Chapter 5 · Solutions

5.2 Vapour Pressure and Raoult's Law

Every liquid sends molecules into the space above it until the vapour reaches a fixed pressure. In a mixture of two liquids each component contributes in proportion to its mole fraction — Raoult's law — and the vapour is always richer in the more volatile one. When the two kinds of molecule attract each other more or less strongly than their own kind, the law fails in a predictable way, and azeotropes appear.

Open a bottle of perfume and within seconds the scent fills the room; open a bottle of glycerol and nothing happens. Leave a saucer of petrol and a saucer of water side by side and the petrol is gone long before the water. Liquids differ in how eagerly their molecules escape into the gas above them, and the measure of that eagerness is the vapour pressure. It decides how fast a liquid evaporates, at what temperature it boils, and — when two liquids are mixed — what the vapour above the mixture is made of.

That last point is the basis of distillation, one of the oldest and most important operations in chemistry: crude oil is split into petrol, kerosene and diesel, liquid air into nitrogen and oxygen, and fermented sugar solutions into spirits, all because the vapour over a liquid mixture is richer in its more volatile component. Yet no amount of distillation turns a dilute ethanol–water mixture into pure ethanol: the process stops at about $95.6\%$ ethanol. In this section we build the theory that explains both facts — Raoult's law for ideal solutions, Dalton's law for the vapour, the vapour pressure–composition diagram, and the deviations of real solutions that lead to azeotropes. We use mole fractions from Section 5.1; the lowering of vapour pressure by a non-volatile solute is developed into the colligative properties in Section 5.3.

Vapour pressure of a liquid

Molecules in a liquid have a spread of kinetic energies. At the surface, the most energetic ones can break free of their neighbours' attractions and escape: the liquid evaporates. In an open dish they drift away and the liquid slowly disappears. In a closed container they cannot leave; they collide with the walls and with the liquid surface, and some are recaptured — they condense. As the vapour builds up, the rate of condensation grows until it equals the rate of evaporation. From then on the amount of vapour stays constant, although molecules keep crossing the surface in both directions: a dynamic equilibrium,

$$\mathrm{liquid} \rightleftharpoons \mathrm{vapour}.$$
📘 Definition 5.6 — Vapour pressure and boiling point

The vapour pressure of a liquid at a given temperature is the pressure exerted by its vapour when the vapour is in dynamic equilibrium with the liquid. We write $p^{\circ}$ for the vapour pressure of a pure liquid. It depends only on the nature of the liquid and on the temperature; it does not depend on the amount of liquid, on the area of its surface or on the volume of the container, as long as some liquid remains.

A liquid boils when its vapour pressure equals the external pressure: bubbles of vapour can then form and grow inside the liquid. The normal boiling point is the boiling temperature under an external pressure of $1\ \mathrm{atm}$ ($101.3\ \mathrm{kPa}$); the standard boiling point refers to $1\ \mathrm{bar}$ ($100\ \mathrm{kPa}$). For water they are $100\ ^{\circ}\mathrm{C}$ and $99.6\ ^{\circ}\mathrm{C}$.

Nature of the liquid. The weaker the attractions between its molecules, the more easily they escape, and the higher the vapour pressure. Diethyl ether, held together only by dipole and dispersion forces, has a vapour pressure of about $59\ \mathrm{kPa}$ at $20\ ^{\circ}\mathrm{C}$; ethanol, whose molecules are hydrogen bonded, only about $5.9\ \mathrm{kPa}$; glycerol, with three OH groups per molecule, practically none. A liquid with a high vapour pressure is called volatile, and it has a low boiling point.

Temperature. Raising the temperature increases the fraction of molecules energetic enough to escape, so the vapour pressure rises — and it rises steeply, not in proportion to the temperature:

Temperature / °C2025406080100
Vapour pressure of water / kPa2.343.177.3819.947.4101.3

The table also explains cooking at altitude: on a mountain where the air pressure is $70\ \mathrm{kPa}$, water boils when its vapour pressure reaches $70\ \mathrm{kPa}$, at about $90\ ^{\circ}\mathrm{C}$, and food takes longer to cook. A pressure cooker does the opposite.

✏️ Example 1 — Water in a sealed flask
$1.00\ \mathrm{g}$ of water is sealed into an evacuated $10.0\ \mathrm{L}$ flask at $25\ ^{\circ}\mathrm{C}$, where the vapour pressure of water is $3.17\ \mathrm{kPa}$. (a) What mass of water evaporates, and what is the pressure in the flask at equilibrium? (b) Repeat for a $20.0\ \mathrm{L}$ flask. (c) What is the smallest flask in which all the water would evaporate? Treat the vapour as an ideal gas, neglect the volume of the liquid, and take $R=8.314\ \mathrm{J\,mol^{-1}\,K^{-1}}$, $M(\mathrm{H_{2}O})=18.0\ \mathrm{g\,mol^{-1}}$.
(a) If liquid remains, the vapour is at $3.17\ \mathrm{kPa}$. Amount of vapour: $n=\dfrac{pV}{RT}=\dfrac{3170\times0.0100}{8.314\times298.15}=0.01279\ \mathrm{mol}=0.230\ \mathrm{g}$. This is less than $1.00\ \mathrm{g}$, so liquid does remain ($0.770\ \mathrm{g}$) and the pressure is $3.17\ \mathrm{kPa}$.
(b) Twice the volume holds twice the vapour at the same pressure: $0.460\ \mathrm{g}$ evaporates, and the pressure is still $3.17\ \mathrm{kPa}$ — the vapour pressure does not depend on the size of the container.
(c) All $\dfrac{1.00}{18.0}=0.0556\ \mathrm{mol}$ as vapour at $3.17\ \mathrm{kPa}$: $V=\dfrac{nRT}{p}=\dfrac{0.0556\times8.314\times298.15}{3170}=0.0434\ \mathrm{m^{3}}=43.4\ \mathrm{L}$. In a larger flask the water all evaporates and the pressure is below $3.17\ \mathrm{kPa}$ (no liquid, no equilibrium).

A closed vessel contains liquid hexane in equilibrium with its vapour at $25\ ^{\circ}\mathrm{C}$. A piston slowly halves the volume of the vapour space, keeping the temperature at $25\ ^{\circ}\mathrm{C}$. When equilibrium is restored, the pressure of the hexane vapour is

Raoult's law for a mixture of volatile liquids

Now mix two volatile liquids that dissolve in each other completely — benzene and toluene, say. Both kinds of molecule are present at the surface, and both escape. The vapour is a mixture whose total pressure is the sum of the partial pressures of the two components. How large is each?

Think about component 1. In the pure liquid its molecules occupy the whole surface. In the solution only a fraction $x_{1}$ of the surface molecules are of kind 1, so — if a molecule of kind 1 escapes just as easily from a surrounding of kind-2 molecules as from its own kind — the rate of escape, and with it the equilibrium partial pressure, is reduced to the fraction $x_{1}$ of the pure value.

📐 Law 5.4 — Raoult's law

For a solution of volatile liquids, the partial vapour pressure of each component is equal to its mole fraction in the liquid multiplied by the vapour pressure of the pure component at the same temperature:

$$p_{1}=x_{1}\,p_{1}^{\circ},\qquad p_{2}=x_{2}\,p_{2}^{\circ}.$$

By Dalton's law of partial pressures the total vapour pressure is $p=p_{1}+p_{2}$; with $x_{2}=1-x_{1}$,

$$p=p_{2}^{\circ}+\left(p_{1}^{\circ}-p_{2}^{\circ}\right)x_{1}.$$

Conditions: the law holds exactly over the whole composition range only for ideal solutions (Definition 5.7), in which the attractions between unlike molecules are the same as those between like molecules; real solutions obey it closely only when the attractions are similar. For any solution, the component present in large excess (the solvent, $x_{1}\rightarrow1$) obeys Raoult's law. $x_{1},x_{2}$ are mole fractions in the liquid; all pressures are at one temperature.

So for an ideal solution each partial pressure is a straight line through the origin of a plot against $x_{1}$, and the total vapour pressure is a straight line joining $p_{2}^{\circ}$ (at $x_{1}=0$) to $p_{1}^{\circ}$ (at $x_{1}=1$). The total vapour pressure of the solution always lies between the vapour pressures of the two pure liquids.

A non-volatile solute. If component 2 is a solid such as glucose or urea, its vapour pressure is negligible, $p_{2}^{\circ}\approx0$, and only the solvent is found in the vapour. Raoult's law then gives the vapour pressure of the solution as

$$p=x_{1}\,p_{1}^{\circ},$$

which is lower than that of the pure solvent, because $x_{1}\lt1$: the solute molecules take up part of the surface without contributing any vapour. This lowering is the first of the colligative properties of Section 5.3.

✏️ Example 2 — Benzene and toluene
At $25\ ^{\circ}\mathrm{C}$ the vapour pressures of pure benzene ($\mathrm{C_{6}H_{6}}$) and pure toluene ($\mathrm{C_{6}H_{5}CH_{3}}$) are $12.8\ \mathrm{kPa}$ and $3.85\ \mathrm{kPa}$. A solution is made from $39.0\ \mathrm{g}$ of benzene and $46.0\ \mathrm{g}$ of toluene; it behaves ideally. Find (a) the partial vapour pressure of each component and (b) the total vapour pressure. (c) Which liquid boils at the lower temperature, and why? ($M$: benzene $78.0$, toluene $92.0\ \mathrm{g\,mol^{-1}}$.)
Moles Benzene $\dfrac{39.0}{78.0}=0.500\ \mathrm{mol}$; toluene $\dfrac{46.0}{92.0}=0.500\ \mathrm{mol}$; so $x_{\mathrm{B}}=x_{\mathrm{T}}=0.500$.
(a) $p_{\mathrm{B}}=0.500\times12.8=6.40\ \mathrm{kPa}$; $p_{\mathrm{T}}=0.500\times3.85=1.93\ \mathrm{kPa}$.
(b) $p=6.40+1.925=8.33\ \mathrm{kPa}$ — between $3.85$ and $12.8\ \mathrm{kPa}$, and, for this equimolar mixture, exactly their average.
(c) Benzene: its higher vapour pressure reaches atmospheric pressure at a lower temperature (normal boiling points $80\ ^{\circ}\mathrm{C}$ against $111\ ^{\circ}\mathrm{C}$). The extra methyl group gives toluene larger dispersion forces.

Liquids A ($p_{\mathrm{A}}^{\circ}=60\ \mathrm{kPa}$) and B ($p_{\mathrm{B}}^{\circ}=20\ \mathrm{kPa}$) form an ideal solution with $x_{\mathrm{A}}=0.25$. The total vapour pressure is

Composition of the vapour; vapour pressure–composition plots

The liquid has composition $x_{1}$; what about the vapour above it? The vapour is a gas mixture, and in a gas mixture the mole fraction of each component equals its share of the total pressure (Dalton's law). We write mole fractions in the vapour as $y_{1},y_{2}$ to keep them apart from those in the liquid.

📐 Result 5.5 — Composition of the vapour over an ideal solution

By Dalton's law $p_{i}=y_{i}\,p$; combining with Raoult's law,

$$y_{1}=\frac{p_{1}}{p}=\frac{x_{1}p_{1}^{\circ}}{x_{1}p_{1}^{\circ}+x_{2}p_{2}^{\circ}},$$ $$\frac{y_{1}}{y_{2}}=\frac{p_{1}^{\circ}}{p_{2}^{\circ}}\cdot\frac{x_{1}}{x_{2}}.$$
  • If $p_{1}^{\circ}\gt p_{2}^{\circ}$, then $\dfrac{y_{1}}{y_{2}}\gt\dfrac{x_{1}}{x_{2}}$: the vapour is richer than the liquid in the more volatile component (the one with the higher vapour pressure).
  • Eliminating $x_{1}$ gives the total pressure in terms of the vapour composition: $$\frac{1}{p}=\frac{y_{1}}{p_{1}^{\circ}}+\frac{y_{2}}{p_{2}^{\circ}}.$$

Conditions: the solution is ideal (obeys Raoult's law) and the vapour behaves as an ideal gas mixture.

The vapour pressure–composition diagram. Plot pressure against mole fraction of component 1 at a fixed temperature. The total vapour pressure as a function of the liquid composition, $p(x_{1})$, is the straight Raoult line (the liquid or bubble-point line). The same pressure as a function of the vapour composition, $p(y_{1})$ from the $1/p$ formula, is a curve that sags below the straight line (the vapour or dew-point line); the two meet at the pure components. A horizontal line at any pressure between them — a tie line — joins a liquid composition to the vapour composition in equilibrium with it, and the vapour end always lies nearer the more volatile component.

Above the liquid line (high pressure) the system is all liquid; below the vapour line it is all vapour; between them liquid and vapour coexist. This diagram is the key to distillation: boil a liquid, collect and condense its vapour — the condensate is richer in the volatile component; boil that, and it is richer still. A fractionating column performs many such evaporation–condensation steps one above another, so the vapour reaching the top is almost pure volatile component and the liquid at the bottom is almost pure involatile component. That is how the components of an ideal (or nearly ideal) solution are separated completely.

🧭 Problem-solving strategy — Raoult and Dalton together
  1. Label liquid mole fractions $x$ and vapour mole fractions $y$, and note which are given.
  2. Liquid known: $p_{i}=x_{i}p_{i}^{\circ}$, then $p=\sum p_{i}$, then $y_{i}=p_{i}/p$.
  3. Vapour known: $1/p=\sum y_{i}/p_{i}^{\circ}$, then $x_{i}=y_{i}p/p_{i}^{\circ}$; or use $\dfrac{x_{1}}{x_{2}}=\dfrac{y_{1}}{y_{2}}\cdot\dfrac{p_{2}^{\circ}}{p_{1}^{\circ}}$.
  4. Total pressures known at two compositions: the line $p=p_{2}^{\circ}+(p_{1}^{\circ}-p_{2}^{\circ})x_{1}$ gives two equations for $p_{1}^{\circ},p_{2}^{\circ}$.
  5. Check: $p$ lies between $p_{1}^{\circ}$ and $p_{2}^{\circ}$, and $y$ of the more volatile component exceeds its $x$.
✏️ Example 3 — One step of distillation
For the equimolar benzene–toluene solution of Example 2 ($p^{\circ}_{\mathrm{B}}=12.8$, $p^{\circ}_{\mathrm{T}}=3.85\ \mathrm{kPa}$ at $25\ ^{\circ}\mathrm{C}$): (a) find the mole fraction of benzene in the vapour. (b) A little of this vapour is condensed and the liquid obtained is brought to equilibrium with its own vapour at $25\ ^{\circ}\mathrm{C}$. Find the total vapour pressure of the condensate and the mole fraction of benzene in its vapour.
(a) $y_{\mathrm{B}}=\dfrac{p_{\mathrm{B}}}{p}=\dfrac{6.40}{8.325}=0.769$. The liquid is $50\%$ benzene; its vapour is $77\%$ benzene.
(b) The condensate has $x_{\mathrm{B}}=0.769$: $p_{\mathrm{B}}=0.769\times12.8=9.84\ \mathrm{kPa}$, $p_{\mathrm{T}}=0.231\times3.85=0.89\ \mathrm{kPa}$, $p=10.73\ \mathrm{kPa}$.
New vapour $y_{\mathrm{B}}=\dfrac{9.84}{10.73}=0.917$. Two evaporation–condensation steps raise benzene from $50\%$ to $92\%$ — a fractionating column simply repeats this many times.
Check $\dfrac{y_{\mathrm{B}}}{y_{\mathrm{T}}}=\dfrac{12.8}{3.85}\cdot\dfrac{x_{\mathrm{B}}}{x_{\mathrm{T}}}$: each step multiplies the benzene : toluene ratio by $3.32$; $1\rightarrow3.32\rightarrow11.0$, i.e. $y_{\mathrm{B}}=\tfrac{11.0}{12.0}=0.917$ ✓.
✏️ Example 4 — Finding the pure-component vapour pressures (JEE level)
Two liquids A and B form an ideal solution. At a certain temperature the total vapour pressure is $52.0\ \mathrm{kPa}$ when $x_{\mathrm{A}}=0.40$ and $68.0\ \mathrm{kPa}$ when $x_{\mathrm{A}}=0.80$. (a) Find $p_{\mathrm{A}}^{\circ}$ and $p_{\mathrm{B}}^{\circ}$. (b) Find the mole fraction of A in the vapour over the first solution.
Find $p_{\mathrm{A}}^{\circ}$ before you open the solution:
Line $52.0=p_{\mathrm{B}}^{\circ}+0.40\,\Delta$ and $68.0=p_{\mathrm{B}}^{\circ}+0.80\,\Delta$ with $\Delta=p_{\mathrm{A}}^{\circ}-p_{\mathrm{B}}^{\circ}$. Subtracting: $0.40\,\Delta=16.0$, so $\Delta=40.0\ \mathrm{kPa}$.
(a) $p_{\mathrm{B}}^{\circ}=52.0-16.0=36.0\ \mathrm{kPa}$ and $p_{\mathrm{A}}^{\circ}=36.0+40.0=76.0\ \mathrm{kPa}$.
(b) $y_{\mathrm{A}}=\dfrac{0.40\times76.0}{52.0}=\dfrac{30.4}{52.0}=0.585$ — richer in A, the more volatile liquid, than the liquid ($0.40$).
Check $x_{\mathrm{A}}=0.80$: $0.80\times76.0+0.20\times36.0=60.8+7.2=68.0\ \mathrm{kPa}$ ✓.
✏️ Example 5 — From the vapour back to the liquid (JEE level)
Liquids A ($p_{\mathrm{A}}^{\circ}=80.0\ \mathrm{kPa}$) and B ($p_{\mathrm{B}}^{\circ}=20.0\ \mathrm{kPa}$) form an ideal solution. The vapour in equilibrium with a certain solution contains equal numbers of moles of A and B. Find (a) the mole fraction of A in the liquid and (b) the total vapour pressure. (c) What is the mole fraction of A in the vapour over a solution with $x_{\mathrm{A}}=0.50$?
Find $x_{\mathrm{A}}$ in the liquid first:
(a) $y_{\mathrm{A}}=y_{\mathrm{B}}$ means $p_{\mathrm{A}}=p_{\mathrm{B}}$: $80.0\,x_{\mathrm{A}}=20.0(1-x_{\mathrm{A}})$, so $x_{\mathrm{A}}=0.200$.
(b) $p=0.200\times80.0+0.800\times20.0=16.0+16.0=32.0\ \mathrm{kPa}$.
Check From the vapour side: $\dfrac1p=\dfrac{0.5}{80.0}+\dfrac{0.5}{20.0}=0.03125$, so $p=32.0\ \mathrm{kPa}$ ✓.
(c) $p=40.0+10.0=50.0\ \mathrm{kPa}$; $y_{\mathrm{A}}=\dfrac{40.0}{50.0}=0.80$. A liquid that is only $20\%$ A gives a $50\%$ vapour, and a $50\%$ liquid gives an $80\%$ vapour.
⏱ Shortcut $\dfrac{x_{\mathrm{A}}}{x_{\mathrm{B}}}=\dfrac{y_{\mathrm{A}}}{y_{\mathrm{B}}}\cdot\dfrac{p_{\mathrm{B}}^{\circ}}{p_{\mathrm{A}}^{\circ}}=1\times\dfrac{20}{80}=\dfrac14$, so $x_{\mathrm{A}}=\dfrac15$.

In the Raoult's-law diagram set $p_{1}^{\circ}=90\ \mathrm{kPa}$, $p_{2}^{\circ}=30\ \mathrm{kPa}$ and $x_{1}=0.50$. What mole fraction of component 1 will the vapour have?

With $p_{1}^{\circ}=90$, $p_{2}^{\circ}=30\ \mathrm{kPa}$ and $x_{1}=0.50$ the readouts show $p_{1}=45.0\ \mathrm{kPa}$, $p_{2}=15.0\ \mathrm{kPa}$, total $p=60.0\ \mathrm{kPa}$ and vapour $y_{1}=0.750$. The tie line at $60\ \mathrm{kPa}$ runs from $x_{1}=0.50$ on the straight liquid line to $y_{1}=0.75$ on the curved vapour line, and the flask on the right shows three red molecules for every blue one in the vapour. The more volatile component is always enriched in the vapour: $\tfrac{y_{1}}{y_{2}}=\tfrac{90}{30}\times\tfrac{0.5}{0.5}=3$. Press Play to watch the tie line slide as $x_{1}$ changes; it shrinks to nothing only at the pure liquids.
Interactive 1 — Raoult's Law: Liquid Line, Vapour Line and Tie Line

An ideal solution of liquids 1 (red) and 2 (blue) at a fixed temperature. Choose the pure vapour pressures and the liquid composition $x_{1}$. The graph shows the partial pressures (thin red and blue lines), the total vapour pressure against the liquid composition (black, straight) and against the vapour composition (purple, dashed curve). The green tie line joins the liquid to the vapour in equilibrium with it; the flask on the right shows both compositions as molecules. Press Play to sweep $x_{1}$.

80 kPa30 kPa0.40
$p_{1}=x_{1}p_{1}^{\circ}$—
$p_{2}=x_{2}p_{2}^{\circ}$—
total $p$—
vapour $y_{1}$—

For an ideal solution of a volatile liquid A ($p_{\mathrm{A}}^{\circ}=100\ \mathrm{kPa}$) and a less volatile liquid B ($p_{\mathrm{B}}^{\circ}=25\ \mathrm{kPa}$), which statement about liquid and vapour in equilibrium is always true?

Ideal and non-ideal solutions; azeotropes

Why should a molecule of 1 escape as easily from among molecules of 2 as from its own kind? It will do so only if the 1–2 attractions are, on average, just as strong as the 1–1 and 2–2 attractions they replace. Benzene and toluene are so alike — flat aromatic rings held together by similar dispersion forces — that this is very nearly true. Acetone and chloroform, or ethanol and water, are not alike at all.

📘 Definition 5.7 — Ideal solution

An ideal solution is one that obeys Raoult's law, $p_{i}=x_{i}p_{i}^{\circ}$, for every component over the whole range of composition (at all temperatures considered). Its molecular condition is that the attractions between unlike molecules (A–B) are the same as those between like molecules (A–A and B–B). Consequently, on forming an ideal solution from its components at constant temperature and pressure:

  • $\Delta_{\text{mix}}H=0$ — no heat is absorbed or given out;
  • $\Delta_{\text{mix}}V=0$ — the volume of the solution is the sum of the volumes of the components;
  • $\Delta_{\text{mix}}S\gt0$ and $\Delta_{\text{mix}}G\lt0$ — mixing is spontaneous, driven entirely by the increase in disorder.

Examples that are very nearly ideal: benzene + toluene, n-hexane + n-heptane, bromoethane + chloroethane, chlorobenzene + bromobenzene — pairs of molecules of similar size, shape and polarity.

📘 Definition 5.8 — Non-ideal solutions: positive and negative deviations

A non-ideal solution does not obey Raoult's law over the whole composition range. Its vapour pressure is either higher or lower than Raoult's law predicts.

  • Positive deviation: $p_{i}\gt x_{i}p_{i}^{\circ}$ and $p\gt p_{\text{Raoult}}$. The A–B attractions are weaker than the average of the A–A and B–B attractions, so molecules escape more easily from the mixture. Mixing absorbs heat and the liquid expands: $\Delta_{\text{mix}}H\gt0$, $\Delta_{\text{mix}}V\gt0$.
  • Negative deviation: $p_{i}\lt x_{i}p_{i}^{\circ}$ and $p\lt p_{\text{Raoult}}$. The A–B attractions are stronger, so molecules are held back. Mixing releases heat and the liquid contracts: $\Delta_{\text{mix}}H\lt0$, $\Delta_{\text{mix}}V\lt0$.

In both cases the deviation is largest in the middle of the composition range and vanishes at the pure liquids; each component still obeys Raoult's law when it is in large excess.

MixtureDeviationMolecular reason
ethanol + acetone; ethanol + cyclohexanepositivethe added molecules get between ethanol molecules and break some of their hydrogen bonds
acetone + carbon disulphidepositivethe strong dipole–dipole attraction between acetone molecules is replaced by weaker acetone–CS₂ attraction
ethanol + waterpositive (in vapour pressure)the mixture's vapour pressure exceeds the Raoult value; it gives a minimum-boiling azeotrope
acetone + chloroformnegativea new hydrogen bond $\mathrm{Cl_{3}C{-}H\cdots O{=}C(CH_{3})_{2}}$; the three Cl atoms make the C–H hydrogen slightly acidic
phenol + anilinenegativethe O–H of phenol hydrogen-bonds strongly to the lone pair on the N of aniline
nitric acid + water; hydrochloric acid + waternegativestrong acid–water interactions (ionisation and hydration of the ions)

Azeotropes. When the deviation is large, the total vapour pressure curve stops being monotonic: it passes through a maximum (large positive deviation) or a minimum (large negative deviation) at some intermediate composition. At that point the liquid and vapour line touch, the tie line has zero length, and the vapour has exactly the same composition as the liquid.

📘 Definition 5.9 — Azeotrope

An azeotrope (azeotropic mixture) is a liquid mixture that boils at a constant temperature and gives a vapour of the same composition as the liquid. It cannot be separated into its components by fractional distillation.

  • Minimum-boiling azeotrope — formed by solutions with a large positive deviation. Its vapour pressure is a maximum, so it boils below both pure components. Example: ethanol–water, about $95.6\%$ ethanol by mass, boiling at $351.3\ \mathrm{K}$ ($78.2\ ^{\circ}\mathrm{C}$), slightly below pure ethanol ($351.5\ \mathrm{K}$).
  • Maximum-boiling azeotrope — formed by solutions with a large negative deviation. Its vapour pressure is a minimum, so it boils above both pure components. Example: nitric acid–water, about $68\%$ $\mathrm{HNO_{3}}$ by mass, boiling near $393\ \mathrm{K}$ ($120\ ^{\circ}\mathrm{C}$); hydrochloric acid–water, about $20\%$ HCl, near $382\ \mathrm{K}$.

Distilling an azeotrope-forming mixture. On fractional distillation, the vapour moves towards the composition with the highest vapour pressure, the liquid towards the lowest. For a minimum-boiling azeotrope the distillate approaches the azeotrope and the residue becomes whichever pure component was in excess: fermented liquor gives at best $95.6\%$ ethanol (the remaining water is removed chemically, e.g. with quicklime, or with molecular sieves). For a maximum-boiling azeotrope it is the other way round: the pure component in excess distils off and the azeotrope stays behind in the flask — which is why concentrated nitric acid sold for the laboratory is about $68\%$.

✏️ Example 6 — Acetone and chloroform (JEE level)
At $35\ ^{\circ}\mathrm{C}$ the vapour pressures of pure acetone and pure chloroform are $46.0\ \mathrm{kPa}$ and $39.0\ \mathrm{kPa}$. For a mixture with equal amounts of the two, the total vapour pressure is found to be $32.0\ \mathrm{kPa}$. (a) Find the vapour pressure that Raoult's law predicts and the percentage by which the measured value differs from it. (b) Name the type of deviation and predict the signs of $\Delta_{\text{mix}}H$ and $\Delta_{\text{mix}}V$; explain at the molecular level. (c) What kind of azeotrope can this pair form? (d) A mixture richer in acetone than the azeotrope is fractionally distilled. What collects as distillate and what remains in the flask?
(a) $p_{\text{Raoult}}=0.500\times46.0+0.500\times39.0=42.5\ \mathrm{kPa}$. Measured $32.0\ \mathrm{kPa}$ is lower by $\dfrac{10.5}{42.5}\times100=24.7\%$.
(b) Negative deviation. Chloroform's C–H, made slightly acidic by three electronegative Cl atoms, forms a hydrogen bond to acetone's carbonyl oxygen. These A–B attractions are stronger than the A–A and B–B ones, so mixing releases heat ($\Delta_{\text{mix}}H\lt0$, the mixture warms) and the molecules pack more closely ($\Delta_{\text{mix}}V\lt0$).
(c) A large negative deviation gives a minimum in vapour pressure — a maximum-boiling azeotrope, boiling above both pure liquids (acetone $56\ ^{\circ}\mathrm{C}$, chloroform $61\ ^{\circ}\mathrm{C}$).
(d) The vapour is enriched in the direction of higher vapour pressure — away from the azeotrope, towards pure acetone. So pure acetone distils over, and the liquid left in the flask approaches the azeotropic composition and then boils unchanged.

In the deviation explorer set $p_{1}^{\circ}=60\ \mathrm{kPa}$, $p_{2}^{\circ}=40\ \mathrm{kPa}$ and the interaction setting $W=+1.5$ (1–2 attractions clearly weaker than 1–1 and 2–2). What will the total vapour pressure curve do?

Set $p_{1}^{\circ}=60$, $p_{2}^{\circ}=40\ \mathrm{kPa}$, $W=+1.5$: the readouts show a positive deviation, $p=72.7\ \mathrm{kPa}$ at $x_{1}=0.5$ against $50.0\ \mathrm{kPa}$ from Raoult's law, and an azeotrope (maximum vapour pressure) of $73.3\ \mathrm{kPa}$ at $x_{1}=0.64$ — a minimum-boiling azeotrope, with $\Delta_{\text{mix}}H\gt0$ and $\Delta_{\text{mix}}V\gt0$. Both partial-pressure curves bulge above their dashed Raoult lines. Now try $W=-1.5$: the curve sags to a minimum of $32.8\ \mathrm{kPa}$ at $x_{1}=0.36$ (maximum-boiling azeotrope). A small deviation such as $W=+0.3$ lifts the curve above the Raoult line but leaves no interior maximum (the highest pressure is still that of pure liquid 1) — not every non-ideal solution forms an azeotrope.
Interactive 2 — Deviation Explorer: Ideal, Positive, Negative and Azeotropes

The setting $W$ describes how the 1–2 attraction compares with the 1–1 and 2–2 attractions: $W=0$ is an ideal solution, $W\gt0$ means weaker 1–2 attraction (molecules escape more easily), $W\lt0$ stronger. The partial pressures are computed with a simple one-parameter model, $p_{1}=x_{1}p_{1}^{\circ}e^{Wx_{2}^{2}}$ and $p_{2}=x_{2}p_{2}^{\circ}e^{Wx_{1}^{2}}$ (you need not learn it — it only supplies realistic curves). Dashed lines are Raoult's law; solid curves are the "real" solution. A green dot marks an azeotrope when the total pressure has a maximum or minimum. Press Play to sweep $W$ from negative to positive.

+1.260 kPa40 kPa
deviation—
$p$ at $x_{1}=0.5$ (Raoult)—
azeotrope—
$\Delta_{\text{mix}}H$, $\Delta_{\text{mix}}V$—
⚠️ JEE Main traps

1. Liquid $x$ versus vapour $y$. Raoult's law uses mole fractions in the liquid; Dalton's law gives mole fractions in the vapour. If a question states the vapour composition, use $\dfrac1p=\sum\dfrac{y_{i}}{p_{i}^{\circ}}$ or $x_{i}=\dfrac{y_{i}p}{p_{i}^{\circ}}$ — never put $y$ into $p_{i}=x_{i}p_{i}^{\circ}$.

2. Vapour pressure is not changed by the amount of liquid or the container. Only the nature of the liquid (and, for a solution, its composition) and the temperature matter — provided liquid is still present.

3. Maximum vapour pressure means minimum boiling point. Positive deviation → maximum in $p$ → minimum-boiling azeotrope; negative deviation → minimum in $p$ → maximum-boiling azeotrope. Swapping "maximum" and "minimum" is the most common error in this topic.

4. Signs go together. Positive deviation: A–B weaker, $\Delta_{\text{mix}}H\gt0$ (cooling on mixing), $\Delta_{\text{mix}}V\gt0$. Negative deviation: A–B stronger, $\Delta_{\text{mix}}H\lt0$ (warming), $\Delta_{\text{mix}}V\lt0$. For an ideal solution both are zero but $\Delta_{\text{mix}}S\gt0$ and $\Delta_{\text{mix}}G\lt0$ — mixing is still spontaneous.

5. Mole fractions, not masses. Raoult's law needs mole fractions: "equal masses" of benzene and toluene is not $x=0.5$, because their molar masses differ.

When equal volumes of liquids X and Y are mixed, the mixture becomes noticeably warm and its volume is slightly less than the sum of the two volumes. The solution

Exercises

Treat vapours as ideal gases, with $R=8.314\ \mathrm{J\,mol^{-1}\,K^{-1}}$ and $M(\mathrm{H_{2}O})=18.0\ \mathrm{g\,mol^{-1}}$. Solutions are ideal unless the question says otherwise.

I
Vapour pressure of liquids.
  • 1 At $20\ ^{\circ}\mathrm{C}$, which has the higher vapour pressure, diethyl ether or ethanol? Explain in terms of intermolecular forces, and say which has the higher boiling point.
  • 2 Liquid water and its vapour are in equilibrium in a cylinder at $25\ ^{\circ}\mathrm{C}$. The volume is halved at constant temperature. What happens to (a) the vapour pressure, (b) the mass of vapour?
  • 3 Water boils at $70\ ^{\circ}\mathrm{C}$ at the top of a high mountain. The vapour pressure of water at $70\ ^{\circ}\mathrm{C}$ is $31.2\ \mathrm{kPa}$. What is the atmospheric pressure there?
  • 4 What mass of water vapour (in g) is present in a sealed $5.00\ \mathrm{L}$ flask at $25\ ^{\circ}\mathrm{C}$ that also contains some liquid water? ($p^{\circ}=3.17\ \mathrm{kPa}$)
  • 5 Liquid P has a vapour pressure of $40\ \mathrm{kPa}$ and liquid Q of $10\ \mathrm{kPa}$ at the same temperature. Which has the stronger intermolecular attractions, and which has the higher normal boiling point?
  • 6 The flask of part 4 is emptied and only $0.050\ \mathrm{g}$ of water is sealed in. Find the final pressure (in kPa) at $25\ ^{\circ}\mathrm{C}$.
  • 7 A solution of a non-volatile solute in water has $x_{1}=0.950$ (water). Find its vapour pressure at $25\ ^{\circ}\mathrm{C}$ in kPa.
  • 8 Why is the standard boiling point of water ($99.6\ ^{\circ}\mathrm{C}$) slightly lower than its normal boiling point ($100\ ^{\circ}\mathrm{C}$)?
1 Diethyl ether (about $59\ \mathrm{kPa}$ against $5.9\ \mathrm{kPa}$): its molecules attract only by dipole and dispersion forces, while ethanol molecules are hydrogen bonded. Ethanol therefore has the higher boiling point ($78\ ^{\circ}\mathrm{C}$ against $35\ ^{\circ}\mathrm{C}$).
2 (a) Unchanged, $3.17\ \mathrm{kPa}$ — it depends only on temperature. (b) Halved: half the vapour condenses.
3 A liquid boils when its vapour pressure equals the external pressure: $31.2\ \mathrm{kPa}$ (less than a third of sea-level pressure).
4 $n=\dfrac{3170\times0.00500}{8.314\times298.15}=6.39\times10^{-3}\ \mathrm{mol}$, i.e. $0.115\ \mathrm{g}$.
5 Q (lower vapour pressure: its molecules are held more strongly); Q also has the higher boiling point.
6 $0.050\ \mathrm{g}$ is less than the $0.115\ \mathrm{g}$ needed to saturate the flask, so it all evaporates: $p=\dfrac{nRT}{V}=\dfrac{(0.050/18.0)\times8.314\times298.15}{0.00500}=1.38\times10^{3}\ \mathrm{Pa}=1.38\ \mathrm{kPa}$, below the vapour pressure.
7 $p=x_{1}p_{1}^{\circ}=0.950\times3.17=3.01\ \mathrm{kPa}$.
8 $1\ \mathrm{bar}$ ($100\ \mathrm{kPa}$) is slightly less than $1\ \mathrm{atm}$ ($101.3\ \mathrm{kPa}$); the vapour pressure reaches the smaller value at a slightly lower temperature.
II
Raoult's law and the composition of the vapour. In parts 1–5 and 9, liquids A ($p_{\mathrm{A}}^{\circ}=60.0\ \mathrm{kPa}$) and B ($p_{\mathrm{B}}^{\circ}=20.0\ \mathrm{kPa}$) form an ideal solution.
  • 1 For $x_{\mathrm{A}}=0.30$, find both partial pressures and the total vapour pressure.
  • 2 Find the mole fraction of A in the vapour over the solution of part 1.
  • 3 Which liquid composition has a total vapour pressure of $44.0\ \mathrm{kPa}$?
  • 4 Which liquid composition is in equilibrium with a vapour containing $75\%$ A (by moles)? What is the total pressure?
  • 5 A vapour with $y_{\mathrm{A}}=0.40$ is in equilibrium with the liquid. Find the total pressure.
  • 6 At $25\ ^{\circ}\mathrm{C}$, $p^{\circ}$(benzene) $=12.8\ \mathrm{kPa}$ and $p^{\circ}$(toluene) $=3.85\ \mathrm{kPa}$. Find the total vapour pressure of a solution of $15.6\ \mathrm{g}$ benzene ($M=78.0$) and $55.2\ \mathrm{g}$ toluene ($M=92.0$).
  • 7 Find the mole fraction of benzene in the vapour over the solution of part 6.
  • 8 Show that, for an ideal solution, $\dfrac{y_{1}}{y_{2}}=\dfrac{p_{1}^{\circ}}{p_{2}^{\circ}}\cdot\dfrac{x_{1}}{x_{2}}$, and deduce that the vapour is always richer in the more volatile component.
  • 9 The vapour of part 2 is condensed and brought to equilibrium with its own vapour. Find the new total pressure and the new $y_{\mathrm{A}}$.
1 $p_{\mathrm{A}}=0.30\times60.0=18.0\ \mathrm{kPa}$; $p_{\mathrm{B}}=0.70\times20.0=14.0\ \mathrm{kPa}$; $p=32.0\ \mathrm{kPa}$.
2 $y_{\mathrm{A}}=\dfrac{18.0}{32.0}=0.5625$.
3 $20.0+40.0\,x_{\mathrm{A}}=44.0$, so $x_{\mathrm{A}}=0.60$.
4 $\dfrac{x_{\mathrm{A}}}{x_{\mathrm{B}}}=\dfrac{0.75}{0.25}\times\dfrac{20.0}{60.0}=1$: $x_{\mathrm{A}}=0.50$, and $p=30.0+10.0=40.0\ \mathrm{kPa}$.
5 $\dfrac1p=\dfrac{0.40}{60.0}+\dfrac{0.60}{20.0}=0.00667+0.0300=0.0367$; $p=27.3\ \mathrm{kPa}$ (liquid $x_{\mathrm{A}}=\tfrac{0.40\times27.3}{60.0}=0.18$).
6 Benzene $0.200\ \mathrm{mol}$, toluene $0.600\ \mathrm{mol}$: $x_{\mathrm{B}}=0.250$. $p=0.250\times12.8+0.750\times3.85=3.20+2.89=6.09\ \mathrm{kPa}$.
7 $y_{\mathrm{B}}=\dfrac{3.20}{6.09}=0.526$ — a quarter-benzene liquid gives a vapour more than half benzene.
8 $y_{1}=\dfrac{x_{1}p_{1}^{\circ}}{p}$ and $y_{2}=\dfrac{x_{2}p_{2}^{\circ}}{p}$; dividing, $p$ cancels. If $p_{1}^{\circ}\gt p_{2}^{\circ}$ the ratio $y_{1}/y_{2}$ exceeds $x_{1}/x_{2}$, so the vapour holds a larger share of component 1.
9 Liquid now $x_{\mathrm{A}}=0.5625$: $p=20.0+40.0\times0.5625=42.5\ \mathrm{kPa}$; $y_{\mathrm{A}}=\dfrac{33.75}{42.5}=0.794$.
III
Ideal and non-ideal solutions; azeotropes.
  • 1 Classify each mixture as nearly ideal, positive deviation or negative deviation: (a) n-hexane + n-heptane; (b) acetone + chloroform; (c) ethanol + water; (d) bromoethane + chloroethane; (e) nitric acid + water; (f) acetone + carbon disulphide. How many show a negative deviation?
  • 2 Two liquids with $p^{\circ}=60.0$ and $30.0\ \mathrm{kPa}$ are mixed in equal amounts (moles). The measured total vapour pressure is $50.0\ \mathrm{kPa}$. Find the Raoult value and the percentage deviation, and name the type.
  • 3 For the mixture in part 2, predict the signs of $\Delta_{\text{mix}}H$ and $\Delta_{\text{mix}}V$. Does the mixture warm up or cool down as it forms?
  • 4 $50\ \mathrm{mL}$ of acetone is mixed with $50\ \mathrm{mL}$ of chloroform. Is the volume of the mixture more than, equal to or less than $100\ \mathrm{mL}$? Why?
  • 5 Which type of deviation gives a minimum-boiling azeotrope? Explain using the vapour pressure curve.
  • 6 Why can an azeotrope not be separated by fractional distillation?
  • 7 Of the four quantities $\Delta_{\text{mix}}H$, $\Delta_{\text{mix}}V$, $\Delta_{\text{mix}}S$ and $\Delta_{\text{mix}}G$, how many are zero for an ideal solution? Give the signs of the others.
  • 8 A $50\%$ (by mass) ethanol–water mixture is fractionally distilled with a very efficient column. What is the highest mass percentage of ethanol the distillate can reach, and what remains in the flask?
  • 9 At $35\ ^{\circ}\mathrm{C}$, $p^{\circ}$(acetone) $=46.0\ \mathrm{kPa}$ and $p^{\circ}$(chloroform) $=39.0\ \mathrm{kPa}$. A mixture with $x(\text{acetone})=0.40$ has a total vapour pressure of $31.0\ \mathrm{kPa}$. By what percentage is this below the Raoult value?
1 Nearly ideal: (a), (d). Positive: (c), (f). Negative: (b), (e) — 2 mixtures.
2 Raoult: $30.0+15.0=45.0\ \mathrm{kPa}$. Measured is higher by $\dfrac{5.0}{45.0}\times100=11.1\%$: a positive deviation.
3 Positive deviation: weaker A–B attractions, so $\Delta_{\text{mix}}H\gt0$ (heat is absorbed — the mixture cools) and $\Delta_{\text{mix}}V\gt0$.
4 Less than $100\ \mathrm{mL}$: the new C–H$\cdots$O hydrogen bonds pull the molecules closer ($\Delta_{\text{mix}}V\lt0$, negative deviation).
5 A large positive deviation: the total vapour pressure passes through a maximum at some composition; that mixture reaches atmospheric pressure at the lowest temperature, so it boils below both pure liquids.
6 At the azeotropic composition the vapour has the same composition as the liquid, so evaporating and condensing produce no enrichment at all.
7 2 are zero ($\Delta_{\text{mix}}H$ and $\Delta_{\text{mix}}V$); $\Delta_{\text{mix}}S\gt0$ and $\Delta_{\text{mix}}G\lt0$.
8 The distillate approaches the minimum-boiling azeotrope, about $95.6\%$ ethanol by mass; the liquid left behind becomes water (the component in excess relative to the azeotrope).
9 Raoult: $0.40\times46.0+0.60\times39.0=18.4+23.4=41.8\ \mathrm{kPa}$. Below by $\dfrac{10.8}{41.8}\times100=25.8\%$ — a strong negative deviation.
IV
Harder problems and applications.
  • 1 An ideal solution of A and B has total vapour pressure $36.0\ \mathrm{kPa}$ at $x_{\mathrm{A}}=0.20$ and $56.0\ \mathrm{kPa}$ at $x_{\mathrm{A}}=0.70$. Find $p_{\mathrm{A}}^{\circ}$ and $p_{\mathrm{B}}^{\circ}$.
  • 2 In an ideal solution $p_{\mathrm{A}}^{\circ}=3p_{\mathrm{B}}^{\circ}$. The vapour contains $60\%$ A by moles. Find $x_{\mathrm{A}}$ in the liquid.
  • 3 Equal masses of benzene ($M=78.0$, $p^{\circ}=12.8\ \mathrm{kPa}$) and toluene ($M=92.0$, $p^{\circ}=3.85\ \mathrm{kPa}$) are mixed. Find the mole fraction of benzene in the liquid and in the vapour.
  • 4 A vapour mixture with $y_{\mathrm{A}}=0.50$ ($p_{\mathrm{A}}^{\circ}=60.0$, $p_{\mathrm{B}}^{\circ}=20.0\ \mathrm{kPa}$, ideal) is slowly compressed at constant temperature. At what pressure does the first drop of liquid appear, and what is its composition?
  • 5 Continuing part 4: at what pressure does the last bubble of vapour disappear?
  • 6 (Modelling) Model a light petrol as an ideal solution of hexane ($p^{\circ}=20.2\ \mathrm{kPa}$ at $25\ ^{\circ}\mathrm{C}$) and octane ($p^{\circ}=1.88\ \mathrm{kPa}$) with $x(\text{hexane})=0.20$. Find the mole fraction of hexane in the vapour in a fuel tank, and comment on why petrol blends are changed between winter and summer.
  • 7 Starting from Raoult's and Dalton's laws, derive $\dfrac1p=\dfrac{y_{1}}{p_{1}^{\circ}}+\dfrac{y_{2}}{p_{2}^{\circ}}$ and explain why the vapour line lies below the liquid line on a $p$–composition diagram.
1 Slope $\dfrac{56.0-36.0}{0.70-0.20}=40.0\ \mathrm{kPa}$; $p_{\mathrm{B}}^{\circ}=36.0-0.20\times40.0=28.0\ \mathrm{kPa}$; $p_{\mathrm{A}}^{\circ}=68.0\ \mathrm{kPa}$.
2 $\dfrac{x_{\mathrm{A}}}{x_{\mathrm{B}}}=\dfrac{y_{\mathrm{A}}}{y_{\mathrm{B}}}\cdot\dfrac{p_{\mathrm{B}}^{\circ}}{p_{\mathrm{A}}^{\circ}}=\dfrac{0.60}{0.40}\times\dfrac13=0.5$, so $x_{\mathrm{A}}=\tfrac13=0.333$.
3 Per gram: $\tfrac1{78.0}$ and $\tfrac1{92.0}$ mol, so $x_{\mathrm{B}}=\dfrac{92.0}{78.0+92.0}=0.541$. $p=0.541\times12.8+0.459\times3.85=6.93+1.77=8.69\ \mathrm{kPa}$; $y_{\mathrm{B}}=\dfrac{6.93}{8.69}=0.797$.
4 First drop (dew point): $\dfrac1p=\dfrac{0.50}{60.0}+\dfrac{0.50}{20.0}=0.0333$, $p=30.0\ \mathrm{kPa}$; liquid $x_{\mathrm{A}}=\dfrac{y_{\mathrm{A}}p}{p_{\mathrm{A}}^{\circ}}=\dfrac{0.50\times30.0}{60.0}=0.25$ — the first liquid is rich in the less volatile B.
5 When it is all liquid, $x_{\mathrm{A}}=0.50$ (the overall composition): $p=30.0+10.0=40.0\ \mathrm{kPa}$. Between $30$ and $40\ \mathrm{kPa}$ liquid and vapour coexist.
6 $p=0.20\times20.2+0.80\times1.88=4.04+1.50=5.54\ \mathrm{kPa}$; $y=\dfrac{4.04}{5.54}=0.729$. The vapour is $73\%$ hexane although the liquid is $20\%$ — light components escape first. In summer, refiners reduce the light fraction to cut evaporative losses and smog; in winter more is kept so that engines start in the cold.
7 $x_{i}=\dfrac{p_{i}}{p_{i}^{\circ}}=\dfrac{y_{i}p}{p_{i}^{\circ}}$; adding, $1=x_{1}+x_{2}=p\left(\dfrac{y_{1}}{p_{1}^{\circ}}+\dfrac{y_{2}}{p_{2}^{\circ}}\right)$. So at a composition $z$ the vapour line gives $p=\left(\tfrac{z}{p_{1}^{\circ}}+\tfrac{1-z}{p_{2}^{\circ}}\right)^{-1}$, a weighted harmonic mean of $p_{1}^{\circ}$ and $p_{2}^{\circ}$, while the liquid line gives the weighted arithmetic mean $zp_{1}^{\circ}+(1-z)p_{2}^{\circ}$. The harmonic mean is always the smaller (equal only at $z=0$ or $1$, or when $p_{1}^{\circ}=p_{2}^{\circ}$), so the vapour line lies below the liquid line. Example: $z=0.5$ with $p^{\circ}=60$ and $20\ \mathrm{kPa}$ gives $30\ \mathrm{kPa}$ against $40\ \mathrm{kPa}$ (parts 4 and 5).
🎯 Exam corner JEE Main · MCQJEE Main · Numerical

E1. JEE Main · MCQ Liquids A and B form an ideal solution; at the temperature of interest $p_{\mathrm{A}}^{\circ}=80\ \mathrm{kPa}$ and $p_{\mathrm{B}}^{\circ}=40\ \mathrm{kPa}$. For a solution with $x_{\mathrm{A}}=0.25$, the mole fraction of A in the vapour is (A) $0.25$ (B) $0.40$ (C) $0.60$ (D) $0.50$

Raoult $p_{\mathrm{A}}=0.25\times80=20\ \mathrm{kPa}$, $p_{\mathrm{B}}=0.75\times40=30\ \mathrm{kPa}$, $p=50\ \mathrm{kPa}$.
Dalton $y_{\mathrm{A}}=\dfrac{20}{50}=0.40$.
Answer (B).
⏱ Shortcut $\dfrac{y_{\mathrm{A}}}{y_{\mathrm{B}}}=2\times\dfrac{0.25}{0.75}=\dfrac23$, so $y_{\mathrm{A}}=\dfrac25$.

E2. JEE Main · Numerical An ideal solution of liquids A and B has a total vapour pressure of $40\ \mathrm{kPa}$ when $x_{\mathrm{A}}=0.25$ and $60\ \mathrm{kPa}$ when $x_{\mathrm{A}}=0.75$, at the same temperature. Find the vapour pressure of pure A in kPa. Give the answer to the nearest integer.

Line $p=p_{\mathrm{B}}^{\circ}+(p_{\mathrm{A}}^{\circ}-p_{\mathrm{B}}^{\circ})x_{\mathrm{A}}$; slope $=\dfrac{60-40}{0.50}=40\ \mathrm{kPa}$.
Values $p_{\mathrm{B}}^{\circ}=40-0.25\times40=30\ \mathrm{kPa}$; $p_{\mathrm{A}}^{\circ}=30+40=70\ \mathrm{kPa}$.
Answer $70$.
⏱ Shortcut Extend the straight line: from $x_{\mathrm{A}}=0.75$ to $1$ is half the step from $0.25$ to $0.75$, so add $10$: $60+10=70$.

E3. JEE Main · MCQ Which of these mixtures shows a negative deviation from Raoult's law? (A) acetone + carbon disulphide (B) ethanol + water (C) n-hexane + n-heptane (D) chloroform + acetone

Idea Negative deviation needs stronger unlike attractions. Chloroform's C–H hydrogen-bonds to acetone's C=O — a new attraction absent in either pure liquid.
Others (A) and (B) show positive deviations (weaker unlike attractions, broken dipole or hydrogen-bond networks); (C) is nearly ideal.
Answer (D).

E4. JEE Main · Numerical Liquids A ($p_{\mathrm{A}}^{\circ}=100\ \mathrm{kPa}$) and B ($p_{\mathrm{B}}^{\circ}=50\ \mathrm{kPa}$) form an ideal solution. The vapour in equilibrium with the solution contains $80\ \mathrm{mol}\%$ A. Find the total vapour pressure in kPa. Give the answer to the nearest integer.

Vapour side $\dfrac1p=\dfrac{0.80}{100}+\dfrac{0.20}{50}=0.0080+0.0040=0.0120$, so $p=83.3\ \mathrm{kPa}$.
Check Liquid: $\dfrac{x_{\mathrm{A}}}{x_{\mathrm{B}}}=\dfrac{0.80}{0.20}\times\dfrac{50}{100}=2$, $x_{\mathrm{A}}=\tfrac23$; $p=\tfrac23(100)+\tfrac13(50)=83.3\ \mathrm{kPa}$ ✓.
Answer $83$.
⏱ Shortcut When the vapour composition is given, go straight to $1/p=\sum y_{i}/p_{i}^{\circ}$ — no need to find $x$.

E5. JEE Main · MCQ For a binary liquid mixture that forms a maximum-boiling azeotrope, which statement is correct? (A) It shows a large positive deviation from Raoult's law. (B) $\Delta_{\text{mix}}H\gt0$ for the mixture. (C) At the azeotropic composition the vapour has the same composition as the liquid, and the mixture boils above both pure components. (D) Both pure components can be obtained from it by fractional distillation.

Idea Maximum boiling point ⇔ minimum vapour pressure ⇔ large negative deviation, with $\Delta_{\text{mix}}H\lt0$. So (A) and (B) are wrong.
Azeotrope At the azeotrope liquid and vapour have the same composition, so distillation cannot separate it — (D) is wrong; (C) is the definition.
Answer (C).

E6. JEE Main · Numerical The vapour above an ideal solution of A ($p_{\mathrm{A}}^{\circ}=90\ \mathrm{kPa}$) and B ($p_{\mathrm{B}}^{\circ}=45\ \mathrm{kPa}$) contains A and B in the mole ratio $1:1$. Find the total vapour pressure in kPa. Give the answer to the nearest integer.

Vapour side $\dfrac1p=\dfrac{0.5}{90}+\dfrac{0.5}{45}=\dfrac{1}{180}+\dfrac{2}{180}=\dfrac{3}{180}$, so $p=60\ \mathrm{kPa}$.
Check Equal partial pressures: $90x_{\mathrm{A}}=45(1-x_{\mathrm{A}})$, $x_{\mathrm{A}}=\tfrac13$; $p=30+30=60\ \mathrm{kPa}$ ✓.
Answer $60$.
🔬 Research–Teaching NexusResearch-tutored · optional, about 45 minutes

Research question. Does a hand sanitiser lose its alcohol faster than its water as it evaporates — and does an alcohol–water mixture evaporate faster or slower than Raoult's law would suggest?

Why it matters. Alcohol-based sanitisers must stay above about $60\%$ alcohol to kill germs; a bottle left open, or a film that dries too fast, may not. Paint, ink and fuel manufacturers tune evaporation rates by mixing solvents, and every distillation plant depends on the vapour being richer in the volatile component. Evaporation rate into still air is roughly proportional to the vapour pressure, so a kitchen balance can probe Raoult's law and its deviations.

What to do.

  1. Prepare mixtures of rubbing alcohol (or 70 % isopropyl alcohol diluted further) and water at three or four compositions, plus pure water and the alcohol as supplied. Keep everything away from flames.
  2. Pour the same mass (about $10\ \mathrm{g}$) of each into identical shallow dishes on a balance, in a draught-free room, and record the mass every five minutes for half an hour.
  3. Find the initial evaporation rate (g per minute) of each mixture and plot it against the alcohol content converted to mole fraction.
  4. Compare with a straight line joining the rates of the two pure liquids (the Raoult-like expectation). Do the mixtures lie above the line (positive deviation) or below it?
  5. Leave one mixture until half its mass has gone and test whether the remaining liquid still smells strongly of alcohol, or measure its density to estimate its composition.

Tools: Kitchen or laboratory balance (0.01–0.1 g), identical shallow dishes, timer, rubbing alcohol or ethanol-based sanitiser, a spreadsheet. No heating and no flames.

Hand in: A table and graph of evaporation rate against mole fraction of alcohol, with the straight "ideal" line drawn in; one paragraph on whether the mixture deviates positively or negatively and what that says about alcohol–water attractions; a sentence on what happens to the composition of a sanitiser film as it dries.

Going further. Rate also depends on molar mass and diffusion of the vapour. How could you correct for this, or design a test (e.g. the time for a drop to vanish on a cold surface) that depends more directly on the vapour pressure?

Instructor note: isopropyl alcohol–water and ethanol–water both show positive deviations, so intermediate mixtures usually evaporate faster than the straight-line expectation, and the alcohol fraction of a drying film falls steadily (the liquid left behind becomes watery). Results are qualitative because evaporation into air is limited by diffusion and by evaporative cooling of the dish; students should use identical dishes and compare initial rates only.

🧪 Self-check quiz

0/5 correct

Q1. The vapour pressure of a pure liquid depends on

Q2. For an ideal solution,

Q3. A solution of A and B shows a positive deviation from Raoult's law. This means that

Q4. A and B form an ideal solution with $p_{\mathrm{A}}^{\circ}=90\ \mathrm{kPa}$, $p_{\mathrm{B}}^{\circ}=30\ \mathrm{kPa}$. For $x_{\mathrm{A}}=0.5$ the mole fraction of A in the vapour is

Q5. Ethanol and water form an azeotrope containing about $95.6\%$ ethanol by mass. This azeotrope