Chapter 7 · Redox Reactions and Electrochemistry

7.4 Cell Potential and Gibbs Energy, Electrolytic Cells, Batteries and Fuel Cells

The emf of a cell measures the Gibbs energy of its reaction, $\Delta G=-nFE$, which ties $E^{\circ}$, $\Delta G^{\circ}$ and $K$ into one triangle. Run a cell backwards with an external supply and you have electrolysis, where the charge passed fixes how much product forms; run it forwards in a practical package and you have the dry cell, the lead accumulator and the fuel cell.

Every morning millions of cars start because a lead–acid battery delivers a few hundred amperes for a couple of seconds; on the way to work the alternator pushes the same reaction backwards and recharges it. The aluminium of a soft-drink can was made by forcing electrons onto aluminium ions in a molten bath — about 15 kilowatt-hours of electricity for every kilogram. The chlorine that disinfects drinking water and the sodium hydroxide of soap factories come from passing a current through salt water, and the astronauts of the Apollo missions drank water produced by fuel cells that also powered their spacecraft. Electricity and chemistry trade energy in both directions, and the exchange rate is set by one equation.

In Section 7.3 we measured cell potentials and saw how they depend on concentration. Here we connect them to thermodynamics: the emf is a direct measure of the Gibbs energy change of the cell reaction, so it fixes the equilibrium constant and lets us combine half-reactions correctly. Then we drive non-spontaneous reactions with an external supply — electrolysis — and learn to predict both which products form and how much. Finally we open up three practical cells: the dry cell, the lead accumulator and the hydrogen–oxygen fuel cell. You will need the Gibbs energy ideas of Section 4.3 and the mole calculations of Section 1.3.

Cell potential and Gibbs energy

A galvanic cell pushes charge through an external circuit; the work it does on that charge is charge × potential difference. To count the charge we need the charge carried by one mole of electrons.

📘 Definition 7.16 — The Faraday constant

The Faraday constant $F$ is the magnitude of the electric charge on one mole of electrons:

$$F=N_{A}\,e=(6.022\times10^{23}\ \mathrm{mol^{-1}})(1.602\times10^{-19}\ \mathrm{C})=96\,487\ \mathrm{C\,mol^{-1}}.$$

The charge $96\,487\ \mathrm{C}$ is called one faraday. In calculations we use $F=96\,500\ \mathrm{C\,mol^{-1}}$ unless told otherwise. A reaction that transfers $n$ moles of electrons per mole of reaction moves a charge $nF$.

When a cell reaction occurs reversibly — the cell is balanced against an opposing voltage so that the current is vanishingly small — the electrical work is the maximum the reaction can deliver. From Section 4.3, the maximum non-expansion work obtainable at constant temperature and pressure is $-\Delta G$. Equating the two gives the bridge between electrochemistry and thermodynamics.

📐 Result 7.14 — Gibbs energy and cell potential

For a cell reaction that transfers $n$ moles of electrons per mole of reaction as written,

$$\Delta_{r}G=-nFE_{cell},$$ $$\Delta_{r}G^{\circ}=-nFE^{\circ}_{cell}\quad(\text{all species in standard states}).$$

Conditions: constant temperature and pressure; $E_{cell}$ is the emf measured at zero current (reversible operation); $F$ in $\mathrm{C\,mol^{-1}}$ and $E$ in volts give $\Delta G$ in $\mathrm{J\,mol^{-1}}$ ($1\ \mathrm{C\,V}=1\ \mathrm{J}$).

  • $E_{cell}\gt0\Leftrightarrow\Delta G\lt0$: spontaneous — the cell can do work (galvanic). $E_{cell}\lt0\Leftrightarrow\Delta G\gt0$: the reaction must be driven (electrolysis). $E_{cell}=0\Leftrightarrow\Delta G=0$: equilibrium.
  • $\Delta G$ is extensive: doubling the equation doubles $n$ and doubles $\Delta G$. $E$ is intensive: it stays the same.

For the Daniell cell, $\Delta_{r}G^{\circ}=-2\times96\,500\times1.10\ \mathrm{J\,mol^{-1}}$, that is $-212\ \mathrm{kJ\,mol^{-1}}$: every mole of zinc that dissolves can deliver at most $212\ \mathrm{kJ}$ of electrical work. In the direct reaction in a beaker the same Gibbs energy is simply lost.

Putting the pieces together. In Section 4.3 we met $\Delta G=\Delta G^{\circ}+RT\ln Q$ and $\Delta G^{\circ}=-RT\ln K$. Divide the first by $-nF$ and the Nernst equation of Section 7.3 appears, $E=E^{\circ}-\dfrac{RT}{nF}\ln Q$; combine the second with Result 7.14 and we have three ways of saying the same thing.

📐 Result 7.15 — The $\Delta G^{\circ}$, $K$, $E^{\circ}$ triangle
$$\Delta G^{\circ}=-nFE^{\circ}_{cell}=-RT\ln K,$$ $$E^{\circ}_{cell}=\frac{RT}{nF}\ln K=\frac{0.059}{n}\log K\quad(298\ \mathrm{K}).$$
$\Delta G^{\circ}$$E^{\circ}_{cell}$$K$at equilibrium
negativepositive$\gt1$products favoured
00$1$neither favoured
positivenegative$\lt1$reactants favoured

Any one of the three quantities gives the other two. At $298\ \mathrm{K}$, $RT\ln10=5.71\ \mathrm{kJ\,mol^{-1}}$: every factor of 10 in $K$ is worth $5.71\ \mathrm{kJ\,mol^{-1}}$ of $\Delta G^{\circ}$, or $0.059/n$ volts of $E^{\circ}$.

Temperature dependence. Since $\Delta G^{\circ}=\Delta H^{\circ}-T\Delta S^{\circ}$ and $\Delta G^{\circ}=-nFE^{\circ}$, measuring $E^{\circ}$ at two temperatures gives the entropy and enthalpy of the cell reaction: $\Delta S^{\circ}=nF\,\dfrac{dE^{\circ}}{dT}$ and $\Delta H^{\circ}=-nFE^{\circ}+T\Delta S^{\circ}$. An electrical measurement replaces a calorimeter.

Combining half-reactions. A cell potential is a difference of two electrode potentials, and in a complete cell reaction the electrons cancel, so $E^{\circ}_{cell}=E^{\circ}_{\text{cathode}}-E^{\circ}_{\text{anode}}$ works whatever the coefficients. But adding two half-reactions to make a third half-reaction is different: electrons are left over, and the potentials do not simply add. Gibbs energies always add.

📐 Rule 7.16 — Combining half-reactions

If half-reaction 3 is the sum of half-reactions 1 and 2 (with $n_{3}=n_{1}+n_{2}$ electrons), add their Gibbs energies $\Delta G^{\circ}=-nFE^{\circ}$:

$$-n_{3}FE^{\circ}_{3}=-n_{1}FE^{\circ}_{1}-n_{2}FE^{\circ}_{2},$$ $$E^{\circ}_{3}=\frac{n_{1}E^{\circ}_{1}+n_{2}E^{\circ}_{2}}{n_{3}}.$$

(If a half-reaction is reversed, its $\Delta G^{\circ}$ — and in this formula its $n_{i}E^{\circ}_{i}$ — changes sign.) The potentials are averaged, weighted by electrons; they are never simply added.

✏️ Example 1 — Gibbs energy and work from the Daniell cell
For the Daniell cell, $E^{\circ}_{cell}=1.10\ \mathrm{V}$ at $298\ \mathrm{K}$. (a) Find $\Delta_{r}G^{\circ}$. (b) What is the maximum electrical work obtainable when $6.54\ \mathrm{g}$ of zinc dissolves under standard conditions ($\mathrm{Zn}=65.4$)? (c) Find $\log K$. (d) At some stage the emf has fallen to $1.07\ \mathrm{V}$. Find $\Delta_{r}G$ of the cell reaction at that moment. Take $F=96\,500\ \mathrm{C\,mol^{-1}}$.
(a) $\mathrm{Zn+Cu^{2+}\rightarrow Zn^{2+}+Cu}$, $n=2$: $\Delta_{r}G^{\circ}=-2\times96\,500\times1.10=-212\,300\ \mathrm{J\,mol^{-1}}=-212.3\ \mathrm{kJ\,mol^{-1}}$.
(b) $6.54\ \mathrm{g}$ is $0.100\ \mathrm{mol}$ of Zn, i.e. $0.100\ \mathrm{mol}$ of reaction: $w_{\max}=0.100\times212.3=21.2\ \mathrm{kJ}$.
(c) $\log K=\dfrac{2\times1.10}{0.059}=37.3$ (equivalently $\ln K=\dfrac{212\,300}{8.314\times298}=85.7$).
(d) $\Delta_{r}G=-2\times96\,500\times1.07=-206.5\ \mathrm{kJ\,mol^{-1}}$ — still strongly negative, because $Q$ is still far below $K$.
Check $\Delta G^{\circ}=-RT\ln K=-(8.314)(298)(85.7)=-212\ \mathrm{kJ\,mol^{-1}}$ ✓ — the three corners of the triangle agree.
✏️ Example 2 — Potentials that do not add, and a disproportionation (JEE level)
(a) Given $E^{\circ}_{\mathrm{Fe^{3+}/Fe^{2+}}}=+0.77\ \mathrm{V}$ and $E^{\circ}_{\mathrm{Fe^{2+}/Fe}}=-0.44\ \mathrm{V}$, find $E^{\circ}_{\mathrm{Fe^{3+}/Fe}}$. (b) Given $E^{\circ}_{\mathrm{Cu^{2+}/Cu}}=+0.34\ \mathrm{V}$ and $E^{\circ}_{\mathrm{Cu^{2+}/Cu^{+}}}=+0.15\ \mathrm{V}$, find $E^{\circ}_{\mathrm{Cu^{+}/Cu}}$. (c) Is $\mathrm{Cu^{+}}$ stable in water, or does it disproportionate into $\mathrm{Cu^{2+}}$ and $\mathrm{Cu}$? Find $K$ for $\mathrm{2Cu^{+}(aq)\rightleftharpoons Cu^{2+}(aq)+Cu(s)}$ at $298\ \mathrm{K}$.
Find $E^{\circ}_{\mathrm{Cu^{+}/Cu}}$ in (b) before you open the solution:
(a) $\mathrm{Fe^{3+}+e^{-}\rightarrow Fe^{2+}}$ ($n=1$) plus $\mathrm{Fe^{2+}+2e^{-}\rightarrow Fe}$ ($n=2$) gives $\mathrm{Fe^{3+}+3e^{-}\rightarrow Fe}$ ($n=3$): $E^{\circ}=\dfrac{1(0.77)+2(-0.44)}{3}=\dfrac{-0.11}{3}=-0.037\ \mathrm{V}$. (Simply adding would give $+0.33\ \mathrm{V}$ — wrong even in sign.)
(b) $\mathrm{Cu^{2+}+2e^{-}\rightarrow Cu}$ = $(\mathrm{Cu^{2+}+e^{-}\rightarrow Cu^{+}})+(\mathrm{Cu^{+}+e^{-}\rightarrow Cu})$: $2(0.34)=1(0.15)+1\cdot E^{\circ}$, so $E^{\circ}_{\mathrm{Cu^{+}/Cu}}=0.68-0.15=+0.53\ \mathrm{V}$.
(c) Feasibility In $\mathrm{2Cu^{+}\rightarrow Cu^{2+}+Cu}$, one $\mathrm{Cu^{+}}$ is reduced (cathode couple $\mathrm{Cu^{+}/Cu}$, $0.53$) and one oxidised (anode couple $\mathrm{Cu^{2+}/Cu^{+}}$, $0.15$): $E^{\circ}=0.53-0.15=+0.38\ \mathrm{V}$, $n=1$. Positive, so $\mathrm{Cu^{+}}$ disproportionates.
(c) K $\log K=\dfrac{1\times0.38}{0.059}=6.44$, $K=2.8\times10^{6}$; $\Delta G^{\circ}=-96\,500\times0.38=-36.7\ \mathrm{kJ\,mol^{-1}}$. This is why copper(I) exists in water only in insoluble compounds ($\mathrm{CuI}$, $\mathrm{Cu_{2}O}$) or complexes.
Rule A species disproportionates when the potential of the couple below it ($\mathrm{Cu^{+}/Cu}$) is higher than that of the couple above it ($\mathrm{Cu^{2+}/Cu^{+}}$).

The equation of a cell reaction is multiplied throughout by 2. Which statement is correct?

Electrolytic cells and the products of electrolysis

Connect a Daniell cell to a power supply of more than $1.10\ \mathrm{V}$, positive terminal to the copper and negative to the zinc, and the current reverses: copper dissolves and zinc is plated out. The supply is now forcing the non-spontaneous reaction $\mathrm{Cu+Zn^{2+}\rightarrow Cu^{2+}+Zn}$ ($\Delta G^{\circ}=+212\ \mathrm{kJ\,mol^{-1}}$). This is electrolysis.

📘 Definition 7.17 — Electrolytic cell; electrolysis

An electrolytic cell uses electrical energy from an external source to drive a non-spontaneous redox reaction; the process is electrolysis. The electrolyte is a melt or a solution of ions between two electrodes.

  • The anode is still where oxidation occurs, but it is connected to the positive terminal of the supply; anions drift towards it.
  • The cathode is still where reduction occurs, connected to the negative terminal; cations drift towards it.
  • The applied voltage must exceed the emf of the reverse (spontaneous) cell — for $1\ \mathrm{M}$ solutions $-E^{\circ}_{cell}$ — plus the extra voltage needed to drive the electrode reactions at a useful rate and to push the current through the electrolyte.
galvanic cellelectrolytic cell
energy changechemical → electrical; $\Delta G\lt0$electrical → chemical; $\Delta G\gt0$
anode (oxidation)negativepositive
cathode (reduction)positivenegative
electrons enter the wire atthe anode (pushed by the reaction)the anode (pulled by the supply)
salt bridgeusually two compartmentsusually one vessel

How much product? In 1833 Michael Faraday found that the amount of substance produced at an electrode depends only on the quantity of electricity passed. In the language of moles this is simply stoichiometry with electrons as a reactant: a current $I$ flowing for a time $t$ delivers a charge $Q=It$, which is $Q/F$ moles of electrons.

📐 Result 7.17 — Charge and the amount of product in electrolysis

For an electrode reaction that uses $z$ electrons per formula unit of product, e.g. $\mathrm{M^{z+}+ze^{-}\rightarrow M}$, a steady current $I$ (in A) for a time $t$ (in s) gives

$$Q=It,\qquad n(\mathrm{e^{-}})=\frac{Q}{F},$$ $$n(\text{product})=\frac{It}{zF},\qquad m=\frac{M\,It}{zF}.$$
  • Cells in series carry the same charge, so the amounts of products are in the ratio $\tfrac1{z}$ and their masses in the ratio of $\tfrac{M}{z}$: $\dfrac{m_{1}}{m_{2}}=\dfrac{M_{1}/z_{1}}{M_{2}/z_{2}}$. ($M/z$ is often called the equivalent mass.)
  • For a gas, $n=\dfrac{It}{zF}$ moles occupy $22.4\ \mathrm{L\,mol^{-1}}$ at STP ($273\ \mathrm{K}$, $1\ \mathrm{atm}$); for example $z=2$ for $\mathrm{H_{2}}$ and $\mathrm{Cl_{2}}$, $z=4$ for $\mathrm{O_{2}}$.
  • If part of the current is wasted on side reactions, the current efficiency is (actual amount ÷ amount predicted from $It$) × 100%.
✏️ Example 3 — Electrolysing copper sulphate with platinum electrodes
A current of $1.50\ \mathrm{A}$ is passed for $30.0\ \mathrm{min}$ through $250\ \mathrm{mL}$ of copper sulphate solution between platinum electrodes. Copper is deposited at the cathode and oxygen is evolved at the anode. Find (a) the mass of copper deposited, (b) the volume of oxygen at STP, and (c) the pH of the solution afterwards, assuming the volume is unchanged and the solution was neutral at the start ($\mathrm{Cu}=63.5$, $F=96\,500\ \mathrm{C\,mol^{-1}}$).
Find the mass of copper (a) first:
Charge $Q=1.50\times1800=2700\ \mathrm{C}$; $n(\mathrm{e^{-}})=\dfrac{2700}{96\,500}=0.02798\ \mathrm{mol}$.
(a) Cathode $\mathrm{Cu^{2+}(aq)+2e^{-}\rightarrow Cu(s)}$: $n(\mathrm{Cu})=0.01399\ \mathrm{mol}$, $m=0.01399\times63.5=0.888\ \mathrm{g}$.
(b) Anode $\mathrm{2H_{2}O(l)\rightarrow O_{2}(g)+4H^{+}(aq)+4e^{-}}$: $n(\mathrm{O_{2}})=\dfrac{0.02798}{4}=0.006995\ \mathrm{mol}$, $V=0.006995\times22.4=0.157\ \mathrm{L}=157\ \mathrm{mL}$.
(c) One $\mathrm{H^{+}}$ is formed for every electron: $0.02798\ \mathrm{mol}$ in $0.250\ \mathrm{L}$ gives $[\mathrm{H^{+}}]=0.112\ \mathrm{M}$, $\mathrm{pH}=0.95$. The solution has turned into dilute sulphuric acid: overall $\mathrm{2CuSO_{4}+2H_{2}O\rightarrow 2Cu+O_{2}+2H_{2}SO_{4}}$.
Check Mass ratio $\mathrm{Cu}:\mathrm{O_{2}}=0.888:0.224$ equals $\dfrac{63.5}{2}:\dfrac{32.0}{4}=31.75:8.00$ ✓ (same charge, masses in the ratio $M/z$).

Which products? In a molten salt there is only one cation and one anion, so the products are fixed: molten $\mathrm{NaCl}$ gives sodium at the cathode and chlorine at the anode. In aqueous solution water competes at both electrodes:

$$\text{cathode:}\quad \mathrm{2H_{2}O(l)+2e^{-}\rightarrow H_{2}(g)+2OH^{-}(aq)},\quad E^{\circ}=-0.83\ \mathrm{V}$$ $$\text{anode:}\quad \mathrm{2H_{2}O(l)\rightarrow O_{2}(g)+4H^{+}(aq)+4e^{-}},\quad E^{\circ}_{\text{red}}=+1.23\ \mathrm{V}$$

The general rule is that the reaction needing the least energy wins: at the cathode the species that is most easily reduced (highest reduction potential), at the anode the species that is most easily oxidised (lowest reduction potential of its couple). But electrode reactions that involve gases are often slow, and need an extra push.

📘 Definition 7.18 — Overpotential

The overpotential of an electrode reaction is the extra voltage, beyond the value predicted by the Nernst equation, that must be applied to make the reaction go at an appreciable rate. It is a kinetic effect: it depends on the electrode material, the current density and the temperature. It is large for the evolution of $\mathrm{O_{2}}$ (several tenths of a volt on most anodes) and for $\mathrm{H_{2}}$ on metals such as mercury, zinc and lead; it is small for $\mathrm{H_{2}}$ on platinum black and for the deposition of metals.

📐 Rule 7.18 — Predicting the products of electrolysis of aqueous solutions

At the cathode (reduction):

  • Ions of very reactive metals — $\mathrm{Li^{+}}$, $\mathrm{K^{+}}$, $\mathrm{Na^{+}}$, $\mathrm{Ca^{2+}}$, $\mathrm{Mg^{2+}}$, $\mathrm{Al^{3+}}$ — are never reduced from water: $\mathrm{H_{2}}$ is evolved instead (and the solution near the cathode becomes alkaline). These metals are made by electrolysing melts.
  • Ions of metals with positive $E^{\circ}$ — $\mathrm{Cu^{2+}}$, $\mathrm{Ag^{+}}$, $\mathrm{Au^{3+}}$ — are reduced and the metal is deposited.
  • From acids, $\mathrm{H^{+}}$ is reduced to $\mathrm{H_{2}}$. (Moderately reactive metals such as Zn and Ni can be deposited from concentrated solutions because hydrogen has a high overpotential on them — the basis of electroplating.)

At an inert anode (Pt, graphite) (oxidation):

  • $\mathrm{I^{-}}$ and $\mathrm{Br^{-}}$ are oxidised to the halogen. $\mathrm{Cl^{-}}$ is oxidised to $\mathrm{Cl_{2}}$ from concentrated solutions — although $E^{\circ}_{\mathrm{Cl_{2}/Cl^{-}}}=1.36\ \mathrm{V}$ is higher than $1.23\ \mathrm{V}$, the overpotential of oxygen makes chloride win; from very dilute chloride solutions oxygen is the main product.
  • Oxoanions ($\mathrm{SO_{4}^{2-}}$, $\mathrm{NO_{3}^{-}}$, $\mathrm{CO_{3}^{2-}}$) and $\mathrm{F^{-}}$ are not oxidised: water gives $\mathrm{O_{2}}$ and the solution near the anode becomes acidic. (At high current density, concentrated sulphuric acid is oxidised to peroxodisulphate, $\mathrm{S_{2}O_{8}^{2-}}$.) In alkaline solution, $\mathrm{4OH^{-}\rightarrow O_{2}+2H_{2}O+4e^{-}}$.

At an active anode (a metal such as Cu, Ag or Ni dipping into a solution of its own ions) the anode itself is oxidised and dissolves — the basis of electrorefining and electroplating.

electrolyte (electrodes)cathode productanode productleft in solution
molten $\mathrm{NaCl}$ (graphite / iron)$\mathrm{Na(l)}$$\mathrm{Cl_{2}(g)}$—
concentrated $\mathrm{NaCl(aq)}$ (inert)$\mathrm{H_{2}(g)}$$\mathrm{Cl_{2}(g)}$$\mathrm{NaOH}$
$\mathrm{CuSO_{4}(aq)}$ (Pt)$\mathrm{Cu(s)}$$\mathrm{O_{2}(g)}$$\mathrm{H_{2}SO_{4}}$
$\mathrm{CuSO_{4}(aq)}$ (Cu)$\mathrm{Cu(s)}$Cu dissolves$\mathrm{CuSO_{4}}$ unchanged
$\mathrm{AgNO_{3}(aq)}$ (Pt)$\mathrm{Ag(s)}$$\mathrm{O_{2}(g)}$$\mathrm{HNO_{3}}$
dilute $\mathrm{H_{2}SO_{4}}$ or $\mathrm{Na_{2}SO_{4}(aq)}$ (Pt)$\mathrm{H_{2}(g)}$$\mathrm{O_{2}(g)}$water electrolysed; solute unchanged
✏️ Example 4 — The chlor-alkali cell (JEE level)
$2.0\ \mathrm{L}$ of concentrated brine is electrolysed between inert electrodes with a current of $5.0\ \mathrm{A}$ for $1.0\ \mathrm{h}$, the gases being kept apart. (a) Write the electrode reactions and the overall reaction. (b) Find the volumes of the gases at STP. (c) Find the pH of the solution at the end, assuming $100\%$ current efficiency and unchanged volume ($F=96\,500\ \mathrm{C\,mol^{-1}}$, $298\ \mathrm{K}$).
(a) Cathode: $\mathrm{2H_{2}O(l)+2e^{-}\rightarrow H_{2}(g)+2OH^{-}(aq)}$ ($\mathrm{Na^{+}}$ is not reduced). Anode: $\mathrm{2Cl^{-}(aq)\rightarrow Cl_{2}(g)+2e^{-}}$ (concentrated chloride beats oxygen). Overall: $\mathrm{2NaCl(aq)+2H_{2}O(l)\rightarrow 2NaOH(aq)+H_{2}(g)+Cl_{2}(g)}$.
Charge $Q=5.0\times3600=18\,000\ \mathrm{C}$; $n(\mathrm{e^{-}})=0.1865\ \mathrm{mol}$.
(b) $n(\mathrm{H_{2}})=n(\mathrm{Cl_{2}})=\dfrac{0.1865}{2}=0.0933\ \mathrm{mol}$; each occupies $0.0933\times22.4=2.09\ \mathrm{L}$ at STP.
(c) $n(\mathrm{OH^{-}})=n(\mathrm{e^{-}})=0.1865\ \mathrm{mol}$ in $2.0\ \mathrm{L}$: $[\mathrm{OH^{-}}]=0.0933\ \mathrm{M}$, $\mathrm{pOH}=1.03$, $\mathrm{pH}=12.97$.
Note If the chlorine were allowed to mix with the alkali it would react ($\mathrm{Cl_{2}+2OH^{-}\rightarrow Cl^{-}+OCl^{-}+H_{2}O}$) — that is how bleach is made. Industrial cells keep the products apart with a membrane that lets only $\mathrm{Na^{+}}$ through.

In the electrolysis lab choose CuSO₄(aq) with copper electrodes, $I=2.0\ \mathrm{A}$ and $t=60\ \mathrm{min}$. What happens?

With these settings the readouts show $Q=7200\ \mathrm{C}$, $n(\mathrm{e^{-}})=0.0746\ \mathrm{mol}$, cathode: Cu deposited $2.37\ \mathrm{g}$, anode: Cu dissolved $2.37\ \mathrm{g}$. The copper anode is oxidised more easily ($E^{\circ}=+0.34\ \mathrm{V}$) than water ($+1.23\ \mathrm{V}$ plus overpotential), so it dissolves instead of oxygen being formed; the $\mathrm{Cu^{2+}}$ concentration stays constant. Switch to CuSO₄(aq) with Pt electrodes: the cathode gain is the same $2.37\ \mathrm{g}$, but the anode now gives $418\ \mathrm{mL}$ of oxygen and the solution fades and turns acidic. This is how copper is refined.
Interactive 1 — Electrolysis Lab: Which Products, and How Much?

Choose an electrolyte and electrodes, a current $I$ and a time $t$. The beaker shows cations drifting to the cathode (−) and anions to the anode (+), with gas bubbles or a growing metal layer. On the right, the candidate electrode reactions compete: at the cathode the most easily reduced species wins, at the anode the most easily oxidised (✓). The readouts use $Q=It$ and $n=\tfrac{It}{zF}$ with $F=96\,500\ \mathrm{C\,mol^{-1}}$ and gas volumes at STP. Play runs the clock.

2.0 A30 min
charge $Q=It$—
electrons $n(\mathrm{e^{-}})$—
at the cathode (−)—
at the anode (+)—

An aqueous solution of sodium sulphate is electrolysed between platinum electrodes. The products are

Batteries and fuel cells

A laboratory cell with two beakers and a salt bridge is useless in a torch or a car. A practical battery (strictly, a battery is several cells joined in series, but the word is used for single cells too) must be compact, sealed, deliver a steady voltage under load, and use cheap materials.

📘 Definition 7.19 — Primary and secondary batteries

A primary battery (primary cell) works only once: its reaction cannot be reversed in practice, and when the reactants are used up it is discarded. Example: the dry (Leclanché) cell.

A secondary battery (storage cell, accumulator) can be recharged: passing a current through it in the opposite direction from an external source reverses the cell reaction by electrolysis, restoring the reactants. Examples: the lead accumulator, the nickel–cadmium cell and the lithium-ion cell.

The dry cell (Leclanché cell). The cheap "1.5 V" cell of torches and clocks has a zinc can as its anode and a graphite rod as the current collector of the cathode. The rod is packed in a moist mixture of manganese dioxide and carbon powder; the electrolyte is a paste of ammonium chloride and zinc chloride, so nothing can spill.

brass cap (+) graphite rod — cathode current collector MnO₂ + carbon powder (cathode) paste of NH₄Cl + ZnCl₂ (electrolyte) zinc can — anode (−) seal emf about 1.5 V
A dry cell in cross-section (not to scale).
$$\text{anode:}\quad \mathrm{Zn(s)\rightarrow Zn^{2+}(aq)+2e^{-}}$$ $$\text{cathode:}\quad \mathrm{MnO_{2}(s)+NH_{4}^{+}(aq)+e^{-}\rightarrow MnO(OH)(s)+NH_{3}(aq)}$$ $$\text{overall:}\quad \mathrm{Zn(s)+2MnO_{2}(s)+2NH_{4}^{+}(aq)\rightarrow Zn^{2+}(aq)+2MnO(OH)(s)+2NH_{3}(aq)}$$

Manganese is reduced from $+4$ to $+3$. The ammonia produced is taken up by the zinc ions as the complex $\mathrm{[Zn(NH_{3})_{4}]^{2+}}$. The cell gives about $1.5\ \mathrm{V}$, but because ammonia and other products accumulate around the cathode (they are not removed), the voltage drops during heavy use and partly recovers on rest; the zinc can is slowly attacked even when the cell is idle. It is a primary cell.

The lead accumulator. A car battery contains six cells in series, each about $2.0\ \mathrm{V}$, giving $12\ \mathrm{V}$. In each cell, grids of lead alloy are filled alternately with spongy lead (the anode) and lead dioxide (the cathode), dipping into sulphuric acid of about $38\%$ by mass (density about $1.30\ \mathrm{g\,mL^{-1}}$).

discharge (working as a galvanic cell)
anode (−): $\mathrm{Pb(s)+SO_{4}^{2-}(aq)\rightarrow PbSO_{4}(s)+2e^{-}}$
cathode (+): $\mathrm{PbO_{2}(s)+SO_{4}^{2-}(aq)+4H^{+}(aq)+2e^{-}\rightarrow PbSO_{4}(s)+2H_{2}O(l)}$
overall: $\mathrm{Pb(s)+PbO_{2}(s)+2H_{2}SO_{4}(aq)\rightarrow 2PbSO_{4}(s)+2H_{2}O(l)}$
charging (working as an electrolytic cell): every reaction above reversed
$\mathrm{2PbSO_{4}(s)+2H_{2}O(l)\rightarrow Pb(s)+PbO_{2}(s)+2H_{2}SO_{4}(aq)}$

Three features make it rechargeable and easy to monitor. Both electrode products are the same insoluble solid, $\mathrm{PbSO_{4}}$, which stays stuck to the plates where it formed, ready to be converted back. Sulphuric acid is consumed and water is formed on discharge — one mole of $\mathrm{H_{2}SO_{4}}$ per mole of electrons — so the density of the acid falls, and a hydrometer reading tells how charged the battery is. And lead is oxidised at one plate ($0\to+2$) while lead dioxide is reduced at the other ($+4\to+2$): the same element at both electrodes.

Fuel cells. In a heat engine, fuel is burnt, the heat drives a turbine or piston, and the second law of thermodynamics wastes most of the energy (a car engine turns only about a quarter of the fuel's energy into work). A fuel cell takes the Gibbs energy of the combustion reaction directly as electricity.

📘 Definition 7.20 — Fuel cell

A fuel cell is a galvanic cell in which the reactants — a fuel such as hydrogen, methane or methanol, and oxygen (or air) — are fed in continuously and the products removed, so that it delivers current for as long as fuel is supplied. Unlike a battery, it does not store its reactants.

In the hydrogen–oxygen fuel cell (developed by F. T. Bacon and used on the Apollo spacecraft), the gases are bubbled through porous carbon electrodes containing a finely divided platinum or palladium catalyst, into concentrated aqueous potassium hydroxide:

$$\text{anode:}\quad \mathrm{2H_{2}(g)+4OH^{-}(aq)\rightarrow 4H_{2}O(l)+4e^{-}}$$ $$\text{cathode:}\quad \mathrm{O_{2}(g)+2H_{2}O(l)+4e^{-}\rightarrow 4OH^{-}(aq)}$$ $$\text{overall:}\quad \mathrm{2H_{2}(g)+O_{2}(g)\rightarrow 2H_{2}O(l)},\qquad E^{\circ}_{cell}=1.23\ \mathrm{V}$$
📐 Result 7.19 — Maximum efficiency of a fuel cell

The heat released by burning the fuel at constant pressure is $-\Delta H$, while the most electrical work the cell can deliver is $-\Delta G$. The maximum (thermodynamic) efficiency is therefore

$$\eta_{\max}=\frac{\Delta G}{\Delta H}=1-\frac{T\Delta S}{\Delta H}.$$

For $\mathrm{H_{2}(g)+\tfrac12O_{2}(g)\rightarrow H_{2}O(l)}$ at $298\ \mathrm{K}$, $\Delta H^{\circ}=-285.8\ \mathrm{kJ\,mol^{-1}}$ and $\Delta G^{\circ}=-237.1\ \mathrm{kJ\,mol^{-1}}$, so $\eta_{\max}=83\%$. A real cell working at voltage $V$ (below $E$, because of overpotentials and internal resistance) delivers $nFV$ per mole: efficiency $=\dfrac{nFV}{-\Delta H}$. Unlike a heat engine, a fuel cell is not limited by the Carnot efficiency $1-\dfrac{T_{\text{cold}}}{T_{\text{hot}}}$.

Hydrogen–oxygen fuel cells are quiet, have no moving parts and emit only water. Their drawbacks are the cost of the platinum catalyst, and the energy needed to make, store and transport hydrogen; methanol and natural-gas fuel cells avoid the storage problem.

✏️ Example 5 — Inside a car battery (JEE level)
A $12\ \mathrm{V}$ lead accumulator (six cells in series) delivers a steady $40\ \mathrm{A}$ for $30\ \mathrm{min}$. For each cell find (a) the mass of $\mathrm{H_{2}SO_{4}}$ consumed, (b) the mass of lead consumed at the anode, and (c) the increase in mass of each electrode ($\mathrm{Pb}=207.2$, $\mathrm{H_{2}SO_{4}}=98.1$, $\mathrm{SO_{4}}=96.1$, $\mathrm{SO_{2}}=64.1$, $F=96\,500\ \mathrm{C\,mol^{-1}}$).
Find the mass of sulphuric acid consumed per cell (a) first:
Charge $Q=40\times1800=72\,000\ \mathrm{C}$; $n(\mathrm{e^{-}})=\dfrac{72\,000}{96\,500}=0.746\ \mathrm{mol}$. The cells are in series, so each cell passes this same charge.
(a) $2$ mol $\mathrm{H_{2}SO_{4}}$ per $2$ mol electrons: $n=0.746\ \mathrm{mol}$, $m=0.746\times98.1=73.2\ \mathrm{g}$ per cell.
(b) $\mathrm{Pb\rightarrow PbSO_{4}+2e^{-}}$: $n(\mathrm{Pb})=0.373\ \mathrm{mol}$, $m=0.373\times207.2=77.3\ \mathrm{g}$.
(c) Anode: each $\mathrm{Pb}$ becomes $\mathrm{PbSO_{4}}$, gaining $\mathrm{SO_{4}}$: $0.373\times96.1=35.8\ \mathrm{g}$. Cathode: each $\mathrm{PbO_{2}}$ becomes $\mathrm{PbSO_{4}}$, gaining $\mathrm{SO_{4}}$ and losing $\mathrm{O_{2}}$, a net gain of "$\mathrm{SO_{2}}$": $0.373\times64.1=23.9\ \mathrm{g}$. Both plates get heavier.
Check Plates gain $35.8+23.9=59.7\ \mathrm{g}$; the solution loses $73.2\ \mathrm{g}$ of acid but gains $0.746\times18.0=13.4\ \mathrm{g}$ of water, a net loss of $59.8\ \mathrm{g}$ ✓ (mass is conserved; difference from rounding).
✏️ Example 6 — How good is a fuel cell? (JEE level)
For $\mathrm{H_{2}(g)+\tfrac12O_{2}(g)\rightarrow H_{2}O(l)}$ at $298\ \mathrm{K}$, $\Delta H^{\circ}=-285.8\ \mathrm{kJ\,mol^{-1}}$ and $\Delta G^{\circ}=-237.1\ \mathrm{kJ\,mol^{-1}}$. (a) Find $E^{\circ}$ of the hydrogen–oxygen fuel cell. (b) Find its maximum efficiency. (c) A cell delivers $10\ \mathrm{A}$ at $0.90\ \mathrm{V}$ for $1.0\ \mathrm{h}$. How much hydrogen (in g) does it use, and what is its actual efficiency? ($F=96\,500\ \mathrm{C\,mol^{-1}}$.)
(a) $n=2$ per mole of $\mathrm{H_{2}}$: $E^{\circ}=\dfrac{-\Delta G^{\circ}}{nF}=\dfrac{237\,100}{2\times96\,500}=1.23\ \mathrm{V}$. (Writing the equation for $\mathrm{2H_{2}}$ doubles both $\Delta G^{\circ}$ and $n$; $E^{\circ}$ is the same.)
(b) $\eta_{\max}=\dfrac{237.1}{285.8}=0.830=83.0\%$.
(c) Hydrogen $Q=10\times3600=36\,000\ \mathrm{C}$, $n(\mathrm{e^{-}})=0.373\ \mathrm{mol}$, $n(\mathrm{H_{2}})=0.187\ \mathrm{mol}$, $m=0.187\times2.016=0.376\ \mathrm{g}$.
(c) Efficiency Work per mole of $\mathrm{H_{2}}$ at $0.90\ \mathrm{V}$: $2\times96\,500\times0.90=173.7\ \mathrm{kJ}$; efficiency $=\dfrac{173.7}{285.8}=60.8\%$ — still about twice that of a petrol engine.
Check $0.90\ \mathrm{V}\div1.23\ \mathrm{V}\times83.0\%=60.8\%$ ✓: the actual efficiency is the voltage efficiency times the thermodynamic one.

In the fuel-cell bench choose steam as the product and raise the temperature from $298\ \mathrm{K}$ to $1073\ \mathrm{K}$ (a solid-oxide fuel cell). What happens?

At $298\ \mathrm{K}$ (steam) the readouts show $\Delta G^{\circ}=-228.6\ \mathrm{kJ\,mol^{-1}}$, $E^{\circ}=1.18\ \mathrm{V}$, efficiency $94.5\%$. At $1073\ \mathrm{K}$: $\Delta G^{\circ}=-194.2\ \mathrm{kJ\,mol^{-1}}$, $E^{\circ}=1.01\ \mathrm{V}$, efficiency $80.3\%$, Carnot limit $72.2\%$. $\Delta S^{\circ}$ is negative (1.5 mol of gas becomes 1 mol), so $\Delta G^{\circ}=\Delta H^{\circ}-T\Delta S^{\circ}$ becomes less negative as $T$ rises, and $E^{\circ}=-\Delta G^{\circ}/2F$ falls. Hot cells are still used because their electrode reactions are fast without platinum. Switch to liquid water at 298 K: $E^{\circ}=1.23\ \mathrm{V}$ and $83.0\%$.
Interactive 2 — Fuel-Cell Bench: Gibbs Energy, Voltage and Efficiency

A hydrogen–oxygen fuel cell: $\mathrm{H_{2}}$ is oxidised at the anode, $\mathrm{O_{2}}$ reduced at the cathode, and electrons run through the lamp. Choose whether the water leaves as liquid (low-temperature cells) or steam (high-temperature cells) and set the temperature. The bars split the heat of combustion $|\Delta H^{\circ}|$ into the most electrical work, $|\Delta G^{\circ}|$ (green), and heat that must be released, $T|\Delta S^{\circ}|$ (amber), and compare with the best heat engine working between $T$ and $298\ \mathrm{K}$ (Carnot, purple). $\Delta H^{\circ}$ and $\Delta S^{\circ}$ are taken as constant. Play sweeps the temperature.

298 K
$\Delta G^{\circ}$ per mol H₂—
$E^{\circ}_{cell}=-\Delta G^{\circ}/2F$—
max efficiency $\Delta G/\Delta H$—
Carnot limit $1-298/T$—
🚀 Beyond JEE Main — Corrosion as an electrochemical cell

Corrosion is not in the JEE Main 2026 list; read this only for interest. Rusting of iron is a galvanic cell short-circuited through the metal itself. Where a drop of water touches iron, one region acts as an anode, $\mathrm{Fe(s)\rightarrow Fe^{2+}(aq)+2e^{-}}$; the electrons travel through the iron to another region, the cathode, where dissolved oxygen is reduced, $\mathrm{O_{2}(g)+4H^{+}(aq)+4e^{-}\rightarrow 2H_{2}O(l)}$ ($E^{\circ}_{cell}=1.23-(-0.44)=1.67\ \mathrm{V}$). The $\mathrm{Fe^{2+}}$ ions are further oxidised by air to hydrated iron(III) oxide, $\mathrm{Fe_{2}O_{3}\cdot xH_{2}O}$ — rust. Dissolved salts (better conduction) and acids ($\mathrm{H^{+}}$ for the cathode) speed it up. Protection either keeps water and oxygen away (paint, grease, plating with tin) or makes the iron a cathode: in galvanising or with blocks of magnesium on ship hulls, the more reactive metal is the anode and corrodes instead — "sacrificial protection".

⚠️ JEE Main traps

1. Units and $n$ in $\Delta G^{\circ}=-nFE^{\circ}$. $nFE^{\circ}$ comes out in joules per mole; divide by 1000 for kJ. $n$ is the electrons in the balanced equation as written — doubling the equation doubles $\Delta G^{\circ}$, never $E^{\circ}$.

2. Adding electrode potentials of half-reactions. To get $E^{\circ}_{\mathrm{Fe^{3+}/Fe}}$ from $\mathrm{Fe^{3+}/Fe^{2+}}$ and $\mathrm{Fe^{2+}/Fe}$, add $nE^{\circ}$ (i.e. $\Delta G^{\circ}$) and divide by the new $n$: $-0.037\ \mathrm{V}$, not $+0.33\ \mathrm{V}$.

3. Electrode signs. Anode = oxidation and cathode = reduction always; but the anode is negative in a galvanic cell and positive in an electrolytic cell.

4. Products from water. Aqueous $\mathrm{Na^{+}}$, $\mathrm{K^{+}}$, $\mathrm{Mg^{2+}}$, $\mathrm{Al^{3+}}$ salts never give the metal; sulphate and nitrate are never oxidised. Concentrated $\mathrm{NaCl}$ gives $\mathrm{Cl_{2}}$, very dilute $\mathrm{NaCl}$ mainly $\mathrm{O_{2}}$; a copper anode in $\mathrm{CuSO_{4}}$ dissolves.

5. Electrolysis arithmetic. Time in seconds in $Q=It$; $z=4$ for $\mathrm{O_{2}}$ but $2$ for $\mathrm{H_{2}}$ and $\mathrm{Cl_{2}}$; cells in series share the same charge, not the same mass. In the lead accumulator, $1$ mol $\mathrm{H_{2}SO_{4}}$ is used per mole of electrons and both plates gain mass on discharge.

While a lead accumulator is being discharged,

Exercises

Take $F=96\,500\ \mathrm{C\,mol^{-1}}$, $T=298\ \mathrm{K}$, $2.303RT/F=0.059\ \mathrm{V}$, gas volumes at STP $22.4\ \mathrm{L\,mol^{-1}}$, and standard potentials from Section 7.3 unless stated. Atomic masses: $\mathrm{H}=1.0$, $\mathrm{O}=16.0$, $\mathrm{Al}=27.0$, $\mathrm{Cu}=63.5$, $\mathrm{Ag}=107.9$, $\mathrm{Pb}=207.2$.

I
Cell potential, Gibbs energy and equilibrium.
  • 1 Find $\Delta_{r}G^{\circ}$ for $\mathrm{Cu(s)+2Ag^{+}(aq)\rightarrow Cu^{2+}(aq)+2Ag(s)}$ ($E^{\circ}_{cell}=0.46\ \mathrm{V}$).
  • 2 A one-electron cell reaction has $\Delta_{r}G^{\circ}=-96.5\ \mathrm{kJ\,mol^{-1}}$. Find $E^{\circ}_{cell}$.
  • 3 Find $\Delta_{r}G^{\circ}$ for the cell $\mathrm{Zn\,|\,Zn^{2+}\,\|\,Ag^{+}\,|\,Ag}$.
  • 4 Given $E^{\circ}_{\mathrm{MnO_{4}^{-}/Mn^{2+}}}=1.51\ \mathrm{V}$ and $E^{\circ}_{\mathrm{MnO_{2}/Mn^{2+}}}=1.23\ \mathrm{V}$ (both in acid), find $E^{\circ}_{\mathrm{MnO_{4}^{-}/MnO_{2}}}$.
  • 5 Find $\log K$ for $\mathrm{Ni(s)+2Ag^{+}(aq)\rightleftharpoons Ni^{2+}(aq)+2Ag(s)}$.
  • 6 A cell with $n=2$ has $E^{\circ}=1.018\ \mathrm{V}$ at $298\ \mathrm{K}$ and $\dfrac{dE^{\circ}}{dT}=-4.0\times10^{-5}\ \mathrm{V\,K^{-1}}$. Find $\Delta G^{\circ}$, $\Delta S^{\circ}$ and $\Delta H^{\circ}$.
  • 7 The equation $\mathrm{Zn+Cu^{2+}\rightarrow Zn^{2+}+Cu}$ is rewritten as $\mathrm{\tfrac12Zn+\tfrac12Cu^{2+}\rightarrow\tfrac12Zn^{2+}+\tfrac12Cu}$. What happens to $n$, $E^{\circ}$, $\Delta G^{\circ}$ and $K$?
  • 8 Using $E^{\circ}_{\mathrm{Cu^{2+}/Cu^{+}}}=0.15\ \mathrm{V}$ and $E^{\circ}_{\mathrm{Cu^{+}/Cu}}=0.53\ \mathrm{V}$, find $\Delta G^{\circ}$ for $\mathrm{Cu^{2+}(aq)+Cu(s)\rightarrow 2Cu^{+}(aq)}$. Is it spontaneous?
1 $\Delta G^{\circ}=-2\times96\,500\times0.46=-88\,780\ \mathrm{J\,mol^{-1}}=-88.8\ \mathrm{kJ\,mol^{-1}}$.
2 $E^{\circ}=\dfrac{96\,500}{1\times96\,500}=1.00\ \mathrm{V}$.
3 $E^{\circ}=1.56\ \mathrm{V}$, $n=2$: $\Delta G^{\circ}=-2\times96\,500\times1.56=-301\ \mathrm{kJ\,mol^{-1}}$.
4 $\mathrm{MnO_{4}^{-}\rightarrow Mn^{2+}}$ ($n=5$) $=$ $\mathrm{MnO_{4}^{-}\rightarrow MnO_{2}}$ ($n=3$) $+$ $\mathrm{MnO_{2}\rightarrow Mn^{2+}}$ ($n=2$): $5(1.51)=3E^{\circ}+2(1.23)$, $E^{\circ}=\dfrac{7.55-2.46}{3}=1.70\ \mathrm{V}$.
5 $E^{\circ}=0.80-(-0.25)=1.05\ \mathrm{V}$; $\log K=\dfrac{2\times1.05}{0.059}=35.6$.
6 $\Delta G^{\circ}=-2(96\,500)(1.018)=-196.5\ \mathrm{kJ\,mol^{-1}}$; $\Delta S^{\circ}=2(96\,500)(-4.0\times10^{-5})=-7.72\ \mathrm{J\,K^{-1}\,mol^{-1}}$; $\Delta H^{\circ}=\Delta G^{\circ}+T\Delta S^{\circ}=-196.5-2.30=-198.8\ \mathrm{kJ\,mol^{-1}}$.
7 $n$ halves ($2\to1$), $E^{\circ}$ is unchanged ($1.10\ \mathrm{V}$), $\Delta G^{\circ}$ halves ($-106\ \mathrm{kJ\,mol^{-1}}$), $K$ becomes $\sqrt{K}$ ($\log K$ halves to $18.6$).
8 Cathode couple $\mathrm{Cu^{2+}/Cu^{+}}$ ($0.15$), anode couple $\mathrm{Cu^{+}/Cu}$ ($0.53$): $E^{\circ}=-0.38\ \mathrm{V}$, $n=1$, $\Delta G^{\circ}=+96\,500\times0.38=+36.7\ \mathrm{kJ\,mol^{-1}}$. Not spontaneous — the reverse (disproportionation of $\mathrm{Cu^{+}}$) is.
II
Quantitative electrolysis.
  • 1 A current of $2.5\ \mathrm{A}$ flows for $20\ \mathrm{min}$. Find the charge and the moles of electrons.
  • 2 What mass of silver is deposited from $\mathrm{AgNO_{3}(aq)}$ by the charge in part 1?
  • 3 How long (in minutes) must a current of $5.0\ \mathrm{A}$ flow through molten alumina (in cryolite) to produce $1.00\ \mathrm{g}$ of aluminium?
  • 4 What volume of hydrogen at STP is liberated at the cathode by $0.50\ \mathrm{F}$?
  • 5 Two cells containing $\mathrm{AgNO_{3}(aq)}$ and $\mathrm{CuSO_{4}(aq)}$ are connected in series. $2.16\ \mathrm{g}$ of silver is deposited in the first. Find the mass of copper deposited in the second.
  • 6 How many faradays are needed to reduce $1\ \mathrm{mol}$ of $\mathrm{MnO_{4}^{-}}$ to $\mathrm{Mn^{2+}}$? To reduce $1\ \mathrm{mol}$ of $\mathrm{Cr_{2}O_{7}^{2-}}$ to $\mathrm{Cr^{3+}}$?
  • 7 A current of $3.00\ \mathrm{A}$ for $1.00\ \mathrm{h}$ deposits $3.20\ \mathrm{g}$ of copper. Find the current efficiency.
  • 8 Acidulated water is electrolysed with $1.0\ \mathrm{A}$ for $1.0\ \mathrm{h}$. Find the total volume of gas (in mL, STP) collected from both electrodes.
1 $Q=2.5\times1200=3000\ \mathrm{C}$; $n(\mathrm{e^{-}})=\dfrac{3000}{96\,500}=0.0311\ \mathrm{mol}$.
2 $\mathrm{Ag^{+}+e^{-}\rightarrow Ag}$: $0.0311\times107.9=3.35\ \mathrm{g}$.
3 $n(\mathrm{Al})=\dfrac{1.00}{27.0}=0.0370\ \mathrm{mol}$, $n(\mathrm{e^{-}})=0.111\ \mathrm{mol}$, $Q=10\,722\ \mathrm{C}$, $t=\dfrac{10\,722}{5.0}=2144\ \mathrm{s}=35.7\ \mathrm{min}$.
4 $0.50\ \mathrm{mol}$ electrons give $0.25\ \mathrm{mol}$ $\mathrm{H_{2}}$: $5.6\ \mathrm{L}$.
5 $n(\mathrm{e^{-}})=\dfrac{2.16}{107.9}=0.0200\ \mathrm{mol}$; $n(\mathrm{Cu})=0.0100\ \mathrm{mol}$, $m=0.636\ \mathrm{g}$.
6 $\mathrm{Mn}$: $+7\to+2$, $5\ \mathrm{F}$. $\mathrm{Cr_{2}O_{7}^{2-}}$: two Cr each $+6\to+3$, $6\ \mathrm{F}$.
7 Expected: $\dfrac{3.00\times3600}{96\,500}\times\dfrac{63.5}{2}=3.553\ \mathrm{g}$; efficiency $=\dfrac{3.20}{3.553}=90.1\%$.
8 $n(\mathrm{e^{-}})=\dfrac{3600}{96\,500}=0.0373\ \mathrm{mol}$: $\mathrm{H_{2}}$ $0.01865\ \mathrm{mol}$ ($418\ \mathrm{mL}$) and $\mathrm{O_{2}}$ $0.00933\ \mathrm{mol}$ ($209\ \mathrm{mL}$); total $627\ \mathrm{mL}$, in the ratio $2:1$.
III
Products of electrolysis.
  • 1 Give the products at the electrodes when aqueous $\mathrm{AgNO_{3}}$ is electrolysed with platinum electrodes.
  • 2 Give the products of the electrolysis of molten $\mathrm{KBr}$.
  • 3 Give the products of the electrolysis of aqueous $\mathrm{KBr}$ (inert electrodes).
  • 4 Give the products of the electrolysis of concentrated aqueous $\mathrm{CuCl_{2}}$ (inert electrodes).
  • 5 Aqueous $\mathrm{Na_{2}SO_{4}}$ containing litmus is electrolysed between platinum electrodes. What colours appear near each electrode, and why?
  • 6 In the electrorefining of copper, which electrode is made of impure copper? What happens to impurities of silver and of zinc?
  • 7 How many of the following aqueous solutions give oxygen at a platinum anode: $\mathrm{Na_{2}SO_{4}}$, $\mathrm{KNO_{3}}$, concentrated $\mathrm{NaCl}$, $\mathrm{CuSO_{4}}$, $\mathrm{KI}$, dilute $\mathrm{H_{2}SO_{4}}$, $\mathrm{NaOH}$?
  • 8 How many of the following give a metal at the cathode: $\mathrm{AgNO_{3}(aq)}$, $\mathrm{NaCl(aq)}$, $\mathrm{CuSO_{4}(aq)}$, $\mathrm{KNO_{3}(aq)}$, molten $\mathrm{MgCl_{2}}$, $\mathrm{Al_{2}(SO_{4})_{3}(aq)}$?
  • 9 $500\ \mathrm{mL}$ of concentrated brine is electrolysed with $0.965\ \mathrm{A}$ for $1000\ \mathrm{s}$. Find the pH of the solution afterwards (volume unchanged, $298\ \mathrm{K}$).
  • 10 For $\mathrm{H_{2}O(l)\rightarrow H_{2}(g)+\tfrac12O_{2}(g)}$, $\Delta G^{\circ}=+237.1\ \mathrm{kJ\,mol^{-1}}$. Find the minimum voltage needed to electrolyse water under standard conditions. Why do real electrolysers need about $1.8$–$2\ \mathrm{V}$?
1 Cathode: $\mathrm{Ag}$ ($\mathrm{Ag^{+}+e^{-}\rightarrow Ag}$). Anode: $\mathrm{O_{2}}$ from water (nitrate is not oxidised); $\mathrm{HNO_{3}}$ forms in solution.
2 Cathode: potassium metal; anode: bromine. No water — the only ions are $\mathrm{K^{+}}$ and $\mathrm{Br^{-}}$.
3 Cathode: $\mathrm{H_{2}}$ ($\mathrm{K^{+}}$ is not reduced); anode: $\mathrm{Br_{2}}$ ($E^{\circ}=1.09\ \mathrm{V}$, easier to oxidise than water); $\mathrm{KOH}$ remains.
4 Cathode: copper; anode: chlorine.
5 Cathode: $\mathrm{2H_{2}O+2e^{-}\rightarrow H_{2}+2OH^{-}}$ — alkaline, blue. Anode: $\mathrm{2H_{2}O\rightarrow O_{2}+4H^{+}+4e^{-}}$ — acidic, red. Stirring mixes them back to neutral, since $\mathrm{Na_{2}SO_{4}}$ is unchanged.
6 The impure copper is the anode; pure copper is deposited on a thin pure-copper cathode. Silver (and gold) are harder to oxidise than copper and fall as "anode mud"; zinc (and iron) are oxidised but their ions are harder to reduce than $\mathrm{Cu^{2+}}$ and stay in solution.
7 $\mathrm{O_{2}}$ from $\mathrm{Na_{2}SO_{4}}$, $\mathrm{KNO_{3}}$, $\mathrm{CuSO_{4}}$, dilute $\mathrm{H_{2}SO_{4}}$ and $\mathrm{NaOH}$: 5. (Concentrated $\mathrm{NaCl}$ gives $\mathrm{Cl_{2}}$, $\mathrm{KI}$ gives $\mathrm{I_{2}}$.)
8 $\mathrm{Ag}$ from $\mathrm{AgNO_{3}}$, $\mathrm{Cu}$ from $\mathrm{CuSO_{4}}$, $\mathrm{Mg}$ from molten $\mathrm{MgCl_{2}}$: 3. The others give $\mathrm{H_{2}}$.
9 $Q=965\ \mathrm{C}$, $n(\mathrm{e^{-}})=0.0100\ \mathrm{mol}=n(\mathrm{OH^{-}})$; $[\mathrm{OH^{-}}]=0.0200\ \mathrm{M}$, $\mathrm{pOH}=1.70$, $\mathrm{pH}=12.30$.
10 $E=\dfrac{237\,100}{2\times96\,500}=1.23\ \mathrm{V}$. Real cells need more: the overpotentials of $\mathrm{O_{2}}$ and $\mathrm{H_{2}}$ evolution and the voltage needed to drive current through the electrolyte ($IR$).
IV
Batteries and fuel cells.
  • 1 Write the electrode reactions of the dry cell and the change in the oxidation state of manganese. Why does its voltage fall during heavy use?
  • 2 How many lead–acid cells are connected in series in a $12\ \mathrm{V}$ car battery?
  • 3 What mass of $\mathrm{H_{2}SO_{4}}$ is consumed in one cell of a lead accumulator when it delivers $0.20\ \mathrm{F}$?
  • 4 A lead accumulator supplies $5.0\ \mathrm{A}$ for $2.0\ \mathrm{h}$. Find the mass of lead consumed at the anode of each cell.
  • 5 Explain why the lead accumulator can be recharged while the dry cell cannot. Write the reaction at the negative plate during charging.
  • 6 (Modelling) A hydrogen fuel cell operating at $0.80\ \mathrm{V}$ supplies $1.0\ \mathrm{kWh}$ of electrical energy. What mass of hydrogen does it consume?
  • 7 For $\mathrm{CH_{4}(g)+2O_{2}(g)\rightarrow CO_{2}(g)+2H_{2}O(l)}$, $\Delta G^{\circ}=-818\ \mathrm{kJ\,mol^{-1}}$. Find $E^{\circ}$ of a methane fuel cell.
  • 8 Using $\Delta H^{\circ}=-890\ \mathrm{kJ\,mol^{-1}}$ for the reaction in part 7, find the maximum efficiency of the methane fuel cell.
1 Anode $\mathrm{Zn\rightarrow Zn^{2+}+2e^{-}}$; cathode $\mathrm{MnO_{2}+NH_{4}^{+}+e^{-}\rightarrow MnO(OH)+NH_{3}}$; Mn goes from $+4$ to $+3$. Products ($\mathrm{NH_{3}}$, $\mathrm{Zn^{2+}}$) build up near the electrodes and are not removed quickly, so the voltage sags under heavy load.
2 $12\div2.0=6$ cells.
3 $1$ mol $\mathrm{H_{2}SO_{4}}$ per faraday: $0.20\times98.1=19.6\ \mathrm{g}$.
4 $Q=36\,000\ \mathrm{C}$, $n(\mathrm{e^{-}})=0.373\ \mathrm{mol}$, $n(\mathrm{Pb})=0.187\ \mathrm{mol}$, $m=38.6\ \mathrm{g}$ (in every cell).
5 In the accumulator both products ($\mathrm{PbSO_{4}}$) are insoluble solids held on the plates, so an external current can turn them back into $\mathrm{Pb}$ and $\mathrm{PbO_{2}}$. In the dry cell products diffuse away and side reactions occur. Negative plate on charging (now the cathode): $\mathrm{PbSO_{4}(s)+2e^{-}\rightarrow Pb(s)+SO_{4}^{2-}(aq)}$.
6 $Q=\dfrac{3.6\times10^{6}\ \mathrm{J}}{0.80\ \mathrm{V}}=4.5\times10^{6}\ \mathrm{C}$; $n(\mathrm{e^{-}})=46.6\ \mathrm{mol}$, $n(\mathrm{H_{2}})=23.3\ \mathrm{mol}$, $m=47.0\ \mathrm{g}$.
7 Carbon goes from $-4$ to $+4$: $n=8$. $E^{\circ}=\dfrac{818\,000}{8\times96\,500}=1.06\ \mathrm{V}$.
8 $\eta_{\max}=\dfrac{818}{890}=91.9\%$.
🎯 Exam corner JEE Main · MCQJEE Main · Numerical

E1. JEE Main · MCQ Given $E^{\circ}_{\mathrm{Cu^{2+}/Cu}}=0.34\ \mathrm{V}$ and $E^{\circ}_{\mathrm{Cu^{+}/Cu}}=0.52\ \mathrm{V}$, the value of $E^{\circ}_{\mathrm{Cu^{2+}/Cu^{+}}}$ is (A) $0.86\ \mathrm{V}$ (B) $0.16\ \mathrm{V}$ (C) $0.18\ \mathrm{V}$ (D) $-0.18\ \mathrm{V}$

Idea $\mathrm{Cu^{2+}+e^{-}\rightarrow Cu^{+}}$ = $(\mathrm{Cu^{2+}+2e^{-}\rightarrow Cu})$ − $(\mathrm{Cu^{+}+e^{-}\rightarrow Cu})$. Combine $nE^{\circ}$ values (Gibbs energies), not potentials.
Value $1\cdot E^{\circ}=2(0.34)-1(0.52)=0.16\ \mathrm{V}$.
Answer (B).
⏱ Shortcut (C) is $0.52-0.34$ — the "subtract the potentials" trap; (A) adds them.

E2. JEE Main · Numerical For the cell $\mathrm{Zn(s)\,|\,Zn^{2+}(aq)\,\|\,Ag^{+}(aq)\,|\,Ag(s)}$, $E^{\circ}_{\mathrm{Zn^{2+}/Zn}}=-0.76\ \mathrm{V}$ and $E^{\circ}_{\mathrm{Ag^{+}/Ag}}=+0.80\ \mathrm{V}$. The standard Gibbs energy of the cell reaction is $-x\ \mathrm{kJ\,mol^{-1}}$. Find $x$ ($F=96\,500\ \mathrm{C\,mol^{-1}}$). Give the answer to the nearest integer.

Cell $\mathrm{Zn+2Ag^{+}\rightarrow Zn^{2+}+2Ag}$, $n=2$, $E^{\circ}=0.80+0.76=1.56\ \mathrm{V}$.
ΔG° $-2\times96\,500\times1.56=-301\,080\ \mathrm{J\,mol^{-1}}=-301.1\ \mathrm{kJ\,mol^{-1}}$.
Answer $301$.
⏱ Shortcut $2F=193\ \mathrm{kJ\,V^{-1}\,mol^{-1}}$; $193\times1.56\approx301$.

E3. JEE Main · MCQ An aqueous solution of $\mathrm{Na_{2}SO_{4}}$ is electrolysed using platinum electrodes. The products at the cathode and the anode respectively are (A) $\mathrm{Na}$, $\mathrm{O_{2}}$ (B) $\mathrm{H_{2}}$, $\mathrm{SO_{2}}$ (C) $\mathrm{H_{2}}$, $\mathrm{O_{2}}$ (D) $\mathrm{Na}$, $\mathrm{S_{2}O_{8}^{2-}}$

Cathode $\mathrm{Na^{+}}$ ($-2.71\ \mathrm{V}$) loses to water ($-0.83\ \mathrm{V}$): $\mathrm{H_{2}}$.
Anode Sulphate is not oxidised at an ordinary anode; water gives $\mathrm{O_{2}}$.
Answer (C).
⏱ Shortcut Group-1 cation + oxoanion in water: only water is electrolysed.

E4. JEE Main · Numerical In a hydrogen–oxygen fuel cell the reaction $\mathrm{H_{2}(g)+\tfrac12O_{2}(g)\rightarrow H_{2}O(l)}$ has $\Delta G^{\circ}=-237\ \mathrm{kJ\,mol^{-1}}$ and $\Delta H^{\circ}=-286\ \mathrm{kJ\,mol^{-1}}$ at $298\ \mathrm{K}$. Find the maximum efficiency of the cell in percent. Give the answer to the nearest integer.

Idea Maximum electrical work $=-\Delta G$; heat that the same reaction would give on burning $=-\Delta H$.
Value $\eta=\dfrac{237}{286}\times100=82.9\%$.
Answer $83$.

E5. JEE Main · MCQ Which statement about a lead storage battery during discharge is correct? (A) $\mathrm{PbO_{2}}$ is the anode (B) the density of the electrolyte increases (C) $\mathrm{Pb}$ is reduced to $\mathrm{PbSO_{4}}$ at the cathode (D) sulphuric acid is consumed and water is formed, so the density of the electrolyte falls

Reaction $\mathrm{Pb+PbO_{2}+2H_{2}SO_{4}\rightarrow 2PbSO_{4}+2H_{2}O}$.
Reject $\mathrm{PbO_{2}}$ is reduced (cathode), so (A) is false; acid is used up, so (B) is false; $\mathrm{Pb}$ is oxidised at the anode, so (C) is false.
Answer (D).
⏱ Shortcut Discharge: acid → water, density down; a hydrometer reads the state of charge.

E6. JEE Main · Numerical The same quantity of electricity is passed through two electrolytic cells in series containing aqueous $\mathrm{AgNO_{3}}$ and aqueous $\mathrm{CuSO_{4}}$. If $2.16\ \mathrm{g}$ of silver is deposited in the first cell, find the mass of copper (in mg) deposited in the second ($\mathrm{Ag}=108$, $\mathrm{Cu}=63.5$). Give the answer to the nearest integer.

Electrons $n(\mathrm{Ag})=\dfrac{2.16}{108}=0.0200\ \mathrm{mol}=n(\mathrm{e^{-}})$.
Copper $n(\mathrm{Cu})=0.0100\ \mathrm{mol}$, $m=0.635\ \mathrm{g}=635\ \mathrm{mg}$.
Answer $635$.
⏱ Shortcut $m_{\mathrm{Cu}}=m_{\mathrm{Ag}}\times\dfrac{63.5/2}{108/1}=2.16\times\dfrac{31.75}{108}$.
🔬 Research–Teaching NexusResearch-tutored · optional, about 60 minutes

Research question. How much of the electrical energy fed into a simple water electrolyser ends up stored in the hydrogen it makes — and where does the rest go?

Why it matters. "Green hydrogen", made by electrolysing water with solar or wind power, is planned as a clean fuel for steelmaking, fertiliser plants, ships and heavy trucks in India, Europe, Australia and elsewhere. Its cost depends almost entirely on the electricity used per kilogram of hydrogen. Thermodynamics says $1.23\ \mathrm{V}$ is enough; real electrolysers run at $1.8$–$2\ \mathrm{V}$. The difference is overpotential and resistance — exactly what research on new catalysts and membranes tries to reduce.

What to do.

  1. Make a cell from two pencil leads (graphite) or stainless-steel screws pushed through the lid of a small container, filled with $0.5\ \mathrm{M}$ sodium sulphate or sodium carbonate solution (with a teacher). Invert two small graduated tubes or syringes full of the solution over the electrodes.
  2. Connect a $9\ \mathrm{V}$ battery (or an adjustable supply) through a multimeter set to measure current. Record the current every minute and the voltage across the cell.
  3. Run for 10–20 minutes. Read the volume of hydrogen, and convert to moles using the ideal-gas equation at room temperature and pressure.
  4. Compute the charge $Q=\sum I\,\Delta t$ and the hydrogen expected from $Q/2F$: the ratio is the current efficiency. Compute the energy supplied, $\sum VI\,\Delta t$, and compare it with $237\ \mathrm{kJ}$ per mole of hydrogen: the ratio is the energy efficiency.
  5. Repeat at a lower voltage (for example $3\ \mathrm{V}$ from two cells) and see how both efficiencies change.

Tools: Graphite pencil leads or steel screws, sodium sulphate or washing soda, small graduated tubes or syringes, multimeter, battery or bench supply, stopwatch, a spreadsheet.

Hand in: A table of current, voltage and gas volumes; your current efficiency and energy efficiency with a short error discussion; one paragraph explaining, in terms of overpotential and $IR$ loss, why the energy efficiency is so much lower than the current efficiency.

Going further. Check the $2:1$ volume ratio of hydrogen to oxygen. Why is it often less than 2 at first? (Think about oxygen's solubility and its reaction with graphite.) Estimate the cost of 1 kg of hydrogen at your local electricity price at the energy efficiency you measured.

Instructor note: current efficiency is usually $85$–$100\%$ for hydrogen; the oxygen volume often comes out low because oxygen dissolves and oxidises graphite anodes (CO₂). Energy efficiency at $9\ \mathrm{V}$ is only about $15$–$20\%$ (most of the voltage is lost in the solution resistance), rising to $40$–$60\%$ near $2.5$–$3\ \mathrm{V}$. Avoid chloride electrolytes (chlorine) and keep currents below about $0.5\ \mathrm{A}$.

🧪 Self-check quiz

0/5 correct

Q1. The Faraday constant is

Q2. In an electrolytic cell,

Q3. Concentrated aqueous sodium chloride is electrolysed between inert electrodes. The products are

Q4. Which of these is a secondary (rechargeable) cell?

Q5. For a cell reaction at $298\ \mathrm{K}$, $E^{\circ}_{cell}$ is positive. Then