Chapter 20 · Principles Related to Practical Chemistry

20.3 Physical Chemistry Experiments

Four bench experiments that JEE Main asks about: the enthalpy of solution of copper(II) sulphate, the enthalpy of neutralisation of a strong acid by a strong base, the preparation of lyophilic and lyophobic sols, and an iodine-clock study of the iodide–hydrogen peroxide reaction. For each: the principle, the procedure, the observation table, the calculation, the precautions and the errors.

A thermometer, a polystyrene cup, a stopwatch and a few beakers are enough equipment to measure some of the most important numbers in physical chemistry. With them you can find how much heat a mole of copper(II) sulphate gives out when it dissolves, show that every strong acid neutralises every strong base with exactly the same heat, make two very different kinds of colloid, and work out the rate law of a reaction without ever measuring a concentration while it changes. These are the physical chemistry experiments of the JEE Main practical syllabus, and the examiners like them because one experiment tests several units at once: thermochemistry and Hess's law (Section 4.1, Section 4.2), stoichiometry and the limiting reagent (Section 1.3) and rate laws (Section 8.1, Section 8.2).

A JEE question on an experiment rarely asks you to repeat the procedure. It asks why a step is done, what would change if a quantity were doubled, which reading goes into the formula, or which way an error pushes the answer. So for each experiment we set out the principle, an outline of the procedure, a model observation table, the calculation, the precautions and the main sources of error, and then solve JEE-style problems. Two virtual labs let you run the calorimeter and the iodine clock yourself. Throughout, $c=4.18\ \mathrm{J\,g^{-1}\,K^{-1}}$ for water and dilute aqueous solutions, whose density is taken as $1.00\ \mathrm{g\,mL^{-1}}$, unless a problem says otherwise.

Calorimetry and the enthalpy of solution of copper(II) sulphate

A school calorimeter is an insulated vessel — a copper can inside a wooden box packed with cotton wool, or simply two nested polystyrene cups with a lid (a "coffee-cup calorimeter") — fitted with a thermometer and a stirrer. A change is made to happen inside it at atmospheric pressure, and the heat it releases or absorbs shows up as a change of temperature of everything inside: the solution and the vessel, thermometer and stirrer. At constant pressure that heat is the enthalpy change (Section 4.1).

📘 Definition 20.8 — Heat capacity and water equivalent of a calorimeter

The heat capacity of a calorimeter $C_\text{cal}$ is the heat needed to raise the temperature of the vessel together with its stirrer and thermometer by $1\ \mathrm{K}$ (unit $\mathrm{J\,K^{-1}}$).

The water equivalent $W$ of the calorimeter is the mass of water that has the same heat capacity:

$$W=\frac{C_\text{cal}}{c_\text{water}},\qquad C_\text{cal}=W\,c_\text{water}.$$

It is quoted in grams. A calorimeter with $W=20\ \mathrm{g}$ takes up as much heat per kelvin as $20\ \mathrm{g}$ of water, so in a calculation it can be replaced by $20\ \mathrm{g}$ of extra water. A polystyrene cup has a very small $W$ (often neglected); a metal can has a larger one.

📐 Result 20.19 — The calorimetric equation

If a change taking place in $m$ grams of dilute aqueous solution, in a calorimeter of water equivalent $W$, changes the temperature by $\Delta T=T_\text{final}-T_\text{initial}$, the heat absorbed by the contents and the vessel is $(m+W)\,c\,\Delta T$. The heat of the change is equal and opposite:

$$q_{p}=-(m+W)\,c\,\Delta T,$$ $$\Delta H=\frac{q_{p}}{n}=-\frac{(m+W)\,c\,\Delta T}{n},$$

where $n$ is the amount (in mol) of the substance or of the reaction the enthalpy refers to. A temperature rise ($\Delta T\gt0$) means an exothermic change ($\Delta H\lt0$); a fall means an endothermic one. Conditions: no heat is exchanged with the surroundings during the measurement (or a correction is made for it, below), the change goes to completion, and the specific heat capacity and density of the dilute solution are taken equal to those of water.

Finding the water equivalent: the method of mixtures. Put a known mass $m_{1}$ of cold water in the calorimeter and let both come to the same temperature $T_{1}$. Add a known mass $m_{2}$ of warm water at $T_{2}$, stir and note the final steady temperature $T_{3}$. Heat lost by the warm water = heat gained by the cold water and the vessel:

$$m_{2}\,c\,(T_{2}-T_{3})=(m_{1}+W)\,c\,(T_{3}-T_{1}).$$

The specific heat capacity cancels, so $W$ comes out in grams directly. The calorimeter is then used, unchanged, for all the later experiments.

✏️ Example 1 — Calibrating a polystyrene calorimeter
A calorimeter contains $50.0\ \mathrm{g}$ of water at $20.0\ ^{\circ}\mathrm{C}$. $50.0\ \mathrm{g}$ of water at $60.0\ ^{\circ}\mathrm{C}$ is poured in and the mixture is stirred; the steady final temperature is $38.5\ ^{\circ}\mathrm{C}$. (a) Find the water equivalent and the heat capacity of the calorimeter. (b) Without a calorimeter (no heat taken by the vessel), what would the final temperature have been?
Heat balance $50.0\,c\,(60.0-38.5)=(50.0+W)\,c\,(38.5-20.0)$, i.e. $50.0\times21.5=(50.0+W)\times18.5$.
(a) $50.0+W=\dfrac{1075}{18.5}=58.1$, so $W=8.1\ \mathrm{g}$ and $C_\text{cal}=8.1\times4.18=34\ \mathrm{J\,K^{-1}}$.
(b) Equal masses of water simply average: $\dfrac{20.0+60.0}{2}=40.0\ ^{\circ}\mathrm{C}$. The vessel took $8.1\times4.18\times18.5\approx627\ \mathrm{J}$, which is why the mixture only reached $38.5\ ^{\circ}\mathrm{C}$.
Check Heat given out by the warm water, $50.0\times4.18\times21.5=4494\ \mathrm{J}$; taken by the cold water, $50.0\times4.18\times18.5=3867\ \mathrm{J}$; the difference, $627\ \mathrm{J}$, went into the vessel ✓.

The temperature–time graph and the extrapolation. No calorimeter is perfectly insulated, and a solid takes a minute or so to dissolve. While the solution is still warming up it is already losing heat to the room, so the highest reading is lower than the temperature that would have been reached if all the heat had been released instantly. The standard cure is graphical: read the thermometer every half minute for a few minutes before mixing (to fix the starting temperature) and for several minutes after. After the change is over, the temperature drifts back towards room temperature along an almost straight line. Extend that line backwards to the moment of mixing; the temperature it gives there is the one the system would have reached with no heat loss. The difference between it and the starting temperature is the corrected $\Delta T$. Interactive 1 lets you watch this correction at work.

🧭 Problem-solving strategy — Any calorimetry calculation
  1. Find $\Delta T$ with its sign — from the extrapolated graph if one is given, otherwise final minus initial (for two solutions at different temperatures, take the mean of their initial temperatures, weighted by mass if the masses differ).
  2. Find the total heat capacity: $(m+W)\,c$, where $m$ is the mass of all the liquid in the calorimeter (both solutions after mixing). Add $C_\text{cal}$ directly if it is given in $\mathrm{J\,K^{-1}}$ instead of $W$.
  3. Find $n$ — moles of the dissolved substance, or moles of water formed (the limiting reagent decides) for a neutralisation.
  4. $\Delta H=-(m+W)\,c\,\Delta T/n$, converted to $\mathrm{kJ\,mol^{-1}}$. Check the sign: warming means negative.

The experiment: enthalpy of solution of $\mathrm{CuSO_{4}}$. The enthalpy of solution (Definition 4.12, Section 4.2) is the enthalpy change when one mole of a substance dissolves in a large amount of solvent. Copper(II) sulphate is the classic choice because it exists both as the white anhydrous solid $\mathrm{CuSO_{4}}$ and as the blue pentahydrate $\mathrm{CuSO_{4}{\cdot}5H_{2}O}$, and the two behave quite differently.

Model observation table (pentahydrate, Example 2)
quantitysymbolvaluenote
mass of water$m$$100\ \mathrm{g}$$100\ \mathrm{mL}$
water equivalent$W$$10\ \mathrm{g}$method of mixtures
mass of salt$w$$6.24\ \mathrm{g}$weighed by difference
initial temperature$T_{1}$$25.00\ ^{\circ}\mathrm{C}$steady before mixing
temperature at mixing (extrapolated)$T_{2}$$24.36\ ^{\circ}\mathrm{C}$from the graph

Hess's law gives what cannot be measured. The enthalpy of hydration of the anhydrous salt to the pentahydrate, $\mathrm{CuSO_{4}(s)+5H_{2}O(l)\rightarrow CuSO_{4}{\cdot}5H_{2}O(s)}$, cannot be measured directly: the solid takes up water slowly, unevenly, and never stops neatly at exactly five molecules. But both forms dissolve quickly to the same solution, so (Law 4.8, Section 4.2)

$$\Delta_\text{sol}H(\text{anh})=\Delta_\text{hyd}H+\Delta_\text{sol}H(\text{penta}),$$ $$\Delta_\text{hyd}H=\Delta_\text{sol}H(\text{anh})-\Delta_\text{sol}H(\text{penta}),$$

where "anh" is the anhydrous salt and "penta" the pentahydrate.

Why the two forms differ. Dissolving means breaking up the lattice (costs energy) and hydrating the ions (releases energy). In the anhydrous salt the small, doubly charged $\mathrm{Cu^{2+}}$ ion has not yet met water, so the large hydration energy is released on dissolving and the solution warms. In the pentahydrate, four water molecules are already bound to each $\mathrm{Cu^{2+}}$ (and one to the sulphate) — most of the hydration has already happened in the crystal — so dissolving is dominated by breaking the lattice and is slightly endothermic.

Precautions. Powder the salt finely and add it all at once, so that it dissolves quickly; stir gently and continuously; keep the anhydrous salt in a desiccator and weigh it quickly (it absorbs moisture from the air, which releases part of its heat before the experiment and adds mass that is not $\mathrm{CuSO_{4}}$); use a thermometer reading to $0.1\ ^{\circ}\mathrm{C}$ or better; keep the lid on; use the same calorimeter whose $W$ you measured. Sources of error. Heat exchange with the surroundings (corrected by extrapolation); incomplete dissolution; partial hydration of the "anhydrous" salt (makes $\Delta_\text{sol}H$ less negative); neglecting the heat capacity of the dissolved salt and the change of specific heat of the solution; the thermometer's own lag.

✏️ Example 2 — Enthalpy of solution of the pentahydrate from a temperature–time record
$6.24\ \mathrm{g}$ of $\mathrm{CuSO_{4}{\cdot}5H_{2}O}$ ($M=249.7\ \mathrm{g\,mol^{-1}}$) is added at $t=3.0\ \mathrm{min}$ to $100\ \mathrm{g}$ of water in a calorimeter with $W=10\ \mathrm{g}$. The readings are:
$t$ / min0–3.03.54.05.06.07.08.0
$T$ / $^{\circ}\mathrm{C}$25.0024.4124.3824.4024.4224.4424.46
(a) Find the corrected temperature change. (b) Find $\Delta_\text{sol}H$ of the pentahydrate. (c) What value would a student get by using the lowest reading instead, and why is it wrong?
Find $\Delta_\text{sol}H$ (in $\mathrm{kJ\,mol^{-1}}$, with its sign) before you open the solution:
(a) After $4\ \mathrm{min}$ the solution warms steadily at $0.02\ ^{\circ}\mathrm{C}$ per minute (heat flowing in from the room). Extending this line back one minute to $t=3.0$: $24.38-0.02=24.36\ ^{\circ}\mathrm{C}$. So $\Delta T=24.36-25.00=-0.64\ \mathrm{K}$.
(b) $n=\dfrac{6.24}{249.7}=0.0250\ \mathrm{mol}$. $q_{p}=-(100+10)(4.18)(-0.64)=+294\ \mathrm{J}$ (absorbed). $\Delta_\text{sol}H=\dfrac{+294}{0.0250}=+1.18\times10^{4}\ \mathrm{J\,mol^{-1}}=+11.8\ \mathrm{kJ\,mol^{-1}}$.
(c) Lowest reading $24.38$: $\Delta T=-0.62\ \mathrm{K}$ gives $+11.4\ \mathrm{kJ\,mol^{-1}}$, about $3\%$ too small. By the time the salt had all dissolved, the room had already put some heat back into the cold solution, so the lowest reading is not as low as the true temperature drop.
Check The accepted value is $+11.7\ \mathrm{kJ\,mol^{-1}}$; the small, positive value fits the picture of an already-hydrated salt.

In the calorimeter lab choose anhydrous CuSO₄, $5.0\ \mathrm{g}$, $W=10\ \mathrm{g}$ and heat-loss rate $0.02$ per minute. Compared with the value obtained by extrapolation, the $\Delta H$ calculated from the highest thermometer reading will be

With those settings the readouts show: largest rise $+4.29\ \mathrm{K}$, extrapolated rise $+4.53\ \mathrm{K}$, so $\Delta H=-66.5\ \mathrm{kJ\,mol^{-1}}$ by extrapolation but only $-63.0\ \mathrm{kJ\,mol^{-1}}$ from the highest reading — $5.4\%$ too small in magnitude. Heat was leaking out while the salt was still dissolving, so the thermometer never reached the "no-loss" temperature. Set the heat-loss rate to $0$ and the two values agree; raise it to $0.05$ and the highest reading falls to $+4.06\ \mathrm{K}$ while the extrapolation still recovers about $+4.5\ \mathrm{K}$.
Interactive 1 — Coffee-Cup Calorimeter with Temperature–Time Graph

Choose an experiment. The calorimeter holds $100\ \mathrm{g}$ of solution in all (for the neutralisations, $50\ \mathrm{mL}$ of acid and $50\ \mathrm{mL}$ of base of the chosen concentration); the room and all solutions start at $25.00\ ^{\circ}\mathrm{C}$, and mixing happens at $t=2\ \mathrm{min}$. Press Play to take a reading every half minute. When the record is complete, the purple line is fitted to the readings from $5$ to $10\ \mathrm{min}$ and extended back to the moment of mixing. Change the water equivalent $W$ and the heat-loss rate and compare $\Delta H$ from the extrapolation with $\Delta H$ from the largest reading.

5.0 g10 g0.02 /min
ΔT (largest reading)—
ΔT (extrapolated)—
ΔH from extrapolation—
ΔH from largest reading—
✏️ Example 3 — Both forms of the salt and the hidden enthalpy of hydration
In the same calorimeter as Example 2 ($100\ \mathrm{g}$ of water, $W=10\ \mathrm{g}$), $3.99\ \mathrm{g}$ of anhydrous $\mathrm{CuSO_{4}}$ ($M=159.6\ \mathrm{g\,mol^{-1}}$) gives a corrected temperature rise of $3.62\ \mathrm{K}$. (a) Find $\Delta_\text{sol}H$ of anhydrous $\mathrm{CuSO_{4}}$. (b) Using the result of Example 2, find the enthalpy of hydration $\mathrm{CuSO_{4}(s)+5H_{2}O(l)\rightarrow CuSO_{4}{\cdot}5H_{2}O(s)}$. (c) How much heat is released when $1.00\ \mathrm{g}$ of the anhydrous salt is fully converted to the pentahydrate, and what mass of water does it take up? (d) A student's "anhydrous" sample had been left open and had already partly absorbed moisture. Would her $\Delta_\text{sol}H$ be too negative or not negative enough? What happens to her $\Delta_\text{hyd}H$?
(a) $n=\dfrac{3.99}{159.6}=0.0250\ \mathrm{mol}$; $\Delta_\text{sol}H=-\dfrac{110\times4.18\times3.62}{0.0250}=-6.66\times10^{4}\ \mathrm{J\,mol^{-1}}=-66.6\ \mathrm{kJ\,mol^{-1}}$.
(b) Hess: $\Delta_\text{hyd}H=\Delta_\text{sol}H(\text{anh})-\Delta_\text{sol}H(\text{penta})=-66.6-(+11.8)=-78.4\ \mathrm{kJ\,mol^{-1}}$.
(c) $\dfrac{1.00}{159.6}\ \mathrm{mol}\times78.4\ \mathrm{kJ\,mol^{-1}}=0.491\ \mathrm{kJ}$ released; water taken up $=\dfrac{1.00}{159.6}\times5\times18.02=0.565\ \mathrm{g}$. This is why the white powder turns blue and warm when a drop of water touches it — the familiar test for water.
(d) Part of the hydration heat has already been released before the experiment, and part of the weighed mass is water, so fewer moles of $\mathrm{CuSO_{4}}$ release less heat: $\Delta_\text{sol}H$ comes out not negative enough (smaller magnitude), and so does $\Delta_\text{hyd}H$.
⏱ Shortcut In the Hess cycle the two measured enthalpies are on the two sides of a triangle that meets at the solution: "anhydrous minus pentahydrate". If both experiments use the same amount (here $0.0250\ \mathrm{mol}$) in the same calorimeter, $\Delta_\text{hyd}H\propto-(\Delta T_\text{anh}-\Delta T_\text{penta})=-(3.62+0.64)$: $-\dfrac{459.8\times4.26}{0.0250}=-78.3\ \mathrm{kJ\,mol^{-1}}$ (the tiny difference from $-78.4$ is rounding).

The enthalpies of solution of anhydrous $\mathrm{CuSO_{4}}$ and of $\mathrm{CuSO_{4}{\cdot}5H_{2}O}$ are $-66.5$ and $+11.7\ \mathrm{kJ\,mol^{-1}}$. The enthalpy change for $\mathrm{CuSO_{4}(s)+5H_{2}O(l)\rightarrow CuSO_{4}{\cdot}5H_{2}O(s)}$ is

Enthalpy of neutralisation of a strong acid by a strong base

Mix dilute hydrochloric acid with dilute sodium hydroxide and the beaker becomes warm. Do the same with nitric acid and potassium hydroxide, or with perchloric acid and lithium hydroxide, and — per mole of water formed — the beaker warms by exactly the same amount. That surprising constancy is the point of the second experiment.

📘 Definition 20.9 — Enthalpy of neutralisation

The enthalpy of neutralisation $\Delta_\text{neut}H$ is the enthalpy change when an acid and a base react in dilute aqueous solution to form one mole of water, i.e. when one mole of $\mathrm{H^{+}(aq)}$ is neutralised by one mole of $\mathrm{OH^{-}(aq)}$. It is always quoted per mole of water formed — not per mole of acid or of base.

📐 Result 20.20 — The enthalpy of neutralisation is constant for strong acids and strong bases

For any strong acid and strong base in dilute solution,

$$\mathrm{H^{+}(aq)+OH^{-}(aq)\rightarrow H_{2}O(l)},$$ $$\Delta_\text{neut}H=-57.1\ \mathrm{kJ\,mol^{-1}}$$

(about $-13.7\ \mathrm{kcal\,mol^{-1}}$) at $298\ \mathrm{K}$. Why constant: a strong acid and a strong base are completely ionised in dilute solution, so $\mathrm{HCl(aq)+NaOH(aq)\rightarrow NaCl(aq)+H_{2}O(l)}$ is really $\mathrm{H^{+}+Cl^{-}+Na^{+}+OH^{-}\rightarrow Na^{+}+Cl^{-}+H_{2}O}$. The $\mathrm{Na^{+}}$ and $\mathrm{Cl^{-}}$ ions are spectators, and the only reaction is the same one every time. Conditions: both completely ionised, dilute solutions (so that no heat of dilution or of ion association is mixed in), same temperature.

Weak acid or weak base: the weak electrolyte must first ionise, which usually absorbs heat ($\Delta_\text{ion}H\gt0$), so

$$\Delta_\text{neut}H=\Delta_\text{ion}H+(-57.1\ \mathrm{kJ\,mol^{-1}})$$

is less negative: about $-55.9$ for $\mathrm{CH_{3}COOH}$ with NaOH, $-51.5$ for HCl with aqueous ammonia, and less still when both are weak. (HF is an exception the other way, about $-68\ \mathrm{kJ\,mol^{-1}}$, because the strongly exothermic hydration of the small $\mathrm{F^{-}}$ ion more than pays for the ionisation.)

The limiting reagent and the heat capacity. Two facts decide every JEE question on this experiment. (i) Only the limiting reagent decides the heat: $50\ \mathrm{mL}$ of $1.0\ \mathrm{M}$ HCl with $30\ \mathrm{mL}$ of $1.0\ \mathrm{M}$ NaOH forms only $0.030\ \mathrm{mol}$ of water, however much acid is left over. (ii) All the liquid in the cup shares the heat, including the excess: the leftover acid adds heat capacity but no heat, so it lowers $\Delta T$. Two consequences follow. Doubling both volumes at the same concentrations doubles the heat and doubles the mass, so $\Delta T$ is unchanged. Doubling both concentrations at the same volumes doubles the heat into the same mass, so $\Delta T$ doubles. For $V$ mL each of acid and base, both of concentration $M$ (mol/L), neglecting $W$,

$$\Delta T=\frac{57\,100\times MV/1000}{2V\times4.18}\approx6.83\,M\ \mathrm{K},$$

independent of $V$ — about $6.8\ \mathrm{K}$ for $1\ \mathrm{M}$ solutions.

Polyprotic acids. The reaction

$$\begin{aligned}&\mathrm{H_{2}SO_{4}(aq)+2NaOH(aq)}\\&\quad\rightarrow\mathrm{Na_{2}SO_{4}(aq)+2H_{2}O(l)}\end{aligned}$$

forms two moles of water per mole of acid, so the heat released per mole of sulphuric acid fully neutralised is $2\times57.1=114.2\ \mathrm{kJ}$ — but its enthalpy of neutralisation, per mole of water, is still $-57.1\ \mathrm{kJ\,mol^{-1}}$.

Precautions. Use dilute solutions (about $1\ \mathrm{M}$ or less); bring acid and base to the same temperature before mixing; mix quickly and completely, and stir; rinse the thermometer and wipe it before transferring it from the acid to the alkali (or use two thermometers checked against each other); keep the calorimeter covered. Sources of error. Heat loss to the surroundings and to the thermometer; a small temperature difference between the two solutions; absorption of $\mathrm{CO_{2}}$ by the NaOH (it then contains some carbonate and is weaker than labelled); inaccurate concentrations; neglecting the water equivalent; assuming the solution's specific heat and density equal those of water.

✏️ Example 4 — Limiting reagent, water equivalent and a weak base
(a) $100\ \mathrm{mL}$ of $0.50\ \mathrm{M}$ $\mathrm{H_{2}SO_{4}}$ and $150\ \mathrm{mL}$ of $1.0\ \mathrm{M}$ NaOH, both at $25.0\ ^{\circ}\mathrm{C}$, are mixed in a calorimeter of water equivalent $20\ \mathrm{g}$. Taking $\Delta_\text{neut}H=-57.1\ \mathrm{kJ\,mol^{-1}}$, find the final temperature. (b) In the same calorimeter, $100\ \mathrm{mL}$ of $1.0\ \mathrm{M}$ HCl is mixed with $100\ \mathrm{mL}$ of $1.0\ \mathrm{M}$ aqueous ammonia, both at the same temperature, and the corrected rise is $5.60\ \mathrm{K}$. Find the enthalpy of neutralisation of this pair and the enthalpy of ionisation of aqueous ammonia, $\mathrm{NH_{3}(aq)+H_{2}O(l)\rightarrow NH_{4}^{+}(aq)+OH^{-}(aq)}$.
Find the final temperature in (a) before you open the solution:
Moles $\mathrm{H^{+}}$: $0.100\ \mathrm{L}\times0.50\times2=0.100\ \mathrm{mol}$ (diprotic). $\mathrm{OH^{-}}$: $0.150\ \mathrm{mol}$. $\mathrm{H^{+}}$ is limiting: $0.100\ \mathrm{mol}$ of water forms; $0.050\ \mathrm{mol}$ of NaOH is left over.
(a) Heat released $=0.100\times57.1=5.71\ \mathrm{kJ}$. Heat capacity $=(100+150+20)\times4.18=1128.6\ \mathrm{J\,K^{-1}}$ — the excess alkali counts. $\Delta T=\dfrac{5710}{1128.6}=5.06\ \mathrm{K}$; final temperature $30.1\ ^{\circ}\mathrm{C}$.
(b) $n(\mathrm{H_{2}O})=0.100\ \mathrm{mol}$; heat capacity $(200+20)\times4.18=919.6\ \mathrm{J\,K^{-1}}$. $\Delta_\text{neut}H=-\dfrac{919.6\times5.60}{0.100}=-5.15\times10^{4}\ \mathrm{J\,mol^{-1}}=-51.5\ \mathrm{kJ\,mol^{-1}}$.
Ionisation $\Delta_\text{neut}H=\Delta_\text{ion}H+(-57.1)$, so $\Delta_\text{ion}H=-51.5+57.1=+5.6\ \mathrm{kJ\,mol^{-1}}$: $5.6\ \mathrm{kJ}$ of each mole's neutralisation heat is spent on ionising the weak base.
Check If the problem in (a) had said "$\Delta T$ per mole of $\mathrm{H_{2}SO_{4}}$", the heat would be $114.2\ \mathrm{kJ}$ per mole of acid — but here only $0.050\ \mathrm{mol}$ of acid reacts, $0.050\times114.2=5.71\ \mathrm{kJ}$ ✓.

Mixing $50\ \mathrm{mL}$ of $1.0\ \mathrm{M}$ HCl with $50\ \mathrm{mL}$ of $1.0\ \mathrm{M}$ NaOH raises the temperature by $\Delta T$. If $100\ \mathrm{mL}$ of each of the same solutions are mixed instead (no heat losses), the rise is

Lyophilic and lyophobic sols

Stir a little starch into boiling water and the liquid becomes faintly cloudy but never settles; drop iron(III) chloride solution into boiling water and it turns a clear, deep red-brown. Neither is a true solution, and neither is a suspension: both are colloidal sols. The JEE practical syllabus asks only how two kinds of sol are prepared and why they behave differently, so this subsection teaches just the ideas the experiment needs (surface chemistry as a whole is not in the 2026 list).

📘 Definition 20.10 — Sol, dispersed phase and dispersion medium

A colloid is a mixture in which particles of one substance, the dispersed phase, of size roughly $1\ \mathrm{nm}$ to $1000\ \mathrm{nm}$ in at least one dimension, are spread through another substance, the dispersion medium. When the dispersed phase is a solid and the medium is a liquid, the colloid is called a sol (a hydrosol if the medium is water). The particles are too small to settle or to be held back by filter paper, but large enough to scatter light: a beam of light passing through a sol is visible from the side (the Tyndall effect), whereas it is invisible in a true solution. This is the simple test that a sol has been formed.

📘 Definition 20.11 — Lyophilic and lyophobic sols

A lyophilic ("solvent-loving") sol is one in which the dispersed particles attract and hold a layer of the medium; with water as the medium it is called hydrophilic. Examples: starch, gum (gum arabic), gelatin, egg albumin in water. Such a sol forms simply by warming or stirring the substance with the medium, and if the medium is evaporated the residue can be re-dispersed simply by adding it back — the sol is reversible.

A lyophobic ("solvent-hating") sol is one in which the particles have little attraction for the medium. Examples: sols of metals (gold, silver), of metal hydroxides such as $\mathrm{Fe(OH)_{3}}$, and of metal sulphides such as $\mathrm{As_{2}S_{3}}$. They cannot be made by simply mixing; they must be made by special methods that stop the particles at colloidal size, and once coagulated they do not re-form a sol on adding the medium — they are irreversible.

propertylyophilic sol (starch, gum)lyophobic sol ($\mathrm{Fe(OH)_{3}}$, $\mathrm{As_{2}S_{3}}$)
preparationdirect: warm or stir with the mediumspecial methods: hydrolysis, double decomposition …
reversibilityreversibleirreversible
what keeps it stablemainly the layer of bound solvent (plus some charge)only the electric charge on the particles
effect of a little electrolytelittle effect; large amounts needed to precipitatecoagulated (precipitated) easily
viscosity, surface tensionhigher than the mediumabout the same as the medium
Tyndall effectweak (particles solvated, refractive index close to water)strong

Preparing the sols (procedure outline).

📐 Result 20.21 — Charge and stability of the lyophobic sols (qualitative)

A colloidal particle preferentially adsorbs, from the solution around it, ions that it has in common with its own lattice (or that are present in excess when it forms). It thereby acquires a charge, and all the particles of a sol carry the same charge, so they repel each other and do not clump together.

  • $\mathrm{Fe(OH)_{3}}$ sol made by adding $\mathrm{FeCl_{3}}$ to water adsorbs $\mathrm{Fe^{3+}}$ ions: positively charged, $\mathrm{Fe(OH)_{3}/Fe^{3+}}$.
  • $\mathrm{As_{2}S_{3}}$ sol made with $\mathrm{H_{2}S}$ adsorbs sulphide ($\mathrm{HS^{-}}$) ions: negatively charged, $\mathrm{As_{2}S_{3}/S^{2-}}$.

An added electrolyte supplies ions of the opposite charge, which neutralise the particles; they then come together and settle (coagulation). Lyophilic sols resist this because their bound solvent layer keeps the particles apart even when the charge is removed. Mixing a positive and a negative lyophobic sol neutralises both: they coagulate each other.

Precautions. Use very clean glassware and distilled water (traces of electrolyte coagulate a lyophobic sol); add $\mathrm{FeCl_{3}}$ to boiling water and only drop by drop (in cold water hydrolysis is slow; added in bulk, the excess $\mathrm{FeCl_{3}}$ and the HCl act as electrolytes and the hydroxide precipitates as a brown solid); do not overheat the starch sol or keep it for long (it is attacked by microbes); handle $\mathrm{As_{2}O_{3}}$ and $\mathrm{H_{2}S}$ only in a fume cupboard. What can go wrong. A turbid or settling product means particles grew too large — usually too much reagent added too fast, or impure water.

✏️ Example 5 — Making a ferric hydroxide sol
A student adds $10.0\ \mathrm{mL}$ of a $2.0\%$ (w/v) $\mathrm{FeCl_{3}}$ solution, drop by drop, to $100\ \mathrm{mL}$ of boiling distilled water ($M$: $\mathrm{FeCl_{3}}$ $162.2$, $\mathrm{Fe(OH)_{3}}$ $106.9\ \mathrm{g\,mol^{-1}}$). (a) Write the equation and find the greatest mass of $\mathrm{Fe(OH)_{3}}$ that can be present in the sol. (b) Assuming complete hydrolysis, find the amount of HCl formed and its concentration in the $110\ \mathrm{mL}$ of sol. Why is dialysis useful? (c) What is the sign of the charge on the particles, and why? (d) A second student pours the same $\mathrm{FeCl_{3}}$ solution all at once into cold water, and then adds a little NaCl solution "to be safe". Predict both observations.
(a) $\mathrm{FeCl_{3}(aq)+3H_{2}O(l)\rightarrow Fe(OH)_{3}(sol)+3HCl(aq)}$ (Fe 1, Cl 3, H 6, O 3 on each side). $\mathrm{FeCl_{3}}$: $\dfrac{2.0}{100}\times10.0=0.200\ \mathrm{g}$, $\dfrac{0.200}{162.2}=1.23\times10^{-3}\ \mathrm{mol}$; $\mathrm{Fe(OH)_{3}}$ at most $1.23\times10^{-3}\times106.9=0.132\ \mathrm{g}$.
(b) HCl $=3\times1.23\times10^{-3}=3.70\times10^{-3}\ \mathrm{mol}$; in $0.110\ \mathrm{L}$, $0.034\ \mathrm{mol\,L^{-1}}$. This acid is an electrolyte that slowly coagulates the sol; dialysis lets the small $\mathrm{H^{+}}$ and $\mathrm{Cl^{-}}$ ions pass out through the membrane while the colloidal particles stay inside.
(c) Positive: the freshly formed $\mathrm{Fe(OH)_{3}}$ particles adsorb $\mathrm{Fe^{3+}}$ ions (common ion, present while $\mathrm{FeCl_{3}}$ is being added), giving $\mathrm{Fe(OH)_{3}/Fe^{3+}}$.
(d) In cold water the hydrolysis is slow and incomplete: a pale yellow-brown solution of iron(III) salt, no deep red sol. Adding NaCl to a lyophobic sol supplies $\mathrm{Cl^{-}}$, which neutralises the positive particles: the sol coagulates to a brown precipitate. "Electrolyte to be safe" destroys a lyophobic sol.
🚀 Beyond JEE Main — how strongly ions coagulate, and protective colloids

Coagulation rules and protective action belong to surface chemistry, which is not in the JEE Main 2026 list; read this only for interest.

The ion that coagulates a sol is the one with charge opposite to the particles, and its power rises steeply with its charge (the Hardy–Schulze rule): for the positive $\mathrm{Fe(OH)_{3}}$ sol, $\mathrm{PO_{4}^{3-}}\gt\mathrm{SO_{4}^{2-}}\gt\mathrm{Cl^{-}}$; for the negative $\mathrm{As_{2}S_{3}}$ sol, $\mathrm{Al^{3+}}\gt\mathrm{Ba^{2+}}\gt\mathrm{Na^{+}}$. A lyophilic sol added to a lyophobic one coats its particles and protects them from coagulation; gelatin and gum arabic are such protective colloids, and the "gold number" measures how good a protector is (smaller is better).

The particles of the iron(III) hydroxide sol prepared by adding $\mathrm{FeCl_{3}}$ solution drop by drop to boiling water are

Kinetics of the reaction of iodide ions with hydrogen peroxide

In acid solution hydrogen peroxide oxidises iodide ions to iodine:

$$\begin{aligned}&\mathrm{H_{2}O_{2}(aq)+2I^{-}(aq)+2H^{+}(aq)}\\&\quad\rightarrow\mathrm{I_{2}(aq)+2H_{2}O(l)}.\end{aligned}$$

At room temperature the reaction takes minutes — slow enough to time with a stopwatch, too fast to analyse by withdrawing samples and titrating them. The trick that makes it a classroom experiment is the iodine clock: a small, fixed amount of sodium thiosulphate and some starch are added to the mixture at the start. Thiosulphate reduces iodine back to iodide almost instantly,

$$\begin{aligned}&\mathrm{I_{2}(aq)+2S_{2}O_{3}^{2-}(aq)}\\&\quad\rightarrow\mathrm{2I^{-}(aq)+S_{4}O_{6}^{2-}(aq)},\end{aligned}$$

so as long as any thiosulphate is left, no free iodine survives and the solution stays colourless. The moment the thiosulphate is used up, the next iodine formed meets the starch and the whole solution turns blue-black at once. (Each equation balances: $\mathrm{H}$ 4, $\mathrm{O}$ 2, $\mathrm{I}$ 2, net charge 0 on both sides of the first; $\mathrm{I}$ 2, $\mathrm{S}$ 4, $\mathrm{O}$ 6, charge $-4$ on both sides of the second.)

📘 Definition 20.12 — Clock reaction

A clock reaction is a reaction mixture arranged so that a sudden colour change marks the moment at which a fixed, small amount of product has formed. In the iodide–hydrogen peroxide iodine clock, the fixed amount is the iodine needed to destroy the thiosulphate added at the start: for $[\mathrm{S_{2}O_{3}^{2-}}]_{0}$ in the mixture, the blue colour appears when $\Delta[\mathrm{I_{2}}]=\tfrac12[\mathrm{S_{2}O_{3}^{2-}}]_{0}$ has been produced. The time $t$ from mixing to the colour change is the clock time.

📐 Result 20.22 — Rate from a clock time, and orders from pairs of runs

If the thiosulphate is small compared with the reactants (so that only a few per cent of the $\mathrm{H_{2}O_{2}}$ reacts before the colour appears), the rate is almost constant until then and equals the initial rate:

$$\text{rate}\approx\frac{\Delta[\mathrm{I_{2}}]}{t}=\frac{[\mathrm{S_{2}O_{3}^{2-}}]_{0}}{2t},\qquad \text{rate}\propto\frac1t$$

for runs with the same thiosulphate concentration (and the same total volume and temperature). If, between two such runs, only $[\mathrm{X}]$ changes, by a factor $f$, and the clock time changes from $t_{1}$ to $t_{2}$, the order with respect to X is

$$x=\frac{\log(t_{1}/t_{2})}{\log f}.$$

Measured this way at room temperature, in dilute acid, the reaction is first order in each reactant: $\text{rate}=k[\mathrm{H_{2}O_{2}}][\mathrm{I^{-}}]$, with $k$ of the order of $10^{-2}\ \mathrm{L\,mol^{-1}\,s^{-1}}$. The orders do not follow the coefficients: the coefficient of $\mathrm{I^{-}}$ is 2, its order 1.

Why the clock gives clean initial rates. The thiosulphate turns every iodine molecule back into two iodide ions, so $[\mathrm{I^{-}}]$ stays exactly at its starting value until the colour change. Only $\mathrm{H_{2}O_{2}}$ (and some acid, kept in excess) is used up, and only slightly. The orders fit a mechanism whose slow first step involves one $\mathrm{H_{2}O_{2}}$ and one $\mathrm{I^{-}}$ (Section 8.1):

$$\mathrm{H_{2}O_{2}+I^{-}\rightarrow H_{2}O+IO^{-}}\quad(\text{slow}),$$ $$\mathrm{IO^{-}+H^{+}\rightarrow HOI}\quad(\text{fast}),$$ $$\mathrm{HOI+I^{-}+H^{+}\rightarrow I_{2}+H_{2}O}\quad(\text{fast}).$$

The three steps add up to the overall equation, and the rate-determining step gives $\text{rate}=k[\mathrm{H_{2}O_{2}}][\mathrm{I^{-}}]$.

Model observation table (total volume $100\ \mathrm{mL}$; every run also has $10.0\ \mathrm{mL}$ of $0.010\ \mathrm{M}$ $\mathrm{Na_{2}S_{2}O_{3}}$ and $10.0\ \mathrm{mL}$ of $1.0\ \mathrm{M}$ $\mathrm{H_{2}SO_{4}}$ with starch)
run$0.20\ \mathrm{M}$ KI / mLwater / mL$0.10\ \mathrm{M}$ $\mathrm{H_{2}O_{2}}$ / mL$[\mathrm{I^{-}}]_{0}$ / M$[\mathrm{H_{2}O_{2}}]_{0}$ / M$t$ / s$1/t$ / $\mathrm{s^{-1}}$
120.040.020.00.0400.020……
240.020.020.00.0800.020……
320.020.040.00.0400.040……

In each run $[\mathrm{S_{2}O_{3}^{2-}}]_{0}=\dfrac{10.0\times0.010}{100}=1.0\times10^{-3}\ \mathrm{M}$, so the blue colour always marks $5.0\times10^{-4}\ \mathrm{M}$ of iodine formed. Precautions. Keep the temperature the same in all runs (the rate constant changes by several per cent per degree — Section 8.3); use fresh hydrogen peroxide (it decomposes on standing) and fresh starch; measure volumes with pipettes or burettes; add the reagent that starts the reaction last and all at once; keep the total volume constant. Sources of error. Judging the exact moment of the colour change; delay between mixing and starting the watch; temperature drift; air oxidation of iodide in acid (makes extra iodine, so the colour appears early); too much thiosulphate (the rate falls noticeably before the colour change, so $[\mathrm{S_{2}O_{3}^{2-}}]_{0}/2t$ underestimates the initial rate).

🧭 Problem-solving strategy — From clock times to the rate law
  1. Check that the runs you compare have the same thiosulphate, total volume and temperature. Only then is rate $\propto1/t$.
  2. Pick two runs in which only one concentration differs. Rate ratio $=t_{1}/t_{2}$ (note: the time ratio inverted). Order $=\log(\text{rate ratio})/\log(\text{concentration ratio})$.
  3. Absolute rate from one run: $[\mathrm{S_{2}O_{3}^{2-}}]_{0}/2t$; then $k=\text{rate}/([\mathrm{H_{2}O_{2}}]^{a}[\mathrm{I^{-}}]^{b})$, with units from the overall order.
  4. Predicting a clock time: scale the rate by the rate law, then $t=\dfrac{[\mathrm{S_{2}O_{3}^{2-}}]_{0}}{2\times\text{rate}}$ — and remember that more thiosulphate means proportionally more time.
✏️ Example 6 — A full iodine-clock analysis
The runs of the model table, at $25\ ^{\circ}\mathrm{C}$, gave clock times of $50\ \mathrm{s}$ (run 1), $25\ \mathrm{s}$ (run 2) and $25\ \mathrm{s}$ (run 3); in each run $[\mathrm{S_{2}O_{3}^{2-}}]_{0}=1.0\times10^{-3}\ \mathrm{M}$. (a) Find the order with respect to $\mathrm{I^{-}}$ and to $\mathrm{H_{2}O_{2}}$, and write the rate law. (b) Find the initial rate in run 1 and the rate constant with its units. (c) Predict the clock time for a run with $[\mathrm{I^{-}}]_{0}=0.060\ \mathrm{M}$, $[\mathrm{H_{2}O_{2}}]_{0}=0.030\ \mathrm{M}$ and the same thiosulphate. (d) Run 1 is repeated with twice the volume of thiosulphate solution (water reduced to keep $100\ \mathrm{mL}$). Predict the clock time and say whether the rate of reaction has changed.
Find the rate constant $k$ (in $\mathrm{L\,mol^{-1}\,s^{-1}}$) first:
(a) Runs 1→2: $[\mathrm{I^{-}}]\times2$, time $50\rightarrow25\ \mathrm{s}$, so rate $\times2$: order $\dfrac{\log2}{\log2}=1$ in $\mathrm{I^{-}}$. Runs 1→3: $[\mathrm{H_{2}O_{2}}]\times2$, rate $\times2$: order 1 in $\mathrm{H_{2}O_{2}}$. $\text{rate}=k[\mathrm{H_{2}O_{2}}][\mathrm{I^{-}}]$, overall order 2.
(b) Rate$_{1}=\dfrac{1.0\times10^{-3}}{2\times50}=1.0\times10^{-5}\ \mathrm{mol\,L^{-1}\,s^{-1}}$ (rate of formation of $\mathrm{I_{2}}$, which equals the rate of reaction). $k=\dfrac{1.0\times10^{-5}}{0.020\times0.040}=1.25\times10^{-2}\ \mathrm{L\,mol^{-1}\,s^{-1}}$.
(c) Rate $=0.0125\times0.030\times0.060=2.25\times10^{-5}\ \mathrm{mol\,L^{-1}\,s^{-1}}$; $t=\dfrac{5.0\times10^{-4}}{2.25\times10^{-5}}=22\ \mathrm{s}$.
(d) The reaction rate depends only on $[\mathrm{H_{2}O_{2}}]$ and $[\mathrm{I^{-}}]$, which are unchanged, so the rate is the same. But twice as much iodine ($1.0\times10^{-3}\ \mathrm{M}$) must now form before the colour appears: the clock time roughly doubles, to about $100\ \mathrm{s}$ (slightly more, because $\mathrm{H_{2}O_{2}}$ is depleted a little more by then).
⏱ Shortcut For (c) compare with run 1 directly: rate factor $=\tfrac{0.060}{0.040}\times\tfrac{0.030}{0.020}=2.25$, so $t=\dfrac{50}{2.25}=22\ \mathrm{s}$.

In the iodine-clock lab, start from the reference run ($[\mathrm{I^{-}}]=0.040\ \mathrm{M}$, $[\mathrm{H_{2}O_{2}}]=0.020\ \mathrm{M}$, thiosulphate $1.0\ \mathrm{mM}$). Now double the thiosulphate to $2.0\ \mathrm{mM}$ and leave everything else alone. The clock time

The reference run shows a clock time of $50.6\ \mathrm{s}$; with $2.0\ \mathrm{mM}$ thiosulphate it becomes $102.6\ \mathrm{s}$, while the "true initial rate" readout stays at $1.000\times10^{-5}\ \mathrm{M\,s^{-1}}$. Twice as much iodine has to be made before any can survive to colour the starch, so the time doubles (slightly more than doubles, because a little more peroxide is used up). Now go back to $1.0\ \mathrm{mM}$ and double $[\mathrm{I^{-}}]$ to $0.080\ \mathrm{M}$: the time falls to $25.3\ \mathrm{s}$ and $t_\text{ref}/t=2.00$ — first order in iodide. Compare clock times only between runs with the same thiosulphate.
Interactive 2 — Iodine-Clock Lab

Set the concentrations in the mixture (acid in excess, $25\ ^{\circ}\mathrm{C}$, $k=0.0125\ \mathrm{L\,mol^{-1}\,s^{-1}}$) and press Play to mix and start the stopwatch. The graph shows the iodine made by the reaction (red), the thiosulphate still left (green) and the free iodine that colours the starch (blue). The flask turns blue-black when the red curve crosses the dashed line, $\tfrac12[\mathrm{S_{2}O_{3}^{2-}}]_{0}$. The last readout compares your run with the reference run $0.040\ \mathrm{M}$ $\mathrm{I^{-}}$, $0.020\ \mathrm{M}$ $\mathrm{H_{2}O_{2}}$, $1.0\ \mathrm{mM}$ thiosulphate.

0.040 M0.020 M1.0 mM
clock time $t$—
rate from clock, $[\mathrm{S_{2}O_{3}^{2-}}]_{0}/2t$—
true initial rate $k[\mathrm{H_{2}O_{2}}][\mathrm{I^{-}}]$—
$t_\text{ref}/t$—
⚠️ JEE Main traps

1. Forgetting part of the heat capacity. The heat is shared by all the liquid (acid + base, including any excess) and the calorimeter ($W$). Using only the volume of the limiting solution, or leaving out $W$, gives the wrong $\Delta T$.

2. Per mole of what? $\Delta_\text{neut}H$ is per mole of water formed: $-57.1\ \mathrm{kJ\,mol^{-1}}$ for $\mathrm{H_{2}SO_{4}}$ + NaOH too, although one mole of $\mathrm{H_{2}SO_{4}}$ releases $114.2\ \mathrm{kJ}$. And the moles of water come from the limiting reagent.

3. Signs. A temperature rise means $\Delta H\lt0$. Anhydrous $\mathrm{CuSO_{4}}$ dissolves exothermically, the pentahydrate endothermically; $\Delta_\text{hyd}H=\Delta_\text{sol}H(\text{anh})-\Delta_\text{sol}H(\text{penta})$, not the sum.

4. Weak electrolytes give less heat. $|\Delta_\text{neut}H|$ for a weak acid or base is smaller than $57.1$ (ionisation absorbs heat); the smallest is for weak acid + weak base. HF is the well-known exception.

5. Clock time is not rate. Rate $\propto1/t$: a longer clock time means a slower reaction. Thiosulphate is not a catalyst and does not change the rate; changing its amount changes $t$ only because a different amount of iodine is being timed. And the charge on a sol depends on how it is made: $\mathrm{Fe(OH)_{3}}$ (from $\mathrm{FeCl_{3}}$ in hot water) positive, $\mathrm{As_{2}S_{3}}$ negative.

In an iodine-clock run the blue colour appears after $40\ \mathrm{s}$. The run is repeated with $[\mathrm{I^{-}}]_{0}$ halved and everything else (thiosulphate, $[\mathrm{H_{2}O_{2}}]_{0}$, total volume, temperature) unchanged. The reaction is first order in $\mathrm{I^{-}}$. The new clock time is about

Exercises

Unless a part says otherwise, take $c=4.18\ \mathrm{J\,g^{-1}\,K^{-1}}$ and density $1.00\ \mathrm{g\,mL^{-1}}$ for all aqueous solutions, $\Delta_\text{neut}H=-57.1\ \mathrm{kJ\,mol^{-1}}$ for a strong acid with a strong base, and molar masses $\mathrm{CuSO_{4}}$ $159.6$, $\mathrm{CuSO_{4}{\cdot}5H_{2}O}$ $249.7\ \mathrm{g\,mol^{-1}}$.

I
Calorimetry and the enthalpy of solution of copper(II) sulphate.
  • 1 A calorimeter has a water equivalent of $15\ \mathrm{g}$. What is its heat capacity in $\mathrm{J\,K^{-1}}$?
  • 2 $40.0\ \mathrm{g}$ of water at $25.0\ ^{\circ}\mathrm{C}$ is in a calorimeter at the same temperature. $60.0\ \mathrm{g}$ of water at $55.0\ ^{\circ}\mathrm{C}$ is added; the final temperature is $41.0\ ^{\circ}\mathrm{C}$. Find the water equivalent of the calorimeter.
  • 3 What is the total heat capacity of the calorimeter of part 2 when it holds $150\ \mathrm{mL}$ of a dilute solution?
  • 4 $4.788\ \mathrm{g}$ of anhydrous $\mathrm{CuSO_{4}}$ is dissolved in $150\ \mathrm{g}$ of water in the calorimeter of part 2 ($W=12.5\ \mathrm{g}$). The corrected temperature rise is $2.94\ \mathrm{K}$. Find $\Delta_\text{sol}H$ of anhydrous $\mathrm{CuSO_{4}}$.
  • 5 Predict the corrected temperature change when $12.485\ \mathrm{g}$ of $\mathrm{CuSO_{4}{\cdot}5H_{2}O}$ ($\Delta_\text{sol}H=+11.7\ \mathrm{kJ\,mol^{-1}}$) dissolves in $200\ \mathrm{g}$ of water in a calorimeter with $W=10\ \mathrm{g}$.
  • 6 In the experiment of part 5 the thermometer falls for about a minute and then slowly rises. Explain the rise, and explain how the temperature–time graph is used to obtain $\Delta T$.
  • 7 Given $\Delta_\text{sol}H$ of $-66.5$ (anhydrous) and $+11.7\ \mathrm{kJ\,mol^{-1}}$ (pentahydrate), find the heat released when $10.0\ \mathrm{g}$ of anhydrous $\mathrm{CuSO_{4}}$ is fully converted to the pentahydrate by liquid water.
  • 8 Explain, in terms of lattice and hydration enthalpies, why anhydrous $\mathrm{CuSO_{4}}$ dissolves exothermically but $\mathrm{CuSO_{4}{\cdot}5H_{2}O}$ endothermically.
  • 9 In part 4 a student forgets the water equivalent. Find the value of $\Delta_\text{sol}H$ she reports and her percentage error. Is her value too negative or not negative enough?
1 $C_\text{cal}=Wc=15\times4.18=62.7\ \mathrm{J\,K^{-1}}$.
2 $60.0\times(55.0-41.0)=(40.0+W)(41.0-25.0)$: $840=16(40.0+W)$, $40.0+W=52.5$, $W=12.5\ \mathrm{g}$.
3 $(150+12.5)\times4.18=679\ \mathrm{J\,K^{-1}}$.
4 $n=\dfrac{4.788}{159.6}=0.0300\ \mathrm{mol}$; $\Delta_\text{sol}H=-\dfrac{679.25\times2.94}{0.0300}=-6.66\times10^{4}\ \mathrm{J\,mol^{-1}}=-66.6\ \mathrm{kJ\,mol^{-1}}$.
5 $n=\dfrac{12.485}{249.7}=0.0500\ \mathrm{mol}$; heat absorbed $=0.0500\times11\,700=585\ \mathrm{J}$; $\Delta T=-\dfrac{585}{210\times4.18}=-0.67\ \mathrm{K}$ (a fall).
6 Once the salt has dissolved, the solution is colder than the room, so heat flows in and the temperature rises slowly and steadily. Readings are taken before and after mixing; the steady rising line after mixing is extended back to the time of mixing, and the temperature there (not the lowest reading) is used for $\Delta T$, which corrects for the heat that leaked in while the salt was dissolving.
7 $\Delta_\text{hyd}H=-66.5-11.7=-78.2\ \mathrm{kJ\,mol^{-1}}$; $\dfrac{10.0}{159.6}\times78.2=4.90\ \mathrm{kJ}$ released.
8 Dissolving = breaking up the lattice (endothermic) + hydrating the ions (exothermic). In anhydrous $\mathrm{CuSO_{4}}$ the small $\mathrm{Cu^{2+}}$ ion is not yet hydrated, so its large hydration enthalpy is released on dissolving and outweighs the lattice term. In the pentahydrate the ions (especially $\mathrm{Cu^{2+}}$, with four bound $\mathrm{H_{2}O}$) are already largely hydrated in the crystal, so little extra hydration energy is released and the lattice term wins slightly.
9 Without $W$: $-\dfrac{150\times4.18\times2.94}{0.0300}=-61.4\ \mathrm{kJ\,mol^{-1}}$. Error $=\dfrac{12.5}{162.5}\times100=7.7\%$; the value is not negative enough (too small in magnitude), because the heat taken by the vessel was left out.
II
Enthalpy of neutralisation.
  • 1 How much heat is released when $250\ \mathrm{mL}$ of $0.20\ \mathrm{M}$ $\mathrm{HNO_{3}}$ is mixed with $250\ \mathrm{mL}$ of $0.20\ \mathrm{M}$ KOH?
  • 2 Neglecting the calorimeter, find the temperature rise in part 1.
  • 3 What would the temperature rise be if (i) $500\ \mathrm{mL}$ of each of the same solutions were used, (ii) $250\ \mathrm{mL}$ each of $0.40\ \mathrm{M}$ solutions were used?
  • 4 $100\ \mathrm{mL}$ of $0.50\ \mathrm{M}$ $\mathrm{H_{2}SO_{4}}$ is mixed with $100\ \mathrm{mL}$ of $0.50\ \mathrm{M}$ NaOH. Find the moles of water formed and the temperature rise (neglect the calorimeter).
  • 5 How much heat is released when one mole of $\mathrm{H_{2}SO_{4}}$ is completely neutralised by NaOH in dilute solution? What is the enthalpy of neutralisation for this pair?
  • 6 A weak monoprotic acid HA has $\Delta_\text{neut}H=-49.8\ \mathrm{kJ\,mol^{-1}}$ with NaOH. Find its enthalpy of ionisation.
  • 7 Arrange in order of increasing magnitude of $\Delta_\text{neut}H$: HCl + NaOH; $\mathrm{CH_{3}COOH}$ + NaOH; $\mathrm{CH_{3}COOH}$ + aqueous $\mathrm{NH_{3}}$; $\mathrm{HNO_{3}}$ + KOH. Give reasons.
  • 8 Why must the solutions be dilute and at the same temperature before mixing? What would happen to the measured value if concentrated sulphuric acid were used?
  • 9 In a polystyrene cup ($W\approx0$), $50.0\ \mathrm{mL}$ of $1.0\ \mathrm{M}$ HCl and $50.0\ \mathrm{mL}$ of $1.0\ \mathrm{M}$ NaOH give a rise of $6.6\ \mathrm{K}$ (highest reading). Find the experimental $\Delta_\text{neut}H$ and its percentage deviation from $-57.1\ \mathrm{kJ\,mol^{-1}}$. Suggest two reasons for the difference.
1 $n(\mathrm{H_{2}O})=0.250\times0.20=0.050\ \mathrm{mol}$; heat $=0.050\times57.1=2.86\ \mathrm{kJ}$.
2 $\Delta T=\dfrac{2855}{500\times4.18}=1.37\ \mathrm{K}$.
3 (i) Twice the heat in twice the mass: still $1.37\ \mathrm{K}$. (ii) Twice the heat in the same mass: $2.73\ \mathrm{K}$.
4 $\mathrm{H^{+}}=0.100\ \mathrm{L}\times0.50\times2=0.100\ \mathrm{mol}$, $\mathrm{OH^{-}}=0.050\ \mathrm{mol}$ (limiting): $0.050\ \mathrm{mol}$ of water. $\Delta T=\dfrac{0.050\times57\,100}{200\times4.18}=3.42\ \mathrm{K}$.
5 Two moles of water per mole of acid: $114.2\ \mathrm{kJ}$ released ($\Delta H=-114.2\ \mathrm{kJ}$ per mole of $\mathrm{H_{2}SO_{4}}$). The enthalpy of neutralisation is still $-57.1\ \mathrm{kJ\,mol^{-1}}$ (per mole of water).
6 $\Delta_\text{ion}H=\Delta_\text{neut}H-(-57.1)=-49.8+57.1=+7.3\ \mathrm{kJ\,mol^{-1}}$.
7 $\mathrm{CH_{3}COOH}+\mathrm{NH_{3}}$ (both weak, two ionisations absorb heat) $\lt$ $\mathrm{CH_{3}COOH}$ + NaOH (one weak) $\lt$ HCl + NaOH $=$ $\mathrm{HNO_{3}}$ + KOH ($57.1$ each — the same net reaction $\mathrm{H^{+}+OH^{-}\rightarrow H_{2}O}$).
8 Dilute, so that the acid and base are fully ionised and no extra heat of dilution or of ion interaction is mixed into the measurement; same temperature, so that the starting temperature is well defined and the rise is due only to the reaction. Concentrated $\mathrm{H_{2}SO_{4}}$ releases a large heat of dilution when it mixes with water, so the measured value would be far more negative than $-57.1$.
9 $q=100\times4.18\times6.6=2759\ \mathrm{J}$; $n=0.050\ \mathrm{mol}$; $\Delta_\text{neut}H=-55.2\ \mathrm{kJ\,mol^{-1}}$, $3.4\%$ smaller in magnitude. Reasons: heat lost to the room and to the thermometer before the highest reading (no extrapolation), the heat capacity of the cup neglected, slight differences in starting temperatures or concentrations.
III
Lyophilic and lyophobic sols ($M$: $\mathrm{FeCl_{3}}$ $162.2$, $\mathrm{Fe(OH)_{3}}$ $106.9$, $\mathrm{As_{2}O_{3}}$ $197.8$, $\mathrm{As_{2}S_{3}}$ $246.0\ \mathrm{g\,mol^{-1}}$).
  • 1 Classify each as forming a lyophilic or a lyophobic sol in water: starch, gum arabic, iron(III) hydroxide, arsenious sulphide, gelatin, gold. How many are lyophilic?
  • 2 $5.0\ \mathrm{mL}$ of a $5.0\%$ (w/v) $\mathrm{FeCl_{3}}$ solution is added drop by drop to $100\ \mathrm{mL}$ of boiling water. Write the equation and find the greatest mass of $\mathrm{Fe(OH)_{3}}$ in the sol.
  • 3 $0.198\ \mathrm{g}$ of $\mathrm{As_{2}O_{3}}$ is dissolved in water and treated with excess $\mathrm{H_{2}S}$. Write the equation and find the mass of $\mathrm{As_{2}S_{3}}$ that can form.
  • 4 State and explain the sign of the charge on the particles of the sols in parts 2 and 3.
  • 5 Why is $\mathrm{FeCl_{3}}$ added to boiling water, drop by drop? What do you see if it is added quickly in large amount?
  • 6 Equal volumes of the $\mathrm{Fe(OH)_{3}}$ and $\mathrm{As_{2}S_{3}}$ sols are mixed. Predict and explain the observation.
  • 7 How would you show that the starch preparation is a sol and not a true solution? Why is starch first made into a paste with cold water?
  • 8 For the sol of part 2, find the amount of HCl formed on complete hydrolysis and its concentration in the $105\ \mathrm{mL}$ of sol.
1 Lyophilic: starch, gum arabic, gelatin (3). Lyophobic: iron(III) hydroxide, arsenious sulphide, gold.
2 $\mathrm{FeCl_{3}(aq)+3H_{2}O(l)\rightarrow Fe(OH)_{3}(sol)+3HCl(aq)}$. $\mathrm{FeCl_{3}}=0.25\ \mathrm{g}=1.54\times10^{-3}\ \mathrm{mol}$; $\mathrm{Fe(OH)_{3}}\le1.54\times10^{-3}\times106.9=0.165\ \mathrm{g}$.
3 $\mathrm{As_{2}O_{3}(aq)+3H_{2}S(aq)\rightarrow As_{2}S_{3}(sol)+3H_{2}O(l)}$. $\dfrac{0.198}{197.8}=1.00\times10^{-3}\ \mathrm{mol}$, giving $1.00\times10^{-3}\times246.0=0.246\ \mathrm{g}$ of $\mathrm{As_{2}S_{3}}$.
4 $\mathrm{Fe(OH)_{3}}$: positive — the particles adsorb $\mathrm{Fe^{3+}}$, the ion common to their lattice present in the solution. $\mathrm{As_{2}S_{3}}$: negative — they adsorb sulphide ($\mathrm{HS^{-}}$) ions from the $\mathrm{H_{2}S}$.
5 Hydrolysis of $\mathrm{Fe^{3+}}$ is fast only in hot water; adding drop by drop keeps the concentration low, so many tiny particles form instead of a few large ones, and keeps the electrolyte ($\mathrm{FeCl_{3}}$, HCl) concentration low. Added quickly in bulk, the hydroxide comes down as a brown precipitate (the excess electrolyte coagulates it).
6 The positive $\mathrm{Fe(OH)_{3}}$ particles and the negative $\mathrm{As_{2}S_{3}}$ particles neutralise each other's charge: both coagulate and settle (mutual coagulation).
7 Pass a narrow beam of light through it in a dark room: its path is visible from the side (Tyndall effect), which does not happen in a true solution such as sugar in water; it also passes through filter paper without leaving a residue. The cold paste wets each grain separately; dry starch dropped in hot water forms lumps whose outsides gelatinise and seal the dry starch inside.
8 HCl $=3\times1.54\times10^{-3}=4.62\times10^{-3}\ \mathrm{mol}$; $\dfrac{4.62\times10^{-3}}{0.105}=0.044\ \mathrm{mol\,L^{-1}}$.
IV
The iodide–hydrogen peroxide reaction by the iodine clock (all runs at the same room temperature, total volume constant, acid in excess).
  • 1 In a run, $[\mathrm{S_{2}O_{3}^{2-}}]_{0}=1.5\times10^{-3}\ \mathrm{M}$ in the mixture. What concentration of iodine has the reaction produced when the blue colour appears? Give it in units of $10^{-3}\ \mathrm{M}$.
  • 2 The blue colour in part 1 appears after $30\ \mathrm{s}$. Find the initial rate, in units of $10^{-5}\ \mathrm{mol\,L^{-1}\,s^{-1}}$.
  • 3 Doubling $[\mathrm{I^{-}}]_{0}$ changes the clock time from $60$ to $30\ \mathrm{s}$; tripling $[\mathrm{H_{2}O_{2}}]_{0}$ (with the original $[\mathrm{I^{-}}]_{0}$) changes it from $60$ to $20\ \mathrm{s}$. Find the orders and the overall order.
  • 4 For another clock reaction, doubling the concentration of a reactant changes the clock time from $80\ \mathrm{s}$ to $20\ \mathrm{s}$. What is the order with respect to that reactant?
  • 5 A run of the iodide–peroxide reaction gives $40\ \mathrm{s}$. Predict the clock time when $[\mathrm{I^{-}}]_{0}$ is made $1.5$ times and $[\mathrm{H_{2}O_{2}}]_{0}$ half as large, with the same thiosulphate.
  • 6 What happens to the clock time, and to the rate of the reaction, if (i) the thiosulphate is halved, (ii) the starch is doubled?
  • 7 Why must the total volume be the same in all runs, and why must the amount of thiosulphate be small compared with the amounts of the reactants?
  • 8 With $[\mathrm{I^{-}}]_{0}=0.10\ \mathrm{M}$, $[\mathrm{H_{2}O_{2}}]_{0}=0.010\ \mathrm{M}$ and $[\mathrm{S_{2}O_{3}^{2-}}]_{0}=1.0\times10^{-3}\ \mathrm{M}$, the clock time is $41\ \mathrm{s}$. Find $k$, assuming first order in each reactant.
  • 9 Show that the mechanism $\mathrm{H_{2}O_{2}+I^{-}\rightarrow H_{2}O+IO^{-}}$ (slow), followed by fast steps, is consistent with the measured rate law, and explain why $[\mathrm{H^{+}}]$ does not appear in it.
1 Two thiosulphate ions destroy one $\mathrm{I_{2}}$: $\tfrac12\times1.5\times10^{-3}=0.75\times10^{-3}\ \mathrm{M}$.
2 Rate $=\dfrac{0.75\times10^{-3}}{30}=2.5\times10^{-5}\ \mathrm{mol\,L^{-1}\,s^{-1}}$.
3 $[\mathrm{I^{-}}]\times2$ → rate $\times2$: order 1. $[\mathrm{H_{2}O_{2}}]\times3$ → rate $\times3$: order 1. Overall order 2.
4 Rate $\times\dfrac{80}{20}=4$ for concentration $\times2$: order $\dfrac{\log4}{\log2}=2$.
5 Rate factor $=1.5\times0.5=0.75$; $t=\dfrac{40}{0.75}=53.3\ \mathrm{s}$.
6 (i) Half as much iodine has to form: the clock time roughly halves; the rate of reaction is unchanged. (ii) Starch only shows the iodine; doubling it changes neither the time (beyond a slightly sharper colour) nor the rate.
7 Constant total volume means that changing the volume of one reagent changes only its own concentration, so one variable is changed at a time. Small thiosulphate means only a few per cent of the peroxide reacts before the colour appears, so the rate stays practically at its initial value and rate $=[\mathrm{S_{2}O_{3}^{2-}}]_{0}/2t$ is the initial rate.
8 Rate $=\dfrac{1.0\times10^{-3}}{2\times41}=1.22\times10^{-5}\ \mathrm{mol\,L^{-1}\,s^{-1}}$; $k=\dfrac{1.22\times10^{-5}}{0.10\times0.010}=1.22\times10^{-2}\ \mathrm{L\,mol^{-1}\,s^{-1}}$.
9 The overall rate is the rate of the slow step, which is elementary and bimolecular: rate $=k[\mathrm{H_{2}O_{2}}][\mathrm{I^{-}}]$ — matching the measured orders. The second $\mathrm{I^{-}}$ and both $\mathrm{H^{+}}$ enter only in the fast steps after the slow one, so they do not appear in the rate law; adding the steps ($\mathrm{IO^{-}+H^{+}\rightarrow HOI}$, $\mathrm{HOI+I^{-}+H^{+}\rightarrow I_{2}+H_{2}O}$) gives the overall equation.
🎯 Exam corner JEE Main · MCQJEE Main · Numerical

E1. JEE Main · MCQ $200\ \mathrm{mL}$ of $0.1\ \mathrm{M}$ $\mathrm{H_{2}SO_{4}}$ is mixed with $200\ \mathrm{mL}$ of $0.1\ \mathrm{M}$ NaOH. If the enthalpy of neutralisation of a strong acid by a strong base is $-57.1\ \mathrm{kJ\,mol^{-1}}$, the heat released is (A) $2.284\ \mathrm{kJ}$ (B) $1.142\ \mathrm{kJ}$ (C) $0.571\ \mathrm{kJ}$ (D) $11.42\ \mathrm{kJ}$

Moles $\mathrm{H^{+}}$: $0.200\times0.1\times2=0.040\ \mathrm{mol}$; $\mathrm{OH^{-}}$: $0.020\ \mathrm{mol}$ — limiting.
Heat $0.020\times57.1=1.142\ \mathrm{kJ}$.
Answer (B) $1.142\ \mathrm{kJ}$.
⏱ Shortcut (A) assumes all the $\mathrm{H^{+}}$ reacts; the base runs out first. Always find the limiting ion before multiplying by $57.1$.

E2. JEE Main · Numerical $100\ \mathrm{mL}$ of $1.0\ \mathrm{M}$ HCl and $100\ \mathrm{mL}$ of $1.0\ \mathrm{M}$ NaOH, both at $24.0\ ^{\circ}\mathrm{C}$, are mixed in a calorimeter of water equivalent $20\ \mathrm{g}$. The corrected final temperature is $30.2\ ^{\circ}\mathrm{C}$. Taking the specific heat of all solutions as $4.2\ \mathrm{J\,g^{-1}\,K^{-1}}$ and their density as $1\ \mathrm{g\,mL^{-1}}$, the magnitude of the enthalpy of neutralisation in $\mathrm{kJ\,mol^{-1}}$ is ____. Give the answer to the nearest integer.

Heat $q=(200+20)\times4.2\times6.2=5729\ \mathrm{J}$.
Per mole of water $n=0.100\ \mathrm{mol}$; $\dfrac{5729}{0.100}=5.73\times10^{4}\ \mathrm{J\,mol^{-1}}=57.3\ \mathrm{kJ\,mol^{-1}}$ ($\Delta_\text{neut}H=-57.3$).
Answer $57$.

E3. JEE Main · MCQ Which statement about the sols prepared in the laboratory is correct? (A) The $\mathrm{Fe(OH)_{3}}$ sol made by adding $\mathrm{FeCl_{3}}$ to boiling water is negatively charged. (B) The $\mathrm{As_{2}S_{3}}$ sol is lyophilic and is not coagulated by electrolytes. (C) A starch sol is lyophilic and can be made simply by heating starch with water. (D) Lyophobic sols are reversible: the dry residue re-forms the sol when water is added.

Check each (A) It adsorbs $\mathrm{Fe^{3+}}$: positive ✗. (B) $\mathrm{As_{2}S_{3}}$ is lyophobic (made by double decomposition) and is coagulated easily ✗. (C) Starch has a strong affinity for water; warming disperses it directly ✓. (D) That describes lyophilic sols; lyophobic sols are irreversible ✗.
Answer (C).

E4. JEE Main · Numerical In a calorimeter of total heat capacity $0.50\ \mathrm{kJ\,K^{-1}}$ (vessel plus water), $1.596\ \mathrm{g}$ of anhydrous $\mathrm{CuSO_{4}}$ raises the temperature by $1.33\ \mathrm{K}$. In the same calorimeter, $2.497\ \mathrm{g}$ of $\mathrm{CuSO_{4}{\cdot}5H_{2}O}$ lowers it by $0.234\ \mathrm{K}$. ($M$: $159.6$ and $249.7\ \mathrm{g\,mol^{-1}}$.) The magnitude of the enthalpy of hydration of $\mathrm{CuSO_{4}(s)}$ to $\mathrm{CuSO_{4}{\cdot}5H_{2}O(s)}$, in $\mathrm{kJ\,mol^{-1}}$, is ____. Give the answer to the nearest integer.

Moles Both are $0.0100\ \mathrm{mol}$.
Enthalpies of solution Anhydrous: $-\dfrac{0.50\times1.33}{0.0100}=-66.5\ \mathrm{kJ\,mol^{-1}}$. Pentahydrate: $+\dfrac{0.50\times0.234}{0.0100}=+11.7\ \mathrm{kJ\,mol^{-1}}$.
Hess $\Delta_\text{hyd}H=-66.5-11.7=-78.2\ \mathrm{kJ\,mol^{-1}}$.
Answer $78$.
⏱ Shortcut Equal moles, same calorimeter: $\dfrac{0.50\times(1.33+0.234)}{0.0100}=78.2$ in one line.

E5. JEE Main · MCQ For the iodide–hydrogen peroxide clock reaction, rate $=k[\mathrm{H_{2}O_{2}}][\mathrm{I^{-}}]$. A run gives a clock time $t$. In a new run, $[\mathrm{H_{2}O_{2}}]_{0}$, $[\mathrm{I^{-}}]_{0}$ and the thiosulphate concentration are all doubled (same total volume and temperature). The new clock time is about (A) $t/4$ (B) $t/2$ (C) $t$ (D) $2t$

Rate $2\times2=4$ times faster.
Amount timed Twice the thiosulphate: twice as much iodine must form before the blue colour.
Answer (B) $t'=\dfrac{2}{4}\,t=t/2$.
⏱ Shortcut $t\propto\dfrac{[\mathrm{S_{2}O_{3}^{2-}}]_{0}}{\text{rate}}$. (A) forgets that the thiosulphate was doubled too.

E6. JEE Main · Numerical In an iodine-clock experiment at room temperature, a mixture with $[\mathrm{I^{-}}]_{0}=0.050\ \mathrm{M}$, $[\mathrm{H_{2}O_{2}}]_{0}=0.020\ \mathrm{M}$ and $[\mathrm{S_{2}O_{3}^{2-}}]_{0}=2.0\times10^{-3}\ \mathrm{M}$ turns blue after $40\ \mathrm{s}$. The reaction is first order in each reactant. The rate constant is $x\times10^{-3}\ \mathrm{L\,mol^{-1}\,s^{-1}}$. The value of $x$ is ____. Give the answer to the nearest integer.

Rate Iodine formed $=\tfrac12\times2.0\times10^{-3}=1.0\times10^{-3}\ \mathrm{M}$ in $40\ \mathrm{s}$: rate $=2.5\times10^{-5}\ \mathrm{mol\,L^{-1}\,s^{-1}}$.
Rate constant $k=\dfrac{2.5\times10^{-5}}{0.020\times0.050}=2.5\times10^{-2}=25\times10^{-3}\ \mathrm{L\,mol^{-1}\,s^{-1}}$.
Answer $25$.
⏱ Shortcut Forgetting the factor $\tfrac12$ (two thiosulphate ions per $\mathrm{I_{2}}$) gives $50$ — the commonest slip.
🔬 Research–Teaching NexusResearch-tutored · optional, about 60 minutes in a school laboratory

Research question. Which common salt would make the best single-use "instant cold pack" for a sports first-aid kit — and how much of it is needed to cool a pack by $10\ \mathrm{K}$?

Why it matters. Instant cold packs (used by sports physiotherapists and in disaster-relief kits where there is no freezer) and self-heating food cans (used by mountaineers and armed forces around the world) both work by dissolving a salt with a large enthalpy of solution — negative for heat packs, positive for cold packs. Choosing the salt is a trade-off between the cooling per gram, cost, safety and toxicity, and every number in that trade-off comes from the coffee-cup calorimetry of this section.

What to do.

  1. Find the water equivalent of a two-cup polystyrene calorimeter by the method of mixtures.
  2. For three or four candidate salts your teacher approves (for example ammonium chloride, potassium nitrate, urea, sodium ethanoate trihydrate), dissolve about $5\ \mathrm{g}$ in $100\ \mathrm{mL}$ of water, recording the temperature every $30\ \mathrm{s}$ before and after mixing.
  3. Draw each temperature–time graph, extrapolate to the moment of mixing, and calculate $\Delta_\text{sol}H$ in $\mathrm{kJ\,mol^{-1}}$ and the heat absorbed per gram of salt.
  4. Use your best value to calculate the mass of salt needed to cool $150\ \mathrm{mL}$ of water in a pack by $10\ \mathrm{K}$. Check the prediction by making the pack.

Tools: Polystyrene cups and lids, a digital thermometer (0.1 °C), a balance, a stopwatch or phone timer, spreadsheet software for the graphs and line fits.

Hand in: The graphs with their extrapolations, a table of $\Delta_\text{sol}H$ and heat per gram for each salt, your design calculation, the measured cooling of the real pack, and a recommendation that weighs cooling against safety and cost.

Going further. Why does the cooling of a real pack fall short of your prediction? Repeat one salt at three different masses: is $\Delta_\text{sol}H$ independent of concentration, or does a heat of dilution appear?

Instructor note: ammonium chloride ($\approx+15\ \mathrm{kJ\,mol^{-1}}$) and potassium nitrate ($\approx+35\ \mathrm{kJ\,mol^{-1}}$) give clear falls of a few kelvin with $5\ \mathrm{g}$ in $100\ \mathrm{mL}$; urea is safe and cheap and is used in commercial packs. Students typically underestimate the mass needed because they forget the heat leaking in through the pack wall, which is exactly the effect the extrapolation corrects for. Avoid ammonium nitrate (an oxidiser) in school work.

🧪 Self-check quiz

0/5 correct

Q1. The water equivalent of a calorimeter is

Q2. Which pair has the least negative enthalpy of neutralisation?

Q3. An iron(III) hydroxide sol is prepared by adding iron(III) chloride solution drop by drop to boiling water. The particles are

Q4. In the iodine-clock study of the reaction between H₂O₂ and I⁻, the blue-black colour appears suddenly because

Q5. Anhydrous CuSO₄ dissolves in water with a rise in temperature, but CuSO₄·5H₂O dissolves with a small fall, mainly because