm{\rightarrow 8CO_{2}(g) + 10H_{2}O(l)}$, how many moles of $\mathrm{O_{2}}$ are needed per mole of butane, and how many moles of water form from $0.50\ \mathrm{mol}$ of butane?
- 8 For $\mathrm{4Al(s) + 3O_{2}(g) \rightarrow 2Al_{2}O_{3}(s)}$, find the mass of $\mathrm{O_{2}}$ that reacts with $108\ \mathrm{g}$ of Al, and show that mass is conserved although the number of moles is not.
- 1 What mass of $\mathrm{CO_{2}}$ is released when $25.0\ \mathrm{g}$ of $\mathrm{CaCO_{3}}$ is heated strongly, $\mathrm{CaCO_{3}(s) \xrightarrow{\Delta} CaO(s) + CO_{2}(g)}$?
- 2 What volume does the $\mathrm{CO_{2}}$ of part 1 occupy at STP?
- 3 Find the masses of $\mathrm{O_{2}}$ consumed and of water formed when $8.0\ \mathrm{g}$ of methane burns completely.
- 4 What mass of $\mathrm{KClO_{3}}$ must be decomposed, $\mathrm{2KClO_{3}(s)}$ $\mathrm{\xrightarrow[\Delta]{MnO_{2} } 2KCl(s) + 3O_{2}(g)}$, to obtain $6.72\ \mathrm{L}$ of $\mathrm{O_{2}}$ at STP?
- 5 What mass of zinc gives $2.24\ \mathrm{L}$ of $\mathrm{H_{2}}$ at STP with excess dilute sulphuric acid?
- 6 In the thermite reaction $\mathrm{2Al(s) + Fe_{2}O_{3}(s)}$ $\mathrm{\rightarrow Al_{2}O_{3}(s) + 2Fe(l)}$, find the mass of Al needed for $80.0\ \mathrm{g}$ of $\mathrm{Fe_{2}O_{3}}$ and the mass of iron formed.
- 7 What volume of air (21 % $\mathrm{O_{2}}$ by volume) is needed to burn $1.00\ \mathrm{L}$ of propane completely, both measured at the same temperature and pressure?
- 8 $10.7\ \mathrm{g}$ of $\mathrm{NH_{4}Cl}$ is heated with excess slaked lime: $\mathrm{2NH_{4}Cl(s) + Ca(OH)_{2}(s)}$ $\mathrm{\rightarrow CaCl_{2}(s) + 2NH_{3}(g) + 2H_{2}O(g)}$. What volume of ammonia is obtained at $27\,^{\circ}\mathrm{C}$ and $2.00\ \mathrm{atm}$?
- 1 $4.0\ \mathrm{g}$ of $\mathrm{H_{2}}$ and $16.0\ \mathrm{g}$ of $\mathrm{O_{2}}$ are exploded together. Which is limiting, what mass of water forms, and what mass of which gas is left?
- 2 $5.40\ \mathrm{g}$ of Al is heated in $14.2\ \mathrm{g}$ of $\mathrm{Cl_{2}}$: $\mathrm{2Al(s) + 3Cl_{2}(g) \rightarrow 2AlCl_{3}(s)}$. Find the mass of $\mathrm{AlCl_{3}}$ formed and the mass of the excess reactant left.
- 3 $2.40\ \mathrm{g}$ of magnesium ribbon is added to $100\ \mathrm{mL}$ of $1.00\ \mathrm{M}$ HCl. What volume of $\mathrm{H_{2}}$ (STP) is evolved, and what mass of Mg remains?
- 4 Heating $10.0\ \mathrm{g}$ of $\mathrm{CaCO_{3}}$ gives $3.92\ \mathrm{g}$ of CaO. Find the percentage yield.
- 5 $6.0\ \mathrm{g}$ of ethanoic acid is heated with excess ethanol and a little concentrated $\mathrm{H_{2}SO_{4}}$: $\mathrm{CH_{3}COOH(l) + C_{2}H_{5}OH(l)}$ $\mathrm{\rightleftharpoons CH_{3}COOC_{2}H_{5}(l) + H_{2}O(l)}$. $5.28\ \mathrm{g}$ of ethyl ethanoate is isolated. Find the percentage yield and give one reason why it is below 100 %.
- 6 What volume of $\mathrm{CO_{2}}$ at STP is obtained from $20.0\ \mathrm{g}$ of limestone that is $90.0\,\%$ $\mathrm{CaCO_{3}}$, with excess acid?
- 7 A $5.00\ \mathrm{g}$ sample of impure zinc gives $1.344\ \mathrm{L}$ of $\mathrm{H_{2}}$ at STP with excess acid. Find the percentage purity of the zinc.
- 8 (Industry) What mass of limestone of $80.0\,\%$ purity must be burnt to obtain $28.0\ \mathrm{kg}$ of quicklime, CaO, if the process yield is $90.0\,\%$?
- 9 $10.0\ \mathrm{g}$ each of $\mathrm{H_{2}}$ and $\mathrm{O_{2}}$ are reacted. Which is limiting and what mass of water forms? Why is "the gas with the smaller mass" not a valid test here?
- 1 In the contact process, $\mathrm{S(s) + O_{2}(g) \rightarrow SO_{2}(g)}$, $\mathrm{2SO_{2}(g) + O_{2}(g) \rightarrow 2SO_{3}(g)}$, and (overall) $\mathrm{SO_{3}(g) + H_{2}O(l) \rightarrow H_{2}SO_{4}(l)}$. What mass of $\mathrm{H_{2}SO_{4}}$ can be made from $1.60\ \mathrm{kg}$ of sulphur if every step is complete?
- 2 Repeat part 1 if the oxidation of $\mathrm{SO_{2}}$ has a $96.0\,\%$ yield and the other steps are complete.
- 3 (Airbag) The sodium formed from $\mathrm{2NaN_{3}(s) \rightarrow 2Na(s) + 3N_{2}(g)}$ is removed by $\mathrm{10Na(s) + 2KNO_{3}(s)}$ $\mathrm{\rightarrow K_{2}O(s) + 5Na_{2}O(s) + N_{2}(g)}$. For $130\ \mathrm{g}$ of $\mathrm{NaN_{3}}$, find the total amount of $\mathrm{N_{2}}$, its volume at $27\,^{\circ}\mathrm{C}$ and $1.00\ \mathrm{atm}$, and the mass of $\mathrm{KNO_{3}}$ needed.
- 4 $1.00\ \mathrm{mol}$ of carbon burns in $0.80\ \mathrm{mol}$ of $\mathrm{O_{2}}$; both are completely consumed and the products are CO and $\mathrm{CO_{2}}$. Use atom conservation to find the amount of each.
- 5 A $10.0\ \mathrm{g}$ mixture of $\mathrm{Na_{2}CO_{3}}$ and $\mathrm{NaHCO_{3}}$ loses $1.24\ \mathrm{g}$ on strong heating, $\mathrm{2NaHCO_{3}(s)}$ $\mathrm{\xrightarrow{\Delta} Na_{2}CO_{3}(s) + H_{2}O(g) + CO_{2}(g)}$ ($\mathrm{Na_{2}CO_{3}}$ is stable). Find the percentage of $\mathrm{NaHCO_{3}}$ by mass.
- 6 What volume of $0.200\ \mathrm{M}$ $\mathrm{AgNO_{3}}$ precipitates all the chloride from $25.0\ \mathrm{mL}$ of $0.100\ \mathrm{M}$ $\mathrm{BaCl_{2}}$, and what mass of AgCl forms?
- 7 $50.0\ \mathrm{mL}$ of $0.40\ \mathrm{M}$ $\mathrm{H_{2}SO_{4}}$ is mixed with $50.0\ \mathrm{mL}$ of $0.60\ \mathrm{M}$ NaOH. Find the amount of $\mathrm{Na_{2}SO_{4}}$ formed and the molarity of the reactant left over in the mixture.
- 8 The carbon in a $1.00\ \mathrm{g}$ steel sample is burnt to $\mathrm{CO_{2}}$, which is absorbed in excess $\mathrm{Ba(OH)_{2}}$ solution, giving $0.197\ \mathrm{g}$ of $\mathrm{BaCO_{3}}$. Find the percentage of carbon in the steel.
E1. JEE Main · MCQ When the equation $a\,\mathrm{C_{2}H_{6}(g)} + b\,\mathrm{O_{2}(g)}$ $\rightarrow c\,\mathrm{CO_{2}(g)} + d\,\mathrm{H_{2}O(l)}$ is balanced with the smallest whole numbers, $a+b+c+d$ equals (A) $15$ (B) $19$ (C) $17$ (D) $21$
E2. JEE Main · Numerical $4.0\ \mathrm{g}$ of hydrogen is ignited with $40.0\ \mathrm{g}$ of oxygen. The mass of water formed, in grams, is ______. (Molar masses: H 1, O 16.) Give the answer to the nearest integer.
E3. JEE Main · MCQ Equal masses of magnesium and oxygen are heated together until reaction is complete: $\mathrm{2Mg(s) + O_{2}(g) \rightarrow 2MgO(s)}$. Which statement is correct? (A) Magnesium is in excess (B) Oxygen is the limiting reagent (C) One-third of the oxygen remains unreacted (D) The mass of MgO formed equals the total mass taken
E4. JEE Main · Numerical A $2.50\ \mathrm{g}$ sample of impure calcium carbonate is dissolved in $50.0\ \mathrm{mL}$ of $1.00\ \mathrm{M}$ HCl (excess). The unreacted acid needs $10.0\ \mathrm{mL}$ of $1.00\ \mathrm{M}$ NaOH for neutralisation. Assuming the impurities do not react with acid, the percentage purity of the sample is ______. Give the answer to the nearest integer.
E5. JEE Main · MCQ White phosphorus is converted to phosphoric acid in two steps: $\mathrm{P_{4}(s) + 5O_{2}(g) \rightarrow P_{4}O_{10}(s)}$ with $80\,\%$ yield, then $\mathrm{P_{4}O_{10}(s) + 6H_{2}O(l) \rightarrow 4H_{3}PO_{4}(aq)}$ with $75\,\%$ yield. The mass of $\mathrm{H_{3}PO_{4}}$ obtained from $12.4\ \mathrm{g}$ of $\mathrm{P_{4}}$ is (A) $39.2\ \mathrm{g}$ (B) $31.4\ \mathrm{g}$ (C) $29.4\ \mathrm{g}$ (D) $23.5\ \mathrm{g}$
E6. JEE Main · Numerical $20\ \mathrm{mL}$ of a mixture of methane and ethane needs exactly $55\ \mathrm{mL}$ of oxygen for complete combustion, all volumes measured at the same temperature and pressure. The percentage of methane by volume in the mixture is ______. Give the answer to the nearest integer.
Research question. Can a kitchen reaction reveal its own limiting reagent? How does the mass of carbon dioxide released by baking soda and vinegar depend on the amount of baking soda — and how close does it come to the theoretical yield?
Why it matters. Chemical and pharmaceutical plants are judged by yield and by how much waste they make per kilogram of product (the "E-factor" of green chemistry). A drug made in eight steps at 80 % each delivers only about 17 % overall, so process chemists around the world spend years raising the yield of single steps. The same logic — limiting reagent, losses, purity — sets the cost of fertilisers, cement and steel.
What to do.
- Pour $50\ \mathrm{mL}$ of vinegar (about 4–5 % ethanoic acid; read the label) into each of six cups. Weigh each cup with its vinegar on a kitchen balance (0.01 g if possible).
- Add $0.5, 1.0, 1.5, 2.0, 3.0$ and $4.0\ \mathrm{g}$ of sodium hydrogencarbonate to the cups, one each; stir gently until fizzing stops (about 10 minutes) and weigh again. The loss is the $\mathrm{CO_{2}}$ released: $\mathrm{NaHCO_{3}(s) + CH_{3}COOH(aq)}$ $\mathrm{\rightarrow CH_{3}COONa(aq) + H_{2}O(l) + CO_{2}(g)}$.
- Plot mass lost against mass of $\mathrm{NaHCO_{3}}$. You should see a rising line that levels off — the kink of Interactive 1. Read off where it bends and use it to estimate the amount of ethanoic acid in $50\ \mathrm{mL}$ of vinegar.
- For the points before the kink, compute the theoretical mass of $\mathrm{CO_{2}}$ ($\tfrac{44}{84}$ of the baking-soda mass) and the percentage yield. Compare your acid estimate with the label.
Tools: Kitchen balance, measuring cylinder or syringe, six cups, teaspoon, spreadsheet.
Hand in: Your table and graph, the position of the kink, your estimate of the percentage of ethanoic acid in the vinegar, and two sentences on why the yields are below 100 %.
Going further. Some $\mathrm{CO_{2}}$ stays dissolved in the liquid. Repeat one point with warm vinegar, or wait an extra 20 minutes: does the yield rise? How would you correct the acid estimate for dissolved gas?
🧪 Self-check quiz
Q1. $3.0\ \mathrm{mol}$ of $\mathrm{SO_{2}}$ and $2.0\ \mathrm{mol}$ of $\mathrm{O_{2}}$ react completely according to $\mathrm{2SO_{2}(g) + O_{2}(g) \rightarrow 2SO_{3}(g)}$. Which is correct?
Q2. Which quantity is not necessarily the same on both sides of a balanced chemical equation?
Q3. The volume of $\mathrm{CO_{2}}$ at STP ($22.4\ \mathrm{L\,mol^{-1}}$) formed by complete combustion of $0.50\ \mathrm{mol}$ of propane is
Q4. The volume of $0.50\ \mathrm{M}$ $\mathrm{H_{2}SO_{4}}$ that exactly neutralises $20.0\ \mathrm{mL}$ of $1.0\ \mathrm{M}$ NaOH is
Q5. A three-step synthesis has step yields of $90\,\%$, $80\,\%$ and $50\,\%$. The overall yield is